HR10A-7P-4S(73) - HIROSE ELECTRIC

2017.12y

High performance miniature circular connectors

HR10 Series

Features

A simple, yet highly reliable design for

compact, high density applications

Although small in size, the HR10 series are full

featured connectors with a well integrated design.

2. Extremely easy mating/unmating

operations

Easy to operable, the single-action push-pull lock

structure allows for quick and efficient locking and

unlocking.

Product Speciﬁ cations

Ratings

Shell size No. of contacts Rated current

10 10

12 2A

13 20 2A

Ratings

Shell size No. of contacts Rated voltage

AC150V, DC200V

AC100V, DC140V

10 10

12 AC100V, DC140V

13 20 AC100V, DC140V

Ratings Operation temperature range -25 to +85ç

Storage temperature range -10 to +60ç

Items Specifications Conditions

1. Contact resistance 10mø min. Measured at DC 1A

2. Insulation resistance 1,000Mø min. Measured at DC 100V

3. Withstanding voltage No flashover or dielectric breakdown. AC 300V for one minute, 4 contacts : AC 500V for 1 minute

4. Vibration resistance No electrical discontinuity of 10µs or greater 10 to 55Hz/cycle, amplitude : 0.75mm, 3 axis directions,

for 2 hours each

5. Shock resistance No electrical discontinuity of 10µs or greater Acceleration : 490m/s2, duration : 11ms 3 directions,

3 times each

6. Mating Cycles Contact resistance : 15mø min. 1,000 times

7. Temperature cycle Insulation resistance : 1,000Mø min.

-55ç : 30minutes➝Normal temperature : 10 to 15 minutes➝

85ç : 30minutes➝Normal temperature :

10 to 15minutes, left for 5 cycles.

8. Humidity resistance 5Mø min. (at high humidity)

50Mø min. (at dry)

Temperature : 40ç, relative humidity : 90 to 95%,

left for 96 hours

In cases where the application will demand a high level of reliability, such as automotive,

please contact a company representative for further information.

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Materials / Finish

Items Material Finish Remarks

Exterior Zinc alloy, brass Matte finished nickel plating ----------------

Insulator Polyamide resin, PBT resin ---------------- Blue, Black

Contact Copper alloy HR10 : Gold plating

HR10A : Silver plating ----------------

qModel name : Indicates the HR10A Series. The part type is identified as follows.

HR10A : Lower cost type

HR10G : Shield type

HR10B : Coaxial contact type

wShell size : The shell size is the outer shell diameter or the mating interface end of the plug.

eShell type

P : Plug

R : Receptacle

J : Jack

rNumber of contacts

tContact form

P : Male contact

S : Female contact

yContact termination method:

None : Solder termination

C : Crimp termination

uOther specifications : A two-digit character is added to indicate other specifications as needed.

Product Number Structure

Refer to the chart below when determining the product specifications from the product number.

Please select from the product numbers listed in this catalog when placing orders.

HR10A -7P-3PC (**)

qwertyu

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Diagrams of Connectors in Combination

Notes

1 : When using a plug with male terminal, be sure to use a receptacle or jack ﬁ tted with female terminal.

2 : Standard ﬁ nish of the terminal is gold plating for the HR10, and silver plating for the HR10A and HR10G.

Be sure to use male and female connectors of the same plating.

Male Pin side Female Pin side

(HR10 Type Plug)

(HR10 Type Jack)

(HR10B Type Receptacle)

(HR10A-[ ]T Type Receptacle)

(HR10A-[ ]T Type Jack)

(HR10A Type Jack)

(HR10 • HR10A

HR10G Type Receptacle)

(HR10A Type Plug)

(HR10B Type Plug)

(HR10A-[ ]T Type Plug)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

HR10 type

HR10 type connectors, use a gold plated contact as the standard plating specification. Silver plating is used on the contacts

for other series such as HR10A and HR10G. To avoid mixing gold and silver contacts, please be sure to confirm the plating

specification when using HR10 type connectors with HR10A or HR10G connectors.

