FLUKE-190-204/AM CAL D - FLUKE - Datasheet.Directory

ScopeMeter® 190 Series

190 Series II, 190C Series,

and 190C Series with Bus Health

Technical Data

A new generation of

ScopeMeter

The 190 Series II include these new

capabilities:

• 4 independent floating isolated

inputs, up to 1000 V

• High-speed sampling: Up to

2.5 GS/sec

• Deep memory: 10,000 points per

trace waveform capture

• CAT III 1000 V/CAT IV 600 V

rated for safety in high voltage

environments

• Up to 7 hours of battery operation,

standard

• Isolated USB host port for direct

data storage to a USB memory

device; USB device port for easy PC

communication

• Easy access battery door for quick

battery swaps in the field

• Compact and only 2.2 kg (4.8 lb)

• Security slot: lock down oscillo-

scope with Kensington® lock while

unattended

ScopeMeter 190C Series

and 190 Series II

Rugged performance, speed

and ease of use no matter

which model you use

All 190 Series models offer:

• IP 51 rating, dust- and drip-proof

• Connect-and-View™ triggering for

intelligent, automatic triggering on

fast, slow and even complex signals

• Frequency Spectrum using

FFT-analysis

• Automatic capture and REPLAY of

100 screens

• Deep waveform memory storage (up

to 10,000 points per input channel)

• 30,000 points or more per input

channel using ScopeRecord™ roll

mode

• Paperless recorder with deep

memory for long-term automatic

measurements



Models 190-204, 199C,

and 225 C shown here

ScopeMeter Series II 190-104 and 190-204:

The first high-performance four-channel

scopes built for harsh industrial environments

Introducing the first high-performance portable oscilloscopes

with four independent isolated input channels, an IP 51 dust- and

drip-proof rating, and a CAT III 1000 V / CAT IV 600 V safety

rating. Choose 200 MHz or 100 MHz bandwidth models. Now,

plant maintenance engineers and technicians can take a four-

channel scope into the harsh world of industrial electronics.

2 Fluke Corporation ScopeMeter 190 Series II2 Fluke Corporation ScopeMeter 190 Series II

Oscilloscope Modes

190C Series 190 Series II

199C, 225C 196C, 215C 192C 190-204 190-104

Vertical deflection

Number of channels 2 2 2 4 4

Bandwidth 200 MHz 100 MHz 60 MHz 200 MHz 100 MHz

Rise time 1.7 ns 3.5 ns 5.8 ns 1.7 ns 3.5 ns

Number of inputs 2 inputs plus external trigger 4 input channels

Channel architecture All inputs fully insulated from each other and from ground. Inputs may be activated in any combination.

Input coupling AC or DC, with ground level indicator

Input sensitivity 2 mV/div to 100 V/div

Bandwidth limiter User selectable: 20 kHz, 20 MHz or full bandwidth

Normal/invert On each input channel, switched separately

Variable attenuator Variable Gain on input channel A Variable Gain on each input channel

Input voltage CAT II 1000 V, CAT III 600 V rated – see General Specifications for

further details

CAT III 1000 V, CAT IV 600 V rated – see

General Specifications for further details

Vertical resolution 8 bit

Accuracy ± (1.5 % of reading + 0.04 x range/div) @ 5 mV/div to 100 V/div ± (2.1 % of reading + 0.04 x range/div)

@ 5 mV/div to 100 V/div.

Input impedance 1 MΩ ± 1 % // 15 pF ± 2 pF 1 MΩ ± 1 % // 14 pF ± 2 pF

Horizontal

Maximum real-time

sample rate

2.5 GS/s (2 ch) 1 GS/s (2 ch) 500 MS/s (2 ch) 2.5 GS/s (2 ch)

1.25 GS/s (4 ch)

1.25 GS/s for each

channel

Record length Up to 3000 samples per channel Up to 10,000 samples per channel

Time base range 5 ns/div to 5 s/div (in 1-2-5-range).

Slower time/division settings using

ScopeRecord Roll mode.

10 ns/div to 5 s/div 5 ns/div to 4 s/div. in a 1-2-4-sequence.

