Instruction Sheet
408-8676
E
2005 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
AMP and Tyco are trademarks. *Trademark
Other products, logos, and company names used are the property of their respective owners. LOC B
1
of 2
TOOLING ASSISTANCE CENTER 1-800-722-1111
FAX/PRODUCT INFO 1-800-522-6752
For Regional Customer Service, visit our website at
www.tycoelectronics.com
This controlled document is subject to change.
For latest revision, call the FAX/PRODUCT INFO number.
17 JAN 05 Rev D
Production Torque Wrenches
PROPER USE GUIDELINES
CumulativeTraumaDisorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume
applications. A wide selection of powered application equipment for extended-use, production operations may be available.
Protective
Cover
Torque
Wrench
Open-End
Wrench Head
177 mm [7.0 In.]
TYCO
ELECTRONICS
PREVIOUS
WRENCH DESCRIPTION
WRENCH SIZE PRESET
ELECTRONICS
PART NUMBER PART NUMBER
WRENCH DESCRIPTION
mm INCHES TORQUE
1055276-1 2098-0351-54 Production Torque Wrench 6.4 [1/4] 18 in.-lbs.
1055419-1 2098-5065-54 For SMA (OSM) Type Connectors 7.9 [5/16] 8 in.-lbs.
1055480-1 2098-5304-54 For OSSM Type Connectors 6.4 [1/4] 5 in.-lbs.
1055512-1 2098-5619-54 For SMA (OSM) Hermetic Type Connectors 7.1 [9/32] 30 in.-lbs.
1055546-1 2098-5830-54 Production Torque Wrench Kit 6.4 and 8.0 [1/4] and [5/16] 8 in.-lbs.
1055790-1 2598-5026-54 For SC / N Type Connectors (Hex Nut Design) 20.6 [13/16] 14 in.-lbs.
1055791-1 2598-5027-54 For TNC Type Connectors (Hex Nut Design) 15.9 [5/8] 14 in.-lbs.
1055826-1 2598-5160-54 Production Torque Wrench 4.0 [5/32] 8 in.-lbs.
1055868-1 2598-5298-54 For TNC Type Connectors (Hex Nut Design) 14.3 [9/16] 14 in.-lbs.
1061789-1 7098-5031-54 For 7 mm Type Connectors 19.1 [3/4] 14 in.-lbs.
1490262-1 2598-5383-50 Production Torque Wrench 7.9 [5/16] 15 in.-lbs.
Figure 1
1. INTRODUCTION
These production torque wrenches are used to
properly install or disassemble the connectors listed in
Figure 1.
Figure 1 also contains the Tyco Electronics part
numbers for the wrenches, the previous part numbers
for the wrenches, wrench size, and the preset torque
for each wrench.
Dimensions on this sheet are in metric units
[with U.S. customary units in brackets], unless
otherwise noted.
Reason for revision is provided in Section 5,
REVISION SUMMARY.
2. DESCRIPTION
Each production torque wrench contains a protective
cover, a torque wrench, and an interchangeable head.
NOTE
408-8676
Production Torque Wrenches
Rev
D2
of 2
Refer to Figure 2 for the appropriate replacement
wrench head part numbers.
The wrenches are designed to be used in the
clockwise or counterclockwise direction.
3. OPERATION OF THE WRENCHES
If a wrench has not been used recently, move the
wrench head back and forth several times,
listening for audible clicks." Clicking the wrench
head back and forth spreads lubricant throughout
the internal mechanism to improve wrench
performance.
TYCO
ELECTRONICS
WRENCH SIZE
ELECTRONICS
PART NUMBER mm INCHES
1406504-1 6.4 [1/4]
1406504-2 8.0 [5/16]
1406504-3 9.6 [3/8]
1406504-4 12.8 [1/2]
1406504-5 19.6 [3/4]
1406504-6 11.2 [7/16]
1406504-7 7.1 [9/32]
1406504-8 10.4 [13/32]
1406504-9 17.6 [11/16]
1-1406504-0 14.6 [9/16]
1-1406504-1 8.8 [11/32]
1-1406504-2 16.0 [5/8]
1-1406504-3 20.8 [13/16]
1-1406504-4 4.0 [5/32]
1-1406504-5 6.1 [15/64]
Figure 2
Using the appropriate sized head (Figure 1), turn the
wrench clockwise (or counterclockwise) until there is
an audible “click.” This “click” indicates that the proper
torque has been achieved.
Do NOT overtighten the connector with the
torque wrench. Over-tightening the wrench could
result in inaccurate torque settings.
Do not use or re-terminate damaged connectors.
4. REPLACEMENT
Remove the wrench head by pulling it off the
production torque wrench. Then replace the head with
the appropriate head listed in Figure 2.
Order replacement parts through your Tyco
Electronics Representative, or call 1–800–526–5142,
or send a facsimile of your purchase order to
717–986–7605, or write to:
CUSTOMER SER VICE (38–35)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105–3608
5. REVISION SUMMARY
Per EC 0990–0037–05:
S
Updated document to corporate requirements
S
Added part number 1490262–1 and related
information to Figure 1
NOTE
CAUTION
CAUTION
