STA2500DC - STMicroelectronics - Datasheet.Directory

September 2013 Doc ID 16067 Rev 3 1/58

STA2500D

Bluetooth™ V2.1 + EDR ("Lisbon") for automotive applications

Features

■Based on Ericsson technology licensing

baseband core (EBC)

■Bluetooth™ specification compliance:

V2.1 + EDR (“Lisbon”)

– Point-to-point, point-to-multipoint (up to 7

slaves) and scatternet capability

– Support ACL and SCO links

– Extended SCO (eSCO) links

– Faster connection

■HW support for packet types

– ACL: DM1, DM3, DM5, DH1, DH3, DH5, 2-

DH1, 2-DH3, 2-DH5, 3-DH1, 3-DH3, 3-DH5

– SCO: HV1, HV3 and DV

– eSCO: EV3, EV4, EV5, 2-EV3, 2-EV5, 3-

EV3, 3-EV5

■Adaptive frequency hopping (AFH)

■Channel quality driven data rate (CQDDR)

■“Lisbon” features

– Encryption pause/resume (EPR)

– Extended inquiry response (EIR)

– Link supervision time out (LSTO)

– Secure simple pairing

– Sniff subrating

– Quality of service (QoS)

Packet boundary flag

Erroneous data delivery

■Transmit power

– Power class 2 and power class 1.5 (above

4 dBm)

– Programmable output power

– Power class 1 compatible

■HCI

– HCI H4 and enhanced H4 transport layer

– HCI proprietary commands (e.g.

peripherals control)

– Single HCI command for patch/upgrade

download

– eSCO over HCI supported

■

Supports pitch-period error concealment (PPEC)

■Efficient and flexible support for WLAN

coexistence scenarios

■Low power consumption

– Ultra low power architecture with 3 different

low-power levels

– Deep sleep modes, including host-power

saving feature

– Dual wake-up mechanism: initiated by the

host or by the Bluetooth device

■Communication interfaces

– Fast UART up to 4 MHz

– Flexible SPI interface up to 13 MHz

– PCM interface

– Up to 10 additional flexibly programmable

GPIOs

– External interrupts possible through the

GPIOs

–Fast I

2C interface as master

■Clock support

– System clock input (digital or sine wave) at

9.6, 10, 13, 16, 16.8, 19.2, 26, 33.6 or 38.4 MHz

– Low power clock input at 3.2 kHz, 32 kHz

and 32.768 kHz

■ARM7TDMI CPU

■Memory organization

– On chip RAM, including provision for

patches

– On chip ROM, preloaded with SW up to

HCI

■Ciphering support up to 128-bit key

■Single power supply with internal regulators for

core voltage generation

■Supports 1.65 V to 2.85 V I/O systems

■Auto calibration (VCO, filters)

LFBGA48 (6x6x1.4mm; 0.8mm Pitch)

www.st.com

Contents STA2500D
2/58 Doc ID 16067 Rev 3
Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Quick reference data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
2 Operating ranges  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7
3 I/O specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
4 Clock specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8
5 Current consumption  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
Block diagram and electrical schematic  . . . . . . . . . . . . . . . . . . . . . . . . 12
Pinout  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1 Pin description and assignment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13
2 HW configuration of the STA2500D  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16
3 I/O Supply   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17
Functional description  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1 Transmitter  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18
2 Receiver  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18
3 PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18
4 Bluetooth controller V1.2 and V2.0 + EDR features . . . . . . . . . . . . . . . . .  19
5 Bluetooth controller V2.1 + EDR (“Lisbon”)  . . . . . . . . . . . . . . . . . . . . . . .  19
6 Processor and memory   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19
7 TX output power control  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20
General specification  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1 Receiver  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21
2 Transmitter  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24
3 Class 1 operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
4 Power-up   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26
5 System clock   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27
6 Low power clock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27
7 Clock detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27

STA2500D Contents
Doc ID 16067 Rev 3 3/58
8 Clock request signals  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27
9 Interrupts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29
10 Low power modes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29
10.1 Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10.2 Some examples for the usage of the low power modes   . . . . . . . . . . . . 30
10.3 Deep sleep mode entry and wake-up   . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11 Patch RAM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37
12 Download of SW parameter file  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37
13 Bluetooth - WLAN coexistence in collocated scenario  . . . . . . . . . . . . . . .  38
13.1 Algorithm 1: PTA (packet traffic arbitration)  . . . . . . . . . . . . . . . . . . . . . . 38
13.2 Algorithm 2: WLAN master   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.3 Algorithm 3: Bluetooth master  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.4 Algorithm 4: two-wire mechanism  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
13.5 Algorithm 5: Alternating wireless medium access (AWMA) . . . . . . . . . . 40
Digital interfaces  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
1 The UART interface  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41
2 The SPI interface  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41
3 The PCM interface  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43
4 The JTAG interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46
5 Alternate I/O functions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46
6 The I2C interface   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47
HCI transport layer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
1 H4 UART transport layer   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48
2 Enhanced H4 SPI transport layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
3 H4 SPI transport layer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
4 eSCO over HCI   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
Package information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Acronyms and abbreviations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Order codes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Revision history   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

List of tables STA2500D
4/58 Doc ID 16067 Rev 3
List of tables
Table 1. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 2. Operating ranges  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 3. DC input specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 4. DC output specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 5. System clock supported frequencies  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 6. System clock overall specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 7. System clock, sine wave specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 8. System clock, digital clock DC specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 9. System clock, digital clock AC specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 10. Low power clock specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 11. Current consumption  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 12. The STA2500D pin list (functional and supply). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 13. Configuration programming  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 14. I/O supply split diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 15. Mbps receiver parameters - GFSK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 16. Mbps receiver parameters - /4-DQPSK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 17. Mbps receiver parameters - 8-DPSK  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 18. Transmitter parameters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 19. Output power: class 1 control signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 20. Output power: class 1 device pin configuration (depending on SW parameter download). 26
Table 21. Output power: class 1 device pin configuration (depending on SW parameter download). 26
Table 22. Use of the BT_CLK_REQ_IN and BT_CLK_REQ_OUT signals in different modes. . . . . . 28
Table 23. Low power modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 24. WLAN HW signal assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 25. SPI timing parameters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 26. PCM interface parameters  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 27. PCM interface timing (at PCM_CLK = 2048 kHz). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 28. Examples of BT_GPIO pin programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 29. Package markings legend  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table 30. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 31. Acronyms and abbreviations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 32. Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 33. Document revision history  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

STA2500D List of figures
Doc ID 16067 Rev 3 5/58
List of figures
Figure 1. Block diagram and electrical schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 2. Pinout (bottom view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 3. Active high clock request input and output combined with UART or SPI . . . . . . . . . . . . . . 28
Figure 4. Active low clock request input and output combined with UART  . . . . . . . . . . . . . . . . . . . . 28
Figure 5. Active low clock request input and output combined with SPI  . . . . . . . . . . . . . . . . . . . . . . 28
Figure 6. Deep sleep mode entry and wake-up through H4 UART . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 7. Entering deep sleep mode through enhanced H4 SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 8. Wake-up by the host through enhanced H4 SPI  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 9. Wake-up by the Bluetooth controller with data transmission to the host, through enhanced H4 
SPI 34
Figure 10. Deep sleep mode entry and wake-up through H4 SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 11. Entering deep sleep mode, pending data on UART interface, through UART with handshake
36
Figure 12. Wakeup by host through UART with handshake  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 13. PTA diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 14. WLAN master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 15. Bluetooth master. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 16. SPI interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 17. SPI data transfer timing for data length of 8 bits and lsb first, full duplex . . . . . . . . . . . . . . 42
Figure 18. SPI setup and hold timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 19. PCM (A-law, µ-law) standard mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 20. Linear mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 21. Multislot operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 22. PCM interface timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 23. UART transport layer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Figure 24. LFBGA48 (6x6x1.4mm) mechanical data and package dimensions  . . . . . . . . . . . . . . . . . 50
Figure 25. Package markings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Description STA2500D

6/58 Doc ID 16067 Rev 3

1 Description

The STA2500D is a single chip Bluetooth solution that is fully optimized for automotive

applications such as telematics, navigation and portable navigation. Power consumption

levels are targeted at battery powered devices and single chip solution brings cost

advantages. Manufacturers can easily and quickly integrate the STA2500D on their product

to enable a rapid time to market.

STA2500D supports the Bluetooth specification V2.1 + EDR (“Lisbon“) and is optimized in

terms of RF performance and cost.

The STA2500D is a ROM-based solution targeted at applications requiring integration up to

HCI level. Patch RAM is available, enabling multiple patches/upgrades and fast time to

volume. The STA2500D’s main interfaces are UART or SPI for HCI transport, PCM for voice

and GPIOs for control purposes.

The radio has been designed specifically for single chip requirements, for low power

consumption and minimum BOM count.

STA2500D Quick reference data

Doc ID 16067 Rev 3 7/58

2 Quick reference data

BT_VIO_x means BT_VIO_A, BT_VIO_B.

BT_HVx means BT_HVA, BT_HVD.

(See also Ta b l e 1 2 .)

2.1 Absolute maximum ratings

The absolute maximum rating (AMR) corresponds to the maximum value that can be

applied without leading to instantaneous or very short-term unrecoverable hard failure

(destructive breakdown).

2.2 Operating ranges

Operating ranges define the limits for functional operation and parametric characteristics of

the device. Functionality outside these limits is not implied.

Table 1. Absolute maximum ratings

Symbol Parameter Min. Max. Unit

BT_HVx Core supply voltages -0.3 4.0 V

BT_VIO_A Supply voltage I/O -0.3 4.0 V

BT_VIO_B Supply voltage I/O (for the low power clock) -0.3 4.0 V

BT_V

Input voltage of any digital pin -0.3 4.0 V

ssdiff

Maximum voltage difference between different types of

Vss pins. -0.3 0.3 V

stg

Storage temperature - 65 + 150 °C

Table 2. Operating ranges

Symbol Parameter Min. Typ. Max. Unit

BT_T

amb

Operating ambient temperature -40 25 +85 °C

BT_HVx Core supply voltages 2.65 2.75 2.85 V

BT_VIO_A I/O supply voltage 1.65 - 2.85 V

BT_VIO_B I/O supply voltage (for the low power clock) 1.17 - 2.85 V

Quick reference data STA2500D

8/58 Doc ID 16067 Rev 3

2.3 I/O specifications

The I/Os comply with the EIA/JEDEC standard JESD8-B.

2.4 Clock specifications

The STA2500D supports, on the BT_REF_CLK_IN pin, the system clock both as a sine

wave clock and as a digital clock. For configuration, see Ta bl e 1 2 : pin BT_VDD_CLD (E6).

Table 3. DC input specification

Symbol Parameter Min. Typ. Max. Unit

VIL_BT Low level input voltage -0.2 - 0.35 *

BT_VIO_x V

VIH_BT High level input voltage 0.65 *

BT_VIO_x -

(BT_VIO_x

+ 0.2) and

( 2.85)

Cin_BT Input capacitance(1)

1. Except for the system clock.

1-2.5pF

Rpu Pull-up equivalent resistance

(with Vin = 0 V) 31 47 73 k

Rpd Pull-down equiv. resistance (with Vin = BT_VIO_x) 29 50 100 k

Vhyst

Schmitt trigger hysteresis (at BT_VIO_A = 1.8 V)

except for BT_CONFIG1-3, BT_RESETN,

BT_WAKEUP

0.4 0.5 0.6 V

Vhyst

Schmitt trigger hysteresis (at BT_VIO_x = 1.8 V)

for BT_CONFIG1-3, BT_RESETN, BT_WAKEUP,

BT_LP_CLK

0.223 - 0.314 V

Vhyst Schmitt trigger hysteresis (at BT_VIO_B = 1.3 V) 0.2 - 0.3 V

Table 4. DC output specification

Symbol Parameter Condition Min. Typ. Max. Unit

VOL_BT Low level output voltage Id = X(1) mA

1. X is the source/sink current under worst-case conditions according to the drive capabilities (see Section 3)

--0.15V

VOH_BT High level output voltage Id = X(1) mA BT_VIO_x

- 0.25 --V

Table 5. System clock supported frequencies

Symbol Parameter Values Unit

FIN Clock input frequency list 9.6, 10, 13, 16, 16.8, 19.2,

26, 33.6, 38.4 MHz

Table 6. System clock overall specifications

Symbol Parameter Min. Typ. Max. Unit

FINTOL Tolerance on input frequency -20 - 20 ppm

STA2500D Quick reference data

Doc ID 16067 Rev 3 9/58

Table 7. System clock, sine wave specifications

Symbol Parameter Min. Typ. Max. Unit

VPP Peak to peak voltage range 0.27 0.5 1.8 V

NHTotal harmonic content of input signal - - -25 dBc

ZINRe Real part of parallel input impedance at pin 30 60 90 k

ZINIm Imaginary part of parallel input impedance at pin - 5 8 pF

ZIDRe

Real impedance discrepancy between active and non-

active mode of clock input -- 7k

ZIDim

Imaginary impedance discrepancy between active and

non-active mode of clock input --500fF

Phase noise @ 10 kHz(1) ---126dBc/Hz

1. Equivalent to max 10 ps time jitter (rms).

Table 8. System clock, digital clock DC specifications

Symbol Parameter Min. Typ. Max. Unit

VIL Low level input voltage -0.2 - 0.35 *

BT_VDD_CLD V

VIH High level input voltage 0.65 *

BT_VDD_CLD -

(BT_VDD_CLD

+ 0.2) and

(2.85)

CIN Input capacitance - 5 8 pF

Table 9. System clock, digital clock AC specifications

Symbol Parameter Min. Typ. Max. Unit

TRISE 10% - 90% rise time - 1.5 6 ns

TFALL 90% - 10% fall time - 1.5 6 ns

DCYCLE Duty cycle 45 50 55 %

- Phase noise @ 10 kHz(1) - - -121 dBc/Hz

1. Equivalent to max 15 ps time jitter (rms).

Table 10. Low power clock specifications

The low power clock pin is powered by connecting BT_VIO_B to the wanted supply.

