GE
Data Sheet
January 14, 2016 ©2016 General Electric Company. All rights reserved.
12V Austin SuperLynxTM II: SMT Non-Isolated DC-DC Power Module
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
Features
Compliant to RoHS EU Directive 2011/65/EU (-Z
versions)
Compliant to RoHS EU Directive 2011/65/EU under
exemption 7b (Lead solder exemption). Exemption 7b
will expire after June 1, 2016 at which time this product
will no longer be RoHS compliant (non-Z versions)
Flexible output voltage sequencing EZ-SEQUENCETM
Delivers up to 16A output current
High efficiency – 92% at 3.3V full load (VIN = 12.0V)
Small size and low profile:
33.0 mm x 13.5 mm x 8.28 mm
(1.30 in x 0.53 in x 0.326 in)
Low output ripple and noise
High Reliability:
Calculated MTBF = 9.2M hours at 25oC Full-load
Output voltage programmable from 0.75 Vdc to 5.5Vdc
via external resistor
Line Regulation: 0.3% (typical)
Load Regulation: 0.4% (typical)
Temperature Regulation: 0.4 % (typical)
Remote On/Off
Remote Sense
Output overcurrent protection (non-latching)
Wide operating temperature range (-40°C to 85°C)
UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03
Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed
ISO** 9001 and ISO 14001 certified manufacturing
facilities
Applications
Distributed power architectures
Intermediate bus voltage applications
Telecommunications equipment
Servers and storage applications
Networking equipment
Enterprise Networks
Latest generation IC’s (DSP, FPGA, ASIC) and
Microprocessor powered applications
Description
Austin SuperLynxTM II 12V SMT power modules are non-isolated DC-DC converters that can deliver up to 16A of output
current with full load efficiency of 92% at 3.3V output. These modules provide a precisely regulated output voltage
programmable via an external resistor from 0.75Vdc to 5.5Vdc over a wide range of input voltage (VIN = 8.3 – 14Vdc).
Austin SuperLynxTM II has a sequencing feature, EZ-SEQUENCETM that enable designers to implement various types of
output voltage sequencing when powering multiple modules on board.
* UL is a registered trademark of Underwriters Laboratories, Inc.
† CSA is a registered trademark of Canadian Standards Association.
‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
RoHS Compliant
EZ-SEQUENCETM
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
2
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings
only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations
sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability.
Parameter Device Symbol Min Max Unit
Input Voltage All VIN -0.3 15 Vdc
Continuous
Sequencing voltage All Vseq -0.3 VIN,max Vdc
Operating Ambient Temperature All TA -40 85 °C
(see Thermal Considerations section)
Storage Temperature All Tstg -55 125 °C
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage Vo,set ≤ 3.63 VIN 8.3 12.0 14.0 Vdc
Vo,set > 3.63 VIN 8.3 12.0 13.2 Vdc
Maximum Input Current All IIN,max 10 Adc
(VIN= VIN, min to VIN, max, IO=IO, max )
Input No Load Current Vo = 0.75Vdc IIN,No load 40 mA
(VIN = VIN, nom, Io = 0, module enabled) Vo = 5.0Vdc IIN,No load 100 mA
Input Stand-by Current All IIN,stand-by 2 mA
(VIN = VIN, nom, module disabled)
Inrush Transient All I2t 0.4 A2s
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 1μH source impedance; VIN, min to VIN,
max, IO= IOmax ; See Test configuration section)
All 30 mAp-p
Input Ripple Rejection (120Hz) All 30 dB
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a
complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety
and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 15 A
(see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input
current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data sheet for further information.
