AZ696 10 AMP SUBMINIATURE POWER RELAY FEATURES * Miniature size: Form A version: 0.63" (16mm) height, 1.10" (30mm) length, 0.39" (10mm) width * High sensitivity, 100mW pickup * Dielectric strength 4000Vrms * Isolation spacing greater than 8mm * Approvals/Standards include: UL, VDE, IEC * 10 Amp switching capability * Epoxy sealed for automatic wave soldering and cleaning * UL, CUR file E43203 * VDE file 40012571 CONTACTS Arrangement Ratings GENERAL DATA SPDT (1 Form C) SPST (1 Form A) SPST (1 Form B) Resistive load: Max. switched power: 300W or 2500VA Max. switched current: 10A Max. switched voltage: 240VDC* or 440VAC Life Expectancy Mechanical Electrical Minimum operations 10 million 1 X 105 at 8A, 240VAC Res. Operate Time (typical) 10ms at nominal coil voltage Release Time (typical) 5ms at nominal coil voltage (with no coil suppression) *Note: If switching voltage is greater than 30VDC, special precautions must be taken. Please contact the factory. Rated Load UL VDE 10A at 30VDC Resistive 10A at 250VAC General use 1/4 HP at 120VAC 1/2 HP at 250VAC B300 Pilot duty Insulation Resistance 1000 megohms min. at 20C, 500VDC, 50% RH Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40C (-40F) to 85C (185F) -40C (-40F) to 110C (230F) 1 Form C (unsealed) 10 A at 250VAC, resistive, 85C, 50k cycles [2] 8 A at 250VAC, resistive, 40C, 50k cycles [1] 4 A at 250VAC, cos phi 0.9, 70C, 50k cycles [1] Vibration 0.062" (1.5mm) DA at 10-55Hz Shock 20g Enclosure P.B.T. polyester 1 Form A / 1 Form B / 1 Form C (sealed) 10 A at 250VAC, resistive, 85C, 10k cycles [2] Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270C (518F) Max. Solder Time 5 seconds Max. Solvent Temp. 80C (176F) Max. Immersion Time 30 seconds Weight 11 grams 1 Form A / 1 Form B (unsealed) 10 A at 250VAC, resistive, 85C, 50k cycles [2] 8 A at 250VAC, resistive, 40C, 100k cycles [1] 5 A at 250VAC, cos phi 0.9, 70C, 50k cycles [1] Material Silver cadmium oxide [1]; silver tin oxide [2] Resistance < 30 milliohms initially (at 6V, 1A voltage drop method) COIL Power At Pickup Voltage (typical) 110mW Max. Continuous Dissipation 1.5W at 20C (68F) ambient 1.2W at 40C (104F) ambient 20C (36F) at nominal coil voltage Temperature Rise Temperature Dielectric Strength 4000Vrms coil to contact (at sea level for 1 min.) 1000Vrms between open contacts Max. 110C (230F) NOTES 1. All values at 20C (68F). 2. Relay may pull in with less than "Must Operate" value. 3. Specifications subject to change without notice. 4. It's recommended to remove vent nipple on sealed versions to expand life expectancy when switching higher loads. 5/20/16 AZ696 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 Must Operate VDC 3.5 ORDER NUMBER Max Continuous VDC 12.0 Coil Resistance Ohms 10% 110 1 Form A (SPST-NO) AZ696-1A-5D 1 Form C (SPDT) AZ696-1C-5D AZ696-1C-6D 6 4.2 14.5 160 AZ696-1A-6D 9 6.3 22.0 360 AZ696-1A-9D AZ696-1C-9D 12 8.4 29.5 660 AZ696-1A-12D AZ696-1C-12D 18 12.6 44.0 1,500 AZ696-1A-18D AZ696-1C-18D 24 16.8 54.0 2,200 AZ696-1A-24D AZ696-1C-24D 48 33.6 102.0 8,000 AZ696-1A-48D AZ696-1C-48D * Substitute "1B" in place of "1A" for 1 Form B contact. ADD suffix "E" to "1A" or "1B" or "1C" for silver tin oxide contacts. Add Suffix "E" at the end of order number for sealed version. When suffix "E" is specified for Epoxy Seal, refer to AZ INTERNATIONAL APPROVALS "Relay Technical Notes" on AZ website - Product Resources. Consult factory for other PCB process conditions that may apply. VDE 0435/09.72 at 8 Amps VDE 0631/12.83 at 8 Amps VDE 0700/1/2.81 at 8 Amps Germany MECHANICAL DATA Coil Temperature Rise 1 FORM C 1 FORM A and 1 FORM B 100 90 1.10 (28) .394 (10) .394 (10) .618 (15.7) .618 (15.7) FORM C .638 (16.2) .638 (16.2) .138 (3.5) .138 (3.5) .024 x .035 (0.6 x 0.9) .024 x .035 (0.6 x 0.9) .024 x .039 (0.6 x 1) Coil Temperature Rise C 80 1.18 (30) .024 x .039 (0.6 x 1) 70 10 A 60 50 0A 40 30 20 10 0 60 80 100 120 140 160 180 200 220 Percent of Nominal Coil Voltage at 20C WIRING DIAGRAMS PC BOARD LAYOUT 1 FORM C 1 2 x o .051 (o 1.3) 1 FORM C Maximum Switching Capacity 4 10.0 .299 (7.6.) .748 (19.) .122 (3.1) 3 x o .059 (o 1.5) .126 (3.2) .126 (3.2) 2 3 9.0 8.0 7.0 6.0 5.0 5 DC Resistive Load 4.0 1 FORM A 1 3.0 3 AC Resistive Load 1 FORM A and 1 FORM B 2 x o .051 (o 1.3) 2 4 1 1.0 .9 .8 .7 .6 .5 .4 1 FORM B .299 (7.6.) CURRENT 2.0 .3 3 Viewed toward terminals Viewed toward terminals 1000 400 500 600 700 800 900 300 200 50 60 70 80 90 100 4 40 .1 2 30 .197 (5) 10 .122 (3.1) 20 .2 2 x o .059 (o 1.5) .748 (19) VOLTAGE Dimensions in inches with metric equivalents in parentheses. Tolerance: .010" 5/20/16