Analog POL
Front Ends
Modular Products
Ruggedized
Z-One® Digital Power
Isolated DC-DC
Chassis Mount
PoE
CompactPCI
2010 ONLINE AC-DC & DC-DC
POWER SOLUTIONS PRODUCT UPDATE
Distributed Power
Non- 1/16 1/8 1/4 1/2
Brick Brick Brick Brick Brick
Bus Converters 7 7 7
Power over Ethernet 7
Single Output - SMT 22 21 21
Single Output - TH 10 8 8 9 10
Dual Output - SMT 23 22
Dual Output - TH 13 12 12
Triple Output - TH 16
Quad Output - TH 18
Input Filters - SMT 23
Input Filters - TH 20
Table of Contents
Rack and Chassis-Mount Front Ends
Rack-Mount Single Output 25
Rack-Mount Power Shelves 27
Chassis-Mount Single Output 28
SMT = Surface Mount
TH = Through Hole
Board Mount
Isolated DC-DC
Point-Of-Load Conversion & Management
Bus Programmable Digital POL Solutions 2
No-BusTM Digital POL Converters 2
Y-Series Analog POLs 4
Board-Mount DC-DC
Brick
Overview
Page 6
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life
support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional
president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date
manufactured. Specifications are subject to change without notice.
Railway
& Rugged
Overview
Page 47
Board-Only, U-Channel, & Enclosed
AC-DC Single Output 40 to 7000 Watts 28
AC-DC Dual Output 125 to 150 Watts 29
AC-DC Triple Output 37 to 150 Watts 30
AC-DC Quad Output Under 100 Watts 30
110 to 125 Watts 31
130 to 150 Watts 31
200 to 375 Watts 32
Open-Frame Linears
Single Output 34
Dual Output 35
Triple Output 36
CompactPCI & PoE
CompactPCI 37
Power Over Ethernet 38
Modular AC-DC
LPM615 33
DIN-Rail Mount, AC-DC & DC-DC
LOK Series 40
W Series, Includes EN50155 Models 40
X Series with PFC 41
Battery Chargers 41
Cassettes & Positive Switching Regulators
DC-DC Cassettes K M S P Q
47 44 45 48 46
AC-DC Cassettes M H S S/PFC K K/PFC KP/PFC
50 50 51 51 51 51 51
Cassette Battery Chargers 50
Positive Switching Regulators 42
Chassis Mount
Specialty
Railway & Rugged
Power-One, maXyz, No-Bus, Z-One, Z Digital IBA, and Z-POL are trademarks and/or logos of Power-One, Inc.
2
Z-One
®
Digital Power
Signals and Protections
Reporting of output current and
temperature via signal pins.
Thresholds for overvoltage,
undervoltage, and Power Good
track the output voltage settings.
Output voltages (0.5 to 5.5 V) and turn-on delays are configured
with an external resistor and a capacitor, respectively.
Up to four No-Bus POLs can current share using a single control trace.
No-Bus POLs can start up with pre-biased outputs.
Sink and source current capabilities for active bus termination.
Coordination and
Optimization via
Simple Pin Strapping
Frequency synchronization and
phase interleaving reduce EMI.
Comprehensive sequencing and
cascading management.
Feedback loop compensation and
enable logic.
Frequency synchronization, fault
propagation, and current sharing are
implemented, without external
components, by interconnecting
pins on the Z-POLs being
coordinated.
t
t
t
t
No-Bus POL Converters
t
t
Power-One’s No-Bus™ POL converters provide sophisticated power
management capabilities without the cost and complexity of third-party
controllers and the communication bus interfaces required by analog
architectures.
TM
Bus Programmable POL Solutions
Power-One’s bus-programmable POL solutions combine many
innovative operating concepts to achieve an unprecedented level of
power-system integration. A multitude of parameters, such as output
voltages, sequencing, tracking, and protection limits are user-
programmed via I2C, or GUI, and stored in a Digital Power Manager.
Although Z-One®Digital Power can be programmed via an I2C bus,
it does not require users to provide an I2C interface, host processor,
or non-volatile memory; Z-One®Digital Power can operate
autonomously in any system. Additional features include:
Open architecture based on industry standard I2C interface.
Wide input ranges and programmable outputs reduce the
number of unique models in inventory.
Extremely scalable architecture provides up to 32 programmable
outputs from 0.5 to 5.5 VDC.
Significantly reduced component count improves reliability,
power density, and cost.
GUI-driven configuration and simulation simplifies power
system development, accelerating time to market.
Fully-integrated point-of-load solution eliminates component
incompatibility issues.
Manages up to four analog components including VRMs, POLs,
fans, and linear regulators.
ZM7300 Series controllers can manage analog components
(including VRMs, linear regulators, POLs, and fans) and Z-POL
converters for a total of 32 devices. I2C communication with host
systems in 100 kbs and 400 kbs modes of operation is supported.
These 9 x 9mm QFN-package controllers can be purchased
preprogrammed, or can be user programmed via an IEEE 1149.1
compliant JTAG port or via the Z-Series GUI and the I2C port.
Additional features include:
Ensures data integrity by storing configuration instructions in
non-volatile memory.
Collects I2C compatible POL performance data (output voltage,
output current, POL temperature, and protection status).
Monitors the intermediate bus, accepts interrupts, initiates
crowbar protection, and interfaces with dc-dc bus converters
and ac-dc front ends.
Output Voltages and Currents
TM
IBA Regulated
Bus Converter
Host
System
PC-Based
GUI
9 mm
ZM7300 Digital
Power Managers
3
Digital POL Conversion and Management
2.4 x 0.55 x 1.1 inch
61 x 14 x 27.9 mm
ZY2160 & ZY8160
Bus Programmable Digital POLs
Input Output Max
Voltage Program Range Amps Efficiency Model
Latest-Generation High Efficiency Digital POLs
8 to 14 +0.5 to +5.5 6 92% ZY8105
8 to 14 +0.5 to +5.5 10 92% ZY8110
8 to 14 +0.5 to +5.5 20 92% ZY8120
8 to 14 +0.5 to +3.65 40 94% ZY8140
8 to 14 +0.5 to +2.75 60 92% ZY8160
Ultra-Wide Input Digital POLs
3 to 14 +0.5 to +5.5 7 92% ZY7007
3 to 13.2 +0.5 to +5.5 10 90% ZY7010
3 to 13.2 +0.5 to +5.5 15 92% ZY7015
3 to 13.2 +0.5 to +5.5 15 94% ZY7115
3 to 13.2 +0.5 to +5.5 20 92% ZY7120
Input Output Max
Voltage Trim Range Amps Efficiency Model
Latest-Generation High Efficiency Digital POLs
8 to 14 +0.5 to +5.5 5 93% ZY2105
8 to 14 +0.5 to +5.5 10 92% ZY2110
8 to 14 +0.5 to +5.5 20 92% ZY2120
8 to 14 +0.5 to +3.6 40 93% ZY2140
8 to 14 +0.5 to +2.75 60 93% ZY2160
Ultra-Wide Input Digital POLs
3 to 14 +0.5 to +5.5 7 92% ZY1207
3 to 14 +0.5 to +5.5 15 94% ZY1015
3 to 14 +0.5 to +5.5 15 94% ZY1115
3 to 14 +0.5 to +5.5 20 92% ZY1120
Model Digital POL Analog Component Combined
Number Management Nodes Management Nodes Nodes*
ZM7304 4 4 4
ZM7308 8 4 8
ZM7316 16 4 16
ZM7332 32 4 32
* Combined nodes are the maximum number of analog and digital components that can be concurrently managed.
ZM7300 Series Digital Power Managers
No-Bus Digital POLs
1.25 x 0.55 x 0.31 inch
32 x 14 x 8 mm
ZY11XX & ZY71XX
1.25 x 0.55 x 0.28 inch
32 x 14 x 7.1 mm
ZY7010, ZY7015, & ZY1015
0.87 x 0.49 x 0.26 inch
22.2 x 12.5 x 6.5 mm
ZY7007 & ZY1207
Controls up to 32 Bus
Programmable POLs and 4
analog components
Compact 9 x 9 mm package
ZM7300 Digital Power Manager
1.2 x 0.26 x 0.84 inch
30.5 x 6.6 x 21.3 mm
ZY2105 & ZY8105
1.2 x 0.26 x 0.84 inch
30.5 x 6.6 x 21.3 mm
ZY2110 & ZY8110
1.6 x 0.84 x 0.41 inch
40.6 x 21.3 x 10.4 mm
ZY2120 & ZY8120
1.8 x 0.55 x 1.1 inch
45.7 x 14 x 27.9 mm
ZY2140 & ZY8140
4
www.power-one.com
Analog POL Converters
1.30 x 0.53 x 0.31 inch
33 x 13.5 x 8 mm
0.8 x 0.45 x 0.25 inch
20.3 x 11.4 x 6.3 mm
YM05S, YM12S, & YNM05S
YNC, YNL, & YS
1.00 x 0.50 x 0.48 inch
25.4 x 12.7 x 12.2 mm
YPB09S
Input Max Output
Voltage Amps Trim Range Efficiency Model
Models with 5.5Vin and Lower, Sorted by Max Amps
3 to 5.5 5 +0.75 to +3.63 94% YM05S05
3 to 5.5 6 +0.75 to +3.63 93% YNM05S06
3 to 5.5 10 +1.1 to +1.3 87% YNL05S10012
3 to 5.5 10 +1.7 to +1.9 91% YNL05S10018
3 to 5.5 10 +2.3 to +2.7 93% YNL05S10025
3 to 5.5 10 +3 to +3.6 94% YNL05S10033
3 to 5.5 10 +0.75 to +3.63 94% YS05S10
3 to 5.5 16 +0.75 to +3.63 93% YS05S16
4.5 to 5.5 20 +0.75 to +3.63 94% YNC05S20
Model with 4.5 to 13.5Vin
4.5 to 13.5 30 +0.8 to +1.8 90% YPB09S30
Models with 9.6 to 14Vin, Sorted by Max Amps
9.6 to 14 5 +0.75 to +5.5 92% YM12S05
9.6 to 14 10 +1.7 to +1.9 90% YNL12S10018
9.6 to 14 10 +4.5 to +5.5 95% YNL12S10050
9.6 to 14 16 +0.75 to +5.5 94% YS12S16
9.6 to 14 20 +0.75 to +5.5 94% YNC12S20
Y-Series (DOSA-Compliant) Surface-Mount POL Converters
YEV-Series POLs combine ultra-high efficiencies with excellent
thermal management to provide current-dense footprints, and low
profiles that minimize impedance to system airflow; enhancing
cooling for both upstream and downstream devices.
Industry-standard SIP packages.
Wide input voltage range: 4.5 V–13.8 V.
3, 6, and 10-amp models (top picture) utilize compact
0.41 x 0.40 x 0.65 inch (10.4 x 10.2 x 16.5 mm) packages.
20-amp model (bottom picture) utilizes a compact 1.45 x
0.34 x 0.61 inch (36.8 x 8.6 x 15.5 mm) package.
Exceptional thermal performance, even in high temperature
environments with minimal airflow.
Rugged designs provide MTBFs up to 67 million hours.
3, 6, 10, and 20-Amp YEV-Series POLs Provide
Tightly-Regulated 0.59 - 5.1V Trimmable Outputs
5
Analog POL Converters
YNV05T06 & YNV12T05
YNV05T10, YNV05T10XXX,
YNV05T16, YNV12T10,
& YNV12T16
2.0 x 0.54 x 0.28 inch
50.8 x 13.6 x 7.1 mm
0.90 x 0.40 x 0.21 inch
22.9 x 10.2 x 5.4 mm
YH09T40
1.45 x 1.12 x 0.5 inch
36.8 x 28.3 x 12.7 mm
Input Max Output
Voltage Amps Trim Range Efficiency Model
Models with 3.3 to 5.5Vin, Sorted by Max Amps
3 to 5.5 6 +0.75 to +3.63 93% YNV05T06
3 to 5.5 10 +0.75 to +3.63 95% YNV05T10
3 to 5.5 10 +3 to +3.6 95% YNV05T10033
3 to 5.5 16 +0.75 to +3.63 93% YNV05T16
Models with 4.5 to 13.8Vin, Sorted by Max Amps (DOSA does not specify YEV equivalents)
4.5 to 13.8 3 +0.6 to +5.1 93% YEV09T03
4.5 to 13.8 6 +0.6 to +5.1 93% YEV09T06
4.5 to 13.8 10 +0.6 to +5.1 93% YEV09T10
4.5 to 13.8 20 +0.6 to +5.1 93% YEV09T20
Model with 5 to 13.8Vin, Sorted by Max Amps
5 to 13.8 40 +0.6 to +3.63 92% YH09T40
5 to 13.8 60 +0.6 to +3.63 93% YV09T60
Models with 9.6 and Higher Vin, Sorted by Max Amps
9.6 to 14 5 +0.75 to +5.5 90% YNV12T05
9.6 to 14 10 +0.75 to +5.5 94% YNV12T10
9.6 to 14 16 +0.75 to +5.5 94% YNV12T16
10 to 14 25 +0.8 to +5.5 94% YV12T25
Y-Series (DOSA-Compliant) Through-Hole POL Converters
2.00 x 1.25 x 0.34 inch
50.8 x 31.8 x 8.5 mm
YV12T25
2.58 x 0.63 x 1.25 inch
65.5 x 16 x 31.7 mm
The YV09T60 POL converter offers exceptional thermal performance,
even in high temperature environments with minimal airflow.
Industry-standard SIP package
High-efficiency multiphase synchronous buck topology
Low-noise fixed-frequency operation
Overcurrent, output overvoltage, and overtemperature
protections with automatic restart
Wide input voltage range: 5 V–13.8 V
Extended operating temperature range: 0 to 70 ºC
Current-Dense YV09T60 POL Delivers a 60 Amp
0.6 V – 3.63 V Programmable Output
6
Isolated DC-DC Converters
An Industry-Leading Selection of High-Efficiency DC-DC Bricks
The DOSA-compliant SSQE48T20033 20-amp, 3.3 Vout,
sixteenth-brick delivers power densities up to 56 watts per
square inch. Additional features include:
• Ultra-low profile height: 0.374”.
• Full Telco input range: 36-75 VDC.
• Capability to withstand a 100 V input transient for 100 ms.
• On-board input differential LC-filtering.
• SMT and through-hole-mount models are available.
Cost-Effective Sixteenth-Brick
Provides up to 92% Efficiency
The latest SQE48T Series eighth-bricks provide single-output
elevated-temperature performance that exceeds most similar-
amperage quarter-bricks. Additional features include:
• Wide range 36-75 VDC inputs.
• 2250 VDC input-to-output isolation provides Basic insulation.
• Start-up into highly-capacitive loads.
• Rugged design withstands a 100 V input transient for 100 ms.
40 and 50 Amp Eighth-Bricks Deliver
Best-in-Class Elevated Temperature Performance
High-Efficiency Bus Converters,
Fixed Ratio and Wide-Input Models Available
Bus converter products include models with ultra-high
efficiencies (up to 97%). Available features include:
• Fixed ratio (4:1 and 5:1) and wide input models.
• A wide range of output voltages facilitates selecting the
most efficient bus voltage for a specific application.
• Extended operating-temperature ranges: -40 to +85 °C.
• High reliability: MTBF = 20 million hours.
High-Current-Density QME Quarter-Bricks
Available with Outputs from 1 to 12 VDC
QME Series products provide up to 40 amps from industry-
standard quarter-brick footprints. Additional features include:
• Outstanding thermal performance in high ambient
temperature environments.
• No minimum load required.
• Capability to start-up into pre-biased loads.
• Rugged design withstands 100 V input transient for 100 ms.
Power-One offers a comprehensive range of DPA bricks and
IBA regulated bus converters, in footprints from 1/16 to 1/2.
Industry-leading efficiencies, and advanced thermal-
management techniques increase current densities, reduce
power consumption, and provide more power in elevated-
temperature environments.
These flexible products can be used as isolated DC-DC
converters, in applications with separate input/output grounds,
or used as non-isolated converters in applications with common
input/output grounds. DOSA-compliant models are available.
Please refer to the product selection tables on the following
pages for model-level details.
