1
A9TS
Ultra subminiature Toggle Switch
Ultra subminiature size.
•
Gold-plated clip contact ensure high reliability.
•
The sealed bottom prevents flux penetration.
•
Washable, equivalent to IP64 (IEC-60529).
•A9TS is smaller than A9T.
Height: A9T 17mm A9TS 11mm (35% smaller than A9T)
■List of Models
Note: 1. Lever do not stop at "-" position.
2. Switching Functions show the view from the side of Type and Brand name marking.
■Ratings/Characteristics
RoHS Compliant
Actuator Shape Standard
Terminal Shape DIP Terminal Right Angle Terminal Vertical Mount Terminal
Switching Functions
SPDT DPDT SPDT DPDT SPDT DPDT
ON −ON A9TS11-0011 A9TS21-0011 A9TS11-0012 A9TS21-0012 A9TS11-0013 A9TS21-0013
ON OFF ON A9TS12-0011 A9TS22-0011 A9TS12-0012 A9TS22-0012 A9TS12-0013 A9TS22-0013
Quantity per tray 100 25 50
Rating (resistive load) 14 mA at 28 VAC/DC, 0.1 μA (minimum current) at 20 mVAC/DC
Ambient operating temperature −20 °C to +80 °C 60% RH max. (with no icing or condensation)
Ambient operating humidity 45 to 85% RH (at +5 to +35 °C)
Insulation resistance 500 MΩ min. (at 500 VDC with insulation tester)
Contact resistance (initial value) 80 mΩ max.
Dielectric strength 500 VAC for 1min between terminals, between terminals and ground
Vibration resistance Malfunction 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance Malfunction 500 m/s2 min.
Durability Mechanical 50,000 operations min.
Electrical 50,000 operations min.
Degree of protection IEC IP64
Washing Possible
Operating forcse 4.9 N max.
Weight 0.3 g
Security Control Boards
Electric Power Instrumentation
Program Controllers
Typical Applications
2
A9TSA9TS
■Dimensions (Unit: mm)
●DIP Terminal Models
Note: NO.(4) and (6) terminals in the SPDT models are dummys to support the Switch case.
●Right Angle Terminal Models
●Vertical Mount Terminal Models
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
11
3.8
(5.6)
1.6
1.7 dia.
28°±4°
Marking Side
2.54
2.54 7
0.2 0.45
(6)
(4)
(6)
(4)
(5)
(3)
(1)
(2)
(3)
(1)
(2)
0.3
2.54
Single Pole Type Double Pole Type
(6)
(4)
(5)
(3)
(1)
(2)
(3)
(1)
(2)
1.7 dia.
28°±4°
Marking Side
1.6 (5.6)
11
3.8
0.45
0.2
2.54
2.54 7
0.3
3.1
2.6
2.54
5.08
Single Pole Type Double Pole Type
(6)
(4)
(5)
(3)
(1)
(2)
(3)
(1)
(2)
11
28°
±4°
3.8
1.6 (5.6)
1.7 dia.
Marking Side
5.08
7
0.45
2.54
2.54
2.54
0.3
Single Pole Type Double Pole Type
3
A9TSA9TS
■PCB Dimensions (Top View)
DIP Terminal Models Right Angle Terminal Models
Vertical Mount Terminal Models
■Switching Function / Internal Connections
Note: Lever do not stop at "−" position.
Single Pole Type Double Pole Type
2.54
5.08
(1)
(2)
(3)
(4)
(6)
Five-0.6 dia.
+0.1
0
2.54
5.08
Six-0.6 dia.
+0.1
0
(1)
(2)
(3)
(4)
(5)
(6)
Single Pole Type Double Pole Type
5.08
5.08
(3)
(2)
(1)
Five-0.6 dia.
+0.1
0
5.082.54
5.08
(3)
(2)
(1)
(6)
(5)
(4)
Eight-0.6 dia.
+0.1
0
Single Pole Type Double Pole Type
Switching Functions
SPDT Models
ON −ON
ON OFF ON
DPDT Models
ON −ON
ON OFF ON
5.08
5.08
(1)
(2)
(3)
Five-0.6 dia.
+0.1
0
2.54
5.08
5.08
(4)
(5)
(6)
(1)
(2)
(3)
Eight-0.6 dia.
+0.1
0
2.54
23
1
2
1
3
2
1
3
23
1
56
4
23
1
56
4
23
1
5
6
4
A9TSA9TS
■Safety Precautions
Be sure to read the Safety precautions common to all PCB-mount Manual Switch for correct use.
●Cautions
Use the switch within the rated voltage and current ranges,
otherwise the Switch may have a shortened life expectancy,
radiate heat,or burn out. This particularly applies to the
instantaneous voltages and currents when switching.
●Hardling
Do not apply excessive operating force to the Switch. Otherwise
the Switch may be damaged or deformed, and the switch
mechanism may malfunction as a result. Apply an operating force
not exceeding 9.8N {1,000gf}. Apply the operating load from the
top of the actuator. Do not apply a load from angle or from side
the actuator. Doing so may deform the Switch contact.
●Soldering
Observe the following conditions when soldering the Switch.
Automatic Soldering Bath
Soldering temperature: 260
°
C max. (Preheating: 100
°
C 120s max.)
Soldering time: 5s max.
Manual Soldering
Soldering temperature: 350 °C at the tip of the soldering iron.
Soldering time: 3s max.
●Washing
Apply alcohol based solvents to clean.
Do not clean the Switch immediately after soldering. Wait for at
least five minutes after soldering before cleaning.
Ultrasonic cleaning is not available dip into Switch washing
agents for two minutes maximum.
●Using Flux
Making mistakes in the type of flux or in the amount or method in
which it is applied can cause flux to enter the interior of the
Switch, with adverse effects on Switch performance. Assess the
proper flux, conditions,and methods prior to using it.
●RoHS Compliant
The "RoHS Compliant" designation indicates that the listed
models do not contain the six hazardous substances covered by
the RoHS Directive.
Reference: The following standards are used to determine
compliance for the six substances.
• Lead: 1,000 ppm max.
• Mercury: 1,000 ppm max.
• Cadmium: 100 ppm max.
• Hexavalent chromium: 1,000 ppm max.
• PBB: 1,000 ppm max.
• PBDF: 1,000 ppm max.
●Environment for Storage and Use
To prevent discoloration of the terminals and other problems
during storage, do not store the Switch in locations subject to the
following conditions.
1. High temperature or humidity
2. Corrosive gases
3. Direct sunlight
Also, the Switch is not waterproof or splash-resistance.
Do not use the Switch in locations that are subject to contact with
water. Do not subject the Switch to freezing or condensation.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Omron:
A9TS12-0013 A9TS11-0011 A9TS11-0013 A9TS12-0011 A9TS12-0012 A9TS21-0012 A9TS21-0013 A9TS22-
0011 A9TS22-0012 A9TS22-0013 A9TS21-0011 A9TS11-0012