Freescale Semiconductor Technical Data Document Number: MC1322x Rev. 1.3 10/2010 MC1322x Package Information Case 1901-01 99-Pin [9.5X9.5X1.2mm] MC1322x Advanced ZigBeeTM- Compliant Platform-in-Package (PiP) for the 2.4 GHz IEEE(R) 802.15.4 Standard Ordering Information Device MC13224V1 MC13224VR2 MC13226V 1 MC13226VR2 1 1 Introduction 1 1 Device Marking Package MC13224V LGA MC13224V LGA MC13226V LGA MC13226V LGA See Table 1 for more details. Contents The MC1322x family is Freescale's third-generation ZigBee platform which incorporates a complete, low power, 2.4 GHz radio frequency transceiver, 32-bit ARM7 core based MCU, hardware acceleration for both the IEEE 802.15.4 MAC and AES security, and a full set of MCU peripherals into a 99-pin LGA Platform-in-Package (PiP). The MC1322x solution can be used for wireless applications ranging from simple proprietary point-to-point connectivity to complete ZigBee mesh networking. The MC1322x is designed to provide a highly integrated, total solution, with premier processing capabilities and very low power consumption. 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 High Density, Low Component Count, Integrated IEEE 802.15.4 Solution 10 4 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5 MCU Peripherals . . . . . . . . . . . . . . . . . . . . . . 19 6 Pin Assignments and Connections . . . . . . 28 7 System Electrical Specification . . . . . . . . . 36 8 Developer Environment . . . . . . . . . . . . . . . . 48 9 Mechanical Diagrams (Case 1901-01, non-JEDEC) 51 The MC1322x MCU resources offer superior processing power for ZigBee applications. A full 32-bit ARM7TDMI-S core operates up to 26 MHz. A 128 Kbyte FLASH memory is mirrored into a 96 Kbyte RAM for upper stack and applications software. In addition, an 80 Kbyte ROM is available for boot software, standardized IEEE 802.15.4 MAC and Freescale reserves the right to change the detail specifications as may be required to permit improvements in the design of its products. (c) Freescale Semiconductor, Inc., 2005, 2006, 2007, 2008, 2009, 2010. All rights reserved. communications stack software. A full set of peripherals and Direct Memory Access (DMA) capability for transceiver packet data complement the processor core. The RF radio interface provides for low cost and the high density as shown in Figure 1. An onboard balun along with a TX/RX switch allows direct connection to a single-ended 50- antenna. The integrated PA provides programmable output power typically from -30 dBm to +4 dBm, and the RX LNA provides -96 dBm sensitivity. In addition, separate complementary PA outputs allow use of an external PA and/or an external LNA for extended range applications. The device also has onboard bypass capacitors and crystal load capacitors for the smallest footprint in the industry. All components are integrated into the package except the crystal and antenna. PA BALUN ANALOG TRANSMITTER RF TX/RX SWITCH LNA ANALOG RECEIVER Figure 1. MC1322x RF Radio Interface In addition to the best-in-class MCU performance and power, the MC1322x also provides best-in-class power savings. Typical transmit current is 29 mA and typical receive current is 22 mA with the CPU at 2 MHz operation and even lower with the bus stealing enabled. Onboard power supply regulation is provided for source voltages from 2.0 Vdc to 3.6 Vdc. Numerous low current modes are available to maximize battery life including sleep or restricted performance operation. Applications include, but are not limited to, the following: * Residential and commercial automation -- Lighting control -- Security -- Access control -- Heating, ventilation, air-conditioning (HVAC) -- Automated meter reading (AMR) * Industrial Control MC1322x Technical Data, Rev. 1.3 2 Freescale Semiconductor * * 1.1 -- Asset tracking and monitoring -- Homeland security -- Process management -- Environmental monitoring and control -- HVAC -- Automated meter reading Health Care -- Patient monitoring -- Fitness monitoring Consumer -- Remote control -- Entertainment systems -- Cellular phone attach Available Devices The MC1322x family is available as two part numbers. These device types differ only in their ROM contents, all other device hardware, performance, and specifications are identical: * MC13224V - this is the original version and is the generic part type. -- The MC13224V is intended for most IEEE 802.15.4 applications including MAC-based, ZigBee-2007 Profile 1, and ZigBee RF4CE targets. -- It has a more complete set of peripheral drivers in ROM. * MC13226V - this is a more recent version and is provided specifically for ZigBee-2007 Profile 2 (Pro) applications. Only the onboard ROM image has been changed to optimize ROM usage for the ZigBee Pro profile and maximize the amount of available RAM for application use. -- The IEEE MAC/PHY functionality has been streamlined to include only that functionality required by the ZigBee specification. The MAC functionality is 802.15.4 compatible. -- For a typical application, up to 20 kbytes more of RAM is available versus the M13224V -- Some drivers present in the MC13224 ROM have been removed and these include the ADC, LCDfont, and SSI drivers. These drivers are still available as library functions, but now compile into the RAM space. -- The Low Level Component (LLC) functionality has also been streamlined for the ZigBee specification * * NOTE When running the Freescale IEEE 802.15.4 MAC (or a related stack) on the MC1322x platform, neither beaconing or GTS are supported. See the MC1322x Reference Manual (Document No MC1322xRM), for information on using applications on these devices. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 3 1.2 Ordering Information Table 1 provides additional details about the MC1322x Table 1. Orderable Parts Details Device Operating Temp Range (TA.) Memory Options Package MC13224V -40 to 105 C LGA MC13224VR2 -40 to 105 C LGA Tape and Reel MC13226V -40 to 105 C LGA MC13226VR2 -40 to 105 C LGA Tape and Reel 2 Description 96KB RAM, Intended for 802.15.4 Standard compliant applications, 128KB Flash Freescale 802.15.4 MAC, and Freescale BeeStackTM. 96KB RAM, Intended specifically for Freescale BeeStackTM Pro 128KB Flash applications. Features This section provides a simplified block diagram and highlights MC1322x features. 2.1 Block Diagram Figure 2 shows a simplified block diagram of the MC1322x. 24 MHz (typ) 32.768 KHz (optional) BATTERY DETECT CLOCK & RESET MODULE (CRM) DUAL 12-BIT ADC MODULE RADIO INTERFACE MODULE (RIF) ANALOG TRANSMITTER BALUN RF TX/RX SWITCH ANALOG RECEIVER JTAG/ Nexus DEBUG DIGITAL MODEM TX MODEM RX MODEM 802.15.4 MAC ACCELERATOR (MACA) IEEE 802.15.4 TRANSCEIVER ADVANCED SECURITY MODULE (ASM) MC1322x SPI FLASH MODULE (SPIF) Buck Regulator ANALOG POWER MANAGEMENT & VOLTAGE REGULATION 128KBYTE NON-VOLATILE MEMORY (SERIAL FLASH) ARM7 TDMI-S 32-BIT CPU BUS INTERFACE & MEMORY ARBITRATOR ARM INTERRUPT CONTROLLER (AITC) 96KBYTE SRAM (24K WORDS x 32 BITS) 80KBYTE ROM (20KWORDS x 32 BITS) TIMER MODULE (TMR) (4 Tmr Blocks) UART MODULE (UART0) UART MODULE (UART1) SYNC SERIAL INTERFACE (SSI/i2S) KEYBOARD INTERFACE (KBI) UP TO 64 IO PINS RF OSCILLATOR & CLOCK GENERATION INTER-IC BUS MODULE (I2C) SERIAL PERIPHERAL INTERFACE (SPI) GPIO and IO CONTROL Figure 2. MC1322x Simplified Block Diagram MC1322x Technical Data, Rev. 1.3 4 Freescale Semiconductor 2.2 * * * * * * * * Features Summary IEEE 802.15.4 standard compliant on-chip transceiver/modem -- 2.4 GHz ISM Band operation -- 16 selectable channels -- Programmable transmitter output power (-30 dBm to +4 dBm typical) -- World-class receiver sensitivity - < -96 dBm typical receiver sensitivity using DCD mode (<1% PER, 20-byte packets) - < -100 dBm typical receiver sensitivity using NCD mode (<1% PER, 20-byte packets) Hardware acceleration for IEEE 802.15.4 applications -- MAC accelerator (sequencer and DMA interface) -- Advanced encryption/decryption hardware engine (AES 128-bit) Supports standard IEEE 802.15.4 signaling with 250 kbps data rate 32-bit ARM7TDMI-S CPU core with programmable performance up to 26 MHz (24 MHz typical) Extensive on-board memory resources -- 128 Kbyte serial FLASH memory (will be mirrored into RAM) -- 96 Kbyte SRAM -- 80 Kbyte ROM Best-in-class power dissipation -- 22 mA typical RX current draw (DCD mode) with radio and MCU active -- 29 mA typical TX current draw with radio and MCU active (coin cell capable) -- 3.3 mA typical current draw with MCU active (radio off) -- 0.8 mA typical current with MCU idle (radio off) -- 0.85 A typical Hibernate current (retain 8 Kbyte SRAM contents) -- 0.4 A maximum Off current (device in reset) Extensive sleep mode control and variation -- Hibernate and Doze low power modes -- Programmable degree of power down -- Clock management -- Onboard 2 kHz oscillator for wake-up timer. -- Optional 32.768 kHz crystal oscillator for accurate real-time sleep mode timing and wake-up with a possible sleep period greater than 36.4 hours -- Wake-up through programmable timer, external real-time interrupts, or ADC timer Extensive MCU peripherals set -- Dedicated 802.15.4 modem/radio interface module (RIF) -- Dedicated NVM SPI interface for managing FLASH memory -- Two dedicated UART modules capable of 2 Mbps with CTS/RTS support -- SPI port with programmable master and slave operation MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 5 * * * * * * * * -- 8-pin keyboard interface (KBI) supports up to a 4x4 matrix. Also, provides up to four asynchronous interrupt inputs for wake-up -- Two 12-bit analog-to-digital converters (ADCs) share 8 input channels -- Four independent 16-bit timers with PWM capability. These can cascade in combinations up to 64-bit operation -- Inter-integrated circuit (I2C) interface -- Synchronous Serial Interface (SSI) with I2S and SPI capability and FIFO data buffering -- Up to 64 programmable I/O shared by peripherals and GPIO Powerful In-circuit debug and FLASH programming available via on-chip debug ports -- JTAG debug port -- Nexus extended feature debug port System protection features -- Low battery detect -- Watchdog timer (COP) -- Sleep mode timer Low external component count -- Only antenna needed for single-ended 50- RF interface (balun in package) -- Only a single crystal is required for the main oscillator; programmable crystal load capacitors are on-chip -- All bypass capacitors in package Supports single crystal reference clock source (typical 24 MHz crystal with 13 - 26 MHz usable) with on-chip programmable crystal load capacitance or external frequency source. Also provides onboard 2 kHz oscillator for wake-up timing or an optional 32.768 kHz crystal for accurate low power timing. 2.0 V to 3.6 V operating voltage with on-chip voltage regulators. Optional buck converter for better battery life. -40 C to +105 C temperature range RoHS-compliant 9.5mm x 9.5mm x 1.2mm 99-pin LGA package MC1322x Technical Data, Rev. 1.3 6 Freescale Semiconductor 2.3 Software Solutions Freescale provides a powerful software environment called the Freescale BeeKit Wireless Connectivity Toolkit. BeeKit is a comprehensive codebase of wireless networking libraries, application templates, and sample applications. The BeeKit Graphical User Interface (GUI), part of the BeeKit Wireless Connectivity Toolkit, allows users to create, modify, and update various wireless networking implementations. A wide range of software functionality is available to complement the MC1322x and these are provided as codebases within BeeKit. The following sections describe the available tools. NOTE The MC13226V is intend specifically for use with the BeeStack codebase, see Section 2.3.4.2, "Using BeeStack on the MC1322x Platform". 