CYW20735 Single-Chip Bluetooth Transceiver for Wireless Input Devices The Cypress CYW20735 is a Bluetooth 5.0-compliant, stand-alone baseband processor with an integrated 2.4 GHz transceiver. Manufactured using the industry's advanced 40 nm CMOS low-power process, the CYW20735 employs high levels of integration to minimize external components, reducing the device footprint and the costs associated with implementing Bluetooth solutions. The CYW20735 is the optimal solution for applications in wireless input devices including game controllers, remote controls, keyboards, and joysticks. Built-in firmware adheres to the Bluetooth Low Energy (BLE) profile and the BLE Human Interface Device (HID) profile. Cypress Part Numbering Scheme Cypress is converting the acquired IoT part numbers from Cypress to the Cypress part numbering scheme. Due to this conversion, there is no change in form, fit, or function as a result of offering the device with Cypress part number marking. The table provides Cypress ordering part number that matches an existing IoT part number. Table 1. Mapping Table for Part Number between Broadcom and Cypress Broadcom Part Number Cypress Part Number BCM20735 CYW20735 BCM20735PKML1G CYW20735PKML1G Features Complies with Bluetooth Core Specification version 5.0 with LE 2 Mbps Programmable key scan matrix interface, up to 8 x 20 keyscanning matrix Supports Basic Rate (BR) and Bluetooth Low Energy (BLE) Three-axis quadrature signal decoder BLE HID profile version 1.00 compliant Infrared modulator Bluetooth Device ID profile version 1.3 compliant IR learning Supports Generic Access Profile (GAP) Auxiliary ADC with up to 28 analog channels Supports Adaptive Frequency Hopping (AFH) Excellent receiver sensitivity On-chip support for serial peripheral interface (SPI) (master and slave modes) Programmable output power control Integrated ARM Cortex-M4 microprocessor core floating point unit (FPU) Cypress Serial Communications (BSC) interface (compatible with NXP I2C slaves) LE packet extension On-chip power-on reset (POR) Timed wakeup Support for serial flash devices Wireless charging interface Integrated buck and low dropout (LDO) regulators Package types: On-chip software controlled power management unit 60-pin quad flat no-lead (QFN) RoHS compliant Applications Game controllers 3D glasses Wireless pointing devices (mice) Blood pressure monitors Remote controls Find-me devices Wireless keyboards Heart-rate monitors Joysticks Proximity sensors Home automation Thermometers Point-of-sale input devices Cypress Semiconductor Corporation Document Number: 002-14881 Rev. *H * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised Wednesday, April 18, 2018 CYW20735 Figure 1. Functional Block Diagram RF MODEM I2C Master JTAP I2C Slave SPIFFY Random Number UART MIPI DBI-C UART PCM (I2S) SPI Slave AHB Master Debug UART SPIFFY Dual SPI Quad SPI SW Debug PKA AES TX/RX DDT SHA JTAG Master ARM SMDMAC ARM CM4/FPU PTU Main RX TX CRC CRC Filter CSMACA Decoder BlueRF BT RF Scheduler 2 PCM2 (I S) BLE RX/TX Security Engine BIST Symbol Counter PTU Aux LCU MAC154_TOP GCI BPL AHB Bus Matrix (12/24/48/96 MHz) Patch Control ROM 2MB MTU BT Audio AHB2APB Patch RAM 64KB RAM 320KB OTP 2KB CLB_UPI_MISC CLB_UPI_PMU PWM MIA_KQD Programmable Wait States Watch Dog TRIAC KYS IR IRL MIF (Quad) ADC Control Timer Thick Oxide Retention RAM Analog PMU 16KB Bermuda PDS Cap Touch 3D Glass AVS SPM GPIO Power Domain Digital PMU Sleep Timer DWP Programmable Wait States for LHL LPO Timer VDDC Pause LPO Calibration VDDCG Level Shifter Level Shifter OTP AHB Master VBAT Legend Panama Power Switch HID OFF Timer Wakeup KYS/QUAD/GPIO/Timer HP-LPO 128KHz XTALOSC 32KHz LP-LPO 16/32/128KHz AUX ADC LHL_LSP_PAD GPIO * 40 + IR Power/Ground LHL_TOP Document Number: 002-14881 Rev. *H RSTN JTAG_SEL LHL_PAD Page 2 of 51 CYW20735 Contents 1. Functional Description ................................................. 4 1.1 Bluetooth Baseband Core ..................................... 4 1.2 Microprocessor Unit .............................................. 6 1.3 Power Management Unit ....................................... 8 1.4 Integrated Radio Transceiver ................................ 8 1.5 Peripheral Transport Unit ...................................... 9 1.6 UART Interface .................................................... 10 1.7 Peripheral UART Interface .................................. 10 1.8 Clock Frequencies ............................................... 11 1.9 GPIO Ports .......................................................... 12 1.10 Keyboard Scanner ............................................. 13 1.11 Mouse Quadrature Signal Decoder ................... 14 1.12 ADC Port ........................................................... 14 1.13 PWM .................................................................. 15 1.14 Triac Control ...................................................... 15 1.15 Serial Peripheral Interface ................................. 15 1.16 Infrared Modulator ............................................. 16 1.17 Infrared Learning ............................................... 16 1.18 PDM Microphone ............................................... 16 Document Number: 002-14881 Rev. *H 1.19 Security Engine ................................................. 17 1.20 Power Management Unit ................................... 17 2. Pin Assignments and GPIOs ..................................... 18 2.1 Pin Assignments .................................................. 18 2.2 GPIO Pin Descriptions ........................................ 21 2.3 Ball Maps ............................................................. 30 3. Specifications ............................................................. 31 3.1 Electrical Characteristics ..................................... 31 3.4 Timing and AC Characteristics ............................ 41 4. Mechanical Information ............................................. 47 4.1 Package Diagrams .............................................. 47 4.2 Tray Packaging Specifications ............................ 48 5. Ordering Information .................................................. 49 6. Additional Information ............................................... 49 6.1 IoT Resources ..................................................... 49 6.2 Acronyms and Abbreviations ............................... 49 Document History Page ................................................ 51 Sales, Solutions, and Legal Information ..................... 52 Page 3 of 51 CYW20735 1. Bluetooth Baseband Core The Bluetooth Baseband Core (BBC) implements all of the time-critical functions required for high-performance Bluetooth operation. The BBC manages the buffering, segmentation, and routing of data for all connections. It also buffers data that passes through it, handles data flow control, schedules ACL and TX/RX transactions, monitors Bluetooth slot usage, optimally segments and packages data into baseband packets, manages connection status indicators, and composes and decodes HCI packets. In addition to these functions, it independently handles HCI event types, and HCI command types. Table 2. Bluetooth Features Bluetooth 1.0 Basic Rate Bluetooth 1.2 Bluetooth 2.0 Interlaced Scans - - Adaptive Frequency Hopping - Paging and Inquiry - - Page and Inquiry Scan - - Sniff - - Bluetooth 2.1 Bluetooth 3.0 Bluetooth 4.0 Secure Simple Pairing Unicast Connectionless Data Bluetooth Low Energy Enhanced Inquiry Response Enhanced Power Control - Sniff Subrating - - Bluetooth 4.1 Bluetooth 4.2 Low Duty Cycle Advertising Data Packet Length Extension Dual Mode LE Secure Connection LE Link Layer Topology Link Layer Privacy 1.1 Link Control Layer The link control layer is part of the Bluetooth link control functions that are implemented in dedicated logic in the link control unit (LCU). This layer consists of the command controller that takes commands from the software, and other controllers that are activated or configured by the command controller, to perform the link control tasks. Each task is performed in a different state or substate in the Bluetooth Link Controller. BLE states: Advertising Scanning Connection Major states: Standby Connection Substates: Page Page Scan Inquiry Inquiry Scan Sniff Document Number: 002-14881 Rev. *H Page 4 of 51 CYW20735 1.2 Test Mode Support The CYW20735 fully supports Bluetooth Test mode as described in Part I:1 of the Specification of the Bluetooth System Version 3.0. This includes the transmitter tests, normal and delayed loopback tests, and reduced hopping sequence. In addition to the standard Bluetooth Test Mode, the CYW20735 also supports enhanced testing features to simplify RF debugging and qualification and type-approval testing. These features include: Fixed frequency carrier wave (unmodulated) transmission Simplifies some type-approval measurements (Japan) Aids in transmitter performance analysis Fixed frequency constant receiver mode Receiver output directed to I/O pin Allows for direct BER measurements using standard RF test equipment Facilitates spurious emissions testing for receive mode Fixed frequency constant transmission 8-bit fixed pattern or PRBS-9 Enables modulated signal measurements with standard RF test equipment 1.3 Frequency Hopping Generator The frequency hopping sequence generator selects the correct hopping channel number based on the link controller state, Bluetooth clock, and device address. Document Number: 002-14881 Rev. *H Page 5 of 51 CYW20735 1.4 Microprocessor Unit The CYW20735 microprocessor unit runs software from the link control (LC) layer up to the host controller interface (HCI). The microprocessor is a Cortex-M4 32-bit RISC processor with embedded ICE-RT debug and serial wire debug (SWD) interface units. The microprocessor also includes 2 MB of ROM memory for program storage and 384 KB of RAM for data scratch-pad. The internal ROM provides flexibility during power-on reset to enable the same device to be used in various configurations. At powerup, the lower-layer protocol stack is executed from internal ROM. External patches can be applied to the ROM-based firmware to provide flexibility for bug fixes and feature additions. The device also supports the integration of user applications and profiles. 