HAS30 DC-DC Series Data Sheet Features * * * * * * * * Industry standard half-brick Low-cost design 100C baseplate operation Open-frame packaging 24V and 48V input versions Input Pi filter Optional enable logic 1500V isolation Description HAS dc-dc converters provide up to 30 watts of output power in an industry-standard package and footprint. With a maximum case temperature of 100C, the HAS is well suited for the most demanding telecom, networking, and industrial applications. The HAS features 1500 VDC isolation, short circuit, and overtemperature protection, as well as six-sided shielding. The HAS series is available with optional enable and voltage trim pins. Please see the HAD Series for dual-output applications. Efficiency vs. Load (24V Input) Technical Specifications Input 90 18 - 36 VDC 36 - 75 VDC 100V/100ms 50 mA 85 EFFICIENCY % Voltage Range 24 VDC Nominal 48 VDC Nominal Transient Reflected Ripple 80 HAS030YG-A 75 EFF. (18v) EFF. (24v) 70 EFF. (36v) Output 1% 0.2% Vout 0.2% Vout 0.5 VDC 10 % 25% Iout 4% Vout 500 s 10% Hiccup 110 - 140% 115 - 140% Vout Nom. Vin Negative 10 mA Max. 60 10 20 30 40 50 60 70 80 90 100 90 100 LOAD % Efficiency vs. Load (48V Input) 95 90 85 EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Remote Sense Headroom Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Short Circuit / Overcurrent Protection Current Limit Threshold Range, % of Iout Rated OVP Trip Range Remote Shutdown Reference Shutdown Pin Current, Sourced At Off 65 80 75 70 HAS030ZH-A 65 HAS030ZG-A 60 HAS030ZJ-A 55 50 General Turn-On Time Remote Shutdown Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 Min Each MTBF (Bellcore TR-NWT-000332) Safety Weight (Approx.) 10 10 ms Positive/Negative Logic 250 kHz 1500 VDC 1050 VDC 500 VDC 0.03%/C -40 To +100C -40 To +125C 95% 5 g, 10 - 55 Hz 2.5 X 106 hrs UL, cUL, TUV 1.4 oz REV. JUN 03, 2004 Page 1 of 3 20 30 40 50 60 70 80 LOAD % Notes MTBF predictions may vary slightly from model to model. Specifications typically at 25C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. HAS30 DC-DC Series Data Sheet Model Selection MODEL INPUT VOLTAGE (VOLTS) INPUT VOLTAGE RANGE (VOLTS) MAXIMUM INPUT CURRENT (AMPS)* OUTPUT VOLTAGE (VOLTS) RATED OUTPUT CURRENT (AMPS) 24 24 24 48 48 48 48 18-36 18-36 18-36 36-75 36-75 36-75 36-75 2.2 2.2 2.2 1.0 1.3 1.3 1.3 5 12 15 3.3 5 12 15 6.0 2.5 2.0 6.0 6.0 2.5 2.0 HAS030YG-A HAS030YH-A HAS030YJ-A HAS030ZE-AT HAS030ZG-A HAS030ZH-A HAS030ZJ-A RIPPLE & NOISE pk-pk (mV) TYPICAL EFFICIENCY** 100 150 150 100 100 150 150 83% 87% 86% 81% 83% 88% 88% NOTES: * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. Model numbers highlighted in yellow or shaded are not recommended for new designs. Mechanical Drawing MOUNTING INSERTS M3X.5 THROUGH 4PL 2.28" (57.9mm) 0.18" (4.6mm) 1.700"(43.2mm) 1.400"(35.6mm) 1 5 1.400"(35.6mm) 1.000"(25.4mm) 2 6 1.000"(25.4mm) 7 0.700"(17.8mm) 0.400"(10.2mm) BOTTOM VIEW 0.400"(10.2mm) 3 8 0 4 9 DIA 0.040" (1.0mm) 2.40" (61.0mm) 0 -0.300"(-7.6mm) -0.300"(-7.6mm) -0.50"(-12.7mm) -0.19" (-4.8mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 7.9 C/W 6.8 C/W 4.9 C/W 3.6 C/W 3.0 C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. 0 0.025" REF. (0.6mm) 1.900" (48.3mm) Pin 0.50" (12.7mm) Tolerances Function 1 -Vin 2 3 4 Case On/Off +Vin 5 -Vout 6 7 8 9 -Sense Trim +Sense +Vout REV. JUN 03, 2004 Page 2 of 3 Inches: .XX 0.020 .XXX 0.010 Pin: 0.002 (Millimeters) .X 0.5 .XX 0.25 0.05 (Dimensions as listed unless otherwise specified.) OPTIONS This page is offered as a reference. Consult factory for actual availability of options. When ordering equipment options, use the following suffix information. Select preferred option(s) and add the suffix to the model number. Ordering option examples are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, HLS, HLD, LES, QBS, QES, QLS, TES, TQD Lucent-Compatible Trim T HAS, HBD, HBS, HES, HLS, QBS, QES, QLS Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES 0.110" (2.8mm) Pin Length 8 All Leaded Models 0.150" (3.8mm) Pin Length 9 All Leaded Models Pin Length and Heatsink Options REMARKS TTL "Low" Turns Module ON TTL "High" Turns Module OFF Standard Pin Length is 0.180" (4.6mm) 0.24" (6.1mm) Horizontal Heatsink 1H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.24" (6.1mm) Vertical Heatsink 1V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.45" (11.4mm) Horizontal Heatsink 2H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.45" (11.4mm) Vertical Heatsink 2V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.95" (24.1mm) Horizontal Heatsink 3H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad 0.95" (24.1mm) Vertical Heatsink 3V All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks (Except HLS, HLD, QLS, TLD, and TKD Packages) Includes Thermal Pad Example Options: HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95" vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110" pin length. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. REV. JUN 03, 2004 Page 3 of 3