Thermoelectric Cooler Controller ADN8830 FEATURES High Efficiency Small Size: 5 mm 5 mm LFCSP Low Noise: <0.5% TEC Current Ripple Long-Term Temperature Stability: 0.01C Temperature Lock Indication Temperature Monitoring Output Oscillator Synchronization with an External Signal Clock Phase Adjustment for Multiple Controllers Programmable Switching Frequency up to 1 MHz Thermistor Failure Alarm Maximum TEC Voltage Programmability GENERAL DESCRIPTION The ADN8830 is a monolithic controller that drives a thermoelectric cooler (TEC) to stabilize the temperature of a laser diode or a passive component used in telecommunications equipment. This device relies on a negative temperature coefficient (NTC) thermistor to sense the temperature of the object attached to the TEC. The target temperature is set with an analog input voltage either from a DAC or an external resistor divider. The loop is stabilized by a PID compensation amplifier with high stability and low noise. The compensation network can be adjusted by the user to optimize temperature settling time. The component values for this network can be calculated based on the thermal transfer function of the laser diode or obtained from the lookup table given in the Application Notes section. APPLICATIONS Thermoelectric Cooler (TEC) Temperature Control Resistive Heating Element Control Temperature Stabilization Substrate (TSS) Control Voltage outputs are provided to monitor both the temperature of the object and the voltage across the TEC. A voltage reference of 2.5 V is also provided. FUNCTIONAL BLOCK DIAGRAM PID COMPENSATION NETWORK FROM THERMISTOR TEMPERATURE SET INPUT VREF P-CHANNEL (UPPER MOSFET) TEMPERATURE MEASUREMENT AMPLIFIER VOLTAGE REFERENCE PWM CONTROLLER N-CHANNEL MOSFET DRIVERS OSCILLATOR P-CHANNEL (LOWER MOSFET) N-CHANNEL FREQUENCY/PHASE CONTROL REV. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) 2003 Analog Devices, Inc. All rights reserved. V = 3.3 V to 5.0 V, V = 0 V, T = 25C, T = 25C, using typical application as shown in Figure 1, unless otherwise noted.) ADN8830-SPECIFICATIONS (@configuration DD Parameter Symbol TEMPERATURE STABILITY Long-Term Stability PWM OUTPUT DRIVERS Output Transition Time Nonoverlapping Clock Delay Output Resistance Output Voltage Swing Output Voltage Ripple Output Current Ripple LINEAR OUTPUT AMPLIFIER Output Resistance Output Voltage Swing POWER SUPPLY Power Supply Voltage Power Supply Rejection Ratio t R , tF SET Min CL = 3,300 pF 50 RO (N1, P1) OUT A OUT A ITEC IL = 50 mA VLIM = 0 V fCLK = 1 MHz fCLK = 1 MHz RO, P2 RO, N2 OUT B IOUT = 2 mA IOUT = 2 mA VDD PSRR ISY Shutdown Current Soft-Start Charging Current Undervoltage Lockout ISD ISS VOLOCK Open-Loop Input Impedance Gain-Bandwidth Product Conditions A Typ Using 10 k thermistor with = -4.4% at 25C Supply Current ERROR AMPLIFIER Input Offset Voltage Gain Input Voltage Range Common-Mode Rejection Ratio GND VOS AV, IN VCM CMRR 0 0.01 C VDD 0.2 0.2 85 178 3.0 80 60 VDD 5.5 92 8 5 15 2.0 Low-to-high threshold VCM = 1.5 V 0.2 V < VCM < 2.0 V -40C TA +85C Unit 20 65 6 0 VDD = 3.3 V to 5 V, VTEC = 0 V -40C TA +85C PWM not switching -40C TA +85C Pin 10 = 0 V Max 50 20 0.2 58 55 12 15 2.7 250 2.0 68 1 2 RIN GBW ns ns V % % V V dB dB mA mA A A V V V/V V dB dB G MHz REFERENCE VOLTAGE Reference Voltage VREF IREF < 2 mA 2.37 2.47 2.57 V OSCILLATOR Synchronization Range Oscillator Frequency fCLK fCLK Pin 25 connected to external clock Pin 24 = VDD; (R = 150 k; Pin 25 = GND) 200 800 1,000 1,000 1,250 kHz kHz 0.2 V V V V LOGIC CONTROL* Logic Low Input Threshold Logic High Input Threshold Logic Low Output Level Logic High Output Threshold 3 0.2 VDD - 0.2 *Logic inputs meet typical CMOS I/O conditions for source/sink current (~1 A). Specifications subject to change without notice. -2- REV. C ADN8830 ABSOLUTE MAXIMUM RATINGS* Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . GND to VS + 0.3 V Storage Temperature Range . . . . . . . . . . . . . -65C to +150C Operating Temperature Range . . . . . . . . . . . . -40C to +85C Operating Junction Temperature . . . . . . . . . . . . . . . . . . 125C Lead Temperature Range (Soldering, 10 sec) . . . . . . . . 300C Package Type JA* JC Unit 32-Lead LFCSP (ACP) 35 10 C/W *JA is specified for worst-case conditions, i.e., JA is specified for a device soldered in a 4-layer circuit board for surface-mount packages. ESD RATINGS 883 (Human Body) Model . . . . . . . . . . . . . . . . . . . . . . 1.0 kV *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ORDERING GUIDE Model Temperature Range Package Description Package Option ADN8830ACP ADN8830ACP-REEL ADN8830ACP-REEL7 ADN8830-EVAL -40C to +85C -40C to +85C -40C to +85C 32-Lead Lead Frame Chip Scale Package (LFCSP) 32-Lead Lead Frame Chip Scale Package (LFCSP) 32-Lead Lead Frame Chip Scale Package (LFCSP) Evaluation Board CP-32-1 CP-32-1 CP-32-1 32 NC 31 TEMPOUT 30 AGND 29 PHASE 28 SYNCOUT 27 SOFTSTART 26 FREQ 25 SYNCIN PIN CONFIGURATION PIN 1 INDICATOR ADN8830 TOP VIEW 24 COMPOSC 23 PGND 22 N1 21 P1 20 PVDD 19 OUT A 18 COMPSWIN 17 COMPSWOUT OUT B 9 N2 10 P2 11 TEMPCTL 12 COMPFB 13 COMPOUT 14 VLIM 15 VTEC 16 THERMFAULT 1 THERMIN 2 SD 3 TEMPSET 4 TEMPLOCK 5 NC 6 VREF 7 AVDD 8 NC = NO CONNECT CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADN8830 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. C -3- ADN8830 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Type Description 1 THERMFAULT Digital Output Indicates an Open or Short-Circuit Condition from Thermistor. 2 THERMIN Analog Input Thermistor Feedback Input. 3 SD Digital Input Puts Device into Low Current Shutdown Mode. Active low. 4 TEMPSET Analog Input Target Temperature Input. 5 TEMPLOCK Digital Output Indicates when Thermistor Temperature is within 0.1C of Target Temperature as Set by TEMPSET Voltage. 6 NC 7 VREF Analog Output 2.5 V Reference Voltage. 8 AVDD Power Power for Nondriver Sections. 3.0 V min; 5.5 V max. 9 OUT B Analog Input Linear Output Feedback. Will typically connect to TEC+ pin of TEC. 10 N2 Analog Output Drives Linear Output External NMOS Gate. 11 P2 Analog Output Drives Linear Output External PMOS Gate. 12 TEMPCTL Analog Output Output of Error Amplifier. Connects to COMPFB through feedforward section of compensation network. 13 COMPFB Analog Input Feedback Summing Node of Compensation Amplifier. Connects to TEMPCTL and COMPOUT through compensation network. 14 COMPOUT Analog Output Output of Compensation Amplifier. Connects to COMPFB through feedback section of compensation network. 15 VLIM Analog Input Sets Maximum Voltage across TEC. 16 VTEC Analog Output Indicates Relative Voltage across the TEC. The 1.5 V corresponds to 0 V across TEC. The 3.0 V indicates maximum output voltage, maximum heat transfer through TEC. 17 COMPSWOUT Analog Output Compensation for Switching Amplifier. 18 COMPSWIN Analog Input Compensation for Switching Amplifier. Capacitor connected between COMPSWIN and COMPSWOUT. 19 OUT A Analog Input PWM Output Feedback. Will typically connect to TEC- pin of TEC. 20 PVDD Power Power for Output Driver Sections. 3.0 V min; 5.5 V max. 21 P1 Digital Output Drives PWM Output External PMOS Gate. 22 N1 Digital Output Drives PWM Output External NMOS Gate. 23 PGND Ground Power Ground. External NMOS devices connect to PGND. Can be connected to digital ground as noise sensitivity at this node is not critical. 24 COMPOSC Analog Input Connect as Indicated in the Application Notes Section. 25 SYNCIN Digital Input Optional Clock Input. If not connected, clock frequency set by FREQ pin. 26 FREQ Analog Input Sets Switching Frequency. 27 SOFTSTART Analog Input Controls Initialization Time for ADN8830 with Capacitor to Ground. 28 SYNCOUT Digital Output Phase Adjusted Clock Output. Phase set from PHASE pin. Can be used to drive SYNCIN of other ADN8830 devices. 29 PHASE Analog Input Sets Switching and SYNCOUT Clock Phase Relative to SYNCIN Clock. 30 AGND Ground Analog Ground. Should be low noise for highest accuracy. 31 TEMPOUT Analog Output Indication of Thermistor Temperature. 32 NC No Connection, except as Noted in the Application Notes Section. No Connection. -4- REV. C Typical Performance Characteristics-ADN8830 360 VDD = 5V TA = 25C SYNC IN = 200kHz TA = 25C 320 P1 VOLTAGE (1V/DIV) PHASE SHIFT (Degrees) 280 240 200 160 120 80 N1 40 0 0 0 0 0 0 0 0 0 TIME (20ns/DIV) 0 0 0 0 0 0.4 0.8 1.2 VPHASE (V) 1.6 2.0 2.4 TPC 4. Clock Phase Shift vs. Phase Voltage TPC 1. N1 and P1 Rise Time 2.480 VDD = 5V TA = 25C P1 VREF ( V) VOLTAGE (1V/DIV) 2.475 2.470 2.465 N1 2.460 2.455 -40 0 0 0 0 0 0 0 0 TIME (20ns/DIV) 0 0 0 0 60 85 TPC 5. VREF vs. Temperature TPC 2. N1 and P1 Fall Time 1,000 360 SYNC IN = 1MHz TA = 25C VDD = 5V TA = 25C SWITCHING FREQUENCY (kHz) 320 280 PHASE SHIFT (Degrees) 10 35 TEMPERATURE (C) -15 240 200 160 120 80 800 600 400 200 40 0 0 0 0.4 0.8 1.2 VPHASE (V) 1.6 2.0 2.4 TPC 3. Clock Phase Shift vs. Phase Voltage REV. C 0 250 500 750 1,000 RFREQ (k) 1,250 TPC 6. Switching Frequency vs. RFREQ -5- 1,500 ADN8830 1,000 SWITCHING FREQUENCY (kHz) 990 45 VDD = 5V RFREQ = 150k 40 35 SUPPLY CURRENT (mA) 980 970 960 950 940 25 20 15 5 920 -40 -15 10 35 TEMPERATURE (C) 60 0 200 85 TPC 7. Switching Frequency vs. Temperature 300 400 500 600 700 800 SWITCHING FREQUENCY (kHz) 900 1,000 TPC 10. Supply Current vs. Switching Frequency 70 2.06 THERM FAULT UPPER THRESHOLD (V) 65 OFFSET VOLTAGE (V) 30 10 930 60 55 50 45 40 35 30 -40 -15 10 35 TEMPERATURE (C) 60 2.05 2.04 2.03 2.02 -40 85 TPC 8. Offset Voltage vs. Temperature -15 10 35 TEMPERATURE (C) 60 85 TPC 11. Open Thermistor Fault Threshold vs. Temperature 200 THERM FAULT LOWER THRESHOLD (V) 0.26 100 OFFSET VOLTAGE (V) VDD = 5V TA = 25C USING CIRCUIT SHOWN IN FIGURE 1 0 -100 -200 -300 0.2 0.4 0.6 0.8 1.0 1.2 1.4 COMMON-MODE VOLTAGE (V) 1.6 1.8 0.24 0.23 -40 -400 0 0.25 2.0 TPC 9. Offset Voltage vs. Common-Mode Voltage -15 10 35 TEMPERATURE (C) 60 85 TPC 12. Short Thermistor Fault Threshold vs. Temperature -6- REV. C ADN8830 In addition, an effective controller should operate down to 3.3 V and have an indication of when the target temperature has been reached. The ADN8830 accomplishes all of these requirements with a minimum of external components. Figure 1 shows a reference design for a typical application. APPLICATION NOTES Principle of Operation The ADN8830 is a controller for a TEC and is used to set and stabilize the temperature of the TEC. A voltage applied to the input of the ADN8830 corresponds to a target temperature setpoint. The appropriate current is then applied to the TEC to pump heat either to or away from the object whose temperature is being regulated. The temperature of the object is measured by a thermistor and is fed back to the ADN8830 to correct the loop and settle the TEC to the appropriate final temperature. For best stability, the thermistor should be mounted in close proximity to the object. In most laser diode modules, the TEC and thermistor are already mounted in the unit and are used to regulate the temperature of the laser diode. Temperature is monitored by connecting the measurement thermistor to a precision amplifier, called the error amplifier, with a simple resistor divider. This voltage is compared against the temperature set input voltage, creating an error voltage that is proportional to their difference. To maintain accurate wavelength and power from the laser diode, this difference voltage must be as accurate as possible. For this reason, self-correction auto-zero amplifiers are used in the input stage of the ADN8830, providing a maximum offset voltage of 250 V over time and temperature. This results in final temperature accuracy within 0.01C in typical applications, eliminating the ADN8830 as an error source in the temperature control loop. A logic output is provided at TEMPLOCK to indicate when the target temperature has been reached. A complete TEC controller solution requires: * A precision input amplifier stage to accurately measure the difference between the target and object temperatures. * A compensation amplifier to optimize the stability and temperature settling time. * A high output current stage. Because of the high output currents involved, a TEC controller should operate with high efficiency to minimize the heat generated from power dissipation. The output of the error amplifier is then fed into a compensation amplifier. An external network consisting of a few resistors and capacitors is connected around the compensation amplifier. This network can be adjusted by the user to optimize the step SYNCOUT TEMPOUT 32 THERMFAULT THERMIN RTH 10k @25C 3.3V TEMPSET 31 C1 0.1F 30 29 28 27 R1 150k 26 1 R2 7.68k 0.1% VREF R3 10k 0.1% TEMPLOCK R4 7.68k 0.1% VREF 25 L1 4.7H COILCRAFT DO3316-472 3.3V 24 2 TEC- C2 22F CDE ESRD 23 Q1 FDW2520C-B 3 22 4 21 Q2 FDW2520C-A ADN8830 5 20 6 19 7 18 C3 10F 3.3V C4 22F CDE ESRD 3.3V C5 10nF 8 3.3V C8 10F 9 17 10 12 11 13 R5 205k C11 1F R7 1M 14 15 Q3 FDW2520C-A C6 2.2nF C10 330pF TEC+ VTEC Figure 1. Typical Application Schematic REV. C -7- C7 10F 16 C9 10F R6 100k 3.3V Q4 FDW2520C-B C12 3.3nF ADN8830 simple integrator or PID loop, the dc forward gain of the compensation section is equal to the open-loop gain of the compensation amplifier, which is over 80 dB or 10,000. The output from the compensation loop at COMPOUT is then fed to the linear amplifier. The output of the linear amplifier at OUT B is fed with COMPOUT into the PWM amplifier whose output is OUT A. These two outputs provide the voltage drive directly to the TEC. Including the external transistors, the gain of the differential output section is fixed at 4. Details on the output amplifiers can be found in the Output Driver Amplifiers section. response of the TEC's temperature either in terms of settling time or maximum current change. Details of how to adjust the compensation network are given in the Compensation Loop section. The ADN8830 can be easily integrated with a wavelength locker for fine-tune temperature adjustment of the laser diode for a specific wavelength. This is a useful topology for tunable wavelength lasers. Details are highlighted in the Using the TEC Controller ADN8830 with a Wave Locker section. The TEC is driven differentially using an H-bridge configuration to maximize the output voltage swing. The ADN8830 drives external transistors that are used to provide current to the TEC. These transistors can be selected by the user based on the maximum output current required for the TEC. The maximum voltage across the TEC can be set through use of the VLIM pin on the ADN8830. 1.5V 4 TEMPSET COMPENSATION PWM/LINEAR AMPLIFIERS AMPLIFIER INPUT AMPLIFIER 19 1.5V THERMIN To further improve the power efficiency of the system, one side of the H-bridge uses a switched output. Only one inductor and one capacitor are required to filter out the switching frequency. The output voltage ripple is a function of the output inductor and capacitor and the switching frequency. For most applications, a 4.7 H inductor, 22 F capacitor, and switching frequency of 1 MHz maintains less than 0.5% worst-case output voltage ripple across the TEC. The other side of the H-bridge does not require any additional circuitry. 2 AV = 20 OUT A OUT B 9 AV = Z2/Z1 12 TEMPCTL Z1 13 Z2 AV = 4 14 COMPOUT COMPFB Figure 2. Signal Flow Block Diagram of the ADN8830 Thermistor Setup The temperature of the thermal object, such as a laser diode, is detected with a negative temperature coefficient (NTC) thermistor. The thermistor's resistance exhibits an exponential relationship to the inverse of temperature, meaning the resistance decreases at higher temperatures. Thus, by measuring the thermistor resistance, temperature can be ascertained. Betatherm is a leading supplier of NTC thermistors. Thermistor information and details can be found at www.betatherm.com. The oscillator section of the ADN8830 controls the switched output section. A single resistor sets the switching frequency from 100 kHz to 1 MHz. The clock output is available at the SYNCOUT pin and can be used to drive another ADN8830 device by connecting to its SYNCIN pin. The phase of the clock is adjusted by a voltage applied to the PHASE pin, which can be set by a simple resistor divider. Phase adjustment allows two or more ADN8830 devices to operate from the same clock frequency and not have all outputs switch simultaneously, which could create an excessive power supply ripple. Details of how to adjust the clock frequency and phase are given in the Setting the Switching Frequency section. For this application, the resistance is measured using a voltage divider. The thermistor is connected between THERMIN (Pin 2) and AGND (Pin 30). Another resistor (RX) is connected between VREF (Pin 7) and THERMIN (Pin 2), creating a voltage divider for the VREF voltage. Figure 3 shows the schematic for this configuration. For effective indication of a catastrophic system failure, the ADN8830 alerts to open-circuit or short-circuit conditions from the thermistor, preventing an erroneous and potentially damaging temperature correction from occurring. With some additional external circuitry, output overcurrent detection can be implemented to provide warning in the event of a TEC short-circuit failure. This circuit is highlighted in the Setting Maximum Output Current and Short-Circuit Protection section. VDD 8 7 RX 2 Signal Flow Diagram ADN8830 RTHERM Figure 2 shows the signal flow diagram through the ADN8830. The input amplifier is fixed with a gain of 20. The voltage at TEMPCTL can be expressed as ( ) TEMPCTL = 20 x TEMPSET - THERMIN + 1.5 30 Figure 3. Connecting a Thermistor to the ADN8830 (1) With the thermistor connected from THERMIN to AGND, the voltage at THERMIN will decrease as temperature increases. To maintain the proper input-to-output polarity in this configuration, OUT A (Pin 19) should connect to the TEC- pin on the TEC, and OUT B (Pin 9) should connect to the VTEC+ pin. When the temperature is settled, the thermistor voltage will be equal to the TEMPSET voltage, and the output of the input amplifier will be 1.5 V. The voltage at TEMPCTL is then fed into the compensation amplifier whose frequency response is dictated by the compensation network. Details on the compensation amplifier can be found in the Compensation Loop section. When configured as a The thermistor can also be connected from VREF to THERMIN with RX connecting to ground. In this case, OUT A must connect to TEC+ with OUT B connected to TEC- for proper operation. -8- REV. C ADN8830 Although the thermistor has a nonlinear relationship to temperature, near optimal linearity over a specified temperature range can be achieved with the proper value of RX. First, the resistance of the thermistor must be known, where The setpoint voltage can be driven from a DAC or another voltage source, as shown in Figure 4. The reference voltage for the DAC should be connected to VREF (Pin 7) on the ADN8830 to ensure best accuracy from device to device. RTHERM = RT1 @ T = TLOW = RT 2 @ T = TMID For a fixed target temperature, a voltage divider network can be used as shown in Figure 5. R1 is set equal to RX, and R2 is equal to the value of RTHERM at the target temperature. (2) = RT 3 @ T = THIGH 3.3V TLOW and