SSD P4 Solid State Drive Product Manual Rev 1.1 SSD P4 Solid State Drive Product Manual Rev 1.1 October 2010 The content of this document is subject to change without notice Document No. 80-11-XXXX1 SanDisk Corporation Corporate Headquarters * 601 McCarthy Blvd. * Milpitas, CA 95035 Phone (408) 801-1000 * Fax (408) 801-8657 www.sandisk.com (c) 2010 SanDisk(R) Corporation 1 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 SanDisk Corporation general policy does not recommend the use of its products in life support or other applications where in a failure or malfunction of the product may directly threaten life or injury. Per SanDisk Terms and Conditions of Sale, the user of SanDisk products in life support or other such applications assumes all risk of such use and agrees to indemnify, defend and hold harmless SanDisk Corporation and its affiliates against all damages. See "Disclaimer of Liability." This document and related material is for information use only and is subject to change without prior notice. SanDisk Corporation assumes no responsibility for any errors that may appear in this document or related material, nor for any damages or claims resulting from the furnishing, performance or use of this document or related material. SanDisk Corporation explicitly disclaims any express and implied warranties and indemnities of any kind that may or could be associated with this document and related material, and any user of this document or related material agrees to such disclaimer as a precondition to receipt and usage hereof. No part of this document may be reproduced, transmitted, transcribed, stored in a retrievable manner or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written consent of an officer of SanDisk Corporation. All parts of the SanDisk documentation are protected by copyright law and all rights are reserved. SanDisk and the SanDisk logo are registered trademarks of SanDisk Corporation, registered in the U.S. and other countries. All other brand names mentioned herein are for identification purposes only and may be trademarks and/or registered trademarks of their respective holder(s). (c) 2008 - 2010 SanDisk Corporation. All rights reserved. Document No. 80-11-XXXX1 05/10 (c) 2010 SanDisk(R) Corporation Printed in U.S.A. 2 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Revision History Revision 0.1 0.2 Description * Initial draft May 20, 2010 * * * * * * Major document format changes Updated LDE values Update performance values Updated power consumption values Added SanDisk SSD P4 block diagram Added Standard SATA with large screw hole size form factor mechanical specification & ordering information Updated Ordering information (decoder keys) July 15, 2010 * * Added 4GB capacity data Updated Reliability & MTTF numbers August 9, 2010 * Added details of 2.5"/7mm cased SSD P4 form-factor August 27, 2010 * Update MTTF numbers for 4GB and 128GB capacities. Update Identify Data table: o Word 69 - Changed Trim support from Deterministic to non-Deterministic. o Word 83 - Set correct bit to indicate SET MAX Security Extension Supported. o Word 105 - Indicate support for 1 sector of LBA Range Entries (Trim). September 27, 2010 Updated 4GB power consumption numbers. Removed "Preliminary" document status. October 6, 2010 Update Identify Data table: o Word 77 now reports the SATA Phy speed per the SATA 3.0 specification. Added support of "Enhanced Mode" Security Erase Unit command (words 90 and 128). October 28, 2010 * 0.3 0.4 * 0.5 * 1.0 Date * * 1.1 * (c) 2010 SanDisk(R) Corporation 3 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Table of Contents 1. INTRODUCTION............................................................................................................................... 8 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 2. GENERAL PRODUCT SPECIFICATIONS ............................................................................................ 13 2.1 2.2 2.3 2.4 3. INTERFACE ............................................................................................................................... 13 CAPACITY ................................................................................................................................ 13 PERFORMANCE ......................................................................................................................... 14 ENDURANCE ............................................................................................................................ 14 POWER CHARACTERISTICS ............................................................................................................ 15 3.1 3.2 3.3 3.4 4. GENERAL DESCRIPTION ................................................................................................................. 8 KEY FEATURES ............................................................................................................................ 9 FUNCTIONAL DESCRIPTION .......................................................................................................... 10 DEFECT AND ERROR MANAGEMENT............................................................................................... 10 WEAR LEVELING ....................................................................................................................... 10 BAD BLOCK MANAGEMENT ......................................................................................................... 10 NON-VOLATILE WRITE CACHE ...................................................................................................... 11 POWER MANAGEMENT .............................................................................................................. 11 SUPPLY VOLTAGE ...................................................................................................................... 15 AVERAGE POWER CONSUMPTION ................................................................................................. 15 ACTIVE POWER CONSUMPTION .................................................................................................... 15 LOW POWER MODE CONSUMPTION .............................................................................................. 16 PHYSICAL SPECIFICATION .............................................................................................................. 17 HALF 1.8" - STANDARD SATA CONNECTOR .................................................................................... 17 4.1 4.1.1 Standard SATA 4GB-64GB capacity................................................................................... 17 4.1.2 Standard SATA 128GB capacity ........................................................................................ 