3.3V Surface Mount Crystal Clock Oscillator HSM6 Features: XO 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com 1.544 to 170 MHz 3.3V Operation Tri-State Enable/Disable Power Saving Function: 10uA When Disabled Overall Frequency Tolerance: HSM613 25 ppm HSM623 50 ppm HSM633 100 ppm Temperature Range: -40 to 85C Ceramic Surface Mount Package Tape and Reel Packaging The Connor-Winfield HSM613, HSM623, and HSM633 are 7.5mm x 5mm, 3.3V HCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. The surface mount package is designed for high-density mounting and is optimum for mass production Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Minimum -55 -0.5 Nominal - Maximum 125 7.0 Units C Vdc Notes Units MHz Notes ppm 1 Operating Specifications Parameter Frequency Range (Fo) HSM613 HSM623 HSM633 Frequency Tolerance HSM613 HSM623 HSM633 Operating Temp Range Supply Voltage (Vdd) Supply Current (Icc) 1.544 to 31.999 MHz 32 to 49.999 MHz 50 to 66.999 MHz 67 to 124.999 MHz 125 to 170 MHz Minimum 1.544 Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Output Disable Current (lcc) Minimum 70% Vdd - -25 -50 -100 -40 3.0 - Nominal - - 3.3 - Maximum 125 170 170 25 50 100 85 3.6 15 20 25 40 50 C Vdc mA Input Characteristics Nominal - Maximum 30% Vdd 10 150 10 Units Vdc Vdc mS nS uA Notes 2 Units pF Notes HCMOS Output Characteristics US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Bulletin Page Revision Date Sm044 1 of 2 08 12 May 2004 Parameter Load (Voh) Voltage High Low (Vol) (loh) Current High Low (lol) Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Start-Up Time Jitter (10 Hz to 20 MHz) (12 kHz to 20 MHz) Minimum 2.91 -2 45 - Nominal 50 - Maximum 15 0.33 2 55 6 10 5 1 Vdc mA % nS mS pS RMS Notes: 1. Inclusive of calibration @ 25C , frequency stability vs temperature, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator output is enabled with no connection on pad 1 Specifications subject to change without notice. All dimensions in inches. (c) Copyright 1998 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Suggested Pad Layout Hermetically sealed ceramic package and metal cover Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55C / 30 minutes and +125C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125C 5C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering General Conditions 260C max x 10 sec max x 2 times max or 230C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215C, 50 sec at 215C, then down to room temperature per 1 to 5C / sec Test Circuit Mechanical Characteristics Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260C max x 10 sec max x 2 times, or 230C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235C 5C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec 0.5 sec into solder bath Output Waveform After performing the above procedures, a newly soldered coverage shall be greater than 90% Pin Connections 1: Tri-State E/D 2: Ground 3: Output 4: VDD Dimensional Tolerance: .02" (.508mm) .005" (.127mm) Tape and Reel Dimensions Ordering Information HSM633 - 125.00 MHz CLOCK SERIES CENTER FREQUENCY Bulletin Dimensional Tolerance: .02" (. .005" (.1 Page Revision Date Specifications subject to change without notice. All dimensions in inches. (c) Copyright 1998 The Connor-Winfield Corporation Sm044 2 of 2 08 12 May 2004