THIGH are the endpoints of the temperature range and TMID is the average. These resistances can be found in most thermistor data sheets. In some cases, only the coefficients corresponding to the Steinhart-Hart equation are given. The Steinhart-Hart equation is [ 1 = a + b1n (R ) + c 1n (R ) T ] 3 1-4 (3) ADN8830 30 Figure 4. Using a DAC to Control the Temperature Setpoint 3.3V 8 7 R1 4 1 b T and = c c a- R R + RT 2RT 3 - 2RT1RT 3 RX = T1 T 2 RT1 + RT 3 - 2RT 2 30 Figure 5. Using a Voltage Divider to Set a Fixed Temperature Setpoint (5) Design Example 1 A laser module requires a constant temperature of 25C. From the manufacturer's data sheet, we find the thermistor in the laser module has a value of 10 k at 25C. Because the laser is not required to operate at a range of temperatures, the value of RX can be set to 10 k. TEMPSET can be set by a simple resistor divider as shown in Figure 5, with R1 and R2 both equal to 10 k. For the best accuracy as well as the widest selection range for resistances, RX should be 0.1% tolerance. Naturally, the smaller the temperature range required for control, the more linear the voltage divider will be with respect to temperature. The voltage at THERMIN is VX = VREF RTHERM RTHERM + RX Design Example 2 (6) A laser module requires a continuous temperature control from 5C to 45C. The manufacturer's data sheet shows the thermistor has a value of 10 k at 25C, 25.4 k at 5C, and 4.37 k at 45C. Using Equation 5, RX is calculated to be 7.68 k to yield the most linear temperature-to-voltage conversion. A DAC will be used to set the TEMPSET voltage. where VREF has a typical value of 2.47 V. The ADN8830 control loop will adjust the temperature of the TEC until VX equals the voltage at TEMPSET (Pin 4), which we define as VSET. Target temperature can be set by ( ) VSET = m T - TMID + VXMID (7) DAC Resolution for TEMPSET The temperature setpoint voltage to THERMIN can be set from a DAC. The DAC must have a sufficient number of bits to achieve adequate temperature resolution from the system. The voltage range for THERMIN is found by multiplying the variable m from Equation 8 by the temperature range. where T equals the target temperature, and VX , HIGH - VX , LOW THIGH - TLOW ADN8830 R2 RX is then found as (8) ( VX for high, mid, and low are found by using Equation 6 and substituting RT3, RT2, and RT1, respectively, for RTHERM. The variable m is the change in VX with respect to temperature and is expressed in V/C. REV. C 8 7 where m= 4 C 1 1 13 13 2 2 3 2 3 2 (4) = exp - + + + + - - 2 2 4 27 27 4 X= 8 6 AD7390 5 where T is the absolute temperature of the thermistor in Kelvin (K = C + 273.15), and R is the resistance of the thermistor at that temperature. Based on the coefficients a, b, and c, RTHERM can be calculated for a given T, albeit somewhat tediously, by solving the cubic roots of this equation RTHERM 3.3V 7 THERMIN Voltage Range = m x TMAX - TMIN ) (9) From Design Example 2, 40C of the control temperature range is achieved with a voltage range of only 1 V. -9- ADN8830 To eliminate the resolution of the DAC as the principal source of system error, the step size of each bit, VSTEP, should be lower than the desired system resolution. A practical value for absolute DAC resolution is the equivalent of 0.05C. The value of VSTEP should be less than the value of m from Equation 8 multiplied by the desired temperature resolution, or VSTEP < 0.05C x m Table I. Switching Frequencies vs. RFREQ (10) where m is the slope of the voltage-to-temperature conversion line, as found from Equation 8. From Design Example 2, where m = 25 mV/C, we see the DAC should have resolution better than 1.25 mV per step. ( ) ( log VFS - log VSTEP () ) log 2 RFREQ = (11) where VFS is the full-scale output voltage from the DAC, which should be equal to the reference voltage from the ADN8830, VREF = 2.47 V as given in the Specifications table for the Reference Voltage. In this example, the minimum resolution is 11 bits. A 12-bit DAC, such as the AD7390, can be readily found. It is important that the full-scale voltage input to the DAC is tied to the ADN8830 reference voltage, as shown in Figure 4. This eliminates errors from slight variances of VREF. Thermistor Fault and Temperature Lock Indications Both the THERMFAULT (Pin 1) and TEMPLOCK (Pin 5) outputs are CMOS compatible outputs that are active high. THERMFAULT will be a logic low while the thermistor is operating normally and will go to a logic high if a short or open is detected at THERMIN (Pin 2). The trip voltage for THERMFAULT is when THERMIN falls below 0.2 V or exceeds 2.0 V. THERMFAULT provides only an indication of a fault condition and does not activate any shutdown or protection circuitry on the ADN8830. To shut down the ADN8830, a logic low voltage must be asserted on Pin 3, as described in the Shutdown Mode section. TEMPLOCK will output a logic high when the voltage at THERMIN is within 2.5 mV of TEMPSET. This voltage can be related to temperature by solving for m from Equation 8. For most laser diode applications, 2.5 mV is equivalent to 0.1C. If the voltage difference between THERMIN and TEMPSET is greater than 2.5 mV, then TEMPLOCK will output a logic low. The input offset voltage of the ADN8830 is guaranteed to within 250 V, which for most applications is within 0.01C. 100 kHz 250 kHz 500 kHz 750 kHz 1 MHz 1.5 M 600 k 300 k 200 k 150 k 150 x 109 fSWITCH (12) where fSWITCH is the switching frequency in Hz. Higher switching frequencies reduce the voltage ripple across the TEC. However, high switch frequencies will create more power dissipation in the external transistors. This is due to the more frequent charging and discharging of the transistors' gate capacitances. If large transistors are needed for a high output current application, faster switching frequencies could reduce the overall power efficiency of the circuit. This is covered in detail in the Calculating Power Dissipation and Efficiency section. The switching frequency of the ADN8830 can be synchronized with an external clock by connecting the clock signal to SYNCIN (Pin 25). Pin 24 should also be connected to an R-C network, as shown in Figure 6. This network is simply used to compensate a PLL to lock on to the external clock. To ensure the quickest synchronization lock-in time, RFREQ should be set to 1.5 M. ADN8830 1nF COMPOSC 24 FREQ 26 1k 0.1F 1.5M Figure 6. Using an R-C Network on Pin 24 with an External Clock The relative phase of the ADN8830 internal oscillator compared to the external clock signal can be adjusted. This is accomplished by adjusting the voltage to PHASE (Pin 29) according to TPCs 3 and 4. The phase shift versus voltage can be approximated as Phase Shift = 360 x Setting the Switching Frequency The ADN8830 has an internal oscillator to generate the switching frequency for the output stage. This oscillator can be either set in free-run mode or synchronized to an external clock signal. For free-run operation, SYNCIN (Pin 25) should be connected to ground and COMPOSC (Pin 24) should be connected to AVDD. The switching frequency is then set by a single resistor connected from FREQ (Pin 26) to ground. Table I shows RFREQ for some common switching frequencies. RFREQ For other frequencies, the value for this resistor, RFREQ, should be set to The minimum number of bits required is then given as Number of Bits = fSWITCH VPHASE VREF (13) where VPHASE is the voltage at Pin 29, and VREF has a typical value of 2.47 V. To ensure the oscillator operates correctly, VPHASE should remain higher than 100 mV and lower than 2.3 V. This is required for either internal clock or external synchronization operation. A resistor divider from VREF to ground can establish this voltage easily, although any voltage source, such as a DAC, could be used as well. If phase is not a consideration, for example with a single ADN8830 being used, Pin 29 can be tied to Pin 6, which provides a 1.5 V reference voltage. -10- REV. C ADN8830 The phase adjusted output from the ADN8830 is available at SYNCOUT (Pin 28). This pin can be used as a master clock signal for driving other ADN8830 devices. Multiple ADN8830 devices can be either driven from a single master ADN8830 device by connecting its SYNCOUT pin to each slave's SYNCIN pin or daisy-chained by connecting each device's SYNCOUT to the next device's SYNCIN pin. Soft Start on Power-Up Phase shifting is useful in systems that use more than one ADN8830 TEC controller. It ensures the ADN8830 devices will not switch at the same time, which could create excessive ripple on the power supply voltage. By adjusting the phase of each device, the switching transients can be spaced equally over the clock period, reducing potential supply ripple and easing the instantaneous current demand from the supply. SS = 150 x CSS Using a single master clock, each slave ADN8830 should have a different value phase shift. For example, with four TEC controllers, one slave device should be set for 90 of phase shift, another for 180, and the last for 270. In a daisy-chain configuration, each slave device would be set with equal phase. Using the previous example, each slave would be set to 90 with its SYNCOUT pin connected to the next device's SYNCIN pin. Examples are shown in Figures 7 and 8. 