19 4.1.3 Standard SATA with large screw hole size ......................................................................... 21 4.2 HALF 1.8" - MICRO-SATA CONNECTOR ........................................................................................ 23 4.2.1 Micro-SATA 8GB-64GB capacity ....................................................................................... 23 4.2.2 Micro-SATA 128GB capacity ............................................................................................. 25 4.3 MSATA FORM FACTOR .............................................................................................................. 27 4.3.1 mSATA 8GB-64GB capacity............................................................................................... 27 4.3.2 mSATA 128GB capacity .................................................................................................... 29 4.4 MSATA MINI FORM FACTOR ....................................................................................................... 31 4.4.1 mSATA Mini 8GB-32GB capacity....................................................................................... 31 4.4.2 mSATA Mini 64GB capacity .............................................................................................. 33 4.5 7MM CASED FORM FACTOR ........................................................................................................ 35 4.5.1 2.5" 7mm Cased Form Factor 4GB-64GB........................................................................... 35 5. ENVIRONMENTAL SPECIFICATIONS ............................................................................................... 36 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 6. TEMPERATURE ......................................................................................................................... 36 HUMIDITY ............................................................................................................................... 36 VIBRATION .............................................................................................................................. 36 SHOCK.................................................................................................................................... 36 ALTITUDE ................................................................................................................................ 36 ELECTROSTATIC DISCHARGE (ESD) ................................................................................................ 37 ACOUSTICS .............................................................................................................................. 37 EMI/RFI COMPLIANCE .............................................................................................................. 37 ROHS .................................................................................................................................... 37 REGULATIONS .......................................................................................................................... 38 RELIABILITY CHARACTERISTICS...................................................................................................... 39 (c) 2010 SanDisk(R) Corporation 4 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 6.1 6.2 7. Product Manual Rev 1.1 ERROR RATE ............................................................................................................................ 39 MTTF (MEAN-TIME-TO-FAILURE) ................................................................................................ 39 INTERFACE .................................................................................................................................... 40 7.1 7.2 7.3 7.4 8. SUPPORTED STANDARDS ............................................................................................................. 40 PIN ASSIGNMENTS - STANDARD SATA........................................................................................... 40 PIN ASSIGNMENTS - MICRO-SATA ............................................................................................... 41 PIN ASSIGNMENTS - MSATA ....................................................................................................... 42 SUPPORTED ATA COMMANDS ...................................................................................................... 43 8.1 8.2 9. 10. IDENTIFY DATA ......................................................................................................................... 46 LOG PAGES .............................................................................................................................. 50 ORDERING INFORMATION ............................................................................................................ 51 CONTACT INFORMATION ......................................................................................................... 52 (c) 2010 SanDisk(R) Corporation 5 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Table of Figures FIGURE 1-1: SANDISK SSD P4 BLOCK DIAGRAM .................................................................................................. 8 FIGURE 1-2: SANDISK SSD P4 NCACHETM TECHNOLOGY ....................................................................................... 11 FIGURE 4-1: STANDARD SATA 4GB-64GB TOP AND SIDE VIEW WITH KEEP OUT AREA................................................. 17 FIGURE 4-2: STANDARD SATA 4GB-64GB TOP/BOTTOM VIEW WITH MORE DETAILS ................................................. 18 FIGURE 4-3: STANDARD SATA 128GB TOP/BOTTOM VIEW WITH KEEP OUT AREA ...................................................... 19 FIGURE 4-4: STANDARD SATA 128GB TOP VIEW WITH MORE DETAILS AND SIDE VIEW ................................................ 20 FIGURE 4-5: STANDARD SATA WITH LARGE SCREW HOLE SIZE TOP VIEW WITH MORE DETAILS ........................................ 21 FIGURE 4-6: STANDARD SATA WITH LARGE SCREW HOLE SIZE BOTTOM VIEW & SIDE VIEW ........................................... 22 FIGURE 4-7: MICRO-SATA 8GB-64GB TOP/BOTTOM VIEW ................................................................................ 23 FIGURE 4-8: MICRO-SATA 8GB-64GB TOP AND SIDE VIEWS WITH MORE DETAILS .................................................... 24 FIGURE 4-9: MICRO-SATA 128GB TOP/BOTTOM VIEW ..................................................................................... 25 FIGURE 4-10: MICRO-SATA 128GB TOP VIEW AND SIDE VIEW WITH MORE DETAILS ................................................. 