2.3.1 Simple Media Access Controller (22xSMAC) The Freescale Simple Media Access Controller (22xSMAC) is a simple ANSI C based code stack available as sample source code. The SMAC can be used for developing proprietary RF transceiver applications using the MC1322x. * Supports point-to-point and star network configurations * Proprietary networks * Source code and application examples provided 2.3.2 IEEE 802.15.4 2006 Standard-Compatible MAC The Freescale 802.15.4 Standard MAC is a code stack available as object code. The 802.15.4 MAC is used in two ways: * The 802.15.4 MAC is the heart of all Freescale non-SMAC codebases. All higher level stacks are built on the MAC services * Customers also use the MAC for developing networking applications based on the full IEEE(R) 802.15.4 Standard but having custom Network Layer and application services. NOTE The basic MAC is fully 802.15.4 compliant on the HCS08 platform; however, on the MC1322x ARM platform, beaconing and GTS are not supported. This has no impact on ZigBee stacks as these do not utilize these features. Features of the 22x MAC include * Supports star, mesh and cluster tree topologies * Does not support beaconed networks * Does not supports GTS * Multiple power saving modes * AES-128 Security module * 802.15.4 Sequence support MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 7 * * 802.15.4 Receiver Frame filtering. Binaries and application examples provided 2.3.3 SynkroRF Platform The SynkroRF Network is a general purpose, proprietary networking layer that sits on top of the IEEE(R) 802.15.4 MAC and PHY layers. It is designed for Wireless Personal Area Networks (WPANs) and conveys information over short distances among the participants in the network. It enables small, power efficient, inexpensive solutions to be implemented for a wide range of applications. Some key characteristics of an SynkroRF Network are: * An over-the-air data rate of 250 kbit/s in the 2.4 GHz band. * 3 independent communication channels in the 2.4 GHz band (15, 20, and 25). * 2 network node types, controller and controlled nodes. * Channel Agility mechanism. * Low Latency Tx mode automatically enabled in conditions of radio interference. * Fragmented mode transmission and reception, automatically enabled in conditions of radio interference. * Robustness and ease of use. * Essential functionality to build and support a CE network. The SynkroRF Network layer uses components from the standard HC(S)08 Freescale platform, which is also used by the Freescale's implementations of 802.15.4. MAC and ZigBeeTM layers. For more details about the platform components, see the Freescale Platform Reference Manual. 2.3.4 ZigBee-Based Stacks Freescale has two independent codebases to support the two ZigBee standard specifications: * BeeStackTM - supports ZigBee-2007 and ZigBee Pro extensions * BeeStack Consumer - supports ZigBee RF4CE 2.3.4.1 BeeStack Freescale's BeeStack architecture implements the ZigBee-2007 protocol stack including both Stack Profile 1 and Stack Profile 2 (Pro). Based on the OSI Seven-Layer model, the ZigBee stack ensures inter-operability among networked devices. The physical (PHY), media access control (MAC), and network (NWK) layers create the foundation for the application (APL) layers. BeeStack defines additional services to improve the communication between layers of the protocol stack. At the Application Layer, the application support layer (ASL) facilitates information exchange between the Application Support Sub-Layer (APS) and application objects. Finally, ZigBee Device Objects (ZDO), in addition to other manufacturer-designed applications, allow for a wide range of useful tasks applicable to home and industrial automation. MC1322x Technical Data, Rev. 1.3 8 Freescale Semiconductor BeeStack uses the IEEE 802.15.4-compatible MAC/PHY layer that is not part of ZigBee itself. The NWK layer defines routing, network creation and configuration, and device synchronization. The application framework (AF) supports a rich array of services that define ZigBee functionality. ZigBee Device Objects (ZDO) implement application-level services in all nodes via profiles. A security service provider (SSP) is available to the layers that use encryption (NWK and APS), i.e., Advanced Encryption Standard (AES) 128-bit security. The complete Freescale BeeStack protocol stack includes the following components: * ZigBee Device Objects (ZDO) and ZigBee Device Profile (ZDP) * Application Support Sub-Layer (APS) * Application Framework (AF) * Network (NWK) Layer * Security Service Provider (SSP) * IEEE 802.15.4-compatible MAC and Physical (PHY) Layer NOTE For more details on the ZigBee model and protocol, the user is directed to the ZigBee Specification at www.zigbee.org. In addition to the use of two Stack Profiles, ZigBee also embraces the concept of application profiles. The profiles are intended to assure interoperability between like devices for a specific application from different vendors. The application profile specifies a device description and its messaging protocol such that it defines the type, shape, and features of the network. The ZigBee Alliance defines each profile and targets a specific market. Examples include Smart Energy, Home Automation, Health Care, and Remote Control. Freescale's BeeStack supports a number of these application profiles through demonstration software projects. These projects can be used as a starting point for the user to develop their specific application. For more information on Freescale supported application profiles see AN3403, Freescale IEEE 802.15.4/ZigBee Software Selector Guide. 2.3.4.2 Using BeeStack on the MC1322x Platform When using the BeeStack codebases on the MC1322x platform, the application should be targeted to the proper part number: * MC13224V should be used for ZigBee Profile 1 applications * MC13226V should be used for ZigBee Profile 2 (Pro) applications BeeStack for the MC1322x platform is a single codebase, device selection is determined by a configuration wizard when the BeeKit project is first developed. 2.3.4.3 BeeStack Consumer In response to significant market opportunity in the consumer electronics remote control market, the ZigBee Alliance adapted the ZigBee RF4CE Specification in 2009. Freescale's BeeStack Consumer stack implements the ZigBee RF4CE protocol. It is also a networking layer that sits on top of the IEEE(R) MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 9 802.15.4 MAC. It is designed for standards-based Wireless Personal Area Networks (WPANs) of home entertainment products and conveys information over short distances among the participants in the network. It enables small, power efficient, inexpensive solutions to be implemented for a wide range of applications. Targeted applications include DTV, set top box, A/V receivers, DVD players, security, and other consumer products. Some key characteristics of a BeeStack Consumer network are: * * * * * * * 3 Based on IEEE 802.15.4 Standard Use 3 of the standard 802.15.4 communication channels in the 2.4 GHz band, namely, Channels 15, 20, and 25 2 network node types, controller node and target node Channel Agility mechanism Provides robustness and ease of use Includes essential functionality to build and support a CE network Binaries, and application examples provided High Density, Low Component Count, Integrated IEEE 802.15.4 Solution The MC1322x is more than a high performance, low power platform-in-a-package IEEE 802.15.4 solution. Not only are the transceiver (radio) and MCU on an SoC, the packaged solution contains a 128 Kbyte serial FLASH memory, onboard bypass capacitors for critical nodes, and RF components that present a single-ended 50- interface for an external antenna. The radio is a full differential design with an on-chip transmit/receive (TX/RX) switch, and the PiP also has an onboard balun for differential to singled-ended conversion. On-chip RF matching is also provided to present the proper impedance to the antenna. To further simplify the application, single crystal operation (optimized for 24 MHz) is supported for full radio and MCU operation. If the default 24 MHz crystal is not used, the device supports 13-26 MHz crystals also. The load capacitance to the crystal oscillator is supplied on-chip to eliminate the need for the otherwise required external capacitors. 3.1 Integrated IEEE 802.15.4 Transceiver (Radio and Modem) The MC1322x IEEE 802.15.4 fully-compliant transceiver provides a complete 2.4 GHz radio with 250 kbps Offset-Quadrature Phase Shift Keying (O-QPSK) data in 5.0 MHz channels and full spread-spectrum encode and decode. The modem supports transmit, receive, clear channel assessment (CCA), Energy Detect (ED), and Link Quality Indication (LQI) as required by the 802.15.4 Standard. 3.1.1 RF Interface and Usage The MC1322x RF interface provides for a single-ended, 50- port that connects directly to an antenna. There is an onboard balun that converts the single-ended interface to a full differential, bi-directional, on-chip interface with transmit/receive switch, LNA, and complementary PA outputs. The required port MC1322x Technical Data, Rev. 1.3 10 Freescale Semiconductor impedance matching is also onboard. This combination allows for a very small footprint and a very low cost RF solution. The MC1322x also provides a secondary set of complementary PA outputs that can be used with external RF circuitry such as a additional PA for higher TX power to the antenna. The single-ended port continues as the receive input for this circuit configuration. The receiver demodulator includes a module called the Differential Chip Detector which has two modes of operation: * Non-coherent Detection (NCD) with automatic frequency control (AFC) * Non-coherent Differential Chip Detection (DCD) without AFC The IEEE 802.15.4 standard allows a maximum clock drift of 40 ppm (which equals 80 ppm station-to-station). The MC1322x 802.15.4 demodulator includes two different methods of operating in the presence of such large frequency errors: NCD Mode Provides an increased ~3.5 dB of sensitivity. However, the addition of the AFC increases the demodulator current drain about 3 mA. Default receive mode at lower current. DCD Mode For longer range applications where external amplification may be desired (LNA and/or PA), additional ports are provided for secondary complementary PA outputs. These can be used as a separate PA interface while the single-ended port through the balun is used as an input only. Also, four control pins and a regulated 20mA voltage source are provided to control external components and supply power to the PA outputs. The RF Interface functionality can be summarized as follows: * Programmable output power -- 0 dBm nominal output power, programmable from -30 to +4 dBm * Receive sensitivity (at 1% PER, 20-byte packet) -- < -96 dBm (typical) DCD receive (well above IEEE 802.15.4 specification of -85 dBm) -- < -100 dBm (typical) NCD receive (higher current) * Single-ended 50- antenna port -- Uses integrated transmit/receive (T/R) switch, LNA, and onboard balun. Impedance matching onboard. * Maximum flexibility -- The optional single-ended port becomes RF input only and a separate set of full differential PA outputs are provided. Separate input and outputs allow for a variety of RF configurations including external LNA and PA for increased range * Four control signals for external RF components such as a LNA or PA * Regulated voltage source for PA biasing and powering external components 3.1.2 Modem The modem supports the full requirement of the IEEE 802.15.4 Standard to transmit and receive data packets. In additional, the mechanism is present to measure received signal level to provide CCA, ED, and LQI as required by the 802.15.4 Standard. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 11 3.2 * * * * High Performance, Low Power 32-Bit ARM7 Processor The ARM7TDMI-S processor is a member of the 32-bit ARM family of general-purpose 32-bit microprocessors that offers high performance with very low-power consumption A three stage instruction pipeline (fetch, decode, execute) increases the speed of the flow of instructions to the processor Data access can be 8-bit bytes, 16-bit half words, or 32-bit words. Words must be aligned to 4-byte boundaries. Half words must be aligned to 2-byte boundaries The ARM7TDMI-S processor supports two instruction sets, the 32-bit ARM instruction set and the 16-bit Thumb instruction set. The Thumb mode incorporates 16-bit instructions for higher code density while retaining all the benefits of a 32-bit architecture, such as the full 32-bit registers, 32-bit operations, and 32-bit memory transfer. The use of the instruction sets can be intermixed for maximizing performance while retaining higher code density Address Incrementer Register Bank 31 x 32-Bit Registers (6 Status Registers) 32 x 8 Multiplier Barrel Shifter 32-Bit Alu Write Data Register WDATA[31:0] B Bus A Bus ALU Bus PC Bus Address Register Incrementer Bus ADDR[31:0] Scan Debug Control Instruction Decoder and Control Logic Instruction Pipeline Read Data Register Thumb Instruction Decoder RDATA[31:0] Figure 3. ARM7TDMI-S 32-Bit CPU Core MC1322x Technical Data, Rev. 1.3 12 Freescale Semiconductor 3.3 Low Power Operation and Power Management The MC1322x is inherently a very low power device, but it also has extensive power management and an onboard buck regulator option to maximize battery life. 3.3.1 Operating Current The MC1322x operating currents are a function of operating mode. There are two basic low power modes of Hibernate and Doze, and both have options of how much RAM contents are retained. The difference between Hibernate and Doze is that Doze mode keeps the primary reference oscillator running. Highest operating current is when the radio is active for transmit or receive. Refer to Section 7.4, "Supply Current Characteristics" for more details and specifications. 3.3.2 Power Management The MC1322x power management is controlled through the Clock and Reset Module (CRM). The CRM is a dedicated module to handle MCU clock, reset, and power management functions which includes control of the power regulators. All these functions have impact on attaining lowest power. 3.3.2.1 CRM Features The CRM features include: * Control of system reset * Control clock gating for power savings * Sleep mode (Hibernate and Doze) management -- Degree of chip power down -- Retention of programmed parameters -- Programmable retention of RAM contents -- Clock management * Wake-up management -- Graceful power-up -- Clock management -- Wake-up via programmable timer or external interrupts. * Wake-up timer -- Hibernate mode - based on onboard 2 kHz oscillator or optional 32.768 kHz crystal oscillator -- Doze mode - based on main reference oscillator, typically 24 MHz * Controls reference clocks based on default 24 MHz crystal oscillator or optional 13-26 MHz oscillator with PLL (external filter) for 24 MHz frequency synthesis. * MCU watchdog timer (COP) * Software initiated reset * Management control of onboard linear regulators and optional buck regulator MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 13 3.3.2.2 CRM Operation The CRM has primary control of the entire system: * Reset and power up -- After release of the hardware RESETB signal, the CRM will perform a power up sequence of the MCU. The linear regulators and clock sources are managed for a graceful start-up of the MCU and its resources. The radio is not powered until needed * Normal operation of MCU -- The clock management of the MCU and its resources are controlled by the CRM. The processor clock is programmable from low frequencies up to the maximum reference frequency (13-26 MHz optional w/24 MHz standard) to allow the application to trade-off processing speed versus power savings * Sleep modes and recovery -- There are two sleep modes of Hibernate and Doze. The primary difference is that Doze mode keeps the reference oscillator running. Both modes can retain critical programmed parameters and have selectable sizes of RAM retention. Hibernate has lowest power, but Doze allows high accuracy sleep timing. The CRM manages the recovery from low power, similar to power-up from reset, providing regulator and clock management. -- Wake-up can be based on external interrupts through 4 KBI inputs -- Wake-up can be from internal interrupts -- Wake-up can be based on an RTI (wake-up) timer. * The RTI timer has two possible frequency sources that provide a very low power wake-up option from sleep -- One option is an onboard, low accuracy 2 kHz oscillator -- A second option is to add an external 32.768 kHz crystal for the RTI clock source -- A 32-bit timer allows greater than a 36.4 hour wake-up delay with the 32.768 crystal oscillator * Other features of the CRM: -- An optional COP watchdog timer to monitor CPU program activity -- A programmable software reset 3.3.3 Optional Buck Regulator For battery based applications, an optional buck regulator is provided to maximize battery life. Figure 4 shows the configuration of the buck regulator versus the normal connection. An onboard MOSFET is used as a switch with an external 100H inductor and 10F capacitor when the buck regulator is enabled. The buck regulator drops the higher battery voltage to 1.8 - 2.0 Vdc that is applied to the onboard linear regulators. This allows lower net current from the battery to maximize the life of the battery. MC1322x Technical Data, Rev. 1.3 14 Freescale Semiconductor VDD VDD VBATT VBATT COIL_BK D1 DIODE SCHOTTKY L2 NC COIL_BK 100uH LREG_BK_F B LR EG_BK_F B C2 10uF Normal Operation Buck Regulator Enabled Figure 4. Optional Buck Regulator 3.3.4 Battery Voltage Monitor An optional feature of the ADC module is a battery voltage monitor capability. An onboard 1.2 Vdc reference voltage can be sampled by the ADC module. The battery-sourced supply voltage is used as the high reference voltage for the ADC and as the supply voltage lowers due to battery usage, the onboard reference voltage reading will become greater because this fixed voltage is a higher percentage of the reduced supply voltage. Programmable high and low thresholds are provided for an ADC analog sample channel to monitor the reference voltage. This feature can be used as a trigger to provide low battery indication, protection for data that may be lost due to end-of-life for the battery, monitoring charging, and controlling buck regulator operation. 3.4 IEEE 802.15.4 Acceleration Hardware The MC1322x provides acceleration hardware for IEEE 802.15.4 applications and this hardware includes 802.15.4 MAC acceleration and AES encryption/decryption. 3.4.1 802.15.4 MAC Accelerator (MACA) Overview The MC1322x contains a hardware block that provides a low-level MAC and PHY link controller, which together with software running on the ARM core, implements the baseband protocols and other low-level link routine control and link control. Components of the MACA include a sequencer/controller (with timers), TX and RX packet buffers, DMA block, frame check sequence (FCS) generator/checker, and control registers. Figure 5 shows a MACA simplified block diagram. As part of the 802.15.4 protocol, packets are generated and transmitted, packets are received and verified, and channel energy is measured via a clear channel assessment (CCA). Also, combinations or sequences of events are required as part of the protocol such as an ACK response following a received packet. The MACA facilitates these activities via control of the transceiver and off loads the functions from the CPU. A dedicated DMA function moves data between the MACA buffers and RAM on a cycle steal basis and does not require intervention from the CPU. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 15 The MACA is responsible for construction of packets for TX including FCS, and for parsing the received packets. The MACA will also handle ACKs and TxPoll sequences independent of the ARM processor. During TX the MACA will construct the entire packet. This includes preamble and SFD (start of frame delimiter). During receive, the modem will recognize preamble and SFD, then the MACA will begin receiving the packet with the first bit of frame length, and finally, will check the FCS. Sequencer Timers To Transceiver Modem TX Packet Buffer Control Registers DMA To MCU Bus RX Packet Buffer MACA FCS Generator/ Checker Figure 5. MAC Accelerator Simplified Block Diagram 3.4.1.1 MACA Features In order to reduce CPU load, the MACA module has embedded features for controlling parts of the IEEE 802.15.4 PHY and MAC layer requirements. The MACA core features include: * Sequence Manager sequences / auto sequences -- RX only -- TX only -- Automatic acknowledgment frame reception on transmitted packets -- Automatic acknowledgment frame transmission on received packets -- Auto-RX for continuous reception as coordinator -- Auto sequence for transmitted MAC data.request -- Assist for efficient response to MAC data.request -- Embedded channel assessment in sequence -- Support for sequences with slotted mode access -- Timer triggered and immediately executed actions -- Support for extended RX for reception in random backoff and battery life extension -- Support for promiscuous mode * Programmable auto sequence timing - Each CCA, RX, or TX event is an independent operation. The radio gets through a power-up or "warm-up" sequence for each operation (including VCO), and there is also a power-down or "warm-down" time. Sequences are combinations of radio operations and are highly configurable. -- RX warm-up is 72 s MC1322x Technical Data, Rev. 1.3 16 Freescale Semiconductor * * * * * * 3.4.2 -- TX warm-up is 92 s -- Turnaround times - The IEEE 802.15.4 Standard requires a TX-to-RX or a RX-to-TX turnaround time to be less than or equal to 12 symbols times (192 s). - Best practice for maximum station-to-station performance is to minimize TX-to-RX turnaround time and to maximize (within spec) RX-to-TX turnaround time. - Auto