25 28 ADN8830 24 50k 29 26 1k 24 28 ADN8830 25 MASTER 6 24 29 26 RFREQ 26 ADN8830 28 1nF 24 150k 29 26 1k 1nF 0.1F 1.5M 50k The ADN8830 has a shutdown mode that deactivates the output stage and puts the device into a low current standby state. The current draw for the ADN8830 in shutdown is less than 100 A. The shutdown input, Pin 3, is active low. To shut down the device, Pin 3 should be driven to logic low. Once a logic high is applied, the ADN8830 will reactivate after the delay set by the soft start circuitry. Refer to the Soft Start on Power-Up section for more details on this feature. A typical compensation network used for temperature control of a laser module is a PID loop, which consists of a very low frequency pole and two separate zeros at higher frequencies. Figure 9 shows a simple network for implementing PID compensation. An additional pole is added at a higher frequency than the zeros to reduce the noise sensitivity of the control loop. The bode plot of the magnitude is shown in Figure 10. NC SLAVE 7 1k 0.1F 1.5M 100k 25 NC SLAVE 100k 29 28 ADN8830 7 Shutdown Mode The ADN8830 TEC controller has a built-in amplifier dedicated for loop compensation. The exact compensation network is set by the user and can vary from a simple integrator to PI, PID, or any other type of network. The type of compensation and component values should be determined by the user since it will depend on the thermal response of the object and the TEC. One method for determining these values empirically is to input a step function to TEMPSET, thus changing the target temperature, and adjusting the compensation network to minimize the settling time of the object's temperature. VDD 25 where CSS is the value of the capacitor in microfarads, and SS is the soft start time in milliseconds. To set a soft start time of 15 ms, CSS should equal 0.1 F. A minimum soft start time of 10 ms is recommended to ensure proper initialization of the ADN8830 on power-up. Compensation Loop 1nF 0.1F 150k (14) Pin 3 should not be left floating as there are no internal pull-up or pull-down resistors. If the shutdown function is not required, Pin 3 should be tied to VDD to ensure the device is always active. NC SLAVE 7 The ADN8830 can be programmed to ramp up for a specified time after the power supply is applied or after shutdown is de-asserted. This feature, known as soft start, is useful for gradually increasing the duty cycle of the PWM amplifier. The soft start time is set with a single capacitor connected from Pin 27 to ground according to Equation 14. Figure 7. Multiple ADN8830 Devices Driven from a Master Clock 1nF 1nF 1nF VDD 0.1F 1k 24 NC 25 ADN8830 25 28 MASTER 7 6 0.1F 1k 24 ADN8830 7 150k 29 ADN8830 29 50k 7 29 50k 26 1.5M -11- 24 ADN8830 28 SLAVE 29 50k Figure 8. Multiple ADN8830 Devices Using a Daisy Chain REV. C 1k 150k 26 1.5M 25 28 SLAVE 150k 26 RFREQ 25 28 SLAVE 0.1F 24 26 1.5M NC ADN8830 MAGNITUDE (LOG SCALE) The unity-gain crossover frequency of the feedforward amplifier is given as 1 x 80 x TEC GAIN (15) 2R 3C1 To ensure stability, the unity-gain crossover frequency should be lower than the thermal time constant of the TEC and thermistor. However, this thermal time constant may not be specified and can be difficult to characterize. f0 dB = 0dB R1 R2||R3 R1 R3 There are many texts written on loop stabilization, and it is beyond the scope of this data sheet to discuss all methods and trade-offs in optimizing compensation networks. A simple method that can be used to empirically determine a PID compensation loop as shown in Figure 9 involves the following procedure: 1. Connect thermistor and TEC to the ADN8830 application circuit. Power does not need to be applied to the laser diode for this procedure. Monitor output voltage across the TEC with an oscilloscope. 2. Short C1 and open C2, leaving just R1 and R3 as a simple proportional-only compensation loop. 3. While maintaining a constant TEMPSET voltage, increase the ratio of R1/R3, thus increasing the gain until loop oscillation starts to occur. Decrease this ratio by a factor of 2 from the point of oscillation. The R1/R3 ratio will likely be less than unity for most laser modules. 4. Add C1 capacitor and decrease value until oscillation starts, then increase by a factor of 2. A good initial starting value for C1 is to create a unity-gain crossover of 0.1 Hz based on Equation 15. 5. Short R2 and increase C2 until oscillation starts. At this point, either C2 can be decreased or R2 can be added to regain stability. Generally speaking, R2 will be greater than R3 and C2 will be one or more orders of magnitude less than C1. 6. TEMPSET should be adjusted with a step change while observing the output voltage settling time. A step change of 100 mV should suffice. From here, C2, R2, and even C1 can be decreased to minimize settling time at the expense of additional output voltage overshoot. 7. An additional feedback capacitor, CF, in parallel with R1 and C1, can be added to add another high frequency pole. In many cases, this improves the stability of the system without increasing the settling time as out-of-band noise is filtered out of the control signal. A 330 pF to 1 nF capacitor should suffice, if required. 1 2R3C1 1 1 2R1C1 2C2(R2+R3) FREQUENCY (Hz LOG SCALE) Figure 10. Bode Plot for PID Compensation Using the TEC Controller ADN8830 with a Wave Locker Many optical applications require precision control of laser wavelength. The wavelength of the laser diode can be adjusted by changing its temperature, which is done through temperature control of the TEC. Wavelength control can be done by feeding a wave locker or etalon output back to the microprocessor and using the microprocessor to calculate and reinstruct the TEC controller with a new target temperature. However, this method is computationally expensive and has time delays before the adjustment is done. A faster responding and simpler method is to feed the wave locker signal back to the TEC controller for direct temperature control. The ADN8830 is designed to be compatible with a wave locker controller. Figure 11 shows the basic schematic. The TEMPCTL output from ADN8830 is proportional to the object's actual temperature. This voltage is fed to the wave locker controller. Also fed to the wave locker controller are the photodiode outputs from the wave locker, as well as the laser diode power and a digital signal indicating a functional laser diode, both of which come from the CW controller. The output of the wave locker controller is then connected to the input of the compensation network. This allows the wave locker controller to adjust the TEC temperature based on the current temperature of the object, the current wavelength of the laser diode, and the target wavelength. Once the target wavelength is reached, the wave locker controller sends a signal to the microcontroller indicating that the laser signal is good. The typical values shown in the typical application circuit in Figure 1 have R1 = 100 k, R2 = 1 M, R3 = 205 k, C1 = 10 F, C2 = 1 F, and an additional feedback capacitor of 330 pF. For most pump laser modules, this results in a 10C TEMPSET step settling time to within 0.1C in less than 5 seconds. FROM LOCKER ADN8830 ADN8830 REFERENCE VOLTAGE TEMPCTL COMPFB COMPOUT COMPFB 13 13 12 R3 R2 C1 R1 C2 14 LOCKER PD1 LOCKER PD2 WAVE LOCKER GOOD FROM CW CONTROLLER TEMPCTL 1 2R2C2 12 LASER DIODE POWER TO MICROPROCESSOR LASER DIODE GOOD TEC CONTROL TEMP IN COMPOUT 14 COMPENSATION NETWORK CF Figure 11. Using the ADN8830 with a Wave Locker Figure 9. Implementing a PID Compensation Loop -12- REV. C ADN8830 where VOUT A and VOUT B are the voltages at Pins 19 and 9, respectively. The ripple voltage at Pin 19 is filtered out internally and does not appear at VTEC, leaving it as an accurate dc output of the TEC voltage. Using TEMPOUT to Measure Temperature The TEMPOUT pin is a voltage that is proportional to the difference between the target temperature and the measured thermistor temperature. The full equation for the voltage at TEMPOUT is ( TEMPOUT = 1.5 + 3 x THERMIN - TEMPSET ) (16) The voltage range of TEMPOUT is 0 V to 3.0 V and is independent of power supply voltage. Setting the Maximum TEC Voltage and Current The ADN8830 can be programmed for a maximum output voltage to protect the TEC. A voltage from 0 V to 1.5 V applied to the VLIM (Pin 15) input to the ADN8830 sets the maximum TEC voltage, VTEC, MAX. This voltage can be set with either a resistor divider or from a DAC. Because the output of the ADN8830 is bidirectional, this voltage sets both the upper and lower limits of the TEC voltage. The equation governing VTEC, MAX is given in Equation 17 and the graph of this equation is shown in Figure 12. ( ) VTEC , MAX = 1.5V - VLIM x 4 To achieve a differential output, the ADN8830 has two separate output stages. OUT A is a switched output or pulse-width modulated (PWM) amplifier, and OUT B is a high gain linear amplifier. Although they achieve the same result, to provide constant voltage and high current, their operation is different. The exact equations for the two outputs are ( (17) 5 3 OUT B = -14 x (COMPOUT - 1.5) + 1.5 (20) OUT B = 4 x VTEC + 1.5 1 0 1.0 VLIM (V) 0.5 1.5 2.0 If the supply voltage is lower than VTEC, MAX, the maximum TEC voltage will obviously be equal to the supply voltage. The voltage to VLIM should not exceed 1.5 V since this causes improper operation of the output voltage limiting circuitry. Setting VLIM to 1.5 V can be used to deactivate the TEC current without shutting down the ADN8830 in the event of a system failure. If a maximum TEC voltage is not required, VLIM should be connected to ground. It is not advisable to leave VLIM floating as this would cause unpredictable output behavior. This feature should be used to limit the maximum output current to the TEC as specified in the TEC data sheet. For example, if the maximum TEC voltage is