Temperature sensor ic
LM35CZ and LM35DZ
Issued March 1997
Data Pack E
RS stock numbers 317-954 and 317-960
The LM35 is a precision semiconductor temperature
sensor giving an output of 10mV per degree
Centigrade. Unlike devices with outputs proportional
to the absolute temperature (in degrees Kelvin) there
is no large offset voltage which, in most applications,
will have to be removed.
Accuracies of 1/4°C at room temperature or 3/4°C over
the full temperature range are typical.
Absolute maximum ratings(Note 10)
Supply voltage _____________________+35V to -0.2V
Output voltage _______________________+6V to -1.0V
Output current ____________________________10mA
Storage temperature, TO-92 package _-60°C to +150°C
Lead temperature (soldering, 10 seconds) ____260°C
Specified operating temperature range
TMIN to TMAX (Note 2)
LM35CZ ________________________ -40°C to +110°C
LM35DZ __________________________ 0°C to +100°C
Features
●Output proportional to °C
●Wide temperature range -40°C to +110°C
(CZ version)
●Accurate 1/4°C at room temperature typical
●Linear output 0.2°C typical
●Low current drain (60µA typical)
●Low self heating (0.08°C typical)
●Output impedance 0.1Ωat 1mA
●Standard T092 package.
Pin connections
Package details
232-2958
Data Sheet
232-2958
2
Notes:
1. Unless otherwise noted, these specifications apply: -40°≤TJ≤+ 110°C for the LM35C and 0°≤TJ≤+100°C for the LM35D. VS= +5Vdc and
ILOAD = 50µA, in the circuit of Figure 2. These specifications also apply from +2°C to TMAX in the circuit of Figure 1. Specifications in
boldfaceapply over the full rated temperature range.
2. Thermal resistance of the TO-92 package is 180°C/W junction to ambient.
3. Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects
can be computed by multiplying the internal dissipation by the thermal resistance.
4. Tested limits are guaranteed and 100% tested in production.
5. Design limits are guaranteed (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.
6. Specifications in boldface apply over the full rated temperature range.
7. Accuracy is defined as the error between the output voltage and 10mV/°C times the device's case temperature, at specified conditions of
voltage, current, and temperature (expressed in °C).
8. Non linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the device's
rated temperature range.
9. Quiescent current is defined in the circuit of Figure 1.
10. Absolute maximum ratings indicate limits beyond which damage to the device may occur. dc and ac electrical specifications are not
ensured when operating the device at absolute maximum ratings.
LM35CZ, LM35DZ
Parameter Conditions Tested Design Units
Typical Limit Limit (Max.)
(Note 4) (Note 5)
Accuracy, TA= +25°C ±0.4 ±1.0 °C
LM35, LM35C TA= -10°C ±0.5 ±1.5 °C
(Note 7) TA= TMAX ±0.8 ±1.5 °C
TA= TMIN ±0.8 ±2.0
Accuracy, TA= +25°C ±0.6 ±1.5 °C
LM35D TA= TMAX ±0.9 ±2.0 °C
(Note 7) TA= TMIN ±0.9 ±2.0 °C
Non linearity TMIN≤TA≤TMAX ±0.2 ±0.5 °C
(Note 8)
Sensor gain TMIN≤TA≤TMAX +10.0 +9.8 mV/°C
(Average slope) +10.2
Load regulation TA= +25°C ±0.4 ±2.0 mV/mA
(Note 3) 0≤IL≤1mA TMIN≤TA≤TMAX ±0.5 ±5.0 mV/mA
Line regulation TA= +25°C ±0.01 ±0.1 mV/V
(Note 3) 4V≤VS±≤30V ±0.02 ±0.2 mV/V
Quiescent current VS= +5V, +25°C 56 80 µA
(Note 9) VS= +5V 91 138 µA
VS= +30V, +25°C 56.2 82 µA
VS= +30V 91.5 141 µA
Change of 4V≤VS≤30V, +25°C 0.2 2.0 µA
quiescent current 4V≤VS≤30V 0.5 3.0 µA
(Note 3)
Temperature coefficient of +0.39 +0.7 µA/°C
quiescent current
Minimum temperature In circuit of +1.5 +2.0 °C
for rated accuracy Figure 1, IL= 0
Long term stability TJ-TMAX, for +0.08 °C
1000 hours
Electrical characteristics(Note 1) (Note 6)
232-2958
3
Application notes
The circuit shown in Figure 1 is a basic single ended
temperature sensor capable of measuring between
+2°C and +100°C or +110°C depending on version.
To measure negative temperatures a negative supply
is required as shown in Figure 2.
R1 should be selected as follows:
R1 = 50 310-6
Care must be taken when driving capacitive load, such
as long cables or any load exceeding 50pF.
To remove the effect of capacitive loads the circuit
shown Figure 3 should be used, however the resistor is
added to the output impedance making this circuit suit-
able for connection to high impedance loads only.
Figure 4 shows a circuit when will overcome this prob-
lem and also give protection from radiated interference
from relays or any other source of electrical noise.
Figure 1
Figure 4
Figure 2
Figure 3
The circuits below show some typical applications of
these temperature sensors.
-Vs
Figure 5 Two-wire remote temperature sensor
with sensor grounded
Figure 6 Two-wire remote temperature sensor
232-2958
Figure 7 Temperature sensor, single supply,
capable of measuring negative
temperatures
Figure 8 Centigrade thermometer
Figure 9 Expanded scale thermometer
The information provided in RS technical literature is believed to be accurate and reliable; however, RS Components assumes no responsibility for inaccuracies
or omissions, or for the use of this information, and all use of such information shall be entirely at the user’s own risk.
No responsibility is assumed by RS Components for any infringements of patents or other rights of third parties which may result from its use.
Specifications shown in RS Components technical literature are subject to change without notice.
RS Components, PO Box 99, Corby, Northants, NN17 9RS Telephone: 01536 201234
An Electrocomponents Company © RS Components 1997