sequences should use recommended turnaround times of: a) 11 symbols times (176 s) RX-to-TX b) 96 s TX-to-RX. Dedicated DMA for transfer of TX/RX data from/to RAM (minimum bus clock of 2 MHz for 802.15.4 modem operation) Maskable, event-driven interrupt generation Address header filtering for received packets. A promiscuous mode allows bypass of the filtering for monitoring network traffic Packet manager -- Handles preamble data -- Handles frame check sequence (FCS) a.k.a CRC -- Embedded header filter for received packets Control/status registers mapped into CPU memory map 32-Bit random number generator -- Runs at the bus clock rate, a 32-bit Linear Feedback Shift Register (LFSR) can be set with a seed value and uses a 32-bit primitive polynomial. A 32-bit random number is fetched with every read of the proper control register Advanced Security Module (ASM) The IEEE 802.15.4 Standard and the ZigBee Standard both provide for optional use of data encryption.The ASM engine is a hardware block that accelerates encryption/decryption using the Advanced Encryption Standard (AES). The engine can perform "Counter" (CTR) and Cipher Block Chaining (CBC) encryption. The combination of these two modes of encryption are known as CCM mode encryption. CCM is short for Counter with CBC-MAC. CCM is a generic authenticate and encrypt block cipher mode. CCM is only defined for use with 128 bit block ciphers, such as AES. The definition of CCM mode encryption is documented in the NIST publication SP800-38C. The ASM has the following features: * 32-Bit wide bus interface * CTR encryption in 13 clock cycles * CBC encryption in 13 clock cycles * Encrypts 128 bits as a unit * The 128-bit registers are aligned on quad word boundaries (16 byte) * Self-test mode * Maskable "action complete" interrupt MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 17 4 Memory The MC1322x memory resources consist of RAM, ROM, and serial FLASH. 4.1 RAM and ROM The RAM and ROM features include: * 96 Kbytes RAM. -- RAM0: 8 Kbytes, 2 Kwords (2048 x 32 bits) -- RAM1: 24 Kbytes, 6 Kwords (6144 x 32 bits) -- RAM2: 32 Kbytes, 8 Kwords (8192 x 32 bits) -- RAM3: 32 Kbytes, 8 Kwords (8192 x 32 bits) * All read or write accesses require a minimum of two system clock cycles * Stall signal generated for read after write cycles * Clock is enabled only on the accessed memory device for low power consumption * RAMs have been divided to allow for power savings. While sleeping, the above RAM blocks can be turned off (combinations include 8, 32, 64, and 96 Kbytes active) and the RAM remainder can be placed in a low voltage mode for data retention. If more RAMs are turned on, then less battery life will be achieved. Depending on the amount of RAM powered during sleep, the boot time may be longer with less RAM as the non-powered RAM must be reloaded from FLASH. * 80 Kbytes ROM -- 20 Kwords (20480 x 32 bits) -- Initially contains bootstrap code, 802.15.4 MAC and drivers. The MAC software builds on the lower level hardware capability of the transceiver and MACA. All code except the bootstrap is "patchable". 4.2 Serial FLASH (NVM) The MC1322x also contains a 128 Kbyte serial FLASH memory that can be mirrored into the 96 Kbyte RAM. The serial FLASH is accessed via an internal dedicated SPI module (SPIF). The FLASH erase, program, and read capability are programmed through the SPIF port. The FLASH is accessed at boot time to load/initialize RAM. All actual CPU program and data access is from RAM or ROM. MC1322x Technical Data, Rev. 1.3 18 Freescale Semiconductor 5 MCU Peripherals The MC1322x has a rich set of MCU peripherals. Figure 6 shows the peripheral modules. BATTERY DETECT DUAL 1 2 -B IT ADC M O DULE T IM E R M O DULE (T M R ) (4 T m r B lo c k s ) UART M O DULE (U A R T 0 ) JTAG / N e xu s DEBUG UART M O DULE (U A R T 1 ) ARM7 T D M I-S 3 2 -B IT CPU S Y N C S E R IA L IN T E R F A C E (S S I/i2 S ) BUS IN T E R F A C E & MEMORY A R B IT R A T O R ARM IN T E R R U P T CO NTRO LLER (A IT C ) KEYBOARD IN T E R F A C E (K B I) UP TO 64 IO PINS F ro m CRM IN T E R -IC B U S M O DULE (I2 C ) S E R IA L P E R IP H E R A L IN T E R F A C E (S P I) G P IO a n d IO CO NTRO L SPI FLASH M O DULE (S P IF ) Figure 6. MCU Peripherals MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 19 5.1 Parallel IO (GPIO) The parallel I/O features include: * A total of 64 general-purpose I/O pins * Individual control (direction and output state) for each pin when in GPIO mode * Pad hysteresis enables * Software-controlled pull-ups/pull-downs on each input pin * When not used as GPIO, the IO provide alternative functions -- Debug ports for JTAG (four signals) and Nexus (fourteen signals) modules -- Four control signals for external RF components such as an LNA, PA, and antenna switch -- Eight analog inputs for ADC input channels -- Four signals for ADC reference voltages -- Eight signals for UART1 and UART2 -- Two I2C signals -- Four timer block signals -- Four SPI block signals -- Four SSI block signals -- Eight KBI signals * Eight KBI pins are kept alive during Hibernate or Doze. Four KBI are output and four are inputs. The input can be used as wake-up interrupts 5.2 Keyboard Interface (KBI) The MC1322x designates 8 pins (KBI_0 to KBI_7) as a keyboard interface, where four of these signals typically are outputs and four are inputs (KBI_4 to KBI_7) that support interrupts. These 8 pins could typically be used as a matrix interface to support up to 16 switches or buttons, such as a keypad. These signals can also be used as general purpose IO if a keyboard is not present. During Hibernate or Doze, the KBI are unique in that they are kept alive. Four KBI are outputs and four KBI are inputs. The inputs can be enabled as asynchronous interrupts to wake-up the MC1322x from the sleep mode. MC1322x Technical Data, Rev. 1.3 20 Freescale Semiconductor 5.3 Timer (TMR) Module The MC1322x provides a timer module (TMR) that contains four identical counter/timer groups. Each group is capable of many variants of input capture, output compare and pulse-width modulation. The wide range of operational modes is useful for many control and sensor applications. Figure 7 shows a block diagram of an individual timer group. CMPLD1 COMP1 Comparator M U X CMPLD2 COMP2 MCU DATA BUS LOAD COUNTER OFLAG Output Comparator HOLD CAPTURE Other Counter Reference Peripheral Reference Clock External M U X Prescaler STATUS AND CONTROL Figure 7. Timer Group Block Diagram Each 16-bit counter/timer group contains a prescaler, a counter, a load register, a hold register, a capture register, two compare registers, and status and control registers. * Load Register -- Provides the initialization value to the counter when the counter's terminal value has been reached * Hold Register -- Captures the counter's value when other counters are being read. This feature supports the reading of cascaded counters * Capture Register -- Enables an external signal to take a snap shot of the counter's current value * COMP1 and COMP2 Registers -- Provides the values to which the counter is compared. If a match occurs, the OFLAG signal can be set, cleared, or toggled. At match time, an interrupt is generated (if enabled), and the new compare value is loaded into the COMP1 or COMP2 registers from CMPLD1 and CMPLD2 if enabled * The Prescaler provides different time bases useful for clocking the counter/timer MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 21 * * The Counter provides the ability to count internal or external events Control and Status Registers -- Provides operational mode control of the counter, status, clock source control, interrupt control, and external interface control Four GPIO pins (TMR0 -TMR3) are programmable and can be used with any counter/timer group. The TMR module feature include: * Four 16-bit counters/timers groups * Up/down count * Counters are cascadable for up to 64-bit delay counter * Programmable count modulo. * Peripheral reference clock is same as bus clock * External clock max count rate equals peripheral clock divided by 2 * Internal clock max count rate equals peripheral clock. * Count once or repeatedly * Counters are preloadable * Compare registers are preloadable * Counters share available four GPIO pins (programmable as inputs or outputs and programmable for falling or rising edge) * Separate prescaler for each counter * Each counter has capture and compare capability * Optional input glitch filter * Functional modes include stop, count, edge-count, gated-count, quadrature-count, signed-count, triggered-count, one-shot, cascade-count, pulse-output, fixed frequency PWM, and variable-frequency PWM 5.4 UART Modules The MC1322x has two universal asynchronous receiver/transmitter (UART) modules. Each UART has an independent fractional divider, baud rate generator that is clocked by the peripheral bus clock (typically 24 MHz) which enables a broad range of baud rates up to 1,843.2 kbaud. Transmit and receive use a common baud rate for each module. Each UART provides the following features: * 8-bit only data * One or two stop bits * Programmable parity (even, odd, and none) * Full duplex four-wire serial interface (RXD, TXD, RTS, and CTS) * Hardware flow control support for RTS and CTS signals * 32-byte receive FIFO and 32-byte transmit FIFO * Programmable sense for RTS/CTS pins (high true/low true) MC1322x Technical Data, Rev. 1.3 22 Freescale Semiconductor * * * * * * * * 5.5 Status flags for various flow control and FIFO states Receiver detects framing errors, start bit error, break characters, parity errors, and overrun errors. Voting logic for improved noise immunity (16X/8X oversampling) Maskable interrupt request Time-out counter, which times out after eight non-present characters Receiver and transmitter enable/disable Low-power modes Baud rate generator to provide any multiple-of-2 baud rate between 1.2 kbaud and 1,843.2 kbaud Inter-Integrated Circuit (I2C) Module The MC1322x provides an Inter-Integrated Circuit (I2C) module for the I2C which is a two-wire, serial data (SDA) and serial clock (SCL), bidirectional serial bus. The I2C allows for data exchange between the MC1322x and other devices such as MCUs, serial EEPROM, serial ADC and DAC devices, and LCDs. The I2C minimizes interconnections between devices and is a synchronous, multi-master bus that allows additional devices to be connected and still handle system expansion and development. The bus includes collision detection and arbitration to prevent data corruption if two or more masters attempt to simultaneously control the I2C. The I2C module is driven by the peripheral bus clock (typically 24 MHz) and the SCL bit clock is generated from a prescaler. The prescaler divide ratio can be programmed from 61,440 to 160 (decimal) which gives a maximum bit clock of 150 kbps. The I2C module supports the following features: * * * * * * * * * * * Two-wire (SDA and SCL) interface Multi-master operation Master or slave mode Arbitration lost interrupt with automatic mode switching from master to slave Calling address identification interrupt START and STOP signal generation/detection Acknowledge bit generation/detection Bus busy detection Software-programmable bit clock frequency up to 150 kbps