INCH-POUND MIL-PRF-39019/1H 14 May 2010 SUPERSEDING MIL-PRF-39019/1G 27 August 1997 PEROFRMANCE SPECIFICATION SHEET CIRCUIT BREAKERS, MAGNETIC, LOW-POWER, SEALED, TRIP-FREE ONE-POLE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39019. FIGURE 1. Circuit breaker configuration. AMSC N/A FSC 5925 MIL-PRF-39019/1H FIGURE 1. Circuit breaker configuration - Continued. 2 MIL-PRF-39019/1H Inches .005 .030 .060 .062 .063 .125 .138 .240 .250 .325 .332 mm 0.13 0.76 1.52 1.57 1.60 3.18 3.51 6.10 6.35 8.26 8.43 Inches .375 .380 .493 .507 .610 .625 .641 .906 1.562 1.700 1.780 mm 9.52 9.65 12.52 12.88 15.49 15.88 16.28 23.01 39.67 43.18 45.21 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .031 (0.79 mm). 4. The shape of the circuit breaker is shown for information only. Slight deviations from this outline drawing, which do not alter the functional aspect of the device, are acceptable. 5. Hex mounting nut .375-32 UNEF-2B thread, .093 .005 (2.36 mm 0.13 mm) thick or equivalent MS25082-20, -B20. 6. Internal tooth lockwasher, .507/.493 O.D., .392/.382 I.D., .025 .005 (0.64 mm 0.13mm) thick, stainless steel or equivalent MS35333-134. 7. The effective bushing thread length (not including mounting hardware) is .280 (7.11 mm) minimum. 8. Marking may appear on any surface except the mounting surface. 9. Lock ring not required if on-off plate has locking tab. 10. Numerical marking optional on circuit diagram. 11. For configuration 2 add "S" at end of dash number for screw terminals with insulating block (see table I). When circuit breakers are subjected to the resistance to solvents test, the insulating block shall be removed and shall not be tested. Main terminal screw MS35265-26 or equivalent. FIGURE 1. Circuit breaker configuration - Continued. 3 MIL-PRF-39019/1H REQUIREMENTS: Dimensions and configuration: See figure 1 and note 11. Weight: For reference only, approximately 50 grams. Mounting hardware: See figure 1. Terminals: See figure 1. Voltage and frequency rating: 50 V dc, maximum and 240 V ac, maximum at 60 Hz and 400 Hz. High inrush: 800 percent at 60 Hz and dc, 1,400 percent at 400 Hz (see table I). Current rating: See table I. Circuit diagram: See figure 1. Time delay: See table I. Resistance or impedance: See table I. Part or Identifying Number (PIN): The PIN shall be M39019/01-(dash number taken from table I) (e.g., M39019/01-200, M39019/01-200S). Cross reference: See table II. TABLE I. Circuit breaker dash numbers and applicable characteristics. Dash number 1/ Standard delay 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 High inrush 300 301 --302 303 --304 305 --306 307 --308 309 --310 Current rating (amps) Time delay Resistance or impedance (ohms - max) 2/ DC 0.05 0.05 0.05 0.1 0.1 0.1 0.25 0.25 0.25 0.5 0.5 0.5 0.75 0.75 0.75 1.0 A B C A B C A B C A B C A B C A See footnotes at end of table. 