7
Isolated DC-DC > Thru-Hole > Single Output
Unsigned output voltages are isolated and can be used as either + or - polarities.
HHS04 & HHS05
2.40 x 2.28 x 0.42 inch
61.0 x 57.9 x 10.7 mm
HDS & HKS
2.40 x 2.28 x 0.50 inch
61.0 x 57.9 x 12.7 mm
HBC48T
2.40 x 2.28 x 0.50 inch
61.0 x 57.9 x 12.7 mm
QBC
2.28 x 1.45 x 0.43 inch
57.9 x 36.8 x 11 mm
QME48T
2.30 x 1.45 x 0.48 inch
58.4 x 36.8 x 12.2 mm
Max Brick Factory Output Input Vout
Amps Size Set Vout Range Voltage Regulation Efficiency Model
Models with fixed-ratio inputs/outputs
20 1/8 N/A 8.7 to 13.7 42 to 53 5.1 fixed ratio 96% SQT48T20120
27 1/8 N/A 6.7 to 11 38 to 55 5.1 fixed ratio 95% SQT48T27096
38 1/8 N/A 7 to 11 38 to 55 5.1 fixed ratio 95% SQT48T38096
25 1/4 N/A 10.5 to 13.3 42 to 53 4.1 fixed ratio 96% QTS48T25120
38 1/4 N/A 7.2 to 11 36 to 55 5.1 fixed ratio 96% QTS48T38096
46 1/4 N/A 7.2 to 11 36 to 55 5.1 fixed ratio 97% QTS48T46096
Models with wide-range inputs
10 1/8 12 9.6 to 13.2 36 to 75 2% total 93% SQE48T10120
11 1/4 12 9.6 to 13.2 36 to 75 5% total 91% QBC11ZH
20 1/4 12 9.6 to 13.2 36 to 75 2% total 93% QME48T20120
25 1/2 12 9.6 to 13.2 36 to 75 2% total 93% HBC48T25120
30 1/2 12 10.8 to 13.2 36 to 75 3% total 91% HDS48T30120
32 1/2 12 10.8 to 13.2 35 to 75 4% total 94% HKS48T30120
Thru-Hole > Single-Output > Bus Converters
Additional single-output products are listed in the
through-hole and surface-mount isolated DC-DC sections.
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
36 to 75 52.5 50 to 53 3.8 HHS04Z52
36 to 75 53.7 51.2 to 54.2 4.8 HHS05Z55
Thru-Hole > Single-Output > Power Over Ethernet
QTS48T38, QTS48T46
QTS48T25
2.28 x 1.45 x 0.50 inch
57.9 x 36.8 x 12.7 mm
2.28 x 1.45 x 0.40 inch
57.9 x 36.8 x 10.2 mm
SQT48T20
2.30 x 0.9 x 0.39 inch
58.4 x 22.8 x 10 mm
SQT48T27 & SQT48T38
2.30 x 0.90 x 0.48 inch
58.4 x 22.8 x 12.1 mm
SQE48T
2.30 x 0.90 x 0.41 inch
58.4 x 22.8 x 10.3 mm
8
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Single Output
SQT48T20
2.30 x 0.9 x 0.39 inch
58.4 x 22.8 x 10 mm
SQT48T27 & SQT48T38
2.30 x 0.90 x 0.48 inch
58.4 x 22.8 x 12.1 mm
SSQE48T
1.3 x 0.9 x 0.37 inch
33 x 22.9 x 9.4 mm
SQ24T & SQ48T
2.30 x 0.90 x 0.28 inch
58.4 x 22.8 x 7.1 mm
Thru-Hole > Single-Output > 1/16-Brick
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
36 to 75 1.2 1 to 1.3 25 SSQE48T25012
36 to 75 1.5 1.2 to 1.6 25 SSQE48T25015
36 to 75 1.8 1.5 to 1.9 25 SSQE48T25018
36 to 75 2.5 2 to 2.7 25 SSQE48T25025
36 to 75 3.3 2.7 to 3.6 20 SSQE48T20033
36 to 75 3.3 2.7 to 3.6 15 SSQE48T15033
36 to 75 3.3 2.7 to 3.6 10 SSQE48T10033
36 to 75 5.0 4 to 5.5 13 SSQE48T13050
36 to 75 12.0 9.6 to 13.2 7 SSQE48T07120
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with 18 to 36Vin, Sorted by Factory Set Vout
18 to 36 2 1.6 to 2.2 15 SQ24T15020
18 to 36 3.3 2.7 to 3.6 15 SQ24T15033
18 to 36 5 4 to 5.5 10 SQ24T10050
18 to 36 6 4.8 to 6.6 8 SQ24T08060
18 to 36 12 9.6 to 13.2 4 SQ24T04120
18 to 36 15 12 to 16.5 3.3 SQ24T03150
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 1.2 1.1 to 1.3 15 SQ48T15012
36 to 75 1.2 1.1 to 1.3 30 SQE48T30012
36 to 75 1.2 1.1 to 1.3 50 SQE48T50012
36 to 75 1.5 1.2 to 1.6 15 SQ48T15015
36 to 75 1.5 1.2 to 1.6 30 SQE48T30015
36 to 75 1.5 1.2 to 1.6 40 SQE48T40015
36 to 75 1.8 1.5 to 1.9 15 SQ48T15018
36 to 75 1.8 1.5 to 1.9 30 SQE48T30018
36 to 75 1.8 1.5 to 1.9 40 SQE48T40018
36 to 75 2.5 2 to 2.7 15 SQ48T15025
36 to 75 2.5 2 to 2.7 30 SQE48T30025
36 to 75 2.5 2 to 2.7 40 SQE48T40025
36 to 75 3.3 2.7 to 3.6 15 SQ48T15033*
36 to 75 3.3 2.7 to 3.6 20 SQE48T20033
36 to 75 3.3 2.7 to 3.6 30 SQE48T30033
36 to 75 5 4 to 5.5 10 SQ48T10050
36 to 75 5 4 to 5.5 20 SQE48T20050
36 to 75 6 4.8 to 6.6 8 SQ48T08060
36 to 75 6 5.4 to 6.6 17 SQE48T17060
36 to 75 8 6.4 to 8.8 5.3 SQ48T05080
38 to 55 9.6 6.7 to 11 27 SQT48T27096 **
38 to 55 9.6 7 to 11 38 SQT48T38096 **
36 to 75 12 9.6 to 13.2 10 SQE48T10120
38 to 55 12 8.7 to 13.7 20 SQT48T20120 **
** Fixed-ratio input-to-output voltage
Thru-Hole > Single-Output > 1/8 Brick
SQE48T
2.30 x 0.90 x 0.41 inch
58.4 x 22.8 x 10.3 mm
9
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Single Output
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with 18 to 36Vin, Sorted by Factory Set Vout
18 to 36 3.3 2.7 to 3.6 25 Q24T25033
18 to 36 3.3 2.7 to 3.6 30 Q24T30033
18 to 36 5 4 to 5.5 15 Q24T15050
Models with Ultra-Wide Input, Sorted by Factory Set Vout
18 to 60 3.3 2.64 to 3.63 25 QW24T25033
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 1.2 1.1 to 1.3 30 QL48T30012
36 to 75 1.2 1.1 to 1.3 50 QM48T50012
36 to 75 1.5 1.2 to 1.6 30 Q48T30015
36 to 75 1.5 1.2 to 1.6 40 QME48T40015
36 to 75 1.8 1.5 to 1.9 25 Q48T25018
36 to 75 1.8 1.5 to 1.9 30 Q48T30018
36 to 75 1.8 1.5 to 1.9 45 QM48T45018
36 to 75 2 1.6 to 2.2 25 Q48T25020
36 to 75 2 1.8 to 2.2 40 QM48T40020
36 to 75 2 1.6 to 2.2 45 QM48T45020
36 to 75 2.5 2 to 2.7 30 Q48T30025
36 to 75 2.5 2 to 2.7 40 QME48T40025
36 to 75 2.5 2 to 2.7 45 QM48T45025
36 to 75 3.3 2.7 to 3.6 25 Q48T25033
36 to 75 3.3 2.7 to 3.6 30 Q48T30033
36 to 75 3.3 2.7 to 3.6 40 QME48T40033
36 to 75 3.3 2.7 to 3.6 45 QM48T45033
36 to 75 5 4.5 to 5.5 15 Q48T15050
36 to 75 5 4 to 5.5 20 Q48T20050
36 to 75 5 4 to 5.5 25 QM48T25050
36 to 75 5 4 to 5.5 40 QME48T40050
36 to 55 9.6 7.2 to 11 38 QTS48T38096*
36 to 55 9.6 7.2 to 11 46 QTS48T46096*
36 to 75 12 9.6 to 13.2 8 Q48T08120
36 to 75 12 9.6 to 13.2 11 QBC11ZH
36 to 75 12 9.6 to 13.2 14 QM48T14120
36 to 75 12 9.6 to 13.2 20 QME48T20120
42 to 53 12 10.5 to 13.3 25 QTS48T25120*
Thru-Hole > Single-Output > 1/4 Brick
Q24T & Q48T
2.30 x 1.45 x 0.28 inch
58.4 x 36.8 x 7.1 mm
QL48T
2.30 x 1.45 x 0.28 inch
58.4 x 36.8 x 7.1 mm
QBC
2.28 x 1.45 x 0.43 inch
57.9 x 36.8 x 11 mm
QM48T
2.30 x 1.45 x 0.31 inch
58.4 x 36.8 x 7.8 mm
QW24T25033
2.30 x 1.45 x 0.48 inch
58.4 x 36.8 x 12.2 mm
QME48T
2.30 x 1.45 x 0.48 inch
58.4 x 36.8 x 12.2 mm
QTS48T38, QTS48T46
QTS48T25
2.28 x 1.45 x 0.50 inch
57.9 x 36.8 x 12.7 mm
2.28 x 1.45 x 0.40 inch
57.9 x 36.8 x 10.2 mm
10
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Single Output
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 12 10.8 to 13.2 25 HBC48T25120
36 to 75 12 10.8 to 13.2 30 HDS48T30120
36 to 75 12 10.8 to 13.2 32 HKS48T30120
36 to 75 28 21.0 to 33.0 12.5 HBA48T12280
36 to 75 52.5 50 to 53 3.8 HHS04Z52
36 to 75 53.7 51.2 to 54.2 4.8 HHS05Z55
Thru-Hole > Single-Output > 1/2 Brick
HDS & HKS
2.40 x 2.28 x 0.50 inch
61.0 x 57.9 x 12.7 mm
HBC48T
2.40 x 2.28 x 0.50 inch
61.0 x 57.9 x 12.7 mm
HBA48T12280
2.40 x 2.28 x 0.50 inch
61.0 x 57.9 x 12.7 mm
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with 3.3Vout, Sorted by Max Amps
8.4 to 36 3.3 N/A 0.9 20IMX4-03-8
16.8 to 75 3.3 N/A 0.9 40IMX4-03-8
8.4 to 36 3.3 2.5 to 3.5 1.5 20IMX7-03-8
16.8 to 75 3.3 2.5 to 3.5 1.5 40IMX7-03-8
40 to 121 3.3 2.5 to 3.5 1.5 70IMX7-03-8
8.4 to 36 3.3 2.6 to 3.5 4.5 20IMX15-03-8RG
16.8 to 75 3.3 2.6 to 3.5 4.5 40IMX15-03-8RG
50 to 150 3.3 2.6 to 3.5 4.5 110IMY15-03-8RG
Models with 5 to 5.2Vout, Sorted by Factory Set Vout and Max Amps
4.5 to 5.5 5 N/A 0.1 DSP1N5S5
36 to 72 5 N/A 0.5 BWS4805
8.4 to 36 5 N/A 0.7 20IMX4-05-8
16.8 to 75 5 N/A 0.7 40IMX4-05-8
40 to 121 5 N/A 0.7 70IMX4-05-8
18 to 36 5 N/A 1 24IMS6-05-9
36 to 75 5 N/A 1 48IMS6-05-9
3.5 to 16 5 N/A 1.2 DFC6U5S5
3.5 to 16 5 4.5 to 5.5 2 DGP12U5S5
50 to 150 5 3.8 to 5.2 2.8 110IMY15-05-05-8
8.4 to 36 5.1 3.8 to 5.4 1.2 20IMX7-05-8
16.8 to 75 5.1 3.8 to 5.4 1.2 40IMX7-05-8
40 to 121 5.1 3.8 to 5.4 1.2 70IMX7-05-8
60 to 150 5.1 3.8 to 5.4 1.2 110IMX7-05-8
8.4 to 36 5.1 4.1 to 5.4 2.3 20IMX15-05-8R
16.8 to 75 5.1 4.1 to 5.4 2.5 40IMX15-05-8R
50 to 150 5.1 4.1 to 5.4 2.5 110IMY15-05-8R
14 to 36 5.1 4.1 to 5.4 2.7 24IMS15-05-9R
36 to 75 5.1 4.1 to 5.4 2.7 48IMS15-05-9R
8.4 to 36 5.1 3.8 to 5.3 3.5 20IMX15-05-8RG
16.8 to 75 5.1 3.8 to 5.3 3.5 40IMX15-05-8RG
50 to 150 5.1 3.8 to 5.3 3.5 110IMY15-05-8RG
14.4 to 36 5.1 5.07 to 5.13 10 24IMX70-05-0G
25 to 75 5.1 5.07 to 5.13 10 40IMX70-05-0G
50 to 150 5.1 5.07 to 5.13 10 110IMY70-05-0G
Continued on Next Page
Thru-Hole > Single-Output > Non-Brick
BWS
1.25 X 0.80 X 0.52 inch
31.8 X 20.3 X 13.2 mm
DFC6
2.00 x 1.00 x 0.45 inch
50.8 x 25.4 x 11.4 mm
DSP1
0.77 x 0.40 x 0.27 inch
19.6 x 10.2 x 6.9 mm
DFC15
2.02 x 1.62 x 0.55 inch
51.3 x 41.2 x 13.8 mm
DGP12
2.02 x 2.02 x 0.45 inch
51.3 x 51.3 x 11.4 mm
11
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Single Output
Alpha-sorted graphics and
dimensions augment model
listings from both pages.
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with 7 to 9Vout, Sorted by Max Amps
4.5 to 5.5 7 N/A 0.1 DSP1N5S7
Models with 12Vout, Sorted by Max Amps
4.5 to 5.5 12 N/A 0.08 DSP1N5S12
8.4 to 36 12 N/A 0.3 20IMX4-12-8
16.8 to 75 12 N/A 0.3 40IMX4-12-8
36 to 75 12 N/A 0.5 48IMS6-12-9
20 to 60 12 11.4 to 12.6 1.2 DFC15U48S12
50 to 150 12 9 to 12.6 1.4 110IMY15-12-12-8
10 to 20 12 10.8 to 13.2 2.1 OWS1212
14.4 to 36 12 11.94 to 12.06 5.8 24IMX70-12-0G
25 to 75 12 11.94 to 12.06 5.8 40IMX70-12-0G
50 to 150 12 11.94 to 12.06 5.8 110IMY70-12-0G
Models with 14 to 15Vout, Sorted by Max Amps
4.5 to 5.5 14 N/A 0.07 DSP1N5S14
4.7 to 5.5 15 N/A 0.07 DSP1N5S15
8.4 to 36 15 N/A 0.3 20IMX4-15-8
16.8 to 75 15 N/A 0.3 40IMX4-15-8
40 to 121 15 N/A 0.3 70IMX4-15-8
36 to 75 15 N/A 0.4 48IMS6-15-9
50 to 150 15 11.2 to 15.8 1.2 110IMY15-15-15-8
Model with 17 to 24Vout
4.5 to 5.5 17 N/A 0.06 DSP1N5S17
Thru-Hole > Single-Output > Non Brick
IMX15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
IMY15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
IMX4
1.30 x 0.79 x 0.33 inch
33.0 x 20.1 x 8.5 mm
IMX7
2.00 x 1.00 x 0.42 inch
50.8 x 25.4 x 10.5 mm
IMS15
2.00 x 1.60 x 0.41 inch
50.8 x 40.6 x 10.5 mm
IMS6
1.3 x 0.79 x 0.33 inch
33 x 20 x 8.5 mm
IMX70
3.00 x 2.50 x 0.50 inch
76.2 x 63.5 x 12.5 mm
IMY70
3.00 x 2.50 x 0.50 inch
76.2 x 63.5 x 12.5 mm
OWS
2.00 x 2.00 x 0.50 inch
50.8 x 50.8 x 12.7 mm
12
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Dual Output
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 72 1.8 1.6 to 2 15 60 HLD15ZEB
3.3 3 to 3.6 15
34 to 75 3.3 3 to 3.6 15 60 HBD060ZGE-A
5 4.5 to 5.5 12
Thru-Hole > Dual-Output > 1/2 Brick
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 +1.2 1.1 to 1.3 15 68 QD48T012033
+3.3 3 to 3.6 15
36 to 75 +1.5 1.4 to 1.7 15 50 QD48T015018
+1.8 1.6 to 2 15
36 to 75 +1.8 1.6 to 2 15 65 QD48T018025
+2.5 2.3 to 2.8 15
36 to 75 +1.8 1.6 to 2 15 77 QD48T018033
+3.3 3 to 3.6 15
36 to 75 +2.5 2.3 to 2.8 15 87 QD48T025033
+3.3 3 to 3.6 15
36 to 75 +3.3 3 to 3.6 15 100 QD48T033050
+5 4.5 to 5.5 10
Thru-Hole > Dual-Output > 1/4 Brick
QD48T products provide two independently-regulated high-current
outputs and, in many applications, can replace two single output
quarter-bricks.
