SP1507ABSTM - ST-Ericsson - Datasheet.Directory

1. General description

The ISP1507 is a Universal Serial Bus (USB) On-The-Go (OTG) transceiver that is fully

compliant with Universal Serial Bus Specification Rev. 2.0, On-The-Go Supplement to the

USB 2.0 Specification Rev. 1.3 and UTMI+ Low Pin Interface (ULPI) Specification

Rev. 1.1.

The ISP1507 can transmit and receive USB data at high-speed (480 Mbit/s), full-speed

(12 Mbit/s) and low-speed (1.5 Mbit/s), and provides a pin-optimized, physical layer

front-end attachment to USB host, peripheral and OTG devices.

It is ideal for use in portable electronic devices, such as mobile phones, digital still

cameras, digital video cameras, Personal Digital Assistants (PDAs) and digital audio

players. It allows USB Application-Specific Integrated Circuits (ASICs), Programmable

Logic Devices (PLDs) and any system chip set to interface with the physical layer of the

USB through a 12-pin interface.

The ISP1507 can interface to the link with digital I/O voltages in the range of 1.65 V to

3.6 V.

The ISP1507 is available in HVQFN32 package.

2. Features

Fully complies with:

Universal Serial Bus Specification Rev. 2.0

On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3

UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1

Interfaces to host, peripheral and OTG device cores; optimized for portable devices or

system ASICs with built-in USB OTG device core

Complete Hi-Speed USB physical front-end solution that supports high-speed

(480 Mbit/s), full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s)

Integrated 45 Ω±10 % high-speed termination resistors, 1.5 kΩ±5 % full-speed

device pull-up resistor, and 15 kΩ±5 % host termination resistors

Integrated parallel-to-serial and serial-to-parallel converters to transmit and receive

USB clock and data recovery to receive USB data up to ±500 ppm

Insertion of stuff bits during transmit and discarding of stuff bits during receive

Non-Return-to-Zero Inverted (NRZI) encoding and decoding

Supports bus reset, suspend, resume and high-speed detection handshake (chirp)

Complete USB OTG physical front-end that supports Host Negotiation Protocol (HNP)

and Session Request Protocol (SRP)

ISP1507A; ISP1507B

ULPI Hi-Speed USB On-The-Go transceiver

Rev. 03 — 22 October 2009 Product data sheet

Product data sheet Rev. 03 — 22 October 2009 2 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Integrated 5 V charge pump; also supports external charge pump or 5 V VBUS

switch

Complete control over bus resistors

Data line and VBUS pulsing session request methods

Integrated VBUS voltage comparators

Integrated cable (ID) detector

Highly optimized ULPI-compliant

60 MHz, 12-bit interface between the core and the transceiver

Supports 60 MHz output clock configuration

Integrated Phase-Locked Loop (PLL) supporting one crystal or clock frequency:

19.2 MHz (ISP1507A) and 26 MHz (ISP1507B)

Fully programmable ULPI-compliant register set

Internal Power-On Reset (POR) circuit

Flexible system integration and very low current consumption, optimized for portable

devices

Power-supply input range is 3.0 V to 3.6 V

Internal voltage regulator supplies 3.3 V and 1.8 V

Charge pump regulator outputs 4.65 V to 5.25 V at a current of up to 50 mA,

tunable using an external capacitor

Supports external VBUS charge pump or 5 V VBUS switch:

External VBUS source is controlled using the PSW_N pin; open-drain PSW_N

allows per-port or ganged power control

Digital FAULT input to monitor the external VBUS supply status

Pin CHIP_SELECT_N 3-states the ULPI interface, allowing bus reuse for other

applications

Supports wide range interfacing I/O voltage of 1.65 V to 3.6 V; separate I/O voltage

pins minimize crosstalk

Typical operating current of 11 mA to 48 mA, depending on the USB speed and

bus utilization; not including the charge pump

Typical suspend current of 35 μA

Full industrial grade operating temperature range from −40 °C to +85 °C

4 kV ElectroStatic Discharge (ESD) protection at pins DP, DM, ID, VBUS and GND

Available in a small HVQFN32 (5 mm ×5 mm) Restriction of Hazardous Substances

(RoHS) compliant, halogen-free and lead-free package

3. Applications

Digital still camera

Digital TV

Digital Video Disc (DVD) recorder

External storage device, for example:

Magneto-Optical (MO) drive

Optical drive: CD-ROM, CD-RW, DVD

Zip drive

Mobile phone

MP3 player

Product data sheet Rev. 03 — 22 October 2009 3 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

PDA

Printer

Scanner

Set-Top Box (STB)

Video camera

4. Ordering information

[1] The package marking is the first line of text on the IC package and can be used for IC identification.

Table 1. Ordering information

Commercial

product code

Marking Crystal or clock

frequency

Package description Packing Minimum sellable

quantity

ISP1507ABSTM 507A[1] 19.2 MHz HVQFN32; 32 terminals;

body 5 ×5×0.85 mm

13 inch tape and reel

non-dry pack

6000 pieces

ISP1507BBSTM 507B[1] 26 MHz HVQFN32; 32 terminals;

body 5 ×5×0.85 mm

13 inch tape and reel

non-dry pack

6000 pieces

Product data sheet Rev. 03 — 22 October 2009 4 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

5. Block diagram

Fig 1. Block diagram

MAP

ULPI

INTERFACE

CONTROLLER

USB DATA

SERIALIZER

USB DATA

DESERIALIZER

HI-SPEED USB ATX

STP

DIR

NXT

DATA

[7:0]

1, 23 to 26,

28, 31, 32

004aab035

CLOCK 27

TERMINATION

RESISTORS

DETECTOR

VBUS

COMPARATORS

ON-THE-GO MODULE

SRP CHARGE

AND DISCHARGE

RESISTORS

5 V CHARGE

PUMP SUPPLY

POWER-ON

RESET

PLL

CRYSTAL

OSCILLATOR

VOLTAGE

REGULATOR

BAND GAP

REFERENCE

VOLTAGE RREF

internal power

VCC 11

REG3V3

REG1V8

RESET_N

GLOBAL

RESET

GLOBAL

CLOCKS

XTAL2

XTAL1 15

VCC(I/O) 2, 22, 30 interface voltage

PSW_N

DRV VBUS

EXTERNAL

DRV VBUS

VBUS

FAULT

CPGND

10 C_A

C_B

ISP1507

ULPI

INTERFACE

USB

CABLE

VREF

CHIP_SELECT_N 29

VBUS VALID

EXTERNAL

Product data sheet Rev. 03 — 22 October 2009 5 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

6. Pinning information

6.1 Pinning

6.2 Pin description

Fig 2. Pin configuration HVQFN32; top view

004aab036

ISP1507

Transparent top view

RESET_N

CPGND

REG1V8

FAULT DIR

DP STP

DM NXT

RREF VCC(I/O)

VCC(I/O) DATA7

DATA0 DATA6

C_B

C_A

VCC

PSW_N

VBUS

REG3V3

XTAL1

XTAL2

DATA1

DATA2

VCC(I/O)

CHIP_SELECT_N

DATA3

CLOCK

DATA4

DATA5

8 17

7 18

6 19

5 20

4 21

3 22

2 23

1 24

terminal 1

index area

Table 2. Pin description

Symbol[1][2] Pin Type[3] Description[4]

DATA0 1 I/O pin 0 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

VCC(I/O) 2 P I/O supply rail

RREF 3 AI/O resistor reference

DM 4 AI/O data minus (D−) pin of the USB cable

DP 5 AI/O data plus (D+) pin of the USB cable

FAULT 6 I input pin for the external VBUS digital overcurrent or fault

detector signal

If this pin is not in use, connect it to GND.

plain input; 5 V tolerant

ID 7 I identification (ID) pin of the micro-USB cable

If this pin is not used, it is recommended to connect to

REG3V3.

plain input; TTL level

CPGND 8 P charge pump ground

C_B 9 AI/O flying capacitor pin connection for the charge pump

If this pin is not in use, it must be left floating.

Product data sheet Rev. 03 — 22 October 2009 6 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

C_A 10 AI/O flying capacitor pin connection for the charge pump

If this pin is not in use, it must be left floating.

VCC 11 P input supply voltage or battery source

PSW_N 12 OD active LOW external VBUS power switch or external charge

pump enable

open-drain; 5 V tolerant

VBUS 13 AI/O VBUS pin of the USB cable

5V tolerant

REG3V3 14 P 3.3 V regulator output; requires parallel 0.1 μF and 4.7 μF

capacitors; internally powers ATX and other analog

circuits; must not be used to power external circuits

XTAL1 15 AI crystal oscillator or clock input

XTAL2 16 AO crystal oscillator output

RESET_N 17 I active LOW, asynchronous reset input

plain input

REG1V8 18 P 1.8 V regulator output; requires parallel 0.1 μF and 4.7 μF

capacitors; internally powers the digital core; must not be

used to power external circuits

DIR 19 O ULPI direction signal

slew-rate controlled output (1 ns)

STP 20 I ULPI stop signal

plain input; programmable pull up

NXT 21 O ULPI next signal

slew-rate controlled output (1 ns)

VCC(I/O) 22 P I/O supply rail

DATA7 23 I/O pin 7 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

DATA6 24 I/O pin 6 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

DATA5 25 I/O pin 5 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

DATA4 26 I/O pin 4 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

CLOCK 27 O 60 MHz clock output

slew-rate controlled output (1 ns); plain input

DATA3 28 I/O pin 3 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

Table 2. Pin description …continued

Symbol[1][2] Pin Type[3] Description[4]

Product data sheet Rev. 03 — 22 October 2009 7 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

[1] Symbol names ending with underscore N, for example, NAME_N, indicate active LOW signals.

[2] For details on external components required on each pin, see bill of materials and application diagrams in

Section 16.

[3] I = input; O = output; I/O = digital input/output; OD = open-drain output; AI = analog input; AO = analog

output; AI/O = analog input/output; P = power or ground pin.

[4] A detailed description of these pins can be found in Section 7.9.

CHIP_SELECT_N 29 I active LOW chip select

If this pin is not in use, connect it to GND.

plain input

VCC(I/O) 30 P I/O supply rail

DATA2 31 I/O pin 2 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

DATA1 32 I/O pin 1 of the bidirectional ULPI data bus

slew-rate controlled output (1 ns); plain input;

programmable pull down

GND die pad P ground supply; down bonded to the exposed die pad (heat

sink); to be connected to the PCB ground

Table 2. Pin description …continued

Symbol[1][2] Pin Type[3] Description[4]

Product data sheet Rev. 03 — 22 October 2009 8 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

7. Functional description

7.1 ULPI interface controller

The ISP1507 provides a 12-pin interface that is compliant with UTMI+ Low Pin Interface

(ULPI) Specification Rev. 1.1. This interface must be connected to the USB link.

The ULPI interface controller provides the following functions:

•ULPI-compliant and register set

•Allows full control over the USB peripheral, host and OTG functionality

•Parses USB transmit and receive data

•Prioritizes USB receive data, USB transmit data, interrupts and register operations

•Low-power mode

•Control of the VBUS charge pump or external source

•VBUS monitoring, charging and discharging

•6-pin serial mode and 3-pin serial mode

•Generates RXCMDs; status updates

•Maskable interrupts

•Control over the ULPI bus state, allowing pins to 3-state or attach active weak

pull-down resistors

For more information on the ULPI protocol, see Section 9.

7.2 USB data serializer and deserializer

The USB data serializer prepares data to transmit on the USB bus. To transmit data, the

USB link sends a transmit command and data on the ULPI bus. The serializer performs

parallel-to-serial conversion, bit stuffing and NRZI encoding. For packets with a PID, the

serializer adds a SYNC pattern to the start of the packet, and an EOP pattern to the end of

the packet. When the serializer is busy and cannot accept any more data, the ULPI

interface controller deasserts NXT.

The USB data deserializer decodes data received from the USB bus. When data is

received, the deserializer strips the SYNC and EOP patterns, and then performs

serial-to-parallel conversion, NRZI decoding and discarding of stuff bits on the data

payload. The ULPI interface controller sends data to the USB link by asserting DIR, and

then asserting NXT whenever a byte is ready. The deserializer also detects various

receive errors, including bit stuff errors, elasticity buffer underrun or overrun, and

byte-alignment errors.

7.3 Hi-Speed USB (USB 2.0) ATX

The Hi-Speed USB ATX block is an analog front-end containing the circuitry needed to

transmit, receive and terminate the USB bus in high-speed, full-speed and low-speed, for

USB peripheral, host and OTG implementations. The following circuitry is included:

•Differential drivers to transmit data at high-speed, full-speed and low-speed

Product data sheet Rev. 03 — 22 October 2009 9 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

•Differential and single-ended receivers to receive data at high-speed, full-speed and

low-speed

•Squelch circuit to detect high-speed bus activity

•High-speed disconnect detector

•45 Ω high-speed bus terminations on DP and DM for peripheral and host modes

•1.5 kΩ pull-up resistor on DP for full-speed peripheral mode

•15 kΩ bus terminations on DP and DM for host and OTG modes

For details on controlling resistor settings, see Tab le 8 .

7.4 Voltage regulator

The ISP1507 contains a built-in voltage regulator that conditions the VCC supply for use

inside the ISP1507. The voltage regulator:

•Supports input supply range of 3.0 V < VCC <3.6V

•Supplies internal circuitry with 1.8 V and 3.3 V

Remark: The REG1V8 and REG3V3 pins require external decoupling capacitors. For

details, see Section 16.

7.5 Crystal oscillator and PLL

The ISP1507 has a built-in crystal oscillator and a Phase-Locked Loop (PLL) for clock

generation.

The crystal oscillator takes a sine-wave input from an external crystal on the XTAL1 pin,

and converts it to a square wave clock for internal use. Alternatively, a square wave clock

of the same frequency can also be directly driven into the XTAL1 pin. Using an existing

square wave clock can save the cost of a crystal and also reduce the board size.

The PLL takes the square wave clock from the crystal oscillator and multiplies or divides it

into various frequencies for internal use.

The PLL produces the following frequencies, irrespective of the clock source:

•60 MHz clock for the ULPI interface controller

•1.5 MHz for the low-speed USB data

•12 MHz for the full-speed USB data

•480 MHz for the high-speed USB data

•Other internal frequencies for data conversion and data recovery

7.6 OTG module

This module contains several sub-blocks that provide all the functionality required by the

USB OTG specification. Specifically, it provides the following circuits:

•The ID detector to sense the ID pin of the micro-USB cable. The ID pin dictates which

device is initially configured as the host and which as the peripheral.

•VBUS comparators to determine the VBUS voltage level. This is required for the VBUS

detection, SRP and HNP.

Product data sheet Rev. 03 — 22 October 2009 10 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

•Resistors to temporarily charge and discharge VBUS. This is required for SRP.

•Charge pump to provide 5 V power on VBUS. The downstream peripheral can draw its

power from the ISP1507 VBUS.

7.6.1 ID detector

The ID detector detects which end of the micro-USB cable is plugged in. The detector

must first be enabled by setting the ID_PULLUP register bit to logic 1. If the ISP1507

senses a value on ID that is different from the previously reported value, an RXCMD

status update will be sent to the USB link, or an interrupt will be asserted.

•If the micro-B end of the cable is plugged in, the ISP1507 will report that ID_GND is

logic 1. The USB link must change to peripheral mode.

•If the micro-A end of the cable is plugged in, the ISP1507 will report that ID_GND is

logic 0. The USB link must change to host mode.

7.6.2 VBUS comparators

The ISP1507 provides three comparators, VBUS valid comparator, session valid

comparator and session end comparator, to detect the VBUS voltage level.

7.6.2.1 VBUS valid comparator

This comparator is used by hosts and A-devices to determine whether the voltage on

VBUS is at a valid level for operation. The ISP1507 minimum threshold for the VBUS valid

comparator is 4.4 V. Any voltage on VBUS below this threshold is considered invalid.

During power-up, it is expected that the comparator output will be ignored.

7.6.2.2 Session valid comparator

The session valid comparator is a TTL-level input that determines when VBUS is high

enough for a session to start. Peripherals, A-devices and B-devices use this comparator

to detect when a session is started. The A-device also uses this comparator to determine

when a session is completed. The session valid threshold of the ISP1507 is VB_SESS_VLD,

with a hysteresis of Vhys(B_SESS_VLD).

7.6.2.3 Session end comparator

The ISP1507 session end comparator determines when VBUS is below the B-device

session end threshold. The B-device uses this threshold to determine when a session has

ended. The session end threshold of the ISP1507 is VB_SESS_END.

7.6.3 SRP charge and discharge resistors

The ISP1507 provides on-chip resistors for short-term charging and discharging of VBUS.

These are used by the B-device to request a session, prompting the A-device to restore

the VBUS power. First, the B-device makes sure that VBUS is fully discharged from the

previous session by setting the DISCHRG_VBUS register bit to logic 1 and waiting for

SESS_END to be logic 1. Then the B-device charges VBUS by setting the CHRG_VBUS

threshold and starts a session by turning on the VBUS power.

Product data sheet Rev. 03 — 22 October 2009 11 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

7.6.4 Charge pump

The ISP1507 uses a built-in charge pump to supply current to VBUS at a nominal voltage

of 5 V. The charge pump works as a capacitive DC-DC converter. An external holding

capacitor, Ccp(C_A)-(C_B), is required between the C_A and C_B pins as shown in Figure 3,

which also shows a typical OTG VBUS load. The value of Ccp(C_A)-(C_B) depends on the

amount of current drive required. If the internal charge pump is not used, the Ccp(C_A)-(C_B)

capacitor is not required.

For details on the C_A and C_B pins, see Section 7.9.8.

7.7 Band gap reference voltage

The band gap circuit provides a stable internal voltage reference to bias the analog

circuitry. The band gap requires an accurate external reference, RRREF, resistor

connected between the RREF pin and GND. For details, see Section 16.

7.8 Power-On Reset (POR)

The ISP1507 has an internal power-on reset circuit that resets all internal logic on

power-up. The ULPI interface is also reset on power-up.

Remark: When CLOCK starts toggling after power-up, the USB link must issue a reset

command over the ULPI bus to ensure correct operation of the ISP1507.

7.9 Detailed description of pins

7.9.1 DATA[7:0]

The ISP1507 is a Physical layer (PHY) containing a USB transceiver. DATA[7:0] is the

bidirectional data bus. The USB link must drive DATA[7:0] to LOW when the ULPI bus is

idle. When the link has data to transmit to the PHY, it drives a nonzero value.

The data bus can be reconfigured to carry various data types, as given in Section 8 and

Section 9.

The DATA[7:0] pins can be 3-stated by driving pin CHIP_SELECT_N to HIGH. Weak

pull-down resistors are incorporated into the DATA[7:0] pins as part of the interface protect

feature. For details, see Section 9.3.1.

Fig 3. External capacitors connection

004aab037

ISP1507

VBUS

C_B

C_A

Ccp(C_A)-(C_B)

OTG VBUS

4.7 μF0.1 μF

Product data sheet Rev. 03 — 22 October 2009 12 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

7.9.2 VCC(I/O)

The input power pin that sets the I/O voltage level. For details, see Section 12, Section 13

and Section 16. VCC(I/O) provides power to on-chip pads of the following pins:

•CHIP_SELECT_N

•CLOCK

•DATA[7:0]

•DIR

•NXT

•RESET_N

•STP

7.9.3 RREF

Resistor reference analog I/O pin. A resistor, RRREF, must be connected between RREF

and GND, as shown in Section 16. This provides an accurate voltage reference that

biases internal analog circuitry. Less accurate resistors cannot be used and will render the

ISP1507 unusable.

