EL2126 (R) Data Sheet May 2, 2007 Ultra-Low Noise, Low Power, Wideband Amplifier The EL2126 is an ultra-low noise, wideband amplifier that runs on half the supply current of competitive parts. It is intended for use in systems such as ultrasound imaging where a very small signal needs to be amplified by a large amount without adding significant noise. Its low power dissipation enables it to be packaged in the tiny SOT-23 package, which further helps systems where many input channels create both space and power dissipation problems. The EL2126 is stable for gains of 10 and greater and uses traditional voltage feedback. This allows the use of reactive elements in the feedback loop, a common requirement for many filter topologies. It operates from 2.5V to 15V supplies and is available in the 5 Ld SOT-23 and 8 Ld SO packages. The EL2126 is fabricated in Elantec's proprietary complementary bipolar process, and is specified for operation over the full -40C to +85C temperature range. FN7046.4 Features * Voltage noise of only 1.3nV/Hz * Current noise of only 1.2pA/Hz * 200V offset voltage * 100MHz -3dB BW for AV = 10 * Very low supply current - 4.7mA * SOT-23 package * 2.5V to 15V operation * Pb-free plus anneal available (RoHS compliant) Applications * Ultrasound input amplifiers * Wideband instrumentation * Communication equipment * AGC and PLL active filters * Wideband sensors Pinouts EL2126 (5 LD SOT-23) TOP VIEW OUT 1 5 VS+ VS- 2 + - IN+ 3 4 IN- EL2126 (8 LD SOIC) TOP VIEW 8 NC NC 1 IN- 2 IN+ 3 7 VS+ + 6 OUT 5 NC VS- 4 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2002, 2005, 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. EL2126 Ordering Information PART NUMBER PART MARKING TEMP RANGE (C) TAPE AND REEL PACKAGE PKG. DWG. # EL2126CW-T7 G -40 to +85 7" (3k pcs) 5 Ld SOT-23 MDP0038 EL2126CW-T7A G -40 to +85 7" (250 pcs) 5 Ld SOT-23 MDP0038 EL2126CS 2126CS -40 to +85 - 8 Ld SOIC (150 mil) MDP0027 EL2126CS-T7 2126CS -40 to +85 7" 8 Ld SOIC (150 mil) MDP0027 EL2126CS-T13 2126CS -40 to +85 13" 8 Ld SOIC (150 mil) MDP0027 EL2126CSZ ( Note) 2126CSZ -40 to +85 - 8 Ld SOIC (150 mil) (Pb-free) MDP0027 EL2126CSZ-T7 ( Note) 2126CSZ -40 to +85 7" 8 Ld SOIC (150 mil) (Pb-free) MDP0027 EL2126CSZ-T13 ( Note) 2126CSZ -40 to +85 13" 8 Ld SOIC (150 mil) (Pb-free) MDP0027 EL2126CWZ-T7 (Note) BAAH -40 to +85 7" 5 Ld SOT-23 (SC74) (1.65mm) (Green) P5.064 EL2126CWZ-T7A (Note) BAAH -40 to +85 7" 5 Ld SOT-23 (SC74) (1.65mm) (Green) P5.064 NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN7046.4 May 2, 2007 EL2126 Absolute Maximum Ratings Thermal Information VS+ to VS-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33V Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 40mA Any Input . . . . . . . . . . . . . . . . . . . . . . . . . . . VS+ -0.3V to VS- +0.3V Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40C to +85C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-60C to +150C Maximum Die Junction Temperature . . . . . . . . . . . . . . . . . . . +150C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications Parameter VS+ = +5V, VS- = -5V, TA = +25C, RF = 180, RG = 20, RL = 500 