Plug

ØD

A Max

ØC

ØB

Unit : mm

Part No. HRS No. No. of Contacts A ØB ØC ØD Weight

HR10-7P-4P(73) 110-0021-6 73

28.5 11 7 5.2 8g

HR10-7P-4S(73) 110-0022-9 73

HR10-7P-6P(73) 110-0023-1 73

HR10-7P-6S(73) 110-0024-4 73

HR10-10P-12P(73) 110-0025-7 73

32.5 14 9.5 7.2 15g

HR10-10P-12S(73) 110-0026-0 73

(Representative example)

HR10-7P-6S(73)

Receptacle

E(HEX)

5.76.3

ØC

ØB

Unit : mm

Part No. HRS No. No. of Contacts A ØB ØC D E Weight

HR10-7R-4S(73) 110-0031-0 73 4

14 11 8.85 M8×0.5 10 3.5g

HR10-7R-4P(73) 110-0032-2 73

HR10-7R-6S(73) 110-0033-5 73 6

HR10-7R-6P(73) 110-0034-8 73

HR10-10R-12S(73) 110-0035-0 73 12 16 14 11.9 M11×0.75 13 6g

HR10-10R-12P(73) 110-0036-3 73

Remarks : For mounting holes, see page 20.

(Representative example)

HR10-7R-6S(73)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Receptacle (PCB dip type)

D(HEX)

Dip post dia.

Ø0.55

F5.7

ØA

ØB

Unit : mm

Part No. HRS No.

No. of Contacts

ØA ØB C D E F G

Weight

HR10-7R-4SA(73) 110-0059-9 73 4

11 8.85 M8×0.5 10

6.3 0.5 15.5

3gHR10-7R-6SA(73) 110-0050-4 73 6

HR10-7R-6PA(73) 110-0061-0 73

HR10-10R-12SA(73) 110-0049-5 73 12 14 11.9 M11×0.75 13 5g

HR10-10R-12PA(73) 110-0055-8 73

Remarks : 1. For mounting holes, see page 20.

2. For dip post arrangement, see page 16.

(Representative example)

HR10-7R-6SA(73)

Jack

ØD

5.5

A Max

ØB

ØC

Unit : mm

Part No. HRS No. No. of Contacts A ØB ØC ØD Weight

HR10-7J-4S(73) 110-0027-2 73 4

28.5 11 8.85 5.2 7g

HR10-7J-4P(73) 110-0028-5 73

HR10-7J-6S(73) 110-0029-8 73 6

HR10-7J-6P(73) 110-0030-7 73

HR10-10J-12S(73) 110-0037-6 73 12 32.5 14 11.9 7.2 14g

HR10-10J-12P(73) 110-0038-9 73

(Representative example)

HR10-7J-6S(73)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Plug (Solder type)

ØB

ØC

ØD

Unit : mm

Part No. HRS No. No. of Contacts A ØB ØC ØD Weight

HR10A-7P-4P(73) 110-0301-2 73 4

35 11.5 7 5 9g

HR10A-7P-4S(73) 110-0302-5 73

HR10A-7P-5P(73) 110-0318-5 73 5

HR10A-7P-5S(73) 110-0319-8 73

HR10A-7P-6P(73) 110-0303-8 73 6

HR10A-7P-6S(73) 110-0304-0 73

HR10A-10P-10P(73) 110-0407-3 73 10

43 14.7 9.5

16g

HR10A-10P-10S(73) 110-0408-6 73

HR10A-10P-12P(73) 110-0401-7 73 12

HR10A-10P-12S(73) 110-0402-0 73

HR10A-13P-20P(73) 110-0713-0 73 20 59 19 13 37g

HR10A-13P-20S(73) 110-0716-8 73

(Representative example)

HR10A-7P-6P(73)

Plug(Crimp type)

ØC

ØB

ØD

Unit : mm

Part No. HRS No. No. of Contacts A ØB ØC ØD Weight

HR10A-7P-4PC(73) 110-0501-1 73 4

35 11.5 7 5 9g

HR10A-7P-4SC(73) 110-0502-4 73

HR10A-7P-6PC(73) 110-0503-7 73 6

HR10A-7P-6SC(73) 110-0504-0 73

HR10A-10P-10PC(73) 110-0601-6 73 10

43 14.7 9.5

16g

HR10A-10P-10SC(73) 110-0602-9 73

HR10A-10P-12PC(73) 110-0603-1 73 12

HR10A-10P-12SC(73) 110-0604-4 73

HR10A-13P-20PC(73) 110-0701-0 73 20 59 19 13 37g

HR10A-13P-20SC(73) 110-0702-3 73

(Representative example)

HR10A-7P-6PC(73)

HR10A•10G Types

HR10A connectors are a lower-cost version, yet still provide a high "Value Add" while preserving the superior characteristics

of the HR10 connectors. Cable clamps are crimped using a special crimping tool, and the shells have a rubber boot which

provides a flexible design that helps to prevent cable twisting.

The HR10G connector is a shielded type connector which has an internal contacting structure between the plug shell and

receptacle shell.

Contacts in both HR10A and 10G connectors are silver plated as standard.