• Low-profile heights, with no heat sink required, minimize
airflow shadowing, enhancing cooling for downstream devices.
• Capability to start-up into pre-biased loads.
• Rugged design withstands 100 V input transient for 100 ms.
• Industry-standard footprints, pinouts, and trim equations.
• Meets Basic insulation requirements of EN60950.
• Also available in SMT packages; QD48S Series.
High-Current QD48T Products Can Replace Two Single-Output Quarter-Bricks
2.30 x 1.45 x 0.28 inch
58.4 x 36.8 x 7.2 mm
Independently-Regulated
Outputs
Minimal Cross-Channel
Interference
QD48T
2.40 x 2.28 x 0.50 inch
61.0 x 57.9 x 12.7 mm
HBD
2.40 x 2.28 x 0.50 inch
61.0 x 57.9 x 12.7 mm
HLD
13
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Dual Output
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with 3.3V and 5.1V Outputs, Sorted by Watts
8.4 to 36 +3.3 2.5 to 3.5 1.4 11.3 20IMX15-0503-8R
+5.1 3.8 to 5.4 1.4
16.8 to 75 +3.3 2.5 to 3.5 1.5 12.6 40IMX15-0503-8R
+5.1 3.8 to 5.4 1.5
50 to 150 +3.3 2.5 to 3.5 1.5 12.6 110IMY15-0503-8R
+5.1 3.8 to 5.3 1.5
14 to 36 +3.3 2.5 to 3.5 1.6 13.5 24IMS15-0503-9R
+5.1 3.8 to 5.4 1.6
36 to 75 +3.3 2.5 to 3.5 1.6 13.5 48IMS15-0503-9R
+5.1 3.8 to 5.4 1.6
32 to 75 +3.3 3 to 3.6 4.2 30 48IMS30-0503-9G
+5.1 4.6 to 5.6 3.1
Models with 5V Both Outputs, Sorted by Watts
4.5 to 5.5 +5 N/A 0.07 0.8 DSP1N5D5
-5 N/A 0.07
8.4 to 36 +5 N/A 0.3 3.5 20IMX4-0505-8
-5 N/A 0.3
16.8 to 75 +5 N/A 0.3 3.5 40IMX4-0505-8
-5 N/A 0.3
40 to 121 +5 N/A 0.3 3.5 70IMX4-0505-8
-5 N/A 0.3
18 to 36 +5 N/A 0.5 5 24IMS6-0505-9
-5 N/A 0.5
8.4 to 36 5 3.8 to 5.2 0.6 6 20IMX7-05-05-8
5 3.8 to 5.2 0.6
16.8 to 75 5 3.8 to 5.2 0.7 7 40IMX7-05-05-8
5 3.8 to 5.2 0.7
40 to 121 5 3.8 to 5.2 0.7 7 70IMX7-05-05-8
5 3.8 to 5.2 0.7
60 to 150 5 3.8 to 5.2 0.7 7 110IMX7-05-05-8
5 3.8 to 5.2 0.7
8.4 to 36 5 3.8 to 5.3 1.3 13 20IMX15-05-05-8
5 3.8 to 5.3 1.3
14 to 36 5 3.8 to 5.3 1.4 14 24IMS15-05-05-9
5 3.8 to 5.3 1.4
16.8 to 75 5 3.8 to 5.3 1.4 14 40IMX15-05-05-8
5 3.8 to 5.3 1.4
36 to 75 5 3.8 to 5.3 1.4 14 48IMS15-05-05-9
5 3.8 to 5.3 1.4
50 to 150 5 3.8 to 5.2 1.4 14 110IMY15-05-05-8
5 3.8 to 5.2 1.4
Thru-Hole > Dual-Output > Non-Brick
IMS6
1.3 x 0.79 x 0.33 inch
33 x 20 x 8.5 mm
IMS15
2.00 x 1.60 x 0.41 inch
50.8 x 40.6 x 10.5 mm
DSP1
0.77 x 0.40 x 0.27 inch
19.6 x 10.2 x 6.9 mm
IMS30
2.00 x 2.00 x 0.37 inch
50.8 x 50.8 x 9.4 mm
IMX4
1.30 x 0.79 x 0.33 inch
33.0 x 20.1 x 8.5 mm
IMX7
2.00 x 1.00 x 0.42 inch
50.8 x 25.4 x 10.5 mm
IMX15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
IMY15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
14
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Dual Output
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with 12V Both Outputs, Sorted by Watts
4.5 to 5.5 +12 N/A 0.04 1 DSP1N5D12
-12 N/A 0.04
8.4 to 36 +12 N/A 0.2 4 20IMX4-1212-8
-12 N/A 0.2
16.8 to 75 +12 N/A 0.2 4 40IMX4-1212-8
-12 N/A 0.2
8.4 to 36 12 9 to 12.6 0.2 6 20IMX7-12-12-8
12 9 to 12.6 0.2
18 to 36 +12 N/A 0.2 6 24IMS6-1212-9
-12 N/A 0.2
16.8 to 75 12 9 to 12.6 0.3 7 40IMX7-12-12-8
12 9 to 12.6 0.3
40 to 121 12 9 to 12.6 0.3 7 70IMX7-12-12-8
12 9 to 12.6 0.3
60 to 150 12 9 to 12.6 0.3 7 110IMX7-12-12-8
12 9 to 12.6 0.3
8.4 to 36 12 9 to 12.6 0.7 15.6 20IMX15-12-12-8
12 9 to 12.6 0.7
16.8 to 75 12 9 to 12.6 0.7 16.8 40IMX15-12-12-8
12 9 to 12.6 0.7
36 to 75 12 9 to 12.6 0.7 16.8 48IMS15-12-12-9
12 9 to 12.6 0.7
50 to 150 12 9 to 12.6 0.7 16.8 110IMY15-12-12-8
12 9 to 12.6 0.7
Model with 14V Both Outputs
4.5 to 5.5 +14 N/A 0.04 1 DSP1N5D14
-14 N/A 0.04
Models with 15V Both Outputs, Sorted by Watts
8.4 to 36 +15 N/A 0.1 4.2 20IMX4-1515-8
-15 N/A 0.1
16.8 to 75 +15 N/A 0.1 4.2 40IMX4-1515-8
-15 N/A 0.1
8.4 to 36 15 11.2 to 15.8 0.2 6 20IMX7-15-15-8
15 11.2 to 15.8 0.2
16.8 to 75 15 11.2 to 15.8 0.2 7 40IMX7-15-15-8
15 11.2 to 15.8 0.2
40 to 121 15 11.2 to 15.8 0.2 7 70IMX7-15-15-8
15 11.2 to 15.8 0.2
60 to 150 15 11.2 to 15.8 0.2 7 110IMX7-15-15-8
15 11.2 to 15.8 0.2
3.5 to 16 +15 13.5 to 16.5 0.4 12 DGP12U5D15
-15 13.5 to 16.5 0.4
8.4 to 36 15 11.3 to 15.8 0.5 15 20IMX15-15-15-8
15 11.3 to 15.8 0.5
14 to 36 15 11.3 to 15.8 0.6 16.8 24IMS15-15-15-9
15 11.3 to 15.8 0.6
16.8 to 75 15 11.3 to 15.8 0.6 16.8 40IMX15-15-15-8
15 11.3 to 15.8 0.6
36 to 75 15 11.3 to 15.8 0.6 16.8 48IMS15-15-15-9
15 11.3 to 15.8 0.6
50 to 150 15 11.2 to 15.8 0.6 16.8 110IMY15-15-15-8
15 11.2 to 15.8 0.6
Thru-Hole > Dual-Output > Non-Brick
IMX15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
IMY15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
DGP12
2.02 x 2.02 x 0.45 inch
51.3 x 51.3 x 11.4 mm
DSP1
0.77 x 0.40 x 0.27 inch
19.6 x 10.2 x 6.9 mm
IMX7
2.00 x 1.00 x 0.42 inch
50.8 x 25.4 x 10.5 mm
IMS6
1.3 x 0.79 x 0.33 inch
33 x 20 x 8.5 mm
IMS15
2.00 x 1.60 x 0.41 inch
50.8 x 40.6 x 10.5 mm
IMX4
1.25 x 0.8 x 0.33 inch
32 x 20 x 8.5 mm
15
Isolated DC-DC > Thru-Hole > Dual Output
Unsigned output voltages are isolated and can be used as either + or - polarities.
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with 15V Both Outputs, Sorted by Watts (Continued)
Model with 17V Both Outputs
4.5 to 5.5 +17 N/A 0.03 1 DSP1N5D17
-17 N/A 0.03
Models with 24V Both Outputs, Sorted by Watts
8.4 to 36 +24 N/A 0.08 3.8 20IMX4-2424-8
-24 N/A 0.08
16.8 to 75 +24 N/A 0.08 3.8 40IMX4-2424-8
-24 N/A 0.08
8.4 to 36 24 18 to 25.2 0.1 6 20IMX7-24-24-8
24 18 to 25.2 0.1
16.8 to 75 24 18 to 25.2 0.1 7 40IMX7-24-24-8
24 18 to 25.2 0.1
40 to 121 24 18 to 25.2 0.1 7 70IMX7-24-24-8
24 18 to 25.2 0.1
60 to 150 24 18 to 25.2 0.1 7 110IMX7-24-24-8
24 18 to 25.2 0.1
8.4 to 36 24 18 to 25.2 0.3 15.4 20IMX15-24-24-8
24 18 to 25.2 0.3
14 to 36 24 18 to 25.2 0.3 16.8 24IMS15-24-24-9
24 18 to 25.2 0.3
16.8 to 75 24 18 to 25.2 0.3 16.8 40IMX15-24-24-8
24 18 to 25.2 0.3
36 to 75 24 18 to 25.2 0.3 16.8 48IMS15-24-24-9
24 18 to 25.2 0.3
50 to 150 24 18 to 25.2 0.3 16.8 110IMY15-24-24-8
24 18 to 25.2 0.3
Thru-Hole > Dual-Output > Non-Brick
IMX15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
IMY15
2.00 x 1.50 x 0.42 inch
50.8 x 38.1 x 10.7 mm
DSP1
0.77 x 0.40 x 0.27 inch
19.6 x 10.2 x 6.9 mm
IMX7
2.00 x 1.00 x 0.42 inch
50.8 x 25.4 x 10.5 mm
IMS15
2.00 x 1.60 x 0.41 inch
50.8 x 40.6 x 10.5 mm
IMX4
1.25 x 0.8 x 0.33 inch
32 x 20 x 8.5 mm
16
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Triple Output
IMX35
3.00 x 2.50 x 0.41 inch
76.2 x 63.5 x 10.4 mm
1500 VDC Isolation
Extremely Wide Input Voltage
Ranges
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Three 5V Outputs, Sorted by Input Voltage
9 to 36 5 4.2 to 5.2 1.4 35 20IMX35D05D05-8
5 4.2 to 5.2 1.4
5 4.2 to 5.2 2.7
18 to 75 5 4.2 to 5.2 1.4 35 40IMX35D05D05-8
5 4.2 to 5.2 1.4
5 4.2 to 5.2 2.8
40 to 121 5 4.2 to 5.2 1.4 35 70IMX35D05D05-8
5 4.2 to 5.2 1.4
5 4.2 to 5.2 2.8
60 to 150 5 4.2 to 5.2 1.4 35 110IMX35D05D05-8
5 4.2 to 5.2 1.4
5 4.2 to 5.2 2.8
Models with Two 5V and One 12V Output, Sorted by Input Voltage
9 to 36 5 4.2 to 5.2 1.4 35 20IMX35D05D12-8
5 4.2 to 5.2 1.4
12 10.2 to 12.6 1.3
18 to 75 5 4.2 to 5.2 1.4 35 40IMX35D05D12-8
5 4.2 to 5.2 1.4
12 10.2 to 12.6 1.4
40 to 121 5 4.2 to 5.2 1.4 35 70IMX35D05D12-8
5 4.2 to 5.2 1.4
12 10.2 to 12.6 1.4
60 to 150 5 4.2 to 5.2 1.4 35 110IMX35D05D12-8
5 4.2 to 5.2 1.4
12 10.2 to 12.6 1.4
Models with Two 5V and One 15V Output, Sorted by Input Voltage
9 to 36 5 4.2 to 5.2 1.4 35 20IMX35D05D15-8
5 4.2 to 5.2 1.4
15 12.8 to 15.8 1.1
18 to 75 5 4.2 to 5.2 1.4 35 40IMX35D05D15-8
5 4.2 to 5.2 1.4
15 12.8 to 15.8 1.2
40 to 121 5 4.2 to 5.2 1.4 35 70IMX35D05D15-8
5 4.2 to 5.2 1.4
15 12.8 to 15.8 1.2
60 to 150 5 4.2 to 5.2 1.4 35 110IMX35D05D15-8
5 4.2 to 5.2 1.4
15 12.8 to 15.8 1.2
IMX35 outputs can be paralleled and stacked to provide additional voltage/current
combinations. Please download the IMX35 data sheet for further details.