7.9.4 DP and DM

The DP (data plus) and DM (data minus) are USB differential data pins. These must be

connected to the D+ and D− pins of the USB receptacle.

7.9.5 FAULT

If an external VBUS overcurrent or fault circuit is used, the output fault indicator of that

circuit can be connected to the ISP1507 FAULT input pin. The ISP1507 will inform the link

of VBUS fault events by sending RXCMDs on the ULPI bus. To use the FAULT pin, the link

must:

•Set the USE_EXT_VBUS_IND register bit to logic 1.

•Set the polarity of the external fault signal using the IND_COMPL register bit.

•Set the IND_PASSTHRU register bit to logic 1.

If the FAULT pin is not used, it is recommended to connect to GND.

7.9.6 ID

For OTG implementations, the ID (identification) pin is connected to the ID pin of the

micro-USB receptacle. As defined in On-The-Go Supplement to the USB 2.0 Specification

Rev. 1.3, the ID pin dictates the initial role of the link. If ID is detected as HIGH, the link

must assume the role of a peripheral. If ID is detected as LOW, the link must assume a

host role. Roles can be swapped at a later time by using HNP.

If the ISP1507 is not used as an OTG PHY, but as a standard USB host or peripheral PHY,

the ID pin must be connected to REG3V3.

7.9.7 CPGND

CPGND indicates the analog ground for the on-board charge pump. CPGND must always

be connected to ground, even when the charge pump is not used.

Product data sheet Rev. 03 — 22 October 2009 13 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

7.9.8 C_A and C_B

The C_A and C_B pins are to connect the flying capacitor of the charge pump. The output

current capability of the charge pump depends on the value of the capacitor used, as

shown in Tab le 3. For maximum efficiency, place capacitors as close as possible to pins.

For details, see Section 16.

If the charge pump is not used, C_A and C_B must be left floating (not connected).

7.9.9 VCC

VCC is the main input supply voltage for the ISP1507. Decoupling capacitors are

recommended. For details, see Section 16.

7.9.10 PSW_N

PSW_N is an active LOW, open-drain output pin. This pin can be connected to an active

LOW, external VBUS switch or charge pump enable circuit to control the external VBUS

power source. An external pull-up resistor, Rpullup, is required when PSW_N is used. This

pin is open-drain, allowing ganged-mode power control for multiple USB ports. For

application details, see Section 16.

If the link is in host mode, it can enable the external VBUS power source by setting the

DRV_VBUS_EXT bit in the OTG_CTRL register (see Section 10.1.4) to logic 1. The

ISP1507 will drive PSW_N to LOW to enable the external VBUS power source. If the link

detects an overcurrent condition (the VBUS state in RXCMD is not 11b), it must disable the

external VBUS power source by setting DRV_VBUS_EXT to logic 0.

7.9.11 VBUS

This pin acts as an input to VBUS comparators, and also as a power pin for the charge

pump, and SRP charge and discharge resistors.

When the DRV_VBUS bit in the OTG_CTRL register (see Section 10.1.4) is set to logic 1,

the ISP1507 drives VBUS to a voltage of 4.4 V to 5.25 V, with a minimum output current

capability of 8 mA.

Fig 4. Charge pump capacitor

Table 3. Recommended charge pump capacitor value

Ccp(C_A)-(C_B) IL (max)

22 nF 8 mA

270nF 50mA

004aab038

ISP1507

VBUS

C_A

C_B Ccp(C_A)-(C_B)

Product data sheet Rev. 03 — 22 October 2009 14 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

The VBUS pin requires a capacitive load as shown in Section 16.

To prevent electrical overstress, it is strongly recommended that you attach a series

resistor on the VBUS pin (RVBUS). RVBUS must not be attached when using the ISP1507

internal charge pump. For details, see Section 16.

7.9.12 REG3V3 and REG1V8

Regulator output voltage. These supplies are used to power the ISP1507 internal digital

and analog circuits, and must not be used to power external circuits.

For correct operation of the regulator, it is recommended that you connect REG3V3 and

REG1V8 to decoupling capacitors. For examples, see Section 16.

7.9.13 XTAL1 and XTAL2

XTAL1 is the crystal input, and XTAL2 is the crystal output. The allowed frequency on the

XTAL1 pin depends on the ISP1507 product version.

If the link requires a 60 MHz clock from the ISP1507, then either a crystal must be

attached, or a clock of the same frequency must be driven into XTAL1, with XTAL2 left

floating.

If a crystal is attached, it requires external load capacitors to GND on each terminal of the

crystal. For details, see Section 16.

If at any time the system wants to stop the clock on XTAL1, the link must first put the

ISP1507 into low-power mode. The clock on XTAL1 must be restarted before low-power

mode is exited.

7.9.14 RESET_N

An active LOW asynchronous reset pin that resets all circuits in the ISP1507. The

ISP1507 contains an internal power-on reset circuit, and therefore using the RESET_N

pin is optional. If RESET_N is not used, it must be connected to VCC(I/O).

For details on using RESET_N, see Section 9.3.2.

7.9.15 DIR

ULPI direction output pin. Controls the direction of the data bus. By default, the ISP1507

holds DIR at LOW, causing the data bus to be an input. When DIR is LOW, the ISP1507

listens for data from the link. The ISP1507 pulls DIR to HIGH only when it has data to

send to the link, which is for one of two reasons:

•To send USB receive data, RXCMD status updates and register read data to the link.

•To block the link from driving the data bus during power-up, reset and low-power

(suspend) mode.

The DIR pin can also be 3-stated by driving CHIP_SELECT_N to HIGH.

For details on DIR usage, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.

Product data sheet Rev. 03 — 22 October 2009 15 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

7.9.16 STP

ULPI stop input pin. The link must assert STP to signal the end of a USB transmit packet

or a register write operation. When DIR is asserted, the link can optionally assert STP to

abort the ISP1507, causing it to deassert DIR in the next clock cycle. A weak pull-up

resistor is incorporated into the STP pin as part of the interface protect feature. For details,

see Section 9.3.1.

The STP input will be ignored when CHIP_SELECT_N is driven to HIGH.

For details on STP usage, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.

7.9.17 NXT

ULPI next data output pin. The ISP1507 holds NXT at LOW, by default. When DIR is LOW

and the link is sending data to the ISP1507, NXT will be asserted to notify the link to

provide the next data byte. When DIR is at HIGH and the ISP1507 is sending data to the

link, NXT will be asserted to notify the link that another valid byte is on the bus. NXT is not

used for register read data or the RXCMD status update.

The NXT pin can also be 3-stated by driving CHIP_SELECT_N to HIGH.

For details on NXT usage, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.

7.9.18 CLOCK

A 60 MHz interface clock to synchronize the ULPI bus. The ISP1507 provides two

clocking options:

•A crystal attached between the XTAL1 and XTAL2 pins.

•A clock driven into the XTAL1 pin, with the XTAL2 pin left floating.

For details on CLOCK usage, refer to UTMI+ Low Pin Interface (ULPI) Specification

Rev. 1.1.

7.9.19 CHIP_SELECT_N

Active LOW chip select pin. If CHIP_SELECT_N is not used, it must be connected to

GND. For more information on using CHIP_SELECT_N, see Section 9.3.3.

7.9.20 GND (die pad)

Global ground signal, except for the charge pump that uses CPGND. The die pad is

exposed on the underside of the package as a ground plate. This acts as a ground to all

circuits in the ISP1507, except the charge pump. To ensure correct operation of the

ISP1507, GND must be soldered to the cleanest ground available.

Product data sheet Rev. 03 — 22 October 2009 16 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

8. Modes of operation

8.1 ULPI modes

The ISP1507 ULPI bus can be programmed to operate in four modes. Each mode

reconfigures the signals on the data bus as described in the following subsections. Setting

more than one mode will lead to undefined behavior.

8.1.1 Synchronous mode

This is default mode. At power-up, and when CLOCK is stable, the ISP1507 will enter

synchronous mode. The link must synchronize all ULPI signals to CLOCK, meeting the

set-up time and the hold time as defined in Section 15. A description of the ULPI pin

behavior in synchronous mode is given in Tab le 4 .

This mode is used by the link to perform the following tasks:

•High-speed detection handshake (chirp)

•Transmit and receive USB packets

•Read and write to registers

•Receive USB status updates (RXCMDs)

For more information on various synchronous mode protocols, see Section 9.

Table 4. ULPI signal description

Signal

name

Direction

on ISP1507

Signal description

CLOCK O 60 MHz interface clock. If a crystal is attached or a clock is driven into

the XTAL1 pin, the ISP1507 will drive a 60 MHz output clock.

DATA[7:0] I/O 8-bit data bus. In synchronous mode, the link drives DATA[7:0] to LOW

by default. The link initiates transfers by sending a nonzero data pattern

called TXCMD (transmit command). In synchronous mode, the direction

of DATA[7:0] is controlled by DIR. Contents of DATA[7:0] lines must be

ignored for exactly one clock cycle whenever DIR changes value. This

is called the turnaround cycle.

Data lines have fixed direction and different meaning in low-power and

serial modes.

Product data sheet Rev. 03 — 22 October 2009 17 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

8.1.2 Low-power mode

When the USB is idle, the link can place the ISP1507 into low-power mode (also called

suspend mode). In low-power mode, the data bus definition changes to that shown in

Tab l e 5 . To enter low-power mode, the link sets the SUSPENDM bit in the FUNC_CTRL

signal. The ISP1507 will draw only suspend current from the VCC supply (see Tab l e 4 6).

During low-power mode, the clock on XTAL1 may be stopped. The clock must be started

again before asserting STP to exit low-power mode. After exiting low-power mode, the

ISP1507 will send an RXCMD to the link if a change was detected in any interrupt source,

and the change still exists. An RXCMD may not be sent if the interrupt condition is

removed before exiting.

For more information on low-power mode enter and exit protocols, refer to UTMI+ Low Pin

Interface (ULPI) Specification Rev. 1.1.

DIR O Direction: Controls the direction of data bus DATA[7:0]. In synchronous

mode, the ISP1507 drives DIR to LOW by default, making the data bus

an input so that the ISP1507 can listen for TXCMDs from the link. The

ISP1507 drives DIR to HIGH only when it has data for the link. When

DIR and NXT are HIGH, the byte on the data bus contains decoded

USB data. When DIR is HIGH and NXT is LOW, the byte contains status

information called RXCMD (receive command). The only exception to

this rule is when the PHY returns register read data, where NXT is also

LOW, replacing the usual RXCMD byte. Every change in DIR causes a

turnaround cycle on the data bus, during which DATA[7:0] is not valid

and must be ignored by the link.

DIR is always asserted during low-power and serial modes.

STP I Stop: In synchronous mode, the link drives STP to HIGH for one cycle

after the last byte of data is sent to the ISP1507. The link can optionally

assert STP to force DIR to be deasserted.

In low-power and serial modes, the link holds STP at HIGH to wake up

the ISP1507, causing the ULPI bus to return to synchronous mode.

NXT O Next: In synchronous mode, the ISP1507 drives NXT to HIGH to throttle

data. If DIR is LOW, the ISP1507 asserts NXT to notify the link to place

the next data byte on DATA[7:0] in the following clock cycle. If DIR is

HIGH, the ISP1507 asserts NXT to notify the link that a valid USB data

byte is on DATA[7:0] in the current cycle. The ISP1507 always drives an

RXCMD when DIR is HIGH and NXT is LOW, unless register read data

is to be returned to the link in the current cycle.

NXT is not used in low-power or serial mode.

Table 4. ULPI signal description …continued

Signal

name

Direction

on ISP1507

Signal description

Table 5. Signal mapping during low-power mode

Signal Maps to Direction Description

LINESTATE0 DATA0 O combinatorial LINESTATE0 directly driven by analog receiver

LINESTATE1 DATA1 O combinatorial LINESTATE1 directly driven by analog receiver

Product data sheet Rev. 03 — 22 October 2009 18 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

8.1.3 6-pin full-speed or low-speed serial mode

If the link requires a 6-pin serial interface to transmit and receive full-speed or low-speed

USB data, it can set the ISP1507 to 6-pin serial mode. In 6-pin serial mode, the DATA[7:0]

bus definition changes to that shown in Ta b l e 6. To enter 6-pin serial mode, the link sets

the 6PIN_FSLS_SERIAL bit in the INTF_CTRL register (see Section 10.1.3) to logic 1. To

exit 6-pin serial mode, the link asserts STP. This is provided primarily for links that contain

legacy full-speed or low-speed functionality, providing a more cost-effective upgrade path

to high-speed. An interrupt pin is also provided to inform the link of USB events. If the link

requires CLOCK to be running during 6-pin serial mode, the CLOCK_SUSPENDM

For more information on 6-pin serial mode enter and exit protocols, refer to UTMI+ Low

Pin Interface (ULPI) Specification Rev. 1.1.

8.1.4 3-pin full-speed or low-speed serial mode

If the link requires a 3-pin serial interface to transmit and receive full-speed or low-speed

USB data, it can set the ISP1507 to 3-pin serial mode. In 3-pin serial mode, the data bus

definition changes to that shown in Tabl e 7 . To enter 3-pin serial mode, the link sets the

3PIN_FSLS_SERIAL bit in the INTF_CTRL register (see Section 10.1.3) to logic 1. To exit

3-pin serial mode, the link asserts STP. This is primarily provided for links that contain

legacy full-speed or low-speed functionality, providing a more cost-effective upgrade path

to high-speed. An interrupt pin is also provided to inform the link of USB events. If the link

requires CLOCK to be running during 3-pin serial mode, the CLOCK_SUSPENDM

For more information on 3-pin serial mode enter and exit protocols, refer to UTMI+ Low

Pin Interface (ULPI) Specification Rev. 1.1.

Reserved DATA2 O reserved; the ISP1507 will drive this pin to LOW

INT DATA3 O active HIGH interrupt indication; will be asserted whenever any unmasked

interrupt occurs

Reserved DATA[7:4] O reserved; the ISP1507 will drive these pins to LOW

Table 5. Signal mapping during low-power mode …continued

Signal Maps to Direction Description

Table 6. Signal mapping for 6-pin serial mode

Signal Maps to Direction Description

TX_ENABLE DATA0 I active HIGH transmit enable

TX_DAT DATA1 I transmit differential data on DP and DM

TX_SE0 DATA2 I transmit single-ended zero on DP and DM

INT DATA3 O active HIGH interrupt indication; will be asserted whenever any

unmasked interrupt occurs

RX_DP DATA4 O single-ended receive data from DP

RX_DM DATA5 O single-ended receive data from DM

RX_RCV DATA6 O differential receive data from DP and DM

Reserved DATA7 O reserved; the ISP1507 will drive this pin to LOW

Product data sheet Rev. 03 — 22 October 2009 19 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

8.2 USB and OTG state transitions

A Hi-Speed USB peripheral, host or OTG device handles more than one electrical state as

defined in Universal Serial Bus Specification Rev. 2.0 and On-The-Go Supplement to the

USB 2.0 Specification Rev. 1.3. The ISP1507 accommodates various states through

DP_PULLDOWN and DM_PULLDOWN.

Tab l e 8 summarizes operating states. The values of register settings in Table 8 will force

resistor settings as also given in Ta ble 8 . Resistor setting signals are defined as follows:

•RPU_DP_EN enables the 1.5 kΩ pull-up resistor on DP

•RPD_DP_EN enables the 15 kΩ pull-down resistor on DP

•RPD_DM_EN enables the 15 kΩ pull-down resistor on DM

•HSTERM_EN enables the 45 Ω termination resistors on DP and DM

It is up to the link to set the desired register settings.

Table 7. Signal mapping for 3-pin serial mode

Signal Maps to Direction Description

TX_ENABLE DATA0 I active HIGH transmit enable

DAT DATA1 I/O transmit differential data on DP and DM when TX_ENABLE is HIGH

receive differential data from DP and DM when TX_ENABLE is LOW

SE0 DATA2 I/O transmit single-ended zero on DP and DM when TX_ENABLE is HIGH

receive single-ended zero from DP and DM when TX_ENABLE is LOW

INT DATA3 O active HIGH interrupt indication; will be asserted whenever any

unmasked interrupt occurs

Reserved DATA[7:4] O reserved; the ISP1507 will drive these pins to LOW

Table 8. Operating states and their corresponding resistor settings

Signaling mode Register settings Internal resistor settings

XCVR

SELECT

[1:0]

TERM

SELECT

OPMODE

[1:0]

DP_PULL

DOWN

DM_PULL

DOWN

RPU_

DP_EN

RPD_

DP_EN

RPD_

DM_EN

HSTERM

_EN

General settings

3-state drivers XXb Xb 01b Xb Xb 0b 0b 0b 0b

Power-up or

VBUS <V

B_SESS_END

01b 0b 00b 1b 1b 0b 1b 1b 0b

Host settings

Host chirp 00b 0b 10b 1b 1b 0b 1b 1b 1b

Host high-speed 00b 0b 00b 1b 1b 0b 1b 1b 1b

Host full-speed X1b 1b 00b 1b 1b 0b 1b 1b 0b

Host high-speed or

full-speed suspend

01b 1b 00b 1b 1b 0b 1b 1b 0b

Host high-speed or

full-speed resume

01b 1b 10b 1b 1b 0b 1b 1b 0b

Host low-speed 10b 1b 00b 1b 1b 0b 1b 1b 0b

Product data sheet Rev. 03 — 22 October 2009 20 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Host low-speed

suspend

10b 1b 00b 1b 1b 0b 1b 1b 0b

Host low-speed

resume

10b 1b 10b 1b 1b 0b 1b 1b 0b

Host Test J or Test K 00b 0b 10b 1b 1b 0b 1b 1b 1b

Peripheral settings

Peripheral chirp 00b 1b 10b 0b 0b 1b 0b 0b 0b

Peripheral

high-speed

00b 0b 00b 0b 0b 0b 0b 0b 1b

Peripheral full-speed 01b 1b 00b 0b 0b 1b 0b 0b 0b

Peripheral

high-speed or

full-speed suspend

01b 1b 00b 0b 0b 1b 0b 0b 0b

Peripheral

high-speed or

full-speed resume

01b 1b 10b 0b 0b 1b 0b 0b 0b

Peripheral Test J or

Test K

00b 0b 10b 0b 0b 0b 0b 0b 1b

OTG settings

OTG device

peripheral chirp

00b 1b 10b 0b 1b 1b 0b 1b 0b

OTG device

peripheral

high-speed

00b 0b 00b 0b 1b 0b 0b 1b 1b

OTG device

peripheral full-speed

01b 1b 00b 0b 1b 1b 0b 1b 0b

OTG device

peripheral

high-speed and

full-speed suspend

01b 1b 00b 0b 1b 1b 0b 1b 0b

OTG device

peripheral

high-speed and

full-speed resume

01b 1b 10b 0b 1b 1b 0b 1b 0b

OTG device

peripheral Test J or

Test K

00b 0b 10b 0b 1b 0b 0b 1b 1b

Table 8. Operating states and their corresponding resistor settings …continued

Signaling mode Register settings Internal resistor settings

XCVR

SELECT

[1:0]

TERM

SELECT

OPMODE

[1:0]

DP_PULL

DOWN

DM_PULL

DOWN

RPU_

DP_EN

RPD_

DP_EN

RPD_

DM_EN

HSTERM

_EN

Product data sheet Rev. 03 — 22 October 2009 21 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9. Protocol description

The following subsections describe the protocol for using the ISP1507.

9.1 ULPI references

The ISP1507 provides a 12-pin ULPI interface to communicate with the link. It is highly

recommended that you read UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1 and

UTMI+ Specification Rev. 1.0.