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Unit : mm

Part No. HRS No.

No. of Contacts

ØA ØB C D E F

Weight

Remarks

HR10A-7R-4SC(73) 110-0506-5 73 4

11 8.85 M8×0.5 10

6.3

HR10A-7R-4PC(73) 110-0505-2 73 12.2

HR10A-7R-6SC(73) 110-0508-0 73 612

HR10A-7R-6PC(73) 110-0507-8 73 12.2

HR10A-10R-10SC(71) 110-0606-0 71 10

14 11.9 M11×0.75 13

HR10A-10R-10PC(71) 110-0605-7 71 12.2

HR10A-10R-12SC(71) 110-0608-5 71 12 12

HR10A-10R-12PC(71) 110-0607-2 71 12.2

HR10A-13R-20SC(73) 110-0703-6 73 20 18 15.4 M14×0.75 17 9.3 15 8g

HR10A-13R-20PC(73) 110-0704-9 73

HR10G-7R-4SC(73) 110-1701-6 73 4

11 8.85 M8×0.5 10

6.3

Shield type

HR10G-7R-4PC(73) 110-1702-9 73 12.2

HR10G-7R-6SC(73) 110-1705-7 73 612

HR10G-7R-6PC(73) 110-1706-0 73 12.2

HR10G-10R-10SC(71) 110-1707-2 71 10

14 11.9 M11×0.75 13

HR10G-10R-10PC(71) 110-1708-5 71 12.2

HR10G-10R-12SC(71) 110-1709-8 71 12 12

HR10G-10R-12PC(71) 110-1710-7 71 12.2

HR10G-13R-20SC(73) 110-1711-0 73 20 18 15.4 M14×0.75 17 9.3 15 8g

HR10G-13R-20PC(73) 110-1712-2 73

Remarks : For mounting holes, see page 20.

Receptacle (Solder type)

E(HEX)

ØB

ØC

5.7F

(Representative example)

Unit : mm

Part No. HRS No.

No. of Contacts

AØBØC D EE

Weight

Remarks

HR10A-7R-4S(73) 110-0305-3 73 4

14 11 8.85 M8×0.5 10

6.3

HR10A-7R-4P(73) 110-0306-6 73

HR10A-7R-5S(73) 110-0320-7 73 5

HR10A-7R-5P(73) 110-0321-0 73

HR10A-7R-6S(73) 110-0307-9 73 6

HR10A-7R-6P(73) 110-0308-1 73

HR10A-10R-10S(71) 110-0409-9 71 10

16 14 11.9 M11×0.75 13 5g

HR10A-10R-10P(73) 110-0410-8 73

HR10A-10R-12S(71) 110-0403-2 71 12

HR10A-10R-12P(73) 110-0404-5 73

HR10A-13R-20S(73) 110-0714-2 73 20 19.2 18 15.4 M14×0.75 17 9.3 8g

HR10A-13R-20P(73) 110-0715-5 73 20.2

HR10G-7R-4S(73) 110-1601-1 73 4

14 11 8.85 M8×0.5 10

6.3

Shield type

HR10G-7R-4P(73) 110-1602-4 73

HR10G-7R-6S(73) 110-1605-2 73 6

HR10G-7R-6P(73) 110-1606-5 73

HR10G-10R-10S(71) 110-1607-8 71 10

16 14 11.9 M11×0.75 13 5g

HR10G-10R-10P(73) 110-1608-0 73

HR10G-10R-12S(71) 110-1609-3 71 12

HR10G-10R-12P(73) 110-1610-2 73

Remarks : For mounting holes, see page 20.

HR10A-7R-6S(73)

Receptacle (Crimp type)

D(HEX)

ØB

ØA

(Representative example)

HR10A-10R-12SC(71)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Dust cap

ØA

0.2

ØD

ØC

ØE

HR10-7R-C

Receptacle (Dip type)

D(HEX)

Dip post dia.

0.2∞0.5

ØA

ØB

F5.7E

Unit : mm

Part No. HRS No.

