October 2009 Doc ID 16571 Rev 1 1/13
13
LY3200ALH
MEMS motion sensor:
high performance ±2000 dps analog yaw-rate gyroscope
Features
2.7 V to 3.6 V single supply operation
Wide extended operating temperature range
(-40°C to +85°C)
High stability over temperature
Analog absolute angular-rate output
Integrated low-pass filters
Low power consumption
Sleep mode
Embedded power-down
Embedded self-test
High shock and vibration survivability
ECOPACK® RoHS and “Green” compliant
(see Section 6)
Applications
Gaming applications
Pointing devices, remote and game controllers
Motion control with user interface
Industrial and robotics
Description
The LY3200ALH is a high performance low-power
single-axis micromachined gyroscope capable of
measuring angular rate along yaw axis.
It provides excellent temperature stability and
high resolution over extended operating
temperature range (-40°C to +85°C).
The LY3200ALH has a full scale of ±2000 dps and
is capable of detecting rates with a -3 dB
bandwidth up to 140 Hz.
The device includes a sensing element composed
of a single driving mass, kept in continuous
oscillation and capable of reacting, based on the
Coriolis principle, when an angular rate is applied.
A CMOS IC provides the measured angular rate
to the external world through an analog output
voltage, allowing high levels of integration and
production trimming to better match sensing
element characteristics.
ST's family of gyroscopes leverages on the
mature and robust manufacturing process already
used for the production of micro-machined
accelerometers.
ST is already in the field with several hundred
million sensors which have received excellent
acceptance from the market in terms of quality,
reliability and performance.
The LY3200ALH is available in a plastic land grid
array (LGA) package, which ST successfully
pioneered for accelerometers. Today ST has the
widest manufacturing capability and strongest
expertise in the world for production of sensors in
plastic LGA packages.
LGA-10
(3x5x1 mm)
Table 1. Device summary
Order code Temperature range (°C) Package Packing
LY3200ALH -40 to +85 LGA-10 (3x5x1) Tray
LY3200ALHTR -40 to +85 LGA-10 (3x5x1) Tape and reel
www.st.com
Contents LY3200ALH
2/13 Doc ID 16571 Rev 1
Contents
1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Mechanical and electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Zero-rate level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.4 Sleep mode, self test and power down . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1 Output response vs. rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2 Soldering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LY3200ALH Block diagram and pin description
Doc ID 16571 Rev 1 3/13
1 Block diagram and pin description
Figure 1. Block diagram
1.1 Pin description
Figure 2. Pin connection
$%-/$5,!4/2
#(!2'%
!-0,)&)%2 37)4#(%$
,/70!33
#!0! #)4/2
&),4%
2
:Z
/54:
&EEDBACKLOOP
'.$
#/
.44)-%
,0&),4%2
!-V
2%&%2%.#% 42)--).'
#)2#5)43 #,/#+ 0(!3%
'%.%2!4/2
%3*7*/(."44
4/06)%7
$)2%#4)/./&4(%
$%4%#4!",%
!.'5,!22!4% "/44/-6)%7


:Z'.$6$$
/54:
6#/.434
6$$ 6REF
2%
3
2%3
3,%%00$
!-V
Block diagram and pin description LY3200ALH
4/13 Doc ID 16571 Rev 1
Table 2. Pin description
Pin # Pin name Analog function
1 Vdd Power supply
2 ST Self-test (see Table 6)
3 VCONT PLL filter connection
4 GND 0V supply voltage
5 Res Leave unconnected or connect to Vdd
6 OUTZ Z axis output voltage
7 Vref Reference voltage
8 SLEEP/PD Sleep mode / power-down mode (see Table 6)
9 Vdd Power supply
10 Res Leave unconnected or connect to Vdd
LY3200ALH Mechanical and electrical specifications
Doc ID 16571 Rev 1 5/13
2 Mechanical and electrical specifications
2.1 Mechanical characteristics
Vdd = 3 V, T = 25 °C unless otherwise noted (a)
a. The product is factory calibrated at 3 V. The operational power supply range is specified in Table 4.
Table 3. Mechanical characteristics
Symbol Parameter Test condition Min. Typ.(1) Max. Unit
FS Measurement range ±2000 dps
So Sensitivity(2) 0.67 mV/dps
SoDr Sensitivity change vs.
temperature Delta from 25°C 0.01 %/°C
Voff Zero-rate level(3) 1.5 V
OffDr Zero-rate level change
vs. temperature Delta from 25°C 0.09 dps/°C
NL Non linearity Best fit straight line ±1 % FS
BW Bandwidth(3) 140 Hz
Vst Self-test output change 400(4) mV
Rn Rate noise density 0.074 dps/ Hz
To p Operating temperature
range -40 +85 °C
1. Typical specifications are not guaranteed.
2. Sensitivity and zero-rate offset are not ratiometric to supply voltage.
3. The product is capable of measuring angular rates extending from DC to the selected BW.
4. Self test typical absolute value.
Mechanical and electrical specifications LY3200ALH
6/13 Doc ID 16571 Rev 1
2.2 Electrical characteristics
Vdd = 3 V, T = 25 °C unless otherwise noted (b)
.