9.2 Power-On Reset (POR)

An internal POR is generated when REG1V8 rises above VPOR(trip), for at least

tw(REG1V8_H). The internal POR pulse will also be generated whenever REG1V8 drops

below VPOR(trip) for more than tw(REG1V8_L), and then rises above VPOR(trip) again. The

voltage on REG1V8 is generated from VCC.

To give a better view of the functionality, Figure 5 shows a possible curve of REG1V8. The

internal POR starts with logic 0 at t0. At t1, the detector will see the passing of the trip

level so that POR turns to logic 1 and a delay element will add another tPORP before it

drops to logic 0. If REG1V8 dips from t2 to t3 for > tw(REG1V8_L), another POR pulse is

generated. If the dip at t4 to t5 is too short, that is, < tw(REG1V8_L), the internal POR pulse

will not react and will remain LOW.

9.3 Power-up, reset and bus idle sequence

Figure 6 shows a typical start-up sequence.

On power-up, the ISP1507 performs an internal power-on reset and asserts DIR to

indicate to the link that the ULPI bus cannot be used. When the internal PLL is stable, the

ISP1507 deasserts DIR. The power-up time depends on the VCC supply rise time, the

crystal start-up time, and PLL start-up time tstartup(o)(CLOCK). Whenever DIR is asserted, the

ISP1507 drives the NXT pin to LOW and drives DATA[7:0] with RXCMD values. When

DIR is deasserted, the link must drive the data bus to a valid level. By default, the link

must drive data to LOW. When the ISP1507 initially deasserts DIR on power-up, the link

must ignore all RXCMDs until it resets the ISP1507. Before beginning USB packets, the

link must set the RESET bit in the FUNC_CTRL register (see Section 10.1.2) to reset the

ISP1507. After the RESET bit is set, the ISP1507 will assert DIR until the internal reset

completes. The ISP1507 will automatically deassert DIR and clear the RESET bit when

reset has completed. After every reset, an RXCMD is sent to the link to update USB status

information. After this sequence, the ULPI bus is ready for use and the link can start USB

operations.

Fig 5. Internal power-on reset timing

004aaa751

REG1V8

t0 t1 t2 t3 t4 t5

VPOR(trip)

tPORP POR

tPORP

Product data sheet Rev. 03 — 22 October 2009 22 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

If a crystal is attached or a clock is driven into the XTAL1 pin, the ISP1507 will drive a

60 MHz clock out from the CLOCK pin when DIR deasserts. This is shown as CLOCK in

Figure 6.

The recommended power-up sequence for the link is as follows:

1. The link waits for tREGUP, ignoring all the ULPI pin status.

2. The link may start to detect DIR status level. If DIR is detected as LOW for three clock

cycles, the link may send a RESET command.

The ULPI interface is ready for use.

Product data sheet Rev. 03 — 22 October 2009 23 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.3.1 Interface protection

By default, the ISP1507 enables a weak pull-up resistor on STP. If the STP pin is

unexpectedly HIGH at any time, the ISP1507 will protect the ULPI interface by enabling

weak pull-down resistors on DATA[7:0].

t1 = VCC and VCC(I/O) are applied to the ISP1507. The ISP1507 regulator starts to turn on.

t2 = ULPI pads detect REG1V8 rising above the REG1V8 regulator threshold and are not in 3-state. These pads may drive

either LOW or HIGH. It is recommended that the link ignores the ULPI pins status during tREGUP.

t3 = The POR threshold is reached and a POR pulse is generated. After the POR pulse, ULPI pins are driven to a defined level.

DIR is driven to HIGH and the other pins are driven to LOW.

t4 = The ISP1507 regulator is powered up and is stable.

t5 = The internal PLL is stabilized after tstartup(PLL). If the 19.2 MHz or 26 MHz clock is started before POR, the internal PLL will

be stabilized after tstartup(PLL) from POR. The CLOCK pin starts to output 60 MHz. The DIR pin will transition from HIGH to LOW.

The DIR pin will remain LOW before the link issues a RESET command to the ISP1507.

t6 = The power-up sequence is completed and the ULPI bus interface is ready for use.

Fig 6. Power-up and reset sequence required before the ULPI bus is ready for use

CLOCK

TXCMD

DIR

DATA[7:0]

STP

NXT

004aaa885

RESET command

internal clocks stable

internal reset RXCMD

update

bus idle

VCC

VCC(I/O)

REG1V8

internal

REG1V8

detector

internal

POR

XTAL1

tstartup(PLL)

t1 t2 t3 t4 t5

tREGUP

Product data sheet Rev. 03 — 22 October 2009 24 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

The interface protect feature prevents unwanted activity of the ISP1507 whenever the

ULPI interface is not correctly driven by the link. For example, when the link powers up

more slowly than the ISP1507.

The interface protect feature can be disabled by setting the INTF_PROT_DIS bit to

logic 1.

9.3.2 Interface behavior with respect to RESET_N

The use of the RESET_N pin is optional. When RESET_N is asserted (LOW), the

ISP1507 will assert DIR. All logic in the ISP1507 will be reset, including the analog

circuitry and ULPI registers. During reset, the link must drive DATA[7:0] and STP to LOW;

otherwise undefined behavior may result. When RESET_N is deasserted (HIGH), the DIR

output will deassert (LOW) four or five clock cycles later. Figure 7 shows the ULPI

interface behavior when RESET_N is asserted (LOW), and subsequently deasserted

(HIGH). The behavior of Figure 7 applies only when CHIP_SELECT_N is asserted

(LOW). If RESET_N is not used, it must be connected to VCC(I/O).

9.3.3 Interface behavior with respect to CHIP_SELECT_N

At any time that CHIP_SELECT_N is HIGH, the ISP1507 will 3-state DATA[7:0], NXT and

DIR. STP input will be ignored. The link can reuse these pins for other purposes.

When CHIP_SELECT_N is LOW, ULPI output pins operate normally. During normal

operation, the PLL is always powered, regardless of the level of CHIP_SELECT_N.

During power-up, if CHIP_SELECT_N is HIGH, the PLL is not powered up to reduce

power consumption. During power-up, if CHIP_SELECT_N is LOW, the PLL is powered

and the ISP1507 operates normally.

If CHIP_SELECT_N is HIGH:

•The DATA[7:0], NXT and DIR pins are 3-stated and ignored.

•If the ISP1507 was previously in synchronous mode, the STP pin is ignored. If the

ISP1507 was previously in serial or suspend mode, STP is used to exit.

•The pull-down resistors on DATA[7:0] are disabled.

Fig 7. Interface behavior with respect to RESET_N

CLOCK

004aaa720

STP

RESET_N

DATA[7:0]

DIR

NXT

Hi-Z (input)

Hi-Z (link must drive)

Product data sheet Rev. 03 — 22 October 2009 25 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

•The ULPI controller is forced into an idle state and any ULPI command is ignored.

Fig 8. Entering and exiting 3-state in normal mode

CLOCK

004aaa690

CHIP_

SELECT_N

entering 3-state mode exiting 3-state mode

3-stated pins

DATA[7:0]

DIR

NXT

STP input ignored

Remark: Clock timing is not to scale.

Fig 9. Entering and exiting 3-state in suspend mode

CLOCK

004aaa691

CHIP_

SELECT_N

entering

3-state mode exiting

3-state mode

3-stated pins

DATA[7:0]

DIR

NXT

STP

TXCMD DATA

entering

suspend mode exiting

suspend mode

SUSPENDM

input ignored

Product data sheet Rev. 03 — 22 October 2009 26 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.4 VBUS power and fault detection

9.4.1 Driving 5 V on VBUS

The ISP1507 provides a built-in charge pump. To enable the charge pump, the link must

set the DRV_VBUS bit in the OTG_CTRL register (see Section 10.1.4).

The ISP1507 also supports external 5 V supplies. The ISP1507 can control the external

supply using the active-LOW PSW_N open-drain output pin. To enable the external supply

by driving PSW_N to LOW, the link must set the DRV_VBUS_EXT bit in the OTG_CTRL

bits to logic 1 to enable the external supply.

Tab l e 9 summarizes settings to drive 5 V on VBUS.

9.4.2 Fault detection

The ISP1507 supports external VBUS fault detector circuits that output a digital fault

indicator signal. The indicator signal must be connected to the FAULT pin. To enable the

ISP1507 to monitor the digital fault input, the link must set the USE_EXT_VBUS_IND bit

in the OTG_CTRL register (see Section 10.1.4) and the IND_PASSTHRU bit in the

INTF_CTRL register (see Section 10.1.3) to logic 1. For details, see Figure 11.

The FAULT input pin is mapped to the A_VBUS_VLD bit in RXCMD. Any changes for the

FAULT input will trigger RXCMD carrying the FAULT condition with A_VBUS_VLD.

9.5 TXCMD and RXCMD

Commands between the ISP1507 and the link are described in the following subsections.

9.5.1 TXCMD

By default, the link must drive the ULPI bus to its idle state of 00h. To send commands and

USB packets, the link drives a nonzero value on DATA[7:0] to the ISP1507 by sending a

byte called TXCMD. Commands include USB packet transmissions, and register reads

and writes. Once the TXCMD is interpreted and accepted by the ISP1507, the NXT signal

is asserted and the link can follow up with the required number of data bytes. The TXCMD

byte format is given in Ta bl e 10 . Any values other than those in Tab l e 1 0 are illegal and

may result in undefined behavior.

Various TXCMD packet and register sequences are shown in later sections.

Table 9. OTG_CTRL register power control bits

DRV_VBUS DRV_VBUS_EXT Power source used

0 0 internal and external VBUS power sources are disabled

10 internal V

BUS charge pump is enabled

X 1 external 5 V VBUS supply is enabled

Product data sheet Rev. 03 — 22 October 2009 27 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.5.2 RXCMD

The ISP1507 communicates status information to the link by asserting DIR and sending

an RXCMD byte on the data bus. The RXCMD data byte format is given in Ta bl e 11.

The ISP1507 will automatically send an RXCMD whenever there is a change in any of the

RXCMD data fields. The link must be able to accept an RXCMD at any time; including

single RXCMDs, back-to-back RXCMDs, and RXCMDs at any time during USB receive

packets when NXT is LOW. An example is shown in Figure 10. For details and diagrams,

refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.

An RXCMD may not be sent when exiting low-power mode or serial mode, if the interrupt

condition is removed before exiting.

Table 10. TXCMD byte format

Command

type name

Command code

DATA[7:6]

Command payload

DATA[5:0]

Command

name

Command description

Idle 00b 00 0000b NOOP No operation. 00h is the idle value of the data bus.

The link must drive NOOP by default.

Packet

transmit

01b 00 0000b NOPID Transmit USB data that does not have a PID, such

as chirp and resume signaling. The ISP1507 starts

transmitting only after accepting the next data byte.

00 XXXXb PID Transmit USB packet. DATA[3:0] indicates USB

packet identifier PID[3:0].

write

10b 10 1111b EXTW Extended register write command (optional). The

8-bit address must be provided after the command is

accepted.

XX XXXXb REGW Register write command with 6-bit immediate

address.

8-bit address must be provided after the command is

accepted.

XX XXXXb REGR Register read command with 6-bit immediate

address.

Table 11. RXCMD byte format

DATA Name Description and value

1to0 LINESTATE LINESTATE signals: For a definition of LINESTATE, see Section 9.5.2.1.

DATA0 — LINESTATE[0]

DATA1 — LINESTATE[1]

3to2 V

BUS state Encoded VBUS voltage state: For an explanation of the VBUS state, see Section 9.5.2.2.

5to4 RxEvent Encoded USB event signals: For an explanation of RxEvent, see Section 9.5.2.4.

6 ID Set to the value of the ID pin.

7 ALT_INT By default, this signal is not used and is not needed in typical designs. Optionally, the link can enable

the BVALID_RISE and/or BVALID_FALL bits in the PWR_CTRL register (see Section 10.1.14).

Corresponding changes in BVALID will cause an RXCMD to be sent to the link with the ALT_INT bit

asserted.

Product data sheet Rev. 03 — 22 October 2009 28 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.5.2.1 Linestate encoding

LINESTATE[1:0] reflects the current state of DP and DM. Whenever the ISP1507 detects

a change in DP or DM, an RXCMD will be sent to the link with the new LINESTATE[1:0]

value. The value given on LINESTATE[1:0] depends on the setting of various registers.

Tab l e 1 2 shows the LINESTATE[1:0] encoding for upstream facing ports, which applies to

peripherals. Tab l e 13 shows the LINESTATE[1:0] encoding for downstream facing ports,

which applies to host controllers. Dual-role devices must choose the correct table,

depending on whether it is in peripheral or host mode.

[1] !squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.

Fig 10. Single and back-to-back RXCMDs from the ISP1507 to the link

CLOCK

RXCMD

DATA[7:0]RXCMD RXCMD

004aaa695

DIR

STP

NXT

Single RXCMD Back-to-back RXCMDs

turnaround turnaround turnaround turnaround

Table 12. LINESTATE[1:0] encoding for upstream facing ports: peripheral

DP_PULLDOWN = 0.[1]

Mode Full-speed High-speed Chirp

XCVRSELECT[1:0] 01, 11 00 00

TERMSELECT 1 0 1

LINESTATE[1:0] 00 SE0 squelch squelch

01 FS-J !squelch !squelch and HS_Differential_Receiver_Output

10 FS-K invalid !squelch and !HS_Differential_Receiver_Output

11 SE1 invalid invalid

Product data sheet Rev. 03 — 22 October 2009 29 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

[1] !squelch indicates inactive squelch. !HS_Differential_Receiver_Output indicates inactive HS_Differential_Receiver_Output.

9.5.2.2 VBUS state encoding

USB devices must monitor the VBUS voltage for purposes such as overcurrent detection,

starting a session and SRP. The VBUS state field in the RXCMD is an encoding of the

voltage level on VBUS.

The SESS_END and SESS_VLD indicators in the VBUS state are directly taken from

internal comparators built-in to the ISP1507, and encoded as shown in Table 11 and

Tab l e 1 4.

The A_VBUS_VLD indicator in the VBUS state provides several options and must be

configured based on current draw requirements. A_VBUS_VLD can input from one or

more VBUS voltage indicators, as shown in Figure 11.

A description on how to use and select the VBUS state encoding is given in

Section 9.5.2.3.

Table 13. LINESTATE[1:0] encoding for downstream facing ports: host

DP_PULLDOWN and DM_PULLDOWN = 1.[1]

Mode Low-speed Full-speed High-speed Chirp

XCVRSELECT[1:0] 10 01, 11 00 00

TERMSELECT 1 1 0 0

OPMODE[1:0] X X 00, 01 or 11 10

LINESTATE[1:0] 00 SE0 SE0 squelch squelch

01 LS-K FS-J !squelch !squelch and HS_Differential_Receiver_Output

10 LS-J FS-K invalid !squelch and !HS_Differential_Receiver_Output

11 SE1 SE1 invalid invalid

Table 14. Encoded VBUS voltage state

Value VBUS voltage SESS_END SESS_VLD A_VBUS_VLD

00 VBUS <V

B_SESS_END 100

01 VB_SESS_END ≤VBUS < VB_SESS_VLD 000

10 VB_SESS_VLD ≤VBUS < VA_VBUS_VLD X10

11 VBUS ≥VA_VBUS_VLD XX1

Product data sheet Rev. 03 — 22 October 2009 30 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.5.2.3 Using and selecting the VBUS state encoding

The VBUS state encoding is shown in Table 11. The ISP1507 will send an RXCMD to the

link whenever there is a change in the VBUS state. To receive VBUS state updates, the link

must first enable the corresponding interrupts in the USB_INTR_EN_R_E and

USB_INTR_EN_F_E registers.

The link can use the VBUS state to monitor VBUS and take appropriate action. Table 15

shows the recommended usage for typical applications.

Standard USB host controllers: For standard hosts, the system must be able to provide

500 mA on VBUS in the range of 4.75 V to 5.25 V. An external circuit must be used to

detect overcurrent conditions. If the external overcurrent detector provides a digital fault

signal, then the fault signal must be connected to the ISP1507 FAULT input pin, and the

link must do the following:

1. Set the IND_COMPL bit in the INTF_CTRL register (see Section 10.1.3) to logic 0 or

logic 1, depending on the polarity of the external fault signal.

2. Set the USE_EXT_VBUS_IND bit in the OTG_CTRL register (see Section 10.1.4) to

logic 1.

3. If it is not necessary to qualify the fault indicator with the internal A_VBUS_VLD

comparator, set the IND_PASSTHRU bit in the INTF_CTRL register to logic 1.

Standard USB peripheral controllers: Standard peripherals must be able to detect

when VBUS is at a sufficient level for operation. SESS_VLD must be enabled to detect the

start and end of USB peripheral operations. Detection of A_VBUS_VLD and SESS_END

thresholds is not needed for standard peripherals.

Fig 11. RXCMD A_VBUS_VLD indicator source

004aaa698

VBUS (0, X)

(1, 0)

FAULT

IND_COMPL

(1, 1)

USE_EXT_VBUS_IND,

IND_PASSTHRU

RXCMD

A_VBUS_VLD

A_VBUS_VLD comparator

internal A_VBUS_VLD

complement

output

FAULT indicator

Table 15. VBUS indicators in RXCMD required for typical applications

Application A_VBUS_VLD SESS_VLD SESS_END

Standard host yes no no

Standard peripheral no yes no

OTG A-device yes yes no

OTG B-device no yes yes

Product data sheet Rev. 03 — 22 October 2009 31 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

OTG devices: When an OTG device is configured as an OTG A-device, it must be able to

provide a minimum of 8 mA on VBUS. If the OTG A-device provides less than 100 mA,

then there is no need for an overcurrent detection circuit because the internal

A_VBUS_VLD comparator is sufficient. If the OTG A-device provides more than 100 mA

on VBUS, an overcurrent detector must be used and Section “Standard USB host

controllers” applies. The OTG A-device also uses SESS_VLD to detect when an OTG

B-device is initiating VBUS pulsing SRP.

When an OTG device is configured as an OTG B-device, SESS_VLD must be used to

detect when VBUS is at a sufficient level for operation. SESS_END must be used to detect

when VBUS has dropped to a LOW level, allowing the B-device to safely initiate VBUS

pulsing SRP.

9.5.2.4 RxEvent encoding

The RxEvent field (see Table 16) of the RXCMD informs the link of information related

packets received on the USB bus. RxActive and RxError are defined in USB 2.0

Transceiver Macrocell Interface (UTMI) Specification Ver. 1.05. HostDisconnect is defined

in UTMI+ Specification Rev. 1.0. A short definition is also given in the following

subsections.

RxActive: When the ISP1507 has detected a SYNC pattern on the USB bus, it signals an

RxActive event to the link. An RxActive event can be communicated using two methods.

The first method is for the ISP1507 to simultaneously assert DIR and NXT. The second

method is for the ISP1507 to send an RXCMD to the link with the RxActive field in

RxEvent bits set to logic 1. The link must be able to detect both methods. RxActive frames

the receive packet from the first byte to the last byte.

The link must assume that RxActive is set to logic 0 when indicated in an RXCMD or when

DIR is deasserted, whichever occurs first.

The link uses RxActive to time high-speed packets and ensure that bus turnaround times

are met. For more information on the USB packet timing, see Section 9.8.1.

RxError: When the ISP1507 has detected an error while receiving a USB packet, it

deasserts NXT and sends an RXCMD with the RxError field set to logic 1. The received

packet is no longer valid and must be dropped by the link.

HostDisconnect: HostDisconnect is encoded into the RxEvent field of the RXCMD.

