Multiple Input Programmable Supervisory ICs ADM6305/ADM6306 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAMS VCC RST IN1 RESET GENERATOR RESET 0.4V/1.23V RST IN2 ADM6305 0.4V/1.23V GND 09345-001 Adjustable input threshold voltage options: 0.4 V and 1.23 V Pretrimmed VCC threshold options (ADM6306) Increments between 2.5 V and 5 V Manual reset input (ADM6306) 4 factory programmed reset timeout delays 1 ms, 20 ms, 140 ms, and 1.12 sec (minimum) Reset output stage: active low, open drain Low power consumption: 5 A typical Power supply glitch immunity 5-lead SOT-23 package Temperature range: -40C to +125C Figure 1. VCC APPLICATIONS Portable/battery operated equipment Microprocessor systems Multivoltage applications 1.23V RST IN RESET GENERATOR RESET 0.4V/1.23V VCC GLITCH REJECTION GND 09345-002 ADM6306 MR Figure 2. GENERAL DESCRIPTION The ADM6305/ADM6306 are dual voltage supervisors designed to monitor two supplies and provide a reset signal to DSP- and microprocessor-based systems. Low supply current and a small form factor make these devices suitable for portable and battery operated applications. If a monitored power supply voltage falls below the minimum voltage threshold, a single active low output asserts triggering a system reset. After all voltages rise above the selected threshold level, the reset signal remains low for the reset timeout period. Four reset timeout options are available. The ADM6305 monitors two supplies via two adjustable resistor-programmable undervoltage reset inputs. Both RST IN1 and RST IN2 have a reset threshold of either 0.4 V or 1.23 V depending on the particular model; that is, the RST IN1 and RST IN2 threshold of the ADM6305D3ARJZ-RL7 model is Rev. C 1.23 V, while in the case of ADM6305D3ARJZ1-RL7 model, it is 0.4 V. The VCC input of the ADM6305 is not a monitored input. The ADM6306 has one adjustable undervoltage reset input, RST IN, which features a choice of reset threshold, 0.4 V or 1.23 V (see the Ordering Guide for more information). The ADM6306 incorporates a variety of internally pretrimmed VCC undervoltage threshold options for monitoring supply voltages in increments between 2.5 V and 5 V. The ADM6306 also includes a manual reset input. Not all options are released for sale as standard models. See the Ordering Guide for details. The ADM6305/ADM6306 RESET output remains valid as long as VCC exceeds 0.9 V. The ADM6305/ADM6306 are available in a 5-lead SOT-23 package. These devices are specified over the temperature range of -40C to +125C. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2010-2018 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADM6384 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Typical Performance Characteristics ..............................................7 Applications ....................................................................................... 1 Circuit Description............................................................................9 Functional Block Diagrams ............................................................. 1 Reset Output ..................................................................................9 General Description ......................................................................... 1 Manual Reset Input .......................................................................9 Revision History ............................................................................... 2 Applications Information .............................................................. 10 Specifications..................................................................................... 