Produktbegleitbrief DEUTSCH Stromversorgung SITOP power Dual 15V MLFB 6EP1353-0AA00 ! Gefahr WARNHINWEISE Die Stromversorgung ist eine geregelte Stromversorgung, ausgelegt als Einbaugerat fur den Einsatz am einphasigen Wechselstromnetz. Fur die Installation des Gerates sind die einschlagigen DIN/VDEBestimmungen oder die landerspezifischen Vorschriften zu beachten. Der Anschlu der Versorgungsspannung mu gema VDE 0100 und VDE 0160 ausgefuhrt werden. Eine Schutzeinrichtung (Sicherung) und Trenneinrichtung zum Freischalten der Stromversorgung mu vorgesehen werden. Der einwandfreie und sichere Betrieb dieses Gerates setzt sachgemaen Transport, fachgerechte Lagerung, Montage und Installation voraus. ! Gefahr Gefahr durch elektrischen Schlag! Beim Betrieb elektrischer Gerate stehen zwangslaufig bestimmte Teile dieser Gerate unter gefahrlicher Spannung. Unsachgemaer Umgang mit diesen Geraten kann deshalb zum Tod oder schweren Korperverletzungen sowie zu erheblichen Sachschaden fuhren. ACHTUNG! Elektrostatisch gefahrdete Bauelemente (EGB). Nur geschultes Personal darf das Gerat offnen! TECHNISCHE DATEN Eingang Eingangsnennspannung UE: AC 120/230 V AC 93 V bis 264 V Eingangsspannungsbereich: Frequenzbereich: 47 Hz bis 63 Hz 1,9A/ 1,15A Eingangsnennstrom IE: Wirkungsgrad : eingebaute Sicherung: empfohlener LS-Schalter: 80% T 4A/ 250V 10A/ Charakteristik C 16A/ Charakteristik B Ausgang Ausgange potentialfrei, kurzschlu- und leerlauffest. 105W Gesamtleistung: P15_1 Ausgangsnennspannung: Einstellbereich: Toleranz statisch: Ausgangsstrom: P15_2 Ausgangsnennspannung: INSTALLATION Die Stromversorgung darf nur von einem qualifizierten Fachmann montiert und verdrahtet werden, der die allgemein gultigen Regeln der Technik und die jeweils gultigen Vorschriften und Normen kennt und beachtet. Einstellbereichbereich: Toleranz statisch: Ausgangsstrom: Der Anschlu einer flexibler Netzzuleitung mu mit Aderendhulsen erfolgen. Die Baugruppe ist als geschlossene Bauform fur die Hutschiene DIN EN 50022-35x15 und 50022-35x7,5 ausgefuhrt. Zum Aufschnappen das Gerat mit den Nasen in die Hutschiene einhangen und andrucken, dabei die Feder mit einem Schraubendreher nach unten drucken, bis das Gerat einschnappt. Zur Demontage von der Hutschiene mit Schraubendreher die Feder nach unten losen und Gerat abnehmen. Vorsicht! Das Gerat ist zwecks ordnungsgemaer Entwarmung so zu montieren, da die vertikale Stromungsrichtung nicht behindert wird. Die Steckverbinder befinden sich dabei unten. Unterhalb und oberhalb des Gerates soll mindestens ein Freiraum von je 10 cm eingehalten werden, um die Konvektion nicht zu behindern. Bei Parallelschaltung sind die beiden Ausgange moglichst genau auf gleiche Ausgangsspannung einzustellen und uber gleichlange Leitungen mit der Last zu verbinden. NORMEN / ZULASSUNGEN Elektrische Schutz- und Sicherheitsanforderungen primar/ sekundar SELV nach EN 50178, EN 60950 DC 15V +102...108% bei Auslieferung DC 14,5V - 17V 2% DC 0 ... 3,5A bei 45C (max. 52,5W) 0 ... 2,5A bei 60C (max. 37,5W) DC 15V +102...108% bei Auslieferung DC 14,5V - 17V 2% DC 0 ... 3,5A bei 45C (max. 52,5W) 0 ... 2,5A bei 60C (max. 37,5W) 1% Summenstorspannung: Kurzschluschutz: Einsatzpunkt Kurzschlustrom 110%...140% INenn 140%...180% INenn Anzeige Ausgangsspannung: LED grun bei UA > 10V Umgebungsbedingungen zulassige Umgebungstemperatur: - im Betrieb: - bei Transport/Lagerung 0 C bis + 45C 0 C bis + 60C mit Derating - 40C bis + 70C relative Luftfeuchtigkeit: 5 - 95%, ohne Betauung Schutzart (VDE 0470-1) Schutzklasse (VDE 0106-1) IP 20 I Gewicht 0,750 kg Abmessungen: (BxHxT) 75x125x125 Elektromagnetische Vertraglichkeit Storaussendung: EN 50081-2;Klasse A Storfestigkeit: EN 50082-2;Klasse A Surge nach EN 50082-1 Zulassungen UL SIEMENS A&D SE E6 UL508, Listed, File E179336 J32025-K0047-M001-A2-7429 02.04.01 Anschlubelegung Anschluplan fur einen Ausgang +-15V/3,5A Anschluplan fur zwei Ausgange 15V/3,5A P15_1 P15_1 P15_2 P15_2 P15_1 GND1 P15_2 P15_2 GND2 L1 N PE DC OK +15V 0V P15_1 Ausgang 15V/ 3,5A GND1 Ausgang +-15V/ 3,5A P15_2 +15V 0V +15V Ausgang 15V/ 3,5A P15_2 0V -15V GND2 L1 Netzeingang 120V/ 230V N PE Netzeingang 120V/ 230V DC OK Hinweis: Diese Betriebsanleitung enthalt aus Grunden der Ubersichtlichkeit nicht samtliche Detailinformationen zu allen Typen des Produkts und kann auch nicht jeden denkbaren Fall der Aufstellung, des Betriebes oder der Instandhaltung berucksichtigen. Technische Anderungen jederzeit vorbehalten. In Zweifelsfallen gilt der deutsche