1/5
47000 SERIES - ELECTRONIC TRANSFORMERS
MYRRA encapsulated electronic transformers are
Switched Mode Power Supplies based on Flyback
topology.
They constitute an interesting alternative to the
traditional supply in the most common
applications of power lower than 5W.
ENERGY SAVING due to high efficiency and low
standby power
The applications for the Electronic serie are:
o Alternative to the linear transformers in all
AC/DC applications of power up to than 5W
o Alternative to DC/DC converters for application
in D.C.current (Telecom supplies, electric
substations etc.)
o Industrial, domestic and consumer electronics
applications
o Standby devices and others DC or AC auxiliary
supplies
With the same footprint as a EI30 transformer, they
will replace:
- 50 Hz Transformer
- Fuse
- Bridge Rectifier
- Filtering Capacitor
Regulated types will also replace linear regulator and
heatsink
MAIN FEATURES
o Wide input voltage range
o Increased power. 3 x compared to standard
EI30 transformer
o Better energetic efficiency: 70% typical
compared to 40% for the conventional
supply
o Very low Standby Power consumption:
meets requirements of Energy Star or EC
Code of Conduct
o Same footprint as EI30 transformer :
Upgrade your application without redesign
of PCB
SAFETY STANDARDS
Meets all requirements of:
o EN 60950
o EN 60335
o EN 61558-2-17
o Uses UL listed components
o Uses UL 94-V0 plastic and resin
EMC STANDARDS
Conducted and radiated emissions conform to
o EN 55014-1
o EN 55022 class B
Immunity conform to
o EN 55014-2
o EN 61000-4-x
Downloaded from Elcodis.com electronic components distributor
2/5
47000 SERIES - ELECTRONIC TRANSFORMERS
ONE OUTPUT 2.5 & 5W - Regulated
ELECTRICAL SPECIFICATIONS
Input voltage range
85 to 265 Volts AC
85 to 370 Volts DC
Input Frequency 47 to 440 Hz
Output voltage accuracy (full load ) ± 2%
Line output voltage variation ± 0.3%
Load output voltage variation ± 0.5%
No load input power < 200mW
Energy consumption and efficiency :
Meets requirements of Energy Star and
EC Code of Conduct
SAFETY
Prepared for Class II – reinforced insulation
Input / Output Isolation test voltage: 4000 Vac
Operating ambient temperature:
- 25°C / + Ta (See table)
Storage temperature: - 40°C / + 85°C
Input protection by integrated fusible resistor
Output short circuit protection: automatic restarts
when fault condition is removed
Thermal shutdown with automatic recovery if internal
temperature exceeds allowable value
Reference
Output voltage
(DC Volts)
Output current
(DC mA)
Output Power
(W)
Efficiency
(%)
Ta
(°C)
47121
3.3
750
2.5
65
+70
47122
5
550
2.75
68
+70
47123
9
270
2.5
72
+70
47124
12
210
2.5
74
+70
47125
15
170
2.5
75
+70
47126
24
110
2.5
77
+70
47151
3.3
1350
4.2
65
+50
47152
5
900
4.5
68
+50
47153
9
550
5
72
+50
47154
12
420
5
75
+50
47155
15
320
5
76
+50
47156
24
220
5
79
+50
DIMENSIONS and PINOUT
4 pins
pins 1 & 5 : AC or DC Input
pin 7: DC output +V
pin 9: DC output 0V
(view from pins side):
Downloaded from Elcodis.com electronic components distributor
3/5
47000 SERIES - ELECTRONIC TRANSFORMERS
ONE OUTPUT 3.2 & 5W Non Regulated
ELECTRICAL SPECIFICATIONS
Input voltage range
85 to 265 Volts AC
85 to 370 Volts DC
Input Frequency 47 to 440 Hz
Output voltage accuracy (full load) ± 5%
Line output voltage variation ± 3%
Load output voltage variation 0/ +30%
No load input power < 300mW
SAFETY
Prepared for Class II – reinforced insulation
Input / Output Isolation test voltage: 4000 Vac
Operating ambient temperature:
- 25°C / + Ta (See table)
Storage temperature: - 40°C / + 85°C
Input protection by integrated fusible resistor
Output short circuit protection: automatic restarts
when fault condition is removed
Thermal shutdown with automatic recovery if internal
temperature exceeds allowable value
Reference
(DC Volts)
Output current
(DC mA)
Output Power
(W)
Efficiency
(%)
Ta
(°C)
47114
12
200
2.4
74
+70
47133
9
360
3.2
73
+70
47134
12
270
3.2
75
+70
47136
24
130
3.2
80
+70
47163
9
560
5 *
73
+50
47164
12
420
5 *
75
+50
47166
24
210
5 *
80
+50
* Nota: Power up to 5.4W is possible with input voltage ≥ 97 Vac
DIMENSIONS and PINOUT
4 pins
pins 1 & 5 : AC or DC Input
pin 7: DC output +V
pin 9: DC output 0V
(view from pins side):
Downloaded from Elcodis.com electronic components distributor
4/5
47000 SERIES - ELECTRONIC TRANSFORMERS
TWO COMMON OUTPUTS 3 to 5W - Regulated
ELECTRICAL SPECIFICATIONS
Input voltage range
85 to 265Volts AC
85 to 370V DC
Input Frequency 47 to 440 Hz
Output voltage accuracy : see table for 10 to 100%
rated load of each output (includes line and load
variations)
No load input power < 200mW
Energy consumption and efficiency : Meets
requirements of Energy Star or EC Code of Conduct
The 2 outputs share a common 0v reference.