HostDisconnect is valid only when the ISP1507 is configured as a host (both

DP_PULLDOWN and DM_PULLDOWN are set to logic 1), and indicates to the host

controller when a peripheral is connected or disconnected. The host controller must

enable HostDisconnect by setting the HOST_DISCON_R and HOST_DISCON_F bits in

the USB_INTR_EN_R_E and USB_INTR_EN_F_E registers, respectively. Changes in

HostDisconnect will cause the PHY to send an RXCMD to the link with the updated value.

Table 16. Encoded USB event signals

Value RxActive RxError HostDisconnect

00 0 0 0

01 1 0 0

11 1 1 0

10 X X 1

Product data sheet Rev. 03 — 22 October 2009 32 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.6 Register read and write operations

Figure 12 shows register read and write sequences. The ISP1507 supports immediate

addressing and extended addressing register operations. Extended register addressing is

optional for links. Note that register operations will be aborted if the ISP1507 unexpectedly

asserts DIR during the operation. When a register operation is aborted, the link must retry

until successful. For more information on register operations, refer to UTMI+ Low Pin

Interface (ULPI) Specification Rev. 1.1.

9.7 USB reset and high-speed detection handshake (chirp)

Figure 13 shows the sequence of events for USB reset and high-speed detection

handshake (chirp). The sequence is shown for hosts and peripherals. Figure 13 does not

show all RXCMD updates and timing is not to scale. The sequence is as follows:

1. USB reset: The host detects a peripheral attachment as low-speed if DM is HIGH and

as full-speed if DP is HIGH. If a host detects a low-speed peripheral, it does not follow

the remainder of this protocol. If a host detects a full-speed peripheral, it resets the

peripheral by writing to the Function Control register (see Section 10.1.2).

XCVRSELECT[1:0] = 00b (high-speed) and TERMSELECT = 0b are then set which

drives SE0 on the bus (DP and DM are connected to ground through 45 Ω). The host

also sets OPMODE[1:0] = 10b for correct chirp transmit and receive. The start of SE0

is labeled T0.

Remark: To receive chirp signaling, the host must also consider the high-speed

differential receiver output. The host controller must interpret LINESTATE[1:0] as

shown in Tabl e 1 3 .

2. High-speed detection handshake (chirp)

a. Peripheral chirp: After detecting SE0 for no less than 2.5 μs, if the peripheral is

capable of high-speed, it sets XCVRSELECT[1:0] = 00b (high-speed) and

OPMODE[1:0] = 10b (chirp). The peripheral immediately follows this with a

TXCMD (NOPID), transmitting a Chirp K for no less than 1 ms and ending no more

AD indicates the address byte, and D indicates the data byte.

Fig 12. Example of register write, register read, extended register write and extended register read

CLOCK

DIR

DATA[7:0]

NXT

004aaa710

DTXCMD

(EXTW) AD D

immediate

TXCMD

(REGW) TXCMD

(REGR) DAD

TXCMD

(EXTW) D

STP

extended

Product data sheet Rev. 03 — 22 October 2009 33 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

than 7 ms after reset time T0. If the peripheral is in low-power mode, it must wake

up its clock within 5.6 ms, leaving 200 μs for the link to start transmitting the

Chirp K, and 1.2 ms for the Chirp K to complete (worst case with 10 % slow clock).

b. Host chirp: If the host does not detect the peripheral chirp, it must continue

asserting SE0 until the end of reset. If the host detects the peripheral Chirp K for

no less than 2.5 μs, then no more than 100 μs after the bus leaves the Chirp K

state, the host sends a TXCMD (NOPID) with an alternating sequence of Chirp Ks

and Js. Each Chirp K or Chirp J must last no less than 40 μs and no longer than

60 μs.

c. High-speed idle: The peripheral must detect a minimum of Chirp K-J-K-J-K-J. Each

Chirp K and Chirp J must be detected for at least 2.5 μs. The peripheral sets

TERMSELECT = 0b and OPMODE[1:0] = 00b after seeing the minimum Chirp

sequence. The peripheral is now in high-speed mode and sees !squelch (01b on

LINESTATE). When the peripheral sees squelch (10b on LINESTATE), it knows

that the host has completed chirp and waits for Hi-Speed USB traffic to begin. After

transmitting the chirp sequence, the host changes OPMODE[1:0] to 00b and

begins sending USB packets.

For more information, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.

Product data sheet Rev. 03 — 22 October 2009 34 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Timing is not to scale.

Fig 13. USB reset and high-speed detection handshake (chirp) sequence

004aaa711

DATA

[7:0]

TXCMD

NOPID J... TXCMD

(REGW)

TXCMD

(REGW) SE0 K

DIR

STP

NXT

XCVR

SELECT

TERM

SELECT

01 (FS) 00 (HS)

MODE

00 (normal) 01 (chirp) 00 (normal)

LINE

STATE

J (01b) SE0 (00b) peripheral chirp K (10b) squelch (00b)

host chirp K (10b) or chirp J (01b)

squelch

(00b)

ULPI host

DATA

[7:0]

TXCMD

NOPID K...

SE0 TXCMD

(REGW) 00 KJKJKJTXCMD

(REGW) 00

DIR

STP

NXT

XCVR

SELECT

01 (FS) 00 (HS)

TERM

SELECT

MODE

00 (normal) 10 (chirp) 00 (normal)

LINE

STATE

J (01b) SE0 (00b) peripheral chirp K (10b) !squelch

(01b)

host chirp K or J (10b or 01b)

squelch

(00b) squelch (00b)

ULPI peripheral

USB signals

USB reset high-speed detection handshake (chirp)

peripheral chirp host chirp HS idle

RXCMDs

Product data sheet Rev. 03 — 22 October 2009 35 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.8 USB packet transmit and receive

An example of a packet transmit and receive is shown in Figure 14. For details on USB

packets, refer to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1.

9.8.1 USB packet timing

9.8.1.1 ISP1507 pipeline delays

The ISP1507 delays are shown in Tab l e 1 7. For a detailed description, refer to UTMI+

Low Pin Interface (ULPI) Specification Rev. 1.1, Section 3.8.2.6.2.

[1] According to UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1, Section 3.8.2.6, the TX and RX start or end delays must be used

for high-speed inter-packet timing. If the link uses RXCMDs for high-speed inter-packet timing, the result cannot be guaranteed.

Fig 14. Example of using the ISP1507 to transmit and receive USB data

CLOCK

TXCMD

DATA[7:0] RXCMD DATA

DIR

STP

NXT

004aab039

link sends

TXCMD

ISP1507

accepts

TXCMD

link sends

the next data;

ISP1507

accepts link signals

end of data ULPI bus

is idle

ISP1507

asserts DIR,

causing

turnaround

cycle

ISP1507

sends

RXCMD

(NXT LOW)

ISP1507

sends

USB data

(NXT HIGH)

ISP1507

deasserts

DIR, causing

turnaround

cycle

turnaround turnaround

DATA

Table 17. PHY pipeline delays

Parameter name[1] High-speed PHY delay Full-speed PHY delay Low-speed PHY delay

RXCMD delay (J and K) 4 4 4

RXCMD delay (SE0) 4 4 to 6 16 to 18

TX start delay 1 to 2 6 to 10 74 to 75

TX end delay (packets) 3 to 4 not applicable not applicable

TX end delay (SOF) 6 to 9 not applicable not applicable

RX start delay 5 to 6 not applicable not applicable

RX end delay 5 to 6 17 to 18 122 to 123

Product data sheet Rev. 03 — 22 October 2009 36 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.8.1.2 Allowed link decision time

The amount of clock cycles allocated to the link to respond to a received packet and

correctly receive back-to-back packets is given in Table 18. Link designs must follow

values given in Tabl e 1 8 for correct USB system operation. Examples of high-speed

packet sequences and timing are shown in Figure 15 and Figure 16. For details, refer to

UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1, Section 3.8.2.6.3.

Table 18. Link decision times

Packet sequence High-speed

link delay

Full-speed

link delay

Low-speed

link delay

Definition

Transmit-Transmit

(host only)

15 to 24 7 to 18 77 to 247 Number of clock cycles a host link must wait before driving

the TXCMD for the second packet.

In high-speed, the link starts counting from the assertion of

STP for the first packet.

In full-speed, the link starts counting from the RXCMD,

indicating LINESTATE has changed from SE0 to J for the

first packet. The timing given ensures inter-packet delays of

2 bit times to 6.5 bit times.

Receive-Transmit

(host or

peripheral)

1 to 14 7 to 18 77 to 247 Number of clock cycles the link must wait before driving the

TXCMD for the transmit packet.

In high-speed, the link starts counting from the end of the

receive packet; deassertion of DIR or an RXCMD, indicating

RxActive is LOW.

In full-speed or low-speed, the link starts counting from the

RXCMD, indicating LINESTATE has changed from SE0 to J

for the receive packet. The timing given ensures inter-packet

delays of 2 bit times to 6.5 bit times.

Receive-Receive

(peripheral only)

1 1 1 Minimum number of clock cycles between consecutive

receive packets. The link must be able to receive both

packets.

Transmit-Receive

(host or

peripheral)

92 80 718 Host or peripheral transmits a packet and will time-out after

this number of clock cycles if a response is not received. Any

subsequent transmission can occur after this time.

Product data sheet Rev. 03 — 22 October 2009 37 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.9 Preamble

Preamble packets are headers to low-speed packets that must travel over a full-speed

bus, between a host and a hub. To enter preamble mode, the link sets

XCVRSELECT[1:0] = 11b in the FUNC_CTRL register (see Section 10.1.2). When in

Fig 15. High-speed transmit-to-transmit packet timing

004aaa712

DP or

DM DATA EOP IDLE SYNC

CLOCK

DN−1DN

DATA

[7:0]

TXCMD D1

DIR

STP

NXT

TX end delay (two to five clocks) link decision time (15 to 24 clocks) TX start delay

(one to two clocks)

USB interpacket delay (88 to 192 high-speed bit times)

Fig 16. High-speed receive-to-transmit packet timing

004aaa713

DP or

DM DATA EOP IDLE SYNC

CLOCK

DN−4

DN−3

DATA

[7:0]

TXCMD D1

DIR

STP

NXT

RX end delay

(three to eight clocks) link decision time (1 to 14 clocks) TX start delay

(one to two clocks)

USB interpacket delay (8 to 192 high-speed bit times)

DN−2

DN−1

turnaround

Product data sheet Rev. 03 — 22 October 2009 38 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

preamble mode, the ISP1507 operates just as in full-speed mode, and sends all data with

the full-speed rise time and fall time. Whenever the link transmits a USB packet in

preamble mode, the ISP1507 will automatically send a preamble header at full-speed bit

rate before sending the link packet at low-speed bit rate. The ISP1507 will ensure a

minimum gap of four full-speed bit times between the last bit of the full-speed PRE PID

and the first bit of the low-speed packet SYNC. The ISP1507 will drive a J for at least one

full-speed bit time after sending the PRE PID, after which the pull-up resistor can hold the

J state on the bus. An example transmit packet is shown in Figure 17.

In preamble mode, the ISP1507 can also receive low-speed packets from the full-speed

bus.

9.10 USB suspend and resume

9.10.1 Full-speed or low-speed host-initiated suspend and resume

Figure 18 illustrates how a host or a hub places a full-speed or low-speed peripheral into

suspend and sometime later initiates resume signaling to wake up the downstream

peripheral. Note that Figure 18 timing is not to scale, and does not show all RXCMD

LINESTATE updates.

The sequence of events for a host and a peripheral, both with ISP1507, is as follows:

1. Idle: Initially, the host and the peripheral are idle. The host has its 15 kΩ pull-down

resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b) and 45 Ω

terminations disabled (TERMSELECT is set to 1b). The peripheral has the 1.5 kΩ

pull-up resistor connected to DP for full-speed or DM for low-speed (TERMSELECT is

set to 1b).

2. Suspend: When the peripheral sees no bus activity for 3 ms, it enters the suspend

state. The peripheral link places the PHY into low-power mode by clearing the

SUSPENDM bit in the FUNC_CTRL register (see Section 10.1.2), causing the PHY to

draw only suspend current. The host may or may not be powered down.

DP and DM timing is not to scale.

Fig 17. Preamble sequence

CLOCK

TXCMD (low-speed packet ID) D1

DATA[7:0]

DIR

STP

NXT

004aaa714

DP or DM FS SYNC FS

PRE ID IDLE (min

4 FS bits) LS SYNC LS PID LS D0 LS D1

Product data sheet Rev. 03 — 22 October 2009 39 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE[1:0] to

10b and transmits a K for at least 20 ms. The peripheral link sees the resume K on

LINESTATE, and asserts STP to wake up the PHY.

4. EOP: When STP is asserted, the ISP1507 on the host side automatically appends an

EOP of two bits of SE0 at low-speed bit rate, followed by one bit of J. The ISP1507 on

the host side knows to add the EOP because DP_PULLDOWN and DM_PULLDOWN

are set to 1b for a host. After the EOP is completed, the host link sets OPMODE[1:0]

to 00b for normal operation. The peripheral link sees the EOP and also resumes

normal operation.

Product data sheet Rev. 03 — 22 October 2009 40 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.10.2 High-speed suspend and resume

Figure 19 illustrates how a host or a hub places a high-speed enabled peripheral into

suspend and then initiates resume signaling. The high-speed peripheral will wake up and

return to high-speed operations. Note that Figure 19 timing is not to scale, and does not

show all RXCMD LINESTATE updates.

Timing is not to scale.

Fig 18. Full-speed suspend and resume

DATA

[7:0]

TXCMD

NOPID K...

TXCMD

(REGW)

DIR

STP

NXT

OPMODE 00b 10b 00b

KTXCMD

LINE

STATE JKSE0 J

CLOCK

DATA

[7:0]

TXCMD

(REGW) LINESTATE J LINESTATE K SE0 J

DIR

STP

NXT

OPMODE 00b 10b 00b

SUSPENDM

LINE

STATE J KSE0 J

004aab123

FS or LS host (XCVRSELECT = 01b (FS)

or 10b (LS), DP_PULLDOWN = 1b,

DM_PULLDOWN = 1b, TERMSELECT = 1b)

FS or LS peripheral (XCVRSELECT = 01b (FS)

or 10b (LS), DP_PULLDOWN = 0b, TERMSELECT = 1b)

USB signals

(only FS is shown)

idle suspend resume K EOP idle

Product data sheet Rev. 03 — 22 October 2009 41 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

The sequence of events related to a host and a peripheral, both with ISP1507, is as

follows:

1. High-speed idle: Initially, the host and the peripheral are idle. The host has its 15 kΩ

pull-down resistors enabled (DP_PULLDOWN and DM_PULLDOWN are set to 1b)

and 45 Ω terminations enabled (TERMSELECT is set to 0b). The peripheral has its

45 Ω terminations enabled (TERMSELECT is set to 0b).

2. Full-speed suspend: When the peripheral sees no bus activity for 3 ms, it enters the

suspend state. The peripheral link places the ISP1507 into full-speed mode

(XCVRSELECT is set to 01b), removes 45 Ω terminations, and enables the 1.5 kΩ

pull-up resistor on DP (TERMSELECT is set to 1b). The peripheral link then places

the ISP1507 into low-power mode by clearing SUSPENDM, causing the ISP1507 to

draw only suspend current. The host also changes the ISP1507 to full-speed

(XCVRSELECT is set to 01b), removes 45 Ω terminations (TERMSELECT is set to

1b), and then may or may not be powered down.

3. Resume K: When the host wants to wake up the peripheral, it sets OPMODE to 10b

and transmits a full-speed K for at least 20 ms. The peripheral link sees the resume K

(10b) on LINESTATE, and asserts STP to wake up the ISP1507.

4. High-speed traffic: The host link sets high-speed (XCVRSELECT is set to 00b) and

enables its 45 Ω terminations (TERMSELECT is set to 0b). The peripheral link sees

SE0 on LINESTATE and also sets high-speed (XCVRSELECT is set to 00b), and

enables its 45 Ω terminations (TERMSELECT is set to 0b). The host link sets

OPMODE to 00b for normal high-speed operation.

Product data sheet Rev. 03 — 22 October 2009 42 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Timing is not to scale.

Fig 19. High-speed suspend and resume

DATA

[7:0]

TXCMD

NOPID K...

TXCMD

(REGW)

DIR

STP

NXT

MODE 00b 10b 00b

KTXCMD

(REGW)

CLOCK

DATA

[7:0]

TXCMD

(REGW) LINESTATE J LINESTATE K SE0 TXCMD

(REGW)

DIR

STP

NXT

MODE 00b 10b 00b

SUSPENDM

LINE

STATE

004aab124

ULPI HS host (DP_PULLDOWN = 1b,

DM_PULLDOWN = 1b)

ULPI HS peripheral (DP_PULLDOWN = 0b)

USB signals

HS idle FS suspend resume K

TXCMD

(REGW)

HS idle

XCVR

SELECT 00b 01b 00b

TERM

SELECT

LINE

STATE

!SQUELCH

(01b) FS J (01b) !SQUELCH

(01b)

SQUELCH (00b)

FS K (10b)

XCVR

SELECT 00b 01b 00b

TERM

SELECT

!SQUELCH

(01b) SQUELCH

(00b) FS J (01b) !SQUELCH

(01b)

SQUELCH (00b)

FS K (10b)

SQUELCH

(00b)

Product data sheet Rev. 03 — 22 October 2009 43 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.10.3 Remote wake-up

The ISP1507 supports peripherals that initiate remote wake-up resume. When placed into

USB suspend, the peripheral link remembers at what speed it was originally operating.

Depending on the original speed, the link follows one of the protocols detailed here. In

Figure 20, timing is not to scale, and not all RXCMD LINESTATE updates are shown.

The sequence of events related to a host and a peripheral, both with ISP1507, is as

follows:

1. Both the host and the peripheral are assumed to be in low-power mode.

2. The peripheral begins remote wake-up by re-enabling its clock and setting its

SUSPENDM bit to 1b.

3. The peripheral begins driving K on the bus to signal resume. Note that the peripheral

link must assume that LINESTATE is K (01b) while transmitting because it will not

receive any RXCMDs.

4. The host recognizes the resume, re-enables its clock and sets its SUSPENDM bit.

5. The host takes over resume driving within 1 ms of detecting the remote wake-up.

6. The peripheral stops driving resume.

7. The peripheral sees the host continuing to drive resume.

8. The host stops driving resume and the ISP1507 automatically adds the EOP to the

end of resume. The peripheral recognizes the EOP as the end of resume.

9. Both the host and the peripheral revert to normal operation by writing 00b to

OPMODE. If the host or the peripheral was previously in high-speed mode, it must

revert to high-speed before the SE0 of the EOP is completed. This can be achieved

by writing XCVRSELECT[1:0] = 00b and TERMSELECT = 0b after LINESTATE

indicates SE0.

Product data sheet Rev. 03 — 22 October 2009 44 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.11 No automatic SYNC and EOP generation (optional)

This setting allows the link to turn off the automatic SYNC and EOP generation, and must

be used for high-speed packets only. It is provided for backward compatibility with legacy

controllers that include SYNC and EOP bytes in the data payload when transmitting

packets. The ISP1507 will not automatically generate the SYNC and EOP patterns when

OPMODE[1:0] is set to 11b. The ISP1507 will still NRZI encode data and perform bit

stuffing. An example of a sequence is shown in Figure 21. The link must always send

packets using the TXCMD (NOPID) type. The ISP1507 does not provide a mechanism to

control bit stuffing in individual bytes, but will automatically turn off bit stuffing for EOP

when STP is asserted with data set to FEh. If data is set to 00h when STP is asserted, the

Timing is not to scale.

