DS1302
Trickle-Charge Timekeeping Chip
1 of 13 REV: 120208
FEATURES
Real-Time Clock Counts Seconds, Minute s,
Hours, Date of the Month, Month, Day of the
Week, and Year with Leap-Year
Compensation Valid Up to 2100
31 x 8 Battery-Backed General-Purpose RAM
Serial I/O for Minimum Pin Count
2.0V to 5.5V Full Operation
Uses Less than 300nA at 2.0V
Single-Byte or Multiple-Byte (Burst Mode)
Data Transfer for Read or Write of Clock or
RAM Data
8-Pin DIP or Optional 8-Pin SO for Surface
Mount
Simple 3-Wire Interface
TTL-Compatible (VCC = 5V)
Optional Industrial Temperature Range:
-40°C to +85 °C
DS1202 Compatible
Underwriters Laboratori es (UL®)
Recognized
PIN CONFIGURATIONS
ORDERING INFORMATION
PART TEMP RANGE PIN-PACKAGE TOP MARK*
DS1302+ 0°C to +70°C 8 PDIP (300 mils) DS1302
DS1302N+ -40°C to +85°C 8 PDIP (300 mils) DS1302
DS1302S+ 0°C to +70°C 8 SO (208 mils) DS1302S
DS1302SN+ -40°C to +85°C 8 SO (208 mils) DS1302S
DS1302Z+ 0°C to +70°C 8 SO (150 mils) DS1302Z
DS1302ZN+ -40°C to +85°C 8 SO (150 mils) DS1302ZN
+Denotes a lead-free/RoHS-compliant package.
*An N anywhere on the top mark indicates an industrial temperature grade device. A + anywhere on the top mark indicates a lead-free device.
UL is a registered trademark of Underwriters Laboratories, Inc.
www.maxim-ic.com
VCC1
SCLK
I/O
CE
VCC2
X1
X2
GND
8
7
6
5
1
2
3
4
DIP (300 mils)
DS1302
VCC2
X1
X2
GND
VCC1
SCLK
I/O
CE
8
7
6
5
1
2
3
4
SO (208 mils/150 mils)
DS1302
TOP VIEW
DS1302 Trickle-Charge Timekeeping Chip
2 of 13
DETAILED DESCRIPTION
The DS1302 trickle-charge timekeeping chip contains a real-time clock/calendar and 31 bytes of static RAM. It
communicates with a microprocessor via a simple serial interface. The real-time clock/calendar provides seconds,
minutes, hours, day, date, month, and year information. The end of the month date is automatically adjusted for
months with fewer than 31 days, including corrections for leap year. The clock operates in either the 24-hour or
12-hour format with an AM/PM indicator.
Interfacing the DS1302 with a microprocessor is simplified by using synchronous serial communication. Only three
wires are required to communicate with the clock/RAM: CE, I/O (data line), and SCLK (serial clock). Data can be
transferred to and from the clock/RAM 1 byte at a time or in a burst of up to 31 bytes. The DS1302 is designed to
operate on very low power and retain data and clock information on less than 1μW.
The DS1302 is the successor to the DS1202. In addition to the basic timekeeping functions of the DS1202, the
DS1302 has the additional features of dual power pins for primary and backup power supplies, programmable
trickle charger for VCC1, and seven additional bytes of scratchpad memory.
OPERATION
Figure 1 shows the main elements of the serial timekeeper: shift register, control logic, oscillator, real-time clock,
and RAM.
TYPICAL OPERATING CIRCUIT
DS1302
CPU
VCC
V
CC2
SCLK
CE
GND
X2 X1
VCC
I/O
V
CC1
DS1302 Trickle-Charge Timekeeping Chip
3 of 13
Figure 1. Block Diagram
POWER
CONTROL
v
CC1
v
CC2
GND
INPUT SHIFT
REGISTERS
I/O
SCLK
COMMAND AND
CONTROL LOGIC
REAL TIME
CLOCK
31 X 8 RAM
X1X2
CE
1Hz
C
L
C
L
DS1302
TYPICAL OPERATING CHARACTERISTICS
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
ICC2T vs. VCC2T
5
10
15
20
25
30
2.03.04.05.0
VCC2 (V)
SUPPLY CURRENT (uA
)
ICC1T vs. VCC1T
100
150
200
250
300
350
400
2.0 3.0 4.0 5.0
VCC1 (V)
SUPPLY CURRENT (nA
)
DS1302 Trickle-Charge Timekeeping Chip
4 of 13
PIN DESCRIPTION
PIN NAME FUNCTION
1 VCC2
Primary Power-Supply Pin in Dual Supply Configuration. VCC1 is connected to a
backup source to maintain the time and date in the absence of primary power. The
DS1302 operates from the larger of VCC1 or VCC2. When VCC2 is greater than VCC1 +
0.2V, VCC2 powers the DS1302. When VCC2 is less than VCC1, VCC1 powers the
DS1302.
