Data Sheet 26182.124B 6809 AND 6810 DABiC-IV, 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS A6810xA OUT 8 1 18 OUT 9 OUT 7 2 17 OUT 10 OUT 6 3 16 SERIAL DATA OUT CLOCK 4 GROUND 5 LATCHES CLK REGISTER VBB 15 LOAD SUPPLY REGISTER 14 SERIAL DATA IN LATCHES LOGIC SUPPLY 6 VDD STROBE 7 ST OUT 5 OUT 4 BLNK 13 BLANKING 12 OUT 1 8 11 OUT 2 9 10 OUT 3 Dwg. PP-029 ABSOLUTE MAXIMUM RATINGS at TA = 25C Logic Supply Voltage, VDD ................... 7.0 V Driver Supply Voltage, VBB ................... 60 V Continuous Output Current Range, IOUT ......................... -40 mA to +15 mA Input Voltage Range, VIN ....................... -0.3 V to VDD + 0.3 V Package Power Dissipation, PD ........................................ See Graph Operating Temperature Range, TA (Suffix `E-') .................. -40C to +85C (Suffix `S-') .................. -20C to +85C Storage Temperature Range, TS ............................... -55C to +125C Caution: These CMOS devices have input static protection (Class 2) but are still susceptible to damage if exposed to extremely high static electrical charges. The A6809- and A6810- devices combine 10-bit CMOS shift registers, accompanying data latches and control circuitry with bipolar sourcing outputs and pnp active pull downs. Designed primarily to drive vacuum-fluorescent displays, the 60 V and -40 mA output ratings also allow these devices to be used in many other peripheral power driver applications. The A6809- and A6810- feature an increased data input rate (compared with the older UCN/UCQ5810-F) and a controlled output slew rate. The A6809xLW and A6810xLW are identical except for pinout. The CMOS shift register and latches allow direct interfacing with microprocessor-based systems. With a 3.3 V or 5 V logic supply, typical serial-data input rates are up to 33 MHz. A CMOS serial data output permits cascade connections in applications requiring additional drive lines. Similar devices are avail-able as the A6811- (12 bits), A6812- (20 bits), and A6818- (32 bits). The A6809- and A6810- output source drivers are npn Darlingtons, capable of sourcing up to 40 mA. The controlled output slew rate reduces electromagnetic noise, which is an important consideration in systems that include telecommunications and/or microprocessors and to meet government emissions regulations. For inter-digit blanking, all output drivers can be disabled and all sink drivers turned on with a BLANKING input high. The pnp active pull-downs will sink at least 2.5 mA. All devices are available in two temperature ranges for optimum performance in commercial (suffix S-) or industrial (suffix E-) applications. The A6810- is provided in three package styles for through-hole DIP (suffix -A), surface-mount SOIC (suffix -LW), or minimum-area surface-mount PLCC (suffix -EP). The A6809- is provided in the SOIC (suffix -LW) only. Copper lead frames, low logic-power dissipation, and low output-saturation voltages allow all devices to source 25 mA from all outputs continuously over the maximum operating temperature range. FEATURES Controlled Output Slew Rate Low Output-Saturation Voltages High-Speed Data Storage Low-Power CMOS Logic 60 V Minimum and Latches Output Breakdown Improved Replacements High Data Input Rate for TL4810-, UCN5810-, PNP Active Pull-Downs and UCQ5810- Complete part number includes a suffix to identify operating temperature range (E- or S-) and package type (-A, -EP, or -LW). Always order by complete part number, e.g., A6810SLW . 