1.4.1 Floating Point Unit CYW20735 includes the CM4 single precision IEEE-754 compliant floating point unit. For details see the Cortex-M4 manual. 1.4.2 OTP Memory The CYW20735 includes 2 KB of one-time programmable memory that can be used by the factory to store product-specific information. Note: Use of OTP requires that a 3V supply be present at all times. 1.4.3 NVRAM Configuration Data and Storage NVRAM contains configuration information about the customer application, including the following: Fractional-N information BD_ADDR UART baud rate SDP service record File system information used for code, code patches, or data. The CYW20735 uses SPI flash for NVRAM storage. 1.4.4 Power-On Reset The CYW20735 includes POR logic to allow the part to initialize correctly when power is applied. Figure 2 shows the sequence used by the CYW20735 during initialization. An small external cap may be used on RESET_N to add delay as VDDIO ramps up. Document Number: 002-14881 Rev. *H Page 6 of 51 CYW20735 1.4.5 External Reset An external active-low reset signal, RESET_N, can be used to put the CYW20735 in the reset state. Figure 2. Power-On Reset Timing RESET_N (External) >= 2.4 ms (*1) VDDIO ~190 us (*2) VDDC ~2 LPO cycles VDDIO POR 8 LPO cycles VDDC Reset (Internal) XTAL_PU ~2 LPO cycles ~30 LPO cycles XTAL_BUF_PU *1: External RESET_N is only effective 2.4 ms after VDDIO power is up *2: The latency depends on the value of DEFAULT_STRAP. If DEFAULT_STRAP is high, it's ~190 us. If DEFAULT_STRAP is low, it's ~250 us. 1.4.6 Brownout Detection An external voltage detector reset IC may be used if brownout detection is required. The reset IC should release RESET_N only after the VDDO supply voltage level has been at or above a minimum operating voltage for 50 ms or longer. Document Number: 002-14881 Rev. *H Page 7 of 51 CYW20735 1.5 Power Management Unit Figure 3 shows the CYW20735 power management unit (PMU) block diagram. The CYW20735 includes an integrated buck regulator, a capless LDO, PALDO and an additional 1.2V LDO for RF. Figure 3. Power Management Unit PMU CBUCK SR_VDDBAT3V 50 mA SR_VLX SR_VBF DIGLDO DIGLDO_VDDIN1P5 RFLDO_VDDIN1P5 (Capless, with bypass mode) 30 mA RFLDO 20 mA DIGLDO_VDDOUT o_vddout_digldo RFLDO_VDDOUT PMU_AVSS PALDO PALDO_VDDIN_5V NOTE: Document Number: 002-14881 Rev. *H PALDO_VDDOUT3V = Bump/Ball Page 8 of 51 CYW20735 1.6 Integrated Radio Transceiver The CYW20735 has an integrated radio transceiver that has been optimized for use in 2.4 GHz Bluetooth wireless systems. It has been designed to provide low-power, low-cost, robust communications for applications operating in the globally available 2.4 GHz unlicensed ISM band. The CYW20735 is fully compliant with the Bluetooth Radio Specification and meets or exceeds the requirements to provide the highest communication link quality of service. 1.6.1 Transmit Path The CYW20735 features a fully integrated transmitter. The baseband transmit data is GFSK modulated in the 2.4 GHz ISM band. 1.6.2 Digital Modulator The digital modulator performs the data modulation and filtering required for the GFSK signal. The fully digital modulator minimizes any frequency drift or anomalies in the modulation characteristics of the transmitted signal. 1.6.3 Power Amplifier The CYW20735 has an integrated power amplifier (PA) that can transmit up to +10 dBm for class 1 operations. 1.6.4 Receiver Path The receiver path uses a low-IF scheme to downconvert the received signal for demodulation in the digital demodulator and bit synchronizer. The receiver path provides a high degree of linearity, an extended dynamic range to ensure reliable operation in the noisy 2.4 GHz ISM band. The front-end topology, with built-in out-of-band attenuation, enables the CYW20735 to be used in most applications with minimal off-chip filtering. 1.6.5 Digital Demodulator and Bit Synchronizer The digital demodulator and bit synchronizer takes the low-IF received signal and performs an optimal frequency tracking and bitsynchronization algorithm. 1.6.6 Receiver Signal Strength Indicator The radio portion of the CYW20735 provides a receiver signal strength indicator (RSSI) signal to the baseband, so that the controller can take part in a Bluetooth power-controlled link by providing a metric of its own receiver signal strength to determine whether the transmitter should increase or decrease its output power. 1.6.7 Local Oscillator A local oscillator (LO) generation provides fast frequency hopping (1600 hops/second) across the 79 maximum available channels. The CYW20735 uses an internal loop filter. 1.6.8 Calibration The CYW20735 radio transceiver features a self-contained automated calibration scheme. No user interaction is required during normal operation or during manufacturing to provide optimal performance. Calibration compensates for filter, matching network, and amplifier gain and phase characteristics to yield radio performance within 2% of what is optimal. Calibration takes process and temperature variations into account, and it occurs transparently during normal operation and hop setting times. Document Number: 002-14881 Rev. *H Page 9 of 51 CYW20735 1.7 Peripheral Transport Unit 1.7.1 I2C Compatible Master The CYW20735 provides a 2-pin master I2C to communicate with peripherals such as trackball or touch-pad modules, and motion tracking ICs used in mouse devices. The BSC interface is compatible with I2C slave devices. I2C does not support multimaster capability or flexible wait-state insertion by either master or slave devices. The following transfer clock rates are supported by I2C: 100 kHz 400 kHz 800 kHz (Not a standard I2C-compatible speed.) 1 MHz (Compatibility with high-speed I2C-compatible devices is not guaranteed.) The following transfer types are supported by BSC: Read (Up to 8 bytes can be read.) Write (Up to 8 bytes can be written.) Read-then-Write (Up to 8 bytes can be read and up to 8 bytes can be written.) Write-then-Read (Up to 8 bytes can be written and up to 8 bytes can be read.) Hardware controls the transfers, requiring minimal firmware setup and supervision. The clock pin (SCL) and data pin (SDA) are both open-drain I/O pins. Pull-up resistors external to the CYW20735 are required on both the SCL and SDA pins for proper operation. 1.7.2 HCI UART Interface The CYW20735 includes a UART interface for factory programming and when operating as a BT HCI device in a system with an external host. The UART physical interface is a standard, 4-wire interface (RX, TX, RTS, and CTS) with adjustable baud rates from 57600 bps to 6 Mbps. During initial boot, UART speeds may be limited to 750 kbps. The baud rate may be selected via a vendorspecific UART HCI command. The CYW20735 has a 1040-byte receive FIFO and a 1040-byte transmit FIFO to support enhanced data rates. The interface supports the Bluetooth UART HCI (H4) specification. The default baud rate for H4 is 115.2 kbaud. The UART clock default setting is 24 MHz, and can be configured to run as high as 48 MHz to support up to 6 Mbps. The baud rate of the CYW20735 UART is controlled by two values. The first is a UART clock divisor (set in the DLBR register) that divides the UART clock by an integer multiple of 16. The second is a baud rate adjustment (set in the DHBR register) that is used to specify a number of UART clock cycles to stuff in the first or second half of each bit time. Up to eight UART cycles can be inserted into the first half of each bit time, and up to eight UART clock cycles can be inserted into the end of each bit time. Table 2 on page 10 contains example values to generate common baud rates with a 24 MHz UART clock. Table 2. Common Baud Rate Examples, 24 MHz Clock Baud Rate (bps) Baud Rate Adjustment High Nibble Low Nibble Mode Error (%) 3M 0xFF 0xF8 High rate 0.00 2M 0XFF 0XF4 High rate 0.00 1M 0X44 0XFF Normal 0.00 921600 0x05 0x05 Normal 0.16 460800 0x02 0x02 Normal 0.16 230400 0x04 0x04 Normal 0.16 115200 0x00 0x00 Normal 0.16 57600 0x00 0x00 Normal 0.16 Document Number: 002-14881 Rev. *H Page 10 of 51 CYW20735 Table 3 contains example values to generate common baud rates with a 48 MHz UART clock. Table 3. Common Baud Rate Examples, 48 MHz Clock Baud Rate (bps) High Rate Low Rate Mode Error (%) 6M 0xFF 0xF8 High rate 0 4M 0xFF 0xF4 High rate 0 3M 0x0 0xFF Normal 0 2M 0x44 0xFF Normal 0 1.5M 0x0 0xFE Normal 0 1M 0x0 0xFD Normal 0 921600 0x22 0xFD Normal 0.16 230400 0x0 0xF3 Normal 0.16 115200 0x1 0xE6 Normal -0.08 57600 0x1 0xCC Normal 0.04 Support for changing the baud rate during normal HCI UART operation is included through a vendor-specific command that allows the host to adjust the contents of the baud rate registers. The CYW20735 UART operates correctly with the host UART as long as the combined baud rate error of the two devices is within 5%. 