Fig 20. Remote wake-up from low-power mode

DATA

[7:0]

LINESTATE TXCMD

REGW TXCMD

REGW

00h

TXCMD

NOPID

DIR

STP

NXT

XCVR

SELECT 01b (FS), 10b (LS) 00b (HS only)

TERM

SELECT

MODE 10b 00b

DATA

[7:0]

LINESTATE TXCMD

REGW RXCMD

00h

TXCMD

NOPID RXCMD RXCMD TXCMD

REGW

DIR

STP

NXT

XCVR

SELECT 00b (HS), 01b (FS), 10b (LS)

00b (HS only)

TERM

SELECT

MODE 10b 00b

ULPI host

ULPI peripheral

004aaa718

0b (HS only)

Product data sheet Rev. 03 — 22 October 2009 45 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

PHY will not transmit any EOP. The ISP1507 will also detect if the PID byte is A5h,

indicating an SOF packet, and automatically send a long EOP when STP is asserted. To

transmit chirp and resume signaling, the link must set OPMODE to 10b.

9.12 On-The-Go operations

On-The-Go (OTG) is a supplement to Universal Serial Bus Specification Rev. 2.0 that

allows a portable USB device to assume the role of a limited USB host by defining

improvements, such as a small connector and low power. Non-portable devices, such as

standard hosts and embedded hosts, can also benefit from OTG features.

The ISP1507 OTG PHY is designed to support all the tasks specified in the OTG

supplement. The ISP1507 provides the front-end analog support for Host Negotiation

Protocol (HNP) and Session Request Protocol (SRP) for dual-role devices. The

supporting components include:

•Built-in 5 V charge pump

•Voltage comparators

–A_VBUS_VLD

–SESS_VLD (session valid, can be used for both A-session and B-session valid)

–SESS_END (session end)

•Pull-up and pull-down resistors on DP and DM

•ID detector indicates if micro-A or micro-B plug is inserted

•Charge and discharge resistors on VBUS

The following subsections describe how to use the ISP1507 OTG components.

Fig 21. Transmitting USB packets without automatic SYNC and EOP generation

CLOCK

DATA

[7:0]

TXCMD 00h 00h 00h 80h PID D1 D2 D3 ... ... DN − 1 FEhDN

DIR

STP

NXT

ULPI signals

TXVALID

TXREADY

TXBIT

STUFF

ENABLE

DP, DM

IDLE SYNC PID IDLEEOPDATA PAYLOAD

004aab125

UTMI+ equivalent

signals

USB bus

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  46 of 82
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
9.12.1 OTG charge pump
A description of the charge pump is given in Section 7.6.4. When the controller is 
configured as an A-device, it can provide the VBUS power by turning on the charge pump. 
Control of the charge pump is described in Section 9.4.1 and Section 10.1.4.
9.12.2 OTG comparators
The ISP1507 provides comparators that conform to On-The-Go Supplement to the 
USB 2.0 Specification Rev. 1.3 requirements of VA_VBUS_VLD, VA_SESS_VLD, VB_SESS_VLD 
and VB_SESS_END. In this data sheet, VA_SESS_VLD and VB_SESS_VLD are combined into 
VB_SESS_VLD. Comparators are described in Section 7.6.2. Changes in comparator values 
are communicated to the link by RXCMDs as described in Section 9.5.2.2. Control over 
comparators is described in Section 10.1.5 to Section 10.1.8.
9.12.3 Pull-up and pull-down resistors
The USB resistors on DP and DM can be used to initiate data-line pulsing SRP. The link 
must set the required bus state using mode settings in Tabl e 8.
9.12.4 ID detection
The ISP1507 provides an internal pull-up resistor to sense the value of the ID pin. The 
pull-up resistor must first be enabled by setting the ID_PULLUP register bit to logic 1. If 
the value on ID has changed, the ISP1507 will send an RXCMD or interrupt to the link by 
time tID. If the link does not receive any RXCMD or interrupt by tID, then the ID value has 
not changed.
9.12.5 VBUS charge and discharge resistors
A pull-up resistor, RUP(VBUS), is provided to perform VBUS pulsing SRP. A B-device is 
allowed to charge VBUS above the session valid threshold to request the host to turn on 
the VBUS power.
A pull-down resistor, RDN(VBUS), is provided for a B-device to discharge VBUS. This is done 
whenever the A-device turns off the VBUS power. The B-device can use the pull-down 
resistor to ensure VBUS is below VB_SESS_END before starting a session.
For details, refer to On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3.
9.13 Serial modes
The ISP1507 supports both 6-pin serial mode and 3-pin serial mode, controlled by 
bits 6PIN_FSLS_SERIAL and 3PIN_FSLS_SERIAL of the INTF_CTRL register (see 
Section 10.1.3). For details, refer to UTMI+ Low Pin Interface (ULPI) Specification 
Rev. 1.1, Section 3.10.
Figure 22 and Figure 23 provide examples of 6-pin serial mode and 3-pin serial mode, 
respectively.

Product data sheet Rev. 03 — 22 October 2009 47 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Fig 22. Example of transmit followed by receive in 6-pin serial mode

DATA0

(TX_ENABLE)

DATA1

(TX_DAT)

DATA2

(TX_SE0)

DATA4

(RX_DP)

DATA5

(RX_DM)

DATA6

(RX_RCV)

SYNC DATA EOP

TRANSMIT RECEIVE

SYNC DATA EOP

004aaa692

Fig 23. Example of transmit followed by receive in 3-pin serial mode

DATA0

(TX_ENABLE)

DATA1

(TX_DAT/

RX_RCV)

DATA2

(TX_SE0/

RX_SE0)

004aaa693

SYNC DATA EOP

TRANSMIT RECEIVE

SYNC DATA EOP

Product data sheet Rev. 03 — 22 October 2009 48 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

9.14 Aborting transfers

The ISP1507 supports aborting transfers on the ULPI bus. For details, refer to UTMI+ Low

Pin Interface (ULPI) Specification Rev. 1.1, Section 3.8.4.

9.15 Avoiding contention on the ULPI data bus

Because the ULPI data bus is bidirectional, avoid situations in which both the link and the

PHY simultaneously drive the data bus.

The following points must be considered while implementing the data bus drive control on

the link.

After power-up and clock stabilization, default states are as follows:

•The ISP1507 drives DIR to LOW.

•The data bus is input to the ISP1507.

•The ULPI link data bus is output, with all data bus lines driven to LOW.

When the ISP1507 wants to take control of the data bus to initiate a data transfer, it

changes the DIR value from LOW to HIGH.

At this point, the link must disable its output buffers. This must be as fast as possible so

the link must use a combinational path from DIR.

The ISP1507 will not immediately enable its output buffers, but will delay the enabling of

its buffers until the next clock edge, avoiding bus contention.

When the data transfer is no longer required by the ISP1507, it changes DIR from HIGH to

LOW and starts to immediately turn off its output drivers. The link senses the change of

DIR from HIGH to LOW, but delays enabling its output buffers for one CLOCK cycle,

avoiding data bus contention.

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  49 of 82
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
10. Register map
 
[1] Read (R): A register can be read. Read-only if this is the only mode given.
[2] Write (W): The pattern on the data bus will be written over all bits of a register.
[3] Set (S): The pattern on the data bus is OR-ed with and written to a register.
[4] Clear (C): The pattern on the data bus is a mask. If a bit in the mask is set, then the corresponding register bit will be set to zero 
(cleared).
 
[1] Read (R): A register can be read. Read-only if this is the only mode given.
[2] Write (W): The pattern on the data bus will be written over all bits of a register.
[3] Set (S): The pattern on the data bus is OR-ed with and written to a register.
[4] Clear (C): The pattern on the data bus is a mask. If a bit in the mask is set, then the corresponding register bit will be set to zero 
(cleared).
Table 19. Immediate register set overview
Field name Size (bit) Address (6 bit) References
R[1] W[2] S[3] C[4]
VENDOR_ID_LOW 8 00h - - - Section 10.1.1 on page 50
VENDOR_ID_HIGH 8 01h - - -
PRODUCT_ID_LOW 8 02h - - -
PRODUCT_ID_HIGH 8 03h - - -
FUNC_CTRL 8 04h to 06h 04h 05h 06h Section 10.1.2 on page 50
INTF_CTRL 8 07h to 09h 07h 08h 09h Section 10.1.3 on page 51
OTG_CTRL 8 0Ah to 0Ch 0Ah 0Bh 0Ch Section 10.1.4 on page 52
USB_INTR_EN_R_E 8 0Dh to 0Fh 0Dh 0Eh 0Fh Section 10.1.5 on page 54
USB_INTR_EN_F_E 8 10h to 12h 10h 11h 12h Section 10.1.6 on page 54
USB_INTR_STAT 8 13h - - - Section 10.1.7 on page 55
USB_INTR_L 8 14h - - - Section 10.1.8 on page 55
DEBUG 8 15h - - - Section 10.1.9 on page 56
SCRATCH 8 16h to 18h 16h 17h 18h Section 10.1.10 on page 56
Reserved (do not use) - 19h to 2Eh Section 10.1.11 on page 56
Access extended register set 8 - 2Fh - - Section 10.1.12 on page 56
Vendor-specific registers 8 30h to 3Ch Section 10.1.13 on page 57
PWR_CTRL 8 3Dh to 3Fh Section 10.1.14 on page 57
Table 20. Extended register set overview
Field name Size 
(bit)
Address (6 bit) References
R[1] W[2] S[3] C[4]
Maps to immediate register set above 8 00h to 3Fh Section 10.2 on page 57
Reserved (do not use) 8 40h to FFh

Product data sheet Rev. 03 — 22 October 2009 50 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

10.1 Immediate register set

10.1.1 Vendor ID and Product ID registers

10.1.1.1 VENDOR_ID_LOW register

Tab l e 2 1 shows the bit description of the register.

10.1.1.2 VENDOR_ID_HIGH register

The bit description of the register is given in Tabl e 2 2 .

10.1.1.3 PRODUCT_ID_LOW register

The bit description of the PRODUCT_ID_LOW register is given in Table 23.

10.1.1.4 PRODUCT_ID_HIGH register

The bit description of the register is given in Tabl e 2 4 .

10.1.2 FUNC_CTRL register

This register controls UTMI function settings of the PHY. The bit allocation of the register

is given in Tab l e 2 5 .

Table 21. VENDOR_ID_LOW - Vendor ID Low register (address R = 00h) bit description

Legend: * reset value

Bit Symbol Access Value Description

7 to 0 VENDOR_ID_

LOW[7:0]

RCCh*Vendor ID Low: Lower byte of the ST-Ericsson vendor ID supplied by

USB-IF; has a fixed value of CCh

Table 22. VENDOR_ID_HIGH - Vendor ID High register (address R = 01h) bit description

Legend: * reset value

Bit Symbol Access Value Description

7 to 0 VENDOR_ID_

HIGH[7:0]

R 04h* Vendor ID High: Upper byte of the ST-Ericsson vendor ID supplied by

USB-IF; has a fixed value of 04h

Table 23. PRODUCT_ID_LOW - Product ID Low register (address R = 02h) bit description

Legend: * reset value

Bit Symbol Access Value Description

7 to 0 PRODUCT_ID_

LOW[7:0]

R 04h* Product ID Low: Lower byte of the ST-Ericsson product ID number; has

a fixed value of 04h

Table 24. PRODUCT_ID_HIGH - Product ID High register (address R = 03h) bit description

Legend: * reset value

Bit Symbol Access Value Description

7 to 0 PRODUCT_ID_

HIGH[7:0]

R 15h* Product ID High: Upper byte of the ST-Ericsson product ID number; has

a fixed value of 15h

Table 25. FUNC_CTRL - Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved SUSPENDM RESET OPMODE[1:0] TERM

SELECT

XCVRSELECT[1:0]

Reset 0 1000001

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Product data sheet Rev. 03 — 22 October 2009 51 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

10.1.3 INTF_CTRL register

The INTF_CTRL register enables alternative interfaces. All of these modes are optional

features provided for legacy link cores. Setting more than one of these fields results in

undefined behavior. Table 27 provides the bit allocation of the register.

Table 26. FUNC_CTRL - Function Control register (address R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit

description

Bit Symbol Description

7 - reserved

6 SUSPENDM Suspend LOW: Active LOW PHY suspend.

Places the PHY into low-power mode. The PHY will power down all blocks, except the

full-speed receiver, OTG comparators and ULPI interface pins.

To come out of low-power mode, the link must assert STP. The PHY will automatically clear

this bit when it exits low-power mode.

0b — Low-power mode

1b — Powered (default)

5 RESET Reset: Active HIGH transceiver reset.

After the link sets this bit, the PHY will assert DIR and reset the digital core. This does not

reset the ULPI interface or the ULPI register set.

When reset is completed, the PHY will deassert DIR and automatically clear this bit, followed

by an RXCMD update to the link.

0b — Do not reset (default)

1b — Reset

The link must wait for DIR to deassert before using the ULPI bus. Does not reset the ULPI

interface or the ULPI register set.

4 to 3 OPMODE[1:0] Operation Mode: Selects the required bit-encoding style during transmit.

00b — Normal operation (default)

01b — Non-driving

10b — Disable bit-stuffing and NRZI encoding

11b — Do not automatically add SYNC and EOP when transmitting; must be used only for

high-speed packets

2 TERMSELECT Termination Select: Controls the internal 1.5 kΩ full-speed pull-up resistor and 45 Ω

high-speed terminations. Control over bus resistors changes, depending on

XCVRSELECT[1:0], OPMODE[1:0], DP_PULLDOWN and DM_PULLDOWN, as shown in

Table 8.

1 to 0 XCVRSELECT

[1:0]

Transceiver Select: Selects the required transceiver speed.

00b — Enable the high-speed transceiver

01b — Enable the full-speed transceiver (default)

10b — Enable the low-speed transceiver

11b — Enable the full-speed transceiver for low-speed packets (full-speed preamble is

automatically prefixed)

Table 27. INTF_CTRL - Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol INTF_

PROT_DIS

IND_PASS

THRU

IND_

COMPL

reserved CLOCK_

SUSPENDM

reserved 3PIN_FSLS

_SERIAL

6PIN_FSLS

_SERIAL

Reset 0000 0000

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Product data sheet Rev. 03 — 22 October 2009 52 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

10.1.4 OTG_CTRL register

This register controls various OTG functions of the ISP1507. The bit allocation of the

OTG_CTRL register is given in Tabl e 29 .

Table 28. INTF_CTRL - Interface Control register (address R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit

description

Bit Symbol Description

7INTF_PROT_DISInterface Protect Disable: Controls circuitry built into the ISP1507 to protect the ULPI

interface when the link 3-states STP and DATA[7:0]. When this bit is enabled, the ISP1507

will automatically detect when the link stops driving STP.

0b — Enables the interface protect circuit (default). The ISP1507 attaches a weak pull-up

resistor on STP. If STP is unexpectedly HIGH, the ISP1507 attaches weak pull-down

resistors on DATA[7:0], protecting data inputs.

1b — Disables the interface protect circuit, detaches weak pull-down resistors on

DATA[7:0], and a weak pull-up resistor on STP.

6 IND_PASSTHRU Indicator Pass-through: Controls whether the complement output is qualified with the

internal A_VBUS_VLD comparator before being used in the VBUS state in RXCMD. For

details, see Section 9.5.2.2.

0b — The complement output signal is qualified with the internal A_VBUS_VLD comparator

(default).

1b — The complement output signal is not qualified with the internal A_VBUS_VLD

comparator.

5IND_COMPL Indicator Complement: Informs the PHY to invert the FAULT input signal, generating the

complement output. For details, see Section 9.5.2.2.

0b — The ISP1507 will not invert the FAULT signal (default).

1b — The ISP1507 will invert the FAULT signal.

4 - reserved

3 CLOCK_SUSPENDM Clock Suspend LOW: Active LOW clock suspend.

Powers down the internal clock circuitry only. By default, the clock will not be powered in

6-pin serial mode or 3-pin serial mode.

Valid only in 6-pin serial mode and 3-pin serial mode. Valid only when SUSPENDM is set to

logic 1, otherwise this bit is ignored.

0b — Clock will not be powered in 3-pin or 6-pin serial mode (default).

1b — Clock will be powered in 3-pin and 6-pin serial mode.

2 - reserved

1 3PIN_FSLS_SERIAL 3-Pin Full-Speed Low-Speed Serial Mode: Changes the ULPI interface to a 3-bit serial

interface. The PHY will automatically clear this bit when 3-pin serial mode is exited.

0b — Full-speed or low-speed packets are sent using the parallel interface (default).

1b — Full-speed or low-speed packets are sent using the 3-pin serial interface.

0 6PIN_FSLS_SERIAL 6-Pin Full-Speed Low-Speed Serial Mode: Changes the ULPI interface to a 6-bit serial

interface. The PHY will automatically clear this bit when 6-pin serial mode is exited.

0b — Full-speed or low-speed packets are sent using the parallel interface (default).

1b — Full-speed or low-speed packets are sent using the 6-pin serial interface.

Product data sheet Rev. 03 — 22 October 2009 53 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Table 29. OTG_CTRL - OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol USE_EXT_

VBUS_IND

DRV_

VBUS_EXT

DRV_

VBUS

CHRG_

VBUS

DISCHRG_

VBUS

DM_PULL

DOWN

DP_PULL

DOWN

ID_PULL

Reset 00000110

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Table 30. OTG_CTRL - OTG Control register (address R = 0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit

description

Bit Symbol Description

7 USE_EXT_VBUS_

IND

Use External VBUS Indicator: Informs the PHY to use an external VBUS overcurrent indicator.

0b — Use the internal OTG comparator (default).

1b — Use the external VBUS valid indicator signal input from the FAULT pin.

6 DRV_VBUS_EXT Drive VBUS External: Selects between the internal and external 5 V VBUS supply. Using an

external charge pump or a 5 V supply is optional.

0b — Drive VBUS using the internal charge pump. Also ensures PSW_N is not driven to LOW

(default).

1b — Drive VBUS using the external charge pump or the 5 V supply. Drives PSW_N to LOW.

5 DRV_VBUS Drive VBUS: Signals the ISP1507 to drive 5 V on VBUS. If DRV_VBUS_EXT is set to logic 1,

then setting DRV_VBUS is optional.

0b — Do not drive VBUS (default).

1b — Drive 5 V on VBUS.

4 CHRG_VBUS Charge VBUS: Charges VBUS through a resistor. Used for the VBUS pulsing SRP. The link must

first check that VBUS is discharged (see bit DISCHRG_VBUS), and that both the DP and DM

data lines have been LOW (SE0) for 2 ms.

0b — Do not charge VBUS (default).

1b — Charge VBUS.

3 DISCHRG_VBUS Discharge VBUS: Discharges VBUS through a resistor. If the link sets this bit to logic 1, it waits

for an RXCMD indicating that SESS_END has changed from 0 to 1, and then resets this bit to

0 to stop the discharge.

0b — Do not discharge VBUS (default).

1b — Discharge VBUS.

2 DM_PULLDOWN DM Pull Down: Enables the 15 kΩ pull-down resistor on DM.

0b — Pull-down resistor is not connected to DM.

1b — Pull-down resistor is connected to DM (default).

1 DP_PULLDOWN DP Pull Down: Enables the 15 kΩ pull-down resistor on DP.

0b — Pull-down resistor is not connected to DP.

1b — Pull-down resistor is connected to DP (default).

0 ID_PULLUP ID Pull Up: Connects a pull-up to the ID line and enables sampling of the ID level. Disabling

the ID line sampler will reduce PHY power consumption.

