LH1540AT/AAB/AABTR 1 Form A Solid State Relay FEATURES * Current Limit Protection * l/O Isolation, 5300 VRMS * Typical RON 20 , max 25 * Load Voltage 350 V * Load Current 120 mA * High Surge Capability * Linear, AC/DC Operation * Clean Bounce Free Switching * Low Power Consumption * High Reliability Monolithic Receptor * SMD lead available on tape and reel * Flammability; UL94,VO Package Dimensions in Inches (mm) DIP DC S' 6 5 4 1 2 3 S Pin One ID. 3 2 1 4 5 6 S' .256 (6.50) .248 (6.30) .343 (8.70) .335 (8.50) .300 (7.62) Typ. .039 (1.00) Min. .150 (3.81) .130 (3.30) 4 Typ. AGENCY APPROVALS * UL - File No. E52744 * BSI/BABT Cert. No. 7980 * FIMKO Approval * CSA - Certification 093751 18 Typ. .020 (.051) Min. .035 (0.90) .031 (0.80) .022 (0.55) .018 (0.45) .100 (2.54) Typ. .014 (.35) .010 (.25) .150 (3.81) .110 (2.79) .347 (8.82) .300 (7.62) SMD .343 (8.71) .335 (8.51) APPLICATIONS * General Telecom Switching - On/off Hook Control - Ring Delay - Dial Pulse - Ground Start - Ground Fault Protection * Instrumentation * Industrial Controls * See Application Note 56 Pin one I.D. .256 (6.50) .248 (6.30) .050 (1.27) typ. .039 (0.99) min. DESCRIPTION The LH1540 is robust, ideal for telecom and ground fault applications. It is a SPST normally open switch (1 Form A) that replaces electromechanical relays in many applications. It is constructed using a GaAIAs LED for actuation control and an integrated monolithic die for the switch output. The die, fabricated in a high-voltage dielectrically isolated technology, is comprised of a photodiode array, switch control circuitry and MOSFET switches. In addition, it employs current-limiting circuitry which meets FCC 68.302 and other regulatory voltage surge requirements when overvoltage protection is provided. S .395 (10.03) .375 (9.63) .300 (7.62) typ. .052 (1.33) .048 (1.22) .150 (3.81) .130 (3.30) .0098 (.25) .0040 (.10) 3 to 7 18 4 .100 (2.54) .040 (1.016) .020 (0.508) .315 (8.00) min. .012 (0.31) .008 (0.20) Part Identification Part Number Description LH1540AT 6-pin DIP, Thru Hole LH1540AAB 6-pin SMD LH1540AABTR 6-pin SMD, Tape and Reel 2001 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) 3-154 March 23, 2001-12 Absolute Maximum Ratings, TA=25C Recommended Operating Conditions 120 IFon = 5.0 to 20 mA Load Current (mA) 100 80 60 40 IFon = 2.0 mA IFon = 3.0 mA IFon = 4.0 mA 20 0 -40 -20 0 20 40 60 80 Ambient Temperature (C) Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Ratings for extended periods of time can adversely affect reliability. Ambient Temperature Range (TA) .................................... -40 to +85C Storage Temperature Range (Tstg) ................................. -40 to +150C Pin Soldering Temperature (t=10 s max) (TS) ............................. 260C Input/Output Isolation Voltage (VISO) .................................. 5300 VRMS LED Continuous Forward Current (IF) .........................................50 mA LED Reverse Voltage (IR10 A) (VR)........................................... 8.0 V DC or Peak AC Load Voltage (IL50 A) (VL) .............................. 350 V Continuous DC Load Current (IL) Bidirectional Operation............................................................120 mA Unidirectional Operation..........................................................250 mA Peak Load Current (t=100 ms) (single shot) (IP) ................................ Output Power Dissipation (continuous) (PDISS)........................ 550 mW Refer to Current Limit Performance Application Note for a discussion on relay operation during transient currents. Electrical Characteristics, TA=25C Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. Parameter Sym. Min. Typ. Max. Units Test Conditions LED Forward Current, Switch Turn-on IFon -- 1.0 2.0 mA IL=100 mA, t=10 ms LED Forward Current, Switch Turn-off IFoff 0.2 0.9 -- mA VL300 V LED Forward Voltage VF 1.15 1.26 1.45 V IF=10 mA RON 12 20 25 IF=5.0 mA, IL=50 mA Input Output ON-resistance ac/dc: Pin 4 () to 6 () dc: Pin 4, 6 (+) to 5 () IF=5.0 mA, IL=100 mA 3.0 5.0 6.25 OFF-resistance ROFF 0.5 5000 -- G IF=0 mA, VL=100 V Current