Symbol Parameter Min. Typ. Max. Unit

FIN Clock input frequencies 3.2, 32, 32.768 kHz

- Duty cycle 30 - 70 %

- Tolerance on input frequency 250 - 250 ppm

VIL Low level input voltage - - 0.35 *

BT_VIO_B V

VIH High level input voltage 0.65 *

BT_VIO_B --V

Vhyst Schmitt trigger hysteresis (BT_VIO_B = 1.8 V) 0.4 0.5 0.6 V

Quick reference data STA2500D

10/58 Doc ID 16067 Rev 3

2.5 Current consumption

Tamb = 25°C, 13 MHz digital clock, 7 dBm output power for BR packets, 3 dBm output power

for EDR packets.

Vhyst Schmitt trigger hysteresis (BT_VIO_B = 1.3 V) 0.2 0.3 0.4 V

CIN Input capacitance 1 - 2.5 pF

TRISE 10% - 90% rise time(1) --1s

TFALL 90% - 10% fall time(1) --1s

- Total jitter(2) - - 250 ppm

1. The rise and fall time are not the most important parameters for the low power clock input due to the Schmitt trigger logic. It

is more important that the noise on the Low power clock line remains substantially below the hysteresis in amplitude.

2. The total jitter is defined as the error that can appear on the actual frequency between two clock edges compared to the

perfect frequency. Due to this, the total jitter value must contain the jitter itself and the error due to the accuracy on the

clock frequency. The lower the accuracy, the smaller the jitter is allowed to be.

Table 10. Low power clock specifications (continued)

The low power clock pin is powered by connecting BT_VIO_B to the wanted supply.

Symbol Parameter Min. Typ. Max. Unit

Table 11. Current consumption(1)

State Typ. Unit

Complete Power Down 1 A

Deep Sleep mode 20 A

Functional Sleep mode(2) 1.2 mA

Sniff mode (1.28 s, 2 attempts, 0 timeouts), combined with H4 UART Deep Sleep

mode

(see section 6.10.3)

Master mode

Slave mode

A

Inquiry scan (1.28 seconds period), combined with H4 UART Deep Sleep mode

(see section 6.10.3) 318 A

HW Page scan (1.28 seconds period), combined with H4 UART Deep Sleep mode

(see section 6.10.3) 312 A

HW Inquiry and Page scan (1.28 seconds period), combined with H4 UART Deep

Sleep mode

(see section 6.10.3) 591 A

Idle ACL connection (Master) 3.6 mA

Idle ACL connection (Slave) 8.2 mA

Active: audio (HV3) Master (not sniffed) 11.7 mA

Active: audio (HV3) Slave (Sniff 1.28 s, 2 attempts, 0 timeouts) 10.6 mA

Active: data (DH1) Master or Slave

(172.8 kbps asymmetrical in TX mode)

(172.8 kbps symmetrical)

28.5 mA

STA2500D Quick reference data

Doc ID 16067 Rev 3 11/58

Active: data (DH5) Master or Slave

(723.2 kbps asymmetrical in TX mode)

(433.9 kbps symmetrical)

35.4

Active: data (2-DH5) Master or Slave (869.7 kbps symmetrical) 35.4 mA

Active: data (3-DH5) Master or Slave (1306.9 kbps symmetrical) 35.4 mA

Active: audio eSCO (EV3), (64 kbps symmetrical TeSCO = 6)

Master mode

Slave mode

Active: audio eSCO (2-EV3), (64 kbps symmetrical TeSCO = 12)

Master mode

Slave mode

7.8

11.7

Active: audio eSCO (3-EV3), (64 kbps symmetrical TeSCO = 18)

Master mode

Slave mode

6.5

10.5

Active: audio eSCO (EV5), (64 kbps symmetrical TeSCO = 36), Master mode 8 mA

Active: audio eSCO (EV5), (64 kbps symmetrical TeSCO = 36), Slave mode 11.9 mA

Active: audio eSCO (2-EV5), (64 kbps symmetrical TeSCO = 36), Master mode 6.3 mA

Active: audio eSCO (3-EV5), (64 kbps symmetrical TeSCO = 36), Master mode 5.75 mA

1. The power consumption (except for power safe modes i.e. complete power down and deep sleep mode)

will rise (with approx. 200 µA) if an analog system clock is used instead of a digital clock.

2. In functional sleep mode, the baseband clock is still running.

Table 11. Current consumption(1) (continued)

State Typ. Unit

Block diagram and electrical schematic STA2500D

12/58 Doc ID 16067 Rev 3

3 Block diagram and electrical schematic

Figure 1. Block diagram and electrical schematic

Filter

RECEIVER

TRANSMITTER

AUTOCALIBRATION

DEMO-

DULATOR

MODU-

LATOR

PLL

BASEBAND

CORE

EBC

ARM7TDMI

CPU Wrapper

RAM

ROM

AMBA

PERIPH.

BUS

UART/

SPI

INTERNAL SUPPLY MANAGEMENT

TIMER

INTERRUPT

PCM

WLAN

BT_RFP

BT_RFN

BT_REF_CLK_IN

RF PLL

Fractional N

CONTROL

AND

JTAG

I2C

BT_HV[1:0] BT_VIO_A BT_VIO_B

BT_GPIO/JTAG

[4:0]

BT_LP_CLK

BT_HOST_WAKEUP/

BT_SPI_INT

BT_WAKEUP

BT_RESETN

BT_UART/BT_SPI

[3:0]

BT_PCM

[3:0]

BT_CONFIG

[2:0]

BT_CLK_REQ_IN

[1:0]

BT_CLK_REQ_OUT

[1:0]

BT_GPIO_0

BT_VDD[4:0]

BT_TEST[1:0] BT_VDD_CLD BT_AF_PRG BT_VSS[5:0]

STA2500D Pinout

Doc ID 16067 Rev 3 13/58

4 Pinout

Figure 2. Pinout (bottom view)

4.1 Pin description and assignment

Ta bl e 1 2 shows the pin list of the STA2500D.

In columns “Reset” and “Default after reset”, the “PD/PU” shows the pads implementing an

internal pull-down/up.

The column “Reset” shows the state of the pins during hardware reset; the column “Default

after reset” shows the state of the pins after the hardware reset state is left, but before any

software parameter download.

The column “Type” describes the pin directions:

– I for Input (All inputs have a Schmitt trigger function.)

– O for Output

– I/O for Input/Output

– O/t for tri-state output

JTAG_TCK

GPIO_0

GPIO_3

7654321

BT_RESETNBT_REF_CLK_IN

BT_LP_CLK

BT_HOST_WAKEUP

/BT_SPI_INT

BT_WAKEUP

BT_UART_TXD

/ BT_SPI_DO

BT_UART_RXD

/ BT_SPI_DI

BT_UART_CTS

/ BT_SPI_CLK

BT_VIO_B

BT_UART_RTS

/ BT_SPI_CS

BT_PCM_SYNC

BT_PCM_CLKBT_PCM_A

BT_PCM_B

BT_GPIO_9

BT_VSSRF

BT_GPIO_10

BT_GPIO_11

BT_GPIO_16

BT_VSSANA

BT_CLK_REQ_IN_1

BT_CLK_REQ_IN_2

BT_CLK_REQ_OUT_1

BT_CONFIG_1

BT_CONFIG_3 BT_CONFIG_2

BT_RFPBT_RFNBT_HVA

BT_HVDBT_VDD_DBT_VIO_A

BT_VDD_CLD

BT_VDD_DSM

BT_VDD_N

BT_VDD_CL

BT_VDD_RF

BT_VSSDIGBT_VSSDIGBT_AF_PRG

BT_VSSANABT_VSSANA BT_TEST1

BT_TEST2

BT_CLK_REQ_OUT_2

BT_VSSRF

BT_GPIO_8

BT_GPIO_0

Pinout STA2500D

14/58 Doc ID 16067 Rev 3

For the output pin the default drive capability is 2 mA, except for pin K3 (BT_GPIO_11) and

pin L3 (BT_GPIO_8) where it is 8 mA such that when used for Class 1, these 2 pins can be

used for a switch control in a cheaper way.

Table 12. The STA2500D pin list (functional and supply)

Name Pin

#Description Type Reset(1) Default(2)

after reset

Clock and reset pins

BT_RESETN D3 Global reset - active low - -

BT_REF_CLK_IN D6 Reference clock input(3) I Input Input

BT_LP_CLK G3 Low power clock input - -

SW initiated low power mode

BT_CLK_REQ_OUT_1 C4 Wake-up signal to Host (Active high or Active

low, depending on configuration pins)

I/O(4)

Input PD/PU,

depends on

config

Output

depends on

config

BT_CLK_REQ_OUT_2 G7 Wake-up signal to Host. Active low

(SPI mode only) Input PU I/O depends

on config

BT_CLK_REQ_IN_1 E6 Clock request input (Active high) Input PD Input PD

BT_CLK_REQ_IN_2 G6 Clock request input (Active low) Input PU Input PU

BT_HOST_WAKEUP/

BT_SPI_INT F7 Wake-up signal to Host or SPI interrupt Input PD Output

BT_WAKEUP C5 Wake-up signal to Bluetooth (Active high) I/O Input

(5) Input

UART interface

BT_UART_RXD/

BT_SPI_DI F5 UART receive data

I/O

(4)

Input PD

SPI data in Input PD

BT_UART_TXD/

BT_SPI_DO F6 UART transmit data Output high

SPI data out Input PD

BT_UART_CTS/

BT_SPI_CLK G4 UART clear to send

Input PU

SPI clock Input PD

BT_UART_RTS/

BT_SPI_CSN F4 UART request to send Output low

SPI chip select Input PU

PCM interface

BT_PCM_SYNC C2 PCM frame signal

I/O

(4)

Input PD Input PD

BT_PCM_CLK D1 PCM clock signal

BT_PCM_A D2 PCM data

BT_PCM_B E1 PCM data

JTAG interface

BT_GPIO_9 B1 JTAG_TDI or GPIO - Input PU(6) Input PU(6)

STA2500D Pinout

Doc ID 16067 Rev 3 15/58

BT_GPIO_11 B2 JTAG_TDO or GPIO - Input PD(6) Input PD(6)

BT_GPIO_10 C1 JTAG_TMS or GPIO I/O

(4)

Input PD(6) Input PD(6)

BT_GPIO_16 B3 JTAG_NTRST (Active low) or Alternate

function. - Input PD(6) Input PD(6)

BT_GPIO_8 C3 JTAG_TCK or GPIO - Input PD(6) Input PD(6)

General purpose input/output pins

BT_GPIO_0 D5 General purpose I/O I/O

(4)

Input PD Input PD

Configuration pins

BT_CONFIG_1 E2 - - -

BT_CONFIG_2 F1 Configuration signal I Input Input

BT_CONFIG_3 F2 - - -

RF signals

BT_RFP A3 Differential RF port I/O --

BT_RFN A4 - -

Power supply

BT_HVA A7 Power supply (Connect to 2.75 V) - - -

BT_HVD G1

BT_VIO_A G5 1.65 V to 2.85 V I/Os supply(7) -- -

BT_VIO_B F3 1.17 V to 2.85 V I/Os supply(7) -- -

BT_VDD_CLD E7

System clock supply

1.65 V to 2.85 V

(Connect to BT_VIO_A in case of a digital

reference clock input, to BT_VSSANA in case

of an analog reference clock input.)

-- -

BT_VSSDIG E3 Digital ground - - -

BT_VSSANA

Analog ground - - -B6

BT_VSSRF A2 RF ground - - -

BT_VDD_CL D7

Internal supply decoupling/Regulator output.

Need 220nF decoupling capacitor to

BT_VSSANA.

-- -

Table 12. The STA2500D pin list (functional and supply) (continued)

Name Pin

#Description Type Reset(1) Default(2)

after reset

Pinout STA2500D

16/58 Doc ID 16067 Rev 3

4.2 HW configuration of the STA2500D

By means of the three configuration pins, one can select the Host interface (UART or SPI)

and clock request signal polarity to be used at startup.

The available combinations of Host interface and protocol are illustrated in Ta bl e 1 3 (where

‘1’ = BT_VIO_A and ‘0’ = BT_VSSDIG). Additionally, the polarity of the BT_CLK_REQ

signals can be programmed through the same pins. The polarity of the BT_CLK_REQ_IN

and BT_CLK_REQ_OUT signals is further described in Section 6.8.

BT_VDD_D G2

Internal supply decoupling/Regulator output.

Need 220nF decoupling capacitor to

BT_VSSDIG.