No. of

Contacts

ØA ØB C D E F G

Weight Remarks

HR10A-7R-4SB(73)

110-0314-4 73 4

11 8.85 M8×0.5 10

6.3 0.5 15.6

HR10A-7R-4PB(73)

110-0315-7 73

HR10A-7R-5SB(73)

110-0322-2 73 5

HR10A-7R-6SB(73)

110-0316-0 73 6

HR10A-7R-6PB(73)

110-0317-2 73

HR10A-10R-10SB(71)

110-0413-6 71 10

14 11.9 M11×0.75 13

HR10A-10R-10PB(71)

110-0414-9 71

HR10A-10R-12SB(71)

110-0415-1 71 12

HR10A-10R-12PB(71)

110-0416-4 71

HR10A-13R-20SB(73)

110-0707-7 73 20 18 15.4 M14×0.75 17 9.3 0 17.8 8g

HR10A-13R-20PB(73)

110-0708-0 73

HR10G-7R-4SB(73)

110-1801-0 73 4

11 8.85 M8×0.5 10

6.3 0.5 15.6

Shield

type

HR10G-7R-4PB(73)

110-1802-3 73

HR10G-7R-6SB(73)

110-1805-1 73 6

HR10G-7R-6PB(73)

110-1806-4 73

HR10G-10R-10SB(71)

110-1807-7 71 10

14 11.9 M11×0.75 13 5g

HR10G-10R-10PB(71)

110-1808-0 71

HR10G-10R-12SB(71)

110-1809-2 71 12

HR10G-10R-12PB(71)

110-1810-1 71

HR10G-13R-20SB(73)

110-1811-4 73 20 18 15.4 M14×0.75 17 9.3 0 17.8 8g

HR10G-13R-20PB(73)

110-1812-7 73

Remarks : 1. For mounting holes, see page 20.

2. For dip post arrangement, see page 16.

Unit : mm

Part No. HRS No. ØA B ØC ØD ØE

HR10-7R-C 110-0058-6 00 11 7 8 11.2 13

HR10-10R-C 110-0052-0 00 14 8.5 10.8 14.1 15

HR10A-13R-C 110-0452-8 00 17.5 11.5 14 18.1 19

(Representative example)

HR10A-7R-6SB(73)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Jack (Solder type)

ØC

ØB

5.5

ØD

(Representative example)

Unit : mm

Part No. HRS No.

No. of Contacts

A ØB ØC ØD Weight

HR10A-7J-4S(73) 110-0309-4 73 4

35.3 11 8.85 5 9g

HR10A-7J-4P(73) 110-0310-3 73

HR10A-7J-6S(73) 110-0311-6 73 6

HR10A-7J-6P(73) 110-0312-9 73

HR10A-10J-10S(73) 110-0411-0 73 10

43.5 14 11.9 7 16g

HR10A-10J-10P(73) 110-0412-3 73

HR10A-10J-12S(73) 110-0405-8 73 12

HR10A-10J-12P(73) 110-0406-0 73

HR10A-7J-6S(73)

Jack (Crimp type)

ØC

ØB

ØE

Unit : mm

Part No. HRS No.

No. of Contacts

A ØB ØC D ØE Weight

HR10A-7J-4SC(73) 110-0510-2 73 4 35.3 11 8.85

5.5

59g

HR10A-7J-6SC(73) 110-0512-8 73 6

HR10A-10J-10SC(73) 110-0610-7 73 10 43.5 14 11.9

16g

HR10A-10J-12SC(73) 110-0612-2 73 12

HR10A-13J-20SC(73) 110-0705-1 73 20 58.5 18 15.4 8.5 37g

HR10A-13J-20PC(73) 110-0706-4 73

(Representative example)

HR10A-7J-6SC(73)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Plug

HR10B Type Connector

The HR10B connector combines 10 signal lines and one coaxial contact in the standard number 10 shell. Performance

specifications for the coaxial contacts are on the 11 page.

Ø14.7

ØB

Unit : mm

Part No. HRS No. A ØB Applicable coaxial contact

HR10B-10P-10PC(73) 110-0901-0 73 50 5 HR10B-2.5CJ(73)

HR10B-10PA-10PC(73) 110-0906-3 73 43 7

(Representative example)

HR10B-10P-10PC(73)

Receptacle

13(HEX)

M11∞0.75

Ø11.9

Ø14

6.3

Unit : mm

Part No. HRS No. Applicable coaxial contact

HR10B-10R-10SC(71) 110-0902-2 71 HR10B-2.5CP(73)

Remarks : For mounting holes, see page 20.

(Representative example)

HR10B-10R-10SC(71)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Plug

(clamp)

4.1

5.2 3.6

Ø3.8

7.1

18.05

Ø4.2

Ø1.1

(Representative example)

Unit : mm

Part No. HRS No. Applicable cable Applicable connector

HR10B-2.5CP(73) 110-0904-8 73 0.8D-QEW-CW(By Fjikura wire) HR10B-10R-10SC(71)

HR10B-2.5CP(73)

Jack

(clamp)

Ø2.65

7.25

18.2

Ø4.2

Ø1.1

4.1

5.2 3.6

(Representative example)

Unit : mm

Part No. HRS No. Applicable cable Applicable connector

HR10B-2.5CJ(73) 110-0903-5 73 0.8D-QEW-CW(By Fjikura wire) HR10B-10P-10PC(73)

HR10B-2.5CJ(73)

Coaxial contacts

The coaxial contacts shown here are for use with the HR10B connector.These contacts have locking barbs and are inserted

from the rear of connector.Please use the following information to select the correct terminals.

