6SD106EI - N/A - Datasheet.Directory

6&$/('ULYHU

Data Sheet 6SD106E

Internet: www.IGBT-Driver.com Page 1

Six-pack SCALE Driver 6SD106E

for IGBTs and Power MOSFETs

Description

The SCALE drivers from

CONCEPT are based on a chip

set that was developed

specifically for the reliable

driving and safe operation of

IGBTs and power MOSFETs.

The name “SCALE” is an acronym for

the most outstanding properties of the

SCALE series of drivers:

SCALE = Scaleable, C ompact, A ll purpose, L ow cost and E asy to use.

The SCALE driver is a winning project of the competition organized by “Technology

Center Switzerland 1998”. And ABB Switzerland AG honored the development of the

SCALE driver by distinguishing it as the “best power electronics project in 1998”.

Product Highlights Applications

✔ Suitable for IGBTs and power MOSFETs ✔ Inverters

✔ Short circuit and overcurrent protection ✔ Motor drive technology

✔ Extremely reliable, long service life ✔ Traction

✔ High gate current of ±6A ✔ Railroad power supplies

✔ Electrical isolation of 4000VAC ✔ Converters

✔ Electrically isolated status acknowledgement ✔ Power engineering

✔ Monitoring of power supply and self-monitoring ✔ Switched-mode power supplies

✔ Switching frequency DC to >100kHz ✔ Radiology and laser technology

✔ Duty cycle: 0... 100% ✔ DC/DC converter

✔ High dv/dt immunity, guaranteed >100,000V/µs ✔ Research

✔ Complete with DC/DC converter ✔ RF generators and converters

IGD

LDI

LDI = Logic to Driver Interface

IGD = Intelligent Gate Driver

6&$/('ULYHU

Data Sheet 6SD106E

Page 2 Internet: www.CT-CONCEPT.com

Block Diagram

Viso1

VDC

GND

IGD

LDI Viso1

Viso2

Electronic Level Power

Isolation Power Level Semiconductor

Driver onInterface on

PWM

oscillator

Electrical

SCALE Driver Module

(external)

Rth

VDD

GND

Fig. 1 Block diagram shows 2 channels (i.e. one third) of the 6SD106E

The block diagram shows two channels (i.e. one third) of the 6SD106E six-pack

driver. There is only one PWM oscillator, whereas all other components are present in

triplicate.