Thru-Hole > Triple-Output > Non-Brick
17
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Triple Output
DGP20
2.02 x 2.02 x 0.45 inch
51.3 x 51.3 x 11.4 mm
IMX35
3.00 x 2.50 x 0.41 inch
76.2 x 63.5 x 10.4 mm
1500 VDC Isolation
Extremely Wide Input Voltage
Ranges
Triple-output configurations
of this quad-output series
utilize two outputs in parallel
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with One 5V and Two 12V Outputs, Sorted by Watts
9 to 36 5 4.2 to 5.2 2.7 35 20IMX35D05D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
18 to 75 5 4.2 to 5.2 2.8 35 40IMX35D05D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
40 to 121 5 4.2 to 5.2 2.8 35 70IMX35D05D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
60 to 150 5 4.2 to 5.2 2.8 35 110IMX35D05D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
Models with One 5V and Two 15V Outputs, Sorted by Watts
18 to 36 +5 N/A 2.5 20 DGP20E24T5/15
+15 N/A 0.2
-15 N/A 0.2
9 to 36 5 4.2 to 5.2 2.7 35 20IMX35D05D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
18 to 75 5 4.2 to 5.2 2.8 35 40IMX35D05D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
40 to 121 5 4.2 to 5.2 2.8 35 70IMX35D05D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
60 to 150 5 4.2 to 5.2 2.8 35 110IMX35D05D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
Continued on Next Page
Thru-Hole > Triple-Output > Non-Brick
18
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Triple & Quad Output
IMX35
3.00 x 2.50 x 0.41 inch
76.2 x 63.5 x 10.4 mm
1500 VDC Isolation
Extremely Wide Input Voltage
Ranges
Independent Outputs Can Be
Used in Series or Parallel
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Three 12V Outputs, Sorted by Input Voltage
9 to 36 12 10.2 to 12.6 0.7 35 20IMX35D12D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 1.3
18 to 75 12 10.2 to 12.6 0.7 35 40IMX35D12D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 1.4
40 to 121 12 10.2 to 12.6 0.7 35 70IMX35D12D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 1.4
60 to 150 12 10.2 to 12.6 0.7 35 110IMX35D12D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 1.4
Models with Three 15V Outputs, Sorted by Input Voltage
9 to 36 15 12.8 to 15.8 0.6 35 20IMX35D15D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 1.1
18 to 75 15 12.8 to 15.8 0.6 35 40IMX35D15D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 1.2
40 to 121 15 12.8 to 15.8 0.6 35 70IMX35D15D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 1.2
60 to 150 15 12.8 to 15.8 0.6 35 110IMX35D15D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 1.2
Thru-Hole > Triple-Output > Non-Brick
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Four 5V Outputs, Sorted by Input Voltage
9 to 36 5 4.2 to 5.2 1.35 27 20IMX35D05D05-8
5 4.2 to 5.2 1.35
5 4.2 to 5.2 1.35
5 4.2 to 5.2 1.35
18 to 75 5 4.2 to 5.2 1.4 28 40IMX35D05D05-8
5 4.2 to 5.2 1.4
5 4.2 to 5.2 1.4
5 4.2 to 5.2 1.4
40 to 121 5 4.2 to 5.2 1.4 28 70IMX35D05D05-8
5 4.2 to 5.2 1.4
5 4.2 to 5.2 1.4
5 4.2 to 5.2 1.4
60 to 150 5 4.2 to 5.2 1.4 28 110IMX35D05D05-8
5 4.2 to 5.2 1.4
5 4.2 to 5.2 1.4
5 4.2 to 5.2 1.4
Thru-Hole > Quad-Output > Non-Brick
19
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Quad Output
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Two 5V and Two 12V Outputs, Sorted by Input Voltage
9 to 36 5 4.2 to 5.2 1.35 29 20IMX35D05D12-8
12 10.2 to 12.6 0.65
12 10.2 to 12.6 0.65
5 4.2 to 5.2 1.35
18 to 75 5 4.2 to 5.2 1.4 30 40IMX35D05D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
5 4.2 to 5.2 1.4
40 to 121 5 4.2 to 5.2 1.4 30 70IMX35D05D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
5 4.2 to 5.2 1.4
60 to 150 5 4.2 to 5.2 1.4 30 110IMX35D05D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
5 4.2 to 5.2 1.4
Models with Two 5V and Two 15V Outputs, Sorted by Input Voltage
9 to 36 5 4.2 to 5.2 1.35 30 20IMX35D05D15-8
15 12.8 to 15.8 0.55
15 12.8 to 15.8 0.55
5 4.2 to 5.2 1.35
18 to 75 5 4.2 to 5.2 1.4 32 40IMX35D05D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
5 4.2 to 5.2 1.4
40 to 121 5 4.2 to 5.2 1.4 32 70IMX35D05D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
5 4.2 to 5.2 1.4
60 to 150 5 4.2 to 5.2 1.4 32 110IMX35D05D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
5 4.2 to 5.2 1.4
Models with Four 12V Outputs, Sorted by Input Voltage
9 to 36 12 10.2 to 12.6 0.65 31 20IMX35D12D12-8
12 10.2 to 12.6 0.65
12 10.2 to 12.6 0.65
12 10.2 to 12.6 0.65
18 to 75 12 10.2 to 12.6 0.7 34 40IMX35D12D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
40 to 121 12 10.2 to 12.6 0.7 34 70IMX35D12D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
60 to 150 12 10.2 to 12.6 0.7 34 110IMX35D12D12-8
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
12 10.2 to 12.6 0.7
Thru-Hole > Quad-Output > Non-Brick
IMX35
3.00 x 2.50 x 0.41 inch
76.2 x 63.5 x 10.4 mm
1500 VDC Isolation
Extremely Wide Input Voltage
Ranges
Independent Outputs Can Be
Used in Series or Parallel
20
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > Thru-Hole > Quad Output
IMX35
3.00 x 2.50 x 0.41 inch
76.2 x 63.5 x 10.4 mm
1500 VDC Isolation
Extremely Wide Input Voltage
Ranges
Independent Outputs Can Be
Used in Series or Parallel
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Four 15V Outputs, Sorted by Input Voltage
9 to 36 15 12.8 to 15.8 0.55 33 20IMX35D15D15-8
15 12.8 to 15.8 0.55
15 12.8 to 15.8 0.55
15 12.8 to 15.8 0.55
18 to 75 15 12.8 to 15.8 0.6 35 40IMX35D15D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
40 to 121 15 12.8 to 15.8 0.6 35 70IMX35D15D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
60 to 150 15 12.8 to 15.8 0.6 35 110IMX35D15D15-8
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
15 12.8 to 15.8 0.6
Thru-Hole > Input Filters
Max Max Input
Current Voltage Meets
(Amps) (VDC) Mounting Conducted Part Number
5 100 Through-Hole FCC Class B FC100V5A
10 100 Through-Hole FCC Class B FC100V10A
20 100 Through-Hole FCC Class B FC100V20A
Thru-Hole > Quad-Output > Non-Brick
21
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > SMT > Single-Output
2.30 x 0.90 x 0.26 inch
58.4 x 22.8 x 6.6 mm
SQ48S
SQ24S
2.30 x 0.90 x 0.26 inch
58.4 x 22.8 x 6.6 mm
SQM48S
2.30 x 0.90 x 0.28 inch
58.4 x 22.8 x 7.1 mm
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with Nominal 24Vin, Sorted by Factory Set Vout
18 to 36 5 4 to 5.5 10 SQ24S10050
18 to 36 6 4.8 to 6.6 8 SQ24S08060
18 to 36 12 9.6 to 13.2 4 SQ24S04120
19 to 36 15 12 to 16.5 3.3 SQ24S03150
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 1.2 1.1 to 1.3 15 SQ48S15012
36 to 75 1.5 1.2 to 1.6 15 SQ48S15015
36 to 75 1.8 1.5 to 1.9 15 SQ48S15018
36 to 75 2 1.6 to 2.2 15 SQ48S15020
36 to 75 2.5 2 to 2.7 15 SQ48S15025
36 to 75 3.3 2.7 to 3.6 15 SQ48S15033
36 to 75 3.3 2.7 to 3.6 20 SQM48S20033
36 to 75 5 4 to 5.5 10 SQ48S10050
36 to 75 6 4.8 to 6.6 8 SQ48S08060
SMT > Single-Output > 1/8 Brick
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with Nominal 24Vin, Sorted by Factory Set Vout
18 to 36 3.3 2.7 to 3.6 30 Q24S30033
18 to 36 5 4 to 5.5 15 Q24S15050
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 1.2 1.1 to 1.3 30 QL48S30012
36 to 75 1.5 1.2 to 1.6 25 Q48S25015
36 to 75 1.5 1.2 to 1.6 30 Q48S30015
36 to 75 1.8 1.5 to 1.9 25 Q48S25018
36 to 75 1.8 1.5 to 1.9 30 Q48S30018
36 to 75 2 1.6 to 2.2 25 Q48S25020
36 to 75 2 1.6 to 2.2 30 Q48S30020
36 to 75 2.5 2 to 2.7 25 Q48S25025
36 to 75 2.5 2 to 2.7 30 Q48S30025
36 to 75 3.3 2.7 to 3.6 25 Q48S25033
36 to 75 5 4 to 5.5 15 Q48S15050
36 to 75 12 9.6 to 13.2 8 Q48S08120
SMT > Single-Output > 1/4 Brick
QM48S
QL48S
Q24S & Q48S
2.30 x 1.45 x 0.26 inch
58.4 x 36.8 x 6.6 mm
2.30 x 1.45 x 0.28 inch
58.4 x 36.8 x 7.1 mm
2.30 x 1.45 x 0.26 inch
58.4 x 36.8 x 6.6 mm
22
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > SMT > Single-Output & Dual Output
SMT > Single-Output > Non-Brick
1.30 x 0.81 x 0.33 inch
33 x 20.6 x 8.5 mm
NVS
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
Models with 9 to 36Vin, Sorted by Factory Set Vout
9 to 36 3.3 N/A 0.9 NVS0.9CE-M6
9 to 36 5 N/A 0.7 NVS0.7CG-M6
9 to 36 12 N/A 0.3 NVS0.3CH-M6
9 to 36 15 N/A 0.3 NVS0.3CJ-M6
Models with 18 to 36Vin, Sorted by Factory Set Vout
18 to 36 5 N/A 1 NVS01YG-M6
18 to 36 12 N/A 0.5 NVS0.5YH-M6
18 to 36 15 N/A 0.4 NVS0.4YJ-M6
Models with Ultra-Wide Input, Sorted by Factory Set Vout
18 to 75 3.3 N/A 0.9 NVS0.9EE-M6
18 to 75 5 N/A 0.7 NVS0.7EG-M6
18 to 75 12 N/A 0.3 NVS0.3EH-M6
18 to 75 15 N/A 0.3 NVS0.3EJ-M6
Models with Nominal 48Vin and 1.5 to 15Vout, Sorted by Factory Set Vout
36 to 75 5 N/A 1 NVS01ZG-M6
36 to 75 5 4.5 to 5.5 2 NDS02ZG-M6
36 to 75 12 N/A 0.5 NVS0.5ZH-M6
36 to 75 15 N/A 0.4 NVS0.4ZJ-M6
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 +1.8 1.6 to 2 15 77 QD48S018033
+3.3 3 to 3.6 15
36 to 75 +1.8 1.6 to 2 15 77 QD48S018050
+5 4.5 to 5.5 10
36 to 75 +3.3 3 to 3.6 15 100 QD48S033050
+5 4.5 to 5.5 10
SMT > Dual-Output > 1/4 Brick
QD48S products provide two independently-regulated high-current
outputs and, in many applications, can replace two single-output
quarter-bricks.
• Low-profile heights, with no heat sink required, minimize
airflow shadowing, enhancing cooling for downstream devices.
• Capability to start-up into pre-biased loads.
• Rugged design withstands 100 V input transient for 100 ms.
• Industry-standard footprints, pinouts, and trim equations.
• Meets Basic insulation requirements of EN60950.
• Also available in through-hole packages; QD48T Series.
High-Current QD48S Products Can Replace Two Single-Output Quarter-Bricks
2.30 x 1.45 x 0.26 inch
58.4 x 36.8 x 6.6 mm
QD48S
23
Unsigned output voltages are isolated and can be used as either + or - polarities.
Isolated DC-DC > SMT > Dual-Output
Input Factory Output Max
Voltage Set Vout Trim Range Amps Watts Model
Models with 9 to 36Vin, Sorted by Factory Set Vout
9 to 36 +5 N/A 0.3 3.5 NVD0.7CGG-M6
-5 N/A 0.3
9 to 36 +12 N/A 0.2 4 NVD0.3CHH-M6
-12 N/A 0.2
9 to 36 +15 N/A 0.1 4.2 NVD0.3CJJ-M6
-15 N/A 0.1
9 to 36 +24 N/A 0.1 3.8 NVD0.2CKK-M6
-24 N/A 0.1
Models with 18 to 36Vin, Sorted by Factory Set Vout
18 to 36 +5 N/A 0.5 5 NVD01YGG-M6
-5 N/A 0.5
18 to 36 +12 N/A 0.2 6 NVD0.5YHH-M6
-12 N/A 0.2
18 to 36 +15 N/A 0.2 6 NVD0.4YJJ-M6
-15 N/A 0.2
Models with Ultra-Wide Input, Sorted by Factory Set Vout
18 to 75 +5 N/A 0.3 3.5 NVD0.7EGG-M6
-5 N/A 0.3
18 to 75 +12 N/A 0.2 4 NVD0.3EHH-M6
-12 N/A 0.2
18 to 75 +15 N/A 0.1 4.2 NVD0.3EJJ-M6
-15 N/A 0.1
18 to 75 +24 N/A 0.1 3.8 NVD0.2EKK-M6
-24 N/A 0.1
Models with Nominal 48Vin, Sorted by Factory Set Vout
36 to 75 +5 N/A 0.5 5 NVD01ZGG-M6
-5 N/A 0.5
36 to 75 +12 N/A 0.2 6 NVD0.5ZHH-M6
-12 N/A 0.2
36 to 75 +15 N/A 0.2 6 NVD0.4ZJJ-M6
-15 N/A 0.2
SMT > Input Filters
Max Max Input
Current Voltage Meets
(Amps) (VDC) Mounting Conducted Part Number
4 80 SMT FCC Class B F4804A
10 50 SMT FCC Class B F2410
10 100 SMT FCC Class B F4810
SMT > Dual-Output > Non-Brick
NVD
1.30 x 0.81 x 0.33 inch
33.0 x 20.6 x 8.5 mm
24
www.power-one.com
THIS PAGE INTENTIONALLY LEFT BLANK.
25
Unsigned output voltages are isolated and can be used as either + or - polarities.
Rack-Mount Front Ends > Single Output
Nominal Max Vin Output Standby Power Mating
Vout Amps Range Trim Range Vout Supply Shelves
31 85 to 264 VAC 44.2 to 51.8V 12V FXP1500-48G FXR-3-48
37.5 85 to 264 VAC 44.2 to 51.8V 12V FXP1800-48G FXR-3-48
48V 125 180 to 264 or 45.6 to 50.4V 12V FXP6000-48-S NLA*
342 to 528 VAC
145 180 to 264 or 45.6 to 50.4V 12V FXP7000-48-S NLA*
342 to 528 VAC
FXP1500/1800
12 x 5.6 x 1.6 inch
304.8 x 142.2 x 40.6 mm
FXP6000/7000
16.96 x 8 x 5 inch
430.8 x 203.2 x 127 mm
Backplane-Mounted Input Connector - AC-DC
Current-share for up to 30 units
Suitable for 3U or 5U height
monitoring
Advanced topologies deliver up to
90% efficiency.
High density design: up to 14 W/in3
Power-One offers a broad array of DPA& IBAhot-swap front ends.
Chassis-mount front ends are also available and are listed in the
Chassis Mount > Single Output section. Power-One’s hot-swap
products combine high-efficiency topologies with advanced
thermal management techniques to provide industry-leading
power densities. Additional features include:
• Extensive I2C interface monitoring & control capabilities
• Active current share with ORing FETs
• Compact, low-profile packages that fit 1U-height constraints
* Shelves No Longer Available
26
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Rack-Mount Front Ends > Single Output
SFD550 SFP450/650/1050
12.4 x 3.1 x 1.6 inch
314.5 x 78 x 40 mm
Common form factor AC and DC input products
Status LEDs: Input OK, Output OK, and Fault
FNP600/850/1000
11.74 x 3.3 x 1.6 inch
298.2 x 83.8 x 40.6 mm
FND850
12.4 x 3.38 x 1.6 inch
315 x 86 x 41 mm
SFD1200-12BG
11.42 x 3.07 x 1.57 inch
290 x 78 x 40 mm
SGP1200-12G
11.0 x 3.2 x 1.57 inch
279 x 81 x 40 mm
Droop current share with ORing FETs
Can be used in hot-swap redundant systems
Control available via GUI-driven I2C software
Nominal Max Vin Output Standby Power Mating
Vout Amps Range Trim Range Vout Supply Shelves
25 85 to 264 VAC N/A 12V FNP300-1012 N/A
25 40.5 to 72 VDC N/A N/A FND300-1012G N/A
36.6 90 to 264 VAC N/A 3.3V SFP450-12BG N/A
45 -40 to -75 VDC N/A 3.3V SFD550-12BG N/A
50 90 to 264 VAC 7 to 12V 12V FNP600-12 FNR-5-12
53.3 90 to 264 VAC N/A 3.3V SFP650-12BG N/A
12V 71 36 to 75 VDC 7 to 12V 12V FND850-12RG N/A
71 36 to 75 VDC 7 to 12.3V 12V FND850-12DRG N/A
73 90 to 264 VAC 7 to 12V 12V FNP850-12 FNR-5-12
86.7 90 to 264 VAC N/A 3.3V SFP1050-12BG N/A
93.3 90 to 264 VAC N/A 3.3V SGP1200-12G N/A
93.3 90 to 264 VAC N/A 3.3V SGP1200-12RG N/A
99.2 -40 to -75 VDC N/A 3.35V SFD1200-12BG N/A
125 85 to 264 VAC 7 to 13V 12V FNP1500-12G FNR-3-12
24V 12.5 85 to 264 VAC N/A 12V FNP300-1024 N/A
6.2 85 to 264 VAC N/A 12V FNP300-1048 N/A
48V 21 90 to 264 VAC N/A 12V FNP1000-48 FNR-5-48
31 85 to 264 VAC 44.2 to 51.8V 12V FNP1500-48G FNR-3-48G
37.5 85 to 264 VAC 44.2 to 51.8V 12V FNP1800-48G FNR-3-48G
Front-Mounted Input Receptacle - AC-DC & DC-DC
27
Vout Max Input Power Max # of
Nominal Amps Range Shelf Height Width Depth Supply Supplies
250 85 to 264 VAC FNR-5-12 1U 19” 13” FNP600-12 5
12V 355 85 to 264 VAC FNR-5-12 1U 19” 13” FNP850-12 5
375 85 to 264 VAC FNR-3-12 1U 19” 13” FNP1500-12G 3
62 85 to 264 VAC FNR-5-48 1U 19” 13” FNP600-48 5
93 85 to 264 VAC FNR-3-48 1U 19” 13” FNP1500-48G 3
48V 93 85 to 264 VAC FXR-3-48 1U 19” 13” FXP1500-48G 3
105 85 to 264 VAC FNR-5-48 1U 19” 13” FNP1000-48 5
112 85 to 264 VAC FNR-3-48 1U 19” 13” FNP1800-48 3
112 85 to 264 VAC FXR-3-48 1U 19” 13” FXP1800-48G 3
AC-DC Power Shelves
• Up to 375 Amps per shelf configuration
• Shelves may be partially populated for reduced
currents, or paralleled for higher currents.