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
3
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Output Voltage Set-point All VO, set -2.0 VO, set +2.0 % VO, set
(VIN=IN, min, IO=IO, max, TA=25°C)
Output Voltage All VO, set -2.5% +3.5% % VO, set
(Over all operating input voltage, resistive load, and
temperature conditions until end of life)
Adjustment Range All VO 0.7525 5.5 Vdc
Selected by an external resistor
Output Regulation
Line (VIN=VIN, min to VIN, max) All 0.3 % VO, set
Load (IO=IO, min to IO, max) All 0.4 % VO, set
Temperature (Tref=TA, min to TA, max) All 0.4 % VO, set
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max
Cout = 1μF ceramic//10μFtantalum capacitors)
RMS (5Hz to 20MHz bandwidth) All 12 30 mVrms
Peak-to-Peak (5Hz to 20MHz bandwidth) All 30 75 mVpk-pk
External Capacitance
ESR ≥ 1 mΩ All CO, max 1000 μF
ESR ≥ 10 mΩ All CO, max 5000 μF
Output Current All Io 0 16 Adc
Output Current Limit Inception (Hiccup Mode ) All IO, lim 180 % Io
(VO= 90% of VO, set)
Output Short-Circuit Current All IO, s/c 3 Adc
(VO≤250mV) ( Hiccup Mode )
Efficiency
V
O, set
=
0.75Vdc
η 79.0 %
VIN= VIN, nom, TA=25°C
V
O, set
=
1 2Vdc
η 85.0 %
IO=IO, max , VO= VO,set
V
O,set
=
1 5Vdc
η 87.0 %
V
O,set
=
1 8Vdc
η 88.0 %
V
O,set
=
2 5Vdc
η 90.5 %
V
O,set
=
3 3Vdc
η 92.0 %
V
O,set
=
5 0Vdc
η 94.0 %
Switching Frequency All fsw 300 kHz
Dynamic Load Response
(dIo/dt=2.5A/µs; VIN = VIN, nom; TA=25°C) All Vpk 200 mV
Load Change from Io= 50% to 100% of Io,max; 1μF
ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts 25 µs
(dIo/dt=2.5A/µs; VIN = VIN, nom; TA=25°C) All Vpk 200 mV
Load Change from Io= 100% to 50%of Io,max: 1μF
ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts 25 µs
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
4
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Dynamic Load Response
(dIo/dt=2.5A/µs; V VIN = VIN, nom; TA=25°C) All Vpk 100 mV
Load Change from Io= 50% to 100% of Io,max;
Co = 2x150 μF polymer capacitors
Peak Deviation
Settling Time (Vo<10% peak deviation)
All ts 50 µs
(dIo/dt=2.5A/µs; VIN = VIN, nom; TA=25°C) All Vpk 100 mV
Load Change from Io= 100% to 50%of Io,max:
Co = 2x150 μF polymer capacitors
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts 50 µs
General Specifications
Parameter Min Typ Max Unit
Calculated MTBF (IO=IO, max, TA=25°C) 9,230,550 Hours
Telecordia SR-332 Issue 1: Method 1 Case 3
Weight 5.6 (0.2) g (oz.)
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
5
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See
Feature Descriptions for additional information.
Parameter Device Symbol Min Typ Max Unit
On/Off Signal interface
Device code with Suffix “4” – Positive logic
(On/Off is open collector/drain logic input;
Signal referenced to GND - See feature description section)
Input High Voltage (Module ON) All VIH ― ― VIN, max V
Input High Current All IIH ― ― 10 μA
Input Low Voltage (Module OFF) All VIL -0.2 ― 0.3 V
Input Low Current All IIL ― 0.2 1 mA
Device Code with no suffix – Negative Logic
(On/OFF pin is open collector/drain logic input with
external pull-up resistor; signal referenced to GND)
Input High Voltage (Module OFF) All VIH 2.5 ― VIN,max Vdc
Input High Current All IIH 0.2 1 mA
Input Low Voltage (Module ON) All VIL -0.2 ― 0.3 Vdc
Input low Current All IIL ― 10 μA
Turn-On Delay and Rise Times
(IO=IO, max , VIN = VIN, nom, TA = 25 oC, )
Case 1: On/Off input is set to Logic Low (Module
ON) and then input power is applied (delay from
instant at which VIN =VIN, min until Vo=10% of Vo,set)
All
Tdelay
―
3
―
msec
Case 2: Input power is applied for at least one second
and then the On/Off input is set to logic Low (delay from
instant at which Von/Off=0.3V until Vo=10% of Vo, set)
All
Tdelay
―
3
―
msec
Output voltage Rise time (time for Vo to rise from 10%
of Vo,set to 90% of Vo, set)
All
Trise
―
4
6
msec
Output voltage overshoot – Startup ―
1
% VO, set
IO= IO, max; VIN = 8.3 to 14Vdc, TA = 25 oC
Remote Sense Range All ― ― 0.5 V
Sequencing Delay time
Delay from VIN, min to application of voltage on SEQ pin All TsEQ-delay 10 msec
Tracking Accuracy (Power-Up: 2V/ms) All |VSEQ –Vo | 100 200 mV
(Power-Down: 1V/ms) All |VSEQ –Vo | 300 500 mV
(VIN, min to VIN, max; IO, min to IO, max VSEQ < Vo)
Overtemperature Protection
All Tref 125 °C
(See Thermal Consideration section)
Input Undervoltage Lockout
Turn-on Threshold All 7.9 V
Turn-off Threshold All 7.8 V
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
6
Characteristic Curves
The following figures provide typical characteristics for the Austin SuperLynxTM II 12V SMT modules at 25ºC.
