1290Q16-U - THAT - Datasheet.Directory

FEATURES

• Good CMRR: typ. 50 dB at 60Hz

• Low cost, self-contained, dual

• Excellent audio performance

– Wide bandwidth: typ. >7.6 MHz

– High slew rate: typ. 14 V/μs

– Low distortion: typ. 0.0006% THD

– Low noise: typ. -104 dBu

• Low current: typ. 3 mA (per amplifier)

• Several gains: 0 dB, ±3 dB, ±6 dB

APPLICATIONS

• Balanced Audio Line Receivers

• Instrumentation Amplifiers

• Differential Amplifiers

• Precision Summers

• Current Shunt Monitors

THAT 1290, 1293, 1296

The THAT 1290 series of precision differen-

tial amplifiers was designed primarily for use as

balanced line receivers for audio applications.

Gains of 0 dB, ±3 dB, and ±6 dB are available to

suit various applications requirements.

These devices include on-board precision

thin-film resistors which offer good matching and

excellent tracking due to their monolithic

construction. Manufactured in THAT Corpora-

tion’s proprietary complementary dielectric isola-

tion (DI) process, the 1290 series provides the

sonic benefits of discrete designs with the

simplicity, reliability, matching, and small size of

a fully integrated solution.

All three versions of the part typically exhibit

50 dB of common-mode rejection. With 14 V/μs

slew rate, 7.6 MHz or higher bandwidth, and

0.0006% THD, these devices are sonically trans-

parent. Moreover, current consumption is

typically a low 6 mA (3 mA per amplifier).

The 1290 series is available in a 16-pin

QSOP package.

Description

Sns BSns

Out B

Out

Ref BRef

16 15 14 13 12 11 10

1234567

VEE

In+ A In+ B

In- A In- B NC

NCNC

Gain

Part No.

THAT1290

THAT1293

THAT1296

0 dB

-3 dB

-6 dB

R1 & R3R2 & R4

Figure 1. Equivalent circuit

16REF A 15OUT A 14SENSE A 13VCC

12SENSE B 11OUT B 10REF B 9N/C 8N/C 7N/C 6IN- B 5IN+ B 4VEE

3IN+ A 2IN- A 1N/C

Pin NumberPin Name

Table 1. Pin assignments

Low Cost Dual Balanced

Line Receiver ICs

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; US

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

Document 600121 Rev 01 Page 2 of 10 THAT 1290 Series

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

Supply Voltages (VCC - VEE)40V

Maximum In- or In+ Voltage -50V + VCC , +50V + VEE

Max/Min Ref or Sense Voltage VCC +0.5V, VEE -0.5V

Maximum Output Voltage (VOM)V

CC +0.5V, VEE -0.5V

Storage Temperature Range (TST) -40 to +125 ºC

Operating Temperature Range (TOP) -40 to +85 ºC

Output Short-Circuit Duration (tSH) Continuous

Junction Temperature (TJ) +125 ºC

Absolute Maximum Ratings2,3

SPECIFICATIONS1

Parameter Symbol Conditions Min Typ Max Units

Supply Current ICC; -IEE No signal — 6 8 mA

Supply Voltage VCC-VEE 6 — 36 V

Input Voltage Range VIN-DIFF Differential (equal and opposite swing)

1290 (0dB gain) — 21.5 — dBu

1293 (-3dB gain) — 24.5 — dBu

1296 (-6dB gain) — 27.5 — dBu

VIN-CM Common Mode

1290 (0dB gain) — 27.5 — dBu

1293 (-3dB gain) — 29.1 — dBu

1296 (-6dB gain) — 31 — dBu

Input Impedance5ZIN-DIFF Differential

1290 (0dB gain) — 18 — kΩ

1293 (-3dB gain) — 21 — kΩ

1296 (-6dB gain) — 24 — kΩ

ZIN-CM Common Mode

All versions — 18 — kΩ

Common Mode Rejection Ratio CMRR Matched source impedances

DC, VCM = ±10V 40 50 — dB

60Hz 40 50 — dB

20kHz — 50 — dB

Power Supply Rejection Ratio6PSRR ±3V to ±18V; VCC = -VEE; all gains — 90 — dB

Total Harmonic Distortion THD Vout = 5Vrms, f = 1kHz, BW = 22kHz, RL = 2 kΩ

— 0.0006 — %

Output Noise eOUT 22 Hz to 22kHz bandwidth

1290 (0dB gain) — -104 — dBu

1293 (-3dB gain) — -105.5 — dBu

1296 (-6dB gain) — -107 — dBu

Slew Rate SR RL = 2kΩ; CL = 200 pF, all gains — 14 — V/μs

Electrical Characteristics2,4

1. All specifications are subject to change without notice.

2. Unless otherwise noted, TA=25ºC, VCC=+15V, VEE= -15V.

3. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only; the functional operation of

the device at these or any other conditions above those indicated in the operational sections of this specification is not impli ed. Exposure to absolute maximum rating condi-

tions for extended periods may affect device reliability.