2 X1
3 X2
Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator is
designed for operation with a crystal having a specified load capacitance of 6pF.
For more information on crystal selection and crystal layout considerations, refer to
Application Note 58: Crystal Considerations for Dallas Real-Time Clocks. The
DS1302 can also be driven by an external 32.768kHz oscillator. In this
configuration, the X1 pin is connected to the external oscillator signal and the X2 pin
is floated.
4 GND Ground
5 CE
Input. CE signal must be asserted high during a read or a write. This pin has an
internal 40kΩ (typ) pulldown resistor to ground. Note: Previous data sheet revisions
referred to CE as RST. The functionality of the pin has not changed.
6 I/O
Input/Push-Pull Output. The I/O pin is the bidirectional data pin for the 3-wire
interface. This pin has an internal 40kΩ (typ) pulldown resistor to ground.
7 SCLK
Input. SCLK is used to synchronize data movement on the serial interface. This pin
has an internal 40kΩ (typ) pulldown resistor to ground.
8 VCC1
Low-Power Operation in Single Supply and Battery-Operated Systems and Low-
Power Battery Backup. In systems using the trickle charger, the rechargeable
energy source is connected to this pin. UL recognized to ensure against reverse
charging current when used with a lithium battery. Go to www.maxim-
ic.com/TechSupport/QA/ntrl.htm.
DS1302 Trickle-Charge Timekeeping Chip
5 of 13
OSCILLATOR CIRCUIT
The DS1302 uses an external 32.768kHz crystal. The oscillator circuit does not require any external resistors or
capacitors to operate. Table 1 specifies several crystal parameters for the external crystal. Figure 1 shows a
functional schematic of the oscillator circuit. If using a crystal with the specified characteristics, the startup time is
usually less than one second.
CLOCK ACCURACY
The accuracy of the clock is dependent upon the accuracy of the crystal and the accuracy of the match between
the capacitive load of the oscillator circuit and the capacitive load for which the crystal was trimmed. Additional
error will be added by crystal frequency drift caused by temperature shifts. External circuit noise coupled into the
oscillator circuit may result in the clock running fast. Figure 2 shows a typical PC board layout for isolating the
crystal and oscillator from noise. Refer to Application Note 58: Crystal Considerations for Dallas Real-Time Clocks
for detailed information.
Table 1. Crystal Specifications*
PARAMETER SYMBOL MIN TYP MAX UNITS
Nominal Frequency fO 32.768 kHz
Series Resistance ESR 45 kΩ
Load Capacitance CL 6 pF
*The crystal, traces, and crystal input pins should be isolated from RF generating signals. Refer to
Application Note 58: Crystal Considerations for Dallas Real-Time Clocks for additional specifications.
Figure 2. Typical PC Board Layout for Crystal
LOCAL GROUND PLANE (LAYER 2)
CRYSTAL
X1
X2
GND
NOTE:
A
VOID ROUTING SIGNALS IN THE
CROSSHATCHED AREA (UPPER LEFT-
HAND QUADRANT) OF THE PACKAGE
UNLESS THERE IS A GROUND PLANE
BETWEEN THE SIGNAL LINE AND THE
PACKAGE.
COMMAND BYTE
Figure 3 shows the command byte. A command byte initiates each data transfer. The MSB (bit 7) must be a logic
1. If it is 0, writes to the DS1302 will be disabled. Bit 6 specifies clock/calendar data if logic 0 or RAM data if logic 1.
Bits 1 to 5 specify the designated registers to be input or output, and the LSB (bit 0) specifies a write operation
(input) if logic 0 or read operation (output) if logic 1. The command byte is always input starting with the LSB (bit 0).
Figure 3. Address/Command Byte
1RAM
CK A4 A3 A2 A1 A0 RD
WR
76543210
DS1302 Trickle-Charge Timekeeping Chip
6 of 13
CE AND CLOCK CONTROL
Driving the CE input high initiates all data transfers. The CE input serves two functions. First, CE turns on the
control logic that allows access to the shift register for the address/command sequence. Second, the CE signal
provides a method of terminating either single-byte or multiple-byte CE data transfer.