-- -

BT_VDD_DSM B7

Internal supply decoupling/Regulator output.

Need 220nF decoupling capacitor to

BT_VSSANA.

-- -

BT_VDD_N C7

Internal supply decoupling/Regulator output.

Need 220nF decoupling capacitor to

BT_VSSANA.

-- -

BT_VDD_RF A1

Internal supply decoupling/Regulator output.

Need 220nF decoupling capacitor to

BT_VSSRF.

-- -

Other pins

BT_TEST1 B5 Test pin I/O Input (8) Input

(8)

BT_TEST2 A6

BT_AF_PRG E5 Test pin (Leave unconnected)(9) I/O Open Open

1. Pin behaviour during HW reset (BT_RESETN low).

2. Pin behaviour immediately after HW reset and internal chip initialization, but before SW parameter download.

3. See also pin BT_VDD_CLD in Table 12.

4. Reconfigurable I/O pin.The functionality of these I/Os can be configured through software parameter download (see

Section 7.5).

5. Should be strapped to BT_VSSDIG if not used.

6. JTAG mode.

7. Described in Section 4.3.

8. To be strapped to BT_VSSANA.

9. Pin is ST - reserved for test function and it must be soldered to an isolated pad (not connected to anything, just floating).

Table 12. The STA2500D pin list (functional and supply) (continued)

Name Pin

#Description Type Reset(1) Default(2)

after reset

STA2500D Pinout

Doc ID 16067 Rev 3 17/58

4.3 I/O Supply

The device STA2500D has two different I/O supplies: BT_VIO_A and BT_VIO_B.

The two different pins may be potentially connected to separate dedicated voltage supplies

in order to harmonize the digital levels to the platform.

They are linked to different interfaces as described in Ta b l e 1 4 .

Table 13. Configuration programming

BT_CONFIG_1 BT_CONFIG_2 BT_CONFIG_3

Communication

Protocol

BT_CLK_REQ_OUT_1 BT_CLK_REQ_OUT_2

0 1 0 H4 UART Active high Depending on SW

config

0 1 1 H4 UART Active low Depending on SW

config

1 1 0 Reserved Reserved Reserved

1 1 1 Reserved Reserved Reserved

1 0 0 Reserved Reserved Reserved

1 0 1 Enhanced H4 SPI(1) Active high Active low

0 0 1 Reserved Reserved Reserved

0 0 0 Reserved Reserved Reserved

1. In order to get other SPI modes, the Host must send a specific configuration at start-up in addition of these configuration

pins.

Table 14. I/O supply split diagram

I/O supply

name

Voltage

range [V] Function Associated pins

BT_VIO_A 1.65 - 2.85

Configuration BT_CONFIG_1, BT_CONFIG_2, BT_CONFIG_3

Control

BT_WAKEUP

BT_RESETN

BT_CLK_REQ_OUT_1, BT_CLK_REQ_OUT_2

GPIO (JTAG)

BT_GPIO_8 (JTAG_TCK), BT_GPIO_9 (JTAG_TDI),

BT_GPIO_10 (JTAG_TMS), BT_GPIO_11 (JTAG_TDO),

BT_GPIO_16 (JTAG_NTRST)

PCM BT_PCM_A, BT_PCM_B, BT_PCM_SYNC, BT_PCM_CLK

Control BT_REG_CTRL

UART (SPI)

BT_UART_RXD (SPI_DI), BT_UART_TXD (SPI_DO),

BT_UART_RTS (SPI_CSN), BT_UART_CTS (SPI_CLK),

BT_HOST_WAKEUP (SPI_INT)

Control (GPIO) BT_CLK_REQ_IN_1 (GPIO_1), BT_CLK_REQ_IN_2 (GPIO_2)

GPIO BT_GPIO_0

BT_VIO_B 1.17 - 2.85 Low - power clock BT_LP_CLK

Functional description STA2500D

18/58 Doc ID 16067 Rev 3

5 Functional description

5.1 Transmitter

The transmitter uses the serial transmit data from the Bluetooth Controller. The transmitter

modulator converts this data into GFSK, /4-DQPSK or 8-DPSK modulated I and Q digital

signals for respectively 1, 2 and 3 Mbps transmission speed. These signals are then

converted to analog signals that are low pass filtered before up-conversion. The carrier

frequency drift is limited by a closed loop PLL.

5.2 Receiver

The STA2500D implements a low-IF receiver for Bluetooth modulated input signals. The

radio signal is taken from a balanced RF input and amplified by an LNA. The mixers are

driven by two quadrature LO signals, which are locally generated from a VCO signal running

at twice the frequency. The I and Q mixer output signals are band pass filtered by a poly-

phase filter for channel filtering and image rejection. The output of the band pass filter is

amplified by a VGA to the optimal input range for the A/D converter. Further channel filtering

is done in the digital part. The digital part demodulates the GFSK, /4-DQPSK or 8-DPSK

coded bit stream by evaluating the phase information. RSSI data is extracted. Overall

automatic gain amplification in the receive path is controlled digitally. The RC time constants

for the analog filters are automatically calibrated on chip.

5.3 PLL

The on chip VCO is part of a PLL. The tank resonator circuitry for the VCO is completely

integrated without need of external components. Variations in the VCO centre frequency are

calibrated out automatically.

STA2500D Functional description

Doc ID 16067 Rev 3 19/58

5.4 Bluetooth controller V1.2 and V2.0 + EDR features

The Bluetooth controller is backward compatible with the Bluetooth specification V1.2 [] and

V2.0 + EDR []. Here below is a list with the main features of those specifications:

●Adaptive Frequency Hopping (AFH): hopping kernel, channel assessment as Master

and as Slave

●Fast Connection: Interlaced scan for Page and Inquiry scan, answer FHS at first

reception, RSSI used to limit range

●Extended SCO (eSCO) links: supports EV3, EV4 and EV5 packets

●Channel Quality Driven Data Rate change (CQDDR)

●QoS Flush

●Synchronization: BT clocks are available at HCI level for synchronization of parallel

applications on different Slaves

●L2CAP Flow & Error control

●LMP SCO handling

●2 Mbps packet types

– ACL: 2-DH1, 2-DH3, 2-DH5

– eSCO: 2-EV3, 2-EV5

●3 Mbps packet types

– ACL: 3-DH1, 3-DH3, 3-DH5

– eSCO: 3-EV3, 3-EV5

5.5 Bluetooth controller V2.1 + EDR (“Lisbon”)

●Encryption Pause/Resume (EPR)

●Extended Inquiry Response (EIR)

●Link Supervision Time Out (LSTO)

●Secure Simple Pairing

●Sniff Subrating

●Quality of Service (Qos)

– Packet Boundary Flag

– Erroneous Data Delivery

5.6 Processor and memory

●ARM7TDMI

●On chip RAM, including provision for patches

●On chip ROM, preloaded with SW up to HCI

Functional description STA2500D

20/58 Doc ID 16067 Rev 3

5.7 TX output power control

The STA2500D supports output power control with advanced features:

●Basic feature:

– With the standard TX power control algorithm enabled, the STA2500D will adapt

its output power when a remote BT device supports the RSSI feature; this allows

the remote device to measure the link strength and to request the STA2500D to

decrease/increase its output power. In case the remote device does not support

the RSSI feature, the STA2500D will use its ‘default’ output power level.

●Advanced features, available via specific HCI commands:

– Enhanced power control feature: allows the STA2500D to decrease autonomously

its output power until the remote BT device, supporting the RSSI feature, requests

to increase the output power.

STA2500D General specification

Doc ID 16067 Rev 3 21/58

6 General specification

All the values are provided according to the Bluetooth specification V2.1 + EDR (“Lisbon”)

unless otherwise specified. The below values are preliminary and will be updated in the next

version of this datasheet.

6.1 Receiver

All specifications below are given at device pin level and with the conditions as specified.

Parameters are given for each of the 3 modulation types supported.

Typical is defined at T

amb

= 25 °C, BT_HV = 2.75 V. Minimum and Maximum are worst cases

over corner lots and temperature. Parameters are given at device pin, except for receiver

interferers measured at antenna with a filter having a typical attenuation of 2.3 dB.

Table 15. Mbps receiver parameters - GFSK

Symbol Parameter Test condition Min. Typ. Max. Unit

RFin Input frequency range - 2402 - 2480 MHz

RXsensC Receiver sensitivity

(Clean transmitter) @ BER 0.1% - -88 -86 dBm

RXsensD Receiver sensitivity

(Dirty transmitter) @ BER 0.1% - -87 -84 dBm

RXmax Maximum useable input signal

level @ BER 0.1% - 10 15 dBm

Receiver blocking performance @ BER 0.1% on Channel 58 (without Filter)

-signal in GSM band 900 MHz

(824 MHz to 960 MHz)

@ Input signal

strength = -67 dBm --15-dBm

-signal in GSM band 1800 MHz

(1805 MHz to 1990 MHz)

@ Input signal

strength = -67 dBm - -2.5 - dBm

-signal in WCDMA band

(2010 MHz to 2170 MHz)

@ Input signal

strength = -67 dBm --1.5-

dBm

Receiver interferer performance @ BER 0.1%

C/Ico-channel Co-channel interference @ Input signal

strength = -60 dBm -9.511dB

C/I1MHz Adjacent (±1 MHz) interference @ Input signal

strength = -60 dBm --90dB

C/I+2MHz Adjacent (+2 MHz) interference @ Input signal

strength = -60 dBm --40-30dB

C/I-2MHz Adjacent (-2 MHz) interference @ Input signal

strength = -67 dBm --26-9dB

C/I+3MHz Adjacent (+3 MHz) interference @ Input signal

strength = -67 dBm - -46.5 -40 dB

General specification STA2500D

22/58 Doc ID 16067 Rev 3

Typical is defined at T

amb

= 25 °C, BT_HV = 2.75 V. Minimum and Maximum are worst cases

over corner lots and temperature. Parameters are given at device pin, except for receiver

interferers measured at antenna with a filter having a typical attenuation of 2.3 dB.

C/I-3MHz Adjacent (-3 MHz) interference @ Input signal

strength = -67 dBm --43-20dB

C/I



4MHz

Adjacent (±4 MHz)

interference

@ Input signal

strength = -67 dBm --48-40dB

Receiver inter-modulation

IMD Inter-modulation Measured as defined in BT

test specification []. -39 -32 = dBm

Table 15. Mbps receiver parameters - GFSK (continued)

Symbol Parameter Test condition Min. Typ. Max. Unit

Table 16. Mbps receiver parameters - /4-DQPSK

Symbol Parameter Test condition Min. Typ. Max. Unit

RFin Input frequency range = 2402 2480 MHz

RXsensC Receiver sensitivity

(Clean transmitter) @ BER 0.01% - -87 -85 dBm

RXsensD Receiver sensitivity

(Dirty transmitter) @ BER 0.01% - -86.5 -84.5 dBm

RXmax Maximum useable input signal

level @ BER 0.1% -15 -9 - dBm

Receiver blocking performance @ BER 0.1% on channel 58 (without Filter)

-signal in GSM band 900 MHz

(824 MHz to 960 MHz)

@ Input signal

strength = -67 dBm - -15.5 - dBm

-signal in GSM band 1800 MHz

(1805 MHz to 1990 MHz)

@ Input signal

strength = -67 dBm - -3.5 - dBm

-signal in WCDMA band

(2010 MHz to 2170 MHz)

@ Input signal

strength = -67 dBm - -2.5 - dBm

Receiver interferer performance @ BER 0.1%

C/Ico-channel Co-channel interference @ Input signal

strength = -60 dBm -1113dB

C/I1MHz Adjacent (1 MHz) interference @ Input signal

strength = -60 dBm - -11.5 0 dB

C/I+2MHz Adjacent (+2 MHz) interference @ Input signal

strength = -60 dBm --40 -30 dB

C/I-2MHz Adjacent (-2 MHz) interference @ Input signal

strength = -67 dBm --20-7dB

C/I+3MHz Adjacent (+3 MHz) interference @ Input signal

strength = -67 dBm - -48.5 -40 dB

STA2500D General specification

Doc ID 16067 Rev 3 23/58

Typical is defined at T

amb

= 25 °C, BT_HV = 2.75 V. Minimum and Maximum are worst cases

over corner lots and temperature. Parameters are given at device pin, except for receiver

interferers measured at antenna with a filter having a typical attenuation of 2.3 dB.