specified at 2 V, VLIM should be set to 1 V. The maximum output voltage is then set to 2 V. Output Driver Amplifiers The output voltage across the TEC as measured from Pin 19 to Pin 9 can be monitored at Pin 16. This is labeled as VTEC in the typical application schematic in Figure 1. The voltage at VTEC can vary from 0 V to 3 V independent of the power supply voltage. Its equation is given as ( VTEC = 0.25 x VOUT A ) - VOUT B + 1.5 (21) In Figure 1, Pins 10 and 11 provide the gate drive for Q3 and Q4, which complete the linear output amplifier. This output voltage is fed back to Pin 9 (OUT B) to close its loop. The gate-to-drain capacitance of Q3 and Q4 provide the compensation for the linear amplifier. If using the recommended FDW2520C transistors, it will be necessary to add an additional 2.2 nF of capacitance from the gate to the drain of the PMOS transistor to maintain stability. A 3.3 nF capacitor should also be connected from the drain to ground to prevent small oscillations when there is very little or no current through the TEC. Figure 12. VLIM Voltage vs. Maximum TEC Voltage REV. C (19) Because the COMPOUT voltage is not readily known, Equation 20 can be rewritten in terms of the TEC voltage, VTEC, which is defined as OUT B - OUT A. 2 0 ) OUT A = 4 x COMPOUT - 1.5 + OUT B where COMPOUT is the voltage at Pin 13. The voltage at COMPOUT is determined by the compensation network that is fed by the input amplifier, which receives its input voltage from TEMPSET and THERMIN. Equation 20 is valid only in the linear region of the linear amplifier. OUT B has a lower limit of 0 V and an upper limit of the power supply. 4 VTEC, MAX (V) The TEC is driven with a differential voltage, allowing current to flow in either direction through the TEC. This can provide heat transfer either to or from the object being regulated without the use of a negative voltage rail. The maximum output voltage across the TEC is set by the voltage at VLIM (Pin 15). Refer to the Setting the Maximum TEC Voltage and Current section for details on this operation. With VLIM set to ground, the maximum output voltage is the power supply voltage, VDD. These extra capacitors are specified only when using FDW2520C transistors in the linear amplifier. If other transistors are used, these values may need to be adjusted. To ensure the linear amplifier is stable, the total gate-to-source capacitance for both Q3 and Q4 should be at least 2.5 nF. Refer to the transistor's data sheet for its typical gate-to-drain capacitance values. The output of the linear amplifier is proportional to the voltage at Pin 13 (COMPOUT). Because the linear amplifier operates with a gain of 14, its output will typically be at either ground or VDD if there is more than about 100 mA of current flowing through the TEC. This ensures Q3 and Q4 will not be a dominant source of power dissipation at high output currents. (18) -13- ADN8830 IL , MAX = ITEC , MAX + 0.5 x IL Inductor Selection In addition to the external transistors, the PWM amplifier requires an inductor and a capacitor at its output to filter the switched output waveform. Proper inductor selection is important to achieve the best efficiency. The duty cycle of the PWM sets the OUT A output voltage and is OUT A D= VDD where IL can be found from Equation 23 with the appropriate duty cycle calculated from Equation 22 with OUT A = VTEC, MAX. Design Example 3 (22) The average current through the inductor is equal to the TEC current. The ripple current through the inductor, IL, varies with the duty cycle and is equal to IL = VDD x D x (1 - D) L x fCLK (23) A TEC is specified with a maximum current of 1.5 A and maximum voltage of 2.5 V. The ADN8830 will be operating from a 3.3 V supply voltage with a 200 kHz clock and a 4.7 H inductor. The duty cycle of the PWM amplifier at 2.5 V is calculated to be 75.8%. Using Equation 23, the inductor ripple current is found to be 664 mA. From Equation 24, the maximum inductor current will be 1.82 A and should be considered when selecting the inductor. Notice that increasing the clock frequency to 1 MHz would reduce IL, MAX to 1.56 A. Design Example 4 where fCLK is the clock frequency as set by the resistor RFREQ at Pin 26 or an external clock frequency. Refer to the Setting the Switching Frequency section for more information. Selecting a faster switching frequency or a larger value inductor will reduce the ripple current through the inductor. The waveform of the inductor current is shown in Figure 13. INDUCTOR CURRENT (A) (24) ITEC IL Using the same TEC as above, the ADN8830 will be powered from 5.0 V instead. Here, the duty cycle is 50%, which happens to be the worst-case duty cycle for inductor current ripple. Now DIL equals 1.33 A with a 200 kHz clock, and IL, MAX is 2.83 A. Reducing the inductor ripple current is another compelling reason to operate the ADN8830 from a 3.3 V supply instead. Table II lists some inductor manufacturers and part numbers along with some key specifications. The column IMAX refers to the maximum current at which the inductor is rated to remain linear. Although higher currents can be pushed through the inductor, efficiency and ripple voltage will be dramatically degraded. This is by no means a complete list of manufacturers or inductors that can be used in the application. More information on these inductors is available at their websites. Note the trade-offs between inductor height, maximum current, and series resistance. Smaller inductors cannot handle as mueH current and therefore require higher clock speeds to reduce their ripple current. They also have higher series resistance, which can lower the overall efficiency of the ADN8830. T= 1 fCLK PWM Output Filter Requirements TIME Figure 13. Current Waveform Through Inductor It is important to select an inductor that can tolerate the maximum possible current that could pass through it. Most TECs are specified with a maximum voltage and current for proper and reliable operation. The maximum instantaneous inductor current can be found as The switching of Q1 and Q2 creates a pulse width modulated (PWM) square wave from 0 V to VDD. This square wave must be filtered sufficiently to create a steady voltage that will drive the TEC. The ripple voltage across the TEC is a function of the inductor ripple current, the L-C filter cutoff frequency, and the equivalent series resistance (ESR) of the filter capacitor. The equivalent circuit for the PWM side is given in Figure 14. Table II. Partial List of Inductors and Key Specifications Inductance (H) IMAX (A) RS, TYP (m) Height (mm) Part Number Manufacturer Website 4.7 4.7 4.7 4.7 4.7 4.7 4.7* 10 15 47 1.1 1.59 3.9 1.5 1.32 7.5 5.4 2.7 8 4.5 200 55 48 90 56 12 18 80 32 86 1 2 2.8 3 3 4.5 5.2 2.8 8 7.1 LPO1704-472M A918CY-4R7M UP2.8B-4R7 DO1608C-472 CDRH4D28 4R7 892NAS-4R7M DO3316P-472 UP2.8B-100 DO5022P-153HC DO5022P-473 Coilcraft Toko Cooper Coilcraft Sumida Toko Coilcraft Cooper Coilcraft Coilcraft www.coilcraft.com www.toko.com www.cooperet.com www.coilcraft.com www.sumida.com www.toko.com www.coilcraft.com www.cooperet.com www.coilcraft.com www.coilcraft.com *Recommend inductor in typical application circuit Figure 1. -14- REV. C ADN8830 PVDD Calculating PWM Output Ripple Voltage OUT A Although it may seem that fC can be arbitrarily lowered to reduce output ripple, the ripple voltage is also dependent on the ESR of C1, shown as R1 in Figure 14. This resistance creates a zero that turns the second-order filter into a first-order filter at high frequencies. The location of this zero is Q1 P1 R2 RL L1 OUT B VX Q2 N1 R1 C1 DENOTES PGND Z1 = Figure 14. Equivalent Circuit for PWM Amplifier and Filter In this circuit, RL is the TEC resistance, R2 is the parasitic resistance of the inductor combined with the equivalent rDS, ON of Q1 and Q2, and R1 is the ESR of C1. The voltage, VX, is the pulse-width modulated waveform that switches between PVDD and ground. This is a second-order low-pass filter with an exact cutoff frequency of fC = 1 2 R2 + RL R 1 ( + RL ) C1L1 OUT A = IL x R1 OUT A = (25) 1 C1L1 (26) 1 2RL L1 C1 REV. C fC, MIN (kHz) 0.05 0.1 0.2 0.3 0.5 > 0.707 8 4 2 1.9 1.6 1.5 for ( fCLK > Z 1) (30) VDD R1 for ( fCLK > Z 1) 4 fCLK L1 (31) Here it can be directly seen that increasing the inductor value or clock frequency will reduce the ripple. Choosing a low ESR capacitor will ensure R1 remains low. Operating from a lower supply voltage will also help reduce the output ripple voltage from the L-C filter. With a clock frequency equal to Z1 but presumably greater than fC, the worst-case output voltage ripple is (16R1 C1 f 2 OUT AMAX = VDD 2 2 CLK 32L1C1 fCLK ) for ( f +1 CLK = Z 1) (32) Which, if fCLK < Z1, can be further simplified to Using the recommended values of L1 = 4.7 H and C1 = 22 F results in a cutoff frequency of 15.7 kHz. With a TEC resistance of 2 , the damping factor is 0.12. The cutoff frequency can be decreased to lower the output voltage ripple with slower clock frequencies by increasing L1 or C1. Increasing C1 may appear to be a simpler approach as it would not increase the physical size of the inductor, but there is a potential stability danger in lowering the damping factor too far. It is recommended that remain greater than 0.05 to provide a reasonable settling time for the TEC. Increasing also makes finding the proper PID compensation easier as there is less ringing in the L-C output filter. To allow adequate phase and gain margin for the PWM amplifier, Table III should be used to find the lower limit of cutoff frequency for a given damping factor. L1 fCLK The