Text. SIEMENS A&D SE E6 J32025-K0047-M001-A2-7429 02.04.01 Product-accompanying document (ENGLISH) power supply unit SITOP power Dual 15V MLFB 6EP1353-0AA00 ! Danger Technical specifications Warning notes SITOP power Dual is a stabilized power supply unit designed for use on the single-phase a.c. mains. The power supply unit must be installed in compliance with the relevant DIN/VDE regulations or the specific national standards. The connection to the supply voltage must be performed in accordance with VDE 0100 and VDE 0160. A protective device (fuse) and a disconnecting switch for safety isolation of the power supply unit must be provided. The faultless and safe operation of the unit depends on a proper transport and storage, as well as installation by qualified personnel. ! Danger Risk of electric shock! During the operation of any electric devices, it is necessary that certain parts of these devices are subject to hazardous voltages. Improper use of these devices can therefore result in loss of life or severe personal injuries, as well as substantial property damage. Potentiometer UA is only allowed to be actuated. Input Rated Input voltage UE: Input voltage range: Frequency range: Rated input current IE: AC 120/230 V AC 93 V to 264 V 47 Hz bis 63 Hz 1,9A/ 1,15A Efficiency : Internal fuse: Recommended circuitbreaker: 80% T 4A/ 250V 10A/ Charakteristik C 16A/ Charakteristik B Output isolated output, Short circuit- and open circuit proof 105W Total power: P15_1 Rated output voltage: Adjusting range: Static tolerance: Output current: Caution ! Electrostatic sensitive devices (ESD). Devices may only be opened by qualified personnel ! P15_2 Rated output voltage: INSTALLATION SITOP power Dual may only be installed and wired by a qualified expert, who observes the generally applicable technical standards and the relevant standards and specifications. Adjusting range: Static Tolerance: Output current: Connect flexible wires only with wire end ferrules. SITOP power Dual is designed as a built-in device for mounting on DIN EN 50022-35x15 or DIN EN 50022-35x7,5 bars. To snap the unit on to the DIN bar, hang it with its nose into the bar, use a screw driver to loosen the spring, until the spring snaps into place. To remove from the DIN bar, use a screw driver to loosen the spring in the direction of the arrow. Caution! To ensure proper heat dissipation, install the unit at the horizontal bar according to DIN EN 50022 with the terminals arranged in the lower area of the unit. Clearances of 10 cm should be provided above and beneath the unit, in order not to restrict the convection. Parallel connection of two devices to increase the power is permitted, if the output voltages are adjusted equally and the length of the leads to the load is equal). DC 15V +102...108% as delivered DC 14,5V 17V 2% DC 0 ... 3,5A at 45C (max. 52,5W) 0 ... 2,5A at 60C (max. 37,5W) DC 15V +102...108% as dilivered DC 14,5V - 17V 2% DC 0 ... 3,5A to 45C (max. 52,5W) 0 ... 2,5A to 60C (max. 37,5W) Ripple/ noise: Short circuit protection: Current limiting threshold Short circuit current 1% Indication of output voltage: LED green at UA > 10V Environmental conditions Ambient temperature: - during operation: 110%...140% IE 140%...180% IE - during transport/storage 0 C bis + 45C 0 C bis + 60C with derating - 40C bis + 70C Relative air humidity 5 - 95%, without condensation Degree of protection to (VDE 0470-1) Protection class to (VDE 0106-1) IP 20 Weight 0,750 kg Dimension: 75x125x125 Certificates Electrical Protection and Safety primary/secondary SELV to EN 50178, EN 60950 Elektromagnetic compatibility EN 50081-2;class A Emitted interference: EN 50082-2;class A Interference immunity: Surge to EN 50082-1 Certificates UL SIEMENS A&D SE E6 I UL 508, Listed, File E179336 J32025-K0047-M001-A2-7429 02.04.01 Terminal connection Connection of one output voltage +-15V/3,5A Connection of two output voltages 15V/3,5A P15_1 P15_1 P15_2 P15_2 P15_1 GND1 P15_2 P15_2 +15V 0V P15_1 Output 15V/ 3,5A 0V Output 15V/ 3,5A GND2 P15_2 Output +-15V/ 3,5A 0V -15V GND2 L1 N GND1 P15_2 +15V +15V L1 Input 120V/ 230V N PE PE DC OK DC OK Input 120V/ 230V Note: These instructions cannot claim to cover all details of possible equipment variations nor in particular can they provide for every possible example of installation, operation or maintenance. Subject to change without prior notice. In case of doubt, the German text shall be applicable SIEMENS A&D SE E6 J32025-K0047-M001-A2-7429 02.04.01