Unless Otherwise Specified. Description Conditions Min Typ Max Unit 0.2 2 mV 3 mV DC PERFORMANCE VOS Input Offset Voltage (SO8) Input Offset Voltage (SOT23-5) TCVOS Offset Voltage Temperature Coefficient IB Input Bias Current IOS Input Bias Current Offset 0.06 TCIB Input Bias Current Temperature Coefficient 0.013 A/C CIN Input Capacitance 2.2 pF AVOL Open Loop Gain 80 87 dB PSRR Power Supply Rejection Ratio (Note 1) 80 100 dB CMRR Common Mode Rejection Ratio 75 106 dB CMIR Common Mode Input Range VOUTH Positive Output Voltage Swing No load, RF = 1k VOUTL Negative Output Voltage Swing No load, RF = 1k VOUTH2 Positive Output Voltage Swing RL = 100 VOUTL2 Negative Output Voltage Swing RL = 100 IOUT Output Short Circuit Current (Note 2) ISY Supply Current -10 VO = -2.5V to +2.5V at CMIR 17 V/C -7 A -4.6 3.8 3.8 3.8 -4 3.2 -3.9 V V V -3.2 100 4.7 A V 3.45 -3.5 80 0.6 V mA 5.5 mA AC PERFORMANCE - RG = 20, CL = 3pF BW -3dB Bandwidth, RL = 500 100 MHz BW 0.1dB 0.1dB Bandwidth, RL = 500 17 MHz BW 1dB 1dB Bandwidth, RL = 500 80 MHz Peaking Peaking, RL = 500 0.6 dB SR Slew Rate VOUT = 2VP-P, measured at 20% to 80% 110 V/s OS Overshoot, 4VP-P Output Square Wave Positive 2.8 % Negative -7 % 51 ns tS Settling Time to 0.1% of 1V Pulse 3 80 FN7046.4 May 2, 2007 EL2126 Electrical Specifications Parameter VS+ = +5V, VS- = -5V, TA = +25C, RF = 180, RG = 20, RL = 500 Unless Otherwise Specified. Description Conditions Min Typ Max Unit VN Voltage Noise Spectral Density 1.3 nV/Hz IN Current Noise Spectral Density 1.2 pA/Hz HD2 2nd Harmonic Distortion (Note 3) -70 dBc HD3 3rd Harmonic Distortion (Note 3) -70 dBc NOTES: 1. Measured by moving the supplies from 4V to 6V 2. Pulse test only and using a 10 load 3. Frequency = 1MHz, VOUT = 2VP-P, into 500 and 5pF load VS+ = +15V, VS- = -15V, TA = 25C, RF = 180, RG = 20, RL = 500 unless otherwise specified. Electrical Specifications Parameter Description Conditions Min Typ Max Unit 0.5 3 mV 3 mV DC PERFORMANCE VOS Input Offset Voltage (SO8) Input Offset Voltage (SOT23-5) TCVOS Offset Voltage Temperature Coefficient IB Input Bias Current IOS Input Bias Current Offset 0.12 TCIB Input Bias Current Temperature Coefficient 0.016 A/C CIN Input Capacitance 2.2 pF AVOL Open Loop Gain 80 90 dB PSRR Power Supply Rejection Ratio (Note 4) 65 80 dB CMRR Common Mode Rejection Ratio 70 85 dB CMIR Common Mode Input Range VOUTH Positive Output Voltage Swing No load, RF = 1k VOUTL Negative Output Voltage Swing No load, RF = 1k VOUTH2 Positive Output Voltage Swing RL = 100, RF = 1k VOUTL2 Negative Output Voltage Swing RL = 100, RF = 1k IOUT Output Short Circuit Current (Note 5) ISY Supply Current -10 at CMIR 4.5 V/C -7 A -14.6 13.6 13.8 13.7 -13.8 10.2 -13.7 V V V -9.5 220 5 A V 11.2 -10.3 140 0.7 V mA 6 mA AC PERFORMANCE - RG = 20, CL = 3pF BW -3dB Bandwidth, RL = 500 135 MHz BW 0.1dB 0.1dB Bandwidth, RL = 500 26 MHz BW 1dB 1dB Bandwidth, RL = 500 60 MHz Peaking Peaking, RL = 500 2.1 dB SR Slew Rate (2.5V Square Wave, Measured 25%-75%) 150 V/S OS Overshoot, 4VP-P Output Square Wave Positive 1.6 % Negative -4.4 % 48 ns TS Settling Time to 0.1% of 1V Pulse 4 130 FN7046.4 May 2, 2007 EL2126 VS+ = +15V, VS- = -15V, TA = 25C, RF = 180, RG = 20, RL = 500 unless otherwise specified. (Continued) Electrical Specifications Parameter Description Conditions Min Typ Max Unit VN Voltage Noise Spectral Density 1.4 nV/Hz IN Current Noise Spectral Density 1.1 pA/Hz HD2 2nd Harmonic Distortion (Note 6) -72 dBc HD3 3rd Harmonic Distortion (Note 6) -73 dBc NOTES: 4. Measured by moving the supplies from 13.5V to 16.5V 5. Pulse test only and using a 10 load 6. Frequency = 1MHz, VOUT = 2VP-P, into 500 and 5pF load Typical Performance Curves 10 VS = 5V AV = 10 CL = 5pF RL = 500 6 RF = 1k RF = 500 2 -2 RF = 180 -6 RF = 100 -10 1M 10M NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 10 6 VS = 15V AV = 10 CL = 5pF RL = 500 -2 RF = 180 RF = 100 -6 10M FREQUENCY (Hz) FIGURE 2. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS RF 8 8 VS = 5V AV = -10 CL = 5pF RL = 500 RF = 500 RF = 1k NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 100M FREQUENCY (Hz) FIGURE 1. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS RF 4 RF = 500 2 -10 1M 100M RF = 1k RF = 350 0 -4 RF = 200 RF = 100 -8 -12 1M 10M 100M FREQUENCY (Hz) FIGURE 3. INVERTING FREQUENCY RESPONSE FOR VARIOUS RF 5 4 VS = 15V AV = -10 CL = 5pF RL = 500 RF = 1k RF = 500 RF = 350 0 -4 RF = 200 RF = 100 -8 -12 1M 10M 100M FREQUENCY (Hz) FIGURE 4. INVERTING FREQUENCY RESPONSE FOR VARIOUS RF FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) 10 VS = 5V RG = 20 RL = 500 CL = 5pF 6 2 AV = 10 AV = 20 -2 AV = 50 -6 -10 1M 10M NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 10 6 VS = 15V RG = 20 RL = 500 CL = 5pF AV = 10 2 AV = 20 -2 AV = 50 -6 -10 1M 100M 10M FREQUENCY (Hz) FIGURE 5. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS GAIN FIGURE 6. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS GAIN 8 VS = 5V CL = 5pF RG = 35 4 0 AV = -10 -4 AV = -50 AV = -20 -8 -12 1M 10M NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 8 VS = 15V CL = 5pF RG = 20 4 0 AV = -10 -4 AV = -50 -12 1M 100M 10M 100M FREQUENCY (Hz) FIGURE 7. INVERTING FREQUENCY RESPONSE FOR VARIOUS GAIN FIGURE 8. INVERTING FREQUENCY RESPONSE FOR VARIOUS RF 10 VS = 5V CL = 5pF RL = 500 RF = 180 AV = 10 0 -4 -8 -12 1M VO = 500mVPP VO = 30mVPP VO = 5VPP VO = 2.5VPP VO = 1VPP 10M 100M FREQUENCY (Hz) FIGURE 9. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS OUTPUT SIGNAL LEVELS 6 NORMALIZED GAIN (dB) 8 NORMALIZED GAIN (dB) AV = -20 -8 FREQUENCY (Hz) 4 100M FREQUENCY (Hz) 6 VS = 15V CL = 5pF RL = 500 RF = 180 AV = 10 VO = 30mVPP VO = 500mVPP 2 -2 -6 -10 1M VO = 1VPP VO = 10VPP VO = 5VPP VO = 2.5VPP 10M 100M FREQUENCY (Hz) FIGURE 10. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS OUTPUT SIGNAL LEVELS FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) 4 8 VS = 5V CL = 5pF RL = 500 RF = 350 AV = 10 VO = 500mVPP VO = 30mVPP VO = 1VPP 0 VO = 3.4VPP -4 VO = 2.5VPP -8 -12 1M 10M NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 8 4 VS = 15V CL = 5pF RL = 500 RF = 200 AV = 10 VO = 3.4VPP -4 VOV=O2.5V =2.5V PPP -8 10M FREQUENCY (Hz) FIGURE 12. INVERTING FREQUENCY RESPONSE FOR VARIOUS OUTPUT SIGNAL LEVELS 10 VS = 5V RF = 150 AV = 10 RL = 500 6 CL = 28pF CL = 11pF 2 CL = 16pF CL = 5pF -2 CL = 1pF -6 -10 1M 10M NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 10 6 VS = 15V RF = 180 AV = 10 RL = 500 CL = 11pF CL = 16pF CL = 5pF -2 CL = 1.2pF -6 -10 1M 100M CL = 28pF 2 10M 100M FREQUENCY (Hz) FREQUENCY (Hz) FIGURE 13. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS CL FIGURE 14. NON-INVERTING FREQUENCY RESPONSE FOR VARIOUS CL 8 8 VS = 5V RF = 350 RL = 500 AV = -10 CL = 28pF CL = 16pF 0 CL = 11pF -4 CL = 5pF CL = 1.2pF -8 -12 1M 10M 100M FREQUENCY (Hz) FIGURE 15. INVERTING FREQUENCY RESPONSE FOR VARIOUS CL 7 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 100M FREQUENCY (Hz) FIGURE 11. INVERTING FREQUENCY RESPONSE FOR VARIOUS OUTPUT SIGNAL LEVELS 4 VO = 30mVPP VO = 1VPP 0 -12 1M 100M VO = 500mVPP 4 VS = 15V RF = 200 RL = 500 AV = -10 CL = 28pF CL = 16pF 0 CLC=L=11p 11pF -4 CL = 5pF CL = 1.2pF -8 -12 1M 10M 100M FREQUENCY (Hz) FIGURE 16. INVERTING FREQUENCY RESPONSE FOR VARIOUS CL FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) 100 250 OPEN LOOP GAIN (dB) PHASE 60 50 40 -50 20 -150 VS=5V 0 10k 100k 1M 10M SUPPLY CURRENT (mA) 150 80 OPEN LOOP PHASE () GAIN 0.6/DIV -250 1G 100M 0 0 1.5/DIV SUPPLY VOLTAGE (V) FREQUENCY (Hz) FIGURE 17. OPEN LOOP GAIN AND OPEN LOOP PHASE FIGURE 18. SUPPLY CURRENT vs SUPPLY VOLTAGE 3.0 160 VS = 5V RG = 20 RL = 500 CL = 5pF 120 AV = -10 AV = 10 100 80 AV = -20 60 40 AV = -20 AV = -50 20 AV = 50 0 0 2 4 6 8 10 VS = 5V RG = 20 RL = 500 CL = 5pF 2.5 PEAKING (dB) -3dB BANDWIDTH 140 12 14 2.0 AV = 10 1.5 1.0 0.5 AV = -10 0 16 0 4 6 8 10 12 14 16 FIGURE 20. PEAKING vs Vs FIGURE 19. BANDWIDTH vs Vs RF = 180 RG = 20 2 SUPPLY VOLTAGE (V) VS (V) VS = 5V VO = 2VPP 0.5V/DIV 20mV/DIV RF = 180 RG = 20 VS = 5V VO = 100mVPP 10ns/DIV FIGURE 21. LARGE SIGNAL STEP RESPONSE 8 10ns/DIV FIGURE 22. SMALL SIGNAL STEP RESPONSE FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) -30 VS = 5V VO = 2VP-P RF = 180 AV = 10 RL = 500 -50 -60 HARMONIC DISTORTION (dBc) HARUMONIC DISTORTION (dBc) -40 2nd HD -70 -80 3rd HD -90 -100 VS = 5V VO = 2VP-P RF = 180 AV = 10 RL = 500 -40 -50 -60 -70 3rd HD -80 -90 -100 0 1 2 3 4 5 6 7 8 0 5 10 VOUT (VP-P) 20 25 FIGURE 24. 1MHz HARMONIC DISTORTION vs OUTPUT SWING -20 10 VS = 5V VO = 2VP-P IN (pA/Hz), VN (nV/Hz) -30 15 VOUT (VP-P) FIGURE 23. 1MHz HARMONIC DISTORTION vs OUTPUT SWING -40 THD (dBc) 2nd HD -50 -60 -70 IN, VS = 5V VN, VS = 15V VN, VS = 5V -80 -90 1k 10k 100k 1M 10M 1 10 100M IN, VS = 15V 100 FREQUENCY (Hz) FIGURE 25. TOTAL HARMONIC DISTORTION vs FREQUENCY 40 30 20 100k 16 VS = 5 V ,V VS = 15 V, V VS = 5V ,V VS = 15V ,V 12 O=5 VP -P GROUP DELAY (ns) SETTLING TIME (ns) 50 10k FIGURE 26. NOISE vs FREQUENCY 70 60 1k FREQUENCY (Hz) O=5 VP -P O=2 VP -P O=2 VP -P VS = 5V RL = 500 AV = 10 8 4 AV = -10 0 10 0 0.1 1.0 10.0 ACCURACY (%) FIGURE 27. SETTLING TIME vs ACCURACY 9 -4 1M 10M 100M 400M FREQUENCY (Hz) FIGURE 28. GROUP DELAY vs FREQUENCY FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) -10 110 VS=5V 90 PSRR (dB) -50 -70 PSRR- 70 50 -90 PSRR+ 30 -110 10 100 1k 10k 100k 1M 10M 10 10k 100M 100k FREQUENCY (Hz) FIGURE 29. CMRR vs FREQUENCY CLOSED LOOP OUTPUT IMPEDANCE () 