26 FIGURE 4-11: MSATA 8GB-64GB TOP AND SIDE VIEW ...................................................................................... 27 FIGURE 4-12: MSATA 8GB-64GB BOTTOM VIEW ............................................................................................. 28 FIGURE 4-13: MSATA 128GB TOP AND SIDE VIEWS ........................................................................................... 29 FIGURE 4-14: MSATA 128GB BOTTOM VIEW ................................................................................................... 30 FIGURE 4-15: MSATA MINI 8GB-32GB TOP AND SIDE VIEWS ............................................................................. 31 FIGURE 4-16: MSATA MINI 8GB-32GB BOTTOM VIEW ..................................................................................... 32 FIGURE 4-17: MSATA MINI 64GB TOP AND SIDE VIEWS ..................................................................................... 33 FIGURE 4-18: MSATA MINI 64GB BOTTOM VIEW ............................................................................................ 34 FIGURE 4-19: 2.5" 7MM CASED FORM FACTOR ................................................................................................. 35 (c) 2010 SanDisk(R) Corporation 6 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Table of Tables TABLE 2-1: SANDISK SSD P4 CAPACITY SPECIFICATION ........................................................................................ 13 TABLE 2-2: SANDISK SSD P4 PERFORMANCE .................................................................................................... 14 TABLE 2-3: SANDISK SSD P4 ENDURANCE ....................................................................................................... 14 TABLE 3-1: SANDISK SSD P4 SUPPLY VOLTAGE ................................................................................................. 15 TABLE 3-2: SANDISK SSD P4 AVERAGE POWER CONSUMPTION ............................................................................. 15 TABLE 3-3: SANDISK SSD P4 ACTIVE POWER CONSUMPTION ................................................................................ 15 TABLE 3-4: SANDISK SSD P4 POWER CONSUMPTION IN LOW POWER MODE ............................................................ 16 TABLE 4-1: MECHANICAL INFORMATION - STANDARD SATA FORM FACTOR............................................................... 17 TABLE 4-2: MECHANICAL INFORMATION - STANDARD SATA WITH LARGE SCREW HOLE SIZE........................................... 21 TABLE 4-3: MECHANICAL INFORMATION - MICRO-SATA FORM FACTOR ................................................................... 23 TABLE 4-4: MECHANICAL INFORMATION - MSATA FORM FACTOR ........................................................................... 27 TABLE 4-5: MECHANICAL INFORMATION - MSATA MINI FORM FACTOR ................................................................... 31 TABLE 4-6: MECHANICAL INFORMATION - 7MM CASED FORM FACTOR .................................................................... 35 TABLE 5-1: SANDISK SSD P4 TEMPERATURE SPECIFICATION ................................................................................. 36 TABLE 5-2: SANDISK SSD P4 HUMIDITY SPECIFICATION ....................................................................................... 36 TABLE 5-3: SANDISK SSD P4 VIBRATION SPECIFICATION ...................................................................................... 36 TABLE 5-4: SANDISK SSD P4 SHOCK SPECIFICATION............................................................................................ 36 TABLE 5-5: SANDISK SSD P4 ALTITUDE SPECIFICATION ........................................................................................ 36 TABLE 5-6: SANDISK SSD P4 ESD SPECIFICATION .............................................................................................. 37 TABLE 5-7: SANDISK SSD P4 EMI/RFI COMPLIANCE .......................................................................................... 37 TABLE 5-8: SANDISK SSD P4 REGULATION STANDARDS ....................................................................................... 38 TABLE 6-1: SANDISK SSD P4 MTTF ............................................................................................................... 39 TABLE 7-1: STANDARD SATA CONNECTOR PIN ASSIGNMENT ................................................................................ 40 TABLE 7-2: MICRO-SATA CONNECTOR PIN ASSIGNMENT ..................................................................................... 41 TABLE 7-3: MSATA CONNECTOR PIN ASSIGNMENT ............................................................................................. 42 TABLE 8-1: SUPPORTED ATA COMMANDS ........................................................................................................ 45 TABLE 8-2: IDENTIFY DATA VALUES ................................................................................................................. 49 TABLE 8-3: SUPPORTED SMART LOG PAGES ..................................................................................................... 50 TABLE 9-1: ORDERING INFORMATION .............................................................................................................. 51 TABLE 9-2: EXAMPLES OF DECODED SKU .......................................................................................................... 51 (c) 2010 SanDisk(R) Corporation 7 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 1. Introduction 1.1 General Description The SanDisk(R) SSD P4 builds on the momentum of the first and second generations of pSSD and the overall trend in the market towards smaller, thinner computing machines that enable mobility and connectivity on the go. Using NAND flash based storage to replace Hard Disk Drives, SSD P4 provides a much improved user experience. In addition to being rugged and reliable, the third generation modular SSD beats HDDs in every possible metric - power consumption, sequential and random read performances as well as sequential and random write performances. The SATA interface aligns with the global transition in the industry, which is enforced by the platform's chipsets. Using the advanced 32nm memory geometry provides for a low cost product which beats the HDDs price in the capacity ranges of 4GB-32GB and provides a very competitive product at capacities of 64GB and 128GB. In addition, the small form factor enables further miniaturization of Netbooks, SmartBooks and Tablets designs and opens doors for a whole range of other applications. The SSD P4 product electrically complies with the SATA-II ver. 2.6 standards and is electrically compatible with a serial ATA disk drive. In addition to the mass storage-specific NAND flash memory chips, the SSD includes an on-board intelligent controller for managing interface protocols, data storage and retrieval, error-correcting code (ECC), defect handling and diagnostics, advance power management and clock control. Using innovative data management algorithms, the SSD P4 provides superior sequential and random IO performance, and ensures data reliability. 