Materials / Finish Performance

Part Material Finish

Plug shell Brass Gold plating

Jack shell

Insulator Tetraﬂ uoride resin

Male pin Phosphor bronze Gold plating

Female pin Beryllium copper

Description Test data

Impedance

50ø

Insulation resistance 1000Mø or more at DC250V

Contact resistance

Center 6.5mø or less and outer 4mø or less at DC1A

Withstanding voltage AC250V r.m.s for 1minute

V.S.W.R

1.3 or less for 0 to 1000MHz

Pull force

4.9N (500gf) or more

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Cable connecting methods

11±0.5

1.4±0.2

3.7±0.2

(2.5)

Slit cable outer jaket

2 pieces (180° reverse side)

1. Dimensions for cable end treatment are shown in Fig 1.

2. Termination is described below.

(1) Strip cable outer jacket as indicated.

(2) Slit outer jacket on both sides per Fig.1.

(3) Fold back outer cover.

(4) Remove insulator from cable.

1. Cable end treatment

Fig.1

Male pin

Soldering

Should fix flush

Contact fixing jig such as vise

1. Solder male pin to cable center conductor as indicated in Fig.2.

(1) Pre-solder the solder pot of pin with Ø0.5mm string solder.

(2) Male pin should fit flush against the cable insulator as

shown.

(3) Remove any excess solder from the pin with a knife.This

surface must be smooth.

(4) A properly soldered terminal will yield 500gf when stretched.

2. Soldering male pin to cable center conductor

Fig.2

Clamp

15±0.2

Connector

Remove excess insulator material

(remaining after clamping is complated)

with a knife or aimilarobject.

1. Insert the cable into the connector and make sure to push it

all the way in. To confirm that the cable is fully inserted,

make sure that the depth is 1.5 ± 0.2mm by measuring from

the end of the connector to the tip of the male contact by

using a vernier calipers or other suitable measuring device.

2. Use the HR10-TC-01 tool to crimp the metal fitting to the

cable.

3. Crimping cable outer conductor

Fig.3

HR10B-2.5CP(73)

HR10B-2.5CJ(73)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

HR10A-( )T Type (Threaded Coupling Type)

HR10A-( )T connector is a new product having a threaded coupling locking mechanism. Electric parformance is same as

HR10 and HR10A push-pull locking type connectors.

Plug (Crimp type)

Ø7

Ø17

Ø9.5

M13∞0.75

Unit : mm

Part No. HRS No.

No. of Contacts

HR10A-10TP-12PC(73) 110-0455-6 73 12

HR10A-10TP-12PC(73) (Representative example)

(Representative example)

Plug (Solder type)

ØC

ØA

ØE

HR10A-10TP-12P(73)

Unit : mm

Part No. HRS No.

No. of Contacts

ØA B ØC D ØE Remarks

HR10A-7TP-6P(73) 110-0331-3 73 6 12 M10×0.75 7 35 5

HR10A-7TP-6P(74) 110-0331-3 74 Gold plating

HR10A-10TP-12P(73) 110-0432-0 73

17 M13×0.75

9.5

43 7

HR10A-10TPA-12S(73) 110-0446-5 73

HR10A-10WTP-12P(73) 110-1101-9 73 15 M12×0.75 45.8 6.5 *

HR10A-10WTP-12S(73) 110-1106-2 73

HR10A-13TPD-20P(73) 110-1015-9 73 20 20 M17×1 13 56.5 7

*Waterproof plug need resin ﬁ lling inside when connector assembly.

When mated, the connector against water penetration.

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Unit : mm

Part No. HRS No.

No. of Contacts

ØA B C DEFG H

HR10A-7TR-6SA(73) 110-0330-0 73 6 11 M10×0.75

M8×0.5

6.3 0.5

15.5 Ø0.55

HR10A-10TR-12SB(73) 110-0433-3 73

12 14 M13×0.75

M11×0.75

15.6

0.2×0.5

HR10A-10TR-12PB(73) 110-0457-1 73 15.5

HR10A-10TR-12PE(73) 110-0445-2 73 14

HR10A-10WTR-12SB(73) 110-1102-1 73 M12×0.75

M10.5×0.75

6.8 015.6

HR10A-13TR-20SB(73) 110-1014-6 73 20 18 M17×1

M14×0.75

17 9.3 17.8

Remarks : 1.For mounting holes, see page 15. However, 7TR size shell be referred to page 20 on the shell size 7.