1.8 Peripheral UART Interface The CYW20735 has a second UART that may be used to interface to peripherals. This peripheral UART is accessed through the optional I/O ports, which can be configured individually and separately for each functional pin. The CYW20735 can map the peripheral UART to any LHL GPIO. The peripheral UART clock is fixed at 24 MHz. Both TX and RX have a 256-byte FIFO (see Table 2: "Common Baud Rate Examples, 24 MHz Clock," on page 11). Document Number: 002-14881 Rev. *H Page 11 of 51 CYW20735 1.9 Clock Frequencies The CYW20735 uses a 24 MHz crystal oscillator (XTAL). 1.9.1 Crystal Oscillator The XTAL must have an accuracy of 20 ppm as defined by the Bluetooth specification. Two external load capacitors in the range of 5 pF to 30 pF are required to work with the crystal oscillator. The selection of the load capacitors is XTAL-dependent (see Figure 4). Figure 4. Recommended Oscillator Configuration--12 pF Load Crystal 22 pF XIN Crystal XOUT 20 pF Table 4 shows the recommended crystal specifications. Table 4. Reference Crystal Electrical Specifications Parameter Nominal frequency Oscillation mode Frequency tolerance Conditions Minimum Typical Maximum Unit - 20 24 40 MHz - ppm - Fundamental - @25C - 10 Tolerance stability over temp @0C to +70C - 10 - ppm Equivalent series resistance - - - 60 Load capacitance - - 12 - pF Operating temperature range - 0 - +70 C Storage temperature range - -40 - +125 C Drive level - - - 200 W Aging - - 3 10 ppm/year Shunt capacitance - - - 2 pF 1.9.2 HID Peripheral Block The peripheral blocks of the CYW20735 all run from a single 128 kHz low-power RC oscillator. The oscillator can be turned on at the request of any of the peripherals. If the peripheral is not enabled, it shall not assert its clock request line. The keyboard scanner is a special case, in that it may drop its clock request line even when enabled, and then reassert the clock request line if a keypress is detected. Document Number: 002-14881 Rev. *H Page 12 of 51 CYW20735 1.9.3 32 kHz Crystal Oscillator Figure 5 shows the 32 kHz XTAL oscillator with external components and Table on page 13 lists the oscillator's characteristics. It is a standard Pierce oscillator using a comparator with hysteresis on the output to create a single-ended digital output. The hysteresis was added to eliminate any chatter when the input is around the threshold of the comparator and is ~100 mV. This circuit can be operated with a 32 kHz or 32.768 kHz crystal oscillator or be driven with a clock input at a similar frequency. The default component values are: R1 = 10 M and C1 = C2 = ~10 pF. The values of C1 and C2 are used to fine-tune the oscillator. Figure 5. 32 kHz Oscillator Block Diagram C2 32.768 kHz XTAL R1 C1 Table 5. XTAL Oscillator Characteristics Parameter Output frequency Symbol Conditions Minimum Typical Maximum Unit Foscout - - 32.768 - kHz Frequency tolerance Start-up time - Crystal-dependent - 100 - ppm Tstartup - - - 500 ms XTAL drive level Pdrv For crystal selection 0.5 - - W XTAL series resistance Rseries For crystal selection - - 70 k XTAL shunt capacitance Cshunt For crystal selection - - 1.3 pF 1.10 GPIO Ports GPIO ports for this device is shown in Table 7 on page 22. The CYW20735 uses 40 general-purpose I/Os (GPIOs). All GPIOs support programmable pull-ups and are capable of driving up to 8 mA at 3.3V or 4 mA at 1.8V, except P26, P27, P28, and P29, which are capable of driving up to 16 mA at 3.3V or 8 mA at 1.8V. P0, P1, P8-P18, P21-23, P28-P38: all of these pins can be programmed as ADC inputs. Port 26-Port 29: all four of these pins are capable of sinking up to 16 mA for LEDs. These pins also have the PWM function, which can be used for LED dimming. Document Number: 002-14881 Rev. *H Page 13 of 51 CYW20735 1.11 Keyboard Scanner The keyboard scanner is designed to autonomously sample keys and store them into buffer registers without the need for the host microcontroller to intervene. The scanner has the following features: Ability to turn off its clock if no keys are pressed. Sequential scanning of up to 160 keys in an 8 x 20 matrix. Programmable number of columns from 1 to 20. Programmable number of rows from 1 to 8. 16-byte key code buffer (can be augmented by firmware). 128 kHz clock that allows scanning of full 160-key matrix in about 1.2 ms. N-key rollover with selective 2-key lockout if ghost is detected. Keys are buffered until host microcontroller has a chance to read it, or until overflow occurs. Hardware debouncing and noise/glitch filtering. Low-power consumption. Single-digit A-level sleep current. 1.11.1 Theory of Operation The key scan block is controlled by a state machine with the following states: 1.11.2 Idle The state machine begins in the idle state. In this state, all column outputs are driven high. If any key is pressed, a transition occurs on one of the row inputs. This transition causes the 128 kHz clock to be enabled (if it is not already enabled by another peripheral) and the state machine to enter the scan state. Also in this state, an 8-bit row-hit register and an 8-bit key-index counter is reset to 0. 1.11.3 Scan In the scan state, a row counter counts from 0 up to a programmable number of rows minus 1. After the last row is reached, the row counter is reset and the column counter is incremented. This cycle repeats until the row and column counters are both at their respective terminal count values. At that point, the state machine moves into the Scan-End state. As the keys are being scanned, the key-index counter is incremented. This counter value is compared to the modifier key codes stored in RAM, or in the key code buffer if the key is not a modifier key. It can be used by the microprocessor as an index into a lookup table of usage codes. Also, as the nth row is scanned, the row-hit register is ORed with the current 8-bit row input values if the current column contains two or more row hits. During the scan of any column, if a key is detected at the current row, and the row-hit register indicates that a hit was detected in that same row on a previous column, then a ghost condition may have occurred, and a bit in the status register is set to indicate this. 1.11.4 Scan End This state determines whether any keys were detected while in the scan state. If yes, the state machine returns to the scan state. If no, the state machine returns to the idle state, and the 128 kHz clock request signal is made inactive. Note: The microcontroller can poll the key status register. Document Number: 002-14881 Rev. *H Page 14 of 51 CYW20735 1.12 Mouse Quadrature Signal Decoder The mouse signal decoder is designed to autonomously sample two quadrature signals commonly generated by an optomechanical mouse. The decoder has the following features: Three pairs of inputs for X, Y, and Z (typical scroll wheel) axis signals. Each axis has two options: For the X axis, choose P2 or P32 as X0 and P3 or P33 as X1. For the Y axis, choose P4 or P34 as Y0 and P5 or P35 as Y1. For the Z axis, choose P6 or P36 as Z0 and P7 or P37 as Z1. Control of up to four external high-current GPIOs to power external optoelectronics: Turn-on and turn-off time can be staggered for each HC-GPIO to avoid simultaneous switching of high currents and having multiple high-current devices on at the same time. Sample time can be staggered for each axis. Sense of the control signal can be active high or active low. Control signal can be tristated for off condition or driven high or low, as appropriate. 1.12.1 Theory of Operation The mouse decoder block has four 10-bit PWMs for controlling external quadrature devices and sampling the quadrature inputs at its core. The GPIO signals may be used to control such items as LEDs, external ICs that may emulate quadrature signals, photodiodes, and photodetectors. 