Slower time/division settings using

ScopeRecord Roll mode.

Maximum record

length

3000 samples per channel (x2) in scope mode 10,000 samples per channel (x4) in scope

mode

27,000 points per input in ScopeRecord™ roll mode

(5 ms/div to 2 min/div)

30,000 points per input in

ScopeRecord™ roll mode

Timing accuracy ± (0.01 % of reading + 1 pixel)

Glitch capture 50 nsec (5 μsec/div to 1 min/div) 8 ns peak detect on each channel

Display and acquisition

Display 144 mm full-color LCD, with backlight 153 mm full-color LCD with LED backlight

Display modes Any combination of channels; average on/off; replay

Visible screen width 12 divisions horizontally in scope mode

Persistence modes Digital persistence off/short/medium/long/infinite; traces fade out in seven levels

Waveform

mathematics

A + B, A – B, A * B, all with user selectable scaling of resultant;

A versus B (X-Y-mode); Frequency Spectrum using FFT analysis

One mathematical operation on 2 input

channels: add/subtract/multiply; all with

scalable resultant; X-Y-mode; Frequency

Spectrum using FFT analysis

Acquisition modes Normal, Averaged, Auto, Single Shot, ScopeRecord™ roll, glitch capture, waveform compare with automatic

“Pass/Fail testing”, Replay

ScopeMeter 190 Series II Fluke Corporation 3

190C Series 190 Series II

199C, 225C 196C, 215C 192C 190-204 190-104

Trigger and delay

Source Any of the input channels. All input references isolated from each other and from ‘earth ground’.

Modes Automatic Connect-and-View™, free run, single shot, edge, delay, dual slope, video, video line, selectable pulsewidth

(channel A only), N-cycle

Connect-and-View™ Advanced automatic triggering that recognizes signal patterns, automatically sets up and continuously adjusts triggering,

time base and amplitude. Automatically displays stable waveforms of complex and dynamic signals like motor drive and

control signals. Can be switched off if preferred.

Video triggering (on

channel A)

NTSC, PAL, PAL+, SECAM. Includes field 1, field 2 and line select.

High-Res, non-inter-

laced video

— Non-interlaced video with line-select, for line

frequencies in the range 14 kHz up to 65 kHz

Pulse width triggering

(on channel A)

Pulse width qualified by time. Allows for triggering <t, >t, =t, ≠ t,

where t is selectable in minimum steps of 0.01 div or 50 ns.

Time delay 1 full screen of pre-trigger view or up to 100 screens (=1200 divisions) of post-trigger delay

Dual slope triggering Triggers on both rising and falling edges alike

N-cycle triggering Triggers on N-th occurrence of a trigger event; N to be set in the range 2 to 99

Automatic capture of 100 screens

When in oscilloscope mode, the instrument ALWAYS memorizes the last 100 screens—no specific user setup required. When an anomaly is seen,

the REPLAY button can be pressed to review the full sequence of screen events over and over. Instrument can be set up for triggering on glitches

or intermittent anomalies and will operate in “baby-sit” mode capturing 100 specified events.

Replay Manual or continuous replay. Displays the captured 100 screens as a “live” animation, or under manual control.

Each screen has date and time-stamp.

Replay storage Up to 2 sets of 100 screens each can be saved for later recall and

analysis.

Two sets of 100 screens each can be saved

internally for later recall and analysis. Direct

storage of additional sets on external flash

memory drive through USB host port.

FFT – frequency spectrum analysis

Shows frequency content of oscilloscope waveform using Fast Fourier Transform

Window Automatic, Hamming, Henning or None

Automatic window Digitally re-samples acquired waveform to get optimum frequency resolution in FFT resultant

Vertical scale Linear / Logarithmic (in volts or amps)

Frequency axis Logarithmic; frequency range automatically set as function of

timebase range of oscilloscope

User selectable: lin or log. Frequency range

automatically set as a function of timebase

range of oscilloscope.

