Ultra subminiature Toggle Switch A9TS Ultra subminiature size. * Gold-plated clip contact ensure high reliability. * The sealed bottom prevents flux penetration. * Washable, equivalent to IP64 (IEC-60529). * A9TS is smaller than A9T. Height: A9T 17mm A9TS 11mm (35% smaller than A9T) RoHS Compliant Typical Applications Security Control Boards Electric Power Instrumentation Program Controllers List of Models Actuator Shape Standard Terminal Shape DIP Terminal Right Angle Terminal Vertical Mount Terminal Switching Functions SPDT DPDT SPDT DPDT SPDT DPDT A9TS21-0013 ON - ON A9TS11-0011 A9TS21-0011 A9TS11-0012 A9TS21-0012 A9TS11-0013 ON OFF ON A9TS12-0011 A9TS22-0011 A9TS12-0012 A9TS22-0012 A9TS12-0013 Quantity per tray Note: 100 25 A9TS22-0013 50 1. Lever do not stop at "-" position. 2. Switching Functions show the view from the side of Type and Brand name marking. Ratings/Characteristics Rating (resistive load) 14 mA at 28 VAC/DC, 0.1 A (minimum current) at 20 mVAC/DC Ambient operating temperature -20 C to +80 C 60% RH max. (with no icing or condensation) Ambient operating humidity 45 to 85% RH (at +5 to +35 C) Insulation resistance 500 M min. (at 500 VDC with insulation tester) Contact resistance (initial value) 80 m max. Dielectric strength 500 VAC for 1min between terminals, between terminals and ground Vibration resistance Malfunction 10 to 55 Hz, 1.5-mm double amplitude Shock resistance Malfunction 500 m/s2 min. Durability Mechanical 50,000 operations min. Electrical 50,000 operations min. Degree of protection IEC IP64 Washing Possible Operating forcse 4.9 N max. Weight 0.3 g 1 A9TS A9TS Dimensions DIP Terminal Models (Unit: mm) 11 3.8 1.6 2.54 0.3 (5.6) 1.7 dia. 0.2 0.45 (6) 2.54 284 7 2.54 (4) (6) (3) (2) (5) (2) (1) (4) (1) Single Pole Type Marking Side Note: (3) Double Pole Type NO.(4) and (6) terminals in the SPDT models are dummys to support the Switch case. Right Angle Terminal Models 11 3.8 1.6 (5.6) 1.7 dia. 0.2 0.45 2.54 284 2.54 7 (3) (6) (3) (2) (5) (2) (1) (4) (1) Single Pole Type Marking Side Double Pole Type 0.3 2.6 3.1 5.08 2.54 Vertical Mount Terminal Models 11 3.8 1.6 2.54 0.3 (5.6) 1.7 dia. 284 7 Marking Side 2 (6) (3) (2) (5) (2) (1) (4) (1) 0.45 5.08 Note: (3) 2.54 2.54 Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. Single Pole Type Double Pole Type A9TS A9TS PCB Dimensions (Top View) DIP Terminal Models Right Angle Terminal Models 2.54 Five-0.6 +0.1 0 dia. (4) (4) (1) (3) Five-0.6 +0.1 0 dia. (3) 5.08 (2) (6) Single Pole Type 5.08 (1) (5) 5.08 (2) (6) 2.54 Six-0.6 +0.1 0 dia. (2) 2.54 Eight-0.6 +0.1 0 dia. (3) (6) (2) (5) (1) (4) 5.08 (1) (3) Double Pole Type 5.08 Single Pole Type 5.08 Double Pole Type Vertical Mount Terminal Models 2.54 2.54 5.08 5.08 (1) (2) (4) (1) (5) (2) (6) (3) 5.08 (3) Eight-0.6 +0.1 0 dia. Five-0.6 +0.1 0 dia. Single Pole Type 5.08 Double Pole Type Switching Function / Internal Connections Switching Functions ON - ON 2 SPDT Models ON OFF 3 1 ON 3 3 2 1 2 1 ON - ON 2 DPDT Models 5 ON OFF ON 3 1 6 2 2 4 5 Note: 3 1 6 4 5 3 1 6 4 Lever do not stop at "-" position. 3 A9TS A9TS Safety Precautions Be sure to read the Safety precautions common to all PCB-mount Manual Switch for correct use. Cautions Use the switch within the rated voltage and current ranges, otherwise the Switch may have a shortened life expectancy, radiate heat,or burn out. This particularly applies to the instantaneous voltages and currents when switching. Using Flux Making mistakes in the type of flux or in the amount or method in which it is applied can cause flux to enter the interior of the Switch, with adverse effects on Switch performance. Assess the proper flux, conditions,and methods prior to using it. Hardling Do not apply excessive operating force to the Switch. Otherwise the Switch may be damaged or deformed, and the switch mechanism may malfunction as a result. Apply an operating force not exceeding 9.8N {1,000gf}. Apply the operating load from the top of the actuator. Do not apply a load from angle or from side the actuator. Doing so may deform the Switch contact. RoHS Compliant The "RoHS Compliant" designation indicates that the listed models do not contain the six hazardous substances covered by the RoHS Directive. Reference: The following standards are used to determine compliance for the six substances. * Lead: 1,000 ppm max. * Mercury: 1,000 ppm max. * Cadmium: 100 ppm max. * Hexavalent chromium: 1,000 ppm max. * PBB: 1,000 ppm max. * PBDF: 1,000 ppm max. Soldering Observe the following conditions when soldering the Switch. Automatic Soldering Bath Soldering temperature: 260 C max. (Preheating: 100 C 120s max.) Soldering time: 5s max. Manual Soldering Soldering temperature: 350 C at the tip of the soldering iron. Soldering time: 3s max. Washing Apply alcohol based solvents to clean. Do not clean the Switch immediately after soldering. Wait for at least five minutes after soldering before cleaning. Ultrasonic cleaning is not available dip into Switch washing agents for two minutes maximum. Environment for Storage and Use To prevent discoloration of the terminals and other problems during storage, do not store the Switch in locations subject to the following conditions. 1. High temperature or humidity 2. Corrosive gases 3. Direct sunlight Also, the Switch is not waterproof or splash-resistance. Do not use the Switch in locations that are subject to contact with water. Do not subject the Switch to freezing or condensation. * Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product. * Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or equipment, and be sure to provide the system or equipment with double safety mechanisms. Note: Do not use this document to operate the Unit. OMRON Corporation Electronic and Mechanical Components Company Contact: www.omron.com/ecb Cat. No. A199-E1-04 1014(0207)(O) Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: A9TS12-0013 A9TS11-0011 A9TS11-0013 A9TS12-0011 A9TS12-0012 A9TS21-0012 A9TS21-0013 A9TS220011 A9TS22-0012 A9TS22-0013 A9TS21-0011 A9TS11-0012