C/I-3MHz Adjacent (-3 MHz) interference @ Input signal

strength = -67 dBm --47-20dB

C/I



4MHz

Adjacent (±4 MHz)

interference

@ Input signal

strength = -67 dBm --48-40dB

Table 16. Mbps receiver parameters - /4-DQPSK (continued)

Symbol Parameter Test condition Min. Typ. Max. Unit

Table 17. Mbps receiver parameters - 8-DPSK

Symbol Parameter Test condition Min. Typ. Max. Unit

RFin Input frequency range - 2402 - 2480 MHz

RXsensC Receiver sensitivity

(Clean transmitter) @ BER 0.01% - -79.5 -77.5 dBm

RXsensD Receiver sensitivity

(Dirty transmitter) @ BER 0.01% - -77 -74.5 dBm

RXmax Maximum useable input signal

level @ BER 0.1% -20 -15 - dBm

Receiver blocking performance @ BER 0.1% on channel 58 (without Filter)

-Signal in GSM band 900 MHz

(824 MHz to 960 MHz)

@ Input signal

strength = -67 dBm --20-dBm

-Signal in GSM band 1800 MHz

(1805 MHz to 1990 MHz)

@ Input signal

strength = -67 dBm - -14.5 - dBm

-Signal in WCDMA band

(2010 MHz to 2170 MHz)

@ Input signal

strength = -67 dBm --14-dBm

Receiver interferer performance @ BER 0.1%

C/Ico-channel Co-channel interference @ Input signal

strength = -60 dBm -1921dB

C/I1MHz Adjacent (±1 MHz) interference @ Input signal

strength = -60 dBm --45dB

C/I+2MHz Adjacent (+2 MHz) interference @ Input signal

strength = -60 dBm --37-25dB

C/I-2MHz Adjacent (-2 MHz) interference @ Input signal

strength = -67 dBm --120dB

C/I+3MHz Adjacent (+3 MHz) interference @ Input signal

strength = -67 dBm --46-33dB

C/I-3MHz Adjacent (-3 MHz) interference @ Input signal

strength = -67 dBm --40-13dB

C/I



4MHz

Adjacent (±4 MHz)

interference

@ Input signal

strength = -67 dBm --43-33dB

General specification STA2500D

24/58 Doc ID 16067 Rev 3

6.2 Transmitter

Unless otherwise stated, typical is defined at T

amb

= 25 °C, BT_HV = 2.75 V. Minimum and

Maximum are worst cases over corner lots and temperature. Parameters are given at device

pin, except for in-band spurious measured at antenna.

Table 18. Transmitter parameters

Symbol Parameter Test condition Min. Typ. Max. Unit

RFout Output frequency range - 2402 - 2480 MHz

RF Transmit Power

TXpout

(GFSK) Maximum output power(1) @ 2402 - 2480 MHz

@ 25 °C 6 8 10 dBm

TXpout

(GFSK) Maximum output power(1)

@ 2402 - 2480 MHz

@ worst cases over

corner lots and

temperature

4.5 8 10.5 dBm

TXpout

(GFSK) Minimum output power @ 2402 - 2480 MHz -52.5 -47.5 -42.5 dBm

TXpout

(/4-DQPSK) Maximum output power(1) (2) @ 2402 - 2480 MHz

@ 25 °C 3.5 6 8 dBm

TXpout

(/4-DQPSK) Minimum output power(2) @ 2402 - 2480 MHz -43.5 -38.5 -33.5 dBm

TXpoutrel

(/4-DQPSK) Relative transmit power (3) @ 2402 - 2480 MHz - -0.2 - dB

TXpout

(8-DPSK) Maximum output power(1) (2) @ 2402 - 2480 MHz

@ 25 °C 3.5 6 8 dBm

TXpout

(8-DPSK) Minimum output power(2) @ 2402 - 2480 MHz -43.5 -38.5 -33.5 dBm

TXpoutrel

(8-DPSK) Relative transmit power (3) @ 2402 - 2480 MHz - -0.2 - dB

In-band spurious emission(4)

FCC FCC’s 20 dB BW - 900 930 950 kHz

ACP_2 Channel offset = ±2 MHz - - -43.5 -20 dBm

ACP_3 Channel offset = ±-3 MHz - - -52.5 -40 dBm

ACP_4 Channel offset ±4 MHz - - -54.5 -40 dBm

EDR_IBS_1 Channel offset = ±1 MHz (2 and

3 Mbps) - - -33.5 -26 dB

EDR_IBS_2 Channel offset = ±2 MHz (2 and

3 Mbps) ---31.5-20

dBm

EDR_IBS_3 Channel offset = ±3 MHz (2 and

3 Mbps) ---45-40

dBm

EDR_IBS_4 Channel offset = ±4 MHz (2 and

3 Mbps) ---50-40

dBm

STA2500D General specification

Doc ID 16067 Rev 3 25/58

Initial carrier frequency tolerance (for an exact reference)(5)

F |f_TX-f0| - - 0 - kHz

Carrier frequency stability(6)

|f_s| Carrier frequency stability - - 3.2 10 kHz

Carrier frequency drift(7)

|f_p1| One slot packet - - 12 25 kHz

|f_p3| Three slots packet - - 14 40 kHz

|f_p5| Five slots packet - - 14 40 kHz

Carrier frequency drift rate

(7)

|f/50us| Frequency drift rate - - 8/50 20/50 kHz/µs

Modulation accuracy

(6) (7)

(8)

f1avg Maximum modulation - 140 163 175 kHz

f2max Minimum modulation - 115 135 - kHz



f1avg/



f2avg

-0.80.9-

- 2-DH5 RMS DEVM - - 8 20 %

- 2-DH5 99% DEVM - - - 30 %

- 2-DH5 Peak DEVM - - 21 35 %

- 3-DH5 RMS DEVM - - 8 13 %

- 3-DH5 99% DEVM - - - 20 %

- 3-DH5 Peak DEVM - - 21 25 %

TX out of band emission

E850 Emission in GSM band 850 MHz BW = 200 kHz (7) (9) (10) --79-76dBm

E900 Emission in GSM band 900 MHz BW = 200 kHz (7) (9) (10) --79-76dBm

E1500 Emission in GPS band BW = 200 kHz (7) (9) (10) --85-84dBm

E1800

Emission in GSM band 1800 MHz

BW = 200 kHz (7) (9) (10) --87-84dBm

E1900

Emission in GSM band 1900 MHz

BW = 200 kHz (7) (9) (10) --87-84dBm

Ewcdma Emission in WCDMA band BW = 3.8 MHz (7) (9) (10) --78-75dBm

1. Lower transmit power (i.e. Class 2) can be obtained by programming the radio init power table via software parameter

download or an HCI command.

2. Power of GFSK part.

3. Relative power of EDR part compared to the GFSK part.

4. At antenna with maximum output power, filter attenuation of 2.3 dB.

5. Phase noise will add maximum [-10 kHz;10 kHz] for worst case clock 270 mVpp at 13 MHz.

6. Worst case clock 270 mVpp at 13 MHz. Measurement according to EDR RF test spec V2.0.E.3 [].

7. With maximum output power (BR or EDR).

8. Measured on reference design STLC2555_rev1.1 following eBOM and layout recommendations.

9. Measurement bandwidth.

10. Transmitting DH5 packets.

Table 18. Transmitter parameters (continued)

Symbol Parameter Test condition Min. Typ. Max. Unit

General specification STA2500D

26/58 Doc ID 16067 Rev 3

6.3 Class 1 operation

The STA2500D supports operation at Class 1 output power levels with the use of an

external PA. The operation of the external PA and antenna switch are controlled by the

following signals:

If Class 1 functionality is enabled through SW parameter download, then these 6 control

signals are available on the pins as indicated in Ta bl e 2 0 and Ta bl e 2 1 .

Configuration 2 allows to deploy the STA2500D in Class 1 mode, still maintaining the

necessary control signals to coexist and cooperate with a WLAN transceiver. The

handshake between the STA2500D and a WLAN device happens in this case through other

BT_GPIO pins.

6.4 Power-up

The BT_RESETN pin should be active while powering up BT_VDD_HV and should stay

active at least two cycles of the low power clock (BT_LP_CLK) after power-up is completed.

The time between the STA2500D making BT_CLK_REQ_OUT_x active and the platform

providing a stable clock should maximally be 15 ms.

Table 19. Output power: class 1 control signals

Control signal name Function

PAEN PA enable (active during TX slot)

PA_VAL0 Bit 0 of the power level delivered by the PA

PA_VAL1 Bit 1 of the power level delivered by the PA

RXEN LNA enable (if present)

AntSw Control of the antenna switch

edr_mode Indication to PA whether TX is EDR or BR

Table 20. Output power: class 1 device pin configuration (depending on SW

parameter download)

Function SW configuration 1 SW configuration 2

PAEN BT_HOST_WAKEUP BT_GPIO_16

PA_VAL0 BT_GPIO_0 BT_GPIO_10

PA_VAL1 BT_CLK_REQ_IN_1 BT_GPIO_9

RXEN BT_CLK_REQ_IN_2 BT_GPIO_8

AntSw (BT_GPIO_11) BT_GPIO_11

Table 21. Output power: class 1 device pin configuration (depending on SW

parameter download)

Function SW configuration a SW configuration b SW configuration c

edr_mode BT_CLK_REQ_OUT_1 BT_CLK_REQ_OUT_2 not available on a pin

STA2500D General specification

Doc ID 16067 Rev 3 27/58

6.5 System clock

The STA2500D works with a sine wave or digital clock provided on the BT_REF_CLK_IN

pin. Detailed specifications are found in Section 2.4.

6.6 Low power clock

The low power clock is used by the Bluetooth Controller as reference clock during the low

power modes. It requires an accuracy of +250 ppm. The STA2500D requires a digital clock

to be provided on the BT_LP_CLK pin, with frequencies of 3.2 kHz, 32 kHz and 32.768 kHz.

After power-up, the low power clock must be available before the reset is released. It must

remain active all the time until the STA2500D is powered off.

6.7 Clock detection

An integrated automatic detection algorithm detects the system and low power clock

frequencies after a hardware reset. The steps in the clock detection routine are:

●Identification of the system clock frequency (9.6 MHz, 10 MHz, 13 MHz, 16 MHz,

16.8MHz, 19.2 MHz, 26 MHz, 33.6 MHz or 38.4 MHz)

●Identification of the low power clock (3.2 kHz, 32.768 kHz or 32 kHz).

6.8 Clock request signals

To allow minimum power consumption, a clock request feature is available so that the

system clock (BT_REF_CLK_IN) can be stopped when not needed by the Bluetooth

system. The clock request signal can be active high or active low, and the STA2500D

supports internal propagation of clock request signal coming from another device in the

system.

Different configurations as described below are supported immediately after reset and in all

Bluetooth operation modes, provided that BT_VIO_A is available.

The clock request functionality is based on four different signals: BT_CLK_REQ_OUT_1,

BT_CLK_REQ_OUT_2, BT_CLK_REQ_IN_1, BT_CLK_REQ_IN_2, with the following

function:

●BT_CLK_REQ_OUT_1: active low or high clock request, depending on HW

configuration pins (Table ). Support for either push-pull or open drain output.

●BT_CLK_REQ_OUT_2: active low clock request, only used in combination with SPI

mode. Support for either push-pull or open drain output.

●BT_CLK_REQ_IN_1: active high clock request input from an other device, depending

on HW configuration pin.

●BT_CLK_REQ_IN_2: active low clock request input from an other device.

The following modes are supported:

●Active high clock request input and output combined with UART or SPI:

General specification STA2500D

28/58 Doc ID 16067 Rev 3

Figure 3. Active high clock request input and output combined with UART or SPI

●Active low clock request input and output combined with UART:

Figure 4. Active low clock request input and output combined with UART

●Active low clock request input and output combined with SPI:

Figure 5. Active low clock request input and output combined with SPI

The pins which are “not used” are available for alternate functions as described in

Section 7.5.

BT_CLK_REQ_OUT_1

BT_CLK_REQ_IN_1

Internal BT CLK Request

BT_CLK_REQ_IN_2

(*)

(*) BT_CLK_REQ_IN_1 and BT_CLK_REQ_IN_2 are used UNLESS one or both are re-programmed as alternate function(s) via Parameter File

(*)

NOT

BT_CLK_REQ_OUT_1

AND

BT_CLK_REQ_IN_1

Internal BT CLK Request

BT_CLK_REQ_IN_2

(*) BT_CLK_REQ_IN_1 and BT_CLK_REQ_IN_2 are used UNLESS one or both are re-programmed as alternate function(s) via Parameter File

(*)

NOT

BT_CLK_REQ_OUT_2

AND

BT_CLK_REQ_IN_1

Internal BT CLK Request

BT_CLK_REQ_IN_2

(*) BT_CLK_REQ_IN_1 and BT_CLK_REQ_IN_2 are used UNLESS one or both are re-programmed as alternate function(s) via Parameter File

(*)

NOT

Table 22. Use of the BT_CLK_REQ_IN and BT_CLK_REQ_OUT signals in different modes

BT_CONFIG_1 BT_CONFIG_2 BT_CONFIG_3 Protocol BT_CLK_

REQ_IN_1

BT_CLK_

REQ_IN_2

BT_CLK_R

EQ_OUT_1

BT_CLK_R

EQ_OUT_2

010H4 UART

Active

high(1)

Active

low(1) Active high not used

011H4 UART

Active

low(1)

Active

low(1) Active low not used

101

Enhanced

H4 SPI Active high Active low Active high Active low

1. BT_CLK_REQ_IN_1 and BT_CLK_REQ_IN_2 are used in the configuration logic, UNLESS one or both I/Os re-

programmed as alternate function(s) via the Parameter File.

STA2500D General specification

Doc ID 16067 Rev 3 29/58

6.9 Interrupts

The user can program the BT_GPIOs as external interrupt sources.

6.10 Low power modes

6.10.1 Overview

To save power, three low power modes are supported as described in Ta b le 2 3 .

Depending of the Bluetooth and of the Host's activity, the STA2500D decides to use Sleep

mode or Deep Sleep mode. Note however that the Deep Sleep mode must first be activated

via SW parameter download or an HCI command prior to any possibility to use it as the

default configuration is only Sleep mode. Complete Power Down is entered only after an

explicit command from the Host.