16-bit wide NAND Flash SSD Controller SATA Gen-II Interface NAND Flash Array - 0 High-Speed NAND Flash I/F 16-bit wide NAND Flash Array - 1 SanDisk SSD P4 Figure 1-1: SanDisk SSD P4 Block Diagram Unlike an HDD, the SSD P4 has no moving parts. It keeps working in environments such as classrooms, kiosks and in space-restricted server racks. The patented flash management technology brings top data integrity to the SSD, even during power losses. Dynamic bad block management, dynamic and static wear-leveling, and robust error detection and correction code (EDC/ECC) ensure data integrity. Once the SSD has been configured by the host, it appears to the host as a standard ATA (IDE) disk drive. (c) 2010 SanDisk(R) Corporation 8 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 1.2 Product Manual Rev 1.1 Key Features High capacity, ultra-small form factor supporting unformatted capacities1 of 4GB, 8GB, 16GB, 32GB, 64GB and 128GB: o Half 1.8" with a 2.5" Standard SATA connector, complies to the Jedec297 standard o Half 1.8" with a micro SATA connector o Standard mSATA form factor with a Mini-PCIe connector, complies to the Jedec MO-300A standard o mSATA Mini form factor with a Mini-PCIe connector Interface to host o SATA II revision 2.6, 3.0Gbps High performance 2 o Host transfer rate: 300 MB/s o Sustained Read: 160 MB/s o Sustained Write: 100 MB/s o 4K Random Write (Sustained): 135 IOPS o 4K Random Write (Recovered): 690 IOPS o 4K Random Read: Low power consumption o 2200 IOPS Typical read/write 3: 0.18W o Slumber mode: Highly reliable 60mW o Mean time to failure (MTTF): 4,530,805 hours, based on Part Stress Analysis o Operating shock: 1,500G, 0.5msec half sine o Operating vibration: 5gRMS, 10-2000 Hz o Operating temperature: 0C to 70C o Non-operating temperature and storage: -55C to +85C 1 The logical capacity of the drive conforms to the IDEMA HDD Specification. See www.idema.org for details. Some of the listed capacity is used for formatting and other functions, and thus is not available for data storage. 1 megabyte (MB) = 1 million bytes; 1 gigabyte (GB) = 1 billion bytes. 2 These performance numbers refer to the 32GB product. Based on internal testing; performance may vary 3 Average (typical) power while running MobileMarkTM 2007 with Device Initiated Power Management (DIPM) enabled. (c) 2010 SanDisk(R) Corporation 9 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 1.3 Product Manual Rev 1.1 Functional Description SSD P4 contains a high level, intelligent subsystem. This intelligent (microprocessor) subsystem provides many capabilities not found in other types of memory cards. These capabilities include the following: * Standard ATA register and command set * Support for Trim command * S.M.A.R.T. feature supported * Host independence from details of erasing and programming flash memory * Sophisticated system for managing defects (similar to systems found in magnetic disk drives) * Sophisticated system for error recovery including a powerful error correction code (ECC) * Advanced power management for low power operation * Implementation of dynamic and static wear-leveling to extend card's life 1.4 Defect and Error Management SSD P4 contains a sophisticated defect and error management system that is similar to the systems found in magnetic disk drives, and in many cases, offers enhancements. If necessary, the SSD card will rewrite data from a defective sector to a good sector. This action is completely transparent to the host and does not consume any user data space. The SSD soft error rate specification is much better than the magnetic disk drive specification. In the extremely rare case that a read error does occur, the SSD P4 products have innovative algorithms to recover the data by using error detection code and error correction code (EDC/ECC). These defect and error management systems, coupled with the solid state construction, give SSD P4 unparalleled reliability. 1.5 Wear Leveling Wear leveling is an intrinsic part of the erase pooling functionality of SSDs using NAND memory. Advanced features of dynamic and static wear-leveling, and automatic block management are used to ensure an even distribution of write erase cycle throughout the entire device, regardless of how dynamic or static the data written is. This guarantees high data reliability and maximizes flash life expectancy. 1.6 Bad Block Management Bad blocks are occasionally created during the life cycle of a flash component, in a phenomenon called dynamic bad-block accumulation. These bad blocks must be marked and replaced dynamically in order to prevent read/write failures. When a bad block is detected, the embedded Bad Block Mapping algorithm maps out the block, which will be not used for storage anymore. (c) 2010 SanDisk(R) Corporation 10 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 1.7 Product Manual Rev 1.1 Non-Volatile Write Cache The third generation of modular SSD, the SSD P4 supports a unique feature to improve random write performance and ensure very positive user experience. Studies show that modern operating systems mostly access the storage device using small access blocks, with the majority being a 4KB access blocks. The small logical access blocks conflict with the physical block structure (>1MB) for the newer generation flash memory technology. Therefore, to bridge this difference, SSD P4 employs a non-volatile SLC Flash write cache, nCacheTM. The nCacheTM is used to accumulate these small writes (called segments) at high speed and then flush & consolidate them to larger MLC section of the NAND Flash memory array in the background during idle time. nCacheTM SLC Flash MLC NAND Flash Controller SATA-II I/F nCacheTM SLC Flash MLC NAND Flash Figure 1-2: SanDisk SSD P4 nCacheTM technology The cache size of the SSD P4 is over 500MB 4 - an order of magnitude larger than other competing solutions that use DRAM based cache. Due to its large size, for most part of daily user activity nCacheTM never overflows and the end users experience high SLC burst performance rather than the sustained performance. Once the nCacheTM becomes full, the performance of SSD P4 drops to the steady state condition. Also nCacheTM is a non-volatile cache and hence there is no exposure to data loss 5. 