6809 AND 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS TYPICAL OUTPUT DRIVER V TYPICAL INPUT CIRCUIT VDD BB OUTN IN Dwg. EP-021-19 A6809xLW Dwg. EP-010-5 OUT 10 OUT 6 3 LOGIC SUPPLY 7 VDD STROBE 8 ST OUT 5 OUT 4 REGISTER LOAD SUPPLY 15 SERIAL DATA IN CLOCK 4 NC 5 GROUND 6 LOGIC SUPPLY 7 STROBE 8 18 CLK LATCHES LATCHES BLNK 14 BLANKING 13 OUT 1 9 12 OUT 2 10 11 OUT 3 V BB 17 REGISTER NC 15 SERIAL DATA IN LATCHES BLNK 14 ST Dwg. PP-029-9 LOAD SUPPLY 16 REGISTER V DD SERIAL DATA OUT BLANKING 13 NC 16 OUT1 6 BB SERIAL DATA OUT 12 NO CONNECTION V 17 11 5 REGISTER 10 GROUND CLK 9 4 OUT 5 CLOCK NO CONNECTION 3 NC 18 LATCHES A6810xEP OUT10 19 19 2 20 OUT 7 1 OUT 9 2 20 OUT 6 OUT 8 1 Dwg. PP-059 OUT 8 1 20 OUT 9 OUT 7 2 19 OUT 10 OUT 6 3 18 SERIAL DATA OUT CLOCK 4 LATCHES CLK GROUND 5 LOGIC SUPPLY 6 VDD STROBE 7 ST OUT 5 OUT 4 REGISTER VBB 17 REGISTER 16 LATCHES NO CONNECTION BLNK 15 LOAD SUPPLY SERIAL DATA IN BLANKING 14 OUT 1 8 13 OUT 2 9 12 OUT 3 10 NC NC 11 NO CONNECTION ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS A6810xLW 2.5 SUFFIX 'EP', R JA = 59C/W 2.0 SUFFIX 'A', R JA = 60C/W 1.5 1.0 0.5 SUFFIX 'LW', R JA = 70C/W 0 25 50 75 100 125 AMBIENT TEMPERATURE IN C Dwg. PP-029-2 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright (c) 1998, 2000 Allegro MicroSystems, Inc. 150 Dwg. GP-024-1 6809 AND 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FUNCTIONAL BLOCK DIAGRAM LOGIC SUPPLY V DD CLOCK SERIAL DATA IN SERIAL-PARALLEL SHIFT REGISTER STROBE LATCHES SERIAL DATA OUT BLANKING MOS BIPOLAR LOAD SUPPLY VBB GROUND OUT 1 OUT 2 OUT 3 OUT N Dwg. FP-013-1 TRUTH TABLE Serial Shift Register Contents Data Clock Input Input I1 I2 I3 ... IN-1 IN Serial Data Strobe Output Input Latch Contents I1 I2 I3 ... Output Contents IN-1 IN Blanklng I1 I2 I3 ... IN-1 IN H H R1 R2 ... RN-2 RN-1 RN-1 L L R1 R2 ... RN-2 RN-1 RN-1 X R1 R2 R3 ... RN-1 RN RN X X X L R1 R2 R3 ... RN-1 RN PN H P1 P2 P3 ... PN-1 PN L P1 P2 P3 ... PN-1 PN X X H L X X ... P1 P2 P3 ... L = Low Logic Level X PN-1 PN H = High Logic Level www.allegromicro.com X = Irrelevant X P = Present State X ... X R = Previous State L L ... L L 6809 AND 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS ELECTRICAL CHARACTERISTICS at TA = +25C (A6809SLW & A6810S-) or over operating temperature range (A6809ELW & A6810E-), VBB = 60 V unless otherwise noted. Limits @ VDD = 3.3 V Characteristic Output Leakage Current Symbol ICEX Test Conditions VOUT = 0 V Limits @ VDD = 5 V Mln. Typ. Max. Min. Typ. Max. Units -- <-0.1 -15 -- <-0.1 -15 A 57.5 58.3 -- 57.5 58.3 -- V VOUT(1) IOUT = -25 mA VOUT(0) IOUT = 1 mA -- 1.0 1.5 -- 1.0 1.5 V Output Pull-Down Current IOUT(0) VOUT = 5 V to VBB 2.5 5.0 -- 2.5 5.0 -- mA Input Voltage VIN(1) 2.2 -- -- 3.3 -- -- V VIN(0) -- -- 1.1 -- -- 1.7 V Output Voltage Input Current Input Clamp Voltage Serial Data Output Voltage Maximum Clock Frequency Logic Supply Current IIN(1) VIN = VDD -- <0.01 1.0 -- <0.01 1.0 A IIN(0) VIN = 0 V -- <-0.01 -1.0 -- <-0.01 -1.0 A IIN = -200 A -- -0.8 -1.5 -- -0.8 -1.5 V VOUT(1) IOUT = -200 A 2.8 3.05 -- 4.5 4.75 -- V VOUT(0) IOUT = 200 A -- 0.15 0.3 -- 0.15 0.3 V 10 33 -- 10 33 -- MHz VIK fc IDD(1) All Outputs High -- 0.25 0.75 -- 0.3 1.0 mA IDD(0) All Outputs Low -- 0.25 0.75 -- 0.3 1.0 mA IBB(1) All Outputs High, No Load -- 1.5 3.0 -- 1.5 3.0 mA IBB(0) All Outputs Low -- 0.2 20 -- 0.2 20 A tdis(BQ) CL = 30 pF, 50% to 50% -- 0.7 2.0 -- 0.7 2.0 s ten(BQ) CL = 30 pF, 50% to 50% -- 1.8 3.0 -- 1.8 3.0 s tp(STH-QL) RL = 2.3 k, CL 30 pF -- 0.7 2.0 -- 0.7 2.0 s tp(STH-QH) RL = 2.3 k, CL 30 pF -- 1.8 3.0 -- 1.8 3.0 s Output Fall Time tf RL = 2.3 k, CL 30 pF 2.4 -- 12 2.4 -- 12 s Output Rise Time tr RL = 2.3 k, CL 30 pF 2.4 -- 12 2.4 -- 12 s Output Slew Rate dV/dt RL = 2.3 k, CL 30 pF 4.0 -- 20 4.0 -- 20 V/s IOUT = 200 A -- 50 -- -- 50 -- ns Load Supply Current Blanking-to-Output Delay Strobe-to-Output Delay Clock-to-Serial Data Out Delay tp(CH-SQX) Negative current is defined as coming out of (sourcing) the specified device terminal. Typical data is is for design information only and is at TA = +25C. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6809 AND 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS TIMING REQUIREMENTS and SPECIFICATIONS (Logic Levels are VDD and Ground) C 50% CLOCK A SERIAL DATA IN B DATA 50% t p(CH-SQX) SERIAL DATA OUT DATA 50% D 50% STROBE BLANKING E LOW = ALL OUTPUTS ENABLED t p(STH-QH) t p(STH-QL) 90% DATA OUT N 10% Dwg. WP-029 HIGH = ALL OUTPUTS BLANKED (DISABLED) BLANKING 50% t dis(BQ) t en(BQ) tr tf 90% OUT N A. Data Active Time Before Clock Pulse (Data Set-Up Time), tsu(D) ......................................... 25 ns B. Data Active Time After Clock Pulse (Data Hold Time), th(D) ............................................... 25 ns C. Clock Pulse Width, tw(CH) ............................................... 50 ns 10% DATA Dwg. WP-030 NOTE - Timing is representative of a 10 MHz clock. Significantly higher speeds are attainable. Information present at any register is transferred to the respective latch when the STROBE is high (serial-to-parallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the BLANKING input be high during serial data entry. Serial Data present at the input is transferred to the shift register on the logic "0" to logic "1" transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data information towards the SERIAL DATA OUTPUT. The SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform. When the BLANKING input is high, the output source drivers are disabled (OFF); the pnp active pull-down sink drivers are ON. The information stored in the latches is not affected by the BLANKING input. With the BLANKING input low, the outputs are controlled by the state of their respective latches. D. Time Between Clock Activation and Strobe, tsu(C) ....... 100 ns E. Strobe Pulse Width, tw(STH) ............................................. 50 ns www.allegromicro.com 6809 AND 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS A6810EA & A6810SA Dimensions in Inches (controlling dimensions) 18 0.014 0.008 10 0.430 MAX 0.280 0.240 0.300 BSC 1 0.070 0.045 0.100 0.920 0.880 9 0.005 BSC MIN 0.210 MAX 0.150 0.115 0.015 MIN 0.022 0.014 Dwg. MA-001-18A in Dimensions in Millimeters (for reference only) 18 0.355 0.204 10 10.92 MAX 7.11 6.10 7.62 BSC 1 1.77 1.15 2.54 23.37 22.35 9 0.13 BSC MIN 5.33 MAX 3.81 2.93 0.39 MIN 0.558 0.356 Dwg. MA-001-18A mm NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Lead thickness is measured at seating plane or below. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 6809 AND 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS A6810EEP & A6810SEP Dimensions in Inches (controlling dimensions) 13 9 0.021 0.013 8 14 0.169 0.141 0.395 0.385 0.032 0.026 INDEX AREA 0.356 0.350 0.050 0.169 0.141 BSC 18 4 19 20 1 2 3 0.356 0.350 0.020 MIN 0.395 0.385 0.180 0.165 Dimensions in Millimeters (for reference only) Dwg. MA-005-20A in 13 9 0.533 0.331 10.03 9.78 0.812 0.661 INDEX AREA 9.042 8.890 1.27 4.29 3.58 8 14 4.29 3.58 BSC 18 4 19 0.51 MIN 4.57 4.20 20 1 2 3 9.042 8.890 10.03 9.78 Dwg. MA-005-20A mm The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. www.allegromicro.com The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. 6809 AND 6810 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS A6809ELW, A6809SLW, A6810ELW, & A6810SLW Dimensions in Inches (for reference only) 20 11 0.0125 0.0091 0.419 0.394 0.2992 0.2914 0.050 0.016 0.020 0.013 1 2 0.050 3 0 TO 8 BSC 0.5118 0.4961 0.0926 0.1043 0.0040 MIN. Dwg. MA-008-20 in Dimensions in Millimeters (controlling dimensions) 20 11 0.32 0.23 10.65 10.00 7.60 7.40 1.27 0.40 0.51 0.33 1 2 1.27 3 13.00 12.60 BSC 0 TO 8 2.65 2.35 0.10 MIN. Dwg. MA-008-20 mm NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Lead spacing tolerance is non-cumulative. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000