worst-case voltage ripple occurs when the duty cycle of the PWM output is exactly 50%, or when OUT A = 0.5 VDD. As shown in Equation 31 OUT AMAX = (27) Table III. Minimum L-C Filter Cutoff Frequency vs. Damping Factor (29) VDD D (1 - D) R1 OUT AMAX This cutoff frequency should be much lower than the clock frequency to achieve adequate filtering of the switched output waveform. Also of importance is the damping factor, , of the L-C filter. Too low a damping factor will result in a longer settling time and could potentially cause stability problems for the temperature control loop. Neglecting R1 and R2 again, the damping factor is simply = (28) With a clock frequency greater than Z1, and presumably greater than fC, the output voltage ripple is Practically speaking, R1 and R2 are several tens of milliohms and are much smaller than the TEC resistance, which can be a few ohms. The cutoff frequency can be roughly approximated as 1 fC = 2 1 2R1C1 VDD 32L1C1 fCLK 2 for ( fCLK < Z 1) (33) A typical 100 F surface-mount electrolytic capacitor can have an ESR of over 100 m, pulling this zero to below 16 kHz, and resulting in an excess of ripple voltage across the TEC. Low ESR capacitors, such as ceramic or polymer aluminum capacitors, are recommended instead. Polymer aluminum capacitors can provide more bulk capacitance per unit area over ceramic ones, saving board space. Table IV shows a limited list of capacitors with their equivalent series resistances. This is by no means a complete list of all capacitor manufacturers or capacitor types that can be used in the application. The 22 F capacitor recommended has a maximum ESR of 35 m, which puts Z1 at 207 kHz. Using a 3.3 V supply with the recommended inductor and capacitor listed with a 1 MHz clock frequency will yield a worst-case ripple voltage at OUT A of about 6 mV. External FET Requirements External FETs are required for both the PWM and linear amplifiers that drive OUT A and OUT B from the ADN8830. Although it is important to select FETs that can supply the maximum current required to the TEC, they should also have a low enough resistance (rDS, ON) to prevent excessive power dissipation and improve efficiency. Other key requirements from these FET pairs are slightly different for the PWM and linear outputs. -15- ADN8830 The gate drive outputs for the PWM amplifier at P1 (Pin 21) and N1 (Pin 22) have a typical nonoverlap delay of 65 ns. This is done to ensure that one FET is completely off before the other FET is turned on, preventing current from shooting through both simultaneously. Bear in mind that the addition of these capacitors is only for local stabilization. The stability of the entire TEC application may need adjustment, which should be done around the compensation amplifier. This is covered in the Compensation Loop section. The input capacitance (CISS) of the FET should not exceed 5 nF. The P1 and N1 outputs from the ADN8830 have a typical output impedance of 6 . This creates a time constant in combination with CISS of the external FETs equal to 6 CISS. To ensure shoot-through does not occur through these FETs, this time constant should remain less than 30 ns. There is one additional consideration for selecting both the linear output FETs; they must have a minimum threshold voltage (VT) of 0.6 V. Lower threshold voltages could cause shoot-through current in the linear output transistors. Table V shows the recommended FETs that can be used for the linear output in the ADN8830 application. Table V includes the appropriate external gate-to-drain capacitance (external CGD) and snubber capacitor value (CSNUB) connected from OUT B to ground that should be added to ensure local stability. Table VI shows the recommended PWM output FETs. Although other transistors can be used, these combinations have been tested and are proved stable and reliable for typical applications. The linear output from the ADN8830 uses N2 (Pin 10) and P2 (Pin 11) to drive the gates of the linear side FETs, shown as Q3 and Q4 in Figure 1. Local compensation for the linear amplifier is achieved through the gate-to-drain capacitances (CGD) of Q3 and Q4. The value of CGD, which can be determined from the data sheet, is usually referred to as CRSS, the reverse transfer capacitance. The exact CRSS value should be determined from a graph that shows capacitance versus drain-to-source voltage, using the power supply voltage as the appropriate VDS. Data sheets for these devices can be found at their respective websites: To ensure stability of the linear amplifier, the total CGD of the PMOS device, Q3, should be greater than 2.5 nF and the total CGD of the NMOS should be greater than 150 pF. External capacitance can be added around the FET to increase the effective CGD of the transistor. This is the function of C6 in the typical application schematic shown in Figure 1. If external capacitance must be added, it will generally only be required around the PMOS transistor. In the event of zero output current through the TEC, there will be no current flowing through Q3 and Q4. In this condition, these FETs will not provide any small signal gain and thus no negative feedback for the linear amplifier. This leaves only a feedforward signal path through CGD, which could cause a settling problem at OUT B. This is often seen as a small signal oscillation at OUT B, but only when the TEC is at or very near zero current. The remedy for this potential minor instability is to add capacitance from OUT B to ground. This may need to be determined empirically, but a good starting point is 1.5 times the total CGD. This is the function of C12 in Figure 1. Note that while adding more CGD around Q3 and Q4 will help to ensure stability, it could potentially increase instability in the zero current dead band region, requiring additional capacitance from OUT B to ground. Fairchild - www.fairchildsemi.com Vishay Siliconix - www.vishay.com International Rectifier - www.irf.com Calculating Power Dissipation and Efficiency The total efficiency of the ADN8830 application circuit is simply the ratio of the output power to the TEC divided by the total power delivered from the supply. The idea in minimizing power dissipation is to avoid both drawing additional power and reducing heat generated from the circuit. The dominant sources of power dissipation will include resistive losses, gate charge loss, core loss from the inductor, and the current used by the ADN8830 itself. The on-channel resistance of both the linear and PWM output FETs will affect efficiency primarily at high output currents. Because the linear amplifier operates in a high gain configuration, it will be at either ground or VDD when significant current is flowing through the TEC. In this condition, the power dissipation through the linear output FET will be PFET , LIN = rDS , ON x ITEC 2 (34) using either the rDS, ON for the NMOS or the PMOS depending on the direction of the current flow. In the typical application setup in Figure 2, if the TEC is cooling the target object, the PMOS is sourcing the current. If the TEC is heating the object, the NMOS will be sinking current. Table IV. Partial List of Capacitors and Key Specifications Value (F) ESR (m) Voltage Rating (V) Part Number Manufacturer Website 10 22* 22 22 47 68 100 60 35 35 35 25 18 95 6.3 8 8 8 6.3 8 10 NSP100M6.3D2TR ESRD220M08B NSP220M8D5TR EEFFD0K220R NSP470M6.3D2TR ESRD680M08B 594D107X_010C2T NIC Components Cornell Dubilier NIC Components Panasonic NIC Components Cornell Dubilier Vishay www.niccomp.com www.cornell-dubilier.com www.niccomp.com www.maco.panasonic.co.jp www.niccomp.com www.cornell-dubilier.com www.vishay.com *Recommend capacitor in typical application circuit Figure 1. -16- REV. C ADN8830 Although the FETs that drive OUT A alternate between Q1 and Q2 being on, they have an equivalent series resistance that is equal to a weighted average of their rDS, ON values. REQIV = D x rDS , P 1 + (1 - D ) x rDS , N 1 (35) The resistive power loss from the PWM transistors is then PFET , PWM = REQIV x ITEC 2 (36) There is also a power loss from the continuing charging and discharging of the gate capacitances on Q1 and Q2. The power dissipated due to gate charge loss (PGCL) is PGCL = 1 2 CISSVDD fCLK 2 PADN 8830 = VDD x 10 mA (37) (40) There are certainly other minor mechanisms for power dissipation in the circuit. However, a rough estimate of the total power dissipated can be found by summing the preceding power dissipation equations. Efficiency is then found by comparing the power dissipated with the required output power to the load. Efficiency = PLOAD PLOAD + PDISS , TOT (41) where PLOAD = ILOAD x VLOAD using the appropriate input capacitance (CISS) for the NMOS and PMOS. Both transistors are switching, so PGCL should be calculated for each one and will be added to find the total power dissipated from the circuit. The series resistance of the inductor, R2 from Figure 14, will also exhibit a power dissipation equal to PR2 = R2 x ITEC total current used by the ADN8830. The power dissipated from the device itself is 2 The measured efficiency of the system will likely be less than the calculated efficiency. Measuring the efficiency of the application circuit is fairly simple but must be done in an exact manner to ensure the correct numbers are being measured. Using two high current, low impedance ammeters and two voltmeters, the circuit should be set up as shown in Figure 15. (38) POWER SUPPLY Core loss from the inductor arises as a result of nonidealities of the inductor. Although this is difficult to calculate explicitly, it