EFFICIENCY, (η)
70
72
74
76
78
80
82
84
86
88
90
0 4 8 12 16
Vin=14V
Vin=10V
Vin=12V
EFFICIENCY, (η)
74
76
78
80
82
84
86
88
90
92
94
04812 16
Vin=14V
Vin=10V
Vin=12V
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, IO (A)
Figure 1. Converter Efficiency versus Output Current (Vout
= 1.2Vdc).
Figure 4. Converter Efficiency versus Output Current
(Vout = 2.5Vdc).
EFFICIENCY, (η)
70
72
74
76
78
80
82
84
86
88
90
04 8 12 16
Vin=14V
Vin=10V
Vin=12V
EFFICIENCY, (η)
74
76
78
80
82
84
86
88
90
92
94
0 4 8 12 16
Vin=14V
Vin=10V
Vin=12V
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, IO (A)
Figure 2. Converter Efficiency versus Output Current (Vout
= 1.5Vdc).
Figure 5. Converter Efficiency versus Output Current
(Vout = 3.3Vdc).
EFFICIENCY, (η)
72
74
76
78
80
82
84
86
88
90
92
0 4 8 12 16
Vin=14V
Vin=10V
Vin=12V
EFFICIENCY, (η)
74
76
78
80
82
84
86
88
90
92
94
96
0 4 8 12 16
Vin=14V
Vin=10V
Vin=12V
OUTPUT CURRENT, I
O
(A)
OUTPUT CURRENT, I
O
(A)
Figure3. Converter Efficiency versus Output Current (Vout
= 1.8Vdc).
Figure 6. Converter Efficiency versus Output Current
(Vout =5.0Vdc).
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
7
Characteristic Curves (continued)
The following figures provide typical characteristics for the SuperLynxTM II 12V SMT modules at 25ºC.
INPUT CURRENT, IIN (A)
0
1
2
3
4
5
6
7
8
9
7 8 910 11 12 13 14
Io = 16A
Io=8A
Io=0A
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (200mV/div)
INPUT VOLTAGE, V
IN
(V)
TIME, t (5µs/div)
Figure 7. Input Voltage vs. Input Current
(Vo = 3.3 Vdc).
Figure 10. Transient Response to Dynamic Load Change
from 50% to 100% of full load (Vo = 3.3Vdc).
OUTPUT VOLTAGE
VO (V) (20mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (200mV/div)
TIME, t (2µs/div)
TIME, t (5µs/div)
Figure 8. Typical Output Ripple and Noise
(Vin = 12V dc, Vo = 2.5 Vdc, Io=16A).
Figure 11. Transient Response to Dynamic Load Change
from 100% to 50% of full load (Vo = 3.3Vdc).
OUTPUT VOLTAGE
VO (V) (20mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (100mV/div)
TIME, t (2µs/div)
TIME, t (10µs/div)
Figure 9. Typical Output Ripple and Noise
(Vin = 12V dc, Vo = 3.3Vdc, Io=16A).
Figure 12. Transient Response to Dynamic Load Change
from 50% to 100% of full load (Vo =3.3Vdc, Cext = 2x150
μF Polymer Capacitors).
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
8
Characteristic Curves (continued)
The following figures provide typical characteristics for the Austin SuperLynxTM II 12V SMT modules at 25ºC.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (100mV/div)
OUTPUT VOLTAGE, INPUT VOLTAGE Vo (V)
(2V/div) VIN (V) (5V/div)
TIME, t (10µs/div)
TIME, t (2 ms/div)
Figure 13. Transient Response to Dynamic Load Change
from 100% of 50% full load (Vo = 3.3Vdc, Cext = 2x150 μF
Polymer Capacitors)
Figure 16. Typical Start-Up with application of Vin with
low-ESR polymer capacitors at the output (7x150 μF) (Vin
= 12Vdc, Vo = 5.0Vdc, Io = 16A, Co = 1050 μF).