6&$/('ULYHU

Data Sheet 6SD106E

Internet: www.IGBT-Driver.com Page 3

Pin Designation

Pin Des. Function

1 GND Ground of the power supply

2 U_SO2 Phase U, Status output channel 2

3 U_Mod Phase U, Mode input

4 U_RC2 Phase U, RC network channel 2

5 U_InB Phase U, Input B

6 U_InA Phase U, Input A

7 U_RC1 Phase U, RC network channel 1

8 U_VL Phase U, Logic level/Reset

9 U_SO1 Phase U, Status output channel 1

10 GND Ground of DC/DC converter

11 GND Ground of DC/DC converter

12 VDC +15V for DC/DC converter

13 VDC +15V for DC/DC converter

14 V_SO2 Phase V, Status output channel 2

15 V_Mod Phase V, Mode input

16 V_RC2 Phase V, RC network channel 1

17 V_InB Phase V, Input B

18 V_InA Phase V, Input A

19 V_RC1 Phase V, RC network channel 1

20 V_VL Phase V, Logic level/Reset

21 V_SO1 Phase V, Status output channel 1

22 GND Ground of the power supply

23 GND Ground of the power supply

24 VDD +15V for electronic input side

25 VDD +15V for electronic input side

26 W_SO2Phase W, Status output channel 2

27 W_ModPhase W, Mode input

28 W_RC2 Phase W, RC network channel 2

29 W_InB Phase W, Input B

30 W_InA Phase W, Input A

31 W_RC1 Phase W, RC network channel 1

32 W_VL Phase W, Logic level/Reset

33 W_SO1Phase W, Status output channel 1

34 GND Ground of the power supply

Pin Des. Function

68 U_C2 Phase U, Collector sense ch. 2

67 U_Rth2 Phase U, Reference resistor ch. 2

66 U_E2 Phase U, Emitter channel 2

65 U_G2 Phase U, Gate channel 2

64 Free

63 Free

62 U_C1 Phase U, Collector sense ch. 1

61 U_Rth1 Phase U, Reference resistor ch. 1

60 U_E1 Phase U, Emitter channel 1

59 U_G1 Phase U, Gate channel 1

58 Free

57 Free

56 V_C2 Phase V, Collector sense ch. 2

55 V_Rth2 Phase V, Reference resistor ch. 2

54 V_E2 Phase V, Emitter channel 2

53 V_G2 Phase V, Gate channel 2

52 Free

51 Free

50 V_C1 Phase V, Collector sense ch. 1

49 V_Rth1 Phase V, Reference resistor ch. 1

48 V_E1 Phase V, Emitter channel 1

47 V_G1 Phase V, Gate channel 1

46 Free

45 Free

44 W_C2 Phase W, Collector sense ch. 2

43 W_Rth2 Phase W, Reference resistor ch. 2

42 W_E2 Phase W, Emitter channel 2

41 W_G2 Phase W, Gate channel 2

40 Free

39 Free

38 W_C1 Phase W, Collector sense ch. 1

37 W_Rth1 Phase W, Reference resistor ch. 1

36 W_E1 Phase W, Emitter channel 1

35 W_G1 Phase W, Gate channel 1

Legend:

Pins with the designation “Free” are not physically present

6&$/('ULYHU

Data Sheet 6SD106E

Page 4 Internet: www.CT-CONCEPT.com

Mechanical Dimensions

Fig. 2 Front view (top) / Layout overview component side (bottom) 6SD106E

Grid of the aspect drawing on page 4 below: 2.54mm (100mil)

Recommended diameter of solder pad: Ø 1.6mm; diameter of drill holes: Ø 1.0mm

6&$/('ULYHU

Data Sheet 6SD106E

Internet: www.IGBT-Driver.com Page 5

Fig. 3 Side view (top) / Mechanical fixing (bottom) 6SD106E

Height X: typ. 25mm in first series (1998); typ. 16mm from 1999

6&$/('ULYHU

Data Sheet 6SD106E

Page 6 Internet: www.CT-CONCEPT.com

Mechanical fixing

The 6SD106E driver has two holes each 2.7mm in diameter. They allow additional

fixing of the driver for applications requiring very high resistance to shaking/vibration

(railways, traction systems, electrically-driven vehicles, etc.). See Fig. 3 (bottom).

Absolute Maximum Ratings

Parameter Test conditions min max unit

Supply voltage VDC 016 Vdc

Supply voltage VDD 016 Vdc

Logic input voltage to GND 0 VDD Vdc

Gate peak current Iout Gx to Ex -6 +6 A

Output power DC/DC converter total for 6 channels 6 W

Operating voltage continuous (see Note 8) 800 Vdc

Test voltage (50Hz/1min) inputs to outputs 4000 VAC(eff)

Operating temperature 6SD106EN (see Note 10) 0 +70 °C

6SD106E I (see Note 10) -40 +85 °C

Storage temperature all types -40 +90 °C

All data refer to +25°C and VDD = VD C = 15V unless otherwise specified

Electrical Characteristics

Power supply Test conditions min typ max unit

Nominal supply voltage VDC to GND (see Note 1) 15 Vdc

Supply current IDC without load 70 mA

Max. supply current IDC (see Note 2) 460 mA

Output power DC/DC converter (see Note 3) 6W

Efficiency ηinternal DC/DC converter 85 %

Nominal supply voltage VDD to GND 15 Vdc

Supply current IDD without load 35 mA

Supply current IDD at 25kHz switching frequency 44 mA

6&$/('ULYHU

Data Sheet 6SD106E

Internet: www.IGBT-Driver.com Page 7

Electrical Characteristics (Continuation)

Power supply monitoring Test conditions min typ max unit

Turn-on threshold Vth (see Note 4) 11.5 Vdc

Hysteresis on-/off (see Note 4) 0.7 Vdc

Logic inputs Test conditions min typ max unit

Input voltage all inputs (see Note 5) 0VDD Vdc

Timing characteristics Test conditions min typ max unit

Delay time input to output turn-on tpd(on) 300 ns

turn-off tpd(off) 350 ns

Blocking time after failure (see Note 14) 1s

Outputs Test conditions min typ max unit

Output current IG Gx to Ex (see Note 6) -6 +6 Adc

Output rise time tr(out) Gx to Ex (see Note 7) 100 ns

Output fall time tf(out) Gx to Ex (see Note 7) 80 ns

Output current SOx 1.5 mA

Output voltage rating SOx SOx to GND VDD V

Vce-Monitoring Test conditions min typ max unit

Inputs Cx to Ex 0 VDD Vdc

Electrical isolation Test conditions min typ max unit

Operating voltage continuous (see Note 8) 800 Vdc

Test voltage (50Hz/1min) (see Note 12) 4000 VAC(eff)