4. 0 dBu = 0.775 Vrms.

5. Absolute resistance values can vary ±30% from the typical values shown. Input impedance is monitored by lot sampling.

6. Defined with respect to differential gain.

7. Parameter guaranteed over the entire range of power supply and temperature.

THAT 1290 Series Page 3 of 10 Documen

600121 Rev 01

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

Parameter Symbol Conditions Min Typ Max Units

Small signal bandwidth BW-3dB RL = 2kΩ; CL = 10 pF

1290 (0dB gain) — 7.6 — MHz

1293 (-3dB gain) — 9.6 — MHz

1296 (-6dB gain) — 11.6 — MHz

Output Gain Error GER-OUT -0.2 0 0.2 dB

Output Voltage Swing VO+ RL = 2kΩ; CL = 200 pF VCC-3 VCC-2 — V

VO- RL = 2kΩ; CL = 200 pF — VEE+2 VEE+3 V

Output Offset Voltage VOFF No signal -10 — 10 mV

Output Short Circuit Current ISC RL = 0 Ω— ±42 — mA

Capacitive Load7CL——200 pF

Channel Separation f = 1kHz — 120 — dB

Electrical Characteristics (con’t)2,4

Sns

Out

Ref

VCC

VEE

VIN(CM)

VIN(DIFF)

In+

In-

In+

In- RL

In+

In-

Differential Input

Common-mode Input

Figure 2. Simplified test circuit (1/2 of 129x shown)

The THAT 1290 series ICs consist of two high

performance opamps with integrated, thin-film resis-

tors. These designs take advantage of THAT’s fully

complementary dielectric isolation (DI) process to

deliver excellent performance with low current

consumption. The devices are simple to apply in a

wide range of applications.

Resistor Matching, Values, and CMRR

The 1290-series devices rely upon the inherent

matching of silicon-chromium (Si-Cr), thin-film,

integrated resistors to achieve a 50 dB common

mode rejection ratio and tight gain accuracy. No

trimming is performed. As a result of their

monolithic construction, the R3/R4 ratio matches

within ±0.5% of the R1/R2 ratio. 0.5% matching is

about 50 dB CMRR for the 1296 and 52 dB for the

1290.

However, while the resistor ratios are tightly

controlled, the actual value of any individual resistor

is not. Lot-to-lot variations of up to ±30% are to be

expected.

If higher CMRR is required in a simple dual

input stage, consider the THAT 1280-series ICs.

These parts are laser-trimmed to improve the inher-

ent precision of our thin-film resistor process. For

demanding applications in which the source imped-

ance balance may be less than perfect, the 1200-

series ICs offer exceptional CMRR performance via a

patented method of increasing common-mode input

impedance.

Input Considerations

The 1290-series devices are internally protected

against input overload via an unusual arrangement of

diodes connecting the + and - input pins to the

power supply pins. The circuit of Figure 3 shows the

arrangement used for the R3/R4 side; a similar one

applies to the other side. The zener diodes prevent

the protection network from conducting until an

input pin is raised at least 50 V above VCC or lowered

50 V below VEE. Thus, the protection networks

protect the devices without constraining the allow-

able signal swing at the input pins. The reference

(and sense) pins are protected via more conventional

reverse-biased diodes which will conduct if these

pins are raised above VCC or below VEE.

To reduce risk of damage from ESD, and to

prevent RF from reaching the devices, THAT recom-

mends the circuit of Figure 4. C3 through C5 should

be located close to the point where the input signal

comes into the chassis, preferably directly on the

connector. The unusual circuit design is intended to

minimize the unbalancing impact of differences in

the values of C4 and C5 by forcing the capacitance

from each input to chassis ground to depend primar-

ily on the value of C3. The circuit shown is approxi-

mately ten times less sensitive to mismatches

between C4 and C5 than the more conventional

approach in which the junction of C4 and C5 is

grounded directly. An excellent discussion of input

stage grounding can be found in the June 1995 issue

of the Journal of the Audio Engineering Society, Vol.