OUTPUT VOLTAGE On/Off VOLTAGE
VOV) (2V/div) VOn/off (V) (5V/div)
OUTPUT VOLTAGE
VOV) (1V/div)
TIME, t 2ms/div)
TIME, t (2ms/div)
Figure 14. Typical Start-Up Using Remote On/Off
(Vin = 12Vdc, Vo = 5.0Vdc, Io =16A).
Figure 17. Typical Start-Up with Prebias (Vin = 12Vdc, Vo
= 2.5Vdc, Io = 1A, Vbias =1.2 Vdc).
OUTPUT VOLTAGE On/Off VOLTAGE
VOV) (2V/div) VOn/off (V) (5V/div)
OUTPUT CURRENT,
IO (A) (10A/div)
TIME, t (2ms/div)
TIME, t (10ms/div)
Figure 15. Typical Start-Up Using Remote On/Off with Low-
ESR external capacitors (7x150uF Polymer)
(Vin = 12Vdc, Vo = 5.0Vdc, Io = 16A, Co = 1050µF).
Figure 18. Output short circuit Current
(Vin = 12Vdc, Vo = 0.75Vdc).
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
9
Characteristic Curves (continued)
The following figures provide thermal derating curves for the Austin SuperLynxTM II 12V SMT modules.
OUTPUT CURRENT, Io (A)
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
OUTPUT CURRENT, Io (A)
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
AMBIENT TEMPERATURE, TA
O
C
AMBIENT TEMPERATURE, TA
O
C
Figure 19. Derating Output Current versus Local Ambient
Temperature and Airflow (Vin = 12Vdc, Vo=0.75Vdc).
Figure 22. Derating Output Current versus Local Ambient
Temperature and Airflow (Vin = 12dc, Vo=5.0 Vdc).
OUTPUT CURRENT, Io (A)
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
AMBIENT TEMPERATURE, TA
O
C
Figure 20. Derating Output Current versus Local Ambient
Temperature and Airflow (Vin = 12Vdc, Vo=1.8 Vdc).
OUTPUT CURRENT, Io (A)
0
2
4
6
8
10
12
14
16
18
20 30 40 50 60 70 80 90
100 LFM
200 LFM
NC
300 LFM
400 LFM
AMBIENT TEMPERATURE, T
A
O
C
Figure 21. Derating Output Current versus Local Ambient
Temperature and Airflow (Vin = 12Vdc, Vo=3.3 Vdc).
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
10
Test Configurations
TO OSCILLOSCOPE
CURRENT PROBE
L
TEST
1μH
BATTERY
C
S
1000μF
Electrolytic
E.S.R.<0.1Ω
@ 20°C 100kHz
2x100μF
Tantalum
V
IN
(+)
COM
NOTE: Measure input ref l ect ed ripple current with a sim ulated
source inductance (LTEST) of 1μH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
C
IN
Figure 23. Input Reflected Ripple Current Test Setup.
NOTE: All voltage measurem ents to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
V
O
(+)
COM
1uF
.
RESISTIVE
LOAD
SCOPE
COPPER STRIP
GROUND PLANE
10uF
Figure 24. Output Ripple and Noise Test Setup.
V
O
COM
V
IN
(+)
COM
R
LOAD
R
contact
R
distribution
R
contact
R
distribution
R
contact
R
contact
R
distribution
R
distribution
V
IN
V
O
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvi n c onnec ti ons are r equ ir ed at th e m odu le termin als
to avoi d m eas urem en t errors du e to s ock et c ont act
resistance.
Figure 25. Output Voltage and Efficiency Test Setup.
η
=
V
O
.
I
O
V
IN
.
I
IN
x
100
%
Efficiency
Design Considerations
Input Filtering
Austin SuperLynxTM II 12V SMT module should be connected
to a low-impedance source. A highly inductive source can
affect the stability of the module. An input capacitance
must be placed directly adjacent to the input pin of the
module, to minimize input ripple voltage and ensure
module stability.
In a typical application, 6x47 µF low-ESR tantalum
capacitors (AVX part #: TPSE476M025R0100, 47µF 25V 100
mΩ ESR tantalum capacitor) will be sufficient to provide
adequate ripple voltage at the input of the module. To
further minimize ripple voltage at the input, very low ESR
ceramic capacitors are recommended at the input of the
module. Figure 26 shows input ripple voltage (mVp-p) for
various outputs with 6x47 µF tantalum capacitors and with
6x22 µF ceramic capacitor (TDK part #: C4532X5R1C226M)
at full load.