1.13 ADC Port The ADC block is a single switched-cap - ADC core for audio and DC measurement. It operates at the 12 MHz clock rate and has 32 DC input channels, including 28 GPIO inputs. The internal bandgap reference has 5% accuracy without calibration. Different calibration and digital correction schemes can be applied to reduce ADC absolute error and improve measurement accuracy in DC mode. Document Number: 002-14881 Rev. *H Page 15 of 51 CYW20735 1.14 PWM The CYW20735 has six internal PWMs. The PWM module consists of the following: PWM0-5. Each of the six PWM channels contains the following registers: 16-bit initial value register (read/write) 16-bit toggle register (read/write) 16-bit PWM counter value register (read) PWM configuration register shared among PWM0-5 (read/write). This 18-bit register is used: To configure each PWM channel To select the clock of each PWM channel To change the phase of each PWM channel Figure 6 shows the structure of one PWM. Figure 6. PWM Block Diagram pwm#_init_val_adr register enable o_flip clk_sel pwm_cfg_adr register pwm#_togg_val_adr register 16 16 pwm#_cntr_adr 16 cntr value is ARM readable pwm_out Example: PWM cntr w/ pwm#_init_val = 0 (dashed line) PWM cntr w/ pwm#_init_val = x (solid line) 16'HFFFF pwm_togg_val_adr 16'Hx 16'H000 pwm_out 1.15 Triac Control The CYW20735 includes hardware support for zero-crossing detection and trigger control for up to four triacs. The CYW20735 detects zero-crossing on the AC zero detection line and uses that to provide a pulse that is offset from the zero crossing. This allows the CYW20735 to be used in dimmer applications, as well as any other applications that require a control signal that is offset from an input event. The zero-crossing hardware includes an option to suppress glitches. 1.16 Serial Peripheral Interface The CYW20735 has two independent SPI interfaces, both of which support single, dual, and quad mode SPI operations. Either interface can be a master or a slave. Each interface has a 64-byte transmit buffer and a 64-byte receive buffer. To support more flexibility for user applications, the CYW20735 has optional I/O ports that can be configured individually and separately for each functional pin. The CYW20735 acts as an SPI master device that supports 1.8V or 3.3V SPI slaves. The CYW20735 can also act as an SPI slave device that supports a 1.8V or 3.3V SPI master. Note: SPI voltage depends on VDDO/VDDM; therefore, it defines the type of devices that can be supported. Document Number: 002-14881 Rev. *H Page 16 of 51 CYW20735 1.17 Infrared Modulator The CYW20735 includes hardware support for infrared TX. The hardware can transmit both modulated and unmodulated waveforms. For modulated waveforms, hardware inserts the desired carrier frequency into all IR transmissions. IR TX can be sourced from firmware-supplied descriptors, a programmable bit, or the peripheral UART transmitter. If descriptors are used, they include IR on/off state and the duration between 1-32767 sec. The CYW20735 IR TX firmware driver inserts this information in a hardware FIFO and makes sure that all descriptors are played out without a glitch due to underrun (see Figure 7). Figure 7. Infrared TX VCC R1 62 D1 INFRAREDLD CYW20735 R2 IR TX 2.4k Q1 MMBTA42 1.18 PDM Microphone The CYW20735 accepts a -based one-bit pulse density modulation (PDM) input stream and outputs filtered samples at either 8 kHz or 16 kHz sampling rates. The PDM signal derives from an external kit that can process analog microphone signals and generate digital signals. The digital signal passes through the chip IO and MUX inputs using an auxADC signal. The PDM shares the filter path with the auxADC. Two types of data rates can be supported: 8 kHz 16 kHz The external digital microphone accepts a 2.4 MHz clock generated by the CYW20735 and outputs a PDM signal which is registered by the PDM interface with either the rising or falling edge of the 2.4 MHz clock selectable through a programmable control bit. The design can accommodate two simultaneous PDM input channels, so stereo voice is possible. Document Number: 002-14881 Rev. *H Page 17 of 51 CYW20735 1.19 Security Engine The CYW20735 includes a hardware security accelerator that greatly decreases the time required to perform typical security operations. These functions include: Public key acceleration (PKA) cryptography AES-CTR/CBC-MAC/CCM acceleration SHA2 message hash and HMAC acceleration RSA encryption and decryption of modulus sizes up to 2048 bits Elliptic curve Diffie-Hellman in prime field GF(p) Generic modular math functions 1.20 Power Management Unit The Power Management Unit (PMU) provides power management features that can be invoked by software through power management registers or packet-handling in the baseband core. 1.20.1 RF Power Management The BBC generates power-down control signals for the transmit path, receive path, PLL, and power amplifier to the 2.4 GHz transceiver, which then processes the power-down functions accordingly. 1.20.2 Host Controller Power Management Power is automatically managed by the firmware based on input device activity. As a power-saving task, the firmware controls the disabling of the on-chip regulator when in HIDOFF (deep sleep) mode. 1.20.3 BBC Power Management There are several low-power operations for the BBC: Physical layer packet handling turns RF on and off dynamically within packet TX and RX. Bluetooth-specified low-power connection mode. While in these low-power connection modes, the CYW20735 runs on the Low Power Oscillator and wakes up after a predefined time period. The CYW20735 automatically adjusts its power dissipation based on user activity. The following power modes are supported: Active mode Idle mode Sleep mode HIDOFF (deep sleep) mode The CYW20735 transitions to the next lower state after a programmable period of user inactivity. When user activity resumes, the CYW20735 immediately enters Active mode. In HIDOFF mode, the CYW20735 baseband and core are powered off by disabling power to VDDC_OUT and PAVDD. The VDDO domain remains powered up and will turn the remainder of the chip on when it detects user events. This mode minimizes chip power consumption and is used for longer periods of inactivity. Document Number: 002-14881 Rev. *H Page 18 of 51 CYW20735 2. Pin Assignments and GPIOs 2.1 Pin Assignments Table 6. Pin Assignments Pin Name QFN Pin I/O Power Domain Description Microphone ADC_AVDDBAT - I ADC_AVDD ADC supply ADC_AVDDC - I ADC_AVDDC ADC supply MIC_AVDD 48 I MIC_AVDD Microphone supply MICBIAS 45 I MIC_AVDD Microphone bias supply MICN 47 I MIC_AVDD Microphone negative input MICP 46 I MIC_AVDD Microphone positive input ADC_AVSS - I AVSS Analog ground ADC_AVSSC - I AVSS Analog ground ADC_REFGND - I AVSS Analog reference ground MIC_AVSS - I AVSS Microphone analog ground BT_VDDO 36 I VDDO I/O pad power supply BT_VDDC 37 I VDDC Baseband core power supply BT_VSSC - I VSSC Digital ground LHL_VDDO 60 I VDDO LHL PAD power supply: can be tied to BT_VDDO OTP_3P3V - I BT_OTP_3P3V OTP_3P3V_ON - I VDDO Baseband Supply Power supply to the OTP: Leave floating. This pin should be connected to ground RF Power Supply BT_PAVDD2P5 26 I PAVDD2P5 PA supply BT_PLLVDD1P2 31 I PLLVDD1P2 RFPLL and crystal oscillator supply BT_VCOVDD1P2 29 I VCOVDD1P2 BT_IFVDD1P2 28 I IFVDD1P2 DIGLDO_VDDIN1P5 25 I - Internal digital LDO input and feedback pin of switching regulator (CBUCK). DIGLDO_VDDOUT - O - Internal digital LDO output RFLDO_VDDIN1P5 24 I - RF LDO input RFLDO_VDDOUT 23 O - RF LDO output PALDO_VDDIN_5V 19 I - PA LDO input PALDO_VDDOUT3V 20 O - PA LDO output SR_VDDBAT3V 22 I - Core buck input VDDBAT3V - I - Core buck input SR_VLX 21 O - Core buck output VCO supply IFPLL power supply Onboard LDOs Ground Pins SR_PVSS - I VSS PMU_AVSS - I PMU_AVSS PMU ground HS-VSS H I VSS Digital ground PALDO_AVSS - PALDO ground IF_VSS - IFPLL ground Document Number: 002-14881 Rev. *H Ground Page 19 of 51 CYW20735 Table 6. Pin Assignments (Cont.) Pin Name QFN Pin I/O Power Domain Description PAVSS - PA ground PLLVSS - RFPLL ground VCOVSS - VCO ground NC_PCB_VSS - PCB ground NC_PCB_VSS1 - PCB ground NC_PCB_VSS2 - PCB ground UART_CTS_N 44 I, PU VDDO UART_RTS_N 43 O, PU VDDO RTS for HCI UART interface. NC if unused. UART_RXD 41 I VDDO UART serial input. Serial data input for the HCI UART interface. UART_TXD 42 O, PU VDDO UART serial input. Serial data input for the HCI UART interface. SPI_MISO 40 UART CTS for HCI UART interface: NC if unused. Serial Peripheral Interface I VDDO SPI Master In Slave Out SPI_MOSI 39 O VDDO SPI Master Out Slave In SPI_CSN 38 O VDDO SPI Chip Select SPI_CLK 35 O VDDO SPI Clock Crystal BT_XTALI 32 I PLLVDD1P2 Crystal oscillator input: see "Crystal Oscillator" on page 12 for options BT_XTALO 33 O PLLVDD1P2 Crystal oscillator output XTALI_32K 50 I VDDO Low-power oscillator input XTALO_32K 49 O VDDO Low-power oscillator output Bond 0 - N/A N/A DEFAULT_STRAP 18 I VDDO Connect to VDDO BT_HOST_WAKE 34 O VDDO Host wake-up. This is a signal from the Bluetooth device to the host indicating that the Bluetooth device requires attention. Others Reserved: Connect