0b — Disables sampling of the ID line (default).

1b — Enables sampling of the ID line.

Product data sheet Rev. 03 — 22 October 2009 54 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

10.1.5 USB_INTR_EN_R_E register

The bits in this register enable interrupts and RXCMDs to be sent when the corresponding

bits in the USB_INTR_STAT register change from logic 0 to logic 1. By default, all

transitions are enabled. Tab le 3 1 shows the bit allocation of the register.

10.1.6 USB_INTR_EN_F_E register

The bits in this register enable interrupts and RXCMDs to be sent when the corresponding

bits in the USB_INTR_STAT register change from logic 1 to logic 0. By default, all

transitions are enabled. See Tabl e 33 .

Table 31. USB_INTR_EN_R_E - USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh,

S = 0Eh, C = 0Fh) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved ID_GND_R SESS_

END_R

SESS_

VALID_R

VBUS_

VALID_R

HOST_

DISCON_R

Reset 00011111

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Table 32. USB_INTR_EN_R_E - USB Interrupt Enable Rising Edge register (address R = 0Dh to 0Fh, W = 0Dh,

S = 0Eh, C = 0Fh) bit description

Bit Symbol Description

7to5 - reserved

4 ID_GND_R ID Ground Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on ID_GND.

3 SESS_END_R Session End Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

SESS_END.

2 SESS_VALID_R Session Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

SESS_VLD.

1 VBUS_VALID_R VBUS Valid Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

A_VBUS_VLD.

0 HOST_DISCON_

Host Disconnect Rise: Enables interrupts and RXCMDs for logic 0 to logic 1 transitions on

HOST_DISCON.

Table 33. USB_INTR_EN_F_E - USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h,

S = 11h, C = 12h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved ID_GND_F SESS_

END_F

SESS_

VALID_F

VBUS_

VALID_F

HOST_

DISCON_F

Reset 00011111

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Table 34. USB_INTR_EN_F_E - USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h,

S = 11h, C = 12h) bit description

Bit Symbol Description

7to5 - reserved

4 ID_GND_F ID Ground Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on ID_GND.

3 SESS_END_F Session End Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

SESS_END.

Product data sheet Rev. 03 — 22 October 2009 55 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

10.1.7 USB_INTR_STAT register

This register (see Tabl e 3 5 ) indicates the current value of the interrupt source signal.

10.1.8 USB_INTR_L register

The bits of the USB_INTR_L register are automatically set by the ISP1507 when an

unmasked change occurs on the corresponding interrupt source signal. The ISP1507 will

automatically clear all bits when the link reads this register, or when the PHY enters

low-power or serial mode.

Remark: It is optional for the link to read this register when the clock is running because

all signal information will automatically be sent to the link through the RXCMD byte.

The bit allocation of this register is given in Tab le 37 .

2 SESS_VALID_F Session Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

SESS_VLD.

1 VBUS_VALID_F VBUS Valid Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

A_VBUS_VLD.

0 HOST_DISCON

Host Disconnect Fall: Enables interrupts and RXCMDs for logic 1 to logic 0 transitions on

HOST_DISCON.

Table 34. USB_INTR_EN_F_E - USB Interrupt Enable Falling Edge register (address R = 10h to 12h, W = 10h,

S = 11h, C = 12h) bit description …continued

Bit Symbol Description

Table 35. USB_INTR_STAT - USB Interrupt Status register (address R = 13h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved ID_GND SESS_END SESS_

VALID

VBUS_

VALID

HOST_

DISCON

Reset XXX00000

Access RRRRRRRR

Table 36. USB_INTR_STAT - USB Interrupt Status register (address R = 13h) bit description

Bit Symbol Description

7to5 - reserved

4ID_GND ID Ground: Reflects the current value of the ID detector circuit.

3 SESS_END Session End: Reflects the current value of the session end voltage comparator.

2 SESS_VALID Session Valid: Reflects the current value of the session valid voltage comparator.

1 VBUS_VALID VBUS Valid: Reflects the current value of the VBUS valid voltage comparator.

0 HOST_DISCON Host Disconnect: Reflects the current value of the host disconnect detector.

Table 37. USB_INTR_L - USB Interrupt Latch register (address R = 14h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved ID_GND_L SESS_

END_L

SESS_

VALID_L

VBUS_

VALID_L

HOST_

DISCON_L

Reset 00000000

Access RRRRRRRR

Product data sheet Rev. 03 — 22 October 2009 56 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

10.1.9 DEBUG register

The bit allocation of the DEBUG register is given in Tab le 3 9 . This register indicates the

current value of signals useful for debugging.

10.1.10 SCRATCH register

This is an empty register for testing purposes; see Tabl e 4 1 .

10.1.11 Reserved

Registers 19h to 2Eh are not implemented. Operating on these addresses will have no

effect on the PHY.

10.1.12 Access extended register set

Address 2Fh does not contain register data. Instead it links to the extended register set.

The immediate register set maps to the lower end of the extended register set.

Table 38. USB_INTR_L - USB Interrupt Latch register (address R = 14h) bit description

Bit Symbol Description

7to5 - reserved

4ID_GND_L ID Ground Latch: Automatically set when an unmasked event occurs on ID_GND. Cleared

when this register is read.

3 SESS_END_L Session End Latch: Automatically set when an unmasked event occurs on SESS_END.

Cleared when this register is read.

2 SESS_VALID_L Session Valid Latch: Automatically set when an unmasked event occurs on SESS_VLD.

Cleared when this register is read.

1 VBUS_VALID_L VBUS Valid Latch: Automatically set when an unmasked event occurs on A_VBUS_VLD.

Cleared when this register is read.

0 HOST_DISCON_L Host Disconnect Latch: Automatically set when an unmasked event occurs on

HOST_DISCON. Cleared when this register is read.

Table 39. DEBUG - Debug register (address R = 15h) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved LINE

STATE1

LINE

STATE0

Reset 00000000

Access RRRRRRRR

Table 40. DEBUG - Debug register (address R = 15h) bit description

Bit Symbol Description

7to2 - reserved

1 LINESTATE1 Line State 1: Contains the current value of LINESTATE 1.

0 LINESTATE0 Line State 0: Contains the current value of LINESTATE 0.

Table 41. SCRATCH - Scratch register (address R = 16h to 18h, W = 16h, S = 17h, C = 18h) bit description

Legend: * reset value

Bit Symbol Access Value Description

7to0 SCRATCH

[7:0]

R/W/S/C 00h* Scratch: This is an empty register byte for testing purposes. Software can read,

write, set and clear this register. The functionality of the PHY will not be affected.

Product data sheet Rev. 03 — 22 October 2009 57 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

10.1.13 Vendor-specific registers

Addresses 30h to 3Fh contain vendor-specific registers.

10.1.14 PWR_CTRL register

This register controls various aspects of the ISP1507. See Tab le 4 2 .

10.2 Extended register set

Addresses 00h to 3Fh of the extended register set directly map to the immediate set. This

means a read, write, set or clear operation to these extended addresses will operate on

the immediate register set.

Addresses 40h to FFh are not implemented. Operating on these addresses may result in

undefined behavior of the PHY.

Table 42. PWR_CTRL - Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit allocation

Bit 7 6 5 4 3 2 1 0

Symbol reserved BVALID_

FALL

BVALID_

RISE

reserved

Reset 00000000

Access R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C R/W/S/C

Table 43. PWR_CTRL - Power Control register (address R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit description

Bit Symbol Description

7 to 4 - reserved; the link must never write logic 1 to these bits.

3 BVALID_FALL BVALID Fall: Enables RXCMDs for HIGH-to-LOW transitions on BVALID. When BVALID

changes from HIGH to LOW, the ISP1507 will send an RXCMD to the link with the ALT_INT bit

set to logic 1.

This bit is optional and is not necessary for OTG devices. This bit is provided for debugging

purposes. The session valid comparator should be used instead.

2 BVALID_RISE BVALID Rise: Enables RXCMDs for LOW-to-HIGH transitions on BVALID. When BVALID

changes from LOW to HIGH, the ISP1507 will send an RXCMD to the link with the ALT_INT bit

set to logic 1.

This bit is optional and is not necessary for OTG devices. This bit is provided for debugging

purposes. The session valid comparator should be used instead.

1 to 0 - reserved; the link must never write logic 1 to these bits.

Product data sheet Rev. 03 — 22 October 2009 58 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

11. ElectroStatic Discharge (ESD)

11.1 ESD protection

The pins that are connected to the USB connector (DP, DM, ID, VBUS and GND) have a

minimum of ±4 kV ESD protection. Capacitors 0.1 μF and 1 μF must be connected in

parallel from VBUS to GND to achieve this ±4 kV ESD protection (see Figure 24).

Remark: Capacitors 0.1 μF and 1 μF are also required by Universal Serial Bus

Specification Rev. 2.0. For details on the requirements for CVBUS, see Section 16.

11.2 ESD test conditions

A detailed report on test setup and results is available on request.

Fig 24. Human body ESD test model

1500 Ω

1 MΩ

HIGH VOLTAGE

DC SOURCE 0.1 μF1 μF

VBUS

DEVICE UNDER

TEST

100 pF storage

capacitor

charge current

limit resistor discharge

resistance

GND

004aaa881

Product data sheet Rev. 03 — 22 October 2009 59 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

12. Limiting values

[1] Maximum value may not exceed 4.6 V.

[2] Includes voltage on outputs in 3-state mode.

[3] Only valid when the VCC(I/O) supply voltage is present.

[4] The ISP1507 has been tested according to the additional requirements listed in Universal Serial Bus Specification Rev. 2.0,

Section 7.1.1. The short circuit withstand test and the AC stress test were performed for 24 hours, and the ISP1507 was found to be

fully operational after the test completed.

[5] Equivalent to discharging a 100 pF capacitor through a 1.5 kΩ resistor (Human Body Model JESD22-A114D).

13. Recommended operating conditions

[1] VCC(I/O) must be less than or equal to VCC.

Table 44. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VCC supply voltage −0.5 +4.6 V

VCC(I/O) input/output supply voltage −0.5 +4.6 V

VIinput voltage on pins STP, DATA[7:0],

RESET_N and CHIP_SELECT_N

−0.5 VCC(I/O) +0.5

[1][2][3] V

on pins VBUS, FAULT and PSW_N −0.5 +6.0 V

on pin XTAL1 −0.5 +2.5 V

on pin ID −0.5 +4.6 V

on pins DP and DM [4] −0.5 +4.6 V

VESD electrostatic discharge

voltage

pins DP, DM, ID, VBUS and GND;

ILI < 1 μA

[5] −4+4 kV

all other pins; ILI < 1 μA[5] −1.5 +1.5 kV

Ilu latch-up current −0.5 ×VCC <V<+1.5×VCC - 100 mA

Tstg storage temperature −40 +125 °C

Table 45. Recommended operating conditions

Symbol Parameter Conditions Min Typ Max Unit

VCC supply voltage 3.0 3.3 3.6 V

VCC(I/O) input/output supply voltage [1] 1.65 - 3.6 V

VIinput voltage on pins STP, DATA[7:0], RESET_N

and CHIP_SELECT_N

0- V

CC(I/O) V

on pins VBUS, FAULT and PSW_N 0 - 5.5 V

on pins DP, DM and ID 0 - 3.6 V

on pin XTAL1 0 - 1.95 V

Tamb ambient temperature −40 +25 +85 °C

Tjjunction temperature −40 - +125 °C

Product data sheet Rev. 03 — 22 October 2009 60 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

14. Static characteristics

[1] A continuous stream of 1 kB packets with minimum inter-packet gap and all data bits set to logic 0 for continuous toggling.

Table 46. Static characteristics: supply pins

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

V(REG3V3) voltage on pin REG3V3 3.0 3.3 3.6 V

V(REG1V8) voltage on pin REG1V8 1.65 1.8 1.95 V

VPOR(trip) power-on reset trip voltage 1.0 - 1.5 V

ICC supply current charge pump disabled

low-power mode; VBUS valid detector

disabled; 1.5 kΩ pull-up resistor on

pin DP disconnected

-3585μA

low-power mode; VBUS valid detector

disabled; 1.5 kΩ pull-up resistor on

pin DP connected

- 215 280 μA

full-speed continuous data transmit;

50 pF load on pins DP and DM

[1] -15-mA

full-speed continuous data receive [1] -11-mA

high-speed continuous data transmit;

45 Ω load on pins DP and DM to ground

[1] -48-mA

high-speed continuous data receive [1] -28-mA

charge pump enabled

IO(VBUS) = 8 mA; charge pump supply

current only

-2023mA

IO(VBUS) = 0 mA; charge pump supply

current only

- 300 - μA

ICC(I/O)(stat) static supply current on

pin VCC(I/O)

power-down mode (chip select is

non-active)

-10-μA

ICC(I/O) supply current on

pin VCC(I/O)

ULPI interface pins are static - - 1 μA

Table 47. Static characteristics: digital pins

Digital pins: CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N and CHIP_SELECT_N; unless otherwise specified.

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Input levels

VIL LOW-level input voltage - - 0.3 ×VCC(I/O) V

VIH HIGH-level input voltage 0.7 ×VCC(I/O) -- V

IIL LOW-level input current VI= 0 V - - 1 μA

IIH HIGH-level input current VI= VCC(I/O) --1μA

ILI input leakage current −1+0.1+1 μA

Output levels

VOH HIGH-level output voltage IOH = −4mA V

CC(I/O) −0.4 - - V

Product data sheet Rev. 03 — 22 October 2009 61 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

VOL LOW-level output voltage IOL = +4 mA - - 0.4 V

IOH HIGH-level output current VO= VCC(I/O) −0.4 V −4- - mA

IOL LOW-level output current VO= 0.4 V +4 - - mA

IOZ off-state output current 0 V < VO<V

CC(I/O) --1μA

Impedance

ZLload impedance 45 - 65 Ω

Pull-up and pull-down

Ipd pull-down current interface protect enabled;

DATA[7:0] pins only;

VI=V

CC(I/O)

25 50 90 μA

Ipu pull-up current interface protect enabled;

STP pin only; VI=0V

−30 −50 −80 μA

Capacitance

Cin input capacitance pins STP, RESET_N,

DATA[7:0],

CHIP_SELECT_N

--3.5pF

Table 47. Static characteristics: digital pins …continued

Digital pins: CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N and CHIP_SELECT_N; unless otherwise specified.

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Table 48. Static characteristics: digital pin FAULT

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Input levels

VIL LOW-level input voltage - - 0.8 V

VIH HIGH-level input voltage 2.0 - - V

IIL LOW-level input current VI= 0 V - - 1 μA

IIH HIGH-level input current VI= VCC(I/O) -- 1μA

Table 49. Static characteristics: digital pin PSW_N

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Output levels

VOH HIGH-level output voltage external pull-up resistor connected - - 5.5 V

VOL LOW-level output voltage IOL = −4mA - - 0.4 V

IOH HIGH-level output current external pull-up resistor connected - - 1 μA

IOL LOW-level output current VO= 0.4 V 4.0 - - mA

Product data sheet Rev. 03 — 22 October 2009 62 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Table 50. Static characteristics: analog I/O pins (DP, DM)

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Original USB transceiver (low-speed and full-speed)

Input levels (differential receiver)

VDI differential input sensitivity voltage |VDP −VDM|0.2--V

VCM differential common mode voltage

range

includes VDI range 0.8 - 2.5 V

Input levels (single-ended receivers)

VIL LOW-level input voltage - - 0.8 V

VIH HIGH-level input voltage 2.0 - - V

Output levels

VOL LOW-level output voltage pull-up on pin DP;

RL= 1.5 kΩ to 3.6 V

0.0 0.18 0.3 V

VOH HIGH-level output voltage pull-down on

pins DP and DM;

RL= 15 kΩ to GND

2.8 3.2 3.6 V

Termination

VTERM termination voltage for upstream

facing port pull-up

for 1.5 kΩ pull-up

resistor

3.0 - 3.6 V

Resistance

RUP(DP) pull-up resistance on pin DP 1425 1500 1575 Ω

High-speed USB transceiver

Input levels (differential receiver)

VHSSQ high-speed squelch detection

threshold voltage (differential signal

amplitude)

100 - 150 mV

VHSDSC high-speed disconnect detection

threshold voltage (differential signal

amplitude)

525 - 625 mV

VHSDI high-speed differential input sensitivity |VDP −VDM|100--mV

VHSCM high-speed data signaling common

mode voltage range (guideline for

receiver)

includes VDI range −50 - +500 mV

VHSOI high-speed idle level voltage −10 - +10 mV

VHSOL high-speed data signaling LOW-level

voltage

−10 - +10 mV

Output levels

VHSOH high-speed data signaling HIGH-level

voltage

360 - 440 mV

VCHIRPJ Chirp J level (differential voltage) 700 - 1100 mV

VCHIRPK Chirp K level (differential voltage) −900 - −500 mV

Leakage current

ILZ off-state leakage current −1- +1 μA

Capacitance

Cin input capacitance pin to GND - - 5 pF

Product data sheet Rev. 03 — 22 October 2009 63 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

[1] For high-speed USB and full-speed USB.

Resistance

RDN(DP) pull-down resistance on pin DP 14.25 15 15.75 kΩ

RDN(DM) pull-down resistance on pin DM 14.25 15 15.75 kΩ

Termination

ZO(drv)(DP) driver output impedance on pin DP steady-state drive [1] 40.5 45 49.5 Ω

ZO(drv)(DM) driver output impedance on pin DM steady-state drive [1] 40.5 45 49.5 Ω

ZINP input impedance exclusive of

pull-up/pull-down (for low-/full-speed)

10--MΩ

Table 50. Static characteristics: analog I/O pins (DP, DM) …continued

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Table 51. Static characteristics: charge pump

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Voltage

VO(VBUS) output voltage on pin VBUS IO(VBUS) = 50 mA;

Ccp(C_A)-(C_B) = 270 nF

4.65 5.0 5.25 V

VL(VBUS) leakage voltage on pin VBUS charge pump disabled - - 0.2 V

Current

IO(VBUS) output current on pin VBUS Ccp(C_A)-(C_B) = 270 nF 45 75 - mA

Efficiency

ηcp charge pump efficiency IO(VBUS) = 50 mA 60 72 78 %

Table 52. Static characteristics: VBUS comparators

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

VA_VBUS_VLD A-device VBUS valid voltage 4.4 4.5 4.65 V

VB_SESS_VLD B-device session valid voltage for A-device and

B-device

0.8 1.6 2.0 V

Vhys(B_SESS_VLD) B-device session valid hysteresis voltage 70 90 110 mV

VB_SESS_END B-device session end voltage 0.2 0.5 0.8 V

Product data sheet Rev. 03 — 22 October 2009 64 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Table 53. Static characteristics: VBUS resistors

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

RUP(VBUS) pull-up resistance on pin VBUS connect to pin REG3V3

when CHRG_VBUS is

logic 1

281 680 - Ω

RDN(VBUS) pull-down resistance on pin VBUS connect to GND when

DISCHRG_VBUS is

logic 1

656 1100 - Ω

RI(idle)(VBUS)(A) idle input resistance on pin VBUS

(A-device)

ID pin LOW and charge

pump disabled

40 57 80 kΩ

RI(idle)(VBUS)(B) idle input resistance on pin VBUS

(B-device)

ID pin HIGH or charge

pump enabled

170 240 310 kΩ

Table 54. Static characteristics: ID detection circuit

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

tID ID detection time 50 - - ms

Vth(ID) ID detector threshold voltage 0.8 1.2 2.0 V

RUP(ID) ID pull-up resistance ID_PULLUP is logic 1 40 50 60 kΩ

Table 55. Static characteristics: resistor reference

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

VO(RREF) output voltage on pin RREF SUSPENDM is logic 1 - 1.22 - V

Product data sheet Rev. 03 — 22 October 2009 65 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

ICC(cp) denotes charge pump supply current.