Input Ripple Voltage (mVp-p)
0
50
100
150
200
250
300
350
0 1 2 3 4 5 6
Tantalum
Ceramic
Output Voltage (Vdc)
Figure 26. Input ripple voltage for various output with 6x47
µF tantalum capacitors and with 6x22 µF ceramic capacitors
at the input (full load).
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
11
Design Considerations (continued)
Output Filtering
The Austin SuperLynxTM II 12V SMT module is designed for low
output ripple voltage and will meet the maximum output ripple
specification with 1 µF ceramic and 10 µF tantalum capacitors
at the output of the module. However, additional output
filtering may be required by the system designer for a number
of reasons. First, there may be a need to further reduce the
output ripple and noise of the module. Second, the dynamic
response characteristics may need to be customized to a
particular load step change.
To reduce the output ripple and improve the dynamic response
to a step load change, additional capacitance at the output
can be used. Low ESR polymer and ceramic capacitors are
recommended to improve the dynamic response of the
module. For stable operation of the module, limit the
capacitance to less than the maximum output capacitance as
specified in the electrical specification table.
Safety Considerations
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards, i.e., UL
60950-1, CSA C22.2 No. 60950-1-03, and VDE 0850:2001-12
(EN60950-1) Licensed.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the input
must meet SELV requirements. The power module has extra-
low voltage (ELV) outputs when all inputs are ELV.
The input to these units is to be provided with a fast-acting
fuse with a maximum rating of 15A in the positive input lead.
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
12
Feature Description
Remote On/Off
Austin SuperLynxTM II 12V SMT power modules feature an
On/Off pin for remote On/Off operation. Two On/Off logic
options are available in the Austin SuperLynxTM II series
modules. Positive Logic On/Off signal, device code suffix “4”,
turns the module ON during a logic High on the On/Off pin and
turns the module OFF during a logic Low. Negative logic
On/Off signal, no device code suffix, turns the module OFF
during logic High and turns the module ON during logic Low.
For positive logic modules, the circuit configuration for using
the On/Off pin is shown in Figure 27. The On/Off pin is an open
collector/drain logic input signal (Von/Off) that is referenced to
ground. During a logic-high (On/Off pin is pulled high internal
to the module) when the transistor Q1 is in the Off state, the
power module is ON. Maximum allowable leakage current of
the transistor when Von/off = VIN,max is 10µA. Applying a logic-
low when the transistor Q1 is turned-On, the power module is
OFF. During this state VOn/Off must be less than 0.3V. When
not using positive logic On/off pin, leave the pin unconnected
or tie to VIN.
Q1
R2
R1 Q2
R3
R4
Q3 CSS
GND
VIN+
ON/OFF
PW M Enable
+
_
ON/OFF
V
I
ON/OFF
MODULE
Figure 27. Circuit configuration for using positive logic
On/OFF.
For negative logic On/Off devices, the circuit configuration is
shown is Figure 28. The On/Off pin is pulled high with an
external pull-up resistor (typical Rpull-up = 68k, +/- 5%). When
transistor Q1 is in the Off state, logic High is applied to the
On/Off pin and the power module is Off. The minimum On/off
voltage for logic High on the On/Off pin is 2.5 Vdc. To turn the
module ON, logic Low is applied to the On/Off pin by turning
ON Q1. When not using the negative logic On/Off, leave the
pin unconnected or tie to GND.
Q1
R1
R2
Q2 CSS
GND
PW M Enable
ON/OFF
VIN+
ON/OFF
_
+
V
I
MODULE
pull-up
R
ON/OFF
Figure 28. Circuit configuration for using negative logic
On/OFF.
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally once
the output current is brought back into its specified range.
The typical average output current during hiccup is 3A.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout limit,
module operation is disabled. The module will begin to operate
at an input voltage above the undervoltage lockout turn-on
threshold.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with a thermal shutdown circuit. The unit will
shutdown if the thermal reference point Tref, exceeds 125oC
(typical), but the thermal shutdown is not intended as a
guarantee that the unit will survive temperatures beyond its
rating. The module will automatically restarts after it cools
down.