can be estimated as 80% of PRLS at 1 MHz switching frequencies and 50% of PRL at 100 kHz. Judging conservatively PLOSS = 0.8 x PRL VDD GND A V (39) A Finally, the power dissipated by the ADN8830 is equal to the current used by the device multiplied by the supply voltage. Again, this exact equation is difficult to determine as we have already taken into account some of the current while finding the gate charge loss. A reasonable estimate is to use 40 mA as the ADN8830 V TEC LOAD Figure 15. Measuring Efficiency of the ADN8830 Circuit Table V. Recommended FETs for Linear Output Amplifier Part Number Type CGD (nF) FDW2520C* NMOS PMOS NMOS PMOS NMOS PMOS 0.17 0.15 0.5 2.2 0.23 0.6 IRF7401 IRF7233 FDR6674A FDR840P Ext. CGD (nF) CSNUB (nF) 2.2 3.3 1.0 3.3 1.0 3.3 rDS, ON (m) IMAX (A) Manufacturer 18 35 22 20 9.5 12 6.0 4.5 8.7 9.5 11.5 10 Fairchild Fairchild International Rectifier International Rectifier Fairchild Fairchild *Recommend transistors in typical application circuit Figure 1. Table VI. Recommended FETs for PWM Output Amplifier Part Number Type CISS (nF) rDS,ON (m) Continuous IMAX (A) Manufacturer FDW2520C* NMOS PMOS NMOS PMOS NMOS PMOS 1.33 1.33 1.0 3.5 1.6 1.5 18 35 30 17 22 40 6.0 4.5 5.3 7.3 8.7 6.7 Fairchild Fairchild Vishay Siliconix Vishay Siliconix International Rectifier International Rectifier Si7904DN Si7401DN IRF7401 IRF7404 *Recommend transistors in typical application circuit Figure 1. REV. C -17- ADN8830 The voltmeter to the TEC or output load should include the series ammeter since the power delivered to the ammeter is considered part of the total output power. However, the voltmeter measuring the voltage delivered to the ADN8830 circuit should not include the series ammeter from the power supply. This prevents a false supply voltage power measurement since we are interested only in the supply voltage power delivered to the ADN8830 circuit. Figures 16 and 17 show some efficiency measurements using the typical application circuit shown in Figure 1. POWER SUPPLY VDD AVDD NOISE SENSITIVE SECTION VSY = 3V EFFICIENCY (%) OUTPUT SECTION PVDD TEC OR LOAD The low noise power and ground are referred to as AVDD and AGND, with the output supply and ground paths labeled PVDD and PGND. These pins are labeled on the ADN8830 and should be connected appropriately. Both sets of external FETs should be connected to PVDD and PGND. All output filtering and PVDD supply bypass capacitors should be connected to PGND. 80 VSY = 5V 60 40 20 0 500 PGND Figure 18. Using Star Connections to Minimize Noise Pickup from Switched Output 100 0 AGND GND 1,000 ITEC (mA) 1,500 2,000 Figure 16. Efficiency with fCLK = 1 MHz All remaining connections to ground and power supply should be done through AVDD and AGND. A 4-layer board layout is recommended for best performance with split power and ground planes between the top and bottom layers. This provides the lowest impedance for both supply and ground points. Setting the ADN8830 above the AGND plane will reduce the potential noise injection into the device. Figure 19 shows the top layer of the layout used for the ADN8830 evaluation boards, highlighting the power and ground split planes. 100 VSY = 3V 80 EFFICIENCY (%) VSY = 5V 60 40 20 0 0 500 1,000 ITEC (mA) 1,500 2,000 Figure 17. Efficiency with fCLK = 200 kHz Note that higher efficiency can be achieved using a lower supply voltage or a slower clock frequency. This is due to the fact that the dominant source of power dissipation at high clock frequencies is the gate charge loss on the PWM transistors. Layout Considerations The two key considerations for laying out the board for the ADN8830 are to minimize both the series resistance in the output and the potential noise pickup in the precision input section. The best way to accomplish both of these objectives is to divide the layout into two sections, one for the output components and the other for the remainder of the circuit. These sections should have independent power supply and ground current paths that are each connected together at a single point near the power supply. This is used to minimize power supply and ground voltage bounce on the more sensitive input stages to the ADN8830 caused by the switching of the PWM output. Such a layout technique is referred to as a "star" ground and supply connection. Figure 18 shows a block diagram of the concept. Figure 19. Top Layer Reference Layout for ADN8830 Proper supply voltage bypassing should also be taken into consideration to minimize the ripple voltage on the power supply. A minimum bypass capacitance of 10 F should be placed in close proximity to each component connected to the power supply. This includes Pins 8 and 20 on the ADN8830 and both external PMOS transistors. An additional 0.1 F capacitor should be placed in parallel to each 10 F capacitor to provide bypass for high frequency noise. Using a large bulk capacitor, 100 F or greater, in parallel with a low ESR capacitor where AVDD and PVDD connect will further improve voltage supply ripple. This is covered in more detail in the Power Supply Ripple section. -18- REV. C ADN8830 Power Supply Ripple Minimizing ripple on the power supply voltage can be an important consideration, particularly in signal source laser applications. If the laser diode is operated from the same supply rail as the TEC controller, ripple on the supply voltage could cause inadvertent modulation of the laser frequency. As most laser diodes are driven from a 5 V supply, it is recommended the ADN8830 be operated from a separate 3.3 V regulated supply unless higher TEC voltages are required. Operation from 3.3 V also improves efficiency, thus minimizing power dissipation. The power supply ripple is primarily a function of the supply bypass capacitance, also called bulk capacitance, and the inductor ripple current. Similar to the L-C filter at the PWM amplifier output, using more capacitance with low equivalent series resistance (ESR) will lower the supply ripple. A larger inductor value will reduce the inductor ripple current, but this may not be practical in the application. A recommended approach is to use a standard electrolytic capacitor in parallel with a low ESR capacitor. A surface-mount 220 F electrolytic in parallel with a 22 F polymer aluminum low ESR capacitor can occupy an approximate total board area of only 0.94 square inches or 61 square millimeters. Using these capacitors along with a 4.7 H inductor can yield a supply ripple of less than 5 mV. High frequency transient spikes may appear on the supply voltage as well. This is due to the fast switching times on the PWM transistors and the sharp edges of their gate voltages. Although these transient spikes can reach several tens of millivolts at their peak, they typically last for less than 20 ns and have a resonance greater than 100 MHz. Additional bulk capacitance will not appreciably affect the level of these spikes as such capacitance is not reactive at these frequencies. Adding 0.01 F ceramic capacitors on the supply line near the PWM PMOS transistor can reduce this switching noise. Inserting an RF inductor with a High-Q around 100 MHz in series with PVDD will also block this noise from traveling back to the power supply. Setting Maximum Output Current and Short-Circuit Protection Although the maximum output voltage can be programmed through VLIM to protect the TEC from overvoltage damage, the user may wish to protect the ADN8830 circuit from a possible short circuit at the output. Such a short could quickly damage the external FETs or even the power supply since they would attempt to drive excessive current. Figure 20 shows a simple modification that will protect the system from an output short circuit. VS TO FETS AND DECOUPLING CAPS RS 10m PVDD AVDD A 10 m resistor placed in series with the PVDD supply line creates a voltage drop proportional to the absolute value of the output current. The AD8601 is a CMOS amplifier that is configured as a comparator. As long as the voltage at its inverting input (VS) exceeds the voltage set by the resistor divider at the noninverting input (VX), the gate of Q1 will remain at ground. This leaves Q1 on, effectively connecting D1 to the positive rail and leaving the voltage on C1 at VDD. Should enough current flow through RS to drop VS below VX, Q1 will turn off and C1 will discharge through R2 down to a logic low to activate the ADN8830 shutdown. Once VS returns to a voltage greater than VX, Q1 will turn back on and C1 will charge back to VDD through R1. The shutdown and reactivation time constants are approximately SD = C1 x R1 ON = C1 x R1 (42) The shutdown time constant should be a minimum of 10 clock cycles to ensure high current switching transients do not trigger a false activation. If powered from 5 V, the circuit shown will shut down the ADN8830 should PVDD deliver over 5 A for more than 1 ms. After shutdown, the circuit will reactivate the ADN8830 in about 1 second. The voltage drop across RS is found as 2 VRS = IOUT RL RS VDD (43) where RL is the load resistance or resistance of the TEC and is the efficiency of the system. An estimate of efficiency can be calculated either from the Calculating Power Dissipation and Efficiency section or from Figures 16 and 17. A reasonable approximation is = 0.85. Although the exact resistance of a TEC varies with temperature, an estimation can be made by dividing the maximum voltage rating of the TEC by its maximum current rating. In addition to providing protection against a short at the output, this circuit will also protect the FETs against shoot-through current. Shoot-through