06035C103KAT2A - AVX Corporation - Datasheet.Directory

X7R Dielectric

General Specifications

X7R formulations are called “temperature stable” ceramics

and fall into EIA Class II materials. X7R is the most popular of

these intermediate dielectric constant materials. Its tempera-

ture variation of capacitance is within ±15% from

-55°C to +125°C. This capacitance change is non-linear.

Capacitance for X7R varies under the influence of electrical

operating conditions such as voltage and frequency.

X7R dielectric chip usage covers the broad spectrum of

industrial applications where known changes in

capacitance due to applied voltages are acceptable.

PART NUMBER (see page 2 for complete part number explanation)

% Cap Change

-60 -40 -20 0 20 40 60 80 100 120 140

Temperature °C

X7R Dielectric

Typical Temperature Coefficient

-5

-10

-15

-20

-25

% ⌬ Capacitance

+10

+20

+30

-10

-20

-30

1KHz 10 KHz 100 KHz 1 MHz 10 MHz

Frequency

⌬ Capacitance vs. Frequency

Insulation Resistance (Ohm-Farads)

1,000

10,000

100

0020 120

40 60 80

Temperature °C

Insulation Resistance vs Temperature

100

Impedance, ⍀

10 100 1000

Frequency, MHz

Variation of Impedance with Cap Value

Impedance vs. Frequency

1,000 pF vs. 10,000 pF - X7R

0805

0.10

0.01

1.00

1,000 pF

10,000 pF

10.00

Impedance, ⍀

110

100 1,000

Frequency, MHz

Variation of Impedance with Chip Size

Impedance vs. Frequency

100,000 pF - X7R

0.1

.01

1.0

1206

0805

1210

Impedance, ⍀

110

100 1,000

Frequency, MHz

Variation of Impedance with Chip Size

Impedance vs. Frequency

10,000 pF - X7R

0.1

.01

1.0

1206

0805

1210

0805

Size

(L" x W")

Voltage

4V = 4

6.3V = 6

10V = Z

16V = Y

25V = 3

50V = 5

100V = 1

200V = 2

500V = 7

Dielectric

X7R = C

103

Capacitance

Code (In pF)

2 Sig. Digits +

Number of Zeros

Capacitance

Tolerance

J = ± 5%*

K = ±10%

M = ± 20%

*≤1μF only

Packaging

2 = 7" Reel

4 = 13" Reel

7 = Bulk Cass.

9 = Bulk

Contact

Factory For

Multiples

Special

Code

A = Std. Product

Terminations

T = Plated Ni

and Sn

7 = Gold Plated*

Z= FLEXITERM®**

Failure

Rate

A = Not

Applicable

*Optional termination

**See FLEXITERM®

X7R section

NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers.

Contact factory for non-specified capacitance values.

X7R Dielectric

Specifications and Test Methods

Parameter/Test X7R Specification Limits Measuring Conditions

Operating Temperature Range -55ºC to +125ºC Temperature Cycle Chamber

Capacitance Within specified tolerance

≤ 2.5% for ≥ 50V DC rating Freq.: 1.0 kHz ± 10%

Dissipation Factor ≤ 3.0% for 25V DC rating Voltage: 1.0Vrms ± .2V

≤ 3.5% for 16V DC rating For Cap > 10 μF, 0.5Vrms @ 120Hz

≤ 5.0% for ≤ 10V DC rating

Insulation Resistance 100,000MΩ or 1000MΩ - μF, Charge device with rated voltage for

whichever is less 120 ± 5 secs @ room temp/humidity

Charge device with 300% of rated voltage for

Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current

limited to 50 mA (max)

Note: Charge device with 150% of rated

voltage for 500V devices.

Appearance No defects Deflection: 2mm

Capacitance Test Time: 30 seconds

Resistance to Variation ≤ ±12%

Flexure Dissipation Meets Initial Values (As Above)

Stresses Factor

Insulation ≥ Initial Value x 0.3

Resistance

Solderability ≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC

with fresh solder for 5.0 ± 0.5 seconds

Appearance No defects, <25% leaching of either end terminal

Capacitance

Variation ≤ ±7.5%

Dip device in eutectic solder at 260ºC for 60

Dissipation Meets Initial Values (As Above) seconds. Store at room temperature for 24 ± 2

Resistance to Factor hours before measuring electrical properties.

Solder Heat Insulation Meets Initial Values (As Above)

Resistance

Dielectric Meets Initial Values (As Above)

Strength

Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes

Capacitance

Variation ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes

Dissipation Meets Initial Values (As Above) Step 3: +125ºC ± 2º 30 ± 3 minutes

Thermal Factor

Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes

Resistance

Dielectric Meets Initial Values (As Above) Repeat for 5 cycles and measure after

Strength 24 ± 2 hours at room temperature

Appearance No visual defects

Capacitance

Variation ≤ ±12.5%

Dissipation ≤ Initial Value x 2.0 (See Above)

Load Life Factor

Insulation ≥ Initial Value x 0.3 (See Above)

Resistance

Dielectric Meets Initial Values (As Above)

Strength

Appearance No visual defects

Capacitance

Variation ≤ ±12.5%

Load Dissipation ≤ Initial Value x 2.0 (See Above)

Humidity Factor

Insulation ≥ Initial Value x 0.3 (See Above)

Resistance

Dielectric Meets Initial Values (As Above)

Strength

Charge device with 1.5 rated voltage (≤ 10V) in

test chamber set at 125ºC ± 2ºC

for 1000 hours (+48, -0)

Remove from test chamber and stabilize

at room temperature for 24 ± 2 hours

before measuring.