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
13
Feature Descriptions (continued)
Output Voltage Programming
The output voltage of the Austin SuperLynxTM II 12V can be
programmed to any voltage from 0.75Vdc to 5.5Vdc by
connecting a resistor (shown as Rtrim in Figure 29) between the
Trim and GND pins of the module. Without an external resistor
between the Trim and GND pins, the output of the module will
be 0.7525Vdc. To calculate the value of the trim resistor, Rtrim
for a desired output voltage, use the following equation:
Ω
−
−
=1000
7525.0
10500
Vo
Rtrim
Rtrim is the external resistor in Ω
Vo is the desired output voltage
For example, to program the output voltage of the Austin
SuperLynxTM II module to 1.8V, Rtrim is calculated as follows:
−
−
=1000
75
.08
.1
10500
Rtrim
Ω
=kRtrim 024.9
V
O
(+)
TRIM
GND
R
trim
LOAD
V
IN
(+)
ON/OFF
Figure 29. Circuit configuration to program output voltage
using an external resistor
Table 1 provides Rtrim values for most common output
voltages.
Table 1
V
O, set
(V)
Rtrim (KΩ)
0.7525
Open
1.2
22.46
1.5
13.05
1.8
9.024
2.5
5.009
3.3
3.122
5.0
1.472
By using 1% tolerance trim resistor, set point tolerance of ±2%
is achieved as specified in the electrical specification. The POL
Programming Tool, available at www.gecriticalpower.com
under the Design Tools section, helps determine the required
external trim resistor needed for a specific output voltage.
The amount of power delivered by the module is defined as
the voltage at the output terminals multiplied by the output
current. When using the trim feature, the output voltage of
the module can be increased, which at the same output
current would increase the power output of the module.
Care should be taken to ensure that the maximum output
power of the module remains at or below the maximum
rated power (Pmax = Vo,set x Io,max).
Voltage Margining
Output voltage margining can be implemented in the Austin
SuperLynxTM II modules by connecting a resistor, Rmargin-up, from
the Trim pin to the ground pin for margining-up the output
voltage and by connecting a resistor, Rmargin-down, from the Trim
pin to the Output pin for margining-down. Figure 30 shows the
circuit configuration for output voltage margining. The POL
Programming Tool, available at www.gecriticalpower.com
under the Design Tools section, also calculates the values of
Rmargin-up and Rmargin-down for a specific output voltage and %
margin. Please consult your local GE technical representative
for additional details.
Vo
Austin Lynx or
Lynx II Series
GND
Trim
Q1
Rtrim
Rmargin-up
Q2
Rmargin-down
Figure 30. Circuit Configuration for margining Output
voltage.
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
14
Feature Descriptions (continued)
Voltage Sequencing
Austin SuperLynxTM II 12V series of modules include a
sequencing feature, EZ-SEQUENCETM that enables users to
implement various types of output voltage sequencing in their
applications. This is accomplished via an additional
sequencing pin. When not using the sequencing feature, either
tie the SEQ pin to VIN or leave it unconnected.
When an analog voltage is applied to the SEQ pin, the output
voltage tracks this voltage until the output reaches the set-
point voltage. The SEQ voltage must be set higher than the
set-point voltage of the module. The output voltage follows the
voltage on the SEQ pin on a one-to-one volt basis. By
connecting multiple modules together, customers can get
multiple modules to track their output voltages to the voltage
applied on the SEQ pin.
For proper voltage sequencing, first, input voltage is applied to
the module. The On/Off pin of the module is left unconnected
(or tied to GND for negative logic modules or tied to VIN for
positive logic modules) so that the module is ON by default.
After applying input voltage to the module, a minimum of
10msec delay is required before applying voltage on the SEQ
pin. During this time, potential of 50mV (± 10 mV) is maintained
on the SEQ pin. After 10msec delay, an analog voltage is
applied to the SEQ pin and the output voltage of the module
will track this voltage on a one-to-one volt bases until output
reaches the set-point voltage. To initiate simultaneous
shutdown of the modules, the SEQ pin voltage is lowered in a
controlled manner. Output voltage of the modules tracks the
voltages below their set-point voltages on a one-to-one basis.
A valid input voltage must be maintained until the tracking and
output voltages reach ground potential to ensure a controlled
shutdown of the modules.
When using the EZ-SEQUENCETM feature to control start-up of
the module, pre-bias immunity feature during start-up is
disabled. The pre-bias immunity feature of the module relies
on the module being in the diode-mode during start-up. When
using the EZ-SEQUENCETM feature, modules goes through an
internal set-up time of 10msec, and will be in synchronous
rectification mode when voltage at the SEQ pin is applied. This
will result in sinking current in the module if pre-bias voltage is
present at the output of the module. When pre-bias immunity
during start-up is required, the EZ-SEQUENCETM feature must
be disabled. For additional guidelines on using EZ-SEQUENCETM
feature of Austin SuperLynxTM II 12V, contact GE technical
representative for preliminary application note on output
voltage sequencing using Austin Lynx II series.
