2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA LH1540AT/AAB/AABTR
www.infineon.com/opto • 1-888-Infineon (1-888-463-4636)
3–155 March 23, 2001-12
Absolute Maximum Ratings,
T
A
=25
°
C
Stresses in excess of the absolute Maximum Ratings can cause perma-
nent damage to the device. These are absolute stress ratings only. Func-
tional operation of the device is not implied at these or any other
conditions in excess of those given in the operational sections of this doc-
ument. Exposure to absolute Maximum Ratings for extended periods of
time can adversely affect reliability.
Ambient Temperature Range (
T
A
) ....................................–40 to +85
°
C
Storage Temperature Range (
T
stg
).................................–40 to +150
°
C
Pin Soldering Temperature (t=10 s max) (
T
S
) ............................. 260
°
C
Input/Output Isolation Voltage (
V
ISO
) .................................. 5300 V
RMS
LED Continuous Forward Current (
I
F
) .........................................50 mA
LED Reverse Voltage (
I
R
≤
10
µ
A) (
V
R
)...........................................8.0 V
DC or Peak AC Load Voltage (
I
L
≤
50
µ
A) (
V
L
).............................. 350 V
Continuous DC Load Current (
I
L
)
Bidirectional Operation............................................................120 mA
Unidirectional Operation..........................................................250 mA
Peak Load Current (t=100 ms) (single shot) (
I
P
) ................................ †
Output Power Dissipation (continuous) (
P
DISS
)........................550 mW
† Refer to Current Limit Performance Application Note for a discussion on
relay operation during transient currents.
Recommended Operating Conditions
80
60
0
40
120
100
20
–40 –20 0 20 40 60 80
Ambient Temperature (°C)
Load Current (mA)
I
Fon =
5.0 to 20 mA
I
Fon = 2.0 mA
I
Fon = 3.0 mA
I
Fon = 4.0 mA
Electrical Characteristics,
T
A
=25
°
C
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the
result of engineering evaluations. Typical values are for information only and are not part of the testing requirements.
Parameter Sym. Min. Typ. Max. Units Test Conditions
Input
LED Forward Current, Switch Turn-on
I
Fon
— 1.0 2.0 mA
I
L
=100 mA, t=10 ms
LED Forward Current, Switch Turn-off
I
Foff
0.2 0.9 — mA
V
L
±300 V
LED Forward Voltage
V
F
1.15 1.26 1.45 V
I
F
=10 mA
Output
ON-resistance
ac/dc: Pin 4 (±) to 6 (±)
R
ON
12 20 25
Ω
I
F
=5.0 mA,
I
L
=50 mA
dc: Pin 4, 6 (+) to 5 (±) 3.0 5.0 6.25
I
F
=5.0 mA,
I
L
=100 mA
OFF-resistance
R
OFF
0.5 5000 — G
Ω
I
F
=0 mA,
V
L
=±100 V
Current Limit
ac/dc: Pin 4 (±) to 6 (±)
I
LMT
175 210 250 mA
I
F
=5.0 mA, t=5.0 ms
V
L
=±6.0 V
dc: Pin 4, 6 (+) to 5 (±) — — —
I
F
=5.0 mA, t=5.0 ms
V
L
=±4.0 V
Off-state Leakage Current
—
— 0.32 200 nA
I
F
=0 mA,
V
L
=±100 V
— 1.0 350
µ
A
I
F
=0 mA,
V
L
=±350 V
Output Capacitance
Pin 4 to 6
—
—55—pF
I
F
=0 mA,
V
L
=1.0 V
—10—
I
F
=0 mA,
V
L
=50 V
Switch Offset — — 0.15 — V
I
F
=5.0 mA
Transfer
Input/Output Capacitance
C
ISO
— 0.8 — pF
V
ISO
=1.0 V
Turn-on Time
t
on
— 1.2 2.0 ms
I
F
=5.0 mA,
I
L
=50 mA
Turn-off Time
t
off
— 0.5 2.0 ms
I
F
=5.0 mA,
I
L
=50 mA