DATE CHECKED APR.-04-`03 APR.-04-`03 Device Name Type Name PA905C6R Spec. No. MS5D1753 No t NAME DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. S P E C I F I C AT I O N SILICON DIODE de ew n for APPROVED DRAWN APR.-04-`03 n sig MS5D1753 . nd e mm o c e r Fuji Electric Co.,Ltd. Matsumoto Factory Fuji Electric Co.,Ltd. 1/12 H04-004-07 Date APR.-04 -2003 No t Fuji Electric Co.,Ltd. DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. Revised Records Classification Ind. Content Applied date Drawn enactment Issued date ew n for Checked de MS5D1753 Approved n sig . nd e mm o c e r 2/12 H04-004-06 1. SCOPE This specification provides the ratings and the test requirement for FUJI SILICON DIODE PA905C6R 2. OUT VIEW, MARKING, MOLDING RESIN, CHARACTERISTICS (1) Out view is shown MS5D1753 9/12 (2) Marking is shown MS5D1753 9/12 It is marked to type name or abbreviated type name, polarity and Lot No. (3) Molding resin Epoxy resin UL:V-0 (4) Characteristics is shown MS5D1753 10/12~12/12 4. RATINGS 4.1 MAXIMUM RATINGS ITEM SYMBOL Repetitive peak reverse voltage VRRM Non-repetitive peak reverse voltage VRSM I0 m Non-repetitive surge current d Tjn e m Operating junction temperature t No IFSM o c e r 600 . V w ne 20 * A 120 A 150 C -40~150 C n 600 sig 106 Sine wave, 10ms Tstg V * Out put current of centertap full wave connection. 4.2 ELECTRICAL CHARACTERISTICS ITEM Square wave duty =1/2 Tc = RATINGS UNITS de for Average output current Storage temperature CONDITIONS (at Ta=25 unless otherwise specified.) CONDITIONS SYMBOL MAXIMUM UNITS Forward voltage VF IF = 10 A 1.7 V Reverse current IR VR = VRRM 100 A Reverse recovery time trr IF=0.1A,IR=0.2,Irec=0.05A 50 ns 1.2 C/W 0.40.6 Nm 5.0 g Thermal resistance Rth(j-c) Junction to case 4.3 MECHANICAL CHARACTERISTICS Mounting torque Recommended torque Approximate mass Fuji Electric Co.,Ltd. DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. 3.LEAD AND LABEL (1) Outer lead:material:Sn-0.7Cu(diping) (2) LABEL:Pb Free Mark MS5D1753 3/12 H04-004-03 5. TEST AND INSPECTION 5.1 STANDARD TEST CONDITION Standard test condition Is Ta=25RH=65%. If judgement Is no doubt,the test condition Is possible to test In normal condition Ta=535RH=4885% 5.2 STRUCTURE INSPECTION It inspect with eye and measure,Item2 shall be satisfied. 5.3 FORWARD AND REVERSE CHARACTERISTICS It inspect on the standard condition,Item4.2 shall be satisfied. 5.4 TEST Test Test No. Items Testing methods and Conditions 2 Terminal Strength (Bending) 4 Vibration 6 Solderability 1 nd e mm t No Solderability 2 7 Resistance to Soldering Heat A-111A method 1 5 A-111A method 3 5 A-112 method 2 ew n for o c e r Fuji Electric Co.,Ltd. DWG.NO. 5 Shock Pull force TO-220,TO-220F : 10N TO-3P,TO-3PF,TO-247 : 25N TO-3PL : 45N T-Pack,K-Pack : 10N Force maintaining duration :101s Load force TO-220,TO-220F : 5N TO-3P,TO-3PF,TO-247 : 10N TO-3PL : 15N T-Pack,K-Pack : 5N Number of times :2times(90deg./time) Screwing torque value: (M3) TO-220,TO-220F : 4010N TO-3P,TO-3PF,TO-247 : 5010N TO-3PL : 7010N frequency : 100Hz to 2kHz 2 Acceleration : 100m/s Sweeping time : 4min./1 cycle 4times for each X,Y&Z directions. 2 Peak amplitude: 15km/s Duration time : 0.5ms 3times for each X,Y&Z directions. Solder:Sn-37Pb Solder temp.:2302 Immersion time : 3s Lead length:10mm cut apply to flux Solder:Sn-3Ag-0.5Cu Solder temp.: 2453 Immersion time : 3s Lead length:10mm cut apply to flux Solder temp. : 2605C Immersion time : 101s Number of times : 1times n. g i s de 3 Mounting Strength Mechanical test This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. 1 Terminal Strength (Tensile) Reference Sampling Acceptance Standard number number EIAJ ED4701 A-121 5 A-122 test code D 5 A-131A test code A 5 A-132 5 MS5D1753 (0:1) 5 4/12 H04-004-03 Testing methods and Conditions 1 High Temp. Storage 2 Low Temp. Storage 3 Temperature Humidity Storage 4 Temperature Humidity Bias 5 Unsaturated Pressurized Vapor 6 Temperature Cycle 7 Thermal Shock 8 Steady state Operating life 9 Intermittent Operating Life 10 High Temp. Reverse Bias Failure Criteria Temperature :stg max Test duration : 1000h Temperature : Tstg min Test duration : 1000h Temperature : 852C Relative humidity : 855% Test duration : 1000h Temperature : 852C Relative humidity : 855% Bias Voltage : VRRMx 0.8 Test duration : 1000h Temperature : 1202C Relative humidity : 855% Vapor pressure : 170kPa Test duration : 96h High temp.side : Tstg max Room temp. : 535 Low temp.side : Tstg min Duration time : HT 30min,RT 5min LT 30min Number of cycles : 100 cycles Fluid : pure water(running water) High temp.side : 100+0/-5C Low temp.side : 0+5/-0C Duration time : HT 5min,LT 5min Number of cycles : 100 cycles Ta=255C