CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP Surface Mount PXJ - Series Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. Rated voltage range : 2.5 to 25Vdc, Capacitance range : 56 to 1,200F Case size range :6.3x5.8L to 8x6.7L Suitable for DC-DC converters, voltage regulators and decoupling applications used on computer motherboards etc. Solvent resistant type (see PRECAUTIONS AND GUIDELINES) RoHS2 Compliant Halogen Free PXJ Downsizing PXG SPECIFICATIONS Items Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current *Note Dissipation Factor (tan) Low Temperature Characteristics (Max. Impedance Ratio) Endurance Bias Humidity Surge Voltage Soldering Heat Failure Rate Characteristics -55 to +105 2.5 to 25Vdc 20% (M) Rated voltagex1.15 Shall not exceed values shown in STANDARD RATINGS. (at 20, 120Hz) (at 105) (at 20 after 2 minutes) 0.12 max. (at 20, 120Hz) Z(-25)/Z(+20)1.15 Z(-55)/Z(+20)1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 15,000 hours at 105. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) 150% of the initial specified value ESR 150% of the initial specified value Leakage current The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20 after subjecting them to the DC rated voltage at 60, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) 150% of the initial specified value ESR 150% of the initial specified value Leakage current The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105 for 30 seconds through a protective resistor(R=1k) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change 20% of the initial value D.F. (tan) 150% of the initial specified value ESR 150% of the initial specified value Leakage current The initial specified value The following specifications shall be satisfied when the solder temperature is reduced back to 20C to measure dip resistance after soldering has been performed under the recommended soldering conditions. Appearance No significant damage Capacitance value Within the specified tolerance range D.F. (tan) The initial specified value ESR The initial specified value Leakage current The initial specified value (Voltage treatment) 0.5% per 1,000 hours maximum (Confidence level 60% at 105) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105. DIMENSIONS [mm] Terminal MARKING Code : A EX) 2.5V820F 0.3max. L0.3 P A0.2 C0.2 B0.2 D0.5 W Size Code D F61 6.3 F80 6.3 FA0 6.3 H70 8 L 5.8 7.7 9.7 6.7 A 6.6 6.6 6.6 8.3 B 6.6 6.6 6.6 8.3 C 7.2 7.2 7.2 9.0 W 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.7 to 1.1 P 1.9 1.9 1.9 3.1 J57A 820 2.5V Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001T CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP Surface Mount PXJSeries - PART NUMBERING SYSTEM 1 2 3 4 A PXJ 5 6 7 8 9 10 A RA 11 12 13 14 M 15 16 17 18 Supplement code (Note 1) Size code Capacitance tolerance code Capacitance code (ex. 22F:220, 39F:390) Taping code Terminal code Voltage code (ex. 20V:220, 25V:250) Series code Category Please refer to "Product code guide (conductive polymer type)" Note1:PXJ series, 16V270F (Rated ripple current 5,080mArms) have supplement code"J". Terminal and terminal plating are the same as all other in PXJ series. STANDARD RATINGS WV (Vdc) 2.5 6.3 10 16 20 25 Cap (F) Size code Leakage current (A max./after 2min.) 820 820 820 1,000 1,200 1,200 390 560 560 680 270 390 390 470 220 270 270 270 390 150 150 150 220 56 82 82 120 F61 F80 FA0 FA0 FA0 H70 F61 F80 FA0 H70 F61 F80 FA0 H70 F61 F80 F80 FA0 H70 F61 F80 FA0 H70 F61 F80 FA0 H70 1,020 1,020 1,020 1,250 1,500 1,500 1,220 1,760 1,760 2,140 1,350 1,950 1,950 2,350 704 864 864 864 1,240 600 600 600 880 280 410 410 600 ESR Rated ripple current (m max./20, 100k to 300kHz) (mArms/105, 100kHz) 10 7 10 10 10 10 10 8 10 10 15 13 13 15 20 10 13 16 25 23 18 18 28 28 28 28 38 4,900 5,000 4,300 4,300 4,300 4,500 4,900 5,000 4,300 4,500 4,000 4,460 4,000 4,000 3,500 5,080 4,460 3,500 3,600 3,300 3,790 3,200 3,300 3,000 3,040 3,000 3,200 Part No. APXJ2R5ARA821MF61G APXJ2R5ARA821MF80G APXJ2R5ARA821MFA0G APXJ2R5ARA102MFA0G APXJ2R5ARA122MFA0G APXJ2R5ARA122MH70G APXJ6R3ARA391MF61G APXJ6R3ARA561MF80G APXJ6R3ARA561MFA0G APXJ6R3ARA681MH70G APXJ100ARA271MF61G APXJ100ARA391MF80G APXJ100ARA391MFA0G APXJ100ARA471MH70G APXJ160ARA221MF61G APXJ160ARA271MF80J APXJ160ARA271MF80G APXJ160ARA271MFA0G APXJ160ARA391MH70G APXJ200ARA151MF61G APXJ200ARA151MF80G APXJ200ARA151MFA0G APXJ200ARA221MH70G APXJ250ARA560MF61G APXJ250ARA820MF80G APXJ250ARA820MFA0G APXJ250ARA121MH70G RATED RIPPLE CURRENT MULTIPLIERS Frequency Multipliers FrequencyHz SMD type 120 0.05 1k 0.30 10k 0.55 50k 0.70 100k to 500k 1.00 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001T