to ground for all applications. Bond 1 Bond 2 Bond 3 Asserted: Host device must wake up or remain awake. Deasserted: Host device may sleep when sleep criteria is met. The polarity of this signal is software configurable and can be asserted high or low. Document Number: 002-14881 Rev. *H Page 20 of 51 CYW20735 Table 6. Pin Assignments (Cont.) Pin Name BT_DEV_WAKE QFN Pin I/O Power Domain Description - O VDDO Bluetooth device wake-up: This is a signal from the host to the Bluetooth device that the host requires attention. Asserted: Bluetooth device must wake up or remain awake. Deasserted: Bluetooth device may sleep when sleep criteria is met. The polarity of this signal is software configurable and can be asserted high or low. By default, BT_DEV_WAKE is active-low (if BT-WAKE is low it requires the device to wake up or remain awake). For USB applications, this pin can be used to disable the BT radio, which puts the device in Airport mode. BT_RF 27 I/O PAVDD2P5 RF antenna port CLK_REQ - O VDDO JTAG_SEL 17 - - ARM JTAG debug mode control: connect to GND for all applications RST_N 16 I VDDO Active-low system reset with open-drain output and internal pull-up resistor Used for shared-clock application. BT_TM1 - Reserved: Connect to GND for all applications. BT_VDDC_ISO_2 - Leave floating VDDC_ISO_1 - Leave floating VDDC_ISO_1_2 - Leave floating ANATEST - Leave floating NC 30 Leave floating Document Number: 002-14881 Rev. *H Page 21 of 51 CYW20735 2.2 GPIO Pin Descriptions Table 7. GPIO Pin Descriptionsab QFN Pin Number Pin Name Default Direction POR State Power Domain 8 P0 Input Floating VDDO Default Alternate Function Description GPIO: P0 Keyboard scan input (row): KSI0 A/D converter input 29 Peripheral UART: puart_tx SPI_1: MOSI (master and slave) IR_RX 60Hz_main Note: Not available during TM1 = 1. 9 52 53 54 P1 P2 P3 P4 Input Input Input Input Document Number: 002-14881 Rev. *H Floating Floating Floating Floating VDDO VDDO VDDO VDDO GPIO: P1 Keyboard scan input (row): KSI1 A/D converter input 28 Peripheral UART: puart_rts SPI_1: MISO (master and slave) IR_TX GPIO: P2 Keyboard scan input (row): KSI2 Quadrature: QDX0 Peripheral UART: puart_rx SPI_1: SPI_CS (slave only) SPI_1: MOSI (master only) GPIO: P3 Keyboard scan input (row): KSI3 Quadrature: QDX1 Peripheral UART: puart_cts SPI_1: SPI_CLK (master and slave) GPIO: P4 Keyboard scan input (row): KSI4 Quadrature: QDY0 Peripheral UART: puart_rx SPI_1: MOSI (master and slave) IR_TX Page 22 of 51 CYW20735 Table 7. GPIO Pin Descriptionsab (Cont.) QFN Pin Number Pin Name Default Direction POR State Power Domain 55 P5 Input Floating VDDO 56 57 58 1 2 3 4 P6 P7 P8 P9 P10 P11 P12 Input Input Input Input Input Input Input Document Number: 002-14881 Rev. *H Floating Floating Floating Floating Floating Floating Floating VDDO VDDO VDDO VDDO VDDO VDDO VDDO Default Alternate Function Description GPIO: P5 Keyboard scan input (row): KSI5 Quadrature: QDY1 Peripheral UART: puart_tx SPI_1: MISO (master and slave) BSC: SDA GPIO: P6 Keyboard scan input (row): KSI6 Quadrature: QDZ0 Peripheral UART: puart_rts SPI_1: SPI_CS (slave only) 60Hz_main GPIO: P7 Keyboard scan input (row): KSI7 Quadrature: QDZ1 Peripheral UART: puart_cts SPI_1: SPI_CLK (master and slave) BSC: SCL GPIO: P8 Keyboard scan output (column): KSO0 A/D converter input 27 External T/R switch control: ~tx_pd GPIO: P9 Keyboard scan output (column): KSO1 A/D converter input 26 External T/R switch control: tx_pd GPIO: P10 Keyboard scan output (column): KSO2 A/D converter input 25 External PA ramp control: ~PA_Ramp GPIO: P11 Keyboard scan output (column): KSO3 A/D converter input 24 GPIO: P12 Keyboard scan output (column): KSO4 A/D converter input 23 Page 23 of 51 CYW20735 Table 7. GPIO Pin Descriptionsab (Cont.) QFN Pin Number Pin Name Default Direction POR State Power Domain 5 P13 Input Floating VDDO 59 50 P14 P15 Input Input Floating Floating VDDO VDDO Default Alternate Function Description GPIO: P13 Keyboard scan output (column): KSO5 A/D converter input 22 PWM3 Triac control 3 GPIO: P14 Keyboard scan output (column): KSO6 A/D converter input 21 PWM2 Triac control 4 GPIO: P15 Keyboard scan output (column): KSO7 A/D converter input 20 IR_RX 51 - - - - - P16 P17 P18 P19 P20 P21 Input Input Input Input Input Input Document Number: 002-14881 Rev. *H Floating Floating Floating Floating Floating Floating VDDO VDDO VDDO VDDO VDDO VDDO 60Hz_main GPIO: P16 Keyboard scan output (column): KSO8 A/D converter input 19 GPIO: P17 Keyboard scan output (column): KSO9 A/D converter input 18 GPIO: P18 Keyboard scan output (column): KSO10 A/D converter input 17 GPIO: P19 Keyboard scan output (column): KSO11 A/D converter input 16 GPIO: P20 Keyboard scan output (column): KSO12 GPIO: P21 Keyboard scan output (column): KSO13 A/D converter input 14 Triac control 3 Page 24 of 51 CYW20735 Table 7. GPIO Pin Descriptionsab (Cont.) QFN Pin Number Pin Name Default Direction POR State Power Domain - P22 Input Floating VDDO - - - 13 14 6 P23 P24 P25 P26 PWM0 P27 PWM1 P28 PWM2 Input Input Input Input Input Input Document Number: 002-14881 Rev. *H Floating Floating Floating Floating Floating Floating VDDO VDDO VDDO VDDO VDDO VDDO Default Alternate Function Description GPIO: P22 Keyboard scan output (column): KSO14 A/D converter input 13 Triac control 4 XTALO32K GPIO: P23 Keyboard scan output (column): KSO15 A/D converter input 12 XTALI32K GPIO: P24 Keyboard scan output (column): KSO16 SPI_1: SPI_CLK (master and slave) Peripheral UART: puart_tx GPIO: P25 Keyboard scan output (column): KSO17 SPI_1: MISO (master and slave) Peripheral UART: puart_rx GPIO: P26 Keyboard scan output (column): KSO18 SPI_1: SPI_CS (slave only) Optical control output: QOC0 Triac control 1 Current: 16 mA sink GPIO: P27 Keyboard scan output (column): KSO19 SPI_1: MOSI (master and slave) Optical control output: QOC1 Triac control 2 Current: 16 mA sink GPIO: P28 Optical control output: QOC2 A/D converter input 11 LED1 Current: 16 mA sink Page 25 of 51 CYW20735 Table 7. GPIO Pin Descriptionsab (Cont.) QFN Pin Number Pin Name Default Direction POR State Power Domain 7 P29 PWM3 Input Floating VDDO - - 15 - 10 - P30 PWM4 P31 PWM5 P32 P33 P34 P35 Input Input Input Input Input Input Document Number: 002-14881 Rev. *H Floating Floating Floating Floating Floating Floating VDDO VDDO VDDO VDDO VDDO VDDO Default Alternate Function Description GPIO: P29 Optical control output: QOC3 A/D converter input 10 LED2 Current: 16 mA sink GPIO: P30 A/D converter input 9 Peripheral UART: puart_rts GPIO: P31 A/D converter input 8 Peripheral UART: puart_tx GPIO: P32 A/D converter input 7 Quadrature: QDX0 SPI_1: SPI_CS (slave only) Auxiliary clock output: ACLK0 Peripheral UART: puart_tx GPIO: P33 A/D converter input 6 Quadrature: QDX1 SPI_1: MOSI (slave only) Auxiliary clock output: ACLK1 Peripheral UART: puart_rx GPIO: P34 A/D converter input 5 Quadrature: QDY0 Peripheral UART: puart_rx External T/R switch control: tx_pd GPIO: P35 A/D converter input 4 Quadrature: QDY1 Peripheral UART: puart_cts BSC: SDA Page 26 of 51 CYW20735 Table 7. GPIO Pin Descriptionsab (Cont.) QFN Pin Number Pin Name Default Direction POR State Power Domain - P36 Input Floating VDDO - 11 12 P37 P38 P39 Input Input Input Floating Floating Floating VDDO VDDO VDDO Default Alternate Function Description GPIO: P36 A/D converter input 3 Quadrature: QDZ0 SPI_1: SPI_CLK (master and slave) Auxiliary Clock Output: ACLK0 External T/R switch control: ~tx_pd GPIO: P37 A/D converter input 2 Quadrature: QDZ1 Infrared control: IR_RX SPI_1: MISO (slave only) Auxiliary clock output: ACLK1 BSC: SCL GPIO: P38 A/D converter input 1 SPI_1: MOSI (master and slave) IR_TX Reserved for system use. Leave this GPIO unconnected a. All GPIOs are supermux. All GPIOs can be programmed for any alternative functions. For example, key scan, SPI, I2C, IR_TX, quadrature, peripheral UART, ADC, etc. b. During power-on reset, all inputs are disabled. Document Number: 002-14881 Rev. *H Page 27 of 51 CYW20735 Table 8. GPIO Supermux Input/Output Function List Function Function Function Function SPI_1: CLK SPI_1: CS SPI_1: MOSI SPI_1: MISO SPI_1: INT SPI_2: CLK SPI_2: CS SPI_2: MOSI SPI_2: MISO SPI_2: INT SPI_3: CLK SPI_3: CS SPI_3: MOSI SPI_3: MISO SPI_3: INT UART_RX UART_CTS UART_TX UART_RTS PUART_RX PUART_CTS PUART_TX PUART_RTS SCL SDA SCL2 SDA2 PCM_IN PCM_OUT PCM_CLK PCM_SYNC I2S_DO I2S_DI I2S_WS I2S_CLK IR_TX kso0 kso1 kso2 kso3 kso4 kso5 kso6 kso7 kso8 kso9 kso10 kso11 kso12 kso13 kso14 kso15 kso16 kso17 kso18 kso19 PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 aclk0 aclk1 pa_ramp tx_pd ~tx_pd - Document Number: 002-14881 Rev. *H Page 28 of 51 CYW20735 2.3 Ball Maps 2.3.1 60-Pin QFN Package The 60-pin QFN package is shown in Figure 8. Figure 8. CYW20735 60-Pin QFN Package MICP MICN MIC_AVDD XTALO_32K P16 P15/XTALI_32K P2 P3 P4 P7 P6 P5 P8 P9 P10 P11 P12 P13 P28 P29 P0 P1 P34 P38 P39 P26 P27 P32 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 H MICBIAS UART_CTS_N UART_RTS_N UART_TXD UART_RXD SPI_MISO SPI_MOSI SPI_CSN BT_VDDC BT_VDDO SPI_CLK BT_HOST_WAKE BT_XTALO BT_XTALI BT_PLLVDD1P2 BT_IFVDD1P2 BT_VCOVDD1P2 BT_RF BT_PAVDD2P5 DIGLDO_VDDIN1P5 RFLDO_VDDOUT RFLDO_VDDIN1P5 SR_VDDBAT3V DEFAULT_STRAP PALDO_VDDIN_5V PALDO_VDDOUT3V SR_VLX RST_N HSVSS JTAG_SEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 P14 LHL_VDDO 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Note: Pin H is a ground pin that is used for the signal name HS-VSS. Document Number: 002-14881 Rev. *H Page 29 of 51 CYW20735 3. Specifications 3.1 Electrical Characteristics Caution! The absolute maximum ratings in the following table indicate levels where permanent damage to the device can occur, even if these limits are exceeded for only a brief duration. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended periods can adversely affect long-term reliability of the device Table 9. Absolute Maximum Ratings Requirement Parameter Maximum Junction Temperature Specification Min. Nom. Max. - - 125 Unit C VDD IO -0.5 - 3.795 V VDD RF -0.5 - 1.38 V VDDBAT3V -0.5 - 3.795 V DIGLDO_VDDIN1P5 -0.5 - 1.65 V RFLDO_VDDIN1P5 -0.5 - 1.65 V PALDO_VDDIN_5V -0.5 - 3.795 V MIC_AVDD -0.5 - 3.795 V OTP_3P3V -0.5 - 3.795 V Table 10. ESD/Latchup Requirement Parameter Specification Unit Min. Nom. Max. ESD Tolerance HBM -2000 - 2000 V ESD Tolerance CDM -500 - 500 V - 200 - Latch-up mA Table 11. Environmental Ratings Value Units Operating Temperature Characteristic -30 to +85 C Storage Temperature -40 to +150 C Table 12. Recommended Operating Conditions Parameter VDD IOa VDDRF VDDBAT3Va Specification Unit Min. Typ. Max. VSHUTb 3.0 3.63 V 1.14 1.2 1.26 V VSHUTb 3.0 3.63 V PALDO_VDDIN_5V 2.5 3.3 3.63 DIGLDO_VDDIN1P5 1.3 1.35 1.5 V RFLDO_VDDIN1P5 1.3 1.35 1.5 V MIC_AVDD VSHUTb 3.0 3.63 V OTP_3P3V 3.0 3.3 3.63 V a. VDDIO must be greater or equal to VBAT. b. See Table 13. Document Number: 002-14881 Rev. *H Page 30 of 51 CYW20735 The CYW20735 uses an onboard low voltage detector to shut down the part when supply voltage (VDDBAT3V) drops below operating range. Table 13. Shutdown Voltage Specification Parameter VSHUT Min. Typ. Max. 1.625 1.7 1.775 Unit V 3.1.1 Core Buck Regulator Table 14. Core Buck Regulator Parameter Input supply voltage DC, VBAT Conditions DC voltage range Min. Typ. Max. Unit 1.62 3.0 3.63 V CBUCK output current - - - 65 mA Output voltage range Programmable, 30mV/step default = 1.35V (bits = 0000) 1.2 1.35 1.5 V Output voltage DC accuracy Includes load and line regulation -4 - +4 % LPOM ripple voltage, static Measured with 20 MHz bandwidth limit, static load. Max ripple based on VBAT = 3V, Vout = 1.35V Inductor: 0806 inch-size, Tmax = 1 mm, 2.2 H 25%, DCR = 114 m 20%, ACR<1 (for frequency <1 MHz) Capacitor: 1 F 10%, 6.3V, 0603 inch, X5R, MLCC capacitor + board total-ESR < 20 m - - 30 mVpp Efficiency (high load) 10-50 mA load current, Vout = 1.35V, Vbat = 3V @25C Inductor: 0806 inch-size, Tmax = 1 mm, 2.2 H 25%, DCR = 114 m 20%, ACR<1 (for frequency<1 MHz) Capacitor: 1 F 10%, 6.3V, 0603 inch, X5R, MLCC capacitor +board total-ESR < 20 m - 85 - % Efficiency (low load) 1-5 mA load current, Vout = 1.35V, Vbat = 3V @25C Inductor: 0806 inch-size, Tmax = 1 mm, 2.2 H 25%, DCR = 114 m 20%, ACR<1 (for frequency<1 MHz) Capacitor: 1 F 10%, 6.3V, 0603 inch, X5R, MLCC capacitor +board total-ESR < 20 m - 80 - % Startup time See Table 15 on page 32. - - - - External inductor L 2.2 H 25%, DCR = 114 m 20%, ACR<1 (for frequency<1 MHz) - 2.2 - H External output capacitor, Cout 1 F 10%, 6.3V, 0603 inch, X5R, MLCC capacitor +board total-ESR < 20 m 0.7 1 1.1 F External input capacitor, Cin For SR_VDDBAT 3V pin Ceramic, X5R, 0402, ESR<30 m at 4 MHz, +/-20%, 6.3V, 4.7 F 0.7 4.7 5.64 F Input supply voltage ramp-up time 0 to 3.3V 40 - - s Minimum capacitor value refers to residual capacitor value after taking into account part-to-part tolerance, DC-bias, temperature, and aging. Maximum capacitor value refers to the total capacitance seen at a node where the capacitor is connected. This also includes any decoupling capacitors connected at the load side, if any. Document Number: 002-14881 Rev. *H Page 31 of 51 CYW20735 3.1.2 Digital LDO Table 15. Digital LDO Parameter Input supply voltage, Vin Conditions Min. Typ. Max. Unit Minimum Vin = Vo + 0.12V requirement must be met under maximum load. 1.3 1.35 1.5 V Nominal output voltage,Vo Internal default bit setting Output voltage programmability Range Step size Accuracy at any step (including line/load regulation) Dropout voltage At maximum load - 1.2 - V 0.9 - -4 - 10 - 1.25 - +4 V mV % - - 120 mV 0.2a Output current DC load - 40 mA Output loading capacitor Internal, including the decoupling capacitor to be placed next to the load and the equivalent loading capacitor by the core. 4 - 10 nF Quiescent current At no load, excluding main bandgap Iq - 90 120 A Line regulation Vin from (Vo+0.12V) to 1.5V; 40 mA load - - 5 mV/V Load regulation Load from 1 mA to 25 mA; Vin (Vo+0.12V) - 0.025 0.045 mV/mA Leakage current In full power-down mode or bypass mode: Junction temperature: 25C Junction temperature: 125C - - 0.05 1.1 0.2 5.0 A A PSRR @1 kHz, Vin, Vo+0.12V Output cap of 4 nF~10 nF 40 - - dB LDO turn-on time LDO turn-on time when balance of chip is up - - 22 s External input capacitor Only use an external input capacitor at VDD_DIGLDO1P5 pin if it is not supplied from CBUCK output. - 1 2.2 F a. By default, an internal loading of ~0.2 mA resides inside the LDO. This is to ensure the LDO is stable with zero loading from the core. After the core is up, digital logic can disable this internal loading by setting i_ldo_cntl<8:7> to 00. Document Number: 002-14881 Rev. *H Page 32 of 51 CYW20735 3.1.3 PA LDO Table 16. PA LDO Specification Notes Min. Typ. Max. Units Input supply voltage Min = 3.0 + 0.1V = 3.1V Dropout voltage requirement must be met under max load for performance specs 2.5 3.3 3.63 V Output current Junction temperature 125C Output voltage (Vo) Default = 3.0V - - 50 mA 2.4 3.0 3.4 V - 100 mV +5 % Dropout voltage At max. load - Output voltage DC accuracy Include line/load regulation -5 Quiescent current No load Line regulation Vin from (Vo + 0.1V) to 4.8V, max load - 8 - A +0.2 %Vo/V Load regulation Load from 1 mA to 50 mA Leakage current In Power-Down mode at 25C junction temp - 0.02 0.05 %Vo/mA 0.3 - A PSRR Vbat 3.6V, Vo = 2.5V, Co = l F, max load, 100 Hz to 100 kHz 20 - -0.2 dB LDO turn-on time LDO turn-on time when the rest of the chip is up - - 100 s In-rush current during turn-on From its output cap in the fully-discharged state - - 70 mA External output capacitor (Co) Ceramic, X5R, 0402, (ESR: 30m-200 m), 10%, 6.3V 0.44 1 - F External input capacitor For PALDO_VDDIN_5V pin Ceramic, X5R, 0402, (ESR: 30m-200 m), 10%, 6.3V - 1 - F Document Number: 002-14881 Rev. *H Page 33 of 51 CYW20735 3.1.4 RF LDO Table 17. RF LDO Parameter Input supply voltage, Vin Conditions Min Vin = Vo + 0.15V = 1.35V (for Vo = 1.2V) Dropout voltage requirement must be met under maximum load. Nominal output voltage,Vo Internal default bit setting 000 Output voltage programmability Range Min. Typ. Max. Unit 1.3 1.35 1.5 V - 1.2 - V 1.1 - 1.275 V Step size - 25 - mV Accuracy at any step (including line/load regulation) -4 - +4 % Dropout voltage At maximum load Output current Operating voltage range - - 150 mV 0.1 - 25 mA Quiescent current Line regulation No load - 44 - A Vin from (Vo+0.15V) to 1.5V; 25 mA load - - 5.5 mV/V Load regulation Load from 1 mA to 25 mA; Vin (Vo+0.15V) - 0.025 0.045 mV/mA Load step error Load step from 1 mA-25 mA in 1 s and 25 mA-1 mA in 1s; Vin(Vo+0.15V); Co = 2.2 F - - 35 mV Leakage current Power-down junction temperature: 85C - - 10 A Output noise @30 kHz, 25 mA load, Co = 2.2 F - - 60 nV/Hz @100 kHz, 25 mA load, Co = 2.2 F - - 35 nV/Hz PSRR @1kHz, Input > 1.35V, Co = 2.2 F, Vo = 1.2V 20 - - dB LDO turn-on time LDO turn-on time when balance of chip is up - 140 180 s In-rush current Vin = Vo+0.15V to 1.5V, Co = 2.2 F, no load External output capacitor, Co Total ESR (trace/cap): 5 m-240 m External input capacitor Only use an external input capacitor at RFLDO_VDDIN1P5 pin if it is not supplied from CBUCK output. - - 100 mA 0.5 2.2 4.7 F - 1 2.2 F Note: Minimum capacitor value refers to residual capacitor value after taking into account part-to-part tolerance, DC-bias, temperature, and aging. Document Number: 002-14881 Rev. *H Page 34 of 51 CYW20735 3.1.5 Digital I/O Characteristics Table 18. Digital I/O Characteristics Characteristics Symbol Minimum Typical Maximum Unit Input low voltage (VDDO = 3.3V) VIL - - 0.8 V Input high voltage (VDDO = 3.3V) VIH 2.0 - - V Input low voltage (VDDO = 1.8V) VIL - - 0.6 V Input high voltage (VDDO = 1.8V) VIH 1.1 - - V Output low voltage VOL - - 0.4 V Output high voltage VOH VDDO - 0.4V - - V Input low current IIL - - 1.0 A Input high current IIH - - 1.0 A Output low current (VDDO = 3.3V, VOL = 0.4V) IOL - - 2.0 mA Output high current (VDDO = 3.3V, VOH = 2.9V) IOH - - 4.0 mA Output high current (VDDO = 1.8V, VOH = 1.4V) IOH - - 2.0 mA Input capacitance CIN - - 