1.8 Power Management SSD P4 supports an advanced power management system that includes both Host Initiated Power Management (HIPM) and Device Initiated Power Management (DIPM). Upon completion of a command, the SSD will ask the host to enter into Slumber Mode to conserve power if no further commands are received within 20msec. By directly entering Slumber mode and skipping partial mode will minimize power consumption. In order to further enhance the SSD performance, the flash management can utilize the time when the card is idle for performing internal housekeeping operations. Doing those activities, i.e. - freeing up space in the nCache, while the card is idle will not increase overall power consumption, since these operations will have to be executed eventually. Executing them during idle time will prevent stalling the host while they are taking place and will enable a better utilization of the Data Cache, as it will have additional free space when the host will 4 The cache size scales with capacity. For 32GB product the cache size is over 500MB. 5 In order to prevent any data loss during removal of the power supply (with Host Write Cache disabled), the time it takes the input voltage to drop from the nominal voltage down to 2V must be at least 5ms. (c) 2010 SanDisk(R) Corporation 11 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 access the device. These operations are executed internally, while the card is indicating status ready to the host. At the moment a new command is received from the host the internal operations will be terminated and the host command will be serviced with minimal delay. If no command is received the execution of the housekeeping activities will be limited to 30 seconds, to preserve power consumption. (c) 2010 SanDisk(R) Corporation 12 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 2. General Product Specifications 2.1 Interface The SSD P4 interface complies with the Serial ATA standard published by ANSI. The device complies with the SATA II, ver. 2.6 specifications and supports ATA-8 ACS. For more information, refer to the American National Standard X3.221: AT Attachment for Interface for Disk Drives document. Documentation can be ordered from IHS by calling 1-800-854-7179 or accessing their Web site: http://global.ihs.com 2.2 Capacity Unformatted Capacity 6 Total Number of UserAddressable Sectors in LBA Mode 7 Number of Logical Cylinders Number of Logical Heads Number of Logical Sectors per Track 4GB 7,835,183 7,772 16 63 8GB 15,649,200 15,525 16 63 16GB 31,277,232 16,383 16 63 32GB 62,533,296 16,383 16 63 64GB 125,045,424 16,383 16 63 128GB 250,069,680 16,383 16 63 Table 2-1: SanDisk SSD P4 Capacity Specification 6 1 gigabyte (GB) = 1 billion bytes. Some of the listed capacity is used for formatting and other functions, and thus is not available for data storage. 7 1 Sector = 512 bytes. (c) 2010 SanDisk(R) Corporation 13 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Performance 2.3 Parameter Unit 4GB 8GB 16GB 32GB 64GB 128GB 300 300 300 Host transfer rate SATA II, MB/s 300 300 300 3.0Gbps Transfer rates Sequential MB/s 60 130 140 160 160 160 MB/s 12 25 50 100 100 100 IOPs 2600 2400 2300 2200 2200 2200 IOPs 50 100 135 135 135 120 IOPs 600 680 680 690 690 690 250 typical; 500 max 250 typical; 500 max 250 typical; 500 max Read 8 Sequential Write Random Read [4KB] 9 Random Write - Sustained [4KB] Random Write - Recovered [4KB] Typical power- msec. 250 250 250 typical; typical; typical; 500 max 500 max 500 max on ready time Table 2-2: SanDisk SSD P4 Performance 2.4 Endurance Parameter Long Term Data Endurance (LDE) 10 4GB 8GB 16GB 32GB 64GB 128GB 2.5TBW 5TBW 10TBW 20TBW 40TBW 80TBW Table 2-3: SanDisk SSD P4 Endurance 8 Using HDBench on Windows7TM OS based PC as a secondary drive with host write cache enabled. File size of 100MB. 9 Using IOMETER 2006.07.27 with host write cache enabled. The measurement is of 4KB aligned random accesses across 100% of the drive's capacity. 10 LDE is calculated based on typical workload based on Windows OS. LDE is a direct function of user workload and access pattern. LDE is defined in terms of Terabytes Written, "TBW." (c) 2010 SanDisk(R) Corporation 14 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 3. Power Characteristics 3.1 Supply Voltage Parameter Specifications Form Factor Input Voltage Standard SATA connector 5V 5% Micro SATA connector 3.3V 5% mSATA / mSATA Mini 3.3V 5% Maximum Ripple 70mV (peak to peak), 0 - 30MHz Supply Rise Time 7 msec to 100 msec Table 3-1: SanDisk SSD P4 Supply Voltage 3.2 Average Power Consumption 11 Input Voltage 5V 5% Parameter Read/Write [mW] 3.3V 5% Read/Write [mW] 4GB 8GB 16GB 32GB 64GB 128GB 170 180 180 200 200 200 140 140 140 175 175 175 Table 3-2: SanDisk SSD P4 Average Power Consumption 3.3 Active Power Consumption 12 Input Voltage 5V 5% 3.3V 5% Parameter 4GB 8GB 16GB 32GB 64GB 128GB Read [mW] 475 500 550 700 725 725 Write [mW] 500 600 900 1425 1450 1450 Read [mW] 375 450 500 650 650 650 Write [mW] 400 500 850 1200 1400 1400 Table 3-3: SanDisk SSD P4 Active Power Consumption 11 Average (typical) power while running MobileMarkTM 2007 with Device Initiated Power Management (DIPM) enabled. 12 Active power consumption is measured during long sequential (either read or write) operations. (c) 2010 SanDisk(R) Corporation 15 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 3.4 Input Voltage 5V 5% 3.3V 5% Product Manual Rev 1.1 Low Power Mode Consumption Parameter Partial / Slumber Mode [mW] Partial / Slumber Mode [mW] 4GB 8GB 16GB 32GB 64GB 128GB 60 60 60 60 60 60 57 57 57 57 57 57 Table 3-4: SanDisk SSD P4 Power Consumption in Low Power Mode (c) 2010 SanDisk(R) Corporation 16 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 4. Physical Specification 4.1 Half 1.8" - Standard SATA Connector Complies with SFF-8156/ MO-297 standards Parameter Specifications Width 54mm Length 39mm Thickness (max) 3.08mm (4-64GB), 4.38mm (128GB) Connector 4.00mm Typical Weight 6.4g (8-32GB), 7.4g (64GB), 8.7g (128GB) Table 4-1: Mechanical Information - Standard SATA form factor 4.1.1 Standard SATA 4GB-64GB capacity Figure 4-1: Standard SATA 4GB-64GB Top and Side view with keep out area (c) 2010 SanDisk(R) Corporation 17 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-2: Standard SATA 4GB-64GB Top/Bottom View with more details (c) 2010 SanDisk(R) Corporation 18 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.1.2 Product Manual Rev 1.1 Standard SATA 128GB capacity Figure 4-3: Standard SATA 128GB Top/Bottom view with keep out area (c) 2010 SanDisk(R) Corporation 19 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-4: Standard SATA 128GB Top view with more details and Side view (c) 2010 SanDisk(R) Corporation 20 