43, No. 6, in articles by Stephen Macatee, Bill

Whitlock, and others.

Note that because of the tight matching of the

internal resistor ratios, coupled with the uncertainty

in absolute value of any individual resistor, RF

bypassing through the addition of R-C networks at

the inputs (series resistor followed by a capacitor to

ground at each input) is not recommended. The

added resistors can interact with the internal ones in

unexpected ways. If some impedance for the

RF-bypass capacitor to work against is deemed

necessary, THAT recommends the use of a ferrite

bead or balun instead.

If it is necessary to ac-couple the inputs of the

1290-series parts, the coupling capacitors should be

sized to present negligible impedance at any frequen-

cies of interest for common mode rejection. Regard-

less of the type of coupling capacitor chosen,

variations in the values of the two capacitors,

working against the 1290-series input impedance,

Document 600121 Rev 01 Page 4 of 10 THAT 1290 Series

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

In+ Ref

VCC

VEE

VCC

VEE

R3R4

Figure 3. Representative input protection circuit

470p

47p

In+

In-

Out

100n

VCC

VEE

In-

2/6

In+

3/5

Out 15/11

THAT

1296/

1293/

1290

Ref

Sens

VEE

VCC 14/12

416/10

Figure 4. RFI and supply bypassing

heory of Operation

can unbalance common mode input si

nals. This can

convert common-mode to balanced signals which will

not be rejected by the CMRR of the devices. For this

reason, THAT recommends dc-coupling the inputs of

the 1290-series devices.

Input Voltage Limitations

The 1290 series devices are capable of accepting

input signals above the power supply rails. This is

because the internal opamp’s inputs connect to the

outside world only through the on-chip resistors R1

through R4 at nodes a and b as shown in Figure 2.

Consider the following analysis.

Differential Input Signals

For differential signals (vIN(DIFF)), the limitation to

signal handling will be output clipping. The outputs

of all the devices typically clip at within 2V of the

supply rails. Therefore, maximum differential input

signal levels are directly related to the gain and

supply rails and can be calculated in dBu as follows:

Vin(diff)=20log

VCC−VEE

2−2V

0.775 −Gain

Vin(diff)=20log(VCC −VEE −4V)−Gain −6.8dB

For example, If VCC=15V, VEE=-15V, and

Gain = -3 dB, then

Vin(diff)=20log[15V−(−15V)−4V]−(−3dB)−6.8dB

= 24.5 dBu

Common-Mode Input Signals

For common-mode input signals, there is essen-

tially no output signal. The limitation on common-

mode handling is the point at which the inputs are

overloaded. So, we must consider the inputs of the

opamp.

For common-mode signals (VIN(CM)), the common-mode

input current splits to flow through both R1/R2 and through

R3/R4. Because Vb is constrained to follow Va, we will

consider only the voltage at node a.

The voltage at a can be calculated as:

Va=VIN(CM)

R3+R4

Solving for vIN(CM),

VIN(CM)=VaR3+R4

For the 1290, (R3 + R4) /R4 = 2. For the 1293,

(R3 + R4) /R4 = 2.4. For the 1296, (R3 + R4) /R4 = 3.

Furthermore, the same constraints apply to va as in

the differential analysis.

Following the same reasoning as above, the

maximum common-mode input signal for the 1290 is

(2VCC - 4) V, and the minimum is (2VEE + 4) V. For

the 1293, these figures are (2.4VCC - 4.8) V, and

(2.4VEE + 4.8) V. For the 1296, these figures are

(3VCC - 6) V, and (3VEE + 6) V.

Therefore, for common-mode signals and ±15 V

rails, the 1290 will accept up to ~26 V in either

direction. As an ac signal, this is 52 V peak-peak,

18.4 V rms, or +27.5 dBu. With the same supply

rails, the 1293 will accept up to ~31 V in either

direction. As an ac signal, this is 62 V peak-peak,

21.9 V rms, or +29 dBu. With the same supply rails,

the 1296 will accept up to ~39 V in either direction.

As an ac signal, this is 78 V peak-peak, 27.6 V rms,

or +31 dBu.