Rack-Mount Front Ends > Single Output
Rack-Mount Power Shelves
FND300
FNP300
8.5 x 4.0 x 1.65 inch
215.9 x 101.6 x 41.9 mm
FNP1500/1800
11 x 5.6 x 1.6 inch
279.4 x 141.2 x 40.6 mm
Common form factor AC and DC input products
Overtemperature, output overvoltage, and output
overcurrent protections
High power densities, up to 18.3 W/in3
I2C voltage and current limit setting
Analog output voltage setting
Front-Mounted Input Receptacle - AC-DC & DC-DC
28
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Chassis Mount > AC-DC
MAP40
FXC6000/7000
15.17 x 8 x 5 inch
38.5 x 20.3 x 12.7 cm
5.00 x 3.00 x 1.16 inch
127.0 x 76.2 x 29.5 mm
MAP80
7.20 x 4.20 x 1.80 inch
182.9 x 106.7 x 45.7 mm
MAP130
8.50 x 4.50 x 2.00 inch
215.9 x 114.3 x 50.8 mm
Factory Output Max Input Max
Set Vout Trim Range Amps VAC Watts Model
Models with 3.3 and 5Vout, Sorted by Vout then Max Watts
5 4.7 to 5.5 8 90 to 264 40 MAP40-1005
5 4.8 to 5.5 11 85 to 264 55 BLP55-1005
5 4.8 to 5.5 26 90 to 264 130 MAP130-1005
5 4.5 to 5.5 50 85 to 264 250 PFC250-1005
Models with 12 and 15Vout, Sorted by Vout then Max Watts
12 11.4 to 13.2 4.5 85 to 264 55 BLP55-1012
12 11.4 to 15.8 5 90 to 264 55 MAP55-1012
12 11.5 to 15.5 7.5 90 to 264 80 MAP80-1012
12 11.2 to 15.8 10 85 to 264 110 MAP110-1012
12 11.8 to 12.2 10.5 90 to 264 125 MPB125-1012
12 11.4 to 15.8 12 90 to 264 130 MAP130-1012
12 11 to 16 12.5 85 to 264 140 MAP140-1012
12 11.6 to 16 17 85 to 264 200 MPU200-1012G
12 10.8 to 13.5 21 85 to 264 250 PFC250-1012
12 10.8 to 13.5 30 85 to 264 375 PFC375-1012
15 13.5 to 18.3 17 85 to 264 250 PFC250-1015
Models with 24 and 28Vout, Sorted by Vout then Max Watts
24 22.8 to 26.4 2.3 85 to 264 55 BLP55-1024
24 23.5 to 28.5 2.5 90 to 264 55 MAP55-1024
24 23 to 29 3.8 90 to 264 80 MAP80-1024
24 22.8 to 29.2 5 85 to 264 110 MAP110-1024
24 22.5 to 30 6.2 90 to 264 130 MAP130-1024
24 22.8 to 29.2 6.3 85 to 264 140 MAP140-1024
24 22.8 to 29.2 8.3 85 to 264 200 MPU200-1024G
24 21.6 to 26.4 10.5 85 to 264 250 PFC250-1024
24 21.6 to 26.4 15 85 to 264 375 PFC375-1024
24 21.6 to 26.4 21 85 to 264 500 PFC500-1024
AC-DC > Single Output
MAP55
6.00 x 3.27 x 1.60 inch
152.4 x 83.1 x 40.6 mm
Additional single-output products are described in the Rack-Mount Front-End and
Modular Solutions sections.
BLP55
5.00 x 3.00 x 1.23 inch
127.0 x 76.2 x 31.2 mm
Factory Output Max Input Max
Set Vout Trim Range Amps VAC Watts Model
Models with 48Vout, Sorted by Max Watts
48 45 to 56 4.2 85 to 264 200 MPU200-1048G
48 46 to 56 10.4 85 to 264 500 PFC500-1048
48 45.6 to 50.4 125 180 to 528 6000 FXC6000-48-S
48 45.6 to 50.4 145 180 to 528 7000 FXC7000-48-S
AC-DC > Single Output
29
Unsigned output voltages are isolated and can be used as either + or - polarities.
Alpha-sorted graphics and
dimensions augment model
listings from both pages.
Chassis Mount > AC-DC
PFC250
PFC375/PFC500
8.50 x 4.75 x 2.00 inch
215.9 x 120.7 x 50.8 mm
9.00 x 5.00 x 2.50 inch
228.6 x 127.0 x 63.5 mm
Factory Output Max Input Max
Set Vout Trim Range Amps VAC Watts Model
Sorted by Factory Set Vout
+5 N/A 25 90 to 264 125 MPB125-2005
+12 N/A 0.5
+12 N/A 10.5 90 to 264 125 MPB125-2012
12 N/A 0.5
+12 N/A 12.5 90 to 264 150 MPB150-2012G
12 N/A 0.5
+24 N/A 6 90 to 264 150 MPB150-2024G
12 N/A 0.5
+48 N/A 2.6 90 to 264 125 MPB125-2048
12 N/A 0.5
+48 N/A 3.1 90 to 264 150 MPB150-2048G
12 N/A 0.5
AC-DC > Dual Output
MAP110/MAP140
7.00 x 4.30 inch
177.8 x 109.2 mm
MAP110: 1.97 inch height
MAP140: 1.80 inch height
MPB125/MPB150
5.00 x 3.00 x 1.25 inch
127.0 x 76.2 x 31.8 mm
MPU200
8.00 x 4.20 x 1.50 inch
203 x 107 x 38 mm
30
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Chassis Mount > AC-DC
MAP40
5.00 x 3.00 x 1.16 inch
127.0 x 76.2 x 29.5 mm
MAP140
7.00 x 4.30 x 1.80 inch
177.8 x 109.2 x 45.7 mm
MPB125
5.00 x 3.00 x 1.25 inch
127.0 x 76.2 x 31.8 mm
MPU150
8.00 x 4.20 x 1.50 inch
203.2 x 106.7 x 38.1 mm
AC-DC > Triple Output
Factory Output Max Input Max
Set Vout Trim Range Amps VAC Watts Model
One 3.3V, One 5V, and One 12V Output
+3.3 N/A 5 85 to 264 37 BLP55-3300
+5 N/A 2.5
+12 N/A 0.7
+3.3 3.1 to 3.8 35 85 to 264 150 MPU150-3300
+5 5 to 5.5 20
+12 N/A 2
Model with Two 5V and One 12V Output
+5 4.7 to 5.8 3 90 to 264 40 MAP40-3105
-5 N/A 0.5
+12 N/A 2
Models with One 5V and Two 12V Outputs, Sorted by Max Watts
+5 4.7 to 5.8 5 90 to 264 40 MAP40-3500
+12 N/A 1
-12 N/A 0.3
+5 N/A 5 85 to 264 55 BLP55-3000
+12 N/A 2.5
-12 N/A 0.7
+5 N/A 16.5 90 to 264 125 MPB125-3000
+12 N/A 5
-12 N/A 0.5
Model with One 5V, One 12V, and One 24V Output; Sorted by Max Watts
+5 4.8 to 5.2 3 90 to 264 40 MAP40-3101
+24 N/A 1
-12 N/A 0.3
Factory Output Max Input Max
Set Vout Trim Range Amps VAC Watts Model
Models Under 100 Watts, Sorted by Max Watts
+5 4.7 to 5.6 6 90 to 264 55 MAP55-4001
+24 N/A 1.5
-12 N/A 0.5
+12 N/A 0.5
+5 4.7 to 5.6 6 90 to 264 55 MAP55-4004
+24 N/A 1.5
-15 N/A 0.5
+15 N/A 0.5
+5 4.8 to 5.5 14 90 to 264 80 MAP80-4010
+12 11.5 to 12.5 4
-5 N/A 1
-12 N/A 3
+5 4.8 to 5.5 14 90 to 264 80 MAP80-4004
+24 23 to 25 2
-15 N/A 1
+15 N/A 1
Continued on Next Page
AC-DC > Quad Output
BLP55
5.00 x 3.00 x 1.23 inch
127.0 x 76.2 x 31.2 mm
31
Unsigned output voltages are isolated and can be used as either + or - polarities.
Chassis Mount > AC-DC
Factory Output Max Input Max
Set Vout Trim Range Amps VAC Watts Model
Models from 110 to 125 Watts, Sorted by Max Watts then Factory Set Vout
+5 4.8 to 5.2 12 85 to 264 110 MAP110-4000
+12 N/A 5
-12 N/A 1
-5 N/A 1
+5 4.8 to 5.2 12 85 to 264 110 MAP110-4002
+12 N/A 5
-12 N/A 1
+12 N/A 1
+5 4.8 to 5.2 12 85 to 264 110 MAP110-4004
+24 N/A 3
-15 N/A 1
+15 N/A 1
+12 11.6 to 12.4 5 85 to 264 110 MAP110-4200
+24 N/A 4
-12 N/A 1
+5 N/A 2
+3.3 N/A 10 90 to 264 125 MPB125-4350
+5 N/A 15
+12 N/A 5
-12 N/A 0.5
Models from 130 to 150 Watts, Sorted by Max Watts then Factory Set Vout
+5 4.8 to 5.5 20 90 to 264 130 MAP130-4002
+12 11.5 to 12.5 5
-12 N/A 1
+12 N/A 1
+5 4.8 to 5.5 20 90 to 264 130 MAP130-4010
+12 N/A 5
-5 N/A 1
-12 N/A 3
+5 4.8 to 5.5 20 90 to 264 130 MAP130-4003
+15 14 to 16 4
-5 N/A 1
-15 N/A 1
+5 4.8 to 5.5 20 90 to 264 130 MAP130-4001
+24 23 to 25 3.5
-12 N/A 1
+12 N/A 1
+3.3 3.1 to 3.6 30 85 to 264 150 MPU150-4350
+5 5 to 5.5 15
12 10.8 to 13.2 3
12 10.8 to 13.2 3
+5 5 to 5.5 30 85 to 264 150 MPU150-4530
+3.3 3.1 to 3.6 15
12 10.8 to 13.2 3
12 10.8 to 13.2 3
+5 5 to 5.5 30 85 to 264 150 MPU150-4000
+12 10.8 to 13.2 8
12 10.8 to 13.2 3
5 5 to 5.5 2
AC-DC > Quad Output
MAP110
7.00 x 4.30 x 1.97 inch
177.8 x 109.2 x 50 mm
Remote Sense on Main
Outputs
Optional L-Bracket & Cover
MPB125
5.00 x 3.00 x 1.25 inch
127.0 x 76.2 x 31.8 mm
High Power Density in
Industry Standard 3” x 5”
Footprint
Power Factor Correction
Meets EN61000-3-2
MAP130
8.50 x 4.50 x 2.00 inch
215.9 x 114.3 x 50.8 mm
Metric & SAE Mounting
Inserts
Power Fail Signal
MPU150
8.00 x 4.20 x 1.50 inch
203 x 107 x 38 mm
Power Factor Correction
Meets EN61000-3-2
32
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Chassis Mount > AC-DC
PFC375
9.00 x 5.00 x 2.50 inch
228.6 x 127.0 x 63.5 mm
PFC250
8.50 x 4.75 x 2.00 inch
215.9 x 120.7 x 50.8 mm
Factory Output Max Input Max
Set Vout Trim Range Amps VAC Watts Model
Models from 200 to 400 Watts, Sorted by Max Watts
+5 5 to 5.5 30 85 to 264 200 MPU200-4530
+3.3 3.1 to 3.6 15
12 10.8 to 13.2 8
12 10.8 to 13.2 4
+5 5 to 5.5 40 85 to 264 250 PFC250-4530
+3.3 3.1 to 3.5 20
12 10.8 to 13.2 6
12 10.8 to 13.2 3
+5 4.5 to 5.5 40 85 to 264 375 PFC375-4000
+12 11.3 to 12.6 10
12 11.3 to 12.6 6
5 N/A 3
+5 4.5 to 5.5 40 85 to 264 375 PFC375-4002
+12 11.3 to 12.6 10
12 11.3 to 12.6 6
24 22 to 28 3
+24 21.5 to 26.4 10 85 to 264 375 PFC375-4200
+5 4.5 to 5.5 10
12 11.4 to 12.6 4
12 11.4 to 12.6 4
+24 21.5 to 26.4 10 85 to 264 375 PFC375-4201
+5 4.5 to 5.5 10
15 14.2 to 16 4
15 13.7 to 16 4
AC-DC > Quad Output
MPU200
8.00 x 4.20 x 1.50 inch
203 x 107 x 38 mm
33
Chassis Mount > AC-DC Modular Solutions
AC-DC > LPM615 Modular Power Supply
COMING SOON...
•Standard output voltages of 2 to 54 VDC
•Efficiencies up to 88% typical
•Extra-Low 1U profile: 40.64 mm
•Leading power density of 17 Watts/cubic inch
•1 to 6 isolated outputs with full user configurability
•Power Factor Correction (PFC) IEC 61000-3-2 compliant
•1200 or 1500 Watts of total output power
•Zero-load operation
•Single-wire current sharing
•Universal input
•Individual control signals on each module
•Two-year warranty
34
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Linear Power Supplies > Single Output
Worldwide AC Input Capabilities:
100/120/220/230/240 VAC
±0.05% Output Regulation
Low Output Ripple
UL, CSA, and TÜV Approvals
Mean Time Before Failure (MTBF) in
Excess of 300,000 Hours
CE Marked to Low Voltage Directive
100% Burn-In
2-Year Warranty
Overvoltage Protection (OVP)
Standard on 5V Single Outputs;
Optional for Outputs Under 48V
Nominal Max Model Input Case Additional
Vout* Amps 100 to 264 VAC Type Features & Notes
Models with 5Vout, Sorted by Max Amps
5 1.5 HA5-1.5/OVP-AG B A
5 3 HB5-3/OVP-AG B A, C
5 6 HC5-6/OVP-AG C A, C
5 9 HN5-9/OVP-AG N A, C
5 12 HD5-12/OVP-AG D A, C
5 18 HE5-18/OVP-AG E A, C
5 25 F5-25/OVP-AG F A, C, D, H
5 35 G5-35/OVP-AG F A, C, D, H
Models with 12 to 15Vout, Sorted by Vout then Max Amps
12 0.9 HA15-0.9-AG B
12 1.7 HB12-1.7-AG B C
12 3.4 HC12-3.4-AG C C
12 5.1 HN12-5.1-AG N C
12 6.8 HD12-6.8-AG D C
12 10.2 HE12-10.2-AG E C
12 16 F15-15-AG F C, D, H
15* 0.9 HA15-0.9-AG B
15 1.5 HB15-1.5-AG B C
15 3 HC15-3-AG C C
15 4.5 HN15-4.5-AG N C
15 6 HD15-6-AG D C
15 9 HE15-9-AG E C
15* 15 F15-15-AG F C, D, H
Models with 24 to 28Vout, Sorted by Vout then Max Amps
24 0.5 HA24-0.5-AG B
24 1.2 HB24-1.2-AG B C
24 2.4 HC24-2.4-AG C C
24 3.6 HN24-3.6-AG N C
24 4.8 HD24-4.8-AG D C
24 7.2 HE24-7.2-AG E C
24 12 F24-12-AG F C, D, H
28* 0.5 HA24-0.5-AG B
28 1 HB28-1-AG B C
28 2 HC28-2-AG C C
28 3 HN28-3-AG N C
28 4 HD28-4-AG D C
28 6 HE28-6-AG E C
28* 10 F24-12-AG F C, D, H
Models with 48Vout, Sorted by Max Amps
48 0.5 HB48-0.5-AG B
48 1 HC48-1-AG C
48 3 HD48-3-AG D C
48 4 HE48-4-AG E C
* May require jumpering or potentiometer adjustment.