1M 10M 200M FREQUENCY (Hz) FIGURE 30. PSRR vs FREQUENCY 3.5 120 100 VS = 5V VS = 5V 3 100 2.5 BANDWIDTH (MHz) 10 1 0.1 80 BANDWIDTH 2 1.5 60 1 40 PEAKING 0.5 20 0.01 10k 1M 100k 0 0 -40 100M 10M FREQUENCY (Hz) -0.5 0 40 80 120 160 TEMPERATURE (C) FIGURE 31. CLOSED LOOP OUTPUT IMPEDANCE vs FREQUENCY FIGURE 32. BANDWIDTH AND PEAKING vs TEMPERATURE 5.2 220 15VSR- 200 VS=15V 5.1 180 160 15VSR+ IS (mA) SLEW RATE (V/s) PEAKING (dB) CMRR (dB) -30 140 120 5 VS=5V 5VSR- 100 4.9 5VSR+ 80 60 -1 1 3 5 7 9 11 13 VOUT SWING (VPP) FIGURE 33. SLEW RATE vs SWING 10 15 4.8 -50 0 50 100 150 DIE TEMPERATURE (C) FIGURE 34. SUPPLY CURRENT vs TEMPERATURE FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) 1 120 VS = 5V 110 CMRR (dB) VOS (mV) 0 VS = 15V VS = 5V 100 -1 90 -2 -50 0 50 100 80 -50 150 DIE TEMPERATURE (C) 0 50 100 150 DIE TEMPERATURE (C) FIGURE 35. OFFSET VOLTAGE vs TEMPERATURE FIGURE 36. CMRR vs TEMPERATURE 110 4.05 106 4 VS = 5V VOUTH (V) PSRR (dB) 102 98 94 3.95 VS = 5V 3.9 90 VS = 15V 3.85 86 82 -50 0 50 100 3.8 -50 150 DIE TEMPERATURE (C) 0 50 100 150 DIE TEMPERATURE (C) FIGURE 37. PSRR vs TEMPERATURE FIGURE 38. POSITIVE OUTPUT SWING vs TEMPERATURE 13.85 -3.9 -3.95 13.8 VOUTL (V) VOUTH (V) -4 VS = 15V 13.75 13.7 VS = 5V -4.05 -4.1 -4.15 13.65 -4.2 13.6 -50 0 50 100 150 DIE TEMPERATURE (C) FIGURE 39. POSITIVE OUTPUT SWING vs TEMPERATURE 11 -4.25 -50 0 50 100 150 DIE TEMPERATURE (C) FIGURE 40. NEGATIVE OUTPUT SWING vs TEMPERATURE FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) -13.76 102 SLEW RATE (V/s) 100 VOUTL (V) -13.78 VS = 15V -13.8 VS = 5V 98 96 94 92 90 -13.82 -50 0 50 100 88 -50 150 DIE TEMPERATURE (C) 150 3.5 VS = 15V VOUTH2 (V) SR (V/s) 3.52 145 140 150 VS = 5V 3.48 3.46 VO = 2VPP 0 50 100 3.44 -50 150 DIE TEMPERATURE (C) 0 50 100 150 DIE TEMPERATURE (C) FIGURE 43. SLEW RATE vs TEMPERATURE FIGURE 44. POSITIVE LOADED OUTPUT SWING vs TEMPERATURE 11.8 -3.35 11.6 -3.4 VS = 15V VOUTL2 (V) 11.4 SR (V/s) 100 FIGURE 42. SLEW RATE vs TEMPERATURE 155 11.2 11 -3.45 -3.5 VS = 5V 3.55 10.8 10.6 -50 50 DIE TEMPERATURE (C) FIGURE 41. NEGATIVE OUTPUT SWING vs TEMPERATURE 135 -50 0 0 50 100 150 DIE TEMPERATURE (C) FIGURE 45. POSITIVE LOADED OUTPUT SWING vs TEMPERATURE 12 -3.6 -50 0 50 100 150 DIE TEMPERATURE (C) FIGURE 46. NEGATIVE LOADED OUTPUT SWING vs TEMPERATURE FN7046.4 May 2, 2007 EL2126 Typical Performance Curves (Continued) -9.4 VOUTL2 (V) -9.6 -9.8 VS=15V -10 -10.2 -10.4 -10.6 -50 0 50 100 150 Die Temperature (C) FIGURE 47. NEGATIVE LOADED OUTPUT SWING vs TEMPERATURE JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1.8 1.6 1 POWER DISSIPATION (W) POWER DISSIPATION (W) 1.2 781mW 0.8 J A= +1 0.6 488mW 0.4 0.2 SO 8 60 C /W SO T23 J -5 A=+ 256 C/W 1.4 1.2 1.136W J 1 0.6 543mW 0.4 0.2 0 0 25 50 75 85 100 125 150 AMBIENT Temperature (C) FIGURE 48. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 13 SO A= +1 0.8 8 10 C /W SOT 23-5 J A = +2 30C /W 0 0 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (C) FIGURE 49. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE FN7046.4 May 2, 2007 EL2126 Pin Descriptions EL2126CW (5 Ld SOT-23) EL2126CS ( 8 Ld SOIC) PIN NAME PIN FUNCTION 1 6 VOUT Output EQUIVALENT CIRCUIT VS+ VOUT Circuit 1 2 4 VS- Supply 3 3 VINA+ Input VS+ VIN+ VIN- VSCircuit 2 4 2 VINA- Input 5 7 VS+ Supply 14 Reference Circuit 2 FN7046.4 May 2, 2007 EL2126 Applications Information Noise Calculations Product Description The EL2126 is an ultra-low noise, wideband monolithic operational amplifier built on Elantec's proprietary high speed complementary bipolar process. It features 1.3nV/Hz input voltage noise, 200V typical offset voltage, and 73dB THD. It is intended for use in systems such as ultrasound imaging where very small signals are needed to be amplified. The EL2126 also has excellent DC specifications: 200V VOS, 22A IB, 0.4A IOS, and 106dB CMRR. These specifications allow the EL2126 to be used in DC-sensitive applications such as difference amplifiers. The primary application for the EL2126 is to amplify very small signals. To maintain the proper signal-to-noise ratio, it is essential to minimize noise contribution from the amplifier. Figure 51 shows all the noise sources for all the components around the amplifier. VIN R3 VR3 VR1 IN- VON R1 VR2 R2 The EL2126 has a gain-bandwidth product of 650MHz at 5V. For gains less than 20, higher-order poles in the amplifier's transfer function contribute to even higher closedloop bandwidths. For example, the EL2126 has a -3dB bandwidth of 100MHz at a gain of 10 and decreases to 33MHz at gain of 20. It is important to note that the extra bandwidth at lower gain does not come at the expenses of stability. Even though the EL2126 is designed for gain 10. With external compensation, the device can also operate at lower gain settings. The RC network shown in Figure 50 reduces the feedback gain at high frequency and thus maintains the amplifier stability. R values must be less than RF divided by 9 and 1 divided by 2RC must be less than 200MHz. RF FIGURE 51. VN is the amplifier input voltage noise IN+ is the amplifier positive input current noise IN- is the amplifier negative input current noise VRX is the thermal noise associated with each resistor: V RX = 4kTRx (EQ. 1) where: k is Boltzmann's constant = 1.380658 x 10-23 T is temperature in degrees Kelvin (273 + C) R + + - IN+ Gain-Bandwidth Product C VN VOUT The total noise due to the amplifier seen at the output of the amplifier can be calculated by using the Equation 2. VIN FIGURE 50. Choice of Feedback Resistor, RF The feedback resistor forms a pole with the input capacitance. As this pole becomes larger, phase margin is reduced. This increases ringing in the time domain and peaking in the frequency domain. Therefore, RF has some maximum value which should not be exceeded for optimum performance. If a large value of RF must be used, a small capacitor in the few pF range in parallel with RF can help to reduce this ringing and peaking at the expense of reducing the bandwidth. Frequency response curves for various RF values are shown in the typical performance curves section of this data sheet. V ON = As the equation shows, to keep noise at a minimum, small resistor values should be used. At higher amplifier gain configuration where R2 is reduced, the noise due to