Fig 25. Charge pump supply current as a function of

VBUS output current

Fig 26. VBUS output voltage as a function of VBUS

output current

VCC(cp) denotes charge pump supply voltage. ICC(cp) denotes charge pump supply current.

Fig 27. VBUS output voltage as a function of charge

pump supply voltage

Fig 28. Charge pump supply current as a function of

temperature

004aaa876

100

120

0 1020304050

VCC = 3.6 V

3.3 V

3.0 V

CC(cp)

(mA)

O(VBUS)

(mA)

004aaa877

4.00

4.50

5.00

5.50

01020304050

VCC = 3.6 V

3.3 V

3.0 V

O(VBUS)

(V)

O(VBUS)

(mA)

004aaa878

4.00

4.50

5.00

5.50

3 3.1 3.2 3.3 3.4 3.5 3.6

IO(VBUS) = 0 mA

8 mA

50 mA

O(VBUS)

(V)

CC(cp)

(V)

004aaa879

100

102

104

106

108

−40 −20 0 +20 +40 +60 +80 +100

IO(VBUS) = 50 mA

amb

(°C)

CC(cp)

(mA)

Product data sheet Rev. 03 — 22 October 2009 66 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

15. Dynamic characteristics

[1] The internal PLL is triggered only on the positive edge from the crystal oscillator. Therefore, the duty cycle is not critical.

Table 56. Dynamic characteristics: reset and clock

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Reset

tW(POR) internal power-on reset pulse

width

0.2 - - μs

tw(REG1V8_H) REG1V8 HIGH pulse width 2 - - μs

tw(REG1V8_L) REG1V8 LOW pulse width 11 - - μs

tW(RESET_N) external RESET_N pulse width 200 - - ns

tREGUP regulator start-up time 4.7 μF±20 % capacitor each on

pins REG1V8 and REG3V3

VCC =3.3V; T

amb = +25 °C-2-ms

VCC =3.0V; T

amb = −40 °C--50ms

Crystal or clock applied to XTAL1

fi(XTAL1) input frequency on pin XTAL1 ISP1507A - 19.2 - MHz

ISP1507B - 26 - MHz

tjit(i)(XTAL1)RMS RMS input jitter on pin XTAL1 ISP1507A - - 200 ps

ISP1507B - - 300 ps

δi(XTAL1) input duty cycle on pin XTAL1 applicable only when clock is

applied on pin XTAL1

[1] -50-%

Δfi(XTAL1) input frequency tolerance on

pin XTAL1

- 50 200 ppm

tr(XTAL1) rise time on pin XTAL1 only for square wave input - - 5 ns

tf(XTAL1) fall time on pin XTAL1 only for square wave input - - 5 ns

V(XTAL1)(p-p) peak-to-peak voltage on

pin XTAL1

only for square wave input 0.566 - 1.95 V

Output CLOCK characteristics

fo(CLOCK) output frequency on

pin CLOCK

-60-MHz

tjit(o)(CLOCK)RMS RMS output jitter on pin

CLOCK

--500ps

δo(CLOCK) output clock duty cycle on

pin CLOCK

45 50 55 %

tstartup(PLL) PLL startup time - 650 - μs

tstartup(o)(CLOCK) output CLOCK start-up time measured from power good or

assertion of pin STP

450 650 900 μs

Product data sheet Rev. 03 — 22 October 2009 67 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Table 57. Dynamic characteristics: digital I/O pins

VCC = 3.0 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

VCC(I/O) = 1.65 V to 1.95 V

tsu(DATA) DATA set-up time with respect to

the rising edge of pin CLOCK

20 pF total external load

per pin

5.7 - - ns

th(DATA) DATA hold time with respect to

the rising edge of pin CLOCK

20 pF total external load

per pin

0- - ns

td(DATA) DATA output delay with respect

to the rising edge of pin CLOCK

20 pF total external load

per pin

--7.8ns

tsu(STP) STP set-up time with respect to

the rising edge of pin CLOCK

20 pF total external load

per pin

4.5 - - ns

th(STP) STP hold time with respect to

the rising edge of pin CLOCK

20 pF total external load

per pin

0- - ns

td(DIR) DIR output delay with respect to

the rising edge of pin CLOCK

20 pF total external load

per pin

--8.9ns

td(NXT) NXT output delay with respect to

the rising edge of pin CLOCK

20 pF total external load

per pin

--8.9ns

VCC(I/O) =3.0Vto3.6V

tsu(DATA) DATA set-up time with respect to

the rising edge of pin CLOCK

30 pF total external load

per pin

3.3 - - ns

th(DATA) DATA hold time with respect to

the rising edge of pin CLOCK

30 pF total external load

per pin

0.8 - - ns

td(DATA) DATA output delay with respect

to the rising edge of pin CLOCK

30 pF total external load

per pin

--5.5ns

tsu(STP) STP set-up time with respect to

the rising edge of pin CLOCK

30 pF total external load

per pin

3.4 - - ns

th(STP) STP hold time with respect to

the rising edge of pin CLOCK

30 pF total external load

per pin

0.8 - - ns

td(DIR) DIR output delay with respect to

the rising edge of pin CLOCK

30 pF total external load

per pin

--6.6ns

td(NXT) NXT output delay with respect to

the rising edge of pin CLOCK

30 pF total external load

per pin

--6.6ns

Table 58. Dynamic characteristics: analog I/O pins (DP and DM)

VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb =

−

C to +85

C; unless otherwise specified.

Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

High-speed driver

tHSR rise time (10 % to 90 %) 500 - - ps

tHSF fall time (10 % to 90 %) 500 - - ps

Full-speed driver

tFR rise time CL= 50 pF; 10 % to 90 % of

|VOH −VOL|

4- 20ns

tFF fall time CL= 50 pF; 10 % to 90 % of

|VOH −VOL|

4- 20ns

tFRFM differential rise and fall

time matching

excluding the first transition

from the idle state

90 - 111.1 %

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  68 of 82
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
VCRS output signal crossover 
voltage
excluding the first transition 
from the idle state
1.3 - 2.0 V
Low-speed driver
tLR transition time: rise time CL= 200 pF to 600 pF; 
1.5 kΩ pull-up on pin DM 
enabled; 10 % to 90 % of 
|VOH −VOL|
75 - 300 ns
tLF transition time: fall time CL= 200 pF to 600 pF; 
1.5 kΩ pull-up on pin DM 
enabled; 10 % to 90 % of 
|VOH −VOL|
75 - 300 ns
tLRFM rise and fall time matching tLR/tLF; excluding the first 
transition from the idle state
80 - 125 %
Driver timing
tPLH(drv) driver propagation delay 
(LOW to HIGH)
TX_DAT, TX_SE0 to DP, DM; 
see Figure 30
--20ns
tPHL(drv) driver propagation delay 
(HIGH to LOW)
TX_DAT, TX_SE0 to DP, DM; 
see Figure 30
--20ns
tPHZ driver disable delay from 
HIGH level
TX_ENABLE to DP, DM; 
see Figure 31
--12ns
tPLZ driver disable delay from 
LOW level
TX_ENABLE to DP, DM; 
see Figure 31
--12ns
tPZH driver enable delay to 
HIGH level
TX_ENABLE to DP, DM; 
see Figure 31
--20ns
tPZL driver enable delay to 
LOW level
TX_ENABLE to DP, DM; 
see Figure 31
--20ns
Receiver timing
Differential receiver
tPLH(rcv) receiver propagation 
delay (LOW to HIGH)
DP, DM to RX_RCV, RX_DP 
and RX_DM; see Figure 32
--20ns
tPHL(rcv) receiver propagation 
delay (HIGH to LOW)
DP, DM to RX_RCV, RX_DP 
and RX_DM; see Figure 32
--20ns
Single-ended receiver
tPLH(se) single-ended propagation 
delay (LOW to HIGH)
DP, DM to RX_RCV, RX_DP 
and RX_DM; see Figure 32
--20ns
tPHL(se) single-ended propagation 
delay (HIGH to LOW)
DP, DM to RX_RCV, RX_DP 
and RX_DM; see Figure 32
--20ns
Table 58. Dynamic characteristics: analog I/O pins (DP and DM) …continued
VCC = 3.0 V to 3.6 V; VCC(I/O) = 1.65 V to 3.6 V; Tamb = 
−
40
°
C to +85
°
C; unless otherwise specified.
Typical values are at VCC = 3.3 V; VCC(I/O) = 3.3 V; Tamb = +25
°
C; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 03 — 22 October 2009 69 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

15.1 ULPI timing

ULPI interface timing requirements are given in Figure 33. This timing applies to

synchronous mode only. All timing is measured with respect to the ISP1507 CLOCK pin.

All signals are clocked on the rising edge of CLOCK.

Fig 29. Rise time and fall time Fig 30. Timing of TX_DAT and TX_SE0 to DP and DM

Fig 31. Timing of TX_ENABLE to DP and DM Fig 32. Timing of DP and DM to RX_RCV, RX_DP and

RX_DM

004aaa861

VOL

tHSR, tFR, tLR tHSF, tFF, tLF

VOH 90 %

10 % 10 %

90 %

004aaa573

VOL

VOH

tPHL(drv)

tPLH(drv)

VCRS VCRS

0.9 V

1.8 V

0 V

logic input

differential

data lines

004aaa574

PZH

PZL

PHZ

PLZ

− 0.3 V

+ 0.3 V

CRS

0.9 V

1.8 V

0 V

logic

input

differential

data lines

tPLH(se) tPHL(se)

004aaa575

VOL

VOH

tPHL(rcv)

tPLH(rcv)

VCRS VCRS

0.9 V

2.0 V

0.8 V

logic output

differential

data lines

Fig 33. ULPI interface timing

CLOCK

CONTROL IN

(STP)

DATA IN

(8-BIT)

tsu(STP) th(STP)

tsu(DATA) th(DATA)

CONTROL OUT

(DIR, NXT)

DATA OUT

(8-BIT) 004aaa722

td(DIR),

td(NXT)

td(DATA) td(DIR),

td(NXT)

Product data sheet Rev. 03 — 22 October 2009 70 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

16. Application information

[1] For detailed information and alternative interface options, refer to the Interfacing to the ISP1507 (AN10080) application note.

[2] For more information, contact Murata.

Remark: In the following application diagrams, because the ULPI bus is not shared, the

CHIP_SELECT_N pin is connected to ground. In other applications, CHIP_SELECT_N

can be controlled by a link to 3-state the ULPI bus so that those pins can be used for other

purposes.

Table 59. Recommended bill of materials

Designator[1] Application Value Comment

Cbypass highly recommended for all

applications

0.1 μF-

Ccp(C_A)-(C_B) charge pump is used 22 nF (8 mA), 270 nF (50 mA);

up to 470nF (50mA)

Cfilter highly recommended for all

applications

4.7 μF±20 %; use a LOW

ESR capacitor (0.2 Ω to 2 Ω)

for best performance

CVBUS mandatory for peripherals 0.1 μF and 1 μFto10μF in

parallel

mandatory for host 0.1 μF and 120 μF±20 %

(min) in parallel

mandatory for OTG 0.1 μF and 1 μFto6.5μF in

parallel

Rpullup recommended; for

applications with an

external VBUS supply

controlled by PSW_N

4.7 kΩ (recommended) maximum value is determined by the voltage

drop on PSW_N caused by leakage into

PSW_N and the external supply control pin

RRREF mandatory in all

applications

12 kΩ±1% -

RVBUS strongly recommended for

peripheral or external 5 V

applications only

1kΩ±5% -

RXTAL required only for

applications driving a

square wave into the XTAL1

47 kΩ±5 % used to avoid floating input on the XTAL1 pin

XTAL crystal is used 19.2 MHz CL=10pF; R

S<220Ω; CXTAL =18pF

26 MHz CL=10pF; R

S<130Ω; CXTAL =18pF

CSTCE26M0XK2***-R0[2] CXTAL is not required

C(XTAL)SQ required only for

applications driving a

square wave into the XTAL1

pin that has a DC offset

100 pF used to AC couple the input square wave to

the XTAL1 pin

DVBUS recommended for all OTG

applications

- STPS0520Z; Schottky rectifier

Remark: Adding Schottky diode will bring

down the VBUS voltage by 0.2 V to 0.25 V,

depending on the load current. However, it is

still within the requirement of Universal Serial

Bus Specification Rev. 2.0.

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 03 — 22 October 2009 71 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

(1) Frequency is version dependent: ISP1507A: 19.2 MHz; ISP1507B: 26 MHz.

Fig 34. Using the ISP1507 with an OTG controller; internal charge pump is utilized and crystal is attached

ISP1507

DATA0

VCC(I/O)

RREF

FAULT

CPGND

C_B

C_A

VCC

PSW_N

DATA1

DATA2

VCC(I/O)

CHIP_

SELECT_N

DATA3

CLOCK

DATA4

DATA5

DATA6

DATA7

VCC(I/O)

NXT

004aab040

VBUS

REG3V3

XTAL1

XTAL2 16

13 STP

DIR

REG1V8

RESET_N

OTG

CONTROLLER

1DATA0

DATA1

DATA2

DATA3

DATA4

DATA5

DATA6

DATA7

CLOCK

NXT

STP

DIR

VCC(I/O)

VCC

Cbypass RRREF

CVBUS

Cbypass

CXTAL

XTAL(1)

GND (die pad)

CXTAL Cbypass

Cfilter

Ccp(C_A)-(C_B)

VBUS

D−

D+

GND

USB

MICRO-AB

RECEPTACLE

SHIELD

Cbypass

RVBUS

DVBUS

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 03 — 22 October 2009 72 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

(1) Frequency is version dependent: ISP1507A: 19.2 MHz; ISP1507B: 26 MHz.

Fig 35. Using the ISP1507 with a standard USB host controller; external 5 V source with built-in FAULT and external square wave input on XTAL1

ISP1507

DATA0

CC(I/O)

RREF

FAULT

CPGND

C_B

C_A

PSW_N

DATA1

DATA2

CC(I/O)

CHIP_SELECT_N

DATA3

CLOCK

DATA4

DATA5

DATA6

DATA7

CC(I/O)

NXT

004aab041

BUS

REG3V3

XTAL1

XTAL2 16

13 STP

DIR

REG1V8

RESET_N

HOST

CONTROLLER

USB

STANDARD-A

RECEPTACLE

BUS

D−

D+

GND

1DATA0

DATA1

DATA2

DATA3

DATA4

DATA5

DATA6

DATA7

CLOCK

NXT

STP

DIR

CC(I/O)

GND (die pad)

IN FAULT

ON OUT

BUS

SWITCH

Rpullup

Cbypass

RRREF

CVBUS

Cbypass Cfilter

SHIELD

+5 V

C(XTAL)SQ

i(XTAL1)(1) RXTAL

Cbypass

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 03 — 22 October 2009 73 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

(1) Frequency is version dependent: ISP1507A: 19.2 MHz; ISP1507B: 26 MHz.

Fig 36. Using the ISP1507 with a standard USB peripheral controller; external crystal

ISP1507

DATA0

VCC(I/O)

RREF

FAULT

CPGND

C_B

C_A

VCC

PSW_N

DATA1

DATA2

VCC(I/O)

CHIP_SELECT_N

DATA3

CLOCK

DATA4

DATA5

DATA6

DATA7

VCC(I/O)

NXT

004aab042

VBUS

REG3V3

XTAL1

XTAL2 16

13 STP

DIR

REG1V8

RESET_N

PERIPHERAL

CONTROLLER

USB

STANDARD-B

RECEPTACLE

VBUS

D−

D+

GND

1DATA0

DATA1

DATA2

DATA3

DATA4

DATA5

DATA6

DATA7

CLOCK

NXT

STP

DIR

VCC(I/O)

VCC

GND (die pad)

Cbypass

Cbypass Cfilter

CXTAL CXTAL

Cbypass Cfilter

RRREF

CVBUS

SHIELD

XTAL(1)

RVBUS

Cbypass

Product data sheet Rev. 03 — 22 October 2009 74 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

17. Package outline

Fig 37. Package outline SOT617-1 (HVQFN32)

0.51

A1Eh

UNIT ye

0.2

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

mm 5.1

4.9

3.25

2.95

5.1

4.9 3.25

2.95

3.5

0.30

0.18

0.05

0.00 0.05 0.1

DIMENSIONS (mm are the original dimensions)

SOT617-1 MO-220- - - - - -

0.5

0.3

0.1

0.05

0 2.5 5 mm

scale

SOT617-1

HVQFN32: plastic thermal enhanced very thin quad flat package; no leads;

32 terminals; body 5 x 5 x 0.85 mm

A(1)

max.

AA1c

detail X

y1C

916

32 25

terminal 1

index area

terminal 1

index area

01-08-08

02-10-18

1/2 e

1/2 e AC

E(1)

Note

1. Plastic or metal protrusions of 0.075 mm maximum per side are not included.

D(1)

Product data sheet Rev. 03 — 22 October 2009 75 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

18. Abbreviations

[1] Physical layer containing the USB transceiver. The ISP1507 is a PHY.