A clock cycle is a sequence of a rising edge followed by a falling edge. For data inputs, data must be valid during
the rising edge of the clock and data bits are output on the falling edge of clock. If the CE input is low, all data
transfer terminates and the I/O pin goes to a high-impedance state. Figure 4 shows data transfer. At power-up, CE
must be a logic 0 until VCC > 2.0V. Also, SCLK must be at a logic 0 when CE is driven to a logic 1 state.
DATA INPUT
Following the eight SCLK cycles that input a write command byte, a data byte is input on the rising edge of the next
eight SCLK cycles. Additional SCLK cycles are ignored should they inadvertently occur. Data is input starting with
bit 0.
DATA OUTPUT
Following the eight SCLK cycles that input a read command byte, a data byte is output on the falling edge of the
next eight SCLK cycles. Note that the first data bit to be transmitted occurs on the first falling edge after the last bit
of the command byte is written. Additional SCLK cycles retransmit the data bytes should they inadvertently occur
so long as CE remains high. This operation permits continuous burst mode read capability. Also, the I/O pin is tri-
stated upon each rising edge of SCLK. Data is output starting with bit 0.
BURST MODE
Burst mode can be specified for either the clock/calendar or the RAM registers by addressing location 31 decimal
(address/command bits 1 through 5 = logic 1). As before, bit 6 specifies clock or RAM and bit 0 specifies read or
write. There is no data storage capacity at locations 9 through 31 in the Clock/Calendar Registers or location 31 in
the RAM registers. Reads or writes in burst mode start with bit 0 of address 0.
When writing to the clock registers in the burst mode, the first eight registers must be written in order for the data to
be transferred. However, when writing to RAM in burst mode it is not necessary to write all 31 bytes for the data to
transfer. Each byte that is written to will be transferred to RAM regardless of whether all 31 bytes are written or not.
CLOCK/CALENDAR
The time and calendar information is obtained by reading the appropriate register bytes. Table 3 illustrates the RTC
registers. The time and calendar are set or initialized by writing the appropriate register bytes. The contents of the
time and calendar registers are in the binary-coded decimal (BCD) format.
The day-of-week register increments at midnight. Values that correspond to the day of week are user-defined but
must be sequential (i.e., if 1 equals Sunday, then 2 equals Monday, and so on.). Illogical time and date entries
result in undefined operation.
When reading or writing the time and date registers, secondary (user) buffers are used to prevent errors when the
internal registers update. When reading the time and date registers, the user buffers are synchronized to the
internal registers the rising edge of CE.
The countdown chain is reset whenever the seconds register is written. Write transfers occur on the falling edge of
CE. To avoid rollover issues, once the countdown chain is reset, the remaining time and date registers must be
written within 1 second.
The DS1302 can be run in either 12-hour or 24-hour mode. Bit 7 of the hours register is defined as the 12- or 24-
hour mode-select bit. When high, the 12-hour mode is selected. In the 12-hour mode, bit 5 is the AM/PM bit with
logic high being PM. In the 24-hour mode, bit 5 is the second 10-hour bit (20–23 hours). The hours data must be
re-initialized whenever the 12/24 bit is changed.
DS1302 Trickle-Charge Timekeeping Chip
7 of 13
CLOCK HALT FLAG
Bit 7 of the seconds register is defined as the clock halt (CH) flag. When this bit is set to logic 1, the clock oscillator
is stopped and the DS1302 is placed into a low-power standby mode with a current drain of less than 100nA. When
this bit is written to logic 0, the clock will start. The initial power-on state is not defined.
WRITE-PROTECT BIT
Bit 7 of the control register is the write-protect bit. The first seven bits (bits 0 to 6) are forced to 0 and always read 0
when read. Before any write operation to the clock or RAM, bit 7 must be 0. When high, the write-protect bit
prevents a write operation to any other register. The initial power-on state is not defined. Therefore, the WP bit
should be cleared before attempting to write to the device.