3 Negative Going VCC Transients................................................. 10 Absolute Maximum Ratings............................................................ 5 Ensuring Reset Valid to VCC = 0 V ........................................... 10 ESD Caution .................................................................................. 5 Outline Dimensions ....................................................................... 11 Pin Configuration and Function Descriptions ............................. 6 Ordering Guide .......................................................................... 11 REVISION HISTORY 4/2018--Rev. D to Rev. E Changes to General Description Section ...................................... 1 Added Note 2, Table 1; Renumbered Sequentially ....................... 3 Changes to Ordering Guide .......................................................... 11 6/2016--Rev. C to Rev. D Change to Table 3 ............................................................................. 6 Updated Outline Dimensions ....................................................... 11 4/2011--Rev. B to Rev. C Updated Outline Dimensions ....................................................... 11 Changes to Ordering Guide .......................................................... 11 7/2008--Rev. A to Rev. B Changes to Figure 5, Figure 8, and Figure 9.................................. 7 Changes to Figure 10 ........................................................................ 8 Changes to Figure 15 ...................................................................... 11 Changes to Ordering Guide .......................................................... 11 1/2007--Rev. 0 to Rev. A Updated Format .................................................................. Universal Changes to Specifications Table ...................................................... 3 Updated Outline Dimensions ....................................................... 11 Changes to Ordering Guide .......................................................... 11 7/2005--Revision 0: Initial Version Rev. E | Page 2 of 12 Data Sheet ADM6305/ADM6306 SPECIFICATIONS VCC = 2.5 V to 5 V for the ADM6305, VCC = (VTH + 2.5%) to 5.5 V for the ADM6306. TA = -40C to +125C, unless otherwise noted. Typical values are at TA = 25C. Table 1. Parameter OPERATING VOLTAGE RANGE, VCC 1 Min 0.9 0.9 Typ Max 5.5 VTH - 1% VTH - 1.5% VTH - 2.5% 5 5 VTH VTH VTH 25 2 x VTH 16 20 VTH + 1% VTH + 1.5% VTH + 2.5% 1.0 20 140 1120 1.4 28 200 1570 2.0 40 280 2240 0.4 0.3 0.3 0.3 0.3 ms ms ms ms V V V V V 0.8 0.3 x VCC V V V V s s s ns k VTH > 4.0 V VTH < 4.0 V VTH > 4.0 V VTH < 4.0 V TA = 0C to +70C TA = -40C to +125C V TA = 25C TA = -40C to +85C TA = -40C to +125C 0 V < VRST IN < VCC - 0.3 V 4, TA = -40C to +85C VRST IN = VRSTH INPUT CURRENT, ICC VCC THRESHOLD VOLTAGE (ADM6306) 2, 3 RESET THRESHOLD TEMPERATURE COEFFICIENT RESET THRESHOLD HYSTERESIS (VHYST) RESET TIMEOUT PERIOD (tRP)3 ADM630xD1 ADM630xD2 ADM630xD3 ADM630xD4 RESET OUTPUT VOLTAGE (VOL) MR INPUT (ADM6306) VIL VIH MR Minimum Input Pulse Width MR Glitch Rejection MR To Reset Delay MR Pull-Up Resistance 1.23 V ADJUSTABLE RESET COMPARATOR INPUT RST INx Input Threshold, VRSTH RST INx Input Current, IRST INx RST INx Hysteresis 0.4 V ADJUSTABLE RESET COMPARATOR INPUT RST INx Input Threshold, VRSTH RST INx Input Current, IRST INx 2.4 0.7 x VCC 1 1.5 32 1.22 1.211 1.20 -25 -25 0.1 500 63.5 1.23 1.23 100 1.24 1.249 1.26 +25 +25 2.5 0.396 0.394 0.39 -25 -25 0.40 0.40 0.40 0.404 0.406 0.41 +25 +25 Unit V V A A V V V ppm/C mV V nA nA mV V V V nA nA