Waveform compare and pass/fail testing

Waveform compare Provides storage and display of a reference waveform for visual comparison with newly acquired waveforms. Reference

is derived from an acquired waveform and can be modified in the ScopeMeter or externally using FlukeView Software.

Pass/Fail Testing In waveform compare mode, the ScopeMeter can be set up to store only matching (“Pass”) or only non-matching (“Fail”)

acquired waveforms in the replay memory bank for further analysis

Automatic scope measurements

Vdc, Vac rms, Vac+dc, Vpeak max, Vpeak min, Vpeak to peak, Aac, Adc, Aac+dc, frequency (in Hz), risetime (using cursors), falltime (using

cursors), Power Factor (PF), Watts, VA, VA reactive, phase (between any 2 inputs), pulsewidth (pos./neg.), dutycycle (pos./neg.), temperature

°C, temperature °F, dBV, dBm into 50 Ω and 600 Ω, VPWM ac and VPWM ac+dc for measurement on pulsewidth modulated motordrives and

frequency inverters

Advanced functions — mA*s (current-over-time, between cursors)

V*s (voltage over time, between cursors) W*s

(energy, between cursors)

Cursor measurements

Source On any input waveform or on mathematical resultant waveform (excl. X-Y-mode)

Dual horizontal lines Voltage at cursor 1 and at cursor 2, voltage between cursors

Dual vertical lines Time between cursors, 1/T between cursors (in Hz), voltage between markers, risetime with markers,

falltime with markers; Vrms between cursors, Watts between cursors

Single vertical line Min-Max and Average voltage at cursor position; frequency and rms-value of individual frequency component in the FFT

Result

ZOOM Up to 16x horizontal zoom Ranges from full record overview to zoom in up

to sample level, at any record length

4 Fluke Corporation ScopeMeter 190 Series II

Bus Health Test Mode (225C and 215C models only)

Bus Health automatically analyzes the electrical signals on the industrial bus system to measure individual parameters and to give waveform

information. Automatically compares the measurement results to preset values and present ‘good,‘weak’ or ’false’ indicator with each parameter.

Bus types and reference standards used • AS-i (EN50295, 166 kb/s);

• CAN-bus (ISO-11898, up to 1 Mb/s);

• Modbus (EIA-232 up to 115 kb/s and EIA-485 up to 10 Mb/s);

• Foundation Fieldbus H1 (61158 type 1, 31.25 kb/s) ;

• Profibus DP (EIA-485 up to 10 Mb/s) and PA (61158 type 1 31.25 kb/s);

• Ethernet [10Base2 (coaxial) and 10BaseT (UTP)], 10 Mb/s;

• Ethernet 100BaseT (100 Mb/s);

• RS-232 (EIA-232, up to 115 kb/s);

• RS-485 (EIA-485, up to 10 Mb/s).

Measured parameters (where applicable) Bias voltage level, signal amplitude, pulse width or baud rate, risetime, fall time, jitter, signal

distortion, noise HF, noise LF, in-band noise

Meter Mode

190C Series 190 Series II

199C, 196C, 192C, 215C, 225C, 190-204, 190-104

Meter inputs Via 4 mm banana inputs, fully isolated from

scope inputs and scope ground

Up to four automatic meter measurements

can be made at the same time, using the

oscilloscope input channels

The speciﬁed accuracy is valid over the temperature range 18 °C to 28 °C (65 °F to 82 °F).

Add 10 % of speciﬁed accuracy for each degree C below 18 °C or above 28 °C.

Maximum resolution 5,000 counts 999 counts

Meter input impedance 1 MΩ ± 1 % // 10 pF ± 2 pF (thru scope channel:)

1 MΩ ± 1 % // 14 pF ± 2 pF

Advanced meter functions Auto/manual ranging, relative measurements (Zero reference), TrendPlot recording

Vdc, Vac, Vac+dc

Vdc accuracy ± (0.5 % + 5 counts) ± (1.5 % + 5 counts)