Of course, in the real world, differential and

common-mode signals combine. The maximum

signal that can be accommodated will depend on the

superposition of both differential and common-mode

limitations.

Output Considerations

The 1290-series devices are typically capable of

supplying 42 mA into a short circuit. While they will

survive a short, power dissipation will rise dramati-

cally if the output is shorted. Junction temperature

must be kept under 125 ºC to maintain the devices’

specifications.

These devices are stable with up to 200 pF of

load capacitance over the entire rated temperature

range, and even more at room temperature.

Power Supply Considerations

The 1290-series parts are not particularly sensi-

tive to the power supply, but they do contain wide

bandwidth opamps. Accordingly, small local bypass

capacitors should be located within a few inches of

the supply pins on these parts, as shown in Figure 4.

Selecting a Gain Variation

The three different parts offer different gain

structures to suit different applications. The 1296 is

customarily configured for -6 dB gain, but by revers-

ing the resistor connections, it can also be configured

for +6 dB. The 1293 is most often configured for

-3 dB gain, but can also be configured for +3 dB.

The choice of input gain is determined by the input

voltage range to be accommodated, and the power

supply voltages used within the circuit.

To minimize noise and maximize signal-to-noise

ratio, the input stage should be selected and config-

ured for the highest possible gain that will ensure

that maximum-level input signals will not clip the

input stage or succeeding stages. For example, with

±18 V supply rails, the 1290-series parts have a

maximum output signal swing of +23 dBu. In order

to accommodate +24 dBu input signals, the

maximum gain for the stage is -1 dB. With ±15 V

supply rails, the maximum output signal swing is

~+21.1 dBu; here, -3 dB is the maximum gain. In

each case, a 1293 configured for -3 dB gain is the

ideal choice. The 1290 (0 dB gain only) will not

THAT 1290 Series Page 5 of 10 Documen

600121 Rev 01

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

provide enou

h headroom at its output to support a

+24 dBu input signal. The 1296 (configured for -6

dB gain) attenuates the input signal an additional

3 dB, compared to 1293. Although the noise floor of

1296 is 1.5 dB lower than 1293 noise floor, the

reduction in dynamic range is 3 dB - 1.5 dB =

1.5 dB. The 1296 attenuates the input si

nal more

than necessary to support a +24 dBu input.

In fact, for most professional audio applications,

THAT recommends the -3 dB input configuration

possible only with the 1293 in order to preserve

dynamic range within a reasonable range of power

supply voltages and external headroom limits.

Document 600121 Rev 01 Page 6 of 10 THAT 1290 Series

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

The THAT 1290, 1293, and 1296 are usually

thought of as precision differential amplifiers with

gains of zero, -3 and -6 dB respectively. These

devices are primarily intended as balanced line

receivers for audio applications. However, their

topology lends itself to other applications as well.

Basic Balanced Receiver Applications

Figures 5, 6, and 7, respectively, show the 1290,

1293 and 1296 configured as zero, -3 dB, and -6 dB

line receivers. Figures 8 and 9, respectively, show

the 1293 and 1296 configured as +3 dB and +6 dB

line receivers. The higher gains are achieved by

swapping the positions of the resistors within each

pair in regard to signal input vs. output.

Precision Summing Application

Figure 10 shows a 1290 configured as a preci-

sion summing amplifier. This circuit uses both the

In+ and Ref pins as inputs. Because of the good

matching between the resistor pairs, the output

voltage is precisely equal to the sum of the two input

voltages.

Instrumentation Amplifier Application

Figure 11 shows one half of a 1290 configured

as an instrumentation amplifier. The two opamps

preceding the 1290 buffer the input signal before

passing it on to the 1290. The OP270 shown was

chosen for its combination of good ac and dc

performance. In this configuration, the opamps

provide gain equal to 1+(9.98 kΩ / Rg) for differential

signals, but unity gain for common-mode signals.

The 1290 then rejects the common mode signal while

passing on the differential portion. As well, the

opamps buffer the input of the 1290, raising the

circuit’s input impedance to both differential and

common-mode signals. This makes the circuit’s

common-mode rejection less sensitive to variations

in the source impedance driving the stage.

As noted in the Theory of Operation section,

THAT’s InGenius® input stages use patented circuitry

to increase common-mode input impedance. This

even further improves common-mode rejection in

real-world applications. See the THAT 1200-series

datasheet for more information.