TRICKLE-CHARGE REGISTER
This register controls the trickle-charge characteristics of the DS1302. The simplified schematic of Figure 5 shows
the basic components of the trickle charger. The trickle-charge select (TCS) bits (bits 4 to 7) control the selection of
the trickle charger. To prevent accidental enabling, only a pattern of 1010 enables the trickle charger. All other
patterns will disable the trickle charger. The DS1302 powers up with the trickle charger disabled. The diode select
(DS) bits (bits 2 and 3) select whether one diode or two diodes are connected between VCC2 and VCC1. If DS is 01,
one diode is selected or if DS is 10, two diodes are selected. If DS is 00 or 11, the trickle charger is disabled
independently of TCS. The RS bits (bits 0 and 1) select the resistor that is connected between VCC2 and VCC1. The
resistor and diodes are selected by the RS and DS bits as shown in Table 2.
Table 2. Trickle Charger Resistor and Diode Select
TCS
BIT 7
TCS
BIT 6
TCS
BIT 5
TCS
BIT 4
DS
BIT 3
DS
BIT 2
RS
BIT 1
RS
BIT 0 FUNCTION
X X X X X X 0 0 Disabled
X X X X 0 0 X X Disabled
X X X X 1 1 X X Disabled
1 0 1 0 0 1 0 1 1 Diode, 2kΩ
1 0 1 0 0 1 1 0 1 Diode, 4kΩ
1 0 1 0 0 1 1 1 1 Diode, 8kΩ
1 0 1 0 1 0 0 1 2 Diodes, 2kΩ
1 0 1 0 1 0 1 0 2 Diodes, 4kΩ
1 0 1 0 1 0 1 1 2 Diodes, 8kΩ
0 1 0 1 1 1 0 0 Initial power-on state
Diode and resistor selection is determined by the user according to the maximum current desired for battery or
super cap charging. The maximum charging current can be calculated as illustrated in the following example.
Assume that a system power supply of 5V is applied to VCC2 and a super cap is connected to VCC1. Also assume
that the trickle charger has been enabled with one diode and resistor R1 between VCC2 and VCC1. The maximum
current IMAX would therefore be calculated as follows:
IMAX = (5.0V – diode drop) / R1 (5.0V – 0.7V) / 2kΩ 2.2mA
As the super cap charges, the voltage drop between VCC2 and VCC1 decreases and therefore the charge current
decreases.
DS1302 Trickle-Charge Timekeeping Chip
8 of 13
CLOCK/CALENDAR BURST MODE
The clock/calendar command byte specifies burst mode operation. In this mode, the first eight clock/calendar
registers can be consecutively read or written (see Table 3) starting with bit 0 of address 0.
If the write-protect bit is set high when a write clock/calendar burst mode is specified, no data transfer will occur to
any of the eight clock/calendar registers (this includes the control register). The trickle charger is not accessible in
burst mode.
At the beginning of a clock burst read, the current time is transferred to a second set of registers. The time
information is read from these secondary registers, while the clock may continue to run. This eliminates the need to
re-read the registers in case of an update of the main registers during a read.
RAM
The static RAM is 31 x 8 bytes addressed consecutively in the RAM address space.
RAM BURST MODE
The RAM command byte specifies burst mode operation. In this mode, the 31 RAM registers can be consecutively
read or written (see Table 3) starting with bit 0 of address 0.
REGISTER SUMMARY
A register data format summary is shown in Table 3.
CRYSTAL SELECTION
A 32.768kHz crystal can be directly connected to the DS1302 via pins 2 and 3 (X1, X2). The crystal selected for
use should have a specified load capacitance (CL) of 6pF. For more information on crystal selection and crystal
layout consideration, refer to Application Note 58: Crystal Considerations for Dallas Real-Time Clocks.
Figure 4. Data Transfer Summary
A1 A2 A3 A4 R/C1
CE
SCLK
I/O R/WA0 D1 D2 D3 D4 D5 D6 D7D0
SINGLE-BYTE READ
A1 A2 A3 A4 R/C1
CE
SCLK
I/O R/WA0 D1 D2 D3 D4 D5 D6 D7D0
SINGLE-BYTE WRITE
NOTE: IN BURST MODE, CE IS KEPT HIGH AND ADDITIONAL SCLK CYCLES ARE SENT UNTIL THE END OF THE BURST.