Partial discharge extinction volt. IEC270 (see Note 11) >1200 VAC(pk)

Creep path input-output 12.7 mm

Creep path output-output (see Note 13) 7.0/12.7 mm

Maximum DV/Dt at DV =1000V (see Note 9) 100 kV/ms

All data refer to +25°C and VDD = VD C = 15V unless otherwise specified

6&$/('ULYHU

Data Sheet 6SD106E

Page 8 Internet: www.CT-CONCEPT.com

Operating conditions

Operating conditions Test conditions min max unit

Operating temperature 6SD106EN (see Note 10) 0 +70 °C

6SD106E I (see Note 10) -40 +85 °C

Storage temperature all types -40 +90 °C

Footnotes to the key data

1) The drivers have a zener diode on each channel for over-voltage protection. When the feed voltage

exceeds 16V, this protection can be subject to thermal overload.

2) If the specified power consumption is exceeded, this indicates an overload of the DC/DC converter. It

should be noted that these DC/DC converters are not protected against overload.

3) This should be considered as a recommended value. Please consult the section: “Output power and

self-heating”.

4) Under-voltage monitoring for protecting the power semiconductors. The voltage refers to the local supply

voltage of each individual drive channel. However, this corresponds approximately to the voltage at

VDC with respect to GND.

5) The input levels must never exceed the limits of the supply voltage (i.e. between GND and VDD),

otherwise latch-up of the integrated circuits LDI 00I can occur. Particular care must be taken when

driving via cables or longer leads.

6) The gate current must be limited to its maximum value by a gate resistor.

7) At a load of 39nF in series with 5.6 W (typical load of a 1200V/100A IGBT).

8) Maximum continuous or repeatedly-applied DC voltage or peak value of the repeatedly-applied AC

voltage between all inputs and all outputs. However, types that have been measured and selected for

higher partial-discharge voltages (e.g. for 1700V IGBT modules) are also available (see Note 11).

9) This specification guarantees that the drive information will be transferred reliably even at a high DC-

link voltage and fastest switching operations.

10) The application-specific self-heating of the drivers - specially at high load - must be taken into account.

11) The partial discharge is not measured for the standard types. Tested and selected types with guaranteed

partial-discharge immunity can be supplied for applications with maximum requirements and higher

operating voltages (such as railroad applications).

12) The test voltage of 4000 Vac(rms)/50Hz may be applied only once during a minute. It should be noted

that with this (strictly speaking obsolete) test method, some (minor) damage occurs to the isolation layers

due to the partial discharge. Consequently, this test is not performed at CONCEPT as a series test. In the

case of repeated isolation tests (e.g. module test, equipment test, system test) the subsequent tests should

be performed with a lower test voltage: the test voltage is reduced by 400V for each additional test. The

more modern if more elaborate partial-discharge measurement is better suited than such test methods as

it is almost entirely non-destructive.

13) The first series (1988) has a creep path of 7.0mm between adjacent channels. A creep path of 12.7mm

will be implemented (with 100% mechanical compatibility) in later series.

14) The typical blocking time after an error is 1 second. If required, versions with other blocking times

may also be supplied.

6&$/('ULYHU

Data Sheet 6SD106E

Internet: www.IGBT-Driver.com Page 9

Application Hints

IMPORTANT INFORMATION

This data sheet contains only product-specific data. All data that apply

to the whole type series of SCALE drivers is given in the document

entitled: “Description and Application Manual for SCALE Drivers”. In

particular, this manual contains a detailed description of the concept of

the SCALE drivers, a description of the function of all terminal pins as

well as other important application hints.

Overview and application

The SCALE driver 6SD106E is a six-pack driver for power MOSFETs and IGBTs.

The terminal pins of the 6SD106E driver are arranged so that the layout can be kept

very simple and the logic signal flow (input signal ⇒ drive circuit ⇒ power transistors) is

maintained. A distance of 12.7mm is observed between the drive signal and the power

potential!

Collector sense and dimensioning of Rth

The 6SD106E six-

path driver has a

collector-sense circuit

to protect the power

semiconductors. It is

shown in Fig. 4

Its basic operating

mode can be ob-

tained from the

brochure entitled:

“Description and

Application Manual

for Scale Drivers”.

To correspond more

effectively to the turn-

on characteristic of

the IGBTs, the SCALE

V+V+

5WK[

Rthx

RGx

Dm (2 x 1N4007)

SCALE Driver Module

IGD 001

150uA1.4mA

OVERCURRENT

MEASURING

Fig. 4 Collector-sense circuit principle

6&$/('ULYHU

Data Sheet 6SD106E

Page 10 Internet: www.CT-CONCEPT.com

drivers do not use a static reference

voltage to compare the voltage at the

collector. Instead, the reference is

used as shown in Fig. 5.