2.For dip post arrangement, see page 16.

Receptacle (Solder type)

F(HEX)

ØD

B5.7

Unit : mm

Part No. HRS No.

No. of Contacts

A B C ØD E F Remarks

HR10-7TR-6S(73) 110-0089-0 73 6 M10×0.75 6.3 M8×0.5 11 14 10 Gold plating

HR10A-10TR-12S(73) 110-0453-0 73 12 M13×0.75 M11×0.75 14 16 13

HR10A-10WTR-12S(73) 110-1104-7 73 M12×0.75 6.8 M10.5×0.75

Remarks : For mounting hole, see page 15(10TR,10WTR) 20(7TR).

HR10A-10TR-12S(73) (Representative example)

Receptacle (Crimp type)

F(HEX)

ØA

Unit : mm

Part No. HRS No.

No. of Contacts

ØA B C D E F

HR10A-10TR-12SC(73) 110-0456-9 73 12 14 12 6.3 M13×0.75 M11×0.75 13

HR10A-13TR-20SC(73) 110-1002-7 73 20 18 15 9.3 M17×1 M14×0.75 17

Remarks : For mounting hole, see page 15

HR10A-10TR-12SC(73) (Representative example)

Receptacle (Dip type)

D(HEX)

Dip post

ØA

E5.7 F

HR10A-10TR-12PB(73) (Representative example)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Jack (Solder type)

Unit : mm

Part No. HRS No.

No. of Contacts

ØA B ØC D Remarks

HR10A-10TJ-12S(73) 110-0436-1 73

12 14.7 41.3 7 M13×0.75

HR10A-10TJ-12P(73) 110-0459-7 73

HR10A-10WTJ-12S(73) 110-1103-4 73 14 46.5 6.5 M12×0.75 *

*Waterproof jack need resin ﬁ lling inside when connector assembly.

When mated, the connector against water penetration.

ØA

ØC

(Representative example)

HR10A-10TJ-12S(73)

Panel mounting hole dimensions (Screw coupling)

The mounting hole dimensions shown below are for connectors to be tightened by a hexagonal nut from the back of the

panel. The dimensions below apply only to the HR10A-( )T and not the 7TR. For the dimensions of connectors of other

types, see page 20.

9.6 +0.1

Ø11.1

+0.1

Ø10.6+0.1

Ø14.1

+0.1

Type HR10A-10TR

(Panel thickness 1 to 2mm)

Type HR10A-10TR

(Panel thickness 1 to 2mm)

9.6 +0.1

Type HR10A-10WTR

(Panel thickness 1 to 2mm)

8.6 +0.1

1.6 +0.1

Type HR10A-13TR

(Panel thickness 1 to 1.5mm)

HR10 Series●High performance miniature circular connectors

Mar.1.2019Copyright2019HIROSEELECTRICCO.,LTD.AllRightsReserved.

Male contact

Female contact

1.15

1.2

1.15

1.2

Receptacle dip post arrangement dimensions

Contact

Unit : mm

Type Part No. HRS No. Type of plating Applicable

cable

Loose

contact

HR10-PC-111 110-0515 6

Partial gold plating

26 to 30

AWG

HR10-PC-112 110-0513 0

Silver plating

Reel

contact

HR10-PC-211 110-0516 9

Partial gold plating

HR10-PC-212 110-0514 3

Silver plating

Remarks : 1. Use cables with a coating outside diameter of 1mm or less.

2. Loose piece terminal are available in packs. Each pack

contains 100 terminals. Strip terminals are available in

reels. Each reel contains 10,000 terminals.

Unit : mm

Type Part No. HRS No. Type of plating Applicable

cable

Loose

contact

HR12-SC-111 112-0410 0

Partial gold plating

26 to 30

AWG

HR12-SC-112 112-0411 3

Silver plating

Reel

contact

HR12-SC-211 112-0407 6

Partial gold plating

HR12-SC-212 112-0408 9

Silver plating

Remarks : 1. Use cables with a coating outside diameter of 1mm or less.

2. Loose piece terminal are available in packs. Each pack

contains 100 terminals. Strip terminals are available in

reels. Each reel contains 10,000 terminals.