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.1.3 Product Manual Rev 1.1 Standard SATA with large screw hole size Parameter Specifications Width 54mm Length 38.75mm Thickness (max) 3.08mm Connector 4.00mm Typical Weight 6.4g (8-32GB) Table 4-2: Mechanical Information - Standard SATA with large screw hole size Figure 4-5: Standard SATA with large screw hole size Top View with more details (c) 2010 SanDisk(R) Corporation 21 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-6: Standard SATA with large screw hole size Bottom View & Side view (c) 2010 SanDisk(R) Corporation 22 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.2 Product Manual Rev 1.1 Half 1.8" - Micro-SATA Connector Parameter Specifications Width 54mm Length 39mm Thickness (max) 3.08mm (8-64GB), 4.38mm (128GB) Connector 4.00mm Typical Weight 5.9g (8-32GB), 6.9g (64GB), 8.1g (128GB) Table 4-3: Mechanical Information - Micro-SATA form factor 4.2.1 Micro-SATA 8GB-64GB capacity Figure 4-7: Micro-SATA 8GB-64GB Top/Bottom View (c) 2010 SanDisk(R) Corporation 23 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-8: Micro-SATA 8GB-64GB Top and Side Views with more details (c) 2010 SanDisk(R) Corporation 24 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.2.2 Product Manual Rev 1.1 Micro-SATA 128GB capacity Figure 4-9: Micro-SATA 128GB Top/Bottom View (c) 2010 SanDisk(R) Corporation 25 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-10: Micro-SATA 128GB Top View and Side View with more details (c) 2010 SanDisk(R) Corporation 26 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.3 Product Manual Rev 1.1 mSATA Form Factor Complies with MO-300 Standard Parameter Specifications Width 30mm Length 50.95mm Thickness (max) Typical Weight 3.4mm (8-64GB), 3.7mm (128GB) 5g (8-32GB), 6g (64GB), 7.2g (128GB) Table 4-4: Mechanical Information - mSATA form factor 4.3.1 mSATA 8GB-64GB capacity Figure 4-11: mSATA 8GB-64GB Top and Side View (c) 2010 SanDisk(R) Corporation 27 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-12: mSATA 8GB-64GB Bottom View (c) 2010 SanDisk(R) Corporation 28 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.3.2 Product Manual Rev 1.1 mSATA 128GB capacity Figure 4-13: mSATA 128GB Top and Side views (c) 2010 SanDisk(R) Corporation 29 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-14: mSATA 128GB Bottom view (c) 2010 SanDisk(R) Corporation 30 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.4 Product Manual Rev 1.1 mSATA Mini Form Factor Complies with MO-300 Standard Parameter Specifications Width 30mm Length 26.80mm Thickness (max) 3.4mm (8-32GB), 3.7mm (64GB) Typical Weight 3.4g (8-32GB), 4.0g (64GB) Table 4-5: Mechanical Information - mSATA Mini form factor 4.4.1 mSATA Mini 8GB-32GB capacity Figure 4-15: mSATA Mini 8GB-32GB Top and Side Views (c) 2010 SanDisk(R) Corporation 31 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-16: mSATA Mini 8GB-32GB Bottom View (c) 2010 SanDisk(R) Corporation 32 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.4.2 Product Manual Rev 1.1 mSATA Mini 64GB capacity Figure 4-17: mSATA Mini 64GB Top and Side Views (c) 2010 SanDisk(R) Corporation 33 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Figure 4-18: mSATA Mini 64GB Bottom View (c) 2010 SanDisk(R) Corporation 34 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 4.5 Product Manual Rev 1.1 7mm Cased Form Factor Complies to SFF-xxxx Parameter Specifications Width 100.49mm Length 69.85mm Thickness (max) 7mm Typical Weight TBD Table 4-6: Mechanical Information - 7mm Cased form factor 4.5.1 2.5" 7mm Cased Form Factor 4GB-64GB Figure 4-19: 2.5" 7mm cased Form Factor (c) 2010 SanDisk(R) Corporation 35 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 5. Environmental Specifications 5.1 Temperature Parameter Specifications Operational 0C to 70C Storage -55C to 85C Maximum temperature gradient 1C per minute Table 5-1: SanDisk SSD P4 Temperature Specification 5.2 Humidity Parameter Specifications Operational Humidity (Non condensation) 5% to 95% Maximum wet bulb 35C Non-operational Humidity (Non condensation) 5% to 95% Maximum wet bulb 40C Maximum relative humidity gradient 20% per hour Table 5-2: SanDisk SSD P4 Humidity Specification 5.3 Vibration Parameter Specifications Operational / Non-operational 5gRMS, 10-2000 Hz, 3 axes Table 5-3: SanDisk SSD P4 Vibration Specification 5.4 Shock Parameter Acceleration Force Half Sine pulse duration Operational / 1000G 1ms Non operational 1500G 0.5ms Table 5-4: SanDisk SSD P4 Shock Specification 5.5 Altitude Parameter Specifications Non-Operational -1500ft (-457m) to 40,000ft (12,192m) Operational -1500ft (-457m) to 10,000ft (3048m) Table 5-5: SanDisk SSD P4 Altitude Specification (c) 2010 SanDisk(R) Corporation 36 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Electrostatic Discharge (ESD) 5.6 The SanDisk SSD P4's are ESD tested per IEC 61000-4-2 Standard. Parameter Test Voltage Contact 2kV, 4kV Air 4kV, 8kV Table 5-6: SanDisk SSD P4 ESD Specification 5.7 Acoustics The SSD P4 does not generate any acoustics noise (0dB). 5.8 EMI/RFI Compliance The SanDisk SSD P4 is certified to comply with the following standards. Standard FCC Part 15 Class B IECS-003 Class B EN 55022 Class B EN 55024 KCC No. 2008-39 KCC No. 2008-38 CNS 13438 VCCI: 2006 AS/NZS CISPR 22: 2006 Table 5-7: SanDisk SSD P4 EMI/RFI Compliance 5.9 RoHS European union's restriction on use of hazardous substances in electrical and electronic equipment (EU RoHS) Directive 2002/95/EC. China's management methods for controlling pollution by electronic information products (China RoHS). (c) 2010 SanDisk(R) Corporation 37 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 5.10 Regulations The SanDisk SSD P4 is certified with the following certifications: Standard CE UL (with file number) CSA (or ULc) CE WEEE TUV/SEMKO/UL/etc. MIC (Korea) (with certification number) BSMI (Taiwan) (with applicant code number) VCCI (Japan) C-Tick (Australia) FCC China RoHS HF (Halogen Free) EuP Table 5-8: SanDisk SSD P4 Regulation Standards (c) 2010 SanDisk(R) Corporation 38 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 6. Reliability Characteristics 6.1 Error Rate Non-recoverable error rate is 1 error per 1014 bits read. 6.2 MTTF (Mean-Time-To-Failure) The reliability figure of merit most often used for electronic equipment is Mean-TimeTo-Failure (MTTF). SanDisk estimates MTTF using a prediction methodology based in accordance with the Telcordia Special Report SR-332. The prediction is based on a Parts Stress Analysis. Quality levels were defined as industrial grade (I) for all of the components. The detailed prediction for the system was performed at a temperature of 25C in a GB environment. The following table