Test Conditions/Comments VCC that guarantees valid output VCC = 5.5 V, TA = -40C to +85C VCC = 5.5 V, TA = -40C to +125C TA = 25C TA = -40C to +85C TA = -40C to +125C VCC > 4.25 V, ISINK = 3.2 mA VCC > 2.5 V, ISINK = 1.2 mA VCC > 1.2 V, ISINK = 500 A VCC > 1 V, ISINK = 50 A VCC > 0.9 V, ISINK = 25 A TA = 25C TA = -40C to +85C TA = -40C to +125C 0 V < VRST INx < VCC - 0.3 V4, TA = -40C to +85C VRST IN = VRSTH The ADM6305 switches from undervoltage reset to normal operation when 1.5 V > VCC < 2.5 V. The AMD6306 monitors VCC through an internal factory trimmed voltage divider, which programs the nominal reset threshold. Factory-trimmed reset thresholds are available in approximately 100 mV increments from 2.5 V to 5 V. 3 Not all options are released for sale as standard models. See the Ordering Guide for details. 4 Guaranteed by design. 1 2 Rev. C | Page 3 of 12 ADM6305/ADM6306 Data Sheet ABSOLUTE MAXIMUM RATINGS THERMAL RESISTANCE Table 2. Parameter VCC All Pins (Except VCC) Input/Output Current Rate of Rise, VCC Storage Temperature Range Operating Temperature Range Lead Temperature (10 sec) Junction Temperature Rating -0.3 V to +6 V -0.3 V to (VCC + 0.3 V) 20 mA 100 V/s -65C to +160C -40C to +125C 300C 150C Table 3. Package Type 5-Lead SOT-23 ESD CAUTION Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. C | Page 4 of 12 JA 240 Unit C/W Data Sheet ADM6305/ADM6306 RESET 1 5 VCC 4 RST IN2 ADM6305 GND 2 TOP VIEW (Not to Scale) RST IN1 3 09345-003 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 3. ADM6305 Pin Configuration Table 4. ADM6305 Pin Function Descriptions Mnemonic RESET GND RST IN1 4 RST IN2 5 VCC Description Active Low, Open-Drain RESET Output. Ground. Adjustable Reset Comparator Input. This pin asserts RESET if the input voltage is below threshold. Its high input impedance allows the use of an external resistor divider to program the monitoring threshold. Connect this pin to the VCC pin if it is not used. Adjustable Reset Comparator Input. This pin asserts RESET if the input voltage is below threshold. Its high input impedance allows the use of an external resistor divider to program the monitoring threshold. Connect this pin to VCC if it is not used. Power Supply Input. VCC is not monitored on the ADM6305. RESET 1 5 VCC 4 RST IN ADM6306 GND 2 MR 3 TOP VIEW (Not to Scale) 09345-004 Pin No. 1 2 3 Figure 4. ADM6306 Pin Configuration Table 5. ADM6306 Pin Function Descriptions Pin No. 1 2 3 4 Mnemonic RESET GND MR RST IN 5 VCC Description Active Low, Open-Drain RESET Output. Ground. Manual Reset Input. Adjustable Reset Comparator Input. This pin asserts RESET if the input voltage is below threshold. Its high input impedance allows the use of an external resistor divider to program the monitoring threshold. Connect this pin to the VCC pin if it is not used. Power Supply Input. VCC is monitored on the ADM6306. Rev. C | Page 5 of 12 ADM6305/ADM6306 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 6.0 90 80 1mV/1s PROPAGATION DELAY (s) SUPPLY CURRENT (A) 5.5 VCC = 4.5V 5.0 VCC = 5.5V 4.5 VCC = 2.5V 4.0 VCC = 3.5V 70 60 10mV/1s 50 40 30 20 3.5 -40 -20 0 20 40 60 80 100 120 125 TEMPERATURE (C) 0 09345-005 3.0 -40 20 40 60 80 100 120 125 Figure 8. VCC Falling Propagation Delay vs. Temperature 1.10 10k TRANSIENT DURATION (s) 1.05 1.00 0.95 1k 100 TRANSIENT DURATION (s) VTH = 5V TRANSIENT DURATION (s) VTH = 2.5V 10 0.85 -40 -20 0 20 40 60 80 100 120 125 TEMPERATURE (C) 1 Figure 6. Reset Timeout vs. Temperature 0 400 800 1200 OVERDRIVE, VTH - VCC (mV) 09345-009 0.90 09345-006 Figure 9. Maximum Transient Duration vs. VCC Reset Threshold Overdrive 1.010 