IN-, R2, and R1 decreases and the noise caused by IN+, VN, and R3 starts to dominate. Because noise is summed in a rootmean-squares method, noise sources smaller than 25% of the largest noise source can be ignored. This can greatly simplify the formula and make noise calculation much easier to calculate. R 1 2 R 1 2 R 1 2 R 1 2 2 2 2 2 2 BW x VN x 1 + ------- + IN- x R 1 + IN+ x R 3 x 1 + ------- + 4 x K x T x R 1 + 4 x K x T x R 2 x ------- + 4 x K x T x R 3 x 1 + ------- R 2 R 2 R 2 R 2 (EQ. 2) 15 FN7046.4 May 2, 2007 EL2126 Output Drive Capability The EL2126 is designed to drive low impedance load. It can easily drive 6VP-P signal into a 100 load. This high output drive capability makes the EL2126 an ideal choice for RF, IF, and video applications. Furthermore, the EL2126 is current-limited at the output, allowing it to withstand momentary short to ground. However, the power dissipation with output-shorted cannot exceed the power dissipation capability of the package. Driving Cables and Capacitive Loads Although the EL2126 is designed to drive low impedance load, capacitive loads will decreases the amplifier's phase margin. As shown in the performance curves, capacitive load can result in peaking, overshoot and possible oscillation. For optimum AC performance, capacitive loads should be reduced as much as possible or isolated with a series resistor between 5 to 20. When driving coaxial cables, double termination is always recommended for reflection-free performance. When properly terminated, the capacitance of the coaxial cable will not add to the capacitive load seen by the amplifier. Power Supply Bypassing And Printed Circuit Board Layout As with any high frequency devices, good printed circuit board layout is essential for optimum performance. Ground plane construction is highly recommended. Lead lengths should be kept as short as possible. The power supply pins must be closely bypassed to reduce the risk of oscillation. The combination of a 4.7F tantalum capacitor in parallel 16 with 0.1F ceramic capacitor has been proven to work well when placed at each supply pin. For single supply operation, where pin 4 (VS-) is connected to the ground plane, a single 4.7F tantalum capacitor in parallel with a 0.1F ceramic capacitor across pins 7 (VS+) and pin 4 (VS-) will suffice. For good AC performance, parasitic capacitance should be kept to a minimum. Ground plane construction again should be used. Small chip resistors are recommended to minimize series inductance. Use of sockets should be avoided since they add parasitic inductance and capacitance which will result in additional peaking and overshoot. Supply Voltage Range and Single Supply Operation The EL2126 has been designed to operate with supply voltage range of 2.5V to 15V. With a single supply, the EL2126 will operate from +5V to +30V. Pins 4 and 7 are the power supply pins. The positive power supply is connected to pin 7. When used in single supply mode, pin 4 is connected to ground. When used in dual supply mode, the negative power supply is connected to pin 4. As the power supply voltage decreases from +30V to +5V, it becomes