Table 23. Low power modes

Low power mode Description

Sleep mode

The STA2500D:

– Accepts HCI commands from the Host.

– Supports all types of Bluetooth links.

– Can transfer data over Bluetooth links.

– Dynamically switches between sleep and active mode when needed.

– The system clock is still active in part of the design.

– Parts of the chip are dynamically powered off depending on the Bluetooth activity.

Deep Sleep mode

The STA2500D:

– Does not accept HCI commands from the Host.

– Supports Page and Inquiry scans.

– Supports Bluetooth links that are in Sniff or Sniff Subrating.

– Dynamically switches between Deep Sleep and active mode during Bluetooth

activity. The Deep Sleep mode entry is initiated by the Host, the STA2500D

acknowledges or not. The wake-up mechanism must be enabled by a SW

parameter download before it can be used. More details in section 6.10.3.

– The system clock is not active in any part of the design.

– Parts of the chip are dynamically powered off depending on the Bluetooth activity.

Complete Power Down

The STA2500D is effectively powered down:

– No Bluetooth activity is supported.

– The HCI interface is shut down.

– The system clock is not active in any part of the design.

– Most parts of the chip are completely powered off.

– RAM content is not maintained (initialisation is required at wake-up).

– Some pins (UART/SPI I/Os and the 4 clock request signals and BT_GPIO_16)

keep their previous configuration (input or output, pull behaviour) during

Completed Power Down.

– The Complete Power Down entry is initiated by an HCI command followed by a

Deep Sleep command, this in order to ensure a smooth transition from active to

Complete Power Down state. In order to go out of this mode, either a HW reset or

BT_WAKEUP = ‘1’ is needed.

General specification STA2500D

30/58 Doc ID 16067 Rev 3

6.10.2 Some examples for the usage of the low power modes

Sniff or sniff subrating

The STA2500D is in active mode with a Bluetooth connection. Once the transmission is

concluded, Sniff or Sniff Subrating is programmed. When one of these two states is entered,

the STA2500D goes into Sleep mode. After that, the Host may decide to place the

STA2500D in Deep Sleep mode as described in Section 6.10.3. The Deep Sleep mode

allows for lower power consumption. When the STA2500D needs to send or receive a

packet (e.g. at Tsniff or at the beacon instant), the STA2500D requests the system clock and

enters active mode for the needed transmission/reception. Immediately afterwards, the

STA2500D will go back to Deep Sleep mode. If some HCI transmission is needed, the

UART/SPI link will be reactivated, using one of the four ways explained in Section 6.10.3

and the STA2500D will move from Deep Sleep mode to Sleep mode.

Inquiry/page scan

When only Inquiry scan or Page scan is enabled, the STA2500D will go in Sleep mode or

Deep Sleep mode outside the receiver activity. The selection between Sleep mode and

Deep Sleep mode depends on the UART/SPI activity as in Sniff or Sniff Subrating.

No connection

If the Host allows Deep Sleep mode (as described in Section 6.10.3) and there is no activity,

then the STA2500D puts itself in Deep Sleep mode. It is possible to exit the Deep Sleep

mode by using one of the four methods explained in Section 6.10.3. In this Deep Sleep

mode (no connection), the Host can also decide to put the STA2500D in Complete Power

Down to further reduce the power consumption. In this case some part of the STA2500D will

be completely powered off. The request to quit the Complete Power Down is done either by

putting the BT_WAKEUP signal to ‘1’ or with an HW reset.

Active link

When there is an active link ((e)SCO or ACL), the Bluetooth Controller will not go in Deep

Sleep mode and not in Complete Power Down. But the Bluetooth Controller is made in such

a way that whenever it is possible, depending on the scheduled activity (number of link, type

of link, amount of data exchanged), it goes in Sleep mode.

6.10.3 Deep sleep mode entry and wake-up

During periods of no activity on the Bluetooth and on the Host side, the chip can be placed

in Deep Sleep mode. Four ways to initiate Deep Sleep mode and to wake up are supported

(selection is done through software parameter download): they are respectively based on a

UART interface in the first case, an SPI interface in the second case and third case, while

either UART or SPI interfaces can be used in the fourth case that is based on an handshake

mechanism.

Deep sleep mode entry and wake up through H4 UART

It requires BT_CLK_REQ_OUT_1, BT_UART_RXD and BT_UART_RTS. The

BT_UART_RXD is used as wake-up signal from the Host, the BT_CLK_REQ_OUT_1

requires the clock from the Host and the BT_UART_RTS indicates when the STA2500D is

STA2500D General specification

Doc ID 16067 Rev 3 31/58

available. In this mode, the break function (BT_UART_RXD is low for more than 1 word) is

used to distinguish between normal operation and low power mode usage.

●Deep sleep mode entry

The Host tells the STA2500D that it can go in Deep Sleep mode power by forcing the

BT_UART_RXD of the STA2500D to '0' for more than 1 word. The STA2500D decides

to go in Deep Sleep mode, or not, depending on its scheduled activity and on the

number of events or data packets to be sent to the Host. In case it decides to go in

Deep Sleep mode, it signals it by forcing BT_UART_RTS high; then it asserts

BT_CLK_REQ_OUT_1 low to tell the Host that it does not need the clock anymore. The

STA2500D cannot go in Deep Sleep mode by itself. This is a logical consequence of

the fact that the system clock is needed to receive characters on the UART.

Note that when the system is in Deep Sleep mode, the UART is closed.

●Deep sleep mode wake-up

The wake-up procedure can be initiated by the Host or by the STA2500D. In the latter

case, it can be with or without communication, depending if there are data to be

transmitted to the Host.

1. Wake-up initiated by the Host

The Host sets the BT_UART_RXD pin of the STA2500D to '1'. Then the STA2500D

asks the Host to restart the system clock by setting BT_CLK_REQ_OUT_1 to '1'. When

the clock is available, the STA2500D confirms it is awake by releasing BT_UART_RTS

to '0'.

2. Autonomous wake-up with UART communication (i.e. initiated by the STA2500D)

The STA2500D first asks the Host to restart the system clock by setting

BT_CLK_REQ_OUT_1 to '1'.

When the clock is available, the STA2500D sets BT_UART_RTS low, and then the Host

can give confirmation by releasing the BT_UART_RXD of the STA2500D.

Another possibility is that the STA2500D sets BT_HOST_WAKEUP to ‘1’ to request the

Host attention. Then the Host can give confirmation by releasing the BT_UART_RXD of

the STA2500D and the STA2500D sets BT_UART_RTS low.

The choice between the two possibilities is selected by a software parameter.

3. Autonomous wake-up without UART communication (i.e. initiated by the STA2500D)

The STA2500D asks the Host to restart the system clock by setting

BT_CLK_REQ_OUT_1 to '1'.

General specification STA2500D

32/58 Doc ID 16067 Rev 3

Figure 6. Deep sleep mode entry and wake-up through H4 UART

Deep sleep mode entry and wake-up through enhanced H4 SPI

In this case no additional signals are needed to control the Deep Sleep mode and the wake-

up mechanism except for BT_CLK_REQ_OUT_x (BT_CLK_REQ_OUT_1 for active high

polarity and BT_ CLK_REQ_OUT_2 for active low polarity).

The enhanced H4 protocol makes use of three messages: SLEEP, WAKEUP and WOKEN.

More details on the enhanced H4 protocol can be found in Section 8.2.

●Deep sleep mode entry

Entering Deep Sleep mode can only be initiated by the Host sending a SLEEP

message to the Bluetooth Controller.

If that one accepts it, the device enters Deep Sleep mode: consequently the Bluetooth

Controller de-asserts BT_CLK_REQ_OUT_x and internally gates the system clock.

This is illustrated in Figure 7.

If there is still pending activity at the Bluetooth side on the air, the Bluetooth Controller

does not immediately enter Deep Sleep mode and therefore BT_CLK_REQ_OUT_x

stays 'active' during this period: however the Bluetooth Controller will go in Deep Sleep

mode at the end of the air activity.

If there is pending data to be transferred to the Host, the Bluetooth Controller will

request a data transfer: however the Bluetooth Controller will go in Deep Sleep mode at

the end of the data transfer.

●Deep sleep mode wake-up

Wake-up can be requested by the Host or autonomously by the Bluetooth Controller. In

the latter case, it can be with or without communication on the interface (i.e. during

Page scan, there is no data to transfer to the Host).

1. Wake-up initiated by the Host

In the case of a wake-up by the Host, it sends a WAKEUP command and waits for a

WOKEN response before starting the data exchange. Of course the Bluetooth

Controller must first request the system clock through BT_CLK_REQ_OUT_x.

It should be noted that the WAKEUP message is decoded in the Bluetooth Controller's

Active

Sleep Mode

Mode

UART off

UART on

HOST_WAKEUP=‘ 1’ or ‘ 0’

‘A’ : Active high/low

‘P’ : Passive low/high

BT Con tro ller :CLK_REQ_OUT_1=‘ P’

Active

Sleep Mode

Hos t: UART_ RXD=‘ 0’

BT Con troller : UART_ RTS =‘1’

UART offHos t: UART_ RXD=‘ 1’

BT Con troller : UART_ RTS =‘0’

HOST_WAKEUP=‘1’

BT Con tro ller :CLK_REQ_OUT_1=‘ A’

HOST_WAKEUP=‘ 0’

Hos t: UART_ RXD=‘ 1’

AND

BT Con troller : CLK_REQ_OUT_1=‘ A’

and

UART_ RTS=‘0’

Active

Sleep Mode

Deep Sleep

UART off

UART on

HOST_WAKEUP=‘ 1’ or ‘ 0’

BT_CLK_REQ_OUT_1 =

BT Con tro ller : BT_CLK_REQ_OUT_1=‘ P’

Active

Sleep Mode

Host: BT_UA RT_R XD =‘ 0’

BT Con troller : BT_ UA RT_ RTS=‘ 1’

UART offHost: BT_ UA RT_ RX D =‘ 1’

BT Con troller :BT_ UA RT_ RTS =‘0’

BT_HOST_WAKEUP=‘1’

BT Con tro ller :

BT_CLK_REQ_OUT_1

=‘ A’

HOST_WAKEUP=‘ 0’

Host: BT_UA RT_R XD=‘ 1’

AND

BT Controller: BT_CLK_REQ_OUT_1 =‘ A’

and

BT_UA RT_RTS=‘ 0’

STA2500D General specification

Doc ID 16067 Rev 3 33/58

SPI HW block even before the system clock is available. This block will generate an

interrupt, allowing the Bluetooth Controller to reply with a WOKEN message. This is

illustrated in Figure 8.

2. Autonomous wake-up with communication (i.e. initiated by the STA2500D)

In the case of an autonomous wake-up with data transmission, the Bluetooth Controller

sets BT_SPI_INT high to request the SPI interface and waits for BT_SPI_CSN going

low, indicating the SPI transaction starts. Of course the Bluetooth Controller must first

request the system clock through BT_CLK_REQ_OUT_x before being able to start the

process. This is illustrated in Figure 9. Note that the Bluetooth Controller goes back to

Deep Sleep mode at the end of the data transfer.

3. Autonomous wake-up without communication (i.e. initiated by the STA2500D)

For autonomous wake-up without SPI communication, the STA2500D only asserts

BT_CLK_REQ_OUT_x to get the system clock.

Figure 7. Entering deep sleep mode through enhanced H4 SPI

Figure 8. Wake-up by the host through enhanced H4 SPI

REF_CLK _IN

CLK _REQ_OUT _1

SPI_CLK

SPI_DI

SPI_DO

SPI_INT

SPI_CSN

SLEEP

REF_CLK _IN

CLK _REQ_OUT _1

SPI_CLK

SPI_DI

SPI_DO

SPI_INT

SPI_CSN

WAKEUP

WOKEN

General specification STA2500D

34/58 Doc ID 16067 Rev 3

Figure 9. Wake-up by the Bluetooth controller with data transmission to the host,

through enhanced H4 SPI

Deep sleep mode entry and wake-up through H4 SPI

It requires BT_CLK_REQ_OUT_x (BT_CLK_REQ_OUT_1 for active high polarity and

BT_CLK_REQ_OUT_2 for active low polarity), BT_WAKEUP and BT_SPI_INT. The

BT_WAKEUP is used as wake-up signal from the Host, the BT_CLK_REQ_OUT_x requires

the clock from the Host and BT_SPI_INT is used as a wake-up signal from the Bluetooth

Controller.

●Deep sleep mode entry

The Host tells the STA2500D that it can go in Deep Sleep mode by forcing the

BT_WAKEUP of the STA2500D to ‘0’. The STA2500D decides to go in Deep Sleep

mode, or not, depending on its scheduled activity and on the number of events or data

packets to be sent to the Host. In case it decides to go in Deep Sleep mode, it asserts

BT_CLK_REQ_OUT_x ‘inactive’ to tell the Host that it does not need the clock

anymore. The STA2500D cannot go in Deep Sleep mode by itself. Note that the Host

cannot force BT_WAKEUP to ‘0’ before the end of a write operation from the Host, this

in order to allow correct decoding of the message by the Bluetooth Controller.

●Deep sleep mode wake-up

The wake-up procedure can be initiated by the Host or by the STA2500D. In the latter

case, it can be with or without communication, depending if there are data to be

transmitted to the Host.

