ES2A tHRu ES2J 2.0 AMP. SUPER FAST RECOVERY SILICON RECTIFIERS VOLTAGE RANGE 50 to 600 Volts FEATURES * For surface mounted application x Extremely low thermal resistance * Easy pick and place * High temp soldering: 250C for 10 seconds at terminals * Superfast recovery times for high efficiency MECHANICAL DATA * Case; Molded plastic * Terminals: Solder plated * Polarity: Indicated by cathod band * Packaging: 12mm tape per EIA STD RS-481 * Weight:0.093 grams SMB/DO-214AA .075(1.90) 139(3.52) 082(2.08) 141(3.58)_ .184(4.875) |.~ "186(4.725) _. 006(.18) 012(.30} 0842.13) \ 086(2. 43) ( | .035(0.88) 000%0.00 044(T. 12) TONG Dy .204(5.18 ~220(5.59) Dimensions in inches and( millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Maxmum thermal resistance: 15C/W Junction to lead. Rating at 25C ambient temperature unless otherwise specified. TYPE NUMBER SYMBOLS| ES2A | S2B | ES2C | S2D ; ES2G ES2J | UNITS Maximum Recurrent Peak Reverse Voltage VrRM 50 100 150 200 400 600 Vv Maximum RMS Voltage Vams 35 70 105 140 280 420 Vv Maximum DC Blocking Voltage Vpe 50 100 50 200 400 600 v Maximum Average Forward Rectified Current Ty = 75C Irvav) 2.0 A Peak Forward Surge Current, (8.3 ms half sine) lesm 50 A Maximum Instantaneous lem =2.0A Forward Voltage(Note 1) = Ty =25C Ve 0.98 1.35 17 V Maximum D.C Reverse Current @ Ta = 25T \ 10 A at Rated D.C. Blocking Voltage @ Ta =100T R 350 Maximum Reverse Recovery Time( Note 2) Tr 35 nS Typical Junction Capacitance (Note 3) Cy 25 20 pF Operating and Storage Temperature Range Ty/ Tste -50to +150 / -50to +150 c NOTES: 1. Pulse test: Pulse width 300 psec, Duty cycle 1% 2.Reverse Recovery Test Conditions: ip =0.5A. Iq = 1.0A, In; =0.25A 3.Measured at 1 MHz and applied reverse voltage of 4.0V D.C. JINAN GUDE ELECTRONIC DEVICE CO., LTD.3 INSTANTANEOUS FORWARD CURRENT. (A) 2 RATINGS AND CHARACTERISTIC CURVES (ES2A THRU ES2J) Figure 2 - Forward Current Derating Curve Figure 1 Typical - Forward Characteristics 24 WIDTH-3004S 2.2 1% DUTY . P.C.B mounted on 2.0 0.2 x 0.2"(5.0 5.0mm) 1.8 copper pad area Ss of> P 1.6 e atA <1.2 1,0 Single Phase,Hall Wave 60Hz Resistive or inductive Load eth @ & 25 50 76 100 125 150 0.6 0.8 1.0 1.2 14 16 18 a - FORWARD VOLTAGE. (V) Coed tere CurreniAmperes versus Figure 3 - Typical Junction Capacitance 60 rT Tj=25C c f=1.0MHz 2 50 Vsig=50mVp-p TY _ wi z g A ~ 40 3 NUL Bas 5 30 A 324 Zz we] 2 Corel Qo 20 & aa z S26. oc 7 : Pe 10 1 Pang ~ by 0 0 1 10 100 REVERSE VOLTAGE. (V) JINAN GUDE ELECTRONIC DEVICE Co., LTD.PEAK FORWARD SURGE CURRENT. (A) RATINGS AND CHARACTERISTIC CURVES (ES2A THRU ES2J) Figure 4 - Maximum Non - repetitive Surge Current 2 3S 8.3ms Singte Half Sine Wave Method) at TL=120C 1 10 100 NUMBER OF CYCLES AT 60H2 Figure 6 Reverse Recovery Time Characteristic And Test Circuit Diagram Figure 5 - SUGGESTED SOLDER PAD LAYOUT = 25Voc OSCILLOSCOPE (NOTE 1) NOTES: 1 Rise Time=7 ns max. Input Impedance= | 1 megohm 22pF PULSE GENERATOR (NOTE 2) 2 Rise Time={0Ons max. Source Impedance= 50 ohms 3 Resistors are non-inductive 0.078" 3 0.070" [* }Trr ->| +0.5A -0.25A -1.0A SET TIME BASE FOR 50/200nsicm JINAN GUDE ELECTRONIC DEVICE CO., LTD.