Vac true rms accuracy

15 Hz to 60 Hz: ± (1 % + 10 counts) ± (1.5 % + 10 counts)

60 Hz to 1 kHz: ± (2.5 % + 15 counts)

60 Hz to 20 kHz: — ± (2.5 % + 15 counts)

Vac+dc true rms accuracy

15 Hz to 60 Hz: ± (1 % + 10 counts) ± (1.5 % + 10 counts)

60 Hz to 1 kHz: ± (2.5 % + 15 counts)

60 Hz to 20 kHz: — ± (2.5 % + 15 counts)

Voltmeter ranges 500 mV, 5 V, 50 V, 500 V, 1,000 V

Ohms

Ranges 500 Ω, 5 kΩ, 50 kΩ, 500 kΩ, 5 MΩ, 30 MΩ —

Accuracy ± (0.6 % + 5 counts) —

Other meter functions

Continuity Beeper on < 50 Ω (± 30 Ω) —

Diode test Up to 2.8 V —

Amps Adc, Aac, Aac + dc using an optional current clamp or shunt.

Scaling factors: 0.1 mV/A, 1 mV/A, to 100 V/A and 400 mV/A

Temperature With optional accessories. Scale factors 1 °C/mV or 1 °F/mV

ScopeMeter 190 Series II Fluke Corporation 5

Recorder Modes

190C Series 190 Series II

199C, 196C, 192C, 215C, 225C, 190-204, 190-104

ScopeRecord™ Roll Mode

Dual or multiple input waveform storage mode, using deep memory

Source and display Input A, Input B, Dual Any combination of inputs, up to 4 channels.

All channels sampled simultaneously.

Bandwidth 20 MHz or 20 kHz, user selectable

Memory depth 27,000 or more data points, each holding min/max. pair of information

Min/max values Min/max values are measured at high sample rate ensuring capture and display of glitches

Recording modes Single sweep, continuous roll,

Start-on-Trigger (through external),

Stop-on-Trigger (through external)

Single sweep, continuous roll,

Start-on-Trigger (through any channel)

Stop-on-Trigger (through any channel)

Stop-on-trigger ScopeRecord mode can be stopped by an individual trigger event, or by an interruption of a

repetitive trigger signal, through any input channel (through External on 190C Series)

Horizontal scale Time from start, time of day

Zoom Ranges from full record overview to zoom in up to sample level, at any record length

Memory Up to 2 dual input ScopeRecord waveforms can

be saved for later recall and analysis.

Two multiple input ScopeRecord waveforms

can be saved internally for later recall and

analysis. Direct storage on external ﬂash

memory drive through USB host port.

ScopeRecord sample rate and recording timespan

Time base range 5 ms/div ~ 2 min/div

Recorded timespan 6 sec ~ 48 hr

Time/division in ‘view all’ mode 0.5 s/div. ~ 4 h/div

Glitch capture 8 ns

Sample rate 125 MS/s

Resolution 200 μsec ~ 4.8 sec

Trendplot™ Recording

Single or dual input electronic paperless chart

recorder. Plots, displays and stores meter and

scope measurements.

Multiple channel electronic paperless

recorder. Graphically plots, displays and

stores results of up to 4 automatic scope

measurement over time.

Source and display Any combination of measurements, made on any of the input channels

Memory depth 18,000 points record per input. Each recorded sample point contains a minimum, a maximum

and an average value, plus a date- and timestamp.

Ranges Normal view: 5 s/div to 30 min/div

In view-all mode: 5 min/div to 48 hr/div (overview of total record)

Recorded time span Up to 22 days with a resolution of 1 minute More than 22 days, with a resolution of

102 seconds

Recording mode Continuous roll for the duration of the full

recordable timespan

Continuous recording, starting at 5 s/div. with

automatic record compression

Measurement speed 5 automatic measurements per second or more

Horizontal scale Time from start, time of day

Zoom Up to 64x zoom Up to 64x zoom-out for full record overview,

up to 10x zoom-in for maximum detail.

Memory Up to 2 TrendPlot recordings can be saved for

later recall and analysis.

Two multiple input TrendPlot records can be

saved internally for later recall and analysis.

Direct storage on external ﬂash memory drive

through USB host port.