Remote Sense
The Austin SuperLynxTM II 12V SMT power modules have a
Remote Sense feature to minimize the effects of distribution
losses by regulating the voltage at the Remote Sense pin (See
Figure 31). The voltage between the Sense pin and Vo pin must
not exceed 0.5V.
The amount of power delivered by the module is defined as the
output voltage multiplied by the output current (Vo x Io). When
using Remote Sense, the output voltage of the module can
increase, which if the same output is maintained, increases the
power output by the module. Make sure that the maximum
output power of the module remains at or below the maximum
rated power. When the Remote Sense feature is not being
used, connect the Remote Sense pin to output pin of the
module.
V
O
COM
V
IN
(+)
COM
R
LOAD
Rcontact
Rdistribution
Rcontact
Rdistribution
Rcontact
Rcontact
Rdistribution
Rdistribution
Sense
Figure 31. Remote sense circuit configuration.
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
15
Thermal Considerations
Power modules operate in a variety of thermal environments;
however, sufficient cooling should be provided to help ensure
reliable operation.
Considerations include ambient temperature, airflow, module
power dissipation, and the need for increased reliability. A
reduction in the operating temperature of the module will
result in an increase in reliability. The thermal data presented
here is based on physical measurements taken in a wind
tunnel. The test set-up is shown in Figure 33. Note that the
airflow is parallel to the long axis of the module as shown in
figure 32. The derating data applies to airflow in either
direction of the module’s long axis.
Figure 32. Tref Temperature measurement location.
The thermal reference points, Tref 1 and Tref2 used in the
specifications of thermal derating curves are shown in Figure
32. For reliable operation these temperatures should not
exceed 125oC.
The output power of the module should not exceed the rated
power of the module (Vo,set x Io,max).
Please refer to the Application Note “Thermal Characterization
Process For Open-Frame Board-Mounted Power Modules” for a
detailed discussion of thermal aspects including maximum
device temperatures.
Figure 33. Thermal Test Set-up.
Heat Transfer via Convection
Increased airflow over the module enhances the heat transfer
via convection. Thermal derating curves showing the
maximum output current that can be delivered by various
module versus local ambient temperature (TA) for natural
convection and up to 1m/s (200 ft./min) are shown in the
Characteristics Curves section.
Air
flow
x
Power Module
Wind Tunnel
PWBs
7.24_
(0.285)
76.2_
(3.0)
Probe Location
for measuring
airflo w and
ambient
temperature
25.4_
(1.0)
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
16
Mechanical Outline
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
Top View
Side View
Bottom View
PIN
FUNCTION
1
On/Off
2
V
IN
3
SEQ
4
GND
5
V
OUT
6
Trim
7
Sense
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
17
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
Surface Mount Pad Layout – Component side view.
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
18
Packaging Details
The Austin SuperLynxTM II 12V SMT versions are supplied in tape & reel as standard. Modules are shipped in quantities of 250
modules per reel.
All Dimensions are in millimeters and (in inches).
Reel Dimensions
Outside Dimensions: 330.2 mm (13.00)
Inside Dimensions: 177.8 mm (7.00”)
Width 44.0 mm (1.73”)
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
19
Surface Mount Information
Pick and Place
The Austin SuperLynxTM II 12V SMT modules use open frame
construction and are designed for fully a automated
assembly process. The modules are fitted with a label
designed to provide a large surface area for pick and place
operations. The label meets all the requirements for surface
mount processing, as well as safety standards, and is able to
withstand reflow temperatures of up to 300oC. The label
also carries product information such as product code, serial
number and location of manufacture.
Figure 34. Pick and Place Location.
Nozzle Recommendations
The module weight has been kept to a minimum by using
open frame construction. Even so, these modules have a
relatively large mass when compared to conventional SMT
components. Variables such as nozzle size, tip style,
vacuum pressure and pick & placement speed should be
considered to optimize this process. The minimum
recommended nozzle diameter for reliable operation is
3mm. The maximum nozzle outer diameter, which will safely
fit within the allowable component spacing, is 8 mm max.
Tin Lead Soldering
The Austin SuperLynxTM II 12V SMT power modules are lead
free modules and can be soldered either in a lead-free
solder process or in a conventional Tin/Lead (Sn/Pb) process.