120 1.008 100 PROPAGATION DELAY (s) 1.006 1.004 1.002 1.000 0.998 0.996 0.994 1mV/1s 80 60 10mV/1s 40 20 0.992 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) Figure 7. Reset Threshold vs. Temperature 120 125 0 09345-007 0.990 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 125 09345-010 NORMALIZED RESET TIMEOUT 0 TEMPERATURE (C) Figure 5. Supply Current vs. Temperature NORMALIZED RESET THRESHOLD (V/V) -20 09345-008 10 Figure 10. RST IN (VTH = 1.23 V) Falling Propagation Delay vs. Temperature Rev. C | Page 6 of 12 Data Sheet ADM6305/ADM6306 10k 10k TRANSIENT DURATION (s) 5V TRANSIENT DURATION (s) 3V 10 1 0 200 400 600 800 1000 1200 OVERDRIVE, VREF - VRST IN (mV) Figure 11. Maximum Transient Duration vs. RST IN (VTH = 1.23 V) Threshold Overdrive 10mV/1s 40 20 40 60 80 TEMPERATURE (C) 100 120 125 09345-012 RST INx PROPAGATION DELAY (s) 60 20 200 300 Figure 13. Maximum Transient Duration vs. RST INx (VTH = 0.4 V) Threshold Overdrive 80 0 100 OVERDRIVE, VREF - VRST IN (mV) 1mV/1s -20 10 0 100 -40 100 1 120 0 1k 09345-013 TRANSIENT DURATION (s) TRANSIENT DURATION (s) 5V 100 09345-011 TRANSIENT DURATION (s) TRANSIENT DURATION (s) 3V 1k Figure 12. RST INx (VTH = 0.4 V) Falling Propagation Delay vs. Temperature Rev. C | Page 7 of 12 ADM6305/ADM6306 Data Sheet THEORY OF OPERATION The ADM6305/ADM6306 are compact, low power supervisory circuits capable of monitoring two voltage rails. If a monitored voltage drops below its associated threshold, the active low reset output asserts low. The ADM6305 monitors two supplies via two adjustable resistor-programmable undervoltage reset inputs. Both RST IN1 and RST IN2 have a reset threshold of either 0.4 V or 1.23 V depending on the particular model; that is, the RST IN1 and RST IN2 threshold of the ADM6305D3ARJZ-RL7 model is 1.23 V, while in the case of ADM6305D3ARJZ1-RL7 model, it is 0.4 V. The VCC input of the ADM6305 is not a monitored input. The ADM6306 has one adjustable undervoltage reset input, RST IN, which features a choice of reset threshold, 0.4 V or 1.23 V (see the Ordering Guide for more information). The ADM6306 incorporates a variety of internally pretrimmed VCC undervoltage threshold options for monitoring supply voltages in increments between 2.5 V to 5 V. The ADM6306 also includes a manual reset input. INPUT CONFIGURATION The threshold voltage at an adjustable input is either 0.4 V or 1.23 V. To monitor a voltage greater than the typical adjustable threshold, VRSTH, connect a resistor divider network to the circuit as depicted in Figure 14, where R1 R2 VTH VRSTH R2 on this input. The ADM6305/ADM6306 are powered via VCC. Figure 9 shows the maximum transient duration vs. VCC reset threshold overdrive, for which reset pulses are not generated. Figure 9 depicts the maximum pulse width that a negative going VCC transient may typically have without causing RESET to be asserted. As the amplitude of the transient increases, the maximum allowable pulse width decreases. The addition of a bypass capacitor on VCC provides additional transient immunity. RESET OUTPUT CONFIGURATION The ADM6305/ADM6306 are available in a choice of four reset timeouts. After the monitored supplies rise above their associated threshold level, the RESET signal remains low for the reset timeout period before deasserting. Subsequently, if a monitored supply falls below its associated threshold, the RESET output reasserts. The open-drain RESET output of the ADM6305/ADM6306 remains valid as long as VCC exceeds 0.9 V. The ADM6305 remains in UVLO when VCC is below 1.5 V. The RESET output is controlled by RTS INx if VCC exceeds 2.5 V. The