Cursor measurements – all recorder modes

Source Any waveform trace in any waveform display mode (Scope, ScopeRecord or TrendPlot)

Dual vertical lines Cursors may be used to identify Min, Max or Average value of any datapoint in a record, with

time between cursors, time from start or absolute time.

5 ms/div to 1 min/div 2 min/div

6 sec to 24 hr 48 hr

50 ns 250 ns

20 MS/s 4 MS/s

200 μsec to 2 sec 4.8 sec

6 Fluke Corporation ScopeMeter 190 Series II

General Specifications

190C Series 190 Series II

199C, 196C, 192C, 215C, 225C, 190-204, 190-104

Input voltage ratings

Rated input voltage and max. ﬂoating voltage CAT II 1000 V, CAT III 600 V CAT III 1000 V, CAT IV 600 V

Maximum voltage between any contact and earth-ground voltage level

Maximum probe voltage CAT II 1000 V, CAT III 600 V CAT III 1000 V, CAT IV 600 V

Maximum voltage between standard 10:1 probe tip and reference lead

Maximum BNC input voltage 300 V CAT IV

Maximum voltage on BNC input directly

Maximum voltage on meter input CAT II 1000 V, CAT III 600 V —

Safety designed banana input connectors

Memory save and recall

Memory locations 15 waveform memories plus 2 recording memories

15 waveform memory locations Stores Scope-trace waveform data (2 traces

each) plus screen-copy plus corresponding

setup

Stores Scope-trace waveform data (4 traces

each) plus screen-copy plus corresponding

setup

2 recording memories Each may contain:

• a 100 Screen Replay sequence, or

• a ScopeRecord Roll-mode recording (2

traces), or

• a TrendPlot recording of 2 measurements

Each may contain:

• a 100 Screen Replay sequence, or

• a ScopeRecord Roll-mode recording (4

traces), or

• a TrendPlot recording of 4 measurements

External data storage • On PC, using FlukeView™ Software • On PC, using FlukeView™ Software, or

• Direct storage on external flash memory

drive through USB host port

Screencopies • On PC, using FlukeView Software • On PC, using FlukeView™ Software, or

• Internally (in instrument) which can be

copied on to external flash memory drive as

.BMP-file, through USB host port

Volatility Data is stored in RAM which is maintained by

the instrument’s main battery

Measurement data is initially stored in RAM,

which is maintained by the main battery

with a 30 seconds back-up when battery is

exchanged. When storing data, this is written

in non-volatile flash-ROM.

Real-time clock Provides date and time stamp information for ScopeRecord, for 100 Screen Replay sequences

and for TrendPlot recordings

Case

Design Rugged, shock-proof with integrated protective holster.

Handstrap and hangstrap included as standard.

Drip and dust proof IP 51 according to IEC529

Shock and vibration Shock 30 g, vibration (sinusoidal) 3 g according to MIL-PRF-28800F Class 2

Display size 115.2 mm x 86.4 mm (4.54 in x 3.4 in);

144 mm (5.67 in) diagonal LCD

127 mm x 88 mm (153 mm diagonal) LCD

Resolution 320 x 240 pixels

Contrast and brightness User adjustable, temperature compensated

Brightness 80 cd/m2 typ. using power adapter 200 cd/m2 typ. using power adapter,

90 cd/m2 typ. using battery power

Mechanical data

Size 256 mm x 169 mm x 64 mm

(10.1 in x 6.6 in x 2.5 in)

265 mm x 190 mm x 70 mm

(10.5 in x 7.5 in x 2.8 in)

Weight (incl. battery) 2 kg (4.4 lb) 2.2 kg (4.8 lb)

Power

Line power Mains adapter/battery charger BC190 included, version depending of country

Battery power Rechargeable NiMH BP190 (installed) Rechargeable double capacity Li-ion battery

BP291 (included). Battery swappable through

easily accessible battery door at the rear of

the instrument.