4 680.0 680.0 680.0 150.0 150.0 150.0 20.0 20.0 20.0 5.4 5.4 5.4 2.5 2.5 2.5 1.35 60 Hz 690.0 690.0 690.0 170.0 170.0 170.0 26.0 26.0 26.0 6.0 6.0 6.0 2.7 2.7 2.7 1.5 400 Hz 710.0 710.0 710.0 180.0 180.0 180.0 27.0 27.0 27.0 6.6 6.6 6.6 2.8 2.8 2.8 1.61 MIL-PRF-39019/1H TABLE I. Circuit breaker dash numbers and applicable characteristics - Continued. Dash number 1/ Standard delay 216 217 260 261 262 263 264 265 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 High inrush 311 --340 341 --342 343 --312 313 --314 315 --316 317 --318 319 --320 321 --322 323 --324 325 --326 327 --328 329 --- Current rating (amps) Time delay Resistance or impedance (ohms - max) 2/ DC 1.0 1.0 1.25 1.25 1.25 1.5 1.5 1.5 2.0 2.0 2.0 2.5 2.5 2.5 3.0 3.0 3.0 4.0 4.0 4.0 5.0 5.0 5.0 6.0 6.0 6.0 7.0 7.0 7.0 7.5 7.5 7.5 8.0 8.0 8.0 B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C A B C See footnotes at end of table. 5 1.35 1.35 0.9 0.9 0.9 0.65 0.65 0.65 0.40 0.40 0.40 0.25 0.25 0.25 0.15 0.15 0.15 0.10 0.10 0.10 0.061 0.061 0.061 0.042 0.042 0.042 0.036 0.036 0.036 0.031 0.031 0.031 0.027 0.027 0.027 60 Hz 1.5 1.5 1.0 1.0 1.0 0.70 0.70 0.70 0.40 0.40 0.40 0.25 0.25 0.25 0.15 0.15 0.15 0.10 0.10 0.10 0.063 0.063 0.063 0.043 0.043 0.043 0.036 0.036 0.036 0.031 0.031 0.031 0.028 0.028 0.028 400 Hz 1.61 1.61 1.1 1.1 1.1 0.75 0.75 0.75 0.50 0.50 0.50 0.27 0.27 0.27 0.17 0.17 0.17 0.12 0.12 0.12 0.072 0.072 0.072 0.050 0.050 0.050 0.040 0.040 0.040 0.038 0.038 0.038 0.035 0.035 0.035 MIL-PRF-39019/1H TABLE I. Circuit breaker dash numbers and applicable characteristics - Continued. Dash number 1/ Standard delay 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 High inrush 330 331 --332 333 --334 335 --336 337 --338 339 --- Current rating (amps) Time delay Resistance or impedance (ohms - max) 2/ DC 9.0 9.0 9.0 10.0 10.0 10.0 12.5 12.5 12.5 15.0 15.0 15.0 20.0 20.0 20.0 A B C A B C A B C A B C A B C 0.022 0.022 0.022 0.018 0.018 0.018 0.012 0.012 0.012 0.009 0.009 0.009 0.006 0.006 0.006 60 Hz 0.022 0.022 0.022 0.021 0.021 0.021 0.013 0.013 0.013 0.009 0.009 0.009 0.006 0.006 0.006 400 Hz 0.028 0.028 0.028 0.024 0.024 0.024 0.015 0.015 0.015 0.010 0.010 0.010 0.007 0.007 0.007 1/ For configuration 2, add "S" at end of dash number. 2/ The corresponding maximum wattage losses, which in no case shall exceed 3.0 watts, may be calculated as 2 2 I R or I Z. 6 MIL-PRF-39019/1H TABLE II. Cross reference of superseded part numbers. Superseded MIL-C-39019/1B part number M39019/11 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 New part number M39019/01200 201 200 201 200 201 200 201 200 201 209 210 209 210 209 210 209 210 209 210 215 216 215 216 215 216 215 216 215 216 224 225 224 225 224 225 224 225 224 225 Superseded MIL-C-39019/1B part number M39019/141 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 New part number M39019/01230 231 230 231 230 231 230 231 230 231 248 249 248 249 248 249 248 249 248 249 254 255 254 255 254 255 254 255 254 255 257 258 257 258 257 258 257 258 257 258 7 Superseded MIL-C-39019/1B part number M39019/181 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 New part number M39019/01218 219 218 219 218 219 227 228 227 228 227 228 233 234 233 234 233 234 236 237 236 237 236 237 242 243 242 243 242 243 245 246 245 246 245 246 251 252 251 252 251 252 MIL-PRF-39019/1H The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Army - CR Navy - EC Air Force - 85 DLA - CC Preparing activity: Army - CR Agent: DLA - CC Review activities: Army - AT, AV, MI Navy - AS, MC Air Force - 19, 99 (Project 5925-2009-032) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.daps.dla.mil. 8