necessary to pay special attention to the input voltage range. The EL2126 has an input voltage range of 0.4V from the negative supply to 1.2V from the positive supply. So, for example, on a single +5V supply, the EL2126 has an input voltage range which spans from 0.4V to 3.8V. The output range of the EL2126 is also quite large, on a +5V supply, it swings from 0.4V to 3.8V. FN7046.4 May 2, 2007 EL2126 Small Outline Package Family (SO) A D h X 45 (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL "X" 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4 4 DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300") (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150") 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006" maximum per side are not included. 2. Plastic interlead protrusions of 0.010" maximum per side are not included. 3. Dimensions "D" and "E1" are measured at Datum Plane "H". 4. Dimensioning and tolerancing per ASME Y14.5M-1994 17 FN7046.4 May 2, 2007 EL2126 Small Outline Transistor Plastic Packages (SOT23-5) P5.064 D 5 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE VIEW C e1 INCHES 5 SYMBOL 4 E CL 1 2 CL 3 e E1 b CL 0.20 (0.008) M C C CL A A2 SEATING PLANE A1 -C- WITH b PLATING b1 c c1 MILLIMETERS MAX MIN MAX NOTES A 0.036 0.057 0.90 1.45 - A1 0.000 0.0059 0.00 0.15 - A2 0.036 0.051 0.90 1.30 - b 0.012 0.020 0.30 0.50 - b1 0.012 0.018 0.30 0.45 c 0.003 0.009 0.08 0.22 6 c1 0.003 0.008 0.08 0.20 6 D 0.111 0.118 2.80 3.00 3 E 0.103 0.118 2.60 3.00 - E1 0.060 0.067 1.50 1.70 3 e 0.0374 Ref 0.95 Ref - e1 0.0748 Ref 1.90 Ref - L 0.10 (0.004) C MIN 0.014 0.022 0.35 0.55 L1 0.024 Ref. 0.60 Ref. L2 0.010 Ref. 0.25 Ref. N 5 5 4 5 R 0.004 - 0.10 - R1 0.004 0.010 0.10 0.25 0o 8o 0o 8o Rev. 2 9/03 NOTES: BASE METAL 1. Dimensioning and tolerance per ASME Y14.5M-1994. 2. Package conforms to EIAJ SC-74 and JEDEC MO178AA. 4X 1 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. R1 4. Footlength L measured at reference to gauge plane. 5. "N" is the number of terminal positions. R GAUGE PLANE SEATING PLANE L C L1 L2 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. 4X 1 VIEW C 18 FN7046.4 May 2, 2007 EL2126 SOT-23 Package Family MDP0038 e1 SOT-23 PACKAGE FAMILY D A MILLIMETERS 6 N SYMBOL 4 E1 2 E 3 0.15 C D 1 2X 2 3 0.20 C 5 2X e 0.20 M C A-B D B b NX 0.15 C A-B 1 3 SOT23-5 SOT23-6 TOLERANCE A 1.45 1.45 MAX A1 0.10 0.10 0.05 A2 1.14 1.14 0.15 b 0.40 0.40 0.05 c 0.14 0.14 0.06 D 2.90 2.90 Basic E 2.80 2.80 Basic E1 1.60 1.60 Basic e 0.95 0.95 Basic e1 1.90 1.90 Basic L 0.45 0.45 0.10 L1 0.60 0.60 Reference N 5 6 Reference Rev. F 2/07 D 2X NOTES: C A2 SEATING PLANE 1. Plastic or metal protrusions of 0.25mm maximum per side are not included. 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. A1 0.10 C 3. This dimension is measured at Datum Plane "H". NX 4. Dimensioning and tolerancing per ASME Y14.5M-1994. 5. Index area - Pin #1 I.D. will be located within the indicated zone (SOT23-6 only). (L1) 6. SOT23-5 version has no center lead (shown as a dashed line). H A GAUGE PLANE c L 0.25 0 +3 -0 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 19 FN7046.4 May 2, 2007