Battery charge indicator Battery status indicator on instrument screen Battery has built-in status indicator for use

with external charger, next to battery status

indicator on instrument screen

ScopeMeter 190 Series II Fluke Corporation 7

FlukeView® ScopeMeter® Software

System requirements

• Microsoft® Windows® XP and beyond

• CD-ROM drive

• One free USB port

Supported Instruments

With the new release V5, the following typenumbers

are supported:

• Fluke 190C-series (225C, 215C, 199C, 196C, 192C,

using an OC4USB or PM9080 interface cable);

• Fluke 190B-series (199B, 196B, 192B, using an

OC4USB or PM9080 interface cable);

• 190-series II (190-204 and 190-104, using

USB-cable);

• 120-series (123, 124, 125, using an OC4USB or

PM9080 interface cable).

FlukeView ScopeMeter software helps you

get more out of your ScopeMeter:

• Store instrument’s screen copies on the PC, in color

• Copy screen images into your reports and

documentation

• Capture and store waveform data from your

ScopeMeter on your PC

• Create and archive waveform references for

automatic or visual comparison

• Includes waveform analysis, e.g. FFT spectrum

analysis

• Copy waveform data into your spreadsheet for

detailed analysis

• Use cursors for parameter measurement

190C Series 190 Series II

199C, 196C, 192C, 215C, 225C, 190-204, 190-104

Battery operating time (with backlight low) > 3½ hours Up to 7 hours using BP291 (included)

Battery charging time 4 hours 5 hours

Battery power saving functions Auto ‘power down’ with adjustable

power down time.

On-screen battery power indicator.

Auto ‘power down’ with adjustable

power down time; Auto ‘Display off’ with

adjustable power down time; On-screen

battery power indicator.

Safety

Compliance EN61010-1-2001, Pollution Degree 2;

UL61010B, with approval;

CAN/CSA C22.2, No. 61010-1-04, with

approval; ANSI/ISA-82.02.01

EN61010-1-2001, Pollution Degree 2;

CAN/CSA C22.2, No. 61010-1-04, with

approval; UL61010B; ANSI/ISA-82.02.01

Environmental

Operating temperature 0 °C ~ +50 °C 0 °C ~ +40 °C incl. battery

+40 °C ~ +50 °C excl. battery

Storage temperature -20 °C ~ +60 °C

Humidity +10 °C ~ +30 °C: 95 % RH non-condensing

+30 °C ~ +40 °C: 75% RH non-condensing

+40 °C ~ +50 °C: 45% RH non-condensing

Maximum operating altitude 3,000 m (10,000 feet) Up to 2,000 m (6666 ft) for CAT IV 600 V,

CAT III 1000 V; up to 3,000 m (10,000 ft) for

CAT III 600 V, CAT II 1000 V

Maximum storage altitude 12 km (40,000 ft)

Electro-Magnetic-Compatibility (EMC) EN 61326-1 for emission and immunity EN 61326-1 (2005-12) for emission and

immunity

Interface Optical port in instrument transfers

instrument settings, screen images and

waveform data, compatible with FlukeView®

software for Windows®, via optional OC4USB

or PM9080 (optical to electrical interface

cable)

Two USB ports provided. Ports are fully

insulated from instrument’s ﬂoating

measurement circuitry. USB-host port directly

connects to external ﬂash memory drive

for storage of waveform data, measurement

results, instrument settings and screen

copies. A mini-USB-B is provided which

allows for interconnection to PC for remote

control and data transfer under PC-control.

Warranty Three-years (parts and labor) on main instrument, one-year on accessories

Probe calibration output (through DMM-input banana connectors) Dedicated probe-cal output with reference

contact provided, fully insulated from any

measurement input channel

8 Fluke Corporation ScopeMeter 190 Series II

Accessories

190C Series 190 Series II

199C, 196C, 192C, 215C, 225C, 190-204, 190-104

Standard accessories

BC190 Mains adapter/battery charger for any 190-series instrument

Battery (type) BP190 NiMH battery BP291 Li-ion battery

Voltage

probes and

test leads

VPS210

TL75

Probe sets, 10:1 (1 red, 1 grey) including hook-

clips, ground leads with mini-alligator clips,

ground springs and probe-tip insulation sleeves

Test lead set (1 red, 1 black)