Software-selectable acknowledge bit On-chip filtering for spikes on the bus MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 23 5.6 Serial Peripheral Interface (SPI) Modules The MC1322x has two SPI modules that use a common architecture 5.6.1 External SPI Module The MC1322x offers a dedicated Serial Peripheral Interface (SPI) module for external use. The SPI is a high-speed synchronous serial data input/output port used for interfacing with serial memories, peripheral devices, or other processors. The SPI allows a serial bit stream of a programmed length (1 to 32 bits) to be shifted simultaneously into and out of the device at a programmed bit-transfer rate (called 4-wire mode). There are four pins associated with the SPI port (SPI_SCK, SPI_MOSI, SPI_MISO, and SPI_SS). The SPI module can be programmed for master or slave operation. It also supports a 3-wire mode where for master mode the MOSI becomes MOMI, a bidirectional data pin, and for slave mode the MISO becomes SISO, a bidirectional data pin. In 3-wire mode, data is only transferred in one direction at a time. The SPI bit clock is derived from the peripheral reference clock (typically 24 MHz with a maximum of 26 MHz). A prescaler divides the peripheral reference clock with a programmed divide ratio from 2 to 256. Typical bit clock range will be from 12 MHz to 93.75 kHz. The SPI has the following features: * Master or slave mode operation * Data buffer is 4 bytes (32 bits) in length * SPI transfer length programmable from 1 to 32 bits * MSB-first shifting * Programmable transmit bit rate (typically 12 MHz max) * Serial clock phase and polarity options * Full-duplex (4-wire) or bidirectional data (3-wire) operation * SPI transaction can be polled or interrupt driven * Slave select signal * Low Power (SPI Master uses gated clocks. SPI Slave clock derived completely from SPI_SCK.) 5.6.2 SPI FLASH Module (SPIF) The SPIF is an internal SPI block dedicated to control, reading, and writing of the serial FLASH memory (NVM). It uses the same architecture as the general SPI block, but is limited by the characteristics of the FLASH SPI interface. MC1322x Technical Data, Rev. 1.3 24 Freescale Semiconductor 5.7 Synchronous Serial Interface (SSI) Module The MC1322x provides a versatile Synchronous Serial Interface (SSI) which is a full-duplex, serial port that allows communication with a variety of serial devices. These serial devices can be digital signal processors (DSPs), MCUs, peripherals, popular industry audio CODECs, and devices that implement the Inter-Integrated Circuit sound bus standard (I2S). The SSI typically transfers samples in a periodic manner and it consists of independent transmitter and receiver sections with common clock generation and frame synchronization. The external signals include the bit clock (SSI_BITCK), frame sync (SSI_FSYN), RX data (SSI_RX), and TX data (SSI_TX). The SSI has the following basic operating modes all with synchronous protocol: * Normal mode -- The simplest SSI mode transfers data in one time slot per frame * Network mode -- Creates a Time Division Multiplexed (TDM) network, such as a TDM CODEC network or a network of DSPs * Gated Clock mode -- Connects to SPI-type interfaces on MCUs or external peripheral chips With its multi-modes, the SSI can be programmed for two very useful functions: * A second SPI port augmenting the MC1322x SPI module * I2S interface - the SSI is capable of generating the required clock frequencies and data format to drive a serial stereo audio DAC The SSI includes the following features: * Synchronous transmit and receive sections with shared internal/external clocks and frame syncs, operating in Master or Slave mode. * Normal mode operation using frame sync * Network mode operation allowing multiple devices to share the port with as many as thirty-two time slots * Gated Clock mode operation requiring no frame sync * SSI clock source is Peripheral Clock (typically 24 MHz); maximum SSI transfer rate is 6.0 MHz * Separate Transmit and Receive FIFOs. Each of which is 8x24 bits * Programmable data interface modes including I2S, LSB, MSB aligned * Programmable word length (8, 10, 12, 16, 18, 20, 22 or 24 bits) * Program options for frame sync and clock generation * Programmable I2S modes (Master, Slave) * Programmable internal clock divider * Time Slot Mask Registers for reduced CPU overhead (for Tx and Rx both) * SSI power-down feature MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 25 5.8 Analog-to-Digital Converter (ADC) Module The MC1322x ADC module provides two 12-bit analog-to-digital converters (ADC_1 and ADC_2) with eight external channels (ADC7 - ADC0) that can be multiplexed to either ADC. ADC_1 can also sample a battery reference voltage for monitoring purposes. External pins (ADC2_VREFH, ADC2_VREFL, ADC1_VREFH, and ADC1_VREFL) are provided for independent ADC reference voltages. The minimum sample time is 20 s. Figure 8 shows a block diagram of the ADC module. Each ADC can be programmed to scan multiple selected channels on a timed basis. The primary clock to the ADC module is the peripheral reference clock (typically 24 MHz). For the time period between scan sequences, the primary clock is first divided by an 8-bit prescale (1-255), and the derived clock drives both the 32-bit delay timer and the ADC sequencer. Each ADC has its own delay timer and sequencer. Once a scan sequence has been initiated, all selected channels can be sampled. Registers are provided to define thresholds that can be enabled for the sampled channels. A threshold can be assigned to a specific channel and can be programmed to be a less-than or greater-than threshold. Multiple thresholds can be assigned to a single channel. Warm-up of the analog portion of the ADC circuitry is provided for power management, and a separate 300 kHz ADC clock must be programmed via its own divider. The battery monitor has two (2) dedicated threshold registers to set the high and low limits of the battery sample channel. Sample values are stored in a 8x16-bit FIFO. The FIFO accumulates samples from both ADCs, and the 12-bit sample value and a 4-bit channel tag are saved for each sample. The FIFO is read by the CPU from a register address. The module can be programmed to interrupt the processor based on the timed sample activity. Sample activity, sequencer activity, or FIFO "fullness" can all be enabled to generate an interrupt. The ADCs can also be overridden to sample on command as opposed to sequencer, time-based activity. C o ntrol O verride M o de 32-B it T im er S equ encer 1 M U X A D C 1 M ux S el A D C 1 E nable M U X A D C _1 C om pare MCU D A TA BUS F IFO (8 x 16-B it, 12-bit valu e + 4b it channel Tag) ADC Clock C ontro l R eg isters B attery M U X A D C _2 P rescaler 32-B it Tim er D ivider P eripheral R eference C lock S equ encer 2 M U X A D C 2 E nable A D C 2 M ux S el ADC Clock C o ntrol O verride M o de A n alog C h ann els ADC0 - ADC7 A nalog 300 kH z Figure 8. ADC Module Block Diagram MC1322x Technical Data, Rev. 1.3 26 Freescale Semiconductor The ADC module has the following features: * 12 bit resolution. Effective number of bits 8-9 * Valid usable input voltage range: [Vref_high-0.2V] to [Vref_low+0.2V] * Maximum input range: VBATT to VSS * Minimum sample time 20 s * Peripheral Clock (set by CRM) uses an 8-bit prescaler to provide the time base for the module * Two independent channels, each with a 32-bit timer * ADC_1 has 9 channels: 8 external analog inputs plus battery reference voltage * ADC_2 has 8 channels: 8 external analog inputs * Active channels for each ADC are programmable * Eight active monitors plus battery reference monitors can generate a IRQ * An 8-deep FIFO for recording data * IRQs can be generated by the channel compare values, FIFO status, and sequencers MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 27 Pin Assignments and Connections ADC2_VREFH ADC1_VREFH ADC1_VREFL ADC2_VERFL RF_RX_TX RX_ON RF_GND ANT_2 ANT_1 RF_BIAS PA_POS PA_NEG TX_ON RESETB XTAL_24_IN XTAL_24_OUT 6 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 Substrate GND Pads 49 48 47 2 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 98 100 101 102 103 104 105 106 107 108 109 46 3 4 45 5 44 6 43 7 42 8 41 40 9 10 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 39 11 38 37 12 13 36 35 14 34 15 16 17 Active Signal Pads 18 19 20 21 22 23 24 25 26 27 28 29 30 31 33 32 UART1_RTS UART1_CTS UART1_RX UART1_TX I2C_SDA I2C_SCL TMR3 TMR2 TMR1 TMR0 SPI_SCK SPI_MOSI SPI_MISO SPI_SS SSI_BITCK SSI_FSYN ADC0 ADC1 ADC2 ADC3 ADC4 ADC5 ADC6 ADC7_RTCK TDO TDI TCK TMS UART2_RTS UART2_CTS UART2_RX UART2_TX 1 XTAL_32_OUT XTAL_32_IN RF_PLL_FLT VBATT LREG_BK_FB COIL_BK KBI_0_HST_WK KBI_1 KBI_2 KBI_3 KBI_4 KBI_5 KBI_6 KBI_7 SSI_TX SSI_RX MC1322x Notes: 1. Bottom pads 75-79, 84-88, 93-97, 104-106, and 115 are Substrate Ground. 2. Bottom pads 102-103, 111-114, 120-124, and 129-133 are active pads. 3. All remaining bottom pads are isolated from ground (NC), and are provided here for mechanical strength. 4. Figure 15 (Mechanical Diagram), is the bottom view, not the top view as shown here. Figure 9. MC1322x Pinout (Top View: Bottom Pads Shown) MC1322x Technical Data, Rev. 1.3 28 Freescale Semiconductor 6.1 Pin Definitions Table 2 details the MC1322x pinout and functionality. Table 2. Pin Function Description Pin # Pin Name Type Description1 Functionality 1 ADC0 Analog Input or Digital Input/Output ADC analog input Channel 0 / GPIO30 ADC sample channel can be used by either ADC_1 or ADC_2. 2 ADC1 Analog Input or Digital Input/Output ADC analog input Channel 1/ GPIO31 ADC sample channel can be used by either ADC_1 or ADC_2. 3 ADC2 Analog Input or Digital Input/Output ADC analog input Channel 2/ GPIO32 ADC sample channel can be used by either ADC_1 or ADC_2. 4 ADC3 Analog Input or Digital Input/Output ADC analog input Channel 3/ GPIO33 ADC sample channel can be used by either ADC_1 or ADC_2. 5 ADC4 Analog Input or Digital Input/Output ADC analog input Channel 4/ GPIO34 ADC sample channel can be used by either ADC_1 or ADC_2. 6 ADC5 Analog Input or Digital Input/Output ADC analog input Channel 5/ GPIO35 ADC sample channel can be used by either ADC_1 or ADC_2. 7 ADC6 Analog Input or Digital Input/Output ADC analog input Channel 6/ GPIO36 ADC sample channel can be used by either ADC_1 or ADC_2. 8 ADC7_RTCK Analog Input or Digital Input/Output ADC analog input Channel 7 / ReTurn ClocK / GPIO37 ADC sample channel can be used by either ADC_1 or ADC_2. Alternately, the signal returns TCK for JTAG to support adaptive clocking. 9 TDO Digital Input/Output JTAG Test Data Output / GPIO49 JTAG debug port serial data output. 10 TDI Digital Input/Output JTAG Test Data Input / GPIO48 JTAG debug port serial data input. 11 TCK Digital Input/Output JTAG Test Clock Input / GPIO47 JTAG debug port clock input. 12 TMS Digital Input/Output JTAG Test Mode Select Input / GPIO46 13 UART2_RTS Digital Input/Output UART2 Request to Send input / UART2 RTS control input. GPIO21 14 UART2_CTS Digital Input/Output UART2 Clear to Send output / GPIO20 15 UART2_RX Digital Input/Output UART2 RX data input / GPIO19 UART2 receive data input. JTAG debug port test mode select input. UART2 CTS control output. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 29 Table 2. Pin Function Description (continued) Pin # Pin Name Type Description1 Functionality 16 UART2_TX Digital Input/Output UART2 TX data output / GPIO18 UART2 transmit data output. 17 UART1_RTS Digital Input/Output UART1 Request to Send input / UART1 RTS control input. GPIO17 18 UART1_CTS Digital Input/Output UART1 Clear to Send output / GPIO16 19 UART1_RX Digital Input/Output UART1 RX data input / GPIO15 UART1 receive data input. 20 UART1_TX Digital Input/Output UART1 TX data output / GPIO14 UART1 transmit data output. 21 I2C_SDA Digital Input/Output I2C Bus data / GPIO13 I2C bus signal SDA 22 I2C_SCL Digital Input/Output I2C Bus clock / GPIO12 I2C bus signal SCL 23 TMR3 Digital Input/Output Timer 3 IO signal / GPIO11 Pin is used as counter output or counter input clock. 24 TMR2 Digital Input/Output Timer 2 IO signal / GPIO10 Pin is used as counter output or counter input clock. 25 TMR1 Digital Input/Output Timer 1 IO signal / GPIO9 Pin is used as counter output or counter input clock. 26 TMR0 Digital Input/Output Timer 0 IO signal / GPIO8 Pin is used as counter output or counter input clock. 27 SPI_SCK Digital Input/Output SPI Port clock / GPIO7 SPI port clock. 28 SPI_MOSI Digital Input/Output SPI Port MOSI/ GPIO6 SPI Port Master Out Slave In (MOSI) data signal. 29 SPI_MISO Digital Input/Output SPI Port MISO / GPIO5 SPI Port Master In Slave Out (MISO) data signal. 30 SPI_SS Digital Input/Output SPI Port SS / GPIO4 SPI Port Slave Select (SS) signal. 31 SSI_BITCK Digital Input/Output SSI Bit Clock / GPIO3 SSI serial TX/RX clock and is bi-directional. 32 SSI_FSYN Digital Input/Output SSI Frame Sync / GPIO2 SSI frame sync for data (RX or TX) and is bi-directional. 33 SSI_RX Digital Input/Output SSI RX data input / GPIO1 SSI serial RX data input. 34 SSI_TX Digital Input/Output SSI TX data output / GPIO0 SSI serial TX data output. 35 KBI_7 Digital Input/Output Keyboard Interface Bit 7 / GPIO29 Asynchronous interrupt input. UART1 CTS control output. MC1322x Technical Data, Rev. 1.3 30 Freescale Semiconductor Table 2. Pin Function Description (continued) Pin # Pin Name Type Description1 Functionality 36 KBI_6 Digital Input/Output Keyboard Interface Bit 6 / GPIO28 Asynchronous interrupt input. 37 KBI_5 Digital Input/Output Keyboard Interface Bit 5 / GPIO27 Asynchronous interrupt input. 38 KBI_4 Digital Input/Output Keyboard Interface Bit 4 / GPIO26 Asynchronous interrupt input. 39 KBI_3 Digital Input/Output Keyboard Interface Bit 3 / GPIO25 Used as output for keyboard interface. 40 KBI_2 Digital Input/Output Keyboard Interface Bit 2 / GPIO24 Used as output for keyboard interface. 41 KBI_1 Digital Input/Output Keyboard Interface Bit 1 / GPIO23 Used as output for keyboard interface. 42 KBI_0_HST_WK Digital Input/Output Keyboard Interface Bit 0 / HoST Used as output for keyboard interface / Walk-up output / GPIO22 Alternative function as a wake-up output (based on a timer) to external device. 43 COIL_BK Power Switch Output Buck converter coil drive output Onboard buck converter connection to external coil, driven by onboard MOSFET. 44 LREG_BK_FB Power Input Voltage input to onboard regulators, buck regulator feedback voltage 45 VBATT Power Input High side supply voltage to buck Connect to battery. regulator switching MOSFET and IO buffers 46 RF_PLL_FLT Analog Voltage PLL filter connection * Connection for PLL filter (Type 2, 2nd Order) when using primary crystal with frequency other than 24 MHz (13-26 MHz). * No Connect for 24 MHz crystal. 47 XTAL_32_IN Analog Input Optional 32.768 kHz crystal oscillator input Connect to 32.768 kHz crystal 48 XTAL_32_OUT Analog Output Optional 32.768 kHz crystal oscillator output Connect to 32.768 kHz crystal 49 XTAL_24_OUT Analog Output Primary 24 MHz crystal oscillator output * Connect to 13-26 MHz crystal (24 MHz default). * No load capacitor required * Do not load with any capacitance. 50 XTAL_24_IN Analog Input Primary 24 MHz crystal oscillator input * Connect to 13-26 MHz crystal (24 MHz default). * No load capacitor required * Do not load with any capacitance. 51 RESETB Digital Input System reset input Active low, asynchronous reset 52 TX_ON Digital Input/Output Control output for external RF component / GPIO44 Programmable control pin * When using onboard buck converter, connect to load side of coil. * When not using buck converter, connect to VBATT. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 31 Table 2. Pin Function Description (continued) Pin # Pin Name Type Description1 Functionality 53 PA_NEG RF Output RF power amplifier (PA) ouput negative * Open drain. Must be connected to RF_BIAS through a bias network. * Only used for external dual port operation. * Do not use for single port operation. No Connect. 54 PA_POS RF Output RF power amplifier (PA) ouput positive * Open drain. Must be connected to RF_BIAS through a bias network. * Only used for external dual port operation. * Do not use for single port operation. No Connect. 55 RF_BIAS Analog Power Analog VDD regulator output Output 1.5 Vdc voltage regulated output used to supply differential PA output port. When using dual port operation, tie to PA_POS and PA_NEG through bias networks. 56 ANT_1 Digital input / Output Control output for external RF component / GPIO42 Programmable control pin. 57 ANT_2 Digital input / Output Control output for external RF component / GPIO43 Programmable control pin. 58 RF_GND Power Input RF ground. Connect to ground VSS. 59 RX_ON Digital input / Output Control output for external RF component / GPIO45 Programmable control pin. 60 RF_RX_TX RF Input/Output RF single-ended, single port input and ouput * Interfaces to onboard balun. 50 impedance * Full bidirectional port with onboard T/R switch. * Used as single-ended RF input port for dual port operation with PA_NEG and PA_POS PA outputs. 61 ADC2_VREFL Analog Input Low reference voltage for or Digital Input ADC_2 / GPIO39 / Output VREFL for ADC_2. 62 ADC1_VREFL Analog Input Low reference voltage for or Digital Input ADC_1 / GPIO41 / Output VREFL for ADC_1. 63 ADC1_VREFH Analog Input High reference voltage for or Digital Input ADC_1 / GPIO40 / Output VREFH for ADC_1. 64 ADC2_VREFH Analog Input Low reference voltage for or Digital Input ADC_2 / GPIO38 / Output VREFH for ADC_2. 75-79 VSS Power input External package GND pads. Common VSS. Connect to ground. 84-88 VSS Power input External package GND pads. Common VSS. Connect to ground. MC1322x Technical Data, Rev. 1.3 32 Freescale Semiconductor Table 2. Pin Function Description (continued) Pin # 93-97 Pin Name Type Description1 Functionality VSS Power input External package GND pads. Common VSS. Connect to ground. 102 MDO01 Digital Input/Output Message Data Out Bit 1 output / Nexus debug port message data output Bit 1. GPIO52 103 MDO00 Digital Input/Output Message Data Out Bit 0 output / Nexus debug port message data output Bit 0. GPIO51 104106 VSS Power input External package GND pads. Common VSS. 111 MDO03 Digital Input/Output Message Data Out Bit 3 output / Nexus debug port message data output Bit 3. GPIO54 112 MDO02 Digital Input/Output Message Data Out Bit 2 output / Nexus debug port message data output Bit 2. GPIO53 113 MSEO1_B Digital Input/Output Message Start / End Out Bit 1 output / GPIO60 Nexus debug port message start / end output Bit 1. Signal is active low. 114 MSEO0_B Digital Input/Output Message Start / End Out Bit 0 output / GPIO59 Nexus debug port message start / end output Bit 0. Signal is active low. 115 VSS Power input External package GND pads. Common VSS. Connect to ground. 120 MDO05 Digital Input/Output Message Data Out Bit 5 output / Nexus debug port message data output Bit 5. GPIO56 121 MDO04 Digital Input/Output Message Data Out Bit 4 output / Nexus debug port message data output Bit 4. GPIO55 122 RDY_B Digital Input/Output Ready output / GPIO61 Nexus debug port ready output. Signal is active low. 123 EVTO_B Digital Input/Output Event Out output / GPIO62 Nexus debug port event out output. Signal is active low. 124 DIG_REG Digital Power Output Digital core logic VDD supply. 1.2 Vdc internally regulated VDD supply to digital logic core. No Connect,. For test only 129 MDO07 Digital Input/Output Message Data Out Bit 7 output / Nexus debug port message data output Bit 7. GPIO58 130 MDO06 Digital Input/Output Message Data Out Bit 6 output / Nexus debug port message data output Bit 6. GPIO57 131 MCKO Digital Input/Output Message Clock Out output / GPIO50 Nexus debug port message clock output. 132 EVTI_B Digital Input/Output Event In input / GPIO63 Nexus debug port event in input. Signal is active low. Connect to ground. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 33 Table 2. Pin Function Description (continued) Pin # 133 Pin Name NVM_REG NVM Power Output 65-74 NC 80-83 89-92 98-101 107-110 116-119 125-128 134-145 1 Description1 Type Functionality FLASH (NVM) VDD supply. VDD supply to FLASH. Typically No Connect. Can be connected to VDD when regulated 1.8Vdc mode is used. No Connect These pads are provided for extra mechanical attach strength to meet demanding requirements of drop tests. Pins described as GPIO have an alternative general purpose I/O function. 6.2 Hardware Development Interface Interconnects The MC1322x supports two development hardware interfaces. 6.2.1 ARM JTAG Interface Connector The MC1322x supports connection to a subset of the defined ARM JTAG connector. The JTAG hardware interface uses a 20-pin header with a standard 0.1 inch spacing. Table 3 shows how the MC1322x pins are connected to the associated JTAG header pinouts if the JTAG connector is provided on the application. Table 3. ARM JTAG 20-Pin Connector Assignments Name1 Pin # Pin # Name VBATT 1 2 VBATT NC2 3 4 GND TDI 5 6 GND TMS 7 8 GND TCK 9 10 GND RTCK 11 12 GND TDO 13 14 GND RESET3 15 16 GND NC 17 18 GND NC 19 20 GND 1 NC = No Connect. MC1322x does not support separate JTAG reset TRST. 3 VBATT through a 100k- pullup. 2 MC1322x Technical Data, Rev. 1.3 34 Freescale Semiconductor 6.2.2 Nexus Mictor Interface Connector The MC1322x also supports connection to a subset of the defined Nexus Mictor connector. The hardware interface is a 38-pin Mictor target connector. Table 4 shows the device pins that are connected to the associated Mictor pin outs if the Mictor connector is used. Table 4. Nexus 38-Pin Mictor Connector Assignments Name1 Pin # Pin # Name NC 1 2 NC NC 3 4 NC NC 5 6 RTCK NC 7 8 NC VBATT(pullup)2 9 10 EVTI_B TDO 11 12 VBATT3 NC 13 14 RDY_B TCK 15 16 MDO07 TMS 17 18 MDO06 TDI 19 20 MDO05 RESET4 21 22 MDO04 NC 23 24 MDO03 NC 25 26 MDO02 NC 27 28 MDO01 NC 29 30 MDO00 NC 31 32 EVTO_B NC 33 34 MCKO NC 35 36 MSEO1_B NC 37 38 MSEO0_B 1 NC means No Connect. VBATT through a 100k- pullup. 3 VBATT isolated by a 1k- resistor. 4 VBATT through a 100k- pullup. 2 MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 35 7 System Electrical Specification This section details maximum ratings for the 99-pin LGA package and recommended operating conditions, DC characteristics, and AC characteristics. 