Order this document by BAV99WT1/D SEMICONDUCTOR TECHNICAL DATA # ! $" Motorola Preferred Devices The BAV99WT1 is a smaller package, equivalent to the BAV99LT1. Suggested Applications 3 * ESD Protection * Polarity Reversal Protection 1 2 * Data Line Protection ANODE 1 * Inductive Load Protection * Steering Logic 3 CATHODE/ANODE MAXIMUM RATINGS (EACH DIODE) Symbol Value Unit Reverse Voltage VR 70 Vdc Forward Current IF 215 mAdc IFM(surge) 500 mAdc Repetitive Peak Reverse Voltage VRRM 70 V Average Rectified Forward Current(1) (averaged over any 20 ms period) IF(AV) 715 mA Repetitive Peak Forward Current IFRM 450 mA Non-Repetitive Peak Forward Current t = 1.0 ms t = 1.0 ms t = 1.0 S IFSM Rating Peak Forward Surge Current CATHODE 2 BAV99WT1 CASE 419-02, STYLE 9 SC-70/SOT-323 CATHODE 1 ANODE 2 3 CATHODE/ANODE A BAV99RWT1 CASE 419-02, STYLE 10 SC-70/SOT-323 2.0 1.0 0.5 THERMAL CHARACTERISTICS Characteristic Total Device Dissipation FR-5 Board,(1) TA = 25C Derate above 25C Thermal Resistance Junction to Ambient Total Device Dissipation Alumina Substrate,(2) TA = 25C Derate above 25C Thermal Resistance Junction to Ambient Junction and Storage Temperature Symbol Max Unit PD 200 mW 1.6 mW/C RqJA 625 C/W PD 300 mW 2.4 mW/C RqJA 417 C/W TJ, Tstg - 65 to +150 C 1. FR-5 = 1.0 0.75 0.062 in. 2. Alumina = 0.4 0.3 0.024 in. 99.5% alumina. DEVICE MARKING BAV99WT1 = A7 BAV99RWT1 = F7 Thermal Clad is a trademark of the Bergquist Company. Preferred devices are Motorola recommended choices for future use and best overall value. Motorola, Small-Signal Inc. 1996 Motorola Transistors, FETs and Diodes Device Data 1 ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) (EACH DIODE) Characteristic Symbol Min Max Unit V(BR) 70 -- Vdc Reverse Voltage Leakage Current (VR = 70 Vdc) (VR = 25 Vdc, TJ = 150C) (VR = 70 Vdc, TJ = 150C) IR -- -- -- 2.5 30 50 Diode Capacitance (VR = 0, f = 1.0 MHz) CD -- 1.5 pF Forward Voltage VF -- -- -- -- 715 855 1000 1250 mVdc trr -- 6.0 ns VFR -- 1.75 V OFF CHARACTERISTICS Reverse Breakdown Voltage (I(BR) = 100 A) (IF = 1.0 mAdc) (IF = 10 mAdc) (IF = 50 mAdc) (IF = 150 mAdc) Reverse Recovery Time (IF = IR = 10 mAdc, iR(REC) = 1.0 mAdc) (Figure 1) RL = 100 W Forward Recovery Voltage (IF = 10 mA, tr = 20 ns) mAdc 820 +10 V 2k 100 H 0.1 F tr IF 0.1 F tp t IF trr 10% t DUT 50 OUTPUT PULSE GENERATOR 50 INPUT SAMPLING OSCILLOSCOPE 90% IR VR INPUT SIGNAL iR(REC) = 1 mA OUTPUT PULSE (IF = IR = 10 mA; measured at iR(REC) = 1 mA) Notes: 1. A 2.0 k variable resistor adjusted for a Forward Current (IF) of 10 mA. Notes: 2. Input pulse is adjusted so IR(peak) is equal to 10 mA. Notes: 3. tp trr Figure 1. Recovery Time Equivalent Test Circuit 2 Motorola Small-Signal Transistors, FETs and Diodes Device Data CURVES APPLICABLE TO EACH DIODE 10 100 I R, REVERSE CURRENT ( A) IF, FORWARD CURRENT (mA) TA = 150C 10 TA = 85C TA = 25C 1.0 TA = 125C 1.0 TA = 85C 0.1 TA = 55C 0.01 TA = - 40C TA = 25C 0.1 0.2 0.4 0.6 0.8 1.0 VF, FORWARD VOLTAGE (VOLTS) 0.001 1.2 0 10 Figure 2. Forward Voltage 20 30 40 VR, REVERSE VOLTAGE (VOLTS) 50 Figure 3. Leakage Current CD , DIODE CAPACITANCE (pF) 0.68 0.64 0.60 0.56 0.52 0 2 4 6 8 VR, REVERSE VOLTAGE (VOLTS) Figure 4. Capacitance Motorola Small-Signal Transistors, FETs and Diodes Device Data 3 INFORMATION FOR USING THE SC-70/SOT-323 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection 0.025 0.025 0.65 0.65 0.075 1.9 0.035 0.9 0.028 inches 0.7 mm SC-70/SOT-323 SC-70/SOT-323 POWER DISSIPATION The power dissipation of the SC-70/SOT-323 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by T J(max), the maximum rated junction temperature of the die, RJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA . Using the values provided on the data sheet for the SC-70/SOT-323 package, PD can be calculated as follows: PD = TJ(max) - TA RJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25C, one can calculate the power dissipation of the device which in this case is 200 milliwatts. PD = 150C - 25C 625C/W = 200 milliwatts The 625C/W for the SC-70/SOT-323 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 200 milliwatts. There are other alternatives to achieving higher power dissipation from the SC-70/SOT-323 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. 4 SOLDERING PRECAUTIONS The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. * Always preheat the device. * The delta temperature between the preheat and soldering should be 100C or less.* * When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10C. * The soldering temperature and time shall not exceed 260C for more than 10 seconds. * When shifting from preheating to soldering, the maximum temperature gradient shall be 5C or less. * After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. * Mechanical stress or shock should not be applied during cooling. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. Motorola Small-Signal Transistors, FETs and Diodes Device Data PACKAGE DIMENSIONS A L NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3 B S 1 2 D V G C 0.05 (0.002) R N J K H CASE 419-02 ISSUE H SC-70/SOT-323 Motorola Small-Signal Transistors, FETs and Diodes Device Data DIM A B C D G H J K L N R S V INCHES MIN MAX 0.071 0.087 0.045 0.053 0.035 0.049 0.012 0.016 0.047 0.055 0.000 0.004 0.004 0.010 0.017 REF 0.026 BSC 0.028 REF 0.031 0.039 0.079 0.087 0.012 0.016 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.90 1.25 0.30 0.40 1.20 1.40 0.00 0.10 0.10 0.25 0.425 REF 0.650 BSC 0.700 REF 0.80 1.00 2.00 2.20 0.30 0.40 STYLE 9: PIN 1. ANODE 2. CATHODE 3. CATHODE-ANODE STYLE 10: PIN 1. CATHODE 2. ANODE 3. ANODE-CATHODE 5 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 6 Motorola Small-Signal Transistors, FETs and Diodes Device Data BAV99WT1/D