THAT 1290 Series Page 7 of 10 Documen

600121 Rev 01

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

Applications

15/11

16/10

3/5

2/6

In+

In- 14/12

9k 9k

1290

Output

Sense

Vout

Ref

VCC

VEE

In+

In-

Figure 5. Zero dB line receiver

15/11

16/10

3/5

2/6

In+

In- 14/12

10.5k 7.5k

1293

Output

Sense

Vout

Ref

VCC

VEE

In+

In-

Figure 6. -3 dB line receiver

15/11

16/10

3/5

2/6

In+

In- 14/12

12k 6k

1296

Output

Sense

Vout

Ref

VCC

VEE

In+

In-

Figure 7. -6 dB line receiver

15/11

16/10

3/5

2/6

In+

In- 14/12

10.5k 7.5k

1293

Out

Sense

Vout

Ref

VCC

VEE

In+

In-

Figure 8. +3 dB line receiver

Driving Analog-to-Digital Converters

Figure 12 shows a convenient method of driving

a typical audio ADC with balanced inputs. This

circuit accepts +24 dBu in. By using both halves of a

single 1293 IC connected in anti-phase, the

maximum signal level between their respective

outputs is +27 dBu. An attenuator network brings

this si

nal down by 18.8 dB while attenuatin

the

noise of the line receivers as well.

In ADC applications such as this, noise is

usually a significant consideration. The output noise

of one channel of a THAT 1293 is -105.5 dBu in a

22 kHz bandwidth, or 27.8 nV/√Hz. Since both

channels are used, and since noise adds in random

fashion (square-root of the sum of the squares), the

total noise level at the input of the resistive pad (R1 ~

R3) will be -102.9 dBu or 37.5 nV/√Hz. The pad

reduces this noise level to -121.3 dBu or 4.5 nV/√Hz

at the input to the ADC, while C1 provides low-pass

filtering typically required by ADCs.

The thermal noise of the resistive attenuator is

1.87 nV/√Hz or the equivalent noise of a 210 Ω resis-

tor. Therefore, the total noise density going into the

input of the ADC will be

en ADC input =(1.87 nV

Hz )2+(4.5 nV

Hz )2=4.87 nV

The noise floor can then be calculated to be

Noise(dBu)=20 log 4.87 nV

Hz %22kHz

0.775 =−120.6 dBu

Controlling Gain in Balanced Systems

When it becomes necessary to control gain in a

balanced system, designers are often tempted to keep

the signal balanced and use two Voltage Controlled

Amplifiers (VCAs) to control the gain on each half of

the balanced signal. Unfortunately, this can result in

common-mode to differential-mode conversion

(degrading CMRR) when there are even slight differ-

ences in gain between the VCAs. A better approach is

to convert the signal to single-ended, alter the gain,

and then convert back to balanced.

Figure 13 shows a stereo gain control for a

balanced system. First, we use a 1293 -3 dB line

receiver to perform the balanced to single-ended

conversion. A THAT 1606, with +6dB gain, is used

to rebalance the signal before the circuit’s output. A

THAT 2162 dual VCA is used to alter gain based on a

dc voltage applied at EC-, the “Control Voltage” node.

(This point is intended to be driven from a

low-impedance, low-noise voltage source. See the

THAT 2162-series data sheet for details.)

As shown, the VCA section is configured for

“static” gain of -3 dB (gain with 0 Vdc applied to the

EC-) due to the choice of ratio of R3 to R2 and R7 to R6.

Additionally, the 1293 has a gain of -3 dB for a total

attenuation of 6 dB before the output driver. The

1606 has a gain of 6 dB, therefore the circuit has a

gain of 0 dB with 0 V at the control voltage node.

This circuit accepts and delivers over +24 dBu

before clipping, and has a noise floor of -91.5 dBu

(22 kHz bandwidth). By varying the Control Voltage,

gains from -70 dB to +40 dB may easily be achieved.

The VCA’s “deci-linear” relationship between Control

Voltage and gain makes the gain setting precise,

predictable, and repeatable.