summarizes the estimated MTTF results for each capacity. Capacity Condition MTTF (Hours) Estimated FITs 4GB Telcordia SR-332, GB, 25C 5,100,000 196 8GB Telcordia SR-332, GB, 25C 4,958,071 202 16GB Telcordia SR-332, GB, 25C 4,806,968 208 32GB Telcordia SR-332, GB, 25C 4,530,805 215 64GB Telcordia SR-332, GB, 25C 4,063,862 221 128GB Telcordia SR-332, GB, 25C 2,912,038 343 Table 6-1: SanDisk SSD P4 MTTF (c) 2010 SanDisk(R) Corporation 39 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 7. Interface 7.1 Supported Standards The SSD P4 complies with the following standards: SATA II, ver. 2.6 ATA-8 command set 7.2 Pin Assignments - Standard SATA SIGNAL Connector Pinout: Pin # Signal Name Description S1 GND 2nd mate S2 A+ RxP S3 A- RxM S4 GND 2nd mate S5 B- TxM S6 B+ TxP S7 GND 2nd mate POWER Connector Pinout: Pin # Signal Name Description P1 V33 Not connected P2 V33 Not connected P3 V33 Not connected P4 GND 1st mate P5 GND 2nd mate P6 GND 2nd mate P7 V5 5V power input, pre-charge, 2nd mate P8 V5 5V power input P9 V5 5V power input P10 GND 2nd mate P11 DAS/RSS Device Activity Signal P12 GND 1st mate P13 V12 Not connected P14 V12 Not connected P15 V12 Not connected Table 7-1: Standard SATA Connector Pin Assignment (c) 2010 SanDisk(R) Corporation 40 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 7.3 Product Manual Rev 1.1 Pin Assignments - Micro-SATA SIGNAL Connector Pinout: Pin # Signal Name Description S1 GND 2nd mate S2 A+ RxP S3 A- RxM S4 GND 2nd mate S5 B- TxM S6 B+ TxP S7 GND 2nd mate POWER Connector Pinout: Pin # Signal Name Description P1 V33 3.3V power P2 V33 3.3V power - pre charge P3 GND GND P4 GND GND P5 V5 Not Connected P6 V5 Not Connected P7 DAS Device Activity Signal P8 GND GND P9 Optional Not Connected Table 7-2: Micro-SATA Connector Pin Assignment (c) 2010 SanDisk(R) Corporation 41 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 7.4 Pin # Product Manual Rev 1.1 Pin Assignments - mSATA Assignment Description Pin # Assignment Description 1 No Connect 2 +3.3V 3.3V Source 3 No Connect 4 GND Return Current Path 5 No Connect 6 No Connect 7 No Connect 8 No Connect Return Current Path 10 No Connect 11 No Connect 12 No Connect 13 No Connect 14 No Connect Return Current Path 16 No Connect 17 No Connect 18 19 No Connect 20 No Connect Return Current Path 22 No Connect 9 15 21 GND GND GND 23 +B - TXP 25 -B - TXN 27 GND 29 GND Transmitter Differential Signal Pair Transmitter Differential Signal Pair GND Return Current Path 24 +3.3V 3.3V Source 26 GND Return Current Path Return Current Path 28 No Connect Return Current Path 30 No Connect 32 No Connect Receiver Differential Signal Pair Receiver Differential Signal Pair 31 -A - RXN 33 +A - RXP 35 GND Return Current Path 36 No Connect 37 GND Return Current Path 38 No Connect 39 +3.3V 3.3V Source 40 41 +3.3V 3.3V Source 42 No Connect 43 No Connect 44 No Connect 45 No Connect 46 No Connect 47 No Connect 48 No Connect 50 52 49 DA/DSS Device Activity 51 Presence Detection Pulled low by the device 34 GND Return Current Path GND Return Current Path GND Return Current Path +3.3V 3.3V Source Table 7-3: mSATA Connector Pin Assignment (c) 2010 SanDisk(R) Corporation 42 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 8. Supported ATA Commands The following table defines some of the common ATA commands supported by the SSD P4. Specifics of each ATA command's operation can be found in the AT Attachment 8 - ATA/ATAPI Command Set (ATA-8 ACS) document. Command Name ATA8 Code Check Power Mode M E5h Data Set Management O 06h Trim 01h Device Configuration Overlay DCO subcommands: O B1h Restore C0h Freeze Lock C1h Identify C2h Set C3h Identify DMA C4h Set DMA C5h Download Microcode O 92h Download (without offsets) and save microcode. 07h Execute Device Diagnostic M 90h Flush Cache M E7h Flush Cache Ext O EAh Identify Device M ECh Idle M E3h Idle Immediate M E1h Initialize Drive Parameters Obs 91h NOP O 00h Read Buffer O E4h Read DMA M C8h Read DMA Ext O 25h Read DMA w/o Retry Obs C9h Read Log Ext O 2Fh Read Multiple M C4h Read Multiple Ext O 29h Read Native Max Address O F8h Read Native Max Addr Ext O 27h Read Sectors M 20h Read Sectors Ext O 24h Read Sectors w/o Retry Obs 21h Read Verify Sectors M 40h Read Verify Sectors Ext O 42h Read Verify Sectors w/o Retry Obs 41h (c) 2010 SanDisk(R) Corporation 43 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Recalibrate Obs 1Xh Security Disable Password O F6h Security Erase Prepare O F3h Security Erase Unit O F4h Security Freeze Lock O F5h Security Set Password O F1h Security Unlock O F2h Seek Obs 7Xh Set Features M EFh Set Features subcommands: Enable write cache 02h Set transfer mode 03h Enable SATA features 10h Device-Initiated Interface Power Management 03h Software Setting Preservation 06h Disable read look-ahead 55h Disable reverting to power-on defaults 66h Disable write cache 82h Disable SATA features 90h Device-Initiated Interface Power Management 03h Software Setting Preservation 06h Enable read look-ahead AAh Enable reverting to power-on defaults CCh Set Max Address Security Extension subcommands: O F9h Set Max Set Password 01h Set Max Lock 02h Set Max Unlock 03h Set Max Freeze Lock 04h Set Max Set Password DMA 05h Set Max Unlock DMA 06h Set Max Address Ext O 37h Set Multiple Mode M C6h Sleep M E6h Smart O B0h Smart subcommands: Read Attribute Values (Read Data) D0h Read Attribute Thresholds Obs D1h Enable/Disable Attribute Autosave O D2h Save Attribute Values D3h Execute LBA Offline Low Immediate: (c) 2010 SanDisk(R) Corporation Execute off-line immediate routine 44 D4h 00h Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Execute Short Self-test routine (Offline) 01h Execute Extended Self-test routine (Offline) 02h Abort off-line immediate routine 7Fh Execute Short Self-test routine (Captive) 81h Execute Extended Self-test routine (Captive) 82h Read Log D5h Write Log D6h Enable Operations D8h Disable Operations D9h Read Status DAh Disable Auto Offline Obs DBh Standby M E2h Standby Immediate M E0h Write Buffer O E8h Write DMA M CAh Write DMA Ext O 35h Write DMA FUA Ext M 3Dh Write DMA w/o Retry Obs CBh Write Log Ext O 3Fh Write Multiple M C5h Write Multiple FUA Ext M CEh Write Multiple Ext O 39h Write Sectors M 30h Write Sectors Ext O 34h Write Sectors w/o Retry Obs 31h Write Uncorrectable Ext O 45h Pseudo-UECC with Logging 55h M = Mandatory. O = Optional. Obs = Obsolete Table 8-1: Supported ATA Commands (c) 2010 SanDisk(R) Corporation 45 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 8.1 Product Manual Rev 1.1 Identify Data The following table defines the specifics of the Identify Data returned by the SSD P4. Word Address Default Value Total Bytes Data Field Type Information 0 0040h 2 ATA General