7.1 LGA Package Maximum Ratings Absolute maximum ratings are stress ratings only, and functional operation at the maximum rating is not guaranteed. Stress beyond the limits specified in Table 5 may affect device reliability or cause permanent damage to the device. For functional operating conditions, refer to the remaining tables in this section. This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for instance, either VSS or VBATT) or the programmable pull-up resistor associated with the pin is enabled. Table 5 shows the maximum ratings for the 99-Pin LGA package. Table 5. LGA Package Maximum Ratings Rating Symbol Value Unit Maximum Junction Temperature TJ 125 C Storage Temperature Range Tstg -55 to 125 C Moisture Sensitivity Level MSL3-260 260 C VBATT, VDDINT -0.3 to 3.7 Vdc Vin -0.3 to (VDDINT + 0.2) Vdc Pmax 10 dBm Reflow Soldering Temperature (for reflow soldering profile and other LGA module reference information, see Freescale Application Note, AN3311) Power Supply Voltage Digital Input Voltage RF Input Power Note: Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the limits in the Electrical Characteristics or Recommended Operating Conditions tables. Note: Meets Human Body Model (HBM) = 2 kV. RF input/output pins have no ESD protection. MC1322x Technical Data, Rev. 1.3 36 Freescale Semiconductor 7.2 Recommended Operating Conditions Table 6. Recommended Operating Conditions Characteristic Symbol Min Typ Max Unit VDD 2.0 - 3.6 Vdc 2.1 - 3.6 Vdc Power Supply Operating Voltage Single un-regulated source (VBATT and LREG_BK_FB tied common to VDD) Onboard buck with un-regulated source (VBATT tied to VDD) Input Frequency fin 2.405 - 2.480 GHz Operating Temperature Range TA -40 25 +105 C Logic Input Voltage Low VIL 0 - 30% VBATT V Logic Input Voltage High VIH 70% VBATT - VBATT V Pmax - - 10 dBm fref 13 24 26 MHz RF Input Power Crystal Reference Oscillator Frequency (40 ppm over operating conditions to meet the 802.15.4 standard.) 7.3 DC Electrical Characteristics Table 7. DC Electrical Characteristics (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, unless otherwise noted) Characteristic Symbol Min Typ Max Unit Power Supply Voltage1 (voltage applied to power input pins; VBATT (pin 45), LREG_BK_FB (pin 44)) VDD 2.0 2.7 3.6 Vdc High impedance (off-state) leakage current (per pin) (VIn = VDD or VSS, all input/outputs, device must not be in low power mode) |IOZ| - - 1.0 Input Current (VIN = 0 V or VDDINT) (VIn = VDD or VSS, all input/outputs, device must not be in low power mode) IIN - - 1.0 A Input Low Voltage (All digital inputs) VIL 0 - 30% VBATT V Input High Voltage (all digital inputs) VIH 70% VBATT - VBATT V Input hysteresis (all digital inputs) Vhys 0.06 x VDD Internal pullup and pulldown resistors2 (all port pins and IRQ) RPU - 70 - Output High Voltage (IOH = -5 mA) (All digital outputs) VOH 80% VBATT - VBATT A -- V kohm V MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 37 Table 7. DC Electrical Characteristics (continued) (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, unless otherwise noted) Characteristic Output Low Voltage (IOL = 5 mA) (All digital outputs) Symbol Min Typ Max Unit VOL 0 - 20% VBATT V -- TBD mA TBD mA -- pF Maximum current in/out per IO pin Maximum total IOL for all IO pins IOLT -- Input capacitance (all non-supply pins) CIn -- 3 1 Maximum usable range of the reference voltage supply pin. This range may be modified because of the power supply configuration used in an application. See Table 6, "Power Supply Voltage". 2 Measurement condition for pull resistors: V = V IN SS for pullup and VIN = VDD for pulldown. 7.4 Supply Current Characteristics Table 8. Supply Current Characteristics (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, unless otherwise noted) Characteristics Symbol Typ Max Unit Off current Device is in reset condition (held in reset) and all GPIO at ground. 0.4 0.6 A Hibernate current RAM retained (8k, 32k, 64k, or 96k) 2KHz onboard oscillator or 32 kHz crystal oscillator CPU off (stop mode) wake-up from RTI timer, or external request Radio off ADCs not available 8 Kbyte RAM retention 32 Kbyte RAM retention 64 Kbyte RAM retention 96 Kbyte RAM retention 0.9 2.3 3.7 5.1 2.2 4.9 - A A A A Doze current RAM retained (8k, 32k, 64k, or 96k) Onboard 24 MHz oscillator on (high frequency accuracy) CPU off (stop mode) Radio off ADCs available, but inactive 8 Kbyte RAM retention 32 Kbyte RAM retention 64 Kbyte RAM retention 96 Kbyte RAM retention 55 57 58 60 70 - A A A A 0.85 .95 mA Idle current All RAM active Reference oscillator on (24 MHz) at 1.2 VDC CPU on at 1 MHz Reference clock available to all peripherals Radio off ADCs available, but inactive Min MC1322x Technical Data, Rev. 1.3 38 Freescale Semiconductor Table 8. Supply Current Characteristics (continued) (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, unless otherwise noted) Characteristics Typ Max Unit Run current All RAM active Reference oscillator on (24 MHz) at 1.2 VDC CPU on at reference frequency Radio off Reference clock available to all peripherals ADCs available, but inactive 3.3 7.3 mA Receive current All RAM active Reference oscillator on (24MHZ) at 1.2 VDC Radio RX on (receiving data) Reference clock available to all peripherals ADC_1 available, but inactive CPU on at 2 MHz (DCD) CPU on at 2 MHz (NCD) 22 24 25 - mA Transmit current All RAM active Reference oscillator on (24MHZ) at 1.2 VDC Radio TX on (sending data @ 0 dBm) Reference clock available to all peripherals ADCs available, but inactive CPU clock at 2 MHz 29 31 mA 7.5 Symbol Min RF AC Electrical Characteristics Table 9. Receiver AC Electrical Characteristics for 802.15.4 Modulation Mode (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, fref = 24 MHz, unless otherwise noted.) Characteristic Symbol Min Typ Max Unit - -96 -100 -91 - dBm - 10 - dBm - 38 38 57 57 65 35 35 50 50 60 dB Frequency Error Tolerance2 200 300 - kHz Symbol Rate Error Tolerance2 80 120 - ppm Sensitivity for 1% Packet Error Rate (PER)1 (+25 C, @ package interface; die sensitivity is ~1dB greater) Non-coherent Differential Chip Detection (DCD) Non-coherent Detection (NCD) Saturation (maximum input level) SENSmax Channel Rejection for 1% PER (desired signal -82 dBm) +5 MHz (adjacent channel) -5 MHz (adjacent channel) +10 MHz (alternate channel) -10 MHz (alternate channel) >= 15 MHz 1 The digital modem contains a block designated as the RX Modem. The Rx Modem can operate in: 1) Non-coherent Differential Chip Detection (DCD) mode which has 3-4dBm less sensitivity but requires 3-4mA less receiver current, and 2) Non-coherent Detection (NCD) mode which has 3-4dBm greater sensitivity but requires 3-4mA greater receiver current. 2 Minimum set by IEEE 802.15.4 Standard MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 39 Table 10. Transmitter AC Electrical Characteristics for 802.15.4 Modulation Mode (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, fref = 24 MHz, unless otherwise noted.) Characteristic Symbol Min Typ Max Unit Pout -2 1.5 4.5 dBm - +4 - dBm - 13 11 9 20 20 % Output Power Control Range - 35 - dB Over the Air Data Rate - 250 - kbps 2nd Harmonic3 - -55 - dBm/M Hz 3rd Harmonic3 - -64 - dBm/M Hz Nominal Output Power1 Maximum Output Power2 Error Vector Magnitude Pout @ -30 dBm Pout @ 0 dBm Pout @ +4 dBm EVM Spurious Emissions 30-1000 MHz 1-12.75GHz Nominal Impedance (RF_RX_TX) - dB dB 50 ohm 1 Register sets output power to nominal (0 dBm). Register sets output power to maximum. 3 Measurements taken at output of evaluation circuit set for maximum power out and averaged over 100ms. 2 Table 11. RF Port Impedance for Dual Port PA Output Pins Frequency Symbol PA_POS (Typ) PA_NEG (Typ) Unit 2.405 GHz 2.442 GHz 2.480 GHz Zout 64.7 - j43.9 64.5 - j42.9 64.3 - j42.0 61.0 - j31.9 60.7 - j30.7 60.4 - j29.5 MC1322x Technical Data, Rev. 1.3 40 Freescale Semiconductor 7.6 Crystal Reference Clock Oscillator Characteristics The reference oscillator model including external crystal in shown in Figure 10. The IEEE 802.15.4 Standard requires a frequency tolerance less than or equal to +/- 40 ppm as shown in the oscillator specification Table 12. With a suitable crystal (refer to Table 13 and Freescale Application Note AN3251), the device frequency tolerance can typically trimmed to be held to +/- 30 ppm over all conditions. REFERENCE OSCILLATOR MC13224V Course Tune[4] Course Tune[4] 4pF 4pF Course Tune[3:0] 8pF 4pF Course Tune[3:0] 1 MEG (nom) 2pF 1pF 8pF 4pF Fine Tune[4:0] 2pF 1pF Fine Tune[4:0] 0-5pF with steps of 160 fF. 0-5pF with steps of 160 fF. OSC_IN OSC_OUT Y1 CRYSTAL Cstray Cstray Figure 10. Reference Oscillator Model Table 12. Reference Oscillator Specifications Characteristic Symbol Frequency Oscillator frequency tolerance over temperature range. External load capacitance CLext Internal Osc startup time (13 MHz - 26 MHz)1 1 Min Typ Max Unit 13 24 26 MHz +/- 30 +/- 40 ppm None required (onboard) pF 0.8 ms 1.2 This is part of device wake-up time. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 41 Table 13. Recommended 24 MHz Crystal Specifications Parameter Value Unit 24.000000 MHz Frequency tolerance (cut tolerance)1 10 ppm at 25 C Frequency stability (temperature drift) 15 ppm Over desired temperature range Aging 2 ppm max Equivalent series resistance2 40-50 max Load capacitance 5-9 pF Shunt capacitance <2 pF Frequency Mode of oscillation 1 2 7.7 Condition max fundamental A wider frequency tolerance may acceptable if application uses trimming at production final test. The higher ESR may be acceptable with lower load capacitance. Optional 32.768 KHz Crystal Oscillator Specifications MC13224V 32.768 kHz OSCILLATOR Feedback OSC_IN OSC_OUT Y1 CRYSTAL Cstray1 CL1 CL2 Cstray2 Figure 11. 32.768 KHz Oscillator Mode l Table 14. 32.768 Oscillator Specifications Characteristic Symbol Min Crystal frequency1 Max 32.768 Frequency tolerance @ 25 C Frequency tolerance over Typ KHz 20 temperature2 -0.034 0.006ppm / Unit ppm (25-T)2 ppm MC1322x Technical Data, Rev. 1.3 42 Freescale Semiconductor Table 14. 32.768 Oscillator Specifications (continued) Characteristic Symbol Load capacitance Min Typ Max Unit 11 12.5 13 pF 60 k 1.35 pF 1 W Equivalent series resistance (ESR) Shunt capacitance Tolerated drive level 1 2 7.8 Recommended crystal Abracom Corporation crystal part number Example; Stability at -20xC is: -0.034 x (25-[-20])2= -68.8ppm. ABS25-32.768-12.5-B Internal Low Speed Reference Oscillator Specifications Table 15. Internal 2 KHz Oscillator Specifications Characteristic Symbol Min Typ Max Unit 2.5 1.7 3.5 KHz Oscillator frequency variation over full temperature range - +/- 13 - % Calibration time (in terms of 2KHz osc clocks) - - 216-1 osc clks Default Frequency @ 25 C 7.9 Control Timing and CPU Bus Specifications Table 16. MCU Control Timing (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, fref = 24 MHz, unless otherwise noted.) Parameter CPU Bus frequency (tcyc = 1/fBus) Symbol Min Typical Max Unit fBus fref/64 1 -- fref 1 MHz CPU Bus frequency with active TX or RX 2 Real-time interrupt internal oscillator frequency External reset pulse width2 External minimum interrupt pulse width (KBI[7:4]) 1 2 MHz 2 KHz - 4 -- osc clks - 4 -- osc clks Normal operation uses a 24 MHz reference. The MC1322x allows up to a 26 MHz max reference oscillator. This is the shortest pulse that is guaranteed to be recognized as a reset pin request. There always must be 3 clocks of the operating oscillator; this can vary from the low power oscillators to the reference oscillator. 