This enables closer coupling and a better cross-
regulation of the outputs
SAFETY
Prepared for Class II – reinforced insulation
Input / Output Isolation test voltage: 4000 Vac
Operating ambient temperature:
- 25°C / + Ta (See table)
Storage temperature: - 40°C / + 85°C
Input protection by integrated fusible resistor
Output short circuit protection: automatic restarts
when fault condition is removed
Thermal shutdown with automatic recovery if internal
temperature exceeds allowable value
Reference
Output 1
Output 2
(DC Volts)
Output 1
Output 2
(DC mA)
Output 1
Output 2
accuracy
Efficiency (%)
Ta
(°C)
47243
+10.5
+7
380 max
100 max
± 3%
± 15%
72
+60
47244
+15
+7
300 max
70 max
± 3%
± 15%
73
+60
47245
+12
+5.5
130 max
300 max
± 5%
± 10%
65
+70
47246
+5
+12
400 (600max)
170 max
± 3%
± 15%
65
+60
47247
+15
-15
130 max
130 max
± 8%
± 8%
73
+60
* Nota: Power up to 5W is possible with input voltage ≥ 97 Vac and Ta ≤ 50°C
DIMENSIONS and PINOUT
5 pins
pins 1 & 5 : AC or DC Input
pin 6: Common output 0V
pin 7: DC output 1
pin 10: DC output 2
(view from pins side):
Downloaded from Elcodis.com electronic components distributor
5/5
47000 SERIES - ELECTRONIC TRANSFORMERS
TWO ISOLATED OUTPUTS 3 to 5W - Regulated
ELECTRICAL SPECIFICATIONS
Input voltage range
85 to 265Volts AC
85 to 370V DC
Input Frequency 47 to 440 Hz
Output voltage accuracy : see table for 10 to 100%
rated load of each output (includes line and load
variations)
No load input power < 200mW
Energy consumption and efficiency :
Meets requirements of Energy Star or EC Code of
Conduct
2 isolated outputs - Output 1 only is regulated and
should provide the higher power
SAFETY
Prepared for Class II – reinforced insulation
Input / Output Isolation test voltage: 4000 Vac
Output1 / Output 2 isolation : 4000Vac
Operating ambient temperature:
- 25°C / + Ta (See table)
Storage temperature: - 40°C / + 85°C
Input protection by integrated fusible resistor
Output short circuit protection: automatic restarts
when fault condition is removed
Thermal shutdown with automatic recovery if internal
temperature exceeds allowable value
Reference
Output 1
Output 2
(DC Volts)
Output 1
Output 2
(DC mA)
Output Power
(max W)
Output 1
Output 2
accuracy
Efficiency (%)
Ta
(°C)
47252
5
5
350 (600max)
350 max
3.5
± 3%
± 15%
66
+60
47254
12
12
165 (300max)
165 max
4
± 5%
± 15%
72
+60
47255
15
15
135 (200max)
135 max
4
± 5%
± 15%
73
+60
47257
5
12
400 (600max)
170 max
4
± 3%
± 15%
68
+60
47258
18
8
150 (200max)
150 max
4
± 5%
± 15%
72
+60
DIMENSIONS and PINOUT
6 pins
pins 1 & 5 : AC or DC Input
pin 6: DC output1 0V
pin 7: DC output1 +V
pin 9: DC output2 0V
pin 10: DC output2 +V
(view from pins side):
Downloaded from Elcodis.com electronic components distributor