DS1302 Trickle-Charge Timekeeping Chip
9 of 13
Table 3. Register Address/Definition
RTC
READ WRITE BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 RANGE
81h 80h CH 10 Seconds Seconds 00–59
83h 82h 10 Minutes Minutes 00–59
10
85h 84h
12/24 0 AM/PM Hour Hour 1–12/0–23
87h 86h 0 0 10 Date Date 1–31
89h 88h 0 0 0 10
Month Month 1–12
8Bh 8Ah 0 0 0 0 0 Day 1–7
8Dh 8Ch 10 Year Year 00–99
8Fh 8Eh WP 0 0 0 0 0 0 0
91h 90h TCS TCS TCS TCS DS DS RS RS
CLOCK BURST
BFh BEh
RAM
C1h C0h 00-FFh
C3h C2h 00-FFh
C5h C4h 00-FFh
.
.
.
.
.
.
.
.
.
FDh FCh 00-FFh
RAM BURST
FFh FEh
Figure 5. Programmable Trickle Charger
2KΩ
4kΩ
8kΩ
R1
R3
R2
VCC2 VCC1
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
TCS3 TCS2 TCS1 TCS0 DS1 DS0 ROUT1 ROUT0
TRICKLE CHARGE REG ISTER (90h write, 91h read)
1 0F 16 SELECT
NOTE: ONLY 1010b ENABLES CHARGER
1 OF 2
SELECT
1 OF 3
SELECT
TCS0-3 = TRICKLE CHARGER SELECT
DS0-1 = DIODE SELECT
ROUT0-1 = RESISTOR SELECT
DS1302 Trickle-Charge Timekeeping Chip
10 of 13
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Pin Relative to Ground……………………………………………………………….-0.5Vto +7.0V
Operating Temperature Range, Commercial………………………………………………………………….0°C to +70°C
Operating Temperature Range, Industrial (IND)……………………………………………………………-40°C to +85°C
Storage Temperature Range……………………………………………………………………………..….-55°C to +125°C
Soldering Temperature (leads, 10 seconds)………………………………………………………………..………….260°C
Soldering Temperature (surface mount)………………………………………………..…….See IPC/JEDEC J-STD-020
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond thos e indicated in the operational sections of the specifications is
not implied. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability.
RECOMMENDED DC OPERATING CONDITIONS
(TA = 0°C to +70°C or TA = -40°C to +85°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Supply Voltage VCC1, VCC2 VCC1,
VCC2 (Notes 2, 10) 2.0 3.3 5.5 V
Logic 1 Input VIH (Note 2) 2.0 VCC +
0.3 V
VCC = 2.0V -0.3 +0.3
Logic 0 Input VIL VCC = 5V (Note 2) -0.3 +0.8 V
DC ELECTRICAL CHARACTERISTICS
(TA = 0°C to +70°C or TA = -40°C to +85°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Input Leakage ILI (Notes 5, 13) 85 500 μA
I/O Leakage ILO (Notes 5, 13) 85 500 μA
Logic 1 Output (IOH = -0.4mA) VCC = 2.0V 1.6
Logic 1 Output (IOH = -1.0mA) VOH VCC = 5V (Note 2) 2.4 V
Logic 0 Output (IOL = 1.5mA) VCC = 2.0V 0.4
Logic 0 Output (IOL = 4.0mA) VOL VCC = 5V (Note 2) 0.4
V
VCC1 = 2.0V 0.4
Active Supply Current
(Oscillator Enabled) ICC1A VCC1 = 5V
CH = 0
(Notes 4, 11) 1.2
mA
VCC1 = 2.0V 0.2 0.3
Timekeeping Current
(Oscillator Enabled) ICC1T VCC1 = 5V
CH = 0
(Notes 3, 11,13) 0.45 1 μA
VCC1 = 2.0V 1 100
VCC1 = 5V 1 100
Standby Current (Oscillator
Disabled) ICC1S
IND
CH = 1
(Notes 9, 11, 13) 5 200
nA
VCC2 = 2.0V 0.425
Active Supply Current
(Oscillator Enabled) ICC2A VCC2 = 5V
CH = 0
(Notes 4, 12) 1.28
mA
VCC2 = 2.0V 25.3
Timekeeping Current
(Oscillator Enabled) ICC2T VCC2 = 5V
CH = 0
(Notes 3, 12) 81
μA
VCC2 = 2.0V CH = 1
(Notes 9, 12) 25
Standby Current (Oscillator
Disabled) ICC2S
VCC2 = 5V 80
μA
R1 2
R2 4
Trickle-Charge Resistors
R3 8
kΩ