Rated load Test duration : 1000h Tj=Tjmax 50 B-112A 22 B-121A test code C 22 B-122A test code C 22 B-123A test code B 22 B-131A 22 B-141A test code A 22 D-402 22 (0:1) D-403 ew n for . n sig D-404 22 22 nd e mm IR USL x 5 VFUSL x 1.1 t No Reference Sampling Acceptance Standard number number EIAJ ED4701 B-111A 22 de 3min ON, 3min OFF Test duration : 10000cy Temperature : Ta= 100 C Bias Voltage : VR=VRRM duty=1/2 Test duration : 1000h USL:Upper specification Limit o c e r Fuji Electric Co.,Ltd. DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. Endurance test Test Test No. Items MS5D1753 5/12 H04-004-03 6.Cautions Although Fuji Electric is continually improving product quality and reliability, a small percentage of semiconductor products may become faulty. When using Fuji Electric semiconductor products in your equipment, you are requested to take adequate safety measures to prevent the equipment from causing physical injury, fire, or other problem in case any of the products fail. It is recommended to make your design fail-safe, flame retardant, and free of malfunction. The products described in this Specification are not designed or manufactured to be used in equipment or systems used under life-threatening situations. If you are considering using these products in the equipment listed below, first check the system construction and required reliability. Transportation equipment (automobiles, trains, ships, etc.) Backbone network equipment Traffic-signal control equipment Gas alarms, leakage gas auto breakers Submarine repeater equipment Burglar alarms, fire alarms, emergency equipment Medical equipment Nuclear control equipment etc. de . Do not use the products in this Specification for equipment requiring strict reliability such as (but not limited to): Aerospace equipment Aeronautical equipment ew n for 7.Warnings n sig nd e mm The Diodes should be used in products within their absolute maximum rating (voltage, current, temperature, etc. ). The Diodes may be destroyed if used beyond the rating. The equipment containing Diodes should have adequate fuses or protection to prevent the equipment from causing secondary destruction. Use the Diodes within their reliability and lifetime under certain environments or conditions. The Diodes may fail before the target lifetime of your products if used under certain reliability conditions. You must design the Diodes to be operated within the specified maximum ratings (voltage, current, temperature, etc. )to prevent possible failure or destruction of devices. Consider the possible temperature rise not only for the junction and case, but also for the leads. Do not directly touch the leads or package of the Diodes while power is supplied or during operation, to avoid electric shock and burns. t No o c e r Fuji Electric Co.,Ltd. DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. The products described in this Specification are intended for use in the following electronic and electrical equipment which has normal reliability requirements. Computers OA equipment Communications equipment (Terminal devices) Measurement equipment Machine tools AV equipment Electrical home appliances Personal equipment Industrial robots etc. MS5D1753 6/12 H04-004-03 The Diodes are made of incombustible material. However, if a Diode fails, it may emit smoke of flame. Also, operating the Diodes near any flammable place or material may cause the Diodes to emit smoke or flame in case the Diodes become even hotter during operation. Design the arrangement to prevent the spread of fire. The Diodes should not used in an environment in the presence of acid, organic matter, or corrosive gas (hydrogen sulfide, sulfurous acid gas.) The Diodes should not used in an irradiated field since they are not radiation-proof. Installation Soldering involves temperatures which exceed the device storage temperature rating. To avoid device damage and to ensure reliability, observe the following guidelines from the quality assurance standard. Solder temperature and duration (through-hole package) Duration 101second 3.00.5second The immersion depth of the lead should basically be up to the lead stopper and the distance should be a maximum of 1.5mm from the device. When flow-soldering, take care to avoid immersing the package in the solder bath. Refer to the following torque reference When mounting the device on a heat sink. Excess torque applied to the mounting screw causes damage to the device and weak torque will increase the thermal resistance, both of which conditions may destroy the device. de Table 1:Recommended tightening torque Package style Screw Recommended tightening torque TO-220 M3 30-50Ncm TO-220F ew n for . n sig The heat sink should have a flatness within50m and roughness within 10m. Also, keep the tightening torque within the limits of this specification. Improper handling may cause isolation breakdown leading to a critical accident. We recommend the use of thermal compound to optimize the efficiency of heat radiation. It is important to evenly apply the compound and to eliminate any air voids. nd e mm o c e r ot N The Diodes must be stored at a standard temperature of 5 to 35 and relative humidity of 45 Storage to 75%.If the storage area is very dry, a humidifier may be required. In such a case, use only deionized water or boiled water, since the chlorine in tap water may corrode the leads. The Diodes should not be subjected to rapid changes in temperature to avoid condensation on the surface of the Diodes. Therefore, store the Diodes in a place where the temperature is steady. The Diodes should not be stored on top of each other, since this may cause excessive external force on the case. The Diodes should not be stored with the lead terminals remaining unprocessed. Rust may cause presoldered connections to go fail during later processing. The Diodes should be stored in antistatic containers or shipping bags. Fuji Electric Co.,Ltd. DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. Solder temperature 2605 35010 MS5D1753 7/12 H04-004-03 8.Appendix If you have any questions about any part of this Specification, please contact Fuji Electric or its sales agentbefore using the product Neither Fuji nor its agents shall be held liable for any injury caused by using the products not in accordance with the instructions. The application examples described in this specification are merely typical uses of Fuji Electric products. This specification does not confer any industrial property rights or other rights, nor constitute a license for such rights. de ew n for . n sig nd e mm t No o c e r Fuji Electric Co.,Ltd. DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. These products do not contain PBDEs or PBBs. These products, assemblies, or components do not contain any of the above-mentioned substances. Prohibited substances: CFCs, halon, carbon tetrachloride, 1, 1, 1-trichloroethane (methyl chloroform) These products, assemblies, or components are not manufactured using any of the above-mentioned substances. Prohibited substances: CFCs, halon, carbon tetrachloride, 1, 1, 1-trichloroethane (methyl chloroform) MS5D1753 8/12 H04-004-03 No t Fuji Electric Co.,Ltd. DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. de ew n for n sig MS5D1753 . nd e mm o c e r 9/12 H04-004-03 Forward Characteristic (typ.) Reverse Characteristic 100 (typ.) 102 Tj=150 Tj=125 Tj=150 Tj=100 101 Tj=125 Reverse Current 10 1 Tj=100 100 Tj= 25 R Forward Current Tj=25 10-2 0.1 0.0 0 0.5 1.0 100 1.5 Forward Voltage nd e mm 24 t No 18 16 o c e r Dissipation 20 Square wave =60 22 500 600 700 . de 0.028 26 400 n sig Reverse Power Dissipation (max.) 0.030 28 Square wave =120 Sine wave =180 Square wave =180 DC Reverse Power 14 12 10 0.026 0.024 0.022 DC 0.020 0.018 0.016 0.014 0.012 =180 0.010 0.008 8 6 0.006 0.004 4 2 0.002 Per 1element 0.000 0 0 2 4 6 8 10 Average Forward Current 12 14 16 0 Fuji Electric Co.,Ltd. 100 200 DWG.NO. 300 Reverse Voltage ew n for 30 Forward Power Dissipation 200 R Forward Power Dissipation (max.) This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. 10-1 300 400 Reverse Voltage MS5D1753 500 600 700 10/12 H04-004-03 Current Derating Junction Capacitance Characteristic (typ.) (Io-Tc) (max.) 160 150 140 100 DC 120 Square wave =180 Sine wave =180 100 Square wave =120 90 Cj Case Temperature 110 This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. Junction Capacitance (pF) 130 Square wave =60 80 70 60 50 0 5 10 15 Average Output Current 20 10 10 de VR :Conduction angle of forward current for each rectifier element Io:Output current of center-tap full wave connection Surge Capability (max.) 1000 n sig nd e mm t No o c e r 100 FSM Peak Half - Wave Current ew n for . 100 Reverse Voltage (V) 10 10 Number of Cycles at 50Hz Fuji Electric Co.,Ltd. DWG.NO. 1 MS5D1753 11/12 H04-004-03 10-1 10-3 No 10-2 t Fuji Electric Co.,Ltd. 10-1 Time DWG.NO. This material and the information herein is the property of Fuji Electric Co.,Ltd. They shall be neither reproduced, copied, lent, or disclosed in any way whatever for the use of any t h ird pa rt y n o r u s ed f o r th e m an uf a c tu rin g p u rp o se s wit h o u t the express written consent Fuji Electric Co.,Ltd. Transient Thermal Impedance 102 Transient Thermal Impedance (max.) 101 Rth j-c:1.2/W 100 100 101 ew n for 102 de n sig MS5D1753 . nd e mm o c e r 12/12 H04-004-03