19. References

[1] Universal Serial Bus Specification Rev. 2.0

[2] On-The-Go Supplement to the USB 2.0 Specification Rev. 1.3

Table 60. Abbreviations

Acronym Description

ASIC Application-Specific Integrated Circuit

ATX Analog USB Transceiver

CD-RW Compact Disc-ReWritable

EOP End-Of-Packet

ESD ElectroStatic Discharge

ESR Effective Series Resistance

FS Full-Speed

HBM Human Body Model

HNP Host Negotiation Protocol

HS High-Speed

ID Identification

IEC International Electrotechnical Commission

LS Low-Speed

NRZI Non-Return-to-Zero Inverted

OTG On-The-Go

PCB Printed-Circuit Board

PHY Physical Layer[1]

PID Packet Identifier

PLD Programmable Logic Device

PLL Phase-Locked Loop

POR Power-On Reset

RXCMD Receive Command

SE0 Single-Ended Zero

SOF Start-Of-Frame

SRP Session Request Protocol

SYNC Synchronous

TTL Transistor-Transistor Logic

TXCMD Transmit Command

USB Universal Serial Bus

USB-IF USB Implementers Forum

ULPI UTMI+ Low Pin Interface

UTMI USB 2.0 Transceiver Macrocell Interface

UTMI+ USB 2.0 Transceiver Macrocell Interface Plus

Product data sheet Rev. 03 — 22 October 2009 76 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

[3] UTMI+ Low Pin Interface (ULPI) Specification Rev. 1.1

[4] UTMI+ Specification Rev. 1.0

[5] USB 2.0 Transceiver Macrocell Interface (UTMI) Specification Ver. 1.05

[6] Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM)

(JESD22-A114D)

[7] Interfacing to the ISP1507 (AN10080)

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  77 of 82
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
20. Revision history
 
Table 61. Revision history
Document ID Release date Data sheet status Change notice Supersedes
ISP1507A_ISP1507B_3 20091022 Product data sheet - ISP1507A_ISP1507B_2
Modifications: •Rebranded to the ST-Ericsson template.
•Section 2 “Features”: updated.
•Table 1 “Ordering information”: updated.
•Table 2 “Pin description”: updated description for pins FAULT, C_A, C_B, 
CHIP_SELECT_N, REG3V3 and REG1V8.
•Section 7.6.2.1 “VBUS valid comparator”: updated.
•Section 9.3 “Power-up, reset and bus idle sequence”: updated.
•Table 17 “PHY pipeline delays”: added Table note 1.
•Section 10.1.8 “USB_INTR_L register”: updated the first paragraph.
•Table 44 “Limiting values”: updated.
•Table 46 “Static characteristics: supply pins”: updated.
•Table 47 “Static characteristics: digital pins”: updated.
•Table 50 “Static characteristics: analog I/O pins (DP, DM)”: updated VHSDI.
•Table 56 “Dynamic characteristics: reset and clock”: updated.
•Table 58 “Dynamic characteristics: analog I/O pins (DP and DM)”: updated.
•Section 16 “Application information”: updated.
•Removed soldering information.
ISP1507A_ISP1507B_2 20090119 Product data sheet - ISP1507A_ISP1507B_1
ISP1507A_ISP1507B_1 20080519 Product data sheet - -

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  78 of 82
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
21. Tables
Table 1. Ordering information  . . . . . . . . . . . . . . . . . . . . .3
Table 2. Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5
Table 3. Recommended charge pump capacitor value .13
Table 4. ULPI signal description  . . . . . . . . . . . . . . . . . .16
Table 5. Signal mapping during low-power mode  . . . . .17
Table 6. Signal mapping for 6-pin serial mode  . . . . . . .18
Table 7. Signal mapping for 3-pin serial mode  . . . . . . .19
Table 8. Operating states and their corresponding resistor 
settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Table 9. OTG_CTRL register power control bits . . . . . .26
Table 10. TXCMD byte format . . . . . . . . . . . . . . . . . . . . .27
Table 11. RXCMD byte format  . . . . . . . . . . . . . . . . . . . .27
Table 12. LINESTATE[1:0] encoding for upstream facing 
ports: peripheral . . . . . . . . . . . . . . . . . . . . . . . .28
Table 13. LINESTATE[1:0] encoding for downstream facing 
ports: host  . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Table 14. Encoded VBUS voltage state  . . . . . . . . . . . . . .29
Table 15. VBUS indicators in RXCMD required for typical 
applications  . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Table 16. Encoded USB event signals  . . . . . . . . . . . . . .31
Table 17. PHY pipeline delays  . . . . . . . . . . . . . . . . . . . .35
Table 18. Link decision times  . . . . . . . . . . . . . . . . . . . . .36
Table 19. Immediate register set overview  . . . . . . . . . . .49
Table 20. Extended register set overview . . . . . . . . . . . .49
Table 21. VENDOR_ID_LOW - Vendor ID Low register 
(address R = 00h) bit description . . . . . . . . . . .50
Table 22. VENDOR_ID_HIGH - Vendor ID High register 
(address R = 01h) bit description . . . . . . . . . . .50
Table 23. PRODUCT_ID_LOW - Product ID Low register 
(address R = 02h) bit description . . . . . . . . . . .50
Table 24. PRODUCT_ID_HIGH - Product ID High register 
(address R = 03h) bit description . . . . . . . . . . .50
Table 25. FUNC_CTRL - Function Control register (address 
R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit 
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Table 26. FUNC_CTRL - Function Control register (address 
R = 04h to 06h, W = 04h, S = 05h, C = 06h) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Table 27. INTF_CTRL - Interface Control register (address 
R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit 
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Table 28. INTF_CTRL - Interface Control register (address 
R = 07h to 09h, W = 07h, S = 08h, C = 09h) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Table 29. OTG_CTRL - OTG Control register (address R = 
0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit 
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Table 30. OTG_CTRL - OTG Control register (address R = 
0Ah to 0Ch, W = 0Ah, S = 0Bh, C = 0Ch) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Table 31. USB_INTR_EN_R_E - USB Interrupt Enable 
Rising Edge register (address R = 0Dh to 0Fh, 
W = 0Dh, S = 0Eh, C = 0Fh) bit allocation . . . .54
Table 32. USB_INTR_EN_R_E - USB Interrupt Enable 
Rising Edge register (address R = 0Dh to 0Fh, 
W = 0Dh, S = 0Eh, C = 0Fh) bit description  . .54
Table 33. USB_INTR_EN_F_E - USB Interrupt Enable 
Falling Edge register (address R = 10h to 12h, 
W = 10h, S = 11h, C = 12h) bit allocation . . . . 54
Table 34. USB_INTR_EN_F_E - USB Interrupt Enable 
Falling Edge register (address R = 10h to 12h, 
W = 10h, S = 11h, C = 12h) bit description . . . 54
Table 35. USB_INTR_STAT - USB Interrupt Status register 
(address R = 13h) bit allocation  . . . . . . . . . . . 55
Table 36. USB_INTR_STAT - USB Interrupt Status register 
(address R = 13h) bit description  . . . . . . . . . . 55
Table 37. USB_INTR_L - USB Interrupt Latch register 
(address R = 14h) bit allocation  . . . . . . . . . . . 55
Table 38. USB_INTR_L - USB Interrupt Latch register 
(address R = 14h) bit description  . . . . . . . . . . 56
Table 39. DEBUG - Debug register (address R = 15h) bit 
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 40. DEBUG - Debug register (address R = 15h) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 41. SCRATCH - Scratch register (address R = 
16h to 18h, W = 16h, S = 17h, C = 18h) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 42. PWR_CTRL - Power Control register (address 
R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit 
allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 43. PWR_CTRL - Power Control register (address 
R = 3Dh to 3Fh, W = 3Dh, S = 3Eh, C = 3Fh) bit 
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 44. Limiting values  . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 45. Recommended operating conditions  . . . . . . . 59
Table 46. Static characteristics: supply pins . . . . . . . . . . 60
Table 47. Static characteristics: digital pins  . . . . . . . . . . 60
Table 48. Static characteristics: digital pin FAULT  . . . . . 61
Table 49. Static characteristics: digital pin PSW_N  . . . . 61
Table 50. Static characteristics: analog I/O pins 
(DP, DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 51. Static characteristics: charge pump  . . . . . . . . 63
Table 52. Static characteristics: VBUS comparators  . . . . 63
Table 53. Static characteristics: VBUS resistors . . . . . . . . 64
Table 54. Static characteristics: ID detection circuit  . . . . 64
Table 55. Static characteristics: resistor reference . . . . . 64
Table 56. Dynamic characteristics: reset and clock  . . . . 66
Table 57. Dynamic characteristics: digital I/O pins . . . . . 67
Table 58. Dynamic characteristics: analog I/O pins (DP and 
DM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Table 59. Recommended bill of materials . . . . . . . . . . . . 70
Table 60. Abbreviations  . . . . . . . . . . . . . . . . . . . . . . . . . 75
Table 61. Revision history . . . . . . . . . . . . . . . . . . . . . . . . 77

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  79 of 82
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
22. Figures
Fig 1. Block diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Fig 2. Pin configuration HVQFN32; top view . . . . . . . . . .5
Fig 3. External capacitors connection . . . . . . . . . . . . . . 11
Fig 4. Charge pump capacitor . . . . . . . . . . . . . . . . . . . .13
Fig 5. Internal power-on reset timing . . . . . . . . . . . . . . .21
Fig 6. Power-up and reset sequence required before the 
ULPI bus is ready for use  . . . . . . . . . . . . . . . . . .23
Fig 7. Interface behavior with respect to RESET_N  . . .24
Fig 8. Entering and exiting 3-state in normal mode . . . .25
Fig 9. Entering and exiting 3-state in suspend mode. . .25
Fig 10. Single and back-to-back RXCMDs from the 
ISP1507 to the link. . . . . . . . . . . . . . . . . . . . . . . .28
Fig 11. RXCMD A_VBUS_VLD indicator source . . . . . . .30
Fig 12. Example of register write, register read, extended 
register write and extended register read  . . . . . .32
Fig 13. USB reset and high-speed detection handshake 
(chirp) sequence  . . . . . . . . . . . . . . . . . . . . . . . . .34
Fig 14. Example of using the ISP1507 to transmit and 
receive USB data. . . . . . . . . . . . . . . . . . . . . . . . .35
Fig 15. High-speed transmit-to-transmit packet timing  . .37
Fig 16. High-speed receive-to-transmit packet timing . . .37
Fig 17. Preamble sequence. . . . . . . . . . . . . . . . . . . . . . .38
Fig 18. Full-speed suspend and resume . . . . . . . . . . . . .40
Fig 19. High-speed suspend and resume . . . . . . . . . . . .42
Fig 20. Remote wake-up from low-power mode  . . . . . . .44
Fig 21. Transmitting USB packets without automatic SYNC 
and EOP generation  . . . . . . . . . . . . . . . . . . . . . .45
Fig 22. Example of transmit followed by receive in 6-pin 
serial mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Fig 23. Example of transmit followed by receive in 3-pin 
serial mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Fig 24. Human body ESD test model  . . . . . . . . . . . . . . .58
Fig 25. Charge pump supply current as a function of VBUS 
output current. . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Fig 26. VBUS output voltage as a function of VBUS output 
current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Fig 27. VBUS output voltage as a function of charge pump 
supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Fig 28. Charge pump supply current as a function of 
temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Fig 29. Rise time and fall time . . . . . . . . . . . . . . . . . . . . .69
Fig 30. Timing of TX_DAT and TX_SE0 to DP and DM. .69
Fig 31. Timing of TX_ENABLE to DP and DM. . . . . . . . .69
Fig 32. Timing of DP and DM to RX_RCV, RX_DP and 
RX_DM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Fig 33. ULPI interface timing . . . . . . . . . . . . . . . . . . . . . .69
Fig 34. Using the ISP1507 with an OTG controller; internal 
charge pump is utilized and crystal is attached . .71
Fig 35. Using the ISP1507 with a standard USB host 
controller; external 5 V source with built-in FAULT 
and external square wave input on XTAL1  . . . . .72
Fig 36. Using the ISP1507 with a standard USB peripheral 
controller; external crystal . . . . . . . . . . . . . . . . . .73
Fig 37. Package outline SOT617-1 (HVQFN32) . . . . . . .74

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  80 of 82
continued >>
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
Contents
General description . . . . . . . . . . . . . . . . . . . . . .  1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
Ordering information. . . . . . . . . . . . . . . . . . . . .  3
Block diagram  . . . . . . . . . . . . . . . . . . . . . . . . . .  4
Pinning information. . . . . . . . . . . . . . . . . . . . . .  5
1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
2 Pin description  . . . . . . . . . . . . . . . . . . . . . . . . .  5
Functional description  . . . . . . . . . . . . . . . . . . .  8
1 ULPI interface controller . . . . . . . . . . . . . . . . . .  8
2 USB data serializer and deserializer. . . . . . . . .  8
3 Hi-Speed USB (USB 2.0) ATX  . . . . . . . . . . . . .  8
4 Voltage regulator. . . . . . . . . . . . . . . . . . . . . . . .  9
5 Crystal oscillator and PLL. . . . . . . . . . . . . . . . .  9
6 OTG module . . . . . . . . . . . . . . . . . . . . . . . . . . .  9
6.1 ID detector  . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
6.2 VBUS comparators. . . . . . . . . . . . . . . . . . . . . .  10
6.2.1 VBUS valid comparator  . . . . . . . . . . . . . . . . . .  10
6.2.2 Session valid comparator . . . . . . . . . . . . . . . .  10
6.2.3 Session end comparator. . . . . . . . . . . . . . . . .  10
6.3 SRP charge and discharge resistors  . . . . . . .  10
6.4 Charge pump . . . . . . . . . . . . . . . . . . . . . . . . .   11
7 Band gap reference voltage . . . . . . . . . . . . . .   11
8 Power-On Reset (POR) . . . . . . . . . . . . . . . . .   11
9 Detailed description of pins. . . . . . . . . . . . . . .   11
9.1 DATA[7:0] . . . . . . . . . . . . . . . . . . . . . . . . . . . .   11
9.2 VCC(I/O)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
9.3 RREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
9.4 DP and DM . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
9.5 FAULT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
9.6 ID  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
9.7 CPGND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
9.8 C_A and C_B . . . . . . . . . . . . . . . . . . . . . . . . .  13
9.9 VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
9.10 PSW_N. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
9.11 VBUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
9.12 REG3V3 and REG1V8 . . . . . . . . . . . . . . . . . .  14
9.13 XTAL1 and XTAL2  . . . . . . . . . . . . . . . . . . . . .  14
9.14 RESET_N . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
9.15 DIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
9.16 STP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
9.17 NXT  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
9.18 CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
9.19 CHIP_SELECT_N  . . . . . . . . . . . . . . . . . . . . .  15
9.20 GND (die pad). . . . . . . . . . . . . . . . . . . . . . . . .  15
Modes of operation . . . . . . . . . . . . . . . . . . . . .  16
1 ULPI modes . . . . . . . . . . . . . . . . . . . . . . . . . .   16
1.1 Synchronous mode  . . . . . . . . . . . . . . . . . . . .   16
1.2 Low-power mode . . . . . . . . . . . . . . . . . . . . . .   17
1.3 6-pin full-speed or low-speed serial mode . . .   18
1.4 3-pin full-speed or low-speed serial mode . . .   18
2 USB and OTG state transitions . . . . . . . . . . .   19
Protocol description . . . . . . . . . . . . . . . . . . . .   21
1 ULPI references . . . . . . . . . . . . . . . . . . . . . . .   21
2 Power-On Reset (POR) . . . . . . . . . . . . . . . . .   21
3 Power-up, reset and bus idle sequence. . . . .   21
3.1 Interface protection  . . . . . . . . . . . . . . . . . . . .   23
3.2 Interface behavior with respect to RESET_N    24
3.3 Interface behavior with respect to 
CHIP_SELECT_N . . . . . . . . . . . . . . . . . . . . .   24
4 VBUS power and fault detection . . . . . . . . . . .   26
4.1 Driving 5 V on VBUS . . . . . . . . . . . . . . . . . . . .   26
4.2 Fault detection . . . . . . . . . . . . . . . . . . . . . . . .   26
5 TXCMD and RXCMD . . . . . . . . . . . . . . . . . . .   26
5.1 TXCMD  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   26
5.2 RXCMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   27
5.2.1 Linestate encoding. . . . . . . . . . . . . . . . . . . . .   28
5.2.2 VBUS state encoding. . . . . . . . . . . . . . . . . . . .   29
5.2.3 Using and selecting the VBUS state encoding    30
5.2.4 RxEvent encoding . . . . . . . . . . . . . . . . . . . . .   31
6 Register read and write operations  . . . . . . . .   32
7 USB reset and high-speed detection handshake 
(chirp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   32
8 USB packet transmit and receive. . . . . . . . . .   35
8.1 USB packet timing . . . . . . . . . . . . . . . . . . . . .   35
8.1.1 ISP1507 pipeline delays  . . . . . . . . . . . . . . . .   35
8.1.2 Allowed link decision time  . . . . . . . . . . . . . . .   36
9 Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . .   37
10 USB suspend and resume . . . . . . . . . . . . . . .   38
10.1 Full-speed or low-speed host-initiated suspend 
and resume  . . . . . . . . . . . . . . . . . . . . . . . . . .   38
10.2 High-speed suspend and resume  . . . . . . . . .   40
10.3 Remote wake-up . . . . . . . . . . . . . . . . . . . . . .   43
11 No automatic SYNC and EOP generation 
(optional)  . . . . . . . . . . . . . . . . . . . . . . . . . . . .   44
12 On-The-Go operations . . . . . . . . . . . . . . . . . .   45
12.1 OTG charge pump . . . . . . . . . . . . . . . . . . . . .   46
12.2 OTG comparators  . . . . . . . . . . . . . . . . . . . . .   46
12.3 Pull-up and pull-down resistors . . . . . . . . . . .   46
12.4 ID detection . . . . . . . . . . . . . . . . . . . . . . . . . .   46
12.5 VBUS charge and discharge resistors. . . . . . .   46
13 Serial modes  . . . . . . . . . . . . . . . . . . . . . . . . .   46
14 Aborting transfers. . . . . . . . . . . . . . . . . . . . . .   48
15 Avoiding contention on the ULPI data bus . . .   48

ISP1507A_ISP1507B_3 © ST-ERICSSON 2009. All rights reserved.
Product data sheet Rev. 03 — 22 October 2009  81 of 82
ISP1507A; ISP1507B
ULPI HS USB OTG transceiver
Register map  . . . . . . . . . . . . . . . . . . . . . . . . . .  49
1 Immediate register set  . . . . . . . . . . . . . . . . . .  50
1.1 Vendor ID and Product ID registers . . . . . . . .  50
1.1.1 VENDOR_ID_LOW register . . . . . . . . . . . . . .  50
1.1.2 VENDOR_ID_HIGH register. . . . . . . . . . . . . .  50
1.1.3 PRODUCT_ID_LOW register . . . . . . . . . . . . .  50
1.1.4 PRODUCT_ID_HIGH register  . . . . . . . . . . . .  50
1.2 FUNC_CTRL register . . . . . . . . . . . . . . . . . . .  50
1.3 INTF_CTRL register . . . . . . . . . . . . . . . . . . . .  51
1.4 OTG_CTRL register . . . . . . . . . . . . . . . . . . . .  52
1.5 USB_INTR_EN_R_E register. . . . . . . . . . . . .  54
1.6 USB_INTR_EN_F_E register . . . . . . . . . . . . .  54
1.7 USB_INTR_STAT register  . . . . . . . . . . . . . . .  55
1.8 USB_INTR_L register. . . . . . . . . . . . . . . . . . .  55
1.9 DEBUG register . . . . . . . . . . . . . . . . . . . . . . .  56
1.10 SCRATCH register . . . . . . . . . . . . . . . . . . . . .  56
1.11 Reserved  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56
1.12 Access extended register set . . . . . . . . . . . . .  56
1.13 Vendor-specific registers  . . . . . . . . . . . . . . . .  57
1.14 PWR_CTRL register. . . . . . . . . . . . . . . . . . . .  57
2 Extended register set . . . . . . . . . . . . . . . . . . .  57
ElectroStatic Discharge (ESD) . . . . . . . . . . . .  58
1 ESD protection . . . . . . . . . . . . . . . . . . . . . . . .  58
2 ESD test conditions  . . . . . . . . . . . . . . . . . . . .  58
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . .  59
Recommended operating conditions. . . . . . .  59
Static characteristics. . . . . . . . . . . . . . . . . . . .  60
Dynamic characteristics . . . . . . . . . . . . . . . . .  66
1 ULPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . .  69
Application information. . . . . . . . . . . . . . . . . .  70
Package outline . . . . . . . . . . . . . . . . . . . . . . . .  74
Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . .  75
References . . . . . . . . . . . . . . . . . . . . . . . . . . . .  75
Revision history. . . . . . . . . . . . . . . . . . . . . . . .  77
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  79
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80

Product data sheet Rev. 03 — 22 October 2009 82 of 82

ISP1507A; ISP1507B

ULPI HS USB OTG transceiver

Please Read Carefully:

The contents of this document are subject to change without prior notice. ST-Ericsson makes no representation or warranty of any nature

whatsoever (neither expressed nor implied) with respect to the matters addressed in this document, including but not limited to warranties of

merchantability or fitness for a particular purpose, interpretability or interoperability or, against infringement of third party intellectual property

rights, and in no event shall ST-Ericsson be liable to any party for any direct, indirect, incidental and or consequential damages and or loss

whatsoever (including but not limited to monetary losses or loss of data), that might arise from the use of this document or the information in it.

ST-Ericsson and the ST-Ericsson logo are trademarks of the ST-Ericsson group of companies or used under a license from

STMicroelectronics NV or Telefonaktiebolaget LM Ericsson.

All other names are the property of their respective owners.

Contact information at www.stericsson.com under Contacts