35
Unsigned output voltages are isolated and can be used as either + or - polarities.
Linear Power Supplies > Dual Output
Case Dimensions
Type (Inches)
AA 6.50 x 4.00 x 2.10
B 4.87 x 4.00 x 2.10
BAA 10.25 x 4.00 x 2.95
BB 7.00 x 4.87 x 2.95
C 5.62 x 4.87 x 2.95
CBB 11.00 x 4.87 x 3.28
CC 9.38 x 4.87 x 3.28
CP131 11.00 x 4.87 x 3.28
D 9.00 x 4.87 x 3.28
DBB 14.25 x 4.87 x 3.38
DCC 15.00 x 4.88 x 4.55
E 14.00 x 4.87 x 3.53
F 16.75 x 4.88 x 5.00
N 7.00 x 4.87 x 3.28
Case Dimensions
Type (Millimeters)
AA 165.10 x 101.60 x 53.34
B 123.70 x 101.60 x 53.34
BAA 260.35 x 101.60 x 74.93
BB 177.80 x 123.70 x 74.93
C 142.75 x 123.70 x 74.93
CBB 279.40 x 123.70 x 83.31
CC 238.25 x 123.70 x 83.31
CP131 279.40 x 123.70 x 83.31
D 228.60 x 123.70 x 83.31
DBB 361.95 x 123.70 x 85.85
DCC 381.00 x 123.95 x 115.57
E 355.60 x 123.70 x 89.66
F 425.50 x 123.95 x 127.00
N 177.80 x 123.70 x 83.31
A Overvoltage protection, set at 6.2 V ±0.4 V.
B Non-adjustable 3-terminal regulator.
C Remote sense provided.
D With output inhibit and parallel
operation master/slave capability.
E With output inhibit.
F Adjustable 3-terminal regulator.
G Can be made into an isolated output by
removing jumper W1.
H Model requires 100 LFM forced-air
cooling above 75% of rated output
power at 50 degrees C.
Nominal Max Model Input Case Additional
Vout* Amps 100 to 264 VAC Type Features & Notes
Models with 5V to 15Vout, Sorted by Nominal Vout then Max Amps
+5, –5 1.5, 1.5 HAA5-1.5/OVP-AG AA A
+5, –5 3, 3 HBB5-3/OVP-AG BB A
+5, –5 6, 6 HCC5-6/OVP-AG CC A, C
5, 12 to 15 2, 0.5 HAA512-AG AA A
5, 12 to 15 3, 1.25 HBB512-AG BB A, C
5, 12 to 15 6, 2.5 HCC512-AG CC A, C
+12, –5* 1, 0.4 HAA15-0.8-AG AA C
+12, –5* 1.7, 0.7 HBB15-1.5-AG BB C
+12, –12 0.4, 0.4 HAD12-0.4-AG B B
+12, –12 1, 1 HAA15-0.8-AG AA C
+12, –12 1.7, 1.7 HBB15-1.5-AG BB C
+12, –12 3.4, 3.4 HCC15-3-AG CC C
+12, –12* 5, 5 HDD15-5-AG E C
+12, –15* 1, 0.8 HAA15-0.8-AG AA C
+12, –15* 1.7, 1.5 HBB15-1.5-AG BB C
+12, –15* 3.4, 3 HCC15-3-AG CC C
+12, –15* 5, 5 HDD15-5-AG E C
+15, –5* 0.8, 0.4 HAA15-0.8-AG AA C
+15, –5* 1.5, 0.7 HBB15-1.5-AG BB C
+15, –12* 0.8, 1 HAA15-0.8-AG AA C
+15, –12* 1.5, 1.7 HBB15-1.5-AG BB C
+15, –12* 3, 3.4 HCC15-3-AG CC C
15, –12* 5, 5 HDD15-5-AG E C
Models with 15V to 24Vout, Sorted by Nominal Vout then Max Amps
+15, –15 0.4, 0.4 HAD15-0.4-AG B B
+15, –15 0.8, 0.8 HAA15-0.8-AG AA C
+15, –15* 1.5, 1.5 HBB15-1.5-AG BB C
+15, –15* 3, 3 HCC15-3-AG CC C
+15, –15 5, 5 HDD15-5-AG E C
+24, –24 0.6, 0.6 HAA24-0.6-AG AA
+24, –24 1.2, 1.2 HBB24-1.2-AG BB
+24, –24 2.4, 2.4 HCC24-2.4-AG CC C
* May require jumpering or potentiometer adjustment.
36
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Linear Power Supplies > Triple Output
Case Dimensions
Type (Inches)
AA 6.50 x 4.00 x 2.10
B 4.87 x 4.00 x 2.10
BAA 10.25 x 4.00 x 2.95
BB 7.00 x 4.87 x 2.95
C 5.62 x 4.87 x 2.95
CBB 11.00 x 4.87 x 3.28
CC 9.38 x 4.87 x 3.28
CP131 11.00 x 4.87 x 3.28
D 9.00 x 4.87 x 3.28
DBB 14.25 x 4.87 x 3.38
DCC 15.00 x 4.88 x 4.55
E 14.00 x 4.87 x 3.53
F 16.75 x 4.88 x 5.00
N 7.00 x 4.87 x 3.28
Case Dimensions
Type (Millimeters)
AA 165.10 x 101.60 x 53.34
B 123.70 x 101.60 x 53.34
BAA 260.35 x 101.60 x 74.93
BB 177.80 x 123.70 x 74.93
C 142.75 x 123.70 x 74.93
CBB 279.40 x 123.70 x 83.31
CC 238.25 x 123.70 x 83.31
CP131 279.40 x 123.70 x 83.31
D 228.60 x 123.70 x 83.31
DBB 361.95 x 123.70 x 85.85
DCC 381.00 x 123.95 x 115.57
E 355.60 x 123.70 x 89.66
F 425.50 x 123.95 x 127.00
N 177.80 x 123.70 x 83.31
A Overvoltage protection, set at
6.2 V ±0.4 V.
B Non-adjustable 3-terminal regulator.
C Remote sense provided.
D With output inhibit and parallel
operation master/slave capability.
E With output inhibit.
F Adjustable 3-terminal regulator.
G Can be made into an isolated output
by removing jumper W1.
H Model requires 100 LFM forced-air
cooling above 75% of rated output
power at 50 degrees C.
Nominal Max Model Input Case Additional
Vout* Amps 100 to 264 VAC Type Features & Notes
Models with 5V to 15Vout, Sorted by Nominal Vout then Max Amps
+5, +12, –5* 2, 0.4, 0.4 HTAA-16W-AG AA A
5, +12, –5* 3, 1, 0.4 HBAA-40W-AG BAA A, C
+5, +12, –5* 6, 1, 0.4 HCAA-60W-AG D A, C
5, +12, –5* 6, 1.7, 0.7 HCBB-75W-AG CBB C
5, +12, –5* 8, 1.7, 0.7 CP131-AG CP131 A, C
5, +12, –5* 12, 1.7, 0.7 HDBB-105W-AG DBB A, C
5, +12, –12 2, 0.4, 0.4 HTAA-16W-AG AA A
5, +12, –12 3, 1, 1 HBAA-40W-AG BAA A, C
+5, +12, –12 6, 1, 1 HCAA-60W-AG D A, C
5, +12, –12 6, 1.7, 1.7 HCBB-75W-AG CBB C
5, +12, –12 8, 1.7, 1.7 CP131-AG CP131 A, C
5, +12, –12 12, 1.7, 1.7 HDBB-105W-AG DBB C
5, +12, –12 12, 3.4, 3.4 HDCC-150W-AG DCC A, C
5, +12, –15* 2, 0.4, 0.4 HTAA-16W-AG AA A
5, +12, –15* 3, 1, 0.8 HBAA-40W-AG BAA A, C
+5, +12, –15* 6, 1, 1 HCAA-60W-AG D A, C
5, +12, –15 6, 1.7, 1.5 HCBB-75W-AG CBB C
5, +12, –15 8, 1.7, 1.5 CP131-AG CP131 A, C
5, +12, –15* 12, 1.7, 1.5 HDBB-105W-AG DBB C
5, +12, –15 12, 3.4, 3 HDCC-150W-AG DCC A, C
5, +15, –5* 2, 0.4, 0.4 HTAA-16W-AG AA A
5, +15, –5* 3, 0.8, 0.4 HBAA-40W-AG BAA A, C
+5, +15, –5* 6, 1, 0.4 HCAA-60W-AG D A, C
5, +15, –5* 6, 1.5, 0.7 HCBB-75W-AG CBB C
5, +15, –5* 8, 1.5, 0.7 CP131-AG CP131 A,
5, +15, –5* 12, 1.5, 0.7 HDBB-105W-AG DBB C
5, +15, –12* 2, 0.4, 0.4 HTAA-16W-AG AA A
5, +15, –12* 3, 0.8, 1 HBAA-40W-AG BAA A, C
+5, +15, –12* 6, 1, 1 HCAA-60W-AG D A, C
5, +15, –12 6, 1.5, 1.7 HCBB-75W-AG CBB C
5, +15, –12 8, 1.5, 1.7 CP131-AG CP131 A, C
5, +15, –12* 12, 1.5, 1.7 HDBB-105W-AG DBB C
5, +15, –12 12, 3, 3.4 HDCC-150W-AG DCC A, C
5, +15, –15* 2, 0.4, 0.4 HTAA-16W-AG AA A
5, +15, –15* 3, 0.8, 0.8 HBAA-40W-AG BAA A, C
+5, +15, –15* 6, 1, 1 HCAA-60W-AG D A, C
5, +15, –15 6, 1.5, 1.5 HCBB-75W-AG CBB C
5, +15, –15 8, 1.5, 1.5 CP131-AG CP131 A, C
5, +15, –15* 12, 1.5, 1.5 HDBB-105W-AG DBB C
5, +15, –15 12, 3, 3 HDCC-150W-AG DCC A, C
* May require jumpering or potentiometer adjustment.
37
Unsigned output voltages are isolated and can be used as either + or - polarities.
CompactPCI > AC-DC & DC Input
CPD250
3U x 8HP (8TE) x 6.3" (160mm)
6U x 8HP (8TE) x 6.3" (160mm)
CPA250
CPA500/CPA550
6U x 8HP (8TE) x 6.4" (163mm)
CPD500
3U x 8HP (8TE) x 6.3" (160mm)
Height Input +5V +3.3V +12V -12V
Model Watts Profile Voltage Current Current Current Current
DC Input Models
CPD250-4530 250 3U 36-75 VDC 40 A 40 A 5.5 A 2 A
CPD500-4530G 500 6U 36-75 VDC 50 A 60 A 12 A 4 A
AC Input Models
CPA250-4530 250 3U 90-264 VAC 40 A 40 A 5.5 A 2 A
CPA500-4530 500 6U 90-264 VAC 50 A 60 A 12 A 4 A
CPA550-4530 550 6U 90-264 VAC 50 A 60 A 12 A 4 A
Fully Compliant to CompactPCI Per PICMG
Specifications
High Density Design in an Industry-Standard
Package
High Efficiency Topology (>80%)
Remote Sense and Active Current Share for
3 Outputs
Built-In ORing FETs for Redundant
Applications
AC-DC Models Have Active Power Factor
Correction
Conformal Coating Option
Power-One’s hot-swap CompactPCI power supplies are fully compliant to the PICMG 2.11 Power Interface
Specification, and use a standard Positronic 47-pin connector. EDGE technology delivers up to 40 amperes
on both the +5 and +3.3 volt outputs at 50 ºC on the 3U models, and 50 and 60 amperes respectively, on
the 6U model’s +5 and +3.3 volt outputs.
Remote sense and active current share on the +5, +3.3, and +12 volt outputs, along with ORing FETs
facilitate use in redundant, hot-swap applications. These feature-rich products meet international safety
standards, and display the CE Mark for the Low Voltage Directive (LVD).
38
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Power Over Ethernet
10.40 x 4.00 x 1.59 inch
264.2 x 101.6 x 40.4 mm
PALS400/PALS600
HHS04 & HHS05
2.40 x 2.28 x 0.42 inch
61.0 x 57.9 x 10.7 mm
Provides full compliance to IEEE 802.3AF
Extremely low noise and ripple
48 VDC output has 2250 VDC isolation from the 12 VDC outputs and
I2C interface
85 to 264 VAC input range with IEC61000-3-2 compliant
98% efficient PFC
Full power operation to 50 °C with power-derated operation to 70 °C
Internal diode isolation for redundant operation of up to 30 PAL’s
Standard half-brick footprint and pinout
Fully regulated output
High efficiency
Input-to-output isolation: 2,250 VDC
The 10.4" x 4" x 1.6" package is designed for 1U high applications and features a front panel that includes
alarm and monitor LED's, AC input connector, on/off switch, integral handle, and a fan inlet. The hot-swap
SSI type rear connector provides output power and access to I2C, power fail, active current share, remote
sense, output good, power-supply present, and remote enable interface signals.
Protection features include overload and short circuit, brownout, overtemperature/fan fail warning and
shutdown, output overvoltage, and MOV input-transient. Agency approvals include UL1950, CSA 950, and
EN60950 (TUV).
Factory Output Max VAC Max
Set Vout Trim Range Amps Input Watts Model
48 N/A 8 85 to 264 400 PALS400-2482
12 N/A 16
48 N/A 9 85 to 264 600 PALS600-2482
12 N/A 16
Input Factory Output Max
Voltage Set Vout Trim Range Amps Model
36 to 75 52.5 50 to 53 3.8 HHS04Z52
36 to 75 53.7 51.2 to 54.2 4.8 HHS05Z55
Power Over Ethernet > DC-DC
Power Over Ethernet > AC-DC
39
Railway & Rugged Solutions Overview
A Proven Track Record
Isolated Cassette Style AC-DC and DC-DC
A broad range of extremely flexible cassettes are available,
providing from one to four outputs.
Features include high efficiencies, low noise outputs,
power factor correction, excellent line/load response,
wide-range inputs, and extensive interface capabilities.
Chassis, rack, and DIN-Rail mounting.
Rack power solutions can be configured from readily
available front panels and rack frames.
These non-isolated buck-converter topology converters
feature no power derating over the entire operating
temperature range, no minimum load operation, wide
output adjustment ranges, and -40 to 71 °C extended-
temperature-range options.
DC-DC Positive Switching Regulators
DIN-Rail Mount, Including EN 50155 Compliant Models
Single and dual output converters and battery chargers are
ideal power sources for demanding applications such as
building control systems, factory automation, industrial
controls, instrumentation, electromagnetic drives, fans,
and other DC loads.
Extremely robust electrical and mechanical designs have enabled Power-One’s broad range
of railway and rugged products to establish a proven track record of industry-leading
reliability, in a diverse array of transportation, communications, and industrial infrastructure
applications.