Store in a test chamber set at 85ºC ± 2ºC/

85% ± 5% relative humidity for 1000 hours

(+48, -0) with rated voltage applied.

Remove from chamber and stabilize at

room temperature and humidity for

24 ± 2 hours before measuring.

1mm/sec

90 mm

X7R Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

SIZE 0201 0402 0603 0805 1206

Soldering Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave

Packaging All Paper All Paper All Paper Paper/Embossed Paper/Embossed

(L) Length mm 0.60 ± 0.03 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20

(in.) (0.024 ± 0.001) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008)

(W) Width mm 0.30 ± 0.03 0.50 ± 0.10 0.81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20

(in.) (0.011 ± 0.001) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008)

(t) Terminal mm 0.15 ± 0.05 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25

(in.) (0.006 ± 0.002) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010)

WVDC 10 16 25 16 25 50 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 500

Cap 100 A A A

(pF) 150 A A A

220 A A A C

330 AAA C GGG JJJJJJ K

470 AA C GGG JJJJJJ K

680 AA C GGG JJJJJJ K

1000 A A C G G G JJJJJJ K

1500 A C G G JJJJJJ JJJJJJM

2200 A C G G JJJJJJ JJJJJJM

3300 A C C G G JJJJJJ JJJJJJM

4700 A C C G G JJJJJJ JJJJJJM

6800 A C C G G JJJJJJ JJJJJJP

Cap 0.010 A C C G G JJJJJJ JJJJJJP

(μF 0.015 C G G JJJJJJ JJJJJM

0.022 C G G JJJJJN JJJJJM

0.033 G G JJJJN JJJJJM

0.047 G G G JJJJN JJJJJM

0.068 G G G JJJJN JJJJJP

0.10 C GGGG JJJJN JJJJMP

0.15 G G J J J N N JJJJQ

0.22 G G J* J J N N N JJJJQ

0.33 NNNNN J JMPQ

0.47 J* NNNNN MMMPQ

0.68 NNN MMQQQ

1.0 J* J* N N N M M Q Q Q

1.5 PQQ

2.2 J* P* Q Q Q

3.3

4.7 P* P* Q* Q* Q*

10 P* Q* Q*

22 Q*

100

WVDC 10 16 25 16 25 50 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 6.3 10 16 25 50 100 200 500

SIZE 0201 0402 0603 0805 1206

Letter ACEGJKMNPQXYZ

Max. 0.33 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79

Thickness (0.013) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110)

PAPER EMBOSSED

*Optional Specifications – Contact factory

X7R Dielectric

Capacitance Range

Letter ACEGJKMNPQXYZ

Max. 0.33 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79

Thickness (0.013) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110)

PAPER EMBOSSED

PREFERRED SIZES ARE SHADED

SIZE 1210 1812 1825 2220 2225

Soldering Reflow Only Reflow Only Reflow Only Reflow Only Reflow Only

Packaging Paper/Embossed All Embossed All Embossed All Embossed All Embossed

(L) Length mm 3.20 ± 0.20 4.50 ± 0.30 4.50 ± 0.30 5.70 ± 0.40 5.72 ± 0.25

(in.) (0.126 ± 0.008) (0.177 ± 0.012) (0.177 ± 0.012) (0.225 ± 0.016) (0.225 ± 0.010)

(W) Width mm 2.50 ± 0.20 3.20 ± 0.20 6.40 ± 0.40 5.00 ± 0.40 6.35 ± 0.25

(in.) (0.098 ± 0.008) (0.126 ± 0.008) (0.252 ± 0.016) (0.197 ± 0.016) (0.250 ± 0.010)

(t) Terminal mm 0.50 ± 0.25 0.61 ± 0.36 0.61 ± 0.36 0.64 ± 0.39 0.64 ± 0.39

(in.) (0.020 ± 0.010) (0.024 ± 0.014) (0.024 ± 0.014) (0.025 ± 0.015) (0.025 ± 0.015)

WVDC 10 16 25 50 100 200 500 50 100 200 500 50 100 25 50 100 200 50 100

Cap 100

(pF) 150

220

330

470

680

1000

1500 JJJJJJM

2200 JJJJJJM

3300 JJJJJJM

4700 JJJJJJM

6800 JJJJJJM

Cap 0.010 JJJJJJMKKKKMM XXXMP

(μF 0.015 JJJJJJPKKKPMM XXXMP

0.022 JJJJJJQKKKPMM XXXMP

0.033 JJJJJJQKKKXMM XXXMP

0.047 JJJJJJ KKKZMM XXXMP

0.068 JJJJJM KKKZMM XXXMP

0.10 JJJJJM KKKZMM XXXMP

0.15 JJJJMZ KKP MM XXXMP

0.22 JJJJPZ KKP MM XXXMP

0.33 JJJJQ KMX MM XXXMP

0.47 MMMMQ K P MM X X XM P

0.68 M M P X X M Q M P X X M P

1.0NNPXZMXMPXXMP

1.5NNZZZ ZZ M XX MX

2.2XXZZZ ZZ XX M

3.3XXZZ Z XZ

4.7XXZZ Z XZ

10 Z Z Z* Z

22 Z* Z* Z

100

WVDC 10 16 25 50 100 200 500 50 100 200 500 50 100 25 50 100 200 50 100

SIZE 1210 1812 1825 2220 2225

䉲

*Optional Specifications – Contact factory