VPS410 Probe-sets, 10:1 (1 red, 1 blue, 1 grey, 1 green)

including hookclips, ground leads with mini-

alligator clips, ground springs and probe-tip

insulation sleeves

Other BHT190 Bus Health Test Connection Set (included with

Fluke 225C and 215C models only)

FlukeView demo package (with restricted functionality);

USB interface cable for PC connectivity

Handstrap (afﬁxed to instrument) and hangstrap Users manual on CD-ROM

Optional accessories

SW90W FlukeView ScopeMeter software package

(full version)

SW90W FlukeView ScopeMeter software package

(full version)

C190 Hard Shell Carrying Case for 190C Series C290 Hard Shell Carrying Case for 190 Series II

SCC190 FlukeView Software, OC4USB-cable and C190

Carrying Case Kit

SCC290 Software and Carrying Case kit; includes

FlukeView Software and C290 Carrying Case

BP190 Rechargeable NiMH Battery Pack for Fluke

190C Series

BP291 Double capacity Li-ion Battery (4800 mAh) for

Fluke 190 Series II

VPS210 Voltage probe set, 10:1. Red and grey sets

available

VPS410-x Voltage probe set 10:1. Available colors: VPS410-

R (red), VPS410-B (blue), VPS410-G (grey) and

VPS410-V (green)

OC4USB Optically isolated interface cable for USB VPS420-R High Working Voltage Ruggedized Probe,

100:1, red/black

PM9080 Optically isolated interface cable for RS-232 EBC290 External Battery Charger, charges BP291 while

outside instrument

AS200 Probe accessory extension set for VPS210 Series

probes

HH290 Hanging Hook

RS200 Probe accessory replacement set for VPS210

Series probes

AS400 Probe accessories extension set for VPS410

Series probes

RS400 Probe accessories replacement set for VPS410

Series probes

Fluke also offers a wide range of optional accessories like temperature probes, current clamps, high voltage probes, cables, adapters and carrying cases to further assist

you in your job. See the Fluke website or contact your distributor for details.

Ordering Information

190-204 Color ScopeMeter (200 MHz, 4 channel)

190-204/S Color ScopeMeter (200 MHz, 4 channel), with SCC290-kit

190-104 Color ScopeMeter (100 MHz, 4 channel)

190-104/S Color ScopeMeter (100 MHz, 4 channel), with SCC290-kit

225C Color ScopeMeter (200 MHz/2.5 GS/s) with Bus Health Test Functions

225C/S Color ScopeMeter (200 MHz/2.5 GS/s) with Bus Health Test + SCC190

215C Color ScopeMeter (100 MHz/1 GS/s) with Bus Health Test Functions

215C/S Color ScopeMeter (100 MHz/1 GS/s) with Bus Health Test + SCC190 kit

199C Color ScopeMeter (200 MHz/2.5 GS/s)

199C/S Color ScopeMeter (200 MHz/2.5 GS/s) + SCC190

196C Color ScopeMeter (100 MHz/1 GS/s)

196C/S Color ScopeMeter (100 MHz/1GS/s) + SCC190

192C Color ScopeMeter (60 MHz/500 MS/s)

192C/S Color ScopeMeter (60 MHz/500 MS/s) + SCC190 kit

Fluke Corporation

PO Box 9090, Everett, WA 98206 U.S.A.

Fluke Europe B.V.

PO Box 1186, 5602 BD

Eindhoven, The Netherlands

For more information call:

In the U.S.A. (800) 443-5853 or

Fax (425) 446-5116

In Europe/M-East/Africa +31 (0) 40 2675 200 or

Fax +31 (0) 40 2675 222

In Canada (800)-36-FLUKE or

Fax (905) 890-6866

From other countries +1 (425) 446-5500 or

Fax +1 (425) 446-5116

Web access: http://www.fluke.com

Specifications subject to change without notice.

Printed in U.S.A. 10/2010 3801685A A-EN-N

Modification of this document is not permitted

without written permission from Fluke Corporation.

Fluke. Keeping your world

up and running.®