open-drain RESET output allows the ADM6305 and ADM6306 to interface easily with microprocessors and devices with bidirectional reset pins. Connecting the supervisory devices RESET output directly to the microcontrollers RESET pin with a single pull-up resistor allows either device to issue a system reset (see Figure 15). VIN VCC ADM6305/ ADM6306 R2 VRSTH 09345-014 RESET MICROPROCESSOR RESET Figure 15. Interfacing to Microprocessors with Bidirectional RESET Output Figure 14. Setting the Adjustable Monitor The high input impedance (leakage of 25 nA) of the adjustable inputs minimizes the offset error caused by the leakage current and external resistor divider. This allows the user to apply a divider with large resistance to minimize the loss. The offset voltage caused by the leakage current is calculated by R1 x 25 nA. The RST INx inputs are designed to ignore fast voltage transients (see Figure 11 and Figure 12). Increase the noise immunity by connecting a 0.1 F bypass capacitor between RST INx and ground. Note that adding capacitance to RST INx slows the overall response time of the device. There is no hysteresis associated with the 0.4 V adjustable inputs; instead, a time-based glitch filter to prevent false triggering is used. The glitch filter avoids the need to use a portion of the operating supply range to provide hysteresis RPULL-UP 09345-015 R1 MANUAL RESET The ADM6306 features a manual reset input (MR) which, when driven low, asserts the reset output. When MR transitions from low to high, reset remains asserted for the duration of the reset active timeout period before deasserting. The MR input has a 63.5 k internal pull-up resistor so that the input is always high when unconnected. An external push-button switch can be connected between MR and ground so that the user can generate a reset. Debounce circuitry is integrated on-chip for this purpose. Noise immunity is provided on the MR input, and fast, negative going transients of up to 0.1 s (typical) are ignored. If required, a 0.1 F capacitor between MR and ground provides additional noise immunity. Rev. C | Page 8 of 12 Data Sheet ADM6305/ADM6306 DEVICE MODEL OPTIONS The ADM6305/ADM6306 include many device options; however, not all options are released for sale. Released options are called standard models and are listed in the Ordering Guide. For the most up to date list of standard models, check the Multi Voltage Monitors page on the Analog Devices website. Contact sales for information on nonstandard models and be aware that samples and production units have very long lead times. Table 6. ADM6306 VCC Reset Voltage Threshold Options Reset Threshold Number 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Min 2.463 2.591 2.66 2.758 2.886 2.955 3.034 3.152 3.251 3.349 3.448 3.546 3.645 3.743 3.842 3.94 4.039 4.137 4.236 4.314 4.433 4.561 4.63 4.728 4.827 4.925 TA = 25C Typ 2.5 2.63 2.7 2.8 2.93 3 3.08 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4 4.1 4.2 4.3 4.38 4.5 4.63 4.7 4.8 4.9 5.0 Max 2.538 2.669 2.741 2.842 2.974 3.045 3.126 3.248 3.35 3.451 3.553 3.654 3.756 3.857 3.959 4.06 4.162 4.263 4.365 4.446 4.568 4.699 4.771 4.872 4.974 5.075 Min 2.438 2.564 2.633 2.73 2.857 2.925 3.003 3.12 3.218 3.315 3.413 3.51 3.608 3.705 3.803 3.9 3.998 4.095 4.193 4.27 4.388 4.514 4.583 4.68 4.778 4.875 TA = -40C to +125C Max 2.563 2.696 2.768 2.87 3 3.075 3.157 3.28 3.383 3.485 3.588 3.69 3.793 3.895 3.998 4.1 4.203 4.305 4.408 4.49 4.613 4.746 4.818 4.92 5.023 5.125 Unit V V V V V V V V V V V V V V V V V V V V V V V V V V Table 7. Reset Timeout Options Reset Timeout Period Code ADM630xD1 ADM630xD2 