Remarks : 1. The above ﬁ gures are views from the mating side and pin inserts from the wiring-connection side.

2. Dimensional tolerance of ±0.05 is recommended for the board arrangement.

1.131.13

1.561.56

1.13

7-size 4 cores 7-size 6 cores

10-size 10 cores 10-size 12 cores

13-size 20 cores

1.13 0.9 0.9

1.8 1.8

(4 Places)

(6 Places)

(10 Places)

(12 Places)

(20 Places)

1.8 1.8

7-size 5 cores

(5 Places)

2.5

2.58

2.38 2.38

0.950.95

2.75

2.11

0.55

0.48

2.85 2.85

0.95 0.95

1.1

1.38

2.5

2.55 2.55

1 1 1.77 1.77 0.8

2.4

0.8

2.4

2.71 2.71

910

5678910

161514131211

17 18 19 20

712 11

Ø0.8＋0.1

HR10 Series●High performance miniature circular connectors

Tools

Type Item Part No. HRS No. Applicable terminal Applicable cable

Manual Manual crimping tool HT802/HR12-SC-1 150-0400-3 HR10-PC-112 26 to 30AWG

HR12-SC-112

Automatic

Automatic crimping

machine body CM-105C 901-0001-0 _______ _______

Applicator AP105-HR12-1 901-2015-9

HR10-PC-211

212

26 to 30AWG

HR12-SC-211

212

Cable crimping tool HR10-TC-01 150-0036-2 _______

(HR10B-2.5CP(73),

HR10B-2.5CJ(73))

HR10A-TC-02 150-0041-2 Ø5, Ø7

Extractor

HR12-SC-TP 150-0050-3 HR12-SC-112

_______

HR12-SC-212

RP6-SC-TP 150-0039-0 HR10-PC-112

HR10-PC-212

HR10B-TP 150-0061-0 HR10B-2.5CP(73)

HR10B-2.5CJ(73)

(HT802/HR12-SC-1)

Hand Crimp Tool

(HR10A-TC-02)

Hand Cable Crimp Tool

(HR10B-TP)

Coaxial Contact Removal Tool

(HR12-SC-TP)

Auto Crimp Tool CM-105C

(RP6-SC-TP)

Extraction Tool

HR10 Series●High performance miniature circular connectors

How to use a connector

HR10-10P-T02 HR10-10J-T04

Part No. HRS No. Applicable connector

HR10-7P-T01 150-0009-0 HR10-7P

HR10-10P-T02 150-0010-9 HR10-10P

HR10-7J-T03 150-0011-1 HR10-7J

HR10-10J-T04 150-0012-4 HR10-10J

HR10-13P-T05 150-0059-8 HR10-13P

HR10-13J-T06 150-0060-7 HR10-13J

Panel

Plug Cable

Receptacle

Panel

Plug Cable

Receptacle

Panel

Plug connection sleeve Cable

Panel

Plug connection sleeve

Cable

Connecting tools

When terminating the wires, use the jigs noted below for easy assembly / disassembly of the connector parts.

1.Inserting 2.Withdrawing

HR10 TYPEHR10A TYPE

Hold the plug at point A, align the plug guide with the

receptacle guide, and push the plug straight.

The plug will mate with the receptacle smoothly.

Hold the plug connection sleeve B and pull the sleeve

straight. The plug will come off easily.

HR10 Series●High performance miniature circular connectors

HR10 TYPEHR10A TYPE

Cable assembly procedure on plug side

This applies also to the jack side assembly procedure.

No special procedure is given here for the receptacle side because no special procedure is necessary.

Table 2 spanner jaw distance

Size HR10 HR10A

7 8 7.5

10 11 9.5

1 3 ____ 1 3

Table 1

Size Tightening force

7 1.5N·m(15kg·cm)

10 2N·m(20kg·cm)

Table 3 cable end processing dimensions

Size

Dimension C

for HR10

Dimension D for HR10A

Solder type Crimp type

7 5.5 or less 10 15 to 20

10 7 or less 16

1 3 ____ 2 5

HR10 TYPE HR10A TYPE

1 Use cables with a nominal sectional area of 0.129mm2 (26 AWG) at the ﬁ nish outside diameters applicable for each size.

After processing the cable ends according to the dimensions in the above drawings, ﬁ t the parts to the cable as shown

in the drawings.

Fit the parts to the cable in the following order:

tightener, clamp washer, and plug body.

Fit the parts to the cable in the following order:

cord bushing and plug body.

(solder type)

Insert the P shell unit into the assembly tool stand and solder it.