0.4 pF 3.1.6 Current Consumption In Table 19, current consumption measurements are taken at VBAT with the assumption that VBAT is connected to VDDIO and LDOIN. Table 19. BLE Current Consumption Operational Mode Conditions Typical Unit Receiving Receiver and baseband are both operating, 100% ON. 8 mA Transmitting Transmitter and baseband are both operating, 100% ON. 18 mA Advertising 1.28s direct advertising in low power idle mode Scanning TBD Connecting 1-second connection interval in low power idle mode HIDOFF (Deep Sleep) Document Number: 002-14881 Rev. *H - 30 A TBD mA 25 A 1 A Page 35 of 51 CYW20735 3.2 ADC Electrical Characteristics Table 20. ADC Electrical Characteristics Parameter Analog supply voltage Analog core supply Audio supply Symbol avddBAT AVDDC Mic_avdd Current consumption ITOT Power down current - Min. Typ. Max. Unit Battery and I/O supply Conditions/Comments 1.62 - 3.6 V 10% 1.08 1.2 1.32 V Only available for audio application 1.8 2.5 3.3 V - - 2 3 mA At room temperature - 1 - A From BG with 3% accuracy - 0.85 - V ADC Core Specification ADC reference voltage VREF ADC sampling clock - - - 12 - MHz Absolute error - Includes gain error, offset and distortion. Without factory calibration. - - 5 % Includes gain error, offset and distortion. After factory calibration. - - 2 % For audio application 12 13 - Bit For static measurement 10 - - - 1.6 - 1.8 - 3.6 ENOB ADC input full scale - FS For audio application For static measurement Conversion rate Signal bandwidth Input impedance Startup time - - RIN - For audio application 8 16 - For static measurement 16 20 - For audio application 20 - 8K For static measurement - DC - For audio application 10 - - For static measurement 500 - - kHz Hz K For audio application - 10 - ms For static measurement - 20 - s 0 - 42 dB MIC PGA Specifications MIC PGA gain range - - MIC PGA gain step - - - 1 - dB MIC PGA gain error - Includes part-to-part gain variation -1 - 1 dB PGA input referred noise - At 42 dB PGA gain A-weighted - - 4 V Passband gain flatness - PGA and ADC, 100 Hz-4 kHz -0.5 - 0.5 dB MIC bias output voltage - At 2.5V supply - 2.1 - V MIC bias loading current - - - - 3 mA MIC bias noise - Refers to PGA input 20 Hz to 8 kHz, A-weighted - - 3 V MIC bias PSRR - at 1 kHz 40 - - dB MIC Bias Specifications ADC SNR - A-weighted 0 dB PGA gain 78 - - dB ADC THD + N - -3 dBFS input 0 dB PGA gain 74 - - dB Always lower than avddBAT - - 3.6 V Resistance - - 1 k Capacitance - - 10 pF GPIO input voltage GPIO source impedancea - a. Conditional requirement for the measurement time of 10 s. Relaxed with longer measurement time for each GPIO input channel. Document Number: 002-14881 Rev. *H Page 36 of 51 CYW20735 3.3 RF Specifications Note: Table 21 and Table 22 on page 42 apply to single-ended industrial temperatures. Unused inputs are left open. Table 21. Receiver RF Specifications Parameter Minimum Typical a Maximum Unit 2402 - 2480 MHz - - -91.5 - - GFSK, 1 Mbps - - -20 dBm Conditions General Frequency range RX sensitivity b Maximum input - Interference Performance TBD Out-of-Band Blocking Performance (CW)c 30 MHz-2000 MHz 0.1% BER - -10.0 - dBm 2000-2399 MHz 0.1% BER - -27 - dBm 2498-3000 MHz 0.1% BER - -27 - dBm 3000 MHz-12.75 GHz 0.1% BER - -10.0 - dBm - -39.0 - - dBm Intermodulation Performanced BT, Df = 4 MHz Spurious Emissionse 30 MHz to 1 GHz - - - -62 dBm 1 GHz to 12.75 GHz - - - -47 dBm 65 MHz to 108 MHz FM RX - -147 - dBm/Hz 746 MHz to 764 MHz CDMA - -147 - dBm/Hz 851-894 MHz CDMA - -147 - dBm/Hz 925-960 MHz EDGE/GSM - -147 - dBm/Hz 1805-1880 MHz EDGE/GSM - -147 - dBm/Hz 1930-1990 MHz PCS - -147 - dBm/Hz 2110-2170 MHz WCDMA - -147 - dBm/Hz a. b. c. d. Typical operating conditions are 1.22V operating voltage and 25C ambient temperature. The receiver sensitivity is measured at BER of 0.1% on the device interface. Meets this specification using front-end band pass filter. f0 = -64 dBm Bluetooth-modulated signal, f1 = -39 dBm sine wave, f2 = -39 dBm Bluetooth-modulated signal, f0 = 2f1 - f2, and |f2 - f1| = n*1 MHz, where n is 3, 4, or 5. For the typical case, n = 4. e. Includes baseband radiated emissions. Document Number: 002-14881 Rev. *H Page 37 of 51 CYW20735 Table 22. Transmitter RF Specifications (TBD) Parameter Conditions Minimum Typical Maximum Unit Frequency range - 2402 - 2480 MHz Class 1: GFSK TX power - - 10 - dBm Power control step - 2 4 8 dB - - - -36.0a dBm dBm General Out-of-Band Spurious Emissions 30 MHz to 1 GHz 1 GHz to 12.75 GHz - - - -30.0a, b 1.8 GHz to 1.9 GHz - - - -47.0 dBm 5.15 GHz to 5.3 GHz - - - -47.0 dBm Conditions Minimum Typical Maximum Unit N/A 2402 - 2480 MHz a. Maximum value is the value required for Bluetooth qualification. b. Meets this spec using a front-end band-pass filter. Table 23. BLE RF Specifications Parameter Frequency range RX sensea GFSK, 0.1% BER, 1 Mbps - -94.5 - dBm TX powerb N/A - 9 - dBm Mod Char: Delta F1 average N/A 225 255 275 kHz Mod Char: Delta F2 maxc N/A 99.9 - - % Mod Char: Ratio N/A 0.8 0.95 - % a. Dirty TX is Off. b. The BLE TX power can be increased to compensate for front-end losses such as BPF, diplexer, switch, etc. The output is capped at 12 dBm out. The BLE TX power at the antenna port cannot exceed the 10 dBm EIRP specification limit. c. At least 99.9% of all delta F2 max frequency values recorded over 10 packets must be greater than 185 kHz. Document Number: 002-14881 Rev. *H Page 38 of 51 CYW20735 3.4 Timing and AC Characteristics In this section, use the numbers listed in the Reference column of each table to interpret the following timing diagrams. 3.4.1 UART Timing Table 24. UART Timing Specifications Min. Max. Unit 1 Reference Delay time, UART_CTS_N low to UART_TXD valid Characteristics - 1.50 Baud periods 2 Setup time, UART_CTS_N high before midpoint of stop bit - 0.67 Baud periods 3 Delay time, midpoint of stop bit to UART_RTS_N high - 1.33 Baud periods Figure 9. UART Timing Document Number: 002-14881 Rev. *H Page 39 of 51 CYW20735 3.4.2 SPI Timing The SPI interface can be clocked up to 12 MHz. Table 25 and Figure 10 show the timing requirements when operating in SPI Mode 0 and 2. Table 25. SPI Mode 0 and 2 Min. Max. Unit 1 Reference Time from master assert SPI_CSN to first clock edge Characteristics 45 - ns 2 Hold time for MOSI data lines 12 1/2 SCK ns 3 Time from last sample on MOSI/MISO to slave deassert SPI_INT 0 100 ns 4 Time from slave deassert SPI_INT to master deassert SPI_CSN 5 Idle time between subsequent SPI transactions 0 - ns 1 SCK - ns Figure 10. SPI Timing, Mode 0 and 2 5 SPI_CSN SPI_INT (DirectWrite) 3 4 SPI_INT (DirectRead) 1 SPI_CLK (Mode 0) SPI_CLK (Mode 2) 2 First Bit SPI_MOSI SPI_MISO Not Driven First Bit Document Number: 002-14881 Rev. *H Second Bit Last bit Second Bit Last bit Not Driven Page 40 of 51 CYW20735 Table 26 and Figure 11 show the timing requirements when operating in SPI Mode 1 and 3. Table 26. SPI Mode 1 and 3 Reference Min. Max. Unit Time from master assert SPI_CSN to first clock edge 45 - ns 2 Hold time for MOSI data lines 12 1/2 SCK ns 3 Time from last sample on MOSI/MISO to slave deassert SPI_INT 0 100 ns 1 Characteristics 4 Time from slave deassert SPI_INT to master deassert SPI_CSN 5 Idle time between subsequent SPI transactions 0 - ns 1 SCK - ns Figure 11. SPI Timing, Mode 1 and 3 SPI_CSN 5 SPI_INT (DirectWrite) 3 4 SPI_INT (DirectRead) SPI_CLK (Mode 1) 1 SPI_CLK (Mode 3) 2 SPI_MOSI SPI_MISO Not Driven Invalid bit First bit Last bit Invalid bit First bit Last bit Document Number: 002-14881 Rev. *H Not Driven Page 41 of 51 CYW20735 3.4.3 I2C Interface Timing The specifications in Table 27 references Figure 12. Table 27. I2C Interface Timing Specifications (up to 1 MHz) Reference 1 Characteristics Clock frequency Minimum Maximum Unit - 100 kHz 400 800 1000 2 START condition setup time 650 - ns 3 START condition hold time 280 - ns 4 Clock low time 650 - ns 5 Clock high time 280 - ns 6 Data input hold timea 0 - ns 7 Data input setup time 100 - ns 8 STOP condition setup time 280 - ns 9 Output valid from clock - 400 ns 10 Bus free timeb 650 - ns a. As a transmitter, 125 ns of delay is provided to bridge the undefined region of the falling edge of SCL to avoid unintended generation of START or STOP conditions. b. Time that the CBUS must be free before a new transaction can start. Figure 12. I2C Interface Timing Diagram 1 5 SCL 2 4 8 6 3 7 SDA IN 10 9 SDA OUT Document Number: 002-14881 Rev. *H Page 42 of 51 CYW20735 Table 28. Timing for I2S Transmitters and Receivers Transmitter Lower LImit Clock Period T Receiver Upper Limit Lower Limit Upper Limit Notes Min Max Min Max Min Max Min Max Ttr - - - Tr - - - a Master Mode: Clock generated by transmitter or receiver HIGH tHC 0.35Ttr - - - 0.35Ttr - - - b LOWtLC 0.35Ttr - - - 0.35Ttr - - - b Slave Mode: Clock accepted by transmitter or receiver HIGH tHC - 0.35Ttr - - - 0.35Ttr - - c LOW tLC - 0.35Ttr - - - 0.35Ttr - - c Rise time tRC - - 0.15Ttr - - - - d Transmitter Delay tdtr - - - 0.8T - - - - e Hold time thtr 0 - - - - - - - d Setup time tsr - - - - - 