1. Wake-up initiated by the Host

The Host sets the BT_WAKEUP pin of the STA2500D to ‘1’. Then the STA2500D asks

the Host to restart the system clock by setting BT_CLK_REQ_OUT_x to ‘active’. When

the clock is available and stable, the Host can use BT_SPI_CSN to start an SPI

transaction if needed (there is a programmable minimum delay between the assertion

of BT_CLK_REQ_OUT_x and the moment the Host can assert BT_SPI_CSN).

2. Autonomous wake-up with SPI communication (i.e. initiated by the STA2500D)

The STA2500D first asks the Host to restart the system clock by setting

BT_CLK_REQ_OUT_x to ‘active’.

When the clock is available, the STA2500D sets BT_SPI_INT high to request the SPI

interface to the Host and waits for BT_SPI_CSN going low, indicating the SPI

transaction starts.

3. Autonomous wake-up without SPI communication (i.e. initiated by the STA2500D)

The STA2500D asks the Host to restart the system clock by setting

BT_CLK_REQ_OUT_x to ‘active’.

REF_CLK _IN

CLK _REQ_OUT_1

SPI_CLK

SPI_DI

SPI_DO

SPI_INT

SPI_CSN

DATA

STA2500D General specification

Doc ID 16067 Rev 3 35/58

Figure 10. Deep sleep mode entry and wake-up through H4 SPI

Deep sleep mode entry and wake-up through H4 UART or H4 SPI with

handshake

This method is supported by both H4 UART and H4 SPI. The description below is for H4

UART.

It requires BT_CLK_REQ_OUT_1, BT_WAKEUP and BT_HOST_WAKEUP. The

BT_WAKEUP is used as wake-up signal from the Host, the BT_CLK_REQ_OUT_1 requires

the clock from the Host and BT_HOST_WAKEUP is used as a wake-up signal from the

Bluetooth Controller.

●Deep sleep mode entry

The Host tells the STA2500D that it can go in Deep Sleep mode by forcing the

BT_WAKEUP of the STA2500D to ‘0’. The STA2500D decides to go in Deep Sleep

mode, or not, depending on its scheduled activity and on the number of events or data

packets to be sent to the Host. In case it decides to go in Deep Sleep mode, it asserts

BT_CLK_REQ_OUT_1 low to tell the Host that it does not need the clock anymore. On

the contrary, if it still wants the interface active for up-transmission, it keeps

BT_HOST_WAKEUP to ‘1’ as long as needed before de-asserting

BT_CLK_REQ_OUT_1. This is illustrated in Figure 11.

●Deep sleep mode wake-up

The wake-up procedure can be initiated by the Host or by the STA2500D. In the latter

case, it can be with or without communication, depending if there are data to be

transmitted to the Host.

1. Wake-up initiated by the Host

The Host sets the BT_WAKEUP pin of the STA2500D to ‘1’. Then the STA2500D asks

the Host to restart the system clock by setting BT_CLK_REQ_OUT_1 to ‘1’. When the

clock is available and stable, the STA2500D puts BT_UART_RTS low to allow

communication. In case the STA2500D wants to send events to the Host, it then puts

Active

Sleep Mode

Mode

SPI off

SPI on

HOST_WAKEUP=‘ 1’ or ‘ 0’

CLK_REQ_OUT_1 = ‘ A’ : Active high/low

‘P’ : Passive low/high

BT Con troller :CLK_REQ_OUT_1=‘ P’

Active

Sleep Mode

Host: BT_WAKEUP=‘0’

SPI off

Host: BT_WAKEUP=‘1’

BT Controller:SPI_INT=‘ 1’

BT Con troller :CLK_REQ_OUT_1=‘ A’

HOST_WAKEUP=‘ 0’

Host: BT_WAKEUP=‘1’

AND

BT Controller: CLK_REQ_OUT_1=‘ A ’

Active

Sleep Mode

Deep Sleep

Mode

SPI off

SPI on

HOST_WAKEUP =‘ 1’ or ‘ 0’

CLK_REQ_OUT_1 = ‘ A’ : Active high/low

‘P’ : Passive low/high

BT Controller:BT_CLK_ REQ_OUT_1=‘ P’

Active

Sleep Mode

Host: BT_WAKEUP=‘0’

SPI off

Host: BT_WAKEUP=‘1’

BT Controller: BT_SPI_INT =‘ 1 ’

BT Controller:BT_CLK_REQ_OUT_1=‘A’

HOST_WAKEUP=‘ 0’

Host: BT_WAKEUP=‘1’

AND

BT Controller:BT_CLK_REQ_OUT_1=‘ A’

General specification STA2500D

36/58 Doc ID 16067 Rev 3

BT_HOST_WAKEUP to ‘1’ in order to warm the Host and traffic starts when the Host

puts BT_UART_CTS to low. This is illustrated in Figure 12.

2. Autonomous wake-up with communication (i.e. initiated by the STA2500D)

The STA2500D first asks the Host to restart the system clock by setting

BT_CLK_REQ_OUT_1 to ‘1’.

When the clock is available, the STA2500D requests traffic by asserting

HOST_WAKEUP high. Then either it puts BT_UART_RTS low to start traffic exchange

directly or it waits for the Host to first assert BT_WAKEUP high. The selection in

between the two behaviours is done by a SW parameter in the Parameter File.

3. An autonomous wake-up without communication (i.e. initiated by the STA2500D)

The STA2500D asks the Host to restart the system clock by setting

BT_CLK_REQ_OUT_1 to ‘1’. The UART signals are not changing.

Figure 11. Entering deep sleep mode, pending data on UART interface, through

UART with handshake

1. Host puts BT_WAKEUP low. BT Controller notices it. But as there is pending traffic to

be send to Host, it keeps HOST_WAKEUP high as long as needed for up-transmission

and then de-asserts HOST_WAKEUP, telling the Host there is nothing more to

transmit.

2. BT Controller puts UART_RTS high to set “flow off”. This is done in fixed number of

instructions.

3. Then BT Controller puts CLK_REQ_OUT_1 to ‘0’, telling the Host it can cut the clock.

This is done in fixed number of instructions.

4. There is no clock, BT is in Deep Sleep mode.

REF_CLK_IN

CLK_REQ_OUT_1

BT_WAKEUP

UART_RTS

HOST_WAKEUP 3

REF_CLK_IN

CLK_REQ_OUT_1

BT_WAKEUP

UART_RTS

HOST_WAKEUP 3

STA2500D General specification

Doc ID 16067 Rev 3 37/58

Figure 12. Wakeup by host through UART with handshake

5. Host pulls BT_WAKEUP high to wake-up BT Controller. HW starts driving

CLK_REQ_OUT_1 high (after 2*LP_CLK).

6. Host starts 13 MHz clock and distribute it when stable. Delay between

CLQ_REQ_OUT_1 and usage of stable clock is programmable in between 3 and 39

ms.

7. When BT Controller starts with clock, it sets “flow on” by putting UART_RTS low. There

is a fixed SW latency. Host can send commands.

8. BT Controller sets HOST_WAKEUP high telling to the Host it has events to send to the

Host.

9. When the Host is ready for data transmission, it asserts UART_CTS low.

6.11 Patch RAM

The STA2500D includes a HW block that allows patching of the ROM code.

Additionally, a SW patch mechanism allows replacing complete SW functions without

changing the ROM image.

A part of the RAM memory is used for HW and SW patches.

6.12 Download of SW parameter file

To change the device configuration a set of customizable parameters have been defined

and put together in one file, the parameter file. This Parameter File is downloaded at start-

up into the STA2500D.

Examples of parameters are: radio configuration, PCM settings etc.

The same HCI command is used to download the file containing the patches (both those for

the SW and HW mechanism).

A more detailed description of the SW parameter file is available upon request.

REF_CLK_IN

CLK_REQ_OUT_1

BT_WAKEUP

UART_RTS

UART_CTS

UART_RTS

HOST_WAKEUP

UART_RTS

General specification STA2500D

38/58 Doc ID 16067 Rev 3

6.13 Bluetooth - WLAN coexistence in collocated scenario

The coexistence interface uses up to 4 WLAN control signal pins, which can be mapped via

software parameter download on different pins of the STA2500D (see Section 7.5).

The functionality of the 4 WLAN control signal pins depends on the selected algorithm, as

explained

below and summarized in Ta bl e 2 4 .

Bluetooth and WLAN 802.11 b/g [] [] technologies occupy the same 2.4 GHz ISM band. The

STA2500D implements a set of mechanisms to avoid interference in a collocated scenario.

The STA2500D supports 5 different algorithms in order to provide efficient and flexible

simultaneous functionality between the two technologies in collocated scenarios:

●Algorithm 1: PTA (Packet Traffic Arbitration) based coexistence algorithm defined in

accordance with the IEEE 802.15.2 recommended practice [].

●Algorithm 2: the WLAN is the Master and it indicates to the STA2500D when not to

operate in case of simultaneous use of the air interface.

●Algorithm 3: the STA2500D is the Master and it indicates to the WLAN chip when not

to operate in case of simultaneous use of the air interface.

●Algorithm 4: Two-wire mechanism

●Algorithm 5: Alternating Wireless Medium Access (AWMA), defined in accordance

with the WLAN 802.11 b/g [] [] technologies.

The algorithm is selected via an HCI command. The default algorithm is algorithm 1.

6.13.1 Algorithm 1: PTA (packet traffic arbitration)

The algorithm is based on a bus connection between the STA2500D and the WLAN chip:

Figure 13. PTA diagram

By using this coexistence interface it is possible to dynamically allocate bandwidth to the two

devices when simultaneous operations are required while the full bandwidth can be

allocated to one of them in case the other one does not require activity.

The algorithm involves

●a priority mechanism, which allows preserving the quality of certain types of link.

●a mechanism to indicate that a periodic communication is ongoing.

A typical application would be to guarantee optimal quality to the Bluetooth voice

communication while an intensive WLAN communication is ongoing.

Several algorithms have been implemented in order to provide a maximum of flexibility and

efficiency for the priority handling. ST specific HCI commands are implemented to select the

algorithm and to tune the priority handling.

STLC2500D WLAN

RF_REQUEST

STATUS

FREQ

RF_CONFIRM

STA2500D General specification

Doc ID 16067 Rev 3 39/58

The combination of time division multiplexing and the priority mechanism avoids the

interference due to packet collision. It also allows the maximization of the 2.4 GHz ISM

bandwidth usage for both devices while preserving the quality of some critical types of link.

6.13.2 Algorithm 2: WLAN master

In case the STA2500D has to cooperate, in a collocated scenario, with a WLAN chip not

supporting a PTA based algorithm, it is possible to put in place a simpler mechanism.

The interface is reduced to 1 line:

Figure 14. WLAN master

When the WLAN has to operate, it alerts high the BT_RF_NOT_ALLOWED signal and the

STA2500D will not operate while this signal stays high.

This mechanism permits to avoid packet collision in order to make an efficient use of the

bandwidth but cannot provide guaranteed quality over the Bluetooth links.

6.13.3 Algorithm 3: Bluetooth master

This algorithm represents the symmetrical case of algorithm 2. Also in this case the

interface is reduced to 1 line:

Figure 15. Bluetooth master

When the STA2500D has to operate it alerts high the WLAN_RF_NOT_ALLOWED signal

and the WLAN will not operate while this signal stays high.

This mechanism permits to avoid packet collision in order to make an efficient use of the

bandwidth, it provides high quality for all Bluetooth links but cannot provide guaranteed

quality over the WLAN links.

6.13.4 Algorithm 4: two-wire mechanism

Based on algorithm 2 and 3, the Host decides, on a case-by-case basis, whether WLAN or

Bluetooth is master.The Master role can be checked and changed at run-time by the Host

via an HCI command.

STLC2500D WLAN

BT_RF_NOT_ALLOWED

STLC2500D WLAN

WLAN_RF_NOT_ALLOWED

General specification STA2500D

40/58 Doc ID 16067 Rev 3

6.13.5 Algorithm 5: Alternating wireless medium access (AWMA)

AWMA utilizes a portion of the WLAN beacon interval for Bluetooth operations. From a

timing perspective, the medium assignment alternates between usage following WLAN

procedures and usage following Bluetooth procedures.

The timing synchronization between the WLAN and the STA2500D is done by the HW signal

MEDIUM_FREE.

Table 24. WLAN HW signal assignment

WLAN control

signal

(see also

Tab le 28 )

Scenario 1:

PTA

Scenario 2:

WLAN master

Scenario 3:

BT master Scenario 4:2-wire Scenario 5:

AWMA

WLAN 1 RF_CONFIRM BT_RF_NOT_

ALLOWED Not used BT_RF_NOT_

ALLOWED

MEDIUM_F

REE

WLAN 2 RF_REQUEST Not used WLAN_RF_NOT_

ALLOWED

WLAN_RF_NOT_

ALLOWED Not used

WLAN 3 STATUS Not used Not used Not used Not used

WLAN 4 FREQ

(optional) Not used Not used Not used Not used

STA2500D Digital interfaces

Doc ID 16067 Rev 3 41/58

7 Digital interfaces

7.1 The UART interface

The STA2500D contains a 4-pin (BT_UART_RXD, BT_UART_TXD, BT_UART_RTS, and

BT_UART_CTS) UART compatible with 16450, 16550 and 16750 standards. It is running up

to 4000 kbps (+1.5% / -1%).