7.9.1 Timer Module Input Characteristics Four-bit synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that can be used as the optional external source to the timer counter. These synchronizers operate from the peripheral clock rate. Table 17 shows timer input timing values. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 43 Table 17. Timer Input Timing (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, fref = 24 MHz, unless otherwise noted.) Parameter 7.10 Symbol Min Max Unit External clock frequency dc peripheral_bus_clk/3 MHz External clock period >3 -- tcyc Input capture pulse width >3 -- tcyc SPI Timing tCYC SPI_SCK tSS_H tSS_SU SPI_SS (slave in) tXX_SU tXX_H SPI_MOSI (slave in) SPI_MISO (master in) tMO,tSO SPI_MOSI (master out) SPI_MISO (slave out) Figure 12. SPI Timing Diagram Table 18 describes the timing requirements for the SPI system. Table 18. SPI Timing Parameter Symbol Min Master SPI_SCK Period tCYC peripheral_ Clk*2 Slave SPI_SCK Period tCYC tSS_SU tSS_H tSI_SU tSI_H tMI_SU tMI_H tMO tSO 10 ns 10 ns 10 ns 10 ns 10 ns 20 ns 0 ns Slave SPI_SS Setup Time Slave SPI_SS Hold Time Slave SPI_MOSI Setup Time Slave SPI_MOSI Hold Time Master SPI_MISO Setup Time Master SPI_MISO Hold Time Master SPI_MOSI Output Time Slave SPI_MISO Output Time (with 15 pf load) Typical 38 Max Unit peripheral_ Clk *256 ns 5 ns 20 ns MC1322x Technical Data, Rev. 1.3 44 Freescale Semiconductor 7.11 I2C Specifications Table 19 describes the timing requirements for the I2C system. The I2C module is driven by the peripheral bus clock (typically max 24 MHz) and the SCL bit clock is generated from a prescaler. The prescaler divide ratio can be programmed from 61,440 to 160 (decimal) which gives a maximum bit clock of 150 kbps. Table 19. I2C Signal DC Specifications (I2C_SDA and I2C_SCL) Parameter Symbol Min Typical Max Unit Input Low Voltage VIL -0.3 - 0.3 VDDINT V Input High Voltage VIH 0.7 VBATT - VBATT + 0.3 V Input hysteresis Vhys 0.06 x VBATT -- V Output Low Voltage1 (IOL = 5 mA) VOL 0 - 0.2 VBATT V Input Current (VIN = 0 V or VDDINT) IIN - - 1 A Pin capacitance Cin <10 pF 1 SDA and SCL are open drain outputs SDA tf tSU;DAT tr tLOW tHD:STA tBUF tr SCL tf tHD tSU;STA tHD;DAT tSU;STO tHIGH S Sr P S 2 Figure 13. I C Timing Diagram NOTE The C timing limits reflect values that are necessary meet to the I2C Bus specification. I2 MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 45 Table 20. I2C Signal AC Specifications1 Parameter Symbol Standard-Mode Fast-Mode Unit Min Max Min Max fSCL 0 100 0 150 kHz tHD;STA 4.0 - 0.6 - s LOW period of the SCL clock tLOW 4.7 - 1.3 - s HIGH period of the SCL clock tHIGH 4.0 - 0.6 - s tSU;STA 4.7 - 0.6 - s tSHD;DAT 02 3.453 02 0.93 s - ns SCL clock frequency (when source) Hold time (repeated) START condition. After this period, the first clock pulse is generated Set-up time for a repeated START condition Data hold time tSU:DAT 250 - 1004 Rise time for both SDA and SCL signals tr - 1000 20 + 0.1Cb5 300 ns Fall time for both SDA and SCL signals tf - 300 20 + 0.1Cb5 300 ns tBUF 4.7 - 1.3 - s Cb - 400 - 400 pF Data setup time Bus free time between a STOP and START condition Capacitive load for each bus line 1 All values referred to VIHmin and VILmax levels A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the undefined region of the falling edge of SCL. 3 The maximum t HD;DAT has only to be met if the device does not stretch the LOW period (tLOW) of the SCL signal. 4 A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement t SU;DAT >= 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line tr max + tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard-mode I2C-bus specification) before the SCL line is released. 5 C = total capacitance of one bus line in pF. If mixed with Hs-mode devices, the faster fall-times are allowed. b 2 MC1322x Technical Data, Rev. 1.3 46 Freescale Semiconductor 7.12 FLASH Specifications Table 21. FLASH Characteristics (TA = 25 C, fref = 24 MHz, unless otherwise noted.) Characteristic Symbol Min Supply voltage for program/erase/read (with directly regulated supply) Vprog/erase 1.70 SPI clock frequency Typical fFCLK Max Unit 1.90 V 13 MHz Read current (13 MHz) 9 15 mA Program and erase current 10 15 mA Standby current 2 10 A Sector erase duration 75 ms Block erase duration 75 ms Chip erase duration 150 ms Byte program duration 60 s Program/erase endurance 100,000 Data retention 7.13 tD_ret cycles 100 -- years ADC Characteristics Table 22. ADC Electrical Characteristics (Operating) (VBATT, LREG_BK_FB = 3.3 V, TA = 25 C, fref = 24 MHz, unless otherwise noted.) Characteristic ADC supply current (per ADC) Condition Symbol Min Typical Max Unit Enabled -- 2.9 6 mA Disabled -- 5 - A Reference potential, low VREFL VSS -- VREFH V Reference potential, high VREFH VREFL -- VBATT V Analog input voltage1 VINDC VSS - 0.2 -- VDD +0.2 V "Battery" input channel reference voltage 1 1.2 V Maximum electrical operating range, not valid conversion range. MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 47 Table 23. ADC Timing/Performance Characteristics Characteristic Symbol Condition Min Typ Max Unit Resolution - 12 Bits Effective Resolution 8 Bits Number of input channels ADC conversion clock frequency 8 - fADCCLK Conversion cycles (continuous convert) CCP Conversion time Tconv Analog Input 1 VAIN 300 6 Input Leakage Current Voltage1 - VDD KHz ADCCLK cycles 20 -- - s -- -- - nA VREFH V VREFL Analog input must be between VREFL + 0.2 and VREFH - 0.2 for valid conversion. 8 Developer Environment The MC1322x family is supported by a full set of hardware/software evaluation and development tools. 8.1 Hardware Development Interfaces The ARM debug environment supports both a JTAG debug interface and an extended capability Nexus interface. 8.1.1 JTAG Hardware Debug Port The JTAG port is the simpler and more common debug port for the ARM core. A standard 20-pin connector as described in Section 6.2.1, "ARM JTAG Interface Connector"", is connected to the TDI, TMS, TCK, TDO, and RTCK signals of the MC1322x. Through the JTAG serial interface, standard debug and development activities such as accessing memory and registers, control of the CPU, download of FLASH memory, and software debug can be accomplished. 8.1.2 A7S Nexus3 (NEX) ARM7 Core Development Interface The development and debug environment of the ARM7TDMI-S core is based on the A7S Nexus3 interface (compliant with a Class 3 device of the IEEE-ISTO 5001 standard for real-time embedded system design). This interface allows expansion of the development features of the JTAG port (through the addition of auxiliary signals, see Section 6.2.2, "Nexus Mictor Interface Connector"). Development features include: * Program Trace via Branch Trace Messaging (BTM). Branch trace messaging displays program flow discontinuities (direct and indirect branches, exceptions, etc.), allowing the development tool to interpolate what transpires between the discontinuities. Thus static code may be traced. MC1322x Technical Data, Rev. 1.3 48 Freescale Semiconductor * * * * * * * * * 8.2 Data Trace via Data Write Messaging (DWM) and Data Read Messaging (DRM). This provides the capability for the development tool to trace reads and/or writes to (selected) internal memory resources. Ownership Trace via Ownership Trace Messaging (OTM). OTM facilitates ownership trace by providing visibility of which process ID or operating system task is activated. An Ownership Trace Message is transmitted when a new process/task is activated, allowing the development tool to trace ownership flow. Run-time access to the memory map via the JTAG port. This allows for enhanced download/upload capabilities Watchpoint Messaging (WPM) via the auxiliary pins Watchpoint Trigger enable of Program and/or Data Trace Messaging Auxiliary interface for higher data input/output Registers for Program Trace, Ownership Trace, Watchpoint Trigger, and Read/Write Access Programmable processor stall function to mitigate message queue overrun risk All features controllable and configurable via the JTAG port Software Development Tools An Integrated Development Environment (IDE) is available to facilitate the development of embedded applications targeting the MC1322x platform. Features of the IDE include: * Project management tools and code editor * Highly optimizing ARM compiler supporting C and C++ * Extensive JTAG and RDI debugger support * Run-time libraries including source code * Relocating ARM assembler * Linker and librarian tools * Debugger with ARM simulator, JTAG support and support for RTOS-aware debugging on hardware * RTOS plug-ins available * Code templates for commonly used code constructs * Sample projects for evaluation boards * User and reference guides, both printed and in PDF format * Context-sensitive online help The IDE is complemented by the BeeKitTM Wireless Connectivity Toolkit. BeeKit is a stand alone software application targeting Windows(R) operating systems. BeeKit provides a graphical user interface (GUI) in which users can create, modify, save, and update wireless networking solutions. With the solution explorer property list windows, users can set configuration parameters to control the setup and execution behavior of the wireless link within their application. The configuration parameters can be validated inside BeeKit to ensure all values provided are within acceptable ranges prior to generation of a workspace. All this functionality provides a mechanism for developers to configure and validate their network parameters MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 49 without having to navigate through multiple source files to configure the same parameters. BeeKit supports Freescale's Simple MAC (SMAC), IEEE 802.15.4-compliant MAC, and the Freescale BeeStackTM. 8.3 Development Hardware Several different development modules and kits will be available to allow evaluation of ZigBee and IEEE 802.15.4 applications. The modules will provide capabilities for Coordinator, Router, and End Device nodes. Reference designs will be available for RF design and low power applications including 2-layer and 4-layer PCBs. MC1322x Technical Data, Rev. 1.3 50 Freescale Semiconductor 9 Mechanical Diagrams (Case 1901-01, non-JEDEC) Figure 14. Mechanical Diagram (1 of 2) MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 51 Figure 15. Mechanical Diagram Bottom View (2 of 2) MC1322x Technical Data, Rev. 1.3 52 Freescale Semiconductor NOTES MC1322x Technical Data, Rev. 1.3 Freescale Semiconductor 53 How to Reach Us: Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064, Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-521-6274 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com Document Number: MC1322x Rev. 1.3 10/2010 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. Freescale and the Freescale logo are trademarks or registered trademarks of Freescale Semiconductor, Inc. in the U.S. and other countries. All other product or service names are the property of their respective owners. ARM is the registered trademark of ARM Limited. ARM7TDMI-S is the trademark of ARM Limited.(c) Freescale Semiconductor, Inc. 2006, 2007, 2008, 2009, 2010