0.2Tr - - f Hold time thr - - - - - 0 - - f Receiver a. The system clock period T must be greater than Ttr and Tr because both the transmitter and receiver have to be able to handle the data transfer rate. b. At all data rates in master mode, the transmitter or receiver generates a clock signal with a fixed mark/space ratio. For this reason, tHC and tLC are specified with respect to T. c. In slave mode, the transmitter and receiver need a clock signal with minimum HIGH and LOW periods so that they can detect the signal. So long as the minimum periods are greater than 0.35Tr, any clock that meets the requirements can be used. d. Because the delay (tdtr) and the maximum transmitter speed (defined by Ttr) are related, a fast transmitter driven by a slow clock edge can result in tdtr not exceeding tRC which means thtr becomes zero or negative. Therefore, the transmitter has to guarantee that thtr is greater than or equal to zero, so long as the clock rise-time tRC is not more than tRCmax, where tRCmax is not less than 0.15Ttr. e. To allow data to be clocked out on a falling edge, the delay is specified with respect to the rising edge of the clock signal and T, always giving the receiver sufficient setup time. f. The data setup and hold time must not be less than the specified receiver setup and hold time. Document Number: 002-14881 Rev. *H Page 43 of 51 CYW20735 Figure 13. I2S Transmitter Timing T tRC* tLC > 0.35T tHC > 0.35T VH = 2.0V SCK VL = 0.8V thtr > 0 totr < 0.8T SD and WS T = Clock period Ttr = Minimum allowed clock period for transmitter T = Ttr * tRC is only relevant for transmitters in slave mode. Figure 14. I2S Receiver Timing T tLC > 0.35T tHC > 0.35 VH = 2.0V SCK VL = 0.8V tsr > 0.2T thr > 0 SD and WS T = Clock period Tr = Minimum allowed clock period for transmitter T > Tr Document Number: 002-14881 Rev. *H Page 44 of 51 CYW20735 4. Mechanical Information 4.1 Package Diagrams 4.1.1 60-Pin QFN Package Figure 15. CYW20735 7 mm x 7 mm 60-Pin QFN Package Document Number: 002-14881 Rev. *H Page 45 of 51 CYW20735 4.2 Tray Packaging Specifications 4.2.1 QFN The CYW20735 QFN package and tray dimensions are annotated in Figure 16 and defined in Table 29 and Table 30 on page 46. Figure 16. QFN Package and Tray Dimensions Table 29. QFN Package Dimensions and Tolerances Parameter Nom. Min. Max. Tol. Unit P1 Package size Description 7 6.9 7.1 0.1 mm P2 Top hat width 0 0 0 - mm P3 Top hat height 0 0 0 - mm P4 Substrate thickness 0.85 0.8 0.9 0.05 mm P7 Total thickness (P3 + P4) 0.85 0.8 0.9 0.05 mm Table 30. QFN Tray Dimensions and Tolerances Parameter Nom. Min. Max. Tol. Unit T1 Top pocket size 7.25 7.17 7.33 0.08 mm T3 Top pocket depth 1.75 1.5 2 0.25 mm T5 Stacking height 2 1.87 2.13 0.13 mm T6 Bottom pocket size 7.25 7.17 7.33 0.08 mm T8 Bottom pocket depth 1.650 1.52 1.78 0.13 mm a2 Bottom pocket relief wall draft angle T10 Description Packing value between two stacking trays Document Number: 002-14881 Rev. *H 5 5 5 0 Degrees 0.2 0.07 0.33 0.13 mm Page 46 of 51 CYW20735 5. Ordering Information Table 31. Ordering Information Part Number CYW20735PKML1G Package Ambient Operating Temperature 60-pin QFN 0C to 70C 6. Additional Information 6.1 IoT Resources Cypress provides a wealth of data at http://www.cypress.com/internet-things-iot to help you to select the right IoT device for your design, and quickly and effectively integrate the device into your design. Cypress provides customer access to a wide range of information, including technical documentation, schematic diagrams, product bill of materials, PCB layout information, and software updates. Customers can acquire technical documentation and software from the Cypress Support Community website (https://community.cypress.com/) 6.2 Acronyms and Abbreviations In most cases, acronyms and abbreviations are defined upon first use. For a more complete list of acronyms and other terms used in Cypress documents, go to: http://www.cypress.com/glossary. The following list of acronyms and abbreviations may appear in this document. Term Description ADC analog-to-digital converter AFH adaptive frequency hopping AHB advanced high-performance bus APB advanced peripheral bus APU audio processing unit ARM7TDMI-STM Acorn RISC Machine 7 Thumb instruction, Debugger, Multiplier, Ice, Synthesizable BSC Broadcom Serial Control BTC Bluetooth controller COEX coexistence DFU device firmware update DMA direct memory access EBI external bus interface HCI Host Control Interface HV high voltage IDC initial digital calibration IF intermediate frequency IRQ interrupt request JTAG Joint Test Action Group LCU link control unit LDO low drop-out LHL lean high land LPO low power oscillator LV LogicVisionTM MIA multiple interface agent PDM pulse density modulation PLL phase locked loop PMU power management unit Document Number: 002-14881 Rev. *H Page 47 of 51 CYW20735 Term Description POR power-on reset PWM pulse width modulation QD quadrature decoder RAM random access memory RC oscillator A resistor-capacitor oscillator is a circuit composed of an amplifier, which provides the output signal, and a resistor-capacitor network, which controls the frequency of the signal. RF radio frequency ROM read-only memory RX/TX receive, transmit SPI serial peripheral interface SW software SWD serial wire debug UART universal asynchronous receiver/transmitter UPI -processor interface WD watchdog Document Number: 002-14881 Rev. *H Page 48 of 51 CYW20735 Document History Page Document Title: CYW20735 Single-Chip Bluetooth Transceiver for Wireless Input Devices Document Number: 002-14881 Revision ECN Orig. of Change Submission Date ** - - 05/19/2015 20735-DS100-R Initial release *A - - 10/13/2015 20735-DS101-R See the release for the applicable change description. *B - - 11/09/2015 20735-DS102-R Updated: Table 3: "Reference Crystal Electrical Specifications," on page 21. Section 5: "Ordering Information," on page 60: updated the part number for the QFN chip. *C - - 12/04/2015 20735-DS103-R Updated: Table 3: "Reference Crystal Electrical Specifications," on page 22. Table 9: "Core Buck Regulator," on page 45. Table 10: "Digital LDO," on page 46. Table 11: "PA LDO," on page 47. Table 12: "RF LDO," on page 48. Table 13: "Digital I/O Characteristics," on page 49. Table 14: "BLE Current Consumption," on page 49. Table 19: "UART Timing Specifications," on page 54. Added: * "Tray Packaging Specifications" on page 60. Removed * Table 15: "BR Current Consumption," on page 48. * "Tape and Reel Packaging Specifications," on page 59. *D - - 03/10/2016 20735-DS104-R Updated: Table 14: "BLE Current Consumption," on page 46 *E - - 05/26/2016 20735-DS105-R Updated: Table8:"Absolute Maximum Ratings," on page42. Table13:"Core Buck Regulator," on page44. Table14:"Digital LDO," on page45. Table15:"PA LDO," on page46. Table16:"RF LDO," on page47. Table19:"ADC Microphone Specifications," on page49. Added: "Table 9:"ESD/Latchup," on page42. Table10:"Environmental Ratings," on page43. Table11:"Recommended Operating Conditions," on page43. Table12:"Shutdown Voltage," on page43. "Power-On Reset" on page14 "Brownout Detection" on page14 Description of Change *F 5446946 UTSV 09/29/2016 Converted to Cypress template *G 5688133 CLEU 05/22/2017 Updated Table 24. UART Timing Specifications. Added Table 28, Figure 13 and Figure 14. Document Number: 002-14881 Rev. *H Page 49 of 51 CYW20735 Document Title: CYW20735 Single-Chip Bluetooth Transceiver for Wireless Input Devices Document Number: 002-14881 *H 6123642 MILI Document Number: 002-14881 Rev. *H 04/18/2018 Removed "CYW20735KFBG" from Mapping Table for Part Number between Broadcom and Cypress and Ordering Information. Removed "111 pin fine pitch ball grid array (FBGA)" throughout the document. Replaced Default Alternate Function Description for QFN Pin 12 as "Reserved for system use. Leave this GPIO unconnected". Removed 1.17 Infrared Learning. Removed FBGA Pin Number column from Table 6 and Table 7. Added Table 2. Bluetooth Features. Changed BSC to I2C throughout the document. Page 50 of 51 CYW20735 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC(R) Solutions Products Arm(R) Cortex(R) Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers Interface cypress.com/clocks cypress.com/interface Internet of Things Memory cypress.com/iot cypress.com/memory Microcontrollers cypress.com/mcu PSoC cypress.com/psoc Power Management ICs Cypress Developer Community Community | Projects | Video | Blogs | Training | Components Technical Support cypress.com/support cypress.com/pmic Touch Sensing cypress.com/touch USB Controllers Wireless Connectivity PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU cypress.com/usb cypress.com/wireless 51 (c) Cypress Semiconductor Corporation, 2015-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress does not assume any liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress product. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 002-14881 Rev. *H Revised Wednesday, April 18, 2018 Page 51 of 51