Notes on Table 1

The values for “Vth1” and “Vth2” are

listed in Table 1 as a function of the

reference resistance Rth.

The value in the “Vth1” column cor-

responds to the voltage threshold after

the response time has elapsed.

The value in the “Vth2” column cor-

responds to the voltage which is set up

statically across the resistor Rth. This

static value is typically reached after

between 10 and 15 µs.

The value in the “VCE(off)” column

corresponds to the collector-emitter

voltage value at which the protection

function is activated when the external

circuit is used as shown in Fig. 4 with

one or two Dm diodes of type

1N4007 connected in series.

Value Rth Reaction time Vth1 Vth2 VCE(off)

22k £ 4.9ms£ 4.8V £ 3.2V 2.35V (1 Diode)

27k £ 5.7ms£ 5.6V £ 3.9V 3.05V (1 Diode)

33k £ 6.8ms£ 6.5V £ 4.7V 3.25V (2 Diodes)

39k £ 7.6ms£ 7.3V £ 5.6V 4.15V (2 Diodes)

47k £ 9ms£ 8.4V £ 6.8V 5.35V (2 Diodes)

Table 1 Reference resistor, reaction time and turn-off threshold

+Vdc

Vth

Response time

Detail view

Detail

Vce

Vth1

Vce Vth2

Fig. 5 Collector-sense voltage curve

6&$/('ULYHU

Data Sheet 6SD106E

Internet: www.IGBT-Driver.com Page 11

Output power and self-heating

The specified output power of the driver totals 6W (1W per channel). This typically

suffices to drive a 100A/1200V six-pack IGBT module with 25kHz. In the case of a

drive power of 6W, the typical input power of the driver is about 7W; the losses due

to the driver total about 1 W. Because CONCEPT cannot predict how the drivers will

be incorporated in the user’s application, no binding recommended value for self-

heating and thus for the maximum useful output power at high ambient temperatures

can be made. It is consequently recommended to check the self-heating of the system,

especially when it is used at higher temperatures.

For the calculation of the exact output power, reference should be made to

Application Note AN-9701 “IGBT drivers correctly calculated” from CONCEPT.

If you need any help, simply call our technical support

CONCEPT offers you expert help for your questions and problems:

E-Mail: support@ct-concept.com or on the Internet: www.CT-CONCEPT.com

Fax international ++41 32 / 322 22 51 (in Switzerland: 032 / 322 22 51)

Tel international ++41 32 / 322 42 36 (in Switzerland: 032 / 322 42 36)

Quite special: customized SCALE drivers

If you need a power MOSFET or IGBT driver that is not included in the delivery range,

don’t hesitate to contact CONCEPT or your CONCEPT sales partner.

CONCEPT engineers have more than 15 years experience in the development and

manufacture of intelligent drivers for power MOSFETs and IGBTs and have already

implemented a large number of customized solutions.

Exclusion Clause

CONCEPT reserves the right to make modifications to its technical data and product

specifications at any time without prior notice. The general terms and conditions of

delivery of CT-Concept Technology Ltd. apply.

6&$/('ULYHU

Data Sheet 6SD106E

Page 12 Internet: www.CT-CONCEPT.com

Ordering Information

Six-pack SCALE driver with ±6A gate current / ±15V gate voltage

Standard version (0...70°C) 6SD106EN

Industry version (-40...+85°C) 6SD106EI

Additional Products and Information

Drivers for high isolation voltages (i.e. railroad applications)

Please request further information

Other intelligent drivers (i.e. half-bridge drivers etc.)

Please ask for following overviews from CONCEPT (also to be found on the Internet):

“Overview of Intelligent Drivers Standard Program”

“Overview of SCALE Drivers”

Evaluation boards

Please ask for following overview from CONCEPT (also to be found on the Internet):

“Overview and Price List of Evaluation-Boards”

Manufacturer Your Distribution Partner

CT-Concept Technology Ltd.

Intelligent Power Electronics

Hauptstrasse 3

CH-2533 Leubringen / Evilard

(Switzerland)

Tel ++41 (0)32 / 322 42 36

Fax ++41 (0)32 / 322 22 51

E-Mail info@ct-concept.com

Internet www.CT-CONCEPT.com

Internet www.IGBT-Driver.com

We reserve the right to make any technical modifications without prior notice. Version from 17.11.98