Limit ac/dc: Pin 4 () to 6 () ILMT 175 210 250 mA IF=5.0 mA, t=5.0 ms VL=6.0 V -- -- -- -- 0.32 200 nA IF=0 mA, VL=100 V -- 1.0 350 A IF=0 mA, VL=350 V 55 -- pF IF=0 mA, VL=1.0 V dc: Pin 4, 6 (+) to 5 () Off-state Leakage Current -- IF=5.0 mA, t=5.0 ms VL=4.0 V Output Capacitance Pin 4 to 6 -- -- -- 10 -- Switch Offset -- -- 0.15 -- V IF=5.0 mA Input/Output Capacitance CISO -- 0.8 -- pF VISO=1.0 V Turn-on Time ton -- 1.2 2.0 ms IF=5.0 mA, IL=50 mA Turn-off Time toff -- 0.5 2.0 ms IF=5.0 mA, IL=50 mA IF=0 mA, VL=50 V Transfer 2001 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) LH1540AT/AAB/AABTR 3-155 March 23, 2001-12 Typical Performance Characteristics Figure 4. Current Limit vs. Temperature Figure 1. LED Voltage vs. Temperature 40 1.5 IF=50 mA IF=20 mA 1.4 1.3 1.2 IF=1.0 mA 1.1 IF=2.0 mA 1.0 -40 IF=5.0 mA IF=10 mA -20 0 20 40 60 CHANGE IN CURRENT LIMIT (%) NORMALIZED TO 25C LED FORWARD VOLTAGE (V) 1.6 IF=5.0 mA t=5 ms VL=SEE ELEC. CHAR. 30 20 10 0 -10 -20 -30 -40 -40 80 Figure 2. LED Dropout Voltage vs. Temperature 20 40 60 80 Figure 5. ON-Resistance vs. Temperature 1.20 50 CHANGE IN ON-RESISTANCE (%) NORMALIZED TO 25C LED FORWARD VOLTAGE (V) 0 AMBIENT TEMPERATURE (C) AMBIENT TEMPERATURE (C) IL=100 mA 1.15 TYP. 1.10 MIN. 1.05 1.00 0.95 -40 -20 0 20 40 60 40 IL=50 mA 30 20 10 0 -10 -20 -30 -40 -40 80 100 IL=100 mA 80 60 40 20 0 -20 -40 -20 0 20 40 60 0 20 40 60 80 Figure 6. Variation in ON-Resistance vs. LED Current ac/dc ON-RESISTANCE VARIATION (%) NORMALIZED TC DATA SHEET RON SPECIFICATION @ IF=5.0 mA Figure 3. LED Current for Switch Turn-on vs. Temperature -60 -40 -20 AMBIENT TEMPERATURE (C) AMBIENT TEMPERATURE (C) LED FORWARD CURRENT FOR SWITCH TURN-ON (%) NORMALIZED TO 25C -20 1.5 IL=50 mA 1.0 0.5 0 -0.5 0 80 4 8 12 16 20 LED FORWARD CURRENT (mA) AMBIENT TEMPERATURE (C) 2001 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) LH1540AT/AAB/AABTR 3-156 March 23, 2001-12 Figure 10. Leakage Current vs. Applied Voltage OFF-STATE LEAKAGE CURRENT (pA) Figure 7. Switch Capacitance vs. Applied Voltage 80 IF=0 TA=25C f=1.0 MHz CAPACITANCE (pF) 70 60 50 40 30 20 10 0 0 20 40 60 80 100 90 IF=0 TA=25C 80 70 60 50 40 30 20 10 0 100 0 50 100 APPLIED VOLTAGE (V) INSERTION LOSS (dB) 0.30 RL=600 0.20 0.15 0.10 0.05 0 102 103 104 400 2.5 85C 2.0 1.5 70C 1.0 0.5 50C 0 50 100 150 200 250 300 350 400 LOAD VOLTAGE (V) VP=10 V RL=50 80 60 40 20 0 104 105 106 107 CHANGE IN BREAKDOWN VOLTAGE (%) NORMALIZED TO 25C Figure 12. Switch Breakdown Voltage vs. Temperature 100 ISOLATION (dB) 350 0 105 Figure 9. Output Isolation 103 250 300 3.0 FREQUENCY (Hz) 102 200 Figure 11. Leakage Current vs. Applied Voltage at Elevated Temperatures OFF-STATE LEAKAGE CURRENT (nA) Figure 8. Insertion Loss vs. Frequency 0.25 150 LOAD VOLTAGE (V) 8 6 4 2 0 -2 -4 -6 -8 -40 -20 0 20 40 60 80 AMBIENT TEMPERATURE (C) FREQUENCY (Hz) 2001 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) LH1540AT/AAB/AABTR 3-157 March 23, 2001-12 Figure 13. Switch Offset Voltage vs. Temperature Figure 16. Turn-off Time vs. Temperature CHANGE IN TURN-OFF TIME (%) NORMALIZED TO 25C SWITCH OFFSET VOLTAGE (V) 3.5 IF=5.0 mA 3.0 2.5 2.0 1.5 1.0 0.5 0 20 30 40 50 60 70 80 90 160 140 120 IF=5.0 mA IL=50 mA 100 80 60 40 20 0 -20 -40 -60 -80 -40 -20 Figure 14. Switch Offset Voltage vs. LED Current 40 60 80 Figure 17. Turn-on Time vs. LED Current 0.6 10 0.5 8 TURN-ON TIME (ms) SWITCH OFFSET VOLTAGE (V) 20 AMBIENT TEMPERATURE (C) AMBIENT TEMPERATURE (C) 0.4 0.3 0.2 IL=50 mA -40C 6 25C 85C 4 -40C 25C 85C 2 0.1 0 0 0 5 10 15 20 0 25 10 LED FORWARD CURRENT (mA) 20 30 40 50 LED FORWARD CURRENT (mA) Figure 15. Turn-on Time vs. Temperature Figure 18. Turn-off Time vs. LED Current 60 50 1.4 40 1.2 IL=50 mA TURN-ON TIME (ms) CHANGE IN TURN-ON TIME (%) NORMALIZED TO 25C 0 30 20 10 0 -10 -40C 1.0 0.8 25C 0.6 -20 -40 -40 0.4 IF=5.0 mA IL=50 mA -30 -20 0 20 40 60 85C 0.2 80 0 AMBIENT TEMPERATURE (C) 10 20 30 40 50 LED FORWARD CURRENT (mA) 2001 Infineon Technologies Corp. * Optoelectronics Division * San Jose, CA www.infineon.com/opto * 1-888-Infineon (1-888-463-4636) LH1540AT/AAB/AABTR 3-158 March 23, 2001-12