configuration: bit-significant information 1 3FFFh 2 ATA Default number of cylinders (depends on capacity) 2 C837h 2 Reserved 3 0010h 2 Default number of heads 4-5 0000h 4 Obsolete 6 003Fh 2 Default number of sectors per track 7-9 0000h 6 Obsolete 10-19 ASCII 20 Serial number in ASCII (left-justified) 20-22 0000h 6 Obsolete 23-26 SSD 8.XX 8 Firmware revision in ASCII (left-justified) 27-46 SanDisk SSD P4 XXGB 40 Model number in ASCII (left-justified) 47 8001h 2 Maximum No. of sectors in Read/Write Multiple command 48 0000h 2 Reserved 49 2F00h 2 LBA and MWDMA modes supported 50 4000h 2 Capabilities 51 0200h 2 PIO data transfer cycle timing mode 52 0000h 2 Obsolete 53 0007h 2 Field validity 54 3FFFh 2 Current number of cylinders (depends on capacity) 55 0010h 2 Current number of heads 56 003Fh 2 Current sectors per track 57-58 XXXXh 4 Current capacity in sectors (LBAs) 59 0101h 2 Multiple sector setting is valid (Multiple = 1) 60-61 XXXXh 4 Total number of sectors addressable in LBA Mode 62 0000h 2 Obsolete 63 0007h 2 64 0003h 2 Advanced PIO modes supported 65 0078h 2 Minimum multiword DMA transfer cycle time per word (ns) 66 0078h 2 Recommended multiword DMA transfer cycle time per word in ns (c) 2010 SanDisk(R) Corporation Bits:15-8: Multiword DMA mode active Bits: 0-7: Multiword DMA modes supported 46 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Word Address Default Value Product Manual Rev 1.1 Total Bytes Data Field Type Information 67 0078h 2 Minimum PIO transfer without flow control 68 0078h 2 Minimum PIO transfer with IORDY flow control 69 1200h 2 ATA8-ACS2 Additional Supported 70-74 0000h 10 Reserved 75 0000h 2 Queue Depth 76 0206h 2 SATA capabilities 77 000Xh 2 SATA Additional capabilities (0002=1.5Gbps, 0004=3.0Gbps) 78 0048h 2 SATA Features Supported 79 0040h 2 SATA Features Enabled 80 01F0h 2 Major Version number 81 0107h 2 Minor Version number 82 746Bh 2 Command set supported 83 7D01h 2 Command sets supported 84 4163h 2 Command set/feature supported extension 85 7469h 2 Command set/feature enabled 86 BC01h 2 Command set/feature enabled 87 4163h 2 Command set/feature default 88 007Fh 2 Ultra DMA Mode supported and selected 89 0001h 2 Time required for security erase-unit completion (all capacities complete < 2 minutes) 90 0001h 2 Time required for Enhanced security erase completion (all capacities complete < 2 minutes) 91 0000h 2 Current advanced power management value 92 FFFEh 2 Master Password Identifier 93 0000h 2 Hardware Reset Result 94 0000h 2 Current AAM Value 95 0000h 2 Stream Min Request Size 96 0000h 2 Streaming Transfer Time-DMA 97 0000h 2 Streaming Access Latency 98-99 0000h 4 Streaming Performance Granularity 100-103 XXXXh 8 48-bit # of LBA's 104 0000h 2 Streaming Transfer Time-PIO 105 0001h 2 Max # 512-byte Blocks in LBA Range Entries 106 4000h 2 Physical Sector Size/Logical (c) 2010 SanDisk(R) Corporation 47 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Word Address Default Value Product Manual Rev 1.1 Total Bytes Data Field Type Information 107 0000h 2 Inter-Seek Delay for ISO7779 108-111 5001B440XXXX XXXXh 8 WWN 112-115 0000h 8 Reserved 116 0000h 2 Reserved for TLC 117-118 0000h 4 Logical Sector Size 119 4004h 2 Command/Feature Sets Supported #4 120 4004h 2 Command/Feature Sets Enabled 121-126 0000h 12 Reserved 127 0000h 2 Obsolete 128 0021h 2 Security Status 129-159 0000h 62 Reserved vendor-unique bytes 160-167 0000h 16 Reserved 168 0004h 2 Device Nominal Form Factor 169 0001h 2 ATA8-ACS2 Data Set Management Support 170-175 0000h 12 Reserved 176-205 0000h 60 Current Media Serial Number (not supported) 206 0000h 2 SCT Command Transport 207-208 0000h 4 Reserved for CE-ATA 209 4000h 2 Alignment-Logical within Physical Block 210-211 0000h 4 Wr/Rd/Vfy Sector Count Mode 3 212-213 0000h 4 Wr/Rd/Vfy Sector Count Mode 2 214 0000h 2 NV Cache Capabilities 215-216 0000h 4 NV Cache Size in Logical Blocks 217 0001h 2 Nominal Media Rotation Rate 218 0000h 2 Reserved 219 0000h 2 NV Cache Options 220 0000h 2 Wr/Rd/Vfy Feature Set-Current Mode 221 0000h 2 Reserved 222 1011h 2 Transport Major Version Number 223 0000h 2 Transport Minor Version Number 224-233 0000h 20 Reserved for CE-ATA 234 0000h 2 Min Sector Count for DL Microcode Mode 3 235 0000h 2 Max Sector Count for DL Microcode Mode 3 (c) 2010 SanDisk(R) Corporation 48 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Word Address Default Value Product Manual Rev 1.1 Total Bytes Data Field Type Information 236-254 0000h 38 Reserved for CE-ATA 255 XXXXh 2 Integrity Word-Checksum Table 8-2: Identify Data Values (c) 2010 SanDisk(R) Corporation 49 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 Log Pages 8.2 The following table defines the list of supported Log Pages accessible through SMART Write Log, SMART Read Log, Read Log Ext and Write Log Ext commands. Log Address Total Pages Log Address Description 0 1 General Purpose Log Directory 3 `n' Ext Comprehensive SMART Error Log 6 1 SMART Self-Test Log 80h-9Fh 16 Host Vendor-specific Logs Table 8-3: Supported SMART Log Pages (c) 2010 SanDisk(R) Corporation 50 Document No. 80-11-XXXX1 SSD P4 Solid State Drive Product Manual Rev 1.1 9. Ordering information SDSA4XH-CCCG-YYYY SD SanDisk SA SATA 4 Generation: 3 X Form factor: A - Half 1.8" form factor, Standard SATA connector B - Half 1.8" form factor, Standard SATA connector with large screw hole D - mSATA form factor E - Half 1.8" form factor, micro SATA connector F - mSATA Mini form factor G - 2.5" / 7mm cased product H Flash Memory used: 32nm 32Gb MLC ABL CCC Capacity: 004 008 016 032 064 128 G Units: GB YYYY Customer code reference Table 9-1: Ordering Information Refer to the examples below as reference for ordering SKUs. SKU # Details SDSA4AH-032G-YYYY 32GB SSD P4 in Half 1.8" form factor, Standard SATA connector SDSA4DH-064G-YYYY 64GB SSD P4 in mSATA form factor SDSA4EH-128G-YYYY 128GB SSD P4 in Half 1.8" form factor, Micro-SATA connector SDSA4FH-016G-YYYY 16GB SSD P4 in mSATA Mini form factor Table 9-2: Examples of decoded SKU (c) 2010 SanDisk(R) Corporation 51 Document No. 80-11-XXXX1 SSD P4 Solid State Drive 10. Product Manual Rev 1.1 Contact information USA Tel: +1-408-470-4440 Fax: +1-408-470-4470 OEMinfo@sandisk.com China Tel: +86-755-8348-5218 Fax: +86-755-8348-5418 OEMChina@sandisk.com Taiwan Tel: +886-2-2515-2522 Fax: +886-2-2515-2295 OEMAsia@sandisk.com Korea Tel: +82-2-3452-9079 Fax: +82-2-3452-9145 Japan Tel: +81-3-5423-8101 Fax: +81-3-5423-8102 OEMJapan@sandisk.com Europe Tel: +33-(1)-43-37-2131 Fax: +33-(1)-43-37-2111 OEMEurope@sandisk.com Rest of the World & Israel Tel: +972-9-764-5000 Fax: +972-3-548-8666 For more information, please visit www.sandisk.com/SSD (c) 2010 SanDisk(R) Corporation 52 Document No. 80-11-XXXX1