Rolling Stock Custom Power Capabilities
Power-One has field-proven design and
manufacturing capabilities for a wide
range of rolling-stock power applications.
Custom-product capabilities range from
low-wattage solutions, such as power
systems for onboard lighting and water
circulation, to train-wide 55 kW auxiliary
power converters.
Please contact your local Power-One
representative to discuss your railway
power-conversion requirements.
40
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
DIN-Rail Mount
W Series with PFC
5.43 x 4.49 x 4.05 inch
138 x 114 x 103 mm
Class I equipment
DC input 90 to 350 VDC
Compact 35 mm DIN-rail snap-
fit design or wall mounting
Ambient temperature range
-6: –40 to +60 °C
UL 508 listed
Battery charger models with
temperature sensor available
Vout Amps VAC Max
1, 2 1,2 Input Watts Model
Output Voltage Adjusts 50-110% By Specifying “R” Option
12.35 7.5 85 to 264 93 LWR1301-6E
12.35 14 85 to 264 173 LWN1301-6E
24.7 5 85 to 264 125 LWR1601-6E
24.7 10 85 to 264 250 LWN1601-6E
37 3.3 85 to 264 125 LWR1701-6E
37 6.6 85 to 264 250 LWN1701-6E
49.4 2.5 85 to 264 125 LWR1801-6E
49.4 5 85 to 264 250 LWN1801-6E
12.35, 12.35 7, 7 85 to 264 173 LWN2320-6E
24.7, 24.7 5, 5 85 to 264 250 LWN2660-6E
37, 37 3.3, 3.3 85 to 264 250 LWN2770-6E
49.4, 49.4 2.5, 2.5 85 to 264 250 LWN2880-6E
All ratings at 60 °C
W Series (125 to 250 Watts)
VAC Max
Vout Amps Input Watts Model
5.1 5.2 85 to 264 26 LOK4001-2RLD
12 4 85 to 264 48 LOK4301-2R
24 2 85 to 264 48 LOK4601-2R
48 1 85 to 264 48 LOK4801-2R
All ratings at 50 °C
LOK Series (26 to 48 Watts)
LOK Series
4.49 x 3.54 x 1.5 inch
114 x 90 x 38 mm
Class I equipment
DC input 90 to 250 VDC
Short circuit protection
Adjustable output for models
with R suffix
Battery charger models with
temperature sensor available
41
Unsigned output voltages are isolated and can be used as either + or - polarities.
Alpha-sorted graphics and
dimensions augment model
listings from both pages.
DIN-Rail Mount
X Series with PFC
5.43 x 4.47 x 7.64 inch
138 x 114 x 194 mm
W Series for Railway
Applications
Class I equipment
DC input 66 to 150 VDC
Safety according to IEC/EN
60950, EN 50155 compliant
Ambient temp. range
–40 to +71 °C
Vout Amps
1, 2 1, 2 VAC Input Watts Model
Output Voltage Adjusts 60-110% By Specifying “R” Option
24.7 15 85 to 264 371 LXR1601-6
24.7 20 85 to 264 494 LXN1601-6
37 10 85 to 264 370 LXR1701-6
37 13.4 85 to 264 496 LXN1701-6
49.4 7.5 85 to 264 371 LXR1801-6
49.4 10 85 to 264 494 LXN1801-6
24.7, 24.7 10, 10 85 to 264 494 LXN2660-6
37, 37 6.7, 6.7 85 to 264 496 LXN2770-6
49.4, 49.4 5, 5 85 to 264 494 LXN2880-6
Class I equipment
DC input 90 to 350 VDC
Safety: Class I equipment according
to IEC/EN60950, UL 60950,
EN 61010-1
Compact 35 mm DIN-rail snap-fit
design or wall mounting
Ambient temperature range
-6: –40 to 60 °C
Battery charger models with
temperature sensor available
DIN-Rail Mount
> Battery Chargers
Battery Nominal Nominal
Model Voltage Watts Output Voltage Output Amps
LOK4140-2RLD 12 49 12.8 3.6
LWN1140-6EM1 12 140 13.8 10
LOK4240-2RLD 24 49 25.7 1.8
LWR1240-6EM1 24 115 27.3 4.2
LWN1240-6EM1 24 230 27.3 8.45
LXR1240-6M1 24 344 27.3 12.6
LXN1240-6M1 24 458 27.3 16.8
LXR1840-6M1 36 343 40.9 8.4
LXN1840-6M1 36 458 40.9 11.2
LOK4740-2RLD 48 49 51.4 0.9
LWR1740-6EM1 48 115 54.5 2.1
LWN1740-6EM1 48 230 54.5 4.2
LXR1740-6M1 48 343 54.5 6.3
LXN1740-6M1 48 458 54.5 8.4
Please refer to data sheets for availability of EMI options, temperature sensor
options, and safety agency certifications.
Other battery chargers are available in Cassette packages; refer to the AC-DC
Cassette Section. Contact factory for availability.
Vout Amps VDC Max
1, 2 1,2 Input Watts Model
24.7 5 66 to 150 120 EWR1601-0
24.7, 24.7 5, 5 66 to 150 240 EWN2660-0
W Series > EN 50155 Compliant
X Series (375 to 496 Watts)
All ratings at 70 °C
42
www.power-one.com
Non-Isolated Positive Switching Regulators
PSA, PSR
2.76 x 2.00 x 1.00 inch
70.1 x 50.8 x 25.4 mm
PSB
4.17 x 2.72 x 1.27 inch
106 x 69 x 32.2 mm
PSC
5.94 x 3.46 x 1.27 inch
151 x 88 x 32.2 mm
Factory
Set Vout Amps VDC Input Watts Efficiency Model
+3.3 12 6 to 40 39.6 77 PSC3E12-2
+5 2 8 to 80 10 74 PSR52-7
+5 3 8 to 80 15 79 PSR53-7
+5 4 7 to 40 20 83 PSR54-7
+5 5 7 to 35 25 83 PSA55-7
+5.1 2 8 to 40 10.2 75 PSA5A2-2
+5.1 5 15 to 144 25.5 80 PSB5A4-7iR
+5.1 5 7 to 35 25.5 83 PSA5A5-2
+5.1 6 8 to 80 30.6 81 PSB5A6-7iR
+5.1 7 7 to 40 35.7 84 PSB5A7-7iR
+5.1 8 7 to 40 40.8 81 PSB5A8-2
+5.1 10 8 to 80 51 79 PSC5A10-7iR
+5.1 11 8 to 40 56.1 79 PSC5A11-2
+5.1 12 7 to 40 61.2 83 PSC5A12-7iR
+12 1.5 18 to 144 18 87 PSA121.5-7iR
+12 2.5 15 to 80 30 87 PSR122.5-7
+12 3 15 to 40 36 89 PSA123-2
+12 4 18 to 144 48 89 PSB123-7iR
+12 5 15 to 80 60 90 PSB125-7iR
+12 6 15 to 40 72 90 PSB126-2
+12 6 18 to 144 72 89 PSC126-7iR
+12 8 15 to 80 96 90 PSC128-7iR
+12 9 15 to 40 108 90 PSC129-2
+15 1.5 22 to 144 22.5 89 PSA151.5-7iR
+15 2.5 19 to 80 37.5 89 PSR152.5-7
+15 3 19 to 40 45 90 PSA153-2
+15 4 22 to 144 60 90 PSB153-7iR
+15 5 19 to 80 75 92 PSB155-7iR
+15 6 19 to 40 90 92 PSB156-2
+15 6 22 to 144 90 90 PSC156-7iR
+15 8 19 to 80 120 91 PSC158-7iR
+15 9 19 to 40 135 91 PSC159-2
+24 1.5 31 to 144 36 93 PSA241.5-7iR
+24 2 29 to 80 48 92 PSR242-7
+24 2.5 29 to 60 60 93 PSA242.5-2
+24 4 31 to 144 96 94 PSB243-7iR
+24 5 29 to 80 120 95 PSB245-7iR
+24 6 29 to 60 144 95 PSB246-2
+24 6 31 to 144 144 94 PSC246-7iR
+24 8 29 to 80 192 94 PSC248-7iR
+24 9 29 to 60 216 94 PSC249-2
+36 1.2 44 to 144 43.2 95 PSA361-7iR
+36 2 42 to 80 72 94 PSR362-7
+36 4 44 to 144 144 95 PSB363-7iR
+36 5 42 to 80 180 96 PSB365-7iR
+36 6 44 to 144 216 95 PSC366-7iR
+36 8 42 to 80 288 96 PSC368-7iR
+48 1 58 to 144 48 95 PSA481-7iR
+48 4 58 to 144 192 96 PSB483-7iR
+48 6 58 to 144 288 97 PSC486-7iR
PSR > Chassis Mount
Output Voltage Adjusts 0-110% in PSS Models with “R” Suffix;
Output Voltage Adjusts 0-108% in All Other Models with “R” Suffix.
43
Alpha-sorted graphics and
dimensions augment model
listings from both pages.
Non-Isolated Positive Switching Regulators
PSK
6.77 x 4.37 x 3.15 inch
171.9 x 111 (3U) x 80 (16TE) mm
PSL
6.83 x 4.21 x 1.44 inch
173.7 x 107 x 36.5 mm
PSS
6.77 x 4.37 x 2.36 inch
171.9 x 111 (3U) x 60 (12TE) mm
Factory
Set Vout Amps VDC Input Watts Efficiency Model
+5.1 10 8 to 80 51 79 PSL5A10-7R
+5.1 11 8 to 40 56.1 79 PSL5A11-2R
+5.1 12 7 to 40 61.2 83 PSL5A12-7R
+5.1 12 8 to 80 61.2 79 PSS5A12-7
+5.1 14 8 to 40 71.4 83 PSS5A14-2
+5.1 16 8 to 80 81.6 79 PSK5A16-7
+5.1 18 8 to 40 91.8 82 PSK5A18-2
+5.1 20 8 to 80 102 79 PSK5A20-7
+5.1 25 8 to 40 127.5 82 PSK5A25-7
+12 6 18 to 144 72 89 PSL126-7R
+12 8 15 to 80 96 90 PSL128-7R
+12 9 15 to 40 108 90 PSL129-2R
+12 9 18 to 144 108 91 PSS129-7
+12 12 15 to 80 144 91 PSS1212-7
+12 12 18 to 144 144 91 PSK1212-7
+12 14 16 to 40 168 90 PSS1214-2
+12 16 15 to 80 192 90 PSK1216-7
+12 18 16 to 40 216 90 PSK1218-2
+12 20 15 to 80 240 90 PSK1220-7
+15 6 22 to 144 90 90 PSL156-7R
+15 8 19 to 80 120 91 PSL158-7R
+15 9 19 to 40 135 91 PSL159-2R
+24 6 31 to 144 144 94 PSL246-7R
+24 8 29 to 80 192 94 PSL248-7R
+24 9 29 to 60 216 94 PSL249-2R
+24 9 31 to 144 216 94 PSS249-7
+24 12 29 to 80 288 94 PSS2412-7
+24 12 31 to 144 288 94 PSK2412-7
+24 14 29 to 60 336 94 PSS2414-2
+24 16 29 to 80 384 94 PSK2416-7
+24 18 29 to 60 432 94 PSK2418-2
+24 20 29 to 80 480 94 PSK2420-7
+36 6 44 to 144 216 96 PSL366-7R
+36 8 42 to 80 288 96 PSL368-7R
+36 9 44 to 144 324 96 PSS369-7
+36 12 42 to 80 432 96 PSS3612-7
+36 12 44 to 144 432 96 PSK3612-7
+36 16 42 to 80 576 95 PSK3616-7
+36 20 42 to 80 720 95 PSK3620-7
+48 6 58 to 144 288 97 PSL486-7R
+48 9 58 to 144 432 97 PSS489-7
+48 12 58 to 144 576 97 PSK4812-7
PSR > Cassette Style
Output Voltage Adjusts 0-110% in PSS Models with “R” Suffix;
Output Voltage Adjusts 0-108% in All Other Models with “R” Suffix.
44
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > DC-DC
M Series
6.6 x 4.4(3U) x 1.54(8 TE) inch
168 x 111 x 39 mm
Output Adjustment Ranges
The following adjustment ranges
apply to all single-output models.
Vout Low High
5.1 0 5.6
12 0 13.2
15 0 16.5
24 0 26.4
48 0 52.8
Vout Amps Model Input Model Input Model Input
1, 2, 3 1, 2, 3 8 to 35 VDC 14 to 70 VDC 20 to 100 VDC
5.1 8 AM1001-7R BM1001-7R FM1001-7R
12 4 AM1301-7R BM1301-7R FM1301-7R
15 3.4 AM1501-7R BM1501-7R FM1501-7R
24 2 AM1601-7R BM1601-7R FM1601-7R
48 1 AM1901-7R BM1901-7R FM1901-7R
12, 12 2, 2 AM2320-7 BM2320-7 FM2320-7
15, 15 1.7, 1.7 AM2540-7 BM2540-7 FM2540-7
5.1, 12, 12 5, 0.7, 0.7 AM3020-7 BM3020-7 FM3020-7
5.1, 15, 15 5, 0.6, 0.6 AM3040-7 BM3040-7 FM3040-7
Vout Amps Model Input Model Input Model Input
1, 2, 3 1, 2, 3 28 to 140 VDC 44 to 220 VDC 88 to 372 VDC
5.1 8 CM1001-7R DM1001-7R LM1001-7R
12 4 CM1301-7R DM1301-7R LM1301-7R
15 3.4 CM1501-7R DM1501-7R LM1501-7R
24 2 CM1601-7R DM1601-7R LM1601-7R
48 1 CM1901-7R DM1901-7R LM1901-7R
12, 12 2, 2 CM2320-7 DM2320-7 LM2320-7
15, 15 1.7, 1.7 CM2540-7 DM2540-7 LM2540-7
5.1, 12, 12 5, 0.7, 0.7 CM3020-7 DM3020-7 LM3020-7
5.1, 15, 15 5, 0.6, 0.6 CM3040-7 DM3040-7 LM3040-7
M Series (40 to 50 Watts)
Safety: Class I equipment according to
IEC/EN 60950, UL 60950.
Extremely wide input voltage range
Input over- and undervoltage lockout
Output voltage control (R) and inhibit
Surge and transient suppression circuitry
Fully isolated outputs
Outputs open- and short-circuit proof
Ambient temperature range
-7: –25 to 71 °C
No derating over temperature
45
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > DC-DC
S Series
6.7 x 4.4(3U) x 2.4(12 TE) inch
168 x 111 x 60 mm
Please see the AC-DC
S-Series data sheets for AC input
LS models.
Output Adjustment Ranges
The following adjustment ranges
apply to all models.
Vout Low High
5.1 0 5.6
12 0 13.2
15 0 16.5
24 0 26.4
48 0 52.8
Vout Amps Model Input Model Input Model Input
1, 2 1, 2 8 to 35 VDC 14 to 70 VDC 20 to 100 VDC
5.1 16 AS1001-7R BS1001-7R FS1001-7R
12 8 AS1301-7R BS1301-7R FS1301-7R
15 6.5 AS1501-7R BS1501-7R FS1501-7R
24 4.2 AS1601-7R BS1601-7R FS1601-7R
12, 12 4, 4 AS2320-7R BS2320-7R FS2320-7R
15, 15 3.2, 3.2 AS2540-7R BS2540-7R FS2540-7R
24, 24 2, 2 AS2660-7R BS2660-7R FS2660-7R
Vout Amps Model Input Model Input Model Input
1, 2 1, 2 28 to 140 VDC 44 to 220 VDC 67 to 385 VDC
5.1 16 CS1001-7R DS1001-7R ES1001-7R
12 8 CS1301-7R DS1301-7R ES1301-7R
15 6.5 CS1501-7R DS1501-7R ES1501-7R
24 4.2 CS1601-7R DS1601-7R ES1601-7R
12, 12 4, 4 CS2320-7R DS2320-7R ES2320-7R
15, 15 3.2, 3.2 CS2540-7R DS2540-7R ES2540-7R
24, 24 2, 2 CS2660-7R DS2660-7R ES2660-7R
S Series (80 to 96 Watts)
Safety: Class I equipment according to
IEC/EN 60950, UL 60950; BS, CS, DS, ES, FS
comply with EN 50155
Extremely wide input voltage range
Input over- and undervoltage lockout
Output voltage control (R) and inhibit
Surge and transient suppression circuitry
Fully isolated outputs
Outputs open- and short-circuit proof
Ambient temperature range
-7: –25 to 71 °C
No derating over temperature
46
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > DC-DC
Q Series
6.5 x 4.4(3U) x 0.8(4 TE) inch
164 x 111 x 20 mm
Output Adjustment Ranges
The following adjustment ranges
apply to V1 and V2 outputs.