will not occur when using the recommended transistors and additional capacitance shown in Tables V and VI. However, if different transistors are used where their shootthrough potential is unknown, implementing the short-circuit protection circuit will unconditionally protect these transistors. To set a maximum output current limit, use the circuit in Figure 21. This circuit can share the 10 m power supply shunt resistor as the short-circuit protection circuit to sense the output current. In normal operation Q1 is on, pulling the ADN8830 VLIM pin down to the voltage set by VLIMIT. This sets the maximum output voltage limit as described in the Setting the Maximum TEC Voltage and Current section. PVDD R3 1k Q1 FDV304P OR EQUIVALENT AD8601 R4 100k VX R1 1M SD R2 1k D1 MA116CT-ND OR EQUIVALENT C1 1F VSY TO FETS AND DECOUPLING PVDD CAPS R3 178 PVDD AVDD R1 3.48k AD8605 R4 100k DENOTES AGND RS 10m Q1 FDV301N OR EQUIVALENT C1 1nF TO VLIM R2 1.47k VX DENOTES PGND VLIMIT (0V TO 1.5V) Figure 20. Implementing Output Short-Circuit Protection DENOTES AGND DENOTES PGND Figure 21. Setting a Maximum Output Current Limit REV. C -19- ADN8830 5V IOUTA ADT70 IOUTB +INOA TO THERM_IN = 1V @ 25C R3 82.5 OUTOA 25mV/C +INIA RGA INST AMP 4.99k R3 82.5 RGB -INIA RTD 1k R3 1k GND SENSE AGND OUTIA -INOA 1k 5.11k NOTE: ADDITIONAL PINS OMITTED FOR CLARITY Figure 22. Using an RTD for Temperature Feedback to the ADN8830 If the voltage at VSY drops below VX, Q1 is turned off and the VLIM pin will be set to 1.5 V, effectively setting the maximum voltage across the outputs to 0 V. The voltage divider for VX is calculated from Equation 43. TO TEC AVDD RS 10m TO OUT B IL AVDD AVDD R1 3.48k 200k VHI TO VLIM R2 1.47k 1nF 300k Design Example 5 A maximum output current limit needs to be set at 1.5 A for a TEC with a maximum voltage rating of 2.5 V. The ADN8830 is powered from 5 V. The TEC resistance is estimated at 1.67 and efficiency at 85%. Using Equation 43, the voltage drop across RS will be 8.8 mV when 1.5 A is delivered to the TEC. The trip voltage VX is set to 4.991 V with R3 = 178 and R4 = 100 k as shown in Figure 21. To set the output voltage limit to 2.5 V, the voltage at VLIMIT should be set to 0.875 V according to Equation 17. 8 AD626 VX AD8602 Q1,Q2 FDG6303N OR EQUIVALENT 300k TO VREF VLO 200k VLIMIT (0V TO 1.5V) Figure 23. High Accuracy Output Current Limit The C1 capacitor is added to smooth the voltage transitions at VLIM. Once an overcurrent condition is detected, the output voltage will turn down to 0 V within 30 ms. For a more exact measurement of the output current, place a sense resistor in series with the output load, as shown in Figure 23. The AD626 instrumentation amplifier is set for a gain of 100 with a reference voltage of 2.47 V from VREF. The output of the AD626 is equal to 100 x RS x IL and is fed to the AD8602, which is set up as a window comparator. With VX greater than VLO but less than VHI, VLIM will be pulled down to the voltage at VLIMIT. Should VX fall outside the voltage window, VLIM will be pulled to 1.5 V as in Figure 21. The trip points should be set according to VHI = VREF + 100 x RS I LIMIT + VLO = VREF - 100 x RS I LIMIT - AVDD The upper and lower trip point voltages can be set independently, allowing different maximum output current limits depending on the direction of the current. The resistor divider for VHI and VLO is tapped to VREF to maintain window accuracy with any changes in VREF. Using the values from Figure 23 with a 5 V supply, the output current will not exceed 1.5 A in either direction. Adding the current sensing resistor will slightly reduce efficiency. The power dissipated by this resistor is D x ITEC2 x RS if the TEC is heating, or (1-D) x ITEC2 x RS if the TEC is cooling. Include this when calculating efficiency as described in the Calculating Power Dissipation and Efficiency section. (44) -20- REV. C ADN8830 PVDD Using an RTD for Temperature Sensing The ADN8830 can be used with a resistive temperature device (RTD) as the temperature feedback sensor. The resistance of an RTD is linear with respect to temperature, offering an advantage over thermistors that have an exponential relationship to temperature. A constant current applied through an RTD will yield a voltage proportional to temperature. However, this voltage could be on the order of only 0.5 mV/C, thus requiring the use of additional amplification to achieve a usable signal level. The ADT70 from Analog Devices can be used to bias and amplify the voltage across an RTD, which can then be fed directly to the THERMIN pin on the ADN8830 to provide temperature feedback for the TEC controller. The ADT70 uses a 0.9 mA current source to drive the RTD and an instrumentation amplifier with adjustable gain to boost the RTD voltage. Application notes and typical schematics for this device can be found in the ADT70 Data Sheet. Most RTDs have a positive temperature coefficient, also called tempco, as opposed to thermistors, which have a negative tempco. For the OUT A output to drive the TEC- input as shown in Figure 1, the signal from an RTD must be conditioned to create a negative tempco. This can be easily done using an inverting amplifier. Alternately, OUT A can be connected to drive TEC+ with OUT B driving TEC- with a positive tempco at THERMIN. This is highlighted in the Output Driver Amplifiers section. For the ADN8830, proper operation care should be taken to ensure the voltage at THERMIN remains within 0.4 V and 2.0 V. Using a 1 k RTD with the ADT70 will yield a THERMIN voltage of 0.9 V at 25C. Using the application circuit shown in Figure 22 will provide a nominal output voltage of 1.0 V at 25C and a total gain of 66.7 mV/. Using an RTD with a temperature coefficient of 0.375 /C will give a THERMIN voltage swing from 1.5 V at 5C to 0.5 V at 45C, well within the input range of the ADN8830. OUT A Q1 P1 L1 RL OUT B Q2 N1 C1 Q3 N2 NO CONNECTION TO P2 REQUIRED Figure 24. Using the ADN8830 to Drive a Heating Element Current is delivered from the PWM amplifier through Q3 when the voltage at THERMIN is lower than TEMPSET. If the object temperature is greater than the target temperature, Q3 will turn off and the current through the load goes to zero, allowing the object to cool back toward the ambient temperature. As the target temperature is approached, a steady output current should be reached. Naturally, a proper compensation network must be found to ensure stability and adequate temperature settling time. The P2 output from the ADN8830 should be left unconnected. Suggested Pad Layout for CP-32 Package Figure 25 shows the dimensions for the PC board pad layout for the ADN8830, which is a 5 5, 32-lead lead frame chipscale package. This package has a metallic heat slug that should be soldered to a copper pad on the PC board. Although the package slug is electrically connected to the substrate of the IC, the copper pad should be left electrically floating. This prevents potential noise injection into the substrate while maintaining good thermal conduction to the PC board. 0.69 (0.0272) 0.10 (0.0039) Using a Resistive Load as a Heating Element The ADN8830 can be used in applications that do not necessarily drive a TEC but require only a high current output into a load resistance. Such applications generally only require heating above ambient temperature and simply use the power dissipated by the load element to accomplish this. Because the power dissipated by such an element is proportional to the square of the output voltage, the ADN8830 application circuit must be modified. Figure 24 shows the preferred method for driving a heating element load. 5.36 (0.2110) 0.28 (0.0110) 3.78 (0.1488) 0.50 (0.0197) 3.68 (0.1449) PACKAGE OUTLINE CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN THERMAL PAD SHOULD BE SOLDERED TO AN ELECTRICALLY FLOATING PAD ON THE PC BOARD Figure 25. Suggested PC Board Layout for CP-32 Pad Landing REV. C -21- ADN8830 OUTLINE DIMENSIONS 32-Lead Lead Frame Chip Scale Package [LFCSP] (CP-32-1) Dimensions shown in millimeters 5.00 BSC SQ 0.60 MAX 25 24 PIN 1 INDICATOR 3.25 3.10 SQ 2.95 BOTTOM VIEW 0.50 0.40 0.30 12 MAX 32 1 0.50 BSC 4.75 BSC SQ TOP VIEW 1.00 0.85 0.80 PIN 1 INDICATOR 0.60 MAX 17 16 9 8 0.25 MIN 3.50 REF 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM SEATING PLANE 0.30 0.23 0.18 0.20 REF COPLANARITY 0.08 COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2 -22- REV. C ADN8830 Revision History Location Page 11/03--Data Sheet Changed from REV. B to REV. C. Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Deleted Figure 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Deleted Boosting the Output Voltage section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Deleted Figure 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Deleted Equations 45, 46 and 47 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8/03--Data Sheet Changed from REV. A to REV. B. Updated ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Updated Thermistor Setup section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2/03--Data Sheet changed from REV. 0 to REV. A. Renumbered Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal Change to Thermistor Setup section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Change to Figure 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Change to Figure 23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Change to Figure 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Update OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 REV. C -23- -24- C02793-0-11/03(C)