The configuration is 8 data bits, 1 start bit, 1 stop bit, and no parity bit. The transmit and

receive paths contain a DMA function for low CPU load and high throughput. Auto RTS/CTS

is implemented in HW, controllable by SW.

The UART accepts all HCI commands as described in the Bluetooth specification, it

supports H4 proprietary commands and the Deep Sleep mode entry and wake-up through

H4 UART (see Section : Deep sleep mode entry and wake up through H4 UART). The

complete list of supported proprietary HCI commands is available upon request.

At startup, the UART baud rate is fixed at 115200 bps independently of the

BT_REF_CLK_IN frequency. A specific HCI command is provided to change the UART

baud rate when necessary within the range 9600 bps to 4000 kbps. All standard baud rates

and many other ones are supported.

7.2 The SPI interface

The physical SPI interface is made up of 5 signals: clock, chip select, data in, data out and

interrupt. When the SPI mode is selected, these signals are available through the

BT_UART/BT_SPI and BT_HOST_WAKEUP pins.

Figure 16. SPI interface

●SPI_CSN (on pin BT_UART_RTS/BT_SPI_CSN): chip select allows the use of multiple

Slaves (1 chip select per Slave). This signal is active low. This signal is mandatory,

even with only 1 Slave, because the Host must drive this signal to indicate SPI frames.

●SPI_CLK (on pin BT_UART_CTS/BT_SPI_CLK): clock signal, active for a multiple of

data length cycles during an SPI transfer (SPI_CSN active). The clock is allowed to be

active when SPI_CSN is not active, in order to serve other Slaves.

●SPI_DO (on pin BT_UART_TXD/BT_SPI_DO): data transfer from Slave to Master.

Data is generated on the negative edge of SPI_CLK by the Slave and sampled on the

Host BT Controller

SPI_CLK

SPI_CSN

SPI_DO

SPI_DI

SPI_INT

SPI_CLK

SPI_CSN

SPI_MISO

SPI_MOSI

SPI_INT

Digital interfaces STA2500D

42/58 Doc ID 16067 Rev 3

positive edge of SPI_CLK. When SPI_CSN is inactive, this BT Controller output is in

tristate mode.

●SPI_DI (on pin BT_UART_RXD/BT_SPI_DI): data transfer from Master to Slave. Data

is generated on the negative edge of SPI_CLK by the Master and sampled on the

positive edge of SPI_CLK.

●SPI_INT (on pin BT_HOST_WAKEUP/BT_SPI_INT): interrupt from the Slave, used to

request an SPI transfer by the Slave to the Master. The signal is active high (Host input

must be level sensitive).

The SPI interface is Master at the Host side, and Slave at Bluetooth Controller side. It is

designed to work with the H4 and enhanced H4 protocol. Also synchronous data packet

transfer (eSCO) over HCI is supported.

The SPI data length and endianness are configurable.

The SPI interface can only operate in half duplex mode.

Also the use of flow control is configurable. The flow control consists of an indication from

the Bluetooth Controller whether its receive buffers are ready to receive data. This indication

is available in three ways:

●On the SPI_DO during TSCS (time between SPI_CSN becoming active and SPI_CLK

becoming high), see FC in Figure 17 and Tscs in Figure 18

●In a register that can be read by the Host

●Optionally on one of the programmable GPIOs: GPIO_16. This is enabled by a SW

parameter download, see Section 7.5

The default SPI configuration is:

●Half duplex mode

●16 bit data length

●Most significant byte first

●Most significant bit first

●Flow control on SPI_DO and in a register

More detailed information on the SPI interface is available upon request.

Figure 17. SPI data transfer timing for data length of 8 bits and lsb first, full duplex

Z FCb0b1b2b3b4b5b6b7 Z

b0 b1 b2 b3 b4 b5 b6 b7

SPI_CSN

SPI_CLK

SPI_DO

SPI_DI

SPI_INT

STA2500D Digital interfaces

Doc ID 16067 Rev 3 43/58

Figure 18. SPI setup and hold timing

7.3 The PCM interface

The chip contains a 4-pin direct voice interface to connect to standard CODEC.

The interface supports multiport PCM operations for voice transfer. It can be programmed to

act as a Master or a Slave via a SW parameter download or via specific HCI commands.

The four signals of the multiport PCM interface are:

●PCM_CLK : PCM clock

●PCM_SYNC : PCM 8 kHz sync (every 125 s)

●PCM_A : PCM data (TX or RX)

●PCM_B : PCM data (RX or TX)

As a Master the interface by default generates a PCM clock rate of 2048 kHz, but it can be

configured to rates from 8 kHz up to 2048 kHz. As a Slave, it can automatically handle

external PCM clock rates from 128 kHz up to 4000 kHz. The default PCM_SYNC rate is 8

kHz.

The following external PCM data format are supported: linear (13 - 16 bit), µlaw (8 bit) or A-

law (8 bit).

Table 25. SPI timing parameters

Symbol Description Min. Typ. Max. Unit

PCL SPI_CLK full period 70 0 0 ns

TCLH High period of SPI_CLK 16.6 ns

TCLL Low period of SPI_CLK 26.4 ns

TCSH High period of SPI_CSN 1 * PCL ns

TCSL Low period of SPI_CSN 9 * PCL ns

TSCS Setup time, SPI_CSN Low to SPI_CLK high 1 * PCL ns

TSCL Setup time, SPI_CLK Low to SPI_CSN high 1/2 * PCL ns

TSDC Setup time, SPI_MOSI valid to SPI_CLK high 9.7 5 ns

THCD

Hold time, SPI_MOSI valid after SPI_CLK

high 0ns

TSCLD Setup time, SPI_CLK Low to SPI_MISO valid 26.5 ns

SPI_CSN

SPI_CLK

SPI_DI

SPI_DO

TCSL TCSH

TSCL

TCLL TCLH

TSCS

PCL

TSCLD

TSDC THCD

Digital interfaces STA2500D

44/58 Doc ID 16067 Rev 3

In Slave mode, all possible PCM_SYNC lengths are supported (including “short frame” (= 1

PCM_CLK period) and “long frame” (> 1 PCM_CLK period)). In Master mode, the length is

configurable (1 (“short frame”), 8 or 16 (“long frame”) PCM_CLK periods).

The start of the PCM data is configurable. One possible configuration is e.g. for a short

frame, the falling edge of the PCM_SYNC indicating the start of the PCM word. Another

possible configuration is e.g. for a long frame, the rising edge of the PCM_SYNC indicating

the start of the PCM word.

TX data are by default generated on the positive edge of PCM_CLK and expected to be

latched by the external device on the negative edge while RX data are latched on the

negative edge of PCM_CLK. But the inverted clock mode is also supported, whereby the

generation of TX data is on the negative edge and the latching of TX and RX data is on the

positive edge.

One additional PCM_SYNC signal can be provided via the GPIOs. See section 7.5 for more

details.

Figure 19. PCM (A-law, µ-law) standard mode

Figure 20. Linear mode

Figure 21. Multislot operation

The PCM implementation supports from 1 up to 3 slots per frame with the following

parameters:

D02TL558

PCM_CLK

PCM_SYNC

PCM_A B B

PCM_B

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

125µs

D02TL559

PCM_CLK

PCM_SYNC

PCM_A

PCM_B

0123456789101112131415

125μs

D02TL558

PCM_CLK

PCM_SYNC

PCM_A B B

PCM_B

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

125µs

STA2500D Digital interfaces

Doc ID 16067 Rev 3 45/58

Figure 22. PCM interface timing

Table 26. PCM interface parameters

Symbol Description Min. Typ. Max. Unit

PCM Interface

FPCM_CLK Frequency of PCM_CLK (Slave) 128(1) 2048 4000(2) kHz

FPCM_SYNC Frequency of PCM_SYNC - 8 - kHz

Psync_delay Delay of the starting of the first slot 0 - 255 cycles

SsSlot start (programmable for every slot) 0 - 255 cycles

D Data size 8 - 16 bits

N Number of slots per frame 1 - 3 -

1. Note that it is not possible to use 16 bits in Slave case if pcm_clk is 128kHz. This is the only exception.

2. In Master case, the maximum of PCM_CLK is 2048 kHz.

Table 27. PCM interface timing (at PCM_CLK = 2048 kHz)

Symbol Description Min. Typ. Max. Unit

tWCH High period of PCM_CLK 200 - - ns

tWCL Low period of PCM_CLK 200 - - ns

tWSH High period of PCM_SYNC 200 - - ns

tSSC Setup time, PCM_SYNC high to PCM_CLK low 100 - - ns

tSDC Setup time, PCM_A/B input valid to PCM_CLK low 100 - - ns

tHCD Hold time, PCM_CLK low to PCM_A/B input valid 100 - - ns

tDCD Delay time, PCM_CLK high to PCM_A/B output valid - - 150 ns

D02TL557

PCM_CLK

WCL

PCM_SYNC

PCM_A/B in

PCM_B/A out

MSB MSB-1 MSB-2 MSB-3 MSB-4

SSC

WCH

WSH

HCD

SDC

DCD

Digital interfaces STA2500D

46/58 Doc ID 16067 Rev 3

7.4 The JTAG interface

The JTAG interface is compliant with the JTAG IEEE Standard 1149.1. It allows both the

boundary scan of the digital pins and the debug of the ARM7TDMI application when

connected with the standard ARM7 developments tools. It is also used for the industrial test

of the device. The JTAG interface is available through the following 5 pins: BT_GPIO_8,

BT_GPIO_9, BT_GPIO_10, BT_GPIO_11 and BT_GPIO_16.

7.5 Alternate I/O functions

The STA2500D has 10 additional general purpose pins on top of the 4 PCM pins, the 4

UART pins and BT_CLK_REQ_OUT_1 that can also be reconfigured. They are fully

programmable via specific HCI commands. They can be configured as input, output,

interrupt with asynchronous or synchronous edge or level detection and/or wake-up.

The alternative functions are:

●Wake-up by the Host in Deep Sleep mode through UART or SPI with handshake (see

Section : Deep sleep mode entry and wake-up through H4 UART or H4 SPI with

handshake)

●WLAN coexistence control

●I2C interface

●PCM synchronization

●GPIOs

●UART / SPI interface

●external driver/LNA control for Class 1 operation.

19 pins can be redefined by SW to perform other functions. Pin BT_HOST_WAKEUP e.g.

can be redefined to perform up to 7 functions, depending on SW settings.

4 exemplary combinations of pin programmings are given in Ta bl e 2 8 . The available

functions are

●ex. 1: UART + I2C + Class 1 control

●ex. 2: UART + WLAN + Class 1 control

●ex. 3: SPI + WLAN + Class 1 control

●ex. 4: SPI + WLAN + I2C + Class 1 control

(The complete list of alternate functions is available upon request).

Table 28. Examples of BT_GPIO pin programming

STA2500D Pin Name ex. 1 ex. 2 ex. 3 ex. 4

BT_UART_RXD/BT_SPI_DI UART_RXD UART_RXD SPI_DI SPI_DI

BT_UART_TXD/BT_SPI_DO UART_TXD UART_TXD SPI_DO SPI_DO

BT_UART_CTS/BT_SPI_CLK UART_CTS UART_CTS SPI_CLK SPI_CLK

BT_UART_RTS/BT_SPI_CSN UART_RTS UART_RTS SPI_CS SPI_CS

BT_PCM_CLK PCM_CLK PCM_CLK PCM_CLK PCM_CLK

BT_PCM_SYNC PCM_SYNC PCM_SYNC PCM_SYNC PCM_SYNC

BT_PCM_A PCM_A PCM_A PCM_A PCM_A

STA2500D Digital interfaces

Doc ID 16067 Rev 3 47/58

7.6 The I2C interface

The I2C interface is used to access I2C peripherals.

The interface is a fast Master I2C; it has full control of the interface at all times. I2C Slave

functionality is not supported.

BT_PCM_B PCM_B PCM_B PCM_B PCM_B

BT_GPIO_0 I2C_CLK WLAN1 WLAN1 WLAN1

BT_CLK_REQ_IN_1 I2C_DAT WLAN2 WLAN2 I2C_DAT

BT_CLK_REQ_IN_2 GPIO_2 WLAN3 WLAN3 WLAN3

BT_HOST_WAKEUP/BT_SPI

_INT HOST_WAKEUP WLAN4 SPI_INT SPI_INT

BT_GPIO_11 ANT_SWITCH ANT_SWITCH ANT_SWITCH WLAN2

BT_GPIO_9 PA_LEVEL2 PA_LEVEL2 PA_LEVEL2 PA_LEVEL2

BT_GPIO_10 PA_LEVEL1 PA_LEVEL1 PA_LEVEL1 PA_LEVEL1

BT_GPIO_8 RX_ENABLE RX_ENABLE RX_ENABLE RX_ENABLE

BT_GPIO_16 PA_ENABLE PA_ENABLE PA_ENABLE PA_ENABLE

BT_CLK_REQ_OUT_1 CLK_REQ_OUT_1 CLK_REQ_OUT_1 CLK_REQ_OUT_1 CLK_REQ_OUT_1

BT_CLK_REQ_OUT_2 NA NA WLAN4 IC2_CLK

Table 28. Examples of BT_GPIO pin programming (continued)

STA2500D Pin Name ex. 1 ex. 2 ex. 3 ex. 4

HCI transport layer STA2500D

48/58 Doc ID 16067 Rev 3

8 HCI transport layer

The STA2500D supports the HCI transport layer as defined by the SIG: H4 []. It is supported

in combination with UART and SPI mode. The STA2500D also supports an enhanced

version of the H4 protocol in combination with SPI mode.