Document 600121 Rev 01 Page 8 of 10 THAT 1290 Series

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

15/11 Output

16/10

3/5

2/6

Input 1

Input 2

14/12

9k 9k

1290

Sense

Vout

Ref

VCC

VEE

In+

In-

U2A

OP-270

U2B

OP-270

100k

4k99

In+

In-

Out

100n

VCC

VEE

In-

In+

Out 15

THAT1290

Ref

Sens

VEE

VCC 14

416

Figure 11. Instrumentation amplifier

Figure 10. Precision two-input summing circuit

15/11

16/10

3/5

2/6

In+

In- 14/12

12k 6k

1296

Output

Sense

Vout

Ref

VCC

VEE

In+

In-

Figure 9. +6 dB line receiver

THAT 1290 Series Page 9 of 10 Documen

600121 Rev 01

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

Vout 15

In+

In-

U1A

1293

In 1 Hi

In 1 Lo Out 1 Hi

Out 1 Lo

In-

In+

Gnd

In-

In+

Gnd

Out-

Out+

1606

20k0

14k3

N/C

10n

22p

OUT

U3A

2162(VCA1)

U4A

4580

VCC

VEE

Control Voltage 1

6.2mV/dB

-3dB +6dB

Vee

Cap1

Vcc

Cap2

12 4

EC-

EC+

SYM

V+

12 VCC

V+8

VEE

V-4

VCC

V+

Sense

Ref

Vout 11

In+

In-

U1B

1293

In 2 Hi

In 2 Lo Out 2 Hi

Out 2 Lo

Out-

Out+

1606

100n

20k0

14k3

1M0

100n

1M0

10n

22p

10 15

OUT

U3B

2162(VCA2)

U4B

4580

VEE

VCC

VEE

Control Voltage 2

6.2mV/dB

Vee

Cap1

Vcc

Cap2

12 4

GND

EC-

EC+

SYM

V- 5

VEE

V-48

11 14

Sense

Ref

-3dB

Figure 13. Voltage-controlled gain control of a balanced signal

In Hi

In Lo

AIN- to ADC

AIN+ to ADC

-18.8 dB

909R

237R

909R

2n2

+24 dBu In

Vout 15

In+

In-

THAT

1293

Vout 11

In+

In-

1U3A

4580

1/2 Vref of ADC

+27 dBu 2 Vrms Out

Ref

Sense

Ref

Sense

10 THAT

1293

Figure 12. Circuit for audio ADCs with balanced inputs

The THAT1290 series is available in a 16-pin

QSOP package. Package dimensions are shown in

Figure 14 below; Pinouts are given in Table 1 on

page 1. Ordering information is provided in Table 2

below.

The 1290 series package is entirely lead-free.

The lead-frame is copper, plated with successive

layers of nickel, palladium, and gold. This approach

makes it possible to solder these devices using lead-

free and lead-bearing solders.

Neither the lead-frame nor the plastic mold

compound used in the 1290-series contains any

hazardous substances as specified in the European

Union's Directive on the Restriction of the Use of

Certain Hazardous Substances in Electrical and

Electronic Equipment 2002/95/EG of January 27,

2003.

The surface-mount package is suitable for use in

a 100% tin solder process.

Document 600121 Rev 01 Page 10 of 10 THAT 1290 Series

Low Cost Dual Balanced Line Receivers

THAT Corporation; 45 Sumner Street; Milford, MA 01757-1656; USA

Tel: +1 508 478 9200; Fax: +1 508 478 0990; Web: www.thatcorp.com

0-8º

ITEM MILLIMETERS INCHES

A4.80 - 4.98 0.189 - 0.196

B3.81 - 3.99 0.150 - 0.157

C5.79 - 6.20 0.228 - 0.244

D0.20 - 0.30 0.008 - 0.012

E0.635 BSC 0.025 BSC

G1.35 - 1.75 0.0532 - 0.0688

H0.10 - 0.25 0.004 - 0.010

I0.40 - 1.27 0.016 - 0.050

J0.19 - 0.25 0.0075 - 0.0098

Figure 14. 16-pin QSOP package outline

Parameter Symbol Conditions Min Typ Max Units

Package Style See Fig. 14 for dimensions 16 Pin QSOP

Thermal Resistance θJA QSOP package soldered to board 115 ºC/W

Environmental Regulation Compliance Complies with January 27, 2003 RoHS requirements

Soldering Reflow Profile JEDEC JESD22-A113-D (250 ºC)

Moisture Sensitivity Level MSL Above-referenced JEDEC soldering profile 1

Package Characteristics

1296Q16-U

±6 dB

1293Q16-U

±3 dB

1290Q16-U0 dB

Order NumberGain

Table 2. Ordering information

Package Information