(crimp type)

After crimping the appropriate crimp terminal to the cable core, insert the crimp terminal into the terminal hole in the P

shell unit.

Assemble the connector in the following steps.

1. Screw the plug body into the thread in the P shell unit

with the tightening force shown in Table 1 using a

torque wrench with a ﬁ xed torque.

Before tightening the plug body,slacken part C so that

no load is applied to the soldered wires.

2. Apply the clamp washer to the bifurcated part of the

plug body, and then tighten the tightener until surface

B touches the plug body surface A.

Note : In order to prevent looseing, please apply an

adhesive at the thread of plug body.

1. Fix by caulking the clamp accompanying the cable

with the cable crimping tool(HR10A-TC-02)

2. Screw the plug body into the thread in the P shell until

with a tightening force shown in Table 1 using a torque

wrench with a ﬁ xed torque. Before tightening the plug

body, slacken the part D so that no load is applied to

the soldered wires.

3. Tighten the set screw so that the tip of the screw

presses one of the two bosses on the clamp.

Fix the set screw with a tightening torque of 0.3N

(3kg·cm).

4. Attach the cord bushing to the plug body.

Note : In order to prevent looseing, please apply an

adhesive at the thread of plug body.

5 This completes the work.

For any question on using the plugs, contact our sales or engineering department.

P shell unit

Set screw

Boss

Clamp Plug body

Spanner jaw distance

Cord bushing

Cable

Ｄ

Ａ

2 or more

About 2 for solder type

2 for crimp type

-0.5

P shell unit Plug body

Bifurcated part

Clamp washer Tightener Cable

Face BFace A

Spanner jaw distance

About 2 C

HR10 Series●High performance miniature circular connectors

Recommended Mounting Hole

Mounting hole dimension shown here is tight by hexagon nut from back side.

Contact Arrangement

ØC

7 size 10 size 13 size

A 1.6 2.6

B 5.1 6.6 8.6

C 8.1 11.1 14.1

Panel thickness 0.7 to 2 0.8 to 1.5

Shell size

Map mark

+0.1

0+0.1

+0.1

0+0.1

+0.1

0+0.1

Shell size 7 size 10 size

Contact arrangement

No. of contacts 4 5 6 10 12

Withstanding voltage AC500V for a minute AC300V for a minute

Current rating 2A

Insulation resistance MIN 1,000Mø

Contact resistance MAX 10mø

Solder pot inside dia. Ø0.8

Shell size 10 size 13 size

Contact arrangement

No. of contacts 10+coaxial contact 20

Withstanding voltage AC300V for a minute

Current rating 2A

Insulation resistance MIN 1,000Mø

Contact resistance MAX 30mø MAX 10mø

Solder pot inside dia. ____ Ø0.8

Notes 1. The contact arrangement shown here is the mating surface of socket insert assembled.

2. The withstanding voltage shown here is test voltage value.

3. The isulation resistance value is measured at DC100V.

4. The contact resistance value is measured at DC1A.

HR10 Series●High performance miniature circular connectors

2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN

TEL: +81-45-620-3526 Fax: +81-45-591-3726

http://www.hirose.com

http://www.hirose-connectors.com

The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.

The contents of this catalog are current as of date of 12/2017. Contents are subject to change without notice for the purpose of improvements.

Precautions

1. Switch off the power of the circuit before disconnecting or plugging-in the connector.

2. Use a connector with socket contacts at the power side of the circuit.

3. Make sure that the coupling is in completely locked position.

4. Cable clamping, cable rotation, and other forces may vary with the cable construction. Please make sure that your cable is

suitable for use with these connectors before usage and production.

5. This product series uses silver plated contacts. Silver reacts easily to exposure to sulfur gas so the below conditions may

cause tarnishing.

・Dusty environments

・Area with a high concentration area of gases such as sulfur dioxide gas, hydrogen sulfide gas, nitrogen dioxide gas

and so on.

Example; In close proximity to factory exhaust, automotive emissions, etc.

・Close to heaters, or in other areas marked by extreme temperature differences or high humidity.

・Close to rubber products includes rubber adhesives.

The Electrical connection is not affected by tarnishing on a silver surface due to the wiping effect of the contact pins.

Storage

Packing state; Packed in original packing or equivalent container

Temperature -10 to +60

Humidity 85% Max

(It is recommended that the product be stored in an area of normal level of temperature and humidity, and free of any

temperature fluctuation)

Please use this products within 6 months of delivery.

(After 6 month, please check the solderbility before use)

“Storage” means long-term storage of the unused products in sealed packaging, prior to assembly to PCB.

HR10 Series●High performance miniature circular connectors