8.1 H4 UART transport layer

The objective of HCI UART transport layer is to make it possible to use Bluetooth HCI over a

serial interface between two UARTs on the same PCB. The HCI UART transport layer

assumes that the UART communication is free from line errors.

UART settings

The HCI UART transport layer uses the following settings for RS232:

●Baud rate :configurable (default baud rate 115200 bps)

●Number of data bits :8

●Parity bit :no parity

●Stop bit :1 stop bit

●Flow control :RTS/CTS

●Flow-off response time :500 µs

The flow-off response time defines the maximum time that the STA2500D can still receive

data after setting RTS high.

RTS/CTS flow control is used to prevent temporary UART buffer overrun between the

Bluetooth Controller and the Host.

The RS232 signals should be connected in a null-modem fashion, i.e. the Bluetooth

Controller TXD output should be connected to the Host RXD input and the Bluetooth

Controller RTS output should be connected to the Host CTS input and vice versa.

If the Bluetooth Controller RTS output (connected to the Host CTS input) is low, then the

Host is allowed to send.

If the Bluetooth Controller RTS output (connected to the Host CTS input) is high, then the

Host is not allowed to send.

If the Bluetooth Controller CTS input (connected to the Host RTS output) is low, then the

Bluetooth Controller is allowed to send.

If the Bluetooth Controller CTS input (connected to the Host RTS output) is high, then the

Bluetooth Controller is not allowed to send.

Figure 23. UART transport layer

BLUETOOTH

HOST

BLUETOOTH

HOST

CONTROLLER

BLUETOOTH HCI

HCI UART TRANSPORT LAYER

STA2500D HCI transport layer

Doc ID 16067 Rev 3 49/58

8.2 Enhanced H4 SPI transport layer

This is the default SPI mode.

The enhanced H4 protocol is based on the H4 protocol as defined by the SIG []. In addition

a messaging protocol is defined for controlling the Deep Sleep mode entry and wake-up,

see Section : Deep sleep mode entry and wake-up through enhanced H4 SPI.

Three messages are defined: SLEEP, WAKEUP and WOKEN. More details on the

messages are available upon request.

At SPI level, the default configuration is used:

●The SPI interface works in half duplex mode

●The data are exchanged in multiple of 16 bits

●The most significant byte first

●The most significant bit first

●There is a read and write command from the Host to access the Bluetooth device

●The Bluetooth device requests a transfer by the activation of the interrupt line

●Flow control on SPI_DO and in a register

8.3 H4 SPI transport layer

As stated in the previous section, the SPI interface is configurable. One possible

configuration is the following, implementing a simple H4 SPI transport layer.

●The SPI interface works in half duplex mode

●The data are exchanged in multiples of 8 bits

●The least significant bit first

●There is a read and write command from the Host to access the Bluetooth device

●The Bluetooth device requests a transfer by the activation of the interrupt line

●Flow control on BT_SPI_DO and in a register

8.4 eSCO over HCI

The STA2500D supports synchronous data packet transfer (eSCO) over HCI.

Package information STA2500D

50/58 Doc ID 16067 Rev 3

9 Package information

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®

specifications, grade definitions and product status are available at: www.st.com.

ECOPACK® is an ST trademark.

Figure 24. LFBGA48 (6x6x1.4mm) mechanical data and package dimensions

OUTLINE AND

MECHANICAL DATA

DIM.

mm inch

MIN. TYP. MAX. MIN. TYP. MAX.

A1.250 0.0492

A1 0.210 0.0083

A2 0.890 0.0350

A3 0.300 0.0118

A4 0.600 0.0236

b0.350 0.400 0.450 0.0138 0.0157 0.0177

D5.850 6.000 6.150 0.2303 0.2362 0.2421

D1 4.800 0.1890

E5.850 6.000 6.150 0.2303 0.2362 0.2421

E1 4.800 0.1890

e0.800 0.0315

F0.600 0.0236

ddd 0.100 0.0039

eee 0.150 0.0059

fff 0.080 0.0031

LFBGA48

Low profile Fine Pitch Ball Grid Array

8092328 B

Body: 6 x 6 x 1.4mm

STA2500D Package information

Doc ID 16067 Rev 3 51/58

Figure 25. Package markings

Note: The ECO level is reflected in the “Order code” (see Ta b l e 3 2 )

Table 29. Package markings legend

Item Description Format Value

A Type + version XXXXXX 2500D7

B Assembly Plant P -

C BE sequence (LL) LL -

D Assembly Year (Y) Y -

E Assembly Week (WW) WW -

F Second_lvl_intct - -

G Standard ST Logo - -

HDot (pin A1) - -

B D

References STA2500D

52/58 Doc ID 16067 Rev 3

10 References

Table 30. References

ID Short

name Name Date Owner

[1] - Specification of the Bluetooth System V2.1 + EDR (“Lisbon”) Not yet

released Bluetooth SIG

[2] - Specification of the Bluetooth System V2.0 + EDR November

2004 Bluetooth SIG

[3] - Specification of the Bluetooth System V1.2 November

2003 Bluetooth SIG

[4] -

Specification of the Bluetooth System - Host Controller

Interface [Transport Layer] Volume 04 Revision 1.2 or later,

2006, part A: UART v1.1

January

2006 Bluetooth SIG

[5] -

Radio Frequency Test Suite Structure (TSS) and Test

Purposes (TP) System Specification 1.2/2.0/2.0 + EDR,

document number RF.TS/2.0.E.3

March

2005 Bluetooth SIG

[6] -

IEEE 802.15.2, IEEE Recommended Practice for

Telecommunications and Information exchange between

systems – Local and metropolitan area networks Specific

Requirements - Part 15.2: Coexistence of Wireless Personal

Area Networks with Other Wireless Devices Operating in

Unlicensed Frequency Band

August

2003 IEEE

[7] WLAN

IEEE 802.11, IEEE Standards for Information Technology --

Telecommunications and Information Exchange between

Systems -- Local and Metropolitan Area Network -- Specific

Requirements -- Part 11: Wireless LAN Medium Access

Control (MAC) and Physical Layer (PHY) Specifications

1999 IEEE

[8] 802.11b

IEEE 802.11b, Supplement to 802.11-1999, Wireless LAN

MAC and PHY specifications: Higher speed Physical Layer

(PHY) extension in the 2.4 GHz band

1999 IEEE

[9] 802.11g

IEEE 802.11g, IEEE Standard for Information technology—

Telecommunications and information exchange between

systems—Local and metropolitan area networks—Specific

requirements—Part 11: Wireless LAN Medium Access

Control (MAC) and Physical Layer (PHY) specifications—

Amendment 4: Further Higher-Speed Physical Layer

Extension in the 2.4 GHz Band

2003 IEEE

[10] - STLC2500C_DS_Rev2.0.pdf, Datasheet of Bluetooth

2.0&EDR compliant single chip, Rev2.0 or later --

STA2500D Acronyms and abbreviations

Doc ID 16067 Rev 3 53/58

11 Acronyms and abbreviations

Table 31. Acronyms and abbreviations

Acronyms/

abbreviation Description

2-DH12-

DH32-DH5 Bluetooth 2 Mbps ACL packet types

2-EV3

2-EV5 Bluetooth 2 Mbps synchronous packet types

3-DH1

3-DH3

3-DH5

Bluetooth 3 Mbps ACL packet types

3-EV3

3-EV5 Bluetooth 3 Mbps synchronous packet types

8-DPSK 8 phase Differential Phase Shift Keying

A/D Analog to Digital

AC Alternating Current

ACL Asynchronous Connection Oriented

AHB Advanced High-performance Bus

A-law Audio encoding standard

AMBA Advanced Micro-controller Bus Architecture

AMR Absolute Maximum Rating

APB Advanced Peripheral Bus

ARM7 Micro-processor

ARM7TDMI Micro-processor

AWMA Alternating Wireless Medium Access

BB Base Band

BER Bit Error Rate

BOM Bill Of Materials

BR Basic Rate

BT Bluetooth

BW Band Width

C/I Carrier-to-co-channel Interference

CMOS Complementary Metal Oxide Semiconductor

CODEC COder DEcoder

CPU Central Processing Unit

CQDDR Channel Quality Driven Data Rate change

CVSD Continuous Variable Slope Delta modulation

DC Direct Current

Acronyms and abbreviations STA2500D

54/58 Doc ID 16067 Rev 3

DEVM Differential Error Vector Amplitude

DH1

DH3

DH5

Bluetooth 1 Mbps ACL packet types

DM1

DM3

DM5

Bluetooth 1 Mbps ACL packet types

DMA Direct Memory Access

DV Bluetooth 1 Mbps synchronous packet type

EBC Ericsson technology licensing Baseband Core

EDR Enhanced Data Rate

EIR Extended Inquiry Response

EPR Encryption Pause/Resume

eSCO extended SCO

EV3

EV4

EV5

Bluetooth 1 Mbps synchronous packet types

FHS Frequency Hopping Synchronization

GFSK Gaussian Frequency Shift Keying

GPIO General Purpose I/O pin

GSM Global System for Mobile communications

H4 UART based HCI transport

HCI Host Controller Interface

HV1

HV3 Bluetooth 1 Mbps synchronous packet types

HW HardWare

I/O Input/Output

I2C Inter-Integrated Circuit

IF Intermediate Frequency

ISM Industrial, Scientific and Medical

JTAG Joint Test Action Group

L2CAP Logical Link Control and Adaptation Protocol

LMP Link Manager Protocol

LNA Low Noise Amplifier

LO Local Oscillator

LSTO Link Supervision Time Out

-law Audio encoding standard

Table 31. Acronyms and abbreviations (continued)

Acronyms/

abbreviation Description

STA2500D Acronyms and abbreviations

Doc ID 16067 Rev 3 55/58

/4-DQPSK /4 rotated Differential Quaternary Phase Shift Keying

PA Power Amplifier

PCB Printed Circuit Board

PCM Pulse Code Modulation

PD Pull-Down

PLL Phase Locked Loop

PPEC Pitch-Period Error Concealment

PTA Packet Traffic Arbitration

PU Pull-Up

QoS Quality of Service

RAM Random Access Memory

RC Resistance-Capacitance

RF Radio Frequency

rms root mean squared

ROM Read Only Memory

RS232 ANSI/EIA/TIA-232-F, September 1997, Interface Between Data Terminal Equipment

and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange

RSSI Receive Signal Strength Indication

RX Receive

SCO Synchronous Connection Oriented

SIG Bluetooth Special Interest Group

SPI Serial Peripheral Interface

ST STMicroelectronics

SW SoftWare

TBD To Be Defined

TeSCO eSCO interval

TSCO SCO interval

Tsniff Sniff interval

TX Transmit

UART Universal Asynchronous Receiver/Transmitter

VCO Voltage Controlled Oscillator

VGA Variable Gain Amplifier

WCDMA Wideband Code Division Multiple Access

WFBGA Very Very Thin Profile Fine Pitch Ball Grid Array

WLAN Wireless Local Area Network

WLCSP Wafer-Level Chip Scale Package

Table 31. Acronyms and abbreviations (continued)

Acronyms/

abbreviation Description

Order codes STA2500D

56/58 Doc ID 16067 Rev 3

12 Order codes

Table 32. Ordering information

Order code Package Packing Production

STA2500DC LFBGA48 Tray Simplified production flow

STA2500DCTR LFBGA48 Tape and reel Simplified production flow

STA2500D LFBGA48 Tray Automotive version

STA2500DTR LFBGA48 Tape and reel Automotive version

STA2500D Revision history

Doc ID 16067 Rev 3 57/58

13 Revision history

Table 33. Document revision history

Date Revision Changes

24-Jul-2009 1 Initial release.

18-Jan-2010 2 Removed device summary table in cover page.

Added Section 12: Order codes on page 56.

17-Sep-2013 3 Updated Disclaimer

STA2500D

58/58 Doc ID 16067 Rev 3

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the

right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any

time, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are so lel y res ponsibl e fo r the c hoic e, se lecti on an d use o f the S T prod ucts and s ervic es des crib ed he rein , and ST assumes n o

liability whatsoever relating to the choice, select ion or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this

document ref er s to an y t hird pa rty p ro duc ts or se rv ic es it sh all n ot be deem ed a li ce ns e gran t by ST fo r the use of su ch t hir d party products

or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such

third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIM S ANY EXPRESS OR IMPLIED

WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMIT ATION IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS

OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PAT ENT, COPYRIGHT OR OTHER INTELLECTUAL PRO PERTY RIGHT.

ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE

SUPPORTING, ACTIVE IMPL ANTED DEVICES OR SYSTEMS WITH PRODU CT FUNCTIONAL SAFETY REQUIREME NTS; (B)

AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS

OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT

PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS

EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY

DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE

DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void

any warrant y granted by ST for the S T product or se rvice descr ibed herein a nd shall no t create or e xtend in any manner whatsoe ver, any

liability of ST.

ST and the ST lo go are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replace s all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

STMicroele ctr on ic s gr oup of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Ger m any - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America

www.st.com

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

STMicroelectronics:

STA2500DC STA2500DCTR STA2500DTR STA2500D