b. The product is factory calibrated at 3 V
Table 4. Electrical characteristics
Symbol Parameter Test condition Min. Typ.(1) Max. Unit
Vdd Supply voltage 2.7 3 3.6 V
Idd Supply current 4.2 mA
IddSl Supply current sleep
mode 2.2 mA
IddPdn Supply current power-
down mode 5µA
VST Self-test input Logic 0 level 0 0.2*Vdd V
Logic 1 level 0.8*Vdd Vdd
VPD Power-down input Logic 0 level 0 0.2*Vdd V
Logic 1 level 0.8*Vdd Vdd
To p Operating temperature
range -40 +85 °C
1. Typical specifications are not guaranteed.
LY3200ALH Absolute maximum ratings
Doc ID 16571 Rev 1 7/13
3 Absolute maximum ratings
Stresses above those listed as Absolute maximum ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 5. Absolute maximum ratings
Symbol Ratings Maximum value Unit
Vdd Supply voltage -0.3 to 6 V
Vin Input voltage on any control pin (SLEEP/PD, ST) -0.3 to Vdd +0.3 V
A Acceleration 3000 for 0.5 ms g
10000 for 0.1 ms g
TSTG Storage temperature range -40 to +125 °C
ESD Electrostatic discharge protection 2 (HBM) kV
This is a mechanical shock sensitive device, improper handling can cause permanent
damage to the part
This is an ESD sensitive device, improper handling can cause permanent damage to
the part
Terminology LY3200ALH
8/13 Doc ID 16571 Rev 1
4 Terminology
4.1 Sensitivity
An angular rate gyroscope is a device that produces a positive-going output voltage for
counterclockwise rotation around the sensitive axis considered. Sensitivity describes the
gain of the sensor and can be determined by applying a defined angular velocity to it. This
value changes very little over temperature and time.
4.2 Zero-rate level
Zero-rate level describes the actual output signal if there is no angular rate present. The
zero-rate level of precise MEMS sensors is, to some extent, a result of stress to the sensor
and therefore zero-rate level can slightly change after mounting the sensor onto a printed
circuit board or after exposing it to extensive mechanical stress. This value changes very
little over temperature and time.
4.3 Self-test
Self-test allows testing of the mechanical and electrical part of the sensor, allowing the
seismic mass to be moved by means of an electrostatic test-force. The self-test function is
off when the ST pin is connected to GND. When the ST pin is tied to Vdd, an actuation force
is applied to the sensor, emulating a definite Coriolis force. In this case the sensor output
exhibits a voltage change in its DC level which is also dependent on the supply voltage.
When ST is active, the device output level is given by the algebraic sum of the signals
produced by the velocity acting on the sensor and by the electrostatic test-force. If the output
signals change within the amplitude specified in Table 3, then the mechanical element is
working properly and the parameters of the interface chip are within the defined
specifications.
4.4 Sleep mode, self test and power down
The LY3200ALH enables advanced power-saving features thanks to the availability of three
different operating modes. When the device is set in a Sleep mode configuration, the
reading chain is completely turned off, resulting in low power consumption. In this condition
the device turn-on time is significantly reduced, allowing simple external power cycling.
In accordance with the table below, the user can select the desired operating mode using
two dedicated pins (ST and SLEEP/PD).
Table 6. Sleep mode and Power-down mode configuration
Operating mode ST pin SLEEP/PD pin
Normal mode 0 0
Sleep mode 0 1
Self-test 1 0
Power-down 1 1
LY3200ALH Application hints
Doc ID 16571 Rev 1 9/13
5 Application hints
Figure 3. LY3200ALH electrical connections and external components values
Power supply decoupling capacitors should be placed in combination with an LDO regulator
(common design practice).
The LY3200ALH IC includes a PLL (phase-locked loop) circuit to synchronize driving and
sensing interfaces. Capacitors and resistors must be added at VCONT pin 3 (as shown in
Figure 3) to implement a low-pass filter.
100 nF
10kOhm470nF
Supply
C2
R1
C1
GND
1 µF
10nF
SLEEP/PD
GND
OUT Z
96
14
10 5
GND
ST
Vref
TOP VIEW
(TOP VIEW)
DIRECTION OF THE
DETECTABLE
ANGULAR RATE
+
z
LDO
2.2Ohm
GND
AM03841v
1
Application hints LY3200ALH
10/13 Doc ID 16571 Rev 1
5.1 Output response vs. rotation
Figure 4. Output response vs. rotation
5.2 Soldering information
The LGA package is compliant with the ECOPACK®, RoHS and Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020.
Leave “Pin 1 indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com
Steady state position
OUTZ = 1.5V
+Ωz
+Ωz
Positive rotations, as indicated by the arrow,
OUTZ= 1.5V + So*2000 = 2.62V
increase output value over zero-rate level:
AM03842v1
LY3200ALH Package information
Doc ID 16571 Rev 1 11/13
6 Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
Figure 5. LGA-10: mechanical data and package dimensions
A1 1.100
A2 0.855
A30.200
D1 2.850 3.000 3.150
E1 4.850 5.000 5.150
L0.635
L1 4.100
L2 2.200
N1 1.415
N2 1.100
M0.075
P1 1.300
P2 0.500
T1 0.600
T2 0.700
d0.200
k0.050
h0.100
LGA-10 (3x5x1mm)
Land Grid Array Package
8161636A
Revision history LY3200ALH
12/13 Doc ID 16571 Rev 1
7 Revision history
Table 7. Document revision history
Date Revision Changes
29-Oct-2009 1 First issue
LY3200ALH
Doc ID 16571 Rev 1 13/13
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com