SMT POWER INDUCTORS Power Beads - PA2202.XXXNL Series Current Rating: Over 75Apk Inductance Range: 120nH to 360nH Height: 6.0mm Max Footprint: 12.1mm x 10.0mm Max Electrical Specifications @ 25C -- Operating Temperature -40C to +130C 7 Inductance @0ADC (nH 15%) Inductance @Irated (nH TYP) Irated 1 (ADC) PA2202.121NL 120 120 36 PA2202.181NL 180 180 36 144 117 64 52 PA2202.211NL 215 215 36 172 140 53 47 PA2202.231NL 230 230 36 184 150 47 44 PA2202.321NL 325 282 31 260 211 34 31 PA2202.361NL 365 315 27 292 237 30 27 DCR 2 (m) 0.48 6.5% NOTES: 1. The rated current as listed is either the saturation current or the heating current depending on which value is lower. 2. The nominal DCR is measured from point a to point b , as shown below on the mechanical drawing. 3. The saturation current is the typical current which causes the inductance to drop by 20% at the stated ambient temperatures (25C and 100C). Inductance at Isat is the minimum inductance when measured at Isat (25C and 100C).This current is determined by placing the component in the specified ambient environment and applying a short duration pulse current (to eliminate self-heating effects) to the component. 4. The heating current is the DC current which causes the part temperature to increase by approximately 40C. This current is determined by solder- Inductance @Isat (nH TYP) Inductance @Isat (nH MIN) 96 78 Saturation Current 3 (A TYP) 25C 100C Part Number PA2202.XXXNL D/C MFG. 75 36 ing the component on a typical application PCB, and then applying the current to the device for 30 minutes. 5. In high volt*time applications, additional heating in the component can occur due to core losses in the inductor which may neccessitate derating the current in order to limit the temperature rise of the component. To determine the approximate total losses (or temperature rise) for a given application, the coreloss and temperature rise curves can be used. 6. Optional Tape & Reel packaging can be ordered by adding a "T" suffix to the part number (i.e. PA2202.121NL becomes PA2202.121NLT). Pulse complies to industry standard tape and reel specification EIA481. 7. The temperature of the component (ambient plus temperature rise) must be within the stated operating temperature range. Mechanical .476 MAX 12,10 84 Heating 4 Current (A TYP) Schematic .140 3,56 .394 10,00 MAX 1 .175 4,45 2 .345 8,76 SUGGESTED PAD LAYOUT .250 6,35 .236 6,00 MAX a b 2X .100 2,54 Weight . . . . . . . . . . .2.7 grams Tape & Reel . . . . . . . .600/reel .155 3,94 Dimensions: Inches mm Unless otherwise specified, all tolerances are .010 0,25 .486 12,35 TAPE & REEL LAYOUT .945 24,00 .402 10,20 .630 16,00 USER DIRECTION OF FEED USA 858 674 8100 * Germany 49 7032 7806 0 * Singapore 65 6287 8998 * Shanghai 86 21 32181071 * China 86 755 33966678 * Taiwan 886 3 4643715 www.pulseeng.com P664.A (8/08) SMT POWER INDUCTORS Power Beads - PA2202.XXXNL Series Typical Inducance vs DC Bias @ 25C 400 .361NL Inductance (nH) 350 .321NL 300 250 .231NL .211NL 200 .181NL 150 .121NL 100 50 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 65 70 75 DC Bias (A) Typical Inducance vs DC Bias @ 100C 400 .361NL Inductance (nH) 350 .321NL 300 250 .231NL .211NL 200 .181NL 150 .121NL 100 50 0 5 10 15 25 30 500 kHz 0.5 400 kHz 600 kHz 0.4 300 kHz 700 kHz 0.3 1.0 MHz 200 kHz 0.2 0.1 0.0 0 500 1000 1500 2000 DB where DB = 0.32 * L(nH) * DI 2500 35 40 DC Bias (A) CoreLoss (W) 0.6 CoreLoss (W) 20 3000 Temp Rise above Ambient (C) (Trise = 57.6 * Total Power Dissipation.833) 0 45 50 55 60 Temp Rise vs Power Dissipation 110 100 90 80 70 60 50 40 30 20 10 0 0 0.2 0.4 0.6 0.8 1.0 1.4 1.6 1.2 Total Power Dissipation (W) = CopperLoss + CoreLoss 2 CopperLoss = Irms * Rdc(mW) / 1000 CoreLoss = (from table) 1.8 For More Information: Pulse Worldwide Headquarters Pulse European Headquarters Pulse China Headquarters 12220 World Trade Dr. San Diego, CA 92128 U.S.A. www.pulseeng.com Einsteinstrasse 1 D-71083 Herrenberg Germany TEL: 858 674 8100 FAX: 858 674 8262 TEL: 49 7032 7806 0 FAX: 49 7032 7806 12 B402, Shenzhen Academy of Aerospace Technology Bldg. 10th Kejinan Rd. High-Tech Zone Nanshan District Shenzen, PR China 518057 TEL: 86 755 33966678 FAX: 86 755 33966700 Pulse North China Pulse South Asia Pulse North Asia Room 1503 XinYin Building No. 888 YiShan Rd. Shanghai 200233 China 150 Kampong Ampat #07-01/02 KA Centre Singapore 368324 No. 26 Kao Ching Rd. Yang Mei Chen Taoyuan Hsien Taiwan, R. O. C. 32667 TEL: 86 21 32181071 FAX: 86 21 32181396 TEL: 65 6287 8998 FAX: 65 6280 0080 TEL: 886 3 4643715 FAX: 886 3 4641911 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. (c) Copyright, 2008. Pulse Engineering, Inc. All rights reserved. www.pulseeng.com P664.A (8/08)