Trickle-Charge Diode Voltage
Drop VTD 0.7 V
DS1302 Trickle-Charge Timekeeping Chip
11 of 13
CAPACITANCE
(TA = +25°C)
PARAMETER SYMBOL MIN TYP MAX UNITS
Input Capacitance CI 10 pF
I/O Capacitance CI/O 15 pF
AC ELECTRICAL CHARACTERISTICS
(TA = 0°C to +70°C or TA = -40°C to +85°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
VCC = 2.0V 200
Data to CLK Setup tDC VCC = 5V (Note 6) 50 ns
VCC = 2.0V 280
CLK to Data Hold tCDH VCC = 5V (Note 6) 70 ns
VCC = 2.0V 800
CLK to Data Delay tCDD VCC = 5V (Notes 6, 7, 8) 200
ns
VCC = 2.0V 1000
CLK Low Time tCL VCC = 5V (Note 6) 250 ns
VCC = 2.0V 1000
CLK High Time tCH VCC = 5V (Note 6) 250 ns
VCC = 2.0V 0.5
CLK Frequency tCLK VCC = 5V (Note 6) DC 2.0
MHz
VCC = 2.0V 2000
CLK Rise and Fall tR, tF VCC = 5V 500
ns
VCC = 2.0V 4
CE to CLK Setup tCC VCC = 5V (Note 6) 1 μs
VCC = 2.0V 240
CLK to CE Hold tCCH VCC = 5V (Note 6) 60 ns
VCC = 2.0V 4
CE Inactive Time tCWH VCC = 5V (Note 6) 1 μs
VCC = 2.0V 280
CE to I/O High Impedance tCDZ VCC = 5V (Note 6) 70
ns
VCC = 2.0V 280
SCLK to I/O High Impedance tCCZ VCC = 5V (Note 6) 70
ns
Note 1: Limits at -40°C are guaranteed by design and are not production tested.
Note 2: All voltages are referenced to ground.
Note 3: ICC1T and ICC2T are specified with I/O open, CE and SCLK set to a logic 0.
Note 4: ICC1A and ICC2A are specified with the I/O pin open, CE high, SCLK = 2MHz at VCC = 5V; SCLK = 500kHz, VCC = 2.0V.
Note 5: CE, SCLK, and I/O all have 40kΩ pulldown resistors to ground.
Note 6: Measured at VIH = 2.0V or VIL = 0.8V and 10ns maximum rise and fall time.
Note 7: Measured at VOH = 2.4V or VOL = 0.4V.
Note 8: Load capacitance = 50pF.
Note 9: ICC1S and ICC2S are specified with CE, I/O, and SCLK open.
Note 10: VCC = VCC2, when VCC2 > VCC1 + 0.2V; VCC = VCC1, when VCC1 > VCC2.
Note 11: VCC2 = 0V.
Note 12: VCC1 = 0V.
Note 13: Typical values are at +25°C.
DS1302 Trickle-Charge Timekeeping Chip
12 of 13
Figure 6. Timing Diagram: Read Data Transfer
CE
SCLK
I/O
t
DC
t
CDH
t
CC
t
CDZ
t
CDD
t
R
t
F
t
CL
t
CH
ADDRESS/COMMAND BYTE READ DATA BYTE
t
CCZ
Figure 7. Timing Diagram: Write Data Transfer
CE
SCLK
I/O t
DC
t
CDH
t
CC
t
R
t
F
t
CL
t
CCH
t
CWH
ADDRESS/COMMAND BYTE WRITE DATA BYTE
t
CH
CHIP INFORMATION
TRANSISTOR COUNT: 11,500
THERMAL INFORMA TION
PACKAGE THETA-JA
(°C/W) THETA-JC
(°C/W)
8 DIP 110 40
8 SO (150 mils) 170 40
PACKAGE INFORMATION
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
8 PDIP 21-0043
8 SO (208 mils) 21-0262
8 SO (150 mils) 21-0041
DS1302 Trickle-Charge Timekeeping Chip
13 of 13
Maxim/Dallas Semiconductor cannot assume responsibili ty for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.
REVISION HISTORY
REVISION
DATE DESCRIPTION PAGES
CHANGED
Removed the leaded parts and references to the 16-pin SO package. 1, 4, 12
In the Features section, changed the 31 x 8 RAM feature to indicate that it is
battery backed. 1
Updated Figure 1 and removed original Figure 2 (oscillator circuit). 3, 5
Added a new Table 2 for the trickle charger resistor and diode select. 7
Replaced the timing diagrams (Figures 6 and 7). 12
120208
Added Package Information table. 12