Vout Low High
3.3 3.3 3.3
5.1 4.1 5.6
12 7.2 13.2
15 9.0 16.5
24 14.4 26.4
48 28.8 52.8
Safety: Class I equipment according to
IEC/EN 60950, UL 60950, compliant to EN 50155;
48Q Series compliant to ETS 300 132-2
Extremely slim case (4TE wide), fully enclosed
Outputs, units parallel or series configurable
Flexible load distribution
Very high efficiency up to 90%
Ambient temperature ranges:
-9: –40 to 71 °C
-2: –10 to 50 °C
Output voltage control (R) and inhibit
Output OK monitor
Redundant operation and current sharing
Extremely low inrush current, hot plug-in
Extremely slim case (4 TE) fully enclosed
Vout Amps Amps Model Input Model Input Model Input
1, 2 1, 2 TA= 50°C 14.4 to 36 VDC 21.6 to 54 VDC 33.6 to 75 VDC
3.3 20 25 BQ1101-9 GQ1101-9 CQ1101-9
5.1 16 20 BQ1001-9R GQ1001-9R CQ1001-9R
5.1, 5.1 7.5, 7.5 9.5, 9.5 BQ2001-9R GQ2001-9R CQ2001-9R
12, 12 4, 4 5, 5 BQ2320-9R GQ2320-9R CQ2320-9R
15, 15 3.3, 3.3 4, 4 BQ2540-9R GQ2540-9R CQ2540-9R
24, 24 2.2, 2.2 2.75, 2.75 BQ2660-9R GQ2660-9R CQ2660-9R
Vout Amps Amps Model Input Model Input Model Input
1, 2 1, 2 TA= 50°C 43 to 108 VDC 65 to 150 VDC 38.4 to 75 VDC
3.3 20 25 DQ1101-9 EQ1101-9
5.1 16 20 DQ1001-9R EQ1001-9R 48Q1001-2R
5.1, 5.1 7.5, 7.5 9.5, 9.5 DQ2001-9R EQ2001-9R
12, 12 4, 4 5, 5 DQ2320-9R EQ2320-9R 48Q2320-2R
15, 15 3.3, 3.3 4, 4 DQ2540-9R EQ2540-9R 48Q2540-2R
24, 24 2.2, 2.2 2.75, 2.75 DQ2660-9R EQ2660-9R 48Q2660-2R
Q Series (66 to 132 Watts)
47
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > DC-DC
K Series
6.6 x 4.4(3U) x 3.2(16 TE) inch
168 x 111 x 80 mm
Please see the AC-DC
K-Series data sheets for AC input
LK models.
Output Adjustment Ranges
The following adjustment ranges
apply to all models.
Vout Low High
5.1 0 5.6
12 0 13.2
15 0 16.5
24 0 26.4
Vout Amps VDC
1, 2 1, 2 Model Input
5.1 20 AK1001-7R 8 to 35
12 10 AK1301-7R 8 to 35
15 8 AK1501-7R 8 to 35
24 5 AK1601-7R 8 to 35
12, 12 5, 5 AK2320-7R 8 to 35
15, 15 4, 4 AK2540-7R 8 to 35
24, 24 2.5, 2.5 AK2660-7R 8 to 35
Vout Amps Model Input Model Input
1, 2 1, 2 14 to 70 VDC 20 to 100 VDC
5.1 25 BK1001-7R FK1001-7R
12 12 BK1301-7R FK1301-7R
15 10 BK1501-7R FK1501-7R
24 6 BK1601-7R FK1601-7R
12, 12 6, 6 BK2320-7R FK2320-7R
15, 15 5, 5 BK2540-7R FK2540-7R
24, 24 3, 3 BK2660-7R FK2660-7R
Vout Amps Model Input Model Input Model Input Model Input
1, 2 1, 2 28 to 140 VDC 44 to 220 VDC 67 to 385 VDC 88 to 372 VDC
5.1 25 CK1001-7R DK1001-7R LK1001-7R
12 12 CK1301-7R DK1301-7R EK1301-7R LK1301-7R
15 10 CK1501-7R DK1501-7R EK1501-7R LK1501-7R
24 6 CK1601-7R DK1601-7R EK1601-7R LK1601-7R
12, 12 6, 6 CK2320-7R DK2320-7R EK2320-7R LK2320-7R
15, 15 5, 5 CK2540-7R DK2540-7R EK2540-7R LK2540-7R
24, 24 3, 3 CK2660-7R DK2660-7R EK2660-7R LK2660-7R
Safety: Class I equipment according to
IEC/EN 60950, UL 60950; BK, CK, DK, EK, FK
comply with EN 50155.
Extremely wide input voltage range
Input over- and undervoltage lockout
Output voltage control (R) and inhibit
Surge and transient suppression circuitry
Fully isolated outputs
Outputs open- and short-circuit proof
Ambient temperature range
-7: –25 to 71 °C
No derating over temperature
K Series (102 to 150 Watts)
48
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > DC-DC
P Series
6.5 x 4.4(3U) x 0.8(4 TE) inch
164 x 111 x 20 mm
Output Adjustment Ranges
The following adjustment ranges
apply to single-output models
and V1 of multi-output models.
Vout Low High
3.3 1.8 3.6
5.1 2.75 5.6
12 6.5 13.2
15 8.1 16.5
24 13.0 26.4
Vout Vout Max. Nom. Model Input Model Input
1, 4 2, 3 Watts Watts 16 to 36 VDC 33.6 to 75 VDC
12 192 120 BP1301-9R CP1301-9R
15 194 120 BP1501-9R CP1501-9R
24 192 120 BP1601-9R CP1601-9R
3.3 5.1 157 111 BP2101-9R CP2101-9R
5.1 5.1 182 122 BP2001-9R CP2001-9R
5.1 12 187 121 BP2020-9R CP2020-9R
12 12 192 120 BP2320-9R CP2320-9R
15 15 194 120 BP2540-9R CP2540-9R
24 24 192 120 BP2660-9R CP2660-9R
5.1 12, 12 187 121 BP3020-9R CP3020-9R
5.1 15, 15 187 121 BP3040-9R CP3040-9R
5.1 24, 24 187 121 BP3060-9R CP3060-9R
5.1, 3.3 12, 12 146 90 BP4720-9R CP4720-9R
12, 12 12, 12 192 120 BP4320-9R CP4320-9R
15, 15 15, 15 192 120 BP4540-9R CP4540-9R
24, 24 24, 24 192 120 BP4660-9R CP4660-9R
Vout Vout Max. Nom. Model Input Model Input
1, 4 2, 3 Watts Watts 40 to 101 VDC 66 to 150 VDC
12 192 120 DP1301-9R EP1301-9R
15 194 120 DP1501-9R EP1501-9R
24 192 120 DP1601-9R EP1601-9R
3.3 5.1 157 111 DP2101-9R EP2101-9R
5.1 5.1 182 122 DP2001-9R EP2001-9R
5.1 12 187 121 DP2020-9R EP2020-9R
12 12 192 120 DP2320-9R EP2320-9R
15 15 194 120 DP2540-9R EP2540-9R
24 24 192 120 DP2660-9R EP2660-9R
5.1 12, 12 187 121 DP3020-9R EP3020-9R
5.1 15, 15 187 121 DP3040-9R EP3040-9R
5.1 24, 24 187 121 DP3060-9R EP3060-9R
5.1, 3.3 12, 12 146 90 DP4720-9R EP4720-9R
12, 12 12, 12 192 120 DP4320-9R EP4320-9R
15, 15 15, 15 192 120 DP4540-9R EP4540-9R
24, 24 24, 24 192 120 DP4660-9R EP4660-9R
P Series (90 to 194 Watts)
49
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > DC-DC
P Series
6.5 x 4.4(3U) x 0.8(4 TE) inch
164 x 111 x 20 mm
Output Adjustment Ranges
The following adjustment ranges
apply to single-output models
and V1 of multi-output models.
Vout Low High
3.3 1.8 3.6
5.1 2.75 5.6
12 6.5 13.2
15 8.1 16.5
24 13.0 26.4
Vout Vout Max. Nom. Model Input
1, 4 2, 3 Watts Watts 21.6 to 50.4 VDC
12 192 120 GP1301-9R
15 194 120 GP1501-9R
24 192 120 GP1601-9R
3.3 5.1 157 111 GP2101-9R
5.1 5.1 182 122 GP2001-9R
5.1 12 187 121 GP2020-9R
12 12 192 120 GP2320-9R
15 15 194 120 GP2540-9R
24 24 192 120 GP2660-9R
5.1 12, 12 187 121 GP3020-9R
5.1 15, 15 187 121 GP3040-9R
5.1 24, 24 187 121 GP3060-9R
5.1, 3.3 12, 12 146 90 GP4720-9R
12, 12 12, 12 192 120 GP4320-9R
15, 15 15, 15 192 120 GP4540-9R
24, 24 24, 24 192 120 GP4660-9R
P Series (90 to 194 Watts) [Continued]
Safety: Class I equipment according to IEC/EN 60950,
UL 60950, EN 50155 compliant
Flexible load distribution
Excellent surge and transient protection
Very high efficiency up to 92%
Ambient temperature range -9: –40 to 71 °C
Parallelability
Extremely low inrush current, hot plug-in
Inhibit on primary side
Extremely slim case (4TE wide) fully enclosed
50
www.power-one.com
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > AC-DC
M Series
6.6 x 4.4(3U) x 1.54(8 TE) inch
168 x 111 x 39 mm
Output Adjustment Ranges
The following adjustment ranges
apply to all single-output models.
Vout Low High
5.1 0 5.5
12 0 13.2
15 0 16.5
24 0 26.4
48 0 52.8
6.6 x 4.4(3U) x 1.54(8 TE) inch
168 x 111 x 39 mm
H Series
Output Adjustment Ranges
The following adjustment ranges
apply to single-output models.
Vout Low High
5.1 0 5.6
12 0 13.2
15 0 16.5
24 0 26.4
48 0 52.8
M and H Series Features
Safety: Class I equipment according to
IEC/EN60950, UL1950
Universal input voltage range
Output voltage control (R)
Surge and transient suppression circuitry
Outputs individually isolated and fully protected
against overload.
Vout Amps VAC
1, 2, 3 1, 2, 3 Input Model
5.1 8 85 to 264 LM1001-7R
12 4 85 to 264 LM1301-7R
15 3.4 85 to 264 LM1501-7R
24 2 85 to 264 LM1601-7R
48 1 85 to 264 LM1901-7R
12, 12 2, 2 85 to 264 LM2320-7
15, 15 1.7, 1.7 85 to 264 LM2540-7
5.1, 12, 12 5, 0.7, 0.7 85 to 264 LM3020-7
5.1, 15, 15 5, 0.6, 0.6 85 to 264 LM3040-7
Output Amps Max Model Input
1, 2, 3 1, 2, 3 Watts 85 to 255 VAC
5.1 11 56 LH1001-2R
12 6 72 LH1301-2R
15 4.5 67 LH1501-2R
24 3 72 LH1601-2R
48 1.5 72 LH1901-2R
12, 12 2, 2 48 LH2320-2
15, 15 1.7, 1.7 51 LH2540-2
5.1, 12, 12 5, 0.7, 0.7 42 LH3020-2
5.1, 15, 15 5, 0.6, 0.6 43 LH3040-2
H Series (42 to 72 Watts)
M Series (40 to 50 Watts)
Cassette
> Battery Chargers
Battery Nominal Nominal Output
Model Voltage Watts Output Voltage Amps
LM1781-7RD5 12 50 12.84 3.6
LH1781-2R 12 70 12.84 5
LK4740-7R 12 150 12.84 10
LM1782-7R 24 50 25.68 1.8
LH1782-2R 24 70 25.68 2.5
LK5740-7R 24 150 25.68 2.7
LKP5740-6R 24 250 25.68 4.5
LM1783-7R 36 50 38.52 1.2
LH1783-2R 36 70 38.52 1.67
LM1784-7R 48 50 51.36 0.9
LH1784-2R 48 70 51.36 1.25
LK5740-7R 48 150 2 x 25.68 2 x 2.7
LKP5740-6R 48 250 2 x 25.68 2 x 4.5
LM1785-7R 60 50 64.2 60.72
LH1785-2R 60 70 64.2 1
51
Unsigned output voltages are isolated and can be used as either + or - polarities.
Cassette > AC-DC
S Series
6.6 x 4.4(3U) x 2.4(12 TE) inch
168 x 111 x 60 mm
Output Adjustment Ranges
The following adjustment ranges
apply to all models.
Vout Low High
5.1 0 5.6
12 0 13.2
15 0 16.5
24 0 26.4
48 0 52.8
6.6 x 4.4(3U) x 3.2(16 TE) inch
168 x 111 x 80 mm
K Series
Output Adjustment Ranges
The following adjustment ranges
apply to all models.
Vout Low High
5.1 0 5.6
12 0 13.2
15 0 16.5
24 0 26.4
Safety: Class I equipment according to
IEC/EN 60950, UL 60950
LS 1000/2000 no PFC,
fin
47 to 440 Hz
Output voltage control (R) and inhibit
Outputs open- and short-circuit proof
Ambient temperature range -7: –25 to 71 °C
No derating over temperature
Vout Amps VAC
1, 2 1, 2 Input Model PFC
5.1 16 85 to 264 LS1001-7R no
5.1 16 85 to 264 LS4001-7R yes
12 8 85 to 264 LS1301-7R no
12 8 85 to 264 LS4301-7R yes
15 6.5 85 to 264 LS1501-7R no
15 6.5 85 to 264 LS4501-7R yes
24 4.2 85 to 264 LS1601-7R no
24 4.2 85 to 264 LS4601-7R yes
12, 12 4, 4 85 to 264 LS2320-7R no
12, 12 4, 4 85 to 264 LS5320-7R yes
15, 15 3.2, 3.2 85 to 264 LS2540-7R no
15, 15 3.2, 3.2 85 to 264 LS5540-7R yes
24, 24 2, 2 85 to 264 LS2660-7R no
24, 24 2, 2 85 to 264 LS5660-7R yes
S Series (81 to 100 Watts)
Safety: Class I equipment according to LK 1000/2000 no PFC,
fin
47 to 440 Hz
IEC/EN 60950, UL 1950 Output voltage control (R) and inhibit
Universal wide input voltage range (LK models) Input over- and undervoltage lockout
Efficient input filter
Vout Amps VAC
1, 2 1, 2 Input Model PFC
5.1 25 85 to 264 LK1001-7R no
5.1 25 85 to 264 LK4003-6R yes
12 12 85 to 264 LK1301-7R no
12 12 85 to 264 LK4301-7R yes
15 10 85 to 264 LK1501-7R no
15 10 85 to 264 LK4501-7R yes
24 6 85 to 264 LK1601-7R no
24 6 85 to 264 LK4601-7R yes
12, 12 6, 6 85 to 264 LK2320-7R no
12, 12 6, 6 85 to 264 LK5320-7R yes
12, 12 10, 10 187 to 255 LKP5320-6R yes
15, 15 5, 5 85 to 264 LK2540-7R no
15, 15 5, 5 85 to 264 LK5540-7R yes
24, 24 3, 3 85 to 264 LK2660-7R no
24, 24 3, 3 85 to 264 LK5660-7R yes
24, 24 4.8, 4.8 187 to 255 LKP5662-7R yes
24, 24 5.2, 5.2 187 to 255 LKP5660-7R yes
24, 24 5.8, 5.8 187 to 255 LKP5661-5R yes
K & KP Series (127 to 278 Watts)
Visit our web site:
www.power-one.com
Includes Global Sales and
Distributor Listings
Power-One, Inc.
740 Calle Plano
Camarillo, CA 93012
(800) 678-9445