ADM630xD3 ADM630xD4 Min 1.0 20 140 1120 TA = -40C to +125C Typ Max 1.4 2.0 28 40 200 280 1570 2240 Unit ms ms ms ms Table 8. Adjustable Input Threshold Options Model ADM6305_ _ _ _ _Z-RL7 ADM6305_ _ _ _ _Z1-RL7 ADM6306_ _ _ _ _ _ _Z-R7 ADM6306_ _ _ _ _ _ _Z1-R7 RST IN1 1.23 V 0.4 V N/A N/A Rev. C | Page 9 of 12 Monitored Input Threshold RST IN2 1.23 V 0.4 V N/A N/A RST IN N/A N/A 1.23 V 0.4 V ADM6305/ADM6306 Data Sheet ADM6305D_ARJZ_-RL7 TEMPERATURE RANGE A: -40C TO +125C RST IN1 & RST IN2 ADJUSTABLE THRESHOLD 1:0.4V & 0.4V BLANK: 1.23V & 1.23V PACKAGE DESIGNATOR RJ = SOT-23 Z = RoHs COMPLIANT 09345-016 PACKING MATERIAL RL7 = 7" TAPE & REEL (3000 PIECE QUANTITY) RESET TIMEOUT PERIOD CODE (1 TO 4) Figure 16. ADM6305 Ordering Code Structure ADM6306D_ _ _ARJZ_R7 PACKING MATERIAL R7 = 7" TAPE & REEL (3000 PIECE QUANTITY) RESET TIMEOUT (1 TO 4) RESET THRESHOLD NUMBER (SEE TABLE 6) Z = RoHs COMPLIANT PACKAGE DESIGNATOR RJ = SOT-23 09345-017 RST IN ADJUSTABLE THRESHOLD 1:0.4V DASH: 1.23V TEMPERATURE RANGE A: -40C TO +125C Figure 17. ADM6306 Ordering Code Structure Table 9. Standard Models Model ADM6305D3ARJZ-RL7 ADM6305D3ARJZ1-RL7 ADM6306D131ARJZ-R7 ADM6306D131ARJZ1R7 ADM6306D329ARJZ-R7 ADM6306D330ARJZ-R7 ADM6306D331ARJZ-R7 ADM6306D331ARJZ1R7 ADM6306D344ARJZ-R7 ADM6306D346ARJZ-R7 RST IN1 1.23 V 0.4 V N/A N/A N/A N/A N/A N/A N/A N/A Monitored Input Threshold RST IN2 VCC Reset 1.23 V N/A 0.4 V N/A N/A 3.08 V N/A 3.08 V N/A 2.93 V N/A 3V N/A 3.08 V N/A 3.08 V N/A 4.38V N/A 4.63 V Rev. C | Page 10 of 12 RST IN N/A N/A 1.23 V 0.4 V 1.23 V 1.23 V 1.23 V 0.4 V 1.23 V 1.23 V Minimum Reset Timeout 140 ms 140 ms 1 ms 1 ms 140 ms 140 ms 140 ms 140 ms 140 ms 140 ms Data Sheet ADM6305/ADM6306 OUTLINE DIMENSIONS 3.00 2.90 2.80 1.70 1.60 1.50 5 1 4 2 3.00 2.80 2.60 3 0.95 BSC 1.90 BSC 1.45 MAX 0.95 MIN 0.15 MAX 0.05 MIN 0.50 MAX 0.35 MIN 0.20 MAX 0.08 MIN 10 5 0 SEATING PLANE 0.60 BSC 0.55 0.45 0.35 11-01-2010-A 1.30 1.15 0.90 COMPLIANT TO JEDEC STANDARDS MO-178-AA Figure 18. 5-Lead Small Outline Transistor Package [SOT-23] (RJ-5) Dimensions shown in millimeters ROUND SPROCKET HOLES 09345-019 PIN 1 MARKER DIRECTION OF FEED Figure 19. ADM6305/ADM6306 Reel Orientation ORDERING GUIDE Model1, 2, 3 ADM6305D3ARJZ-RL7 ADM6305D3ARJZ1-RL7 ADM6306D131ARJZ-R7 ADM6306D131ARJZ1R7 ADM6306D329ARJZ-R7 ADM6306D330ARJZ-R7 ADM6306D331ARJZ-R7 ADM6306D331ARJZ1R7 ADM6306D344ARJZ-R7 ADM6306D346ARJZ-R7 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Ordering Quantity4 3,000 3,000 3,000 3,000 3,000 3,000 3,000 3,000 3,000 3,000 Package Description 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 1 Package Option RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 Marking Code LG9 LG8 LGA LGC LLY LM0 LG6 LQC LM1 LLZ ADM6305 and ADM6306 follow the C2 Pin 1 orientation standard for tape and reel packaging (see Figure 19). The ADM6305/ADM6306 include many device options, however, not all options are released for sale. Released options are called standard models and are listed in the Ordering Guide. For the most up to date list of standard models, check the Multi Voltage Monitors page on the Analog Devices website. Contact sales for information on nonstandard models and be aware that samples and production units have very long lead times. 3 Z = RoHS Compliant Part. 4 If ordering nonstandard models, complete the ordering code shown in Figure 16 and Figure 17 by inserting the reset threshold, reset timeout, and adjustable threshold suffixes. 2 Rev. C | Page 11 of 12 ADM6305/ADM6306 Data Sheet NOTES (c)2010-2018 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09345-0-4/18(C) Rev. C | Page 12 of 12