It is recommended that the customer review data sheets in
order to customize the solder reflow profile for each
application board assembly. The following instructions must
be observed when soldering these units. Failure to observe
these instructions may result in the failure of or cause
damage to the modules, and can adversely affect long-term
reliability.
In a conventional Tin/Lead (Sn/Pb) solder process peak
reflow temperatures are limited to less than 235oC.
Typically, the eutectic solder melts at 183oC, wets the land,
and subsequently wicks the device connection. Sufficient
time must be allowed to fuse the plating on the connection
to ensure a reliable solder joint. There are several types of
SMT reflow technologies currently used in the industry.
These surface mount power modules can be reliably
soldered using natural forced convection, IR (radiant
infrared), or a combination of convection/IR. For reliable
soldering the solder reflow profile should be established by
accurately measuring the modules CP connector
temperatures.
REFLOW TEMP (°C)
REFLOW TIME (S)
Figure 35. Reflow Profile for Tin/Lead (Sn/Pb) process.
MAX TEMP SOLDER (°C)
Figure 36. Time Limit Curve Above 205oC for Tin/Lead
(Sn/Pb) process.
GE Energy
Data Sheet
12V Austin SuperLynx
TM
II: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
January 14, 2016
©2016
General Electric Company. All rights reserved. Page
20
Surface Mount Information (continued)
Lead Free Soldering
The –Z versions of the Austin SuperLynx II 12V SMT modules
are lead-free (Pb-free) and RoHS compliant and are both
forward and backward compatible in a Pb-free and a SnPb
soldering process. Failure to observe the instructions below
may result in the failure of or cause damage to the modules
and can adversely affect long-term reliability.
Pb-free Reflow Profile
Power Systems will comply with J-STD-020 Rev. C
(Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices) for both Pb-free solder
profiles and MSL classification procedures. This standard
provides a recommended forced-air-convection reflow
profile based on the volume and thickness of the package
(table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu
(SAC). The recommended linear reflow profile using
Sn/Ag/Cu solder is shown in Figure. 37.
MSL Rating
The Austin SuperLynx II 12V SMT modules have a MSL rating
of 3.
Storage and Handling
The recommended storage environment and handling
procedures for moisture-sensitive surface mount packages
is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping
and Use of Moisture/Reflow Sensitive Surface Mount
Devices). Moisture barrier bags (MBB) with desiccant are
required for MSL ratings of 2 or greater. These sealed
packages should not be broken until time of use. Once the
original package is broken, the floor life of the product at
conditions of ≤ 30°C and 60% relative humidity varies
according to the MSL rating (see J-STD-033A). The shelf life
for dry packed SMT packages will be a minimum of 12
months from the bag seal date, when stored at the following
conditions: < 40° C, < 90% relative humidity.
Post Solder Cleaning and Drying Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The result
of inadequate cleaning and drying can affect both the
reliability of a power module and the testability of the
finished circuit-board assembly. For guidance on
appropriate soldering, cleaning and drying procedures, refer
to Board Mounted Power Modules: Soldering and Cleaning
Application Note (AN04-001).
Per J-STD-020 Rev. C
0
50
100
150
200
250
300
Reflow Time (Seconds)
Ref low Temp (°C)
Heating Zone
1°C/Second
Peak Temp 260°C
* Min. Time Above 235°C
15 Seconds
*Time Above 217°C
60 Seconds
Cooling
Zone
Figure 37. Recommended linear reflow profile using
Sn/Ag/Cu solder.
GE
Data Sheet
12V Austin SuperLynxTMII: SMT Non-Isolated DC-DC Power Modules
8.3Vdc –14Vdc input; 0.75Vdc to 5.5Vdc output; 16A Output Current
Contact Us
For more information, call us at
USA/Canada:
+1 877 546 3243, or +1 972 244 9288
Asia-Pacific:
+86.021.54279977*808
Europe, Middle-East and Africa:
+49.89.878067-280
www.gecriticalpower.com
GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no
liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s)
or information.
January 14, 2016 ©2016 General Electric Company. All International rights reserved. Version 1.48
Ordering Information
Please contact your GE Sales Representative for pricing, availability and optional features.
Table 2. Device Codes
Device Code
Input
Voltage
Range
Output
Voltage
Output
Current
Efficiency
3.3V@ 16A
Connector
Type Comcodes
ATA016A0X3-SR 8.3 – 14Vdc 0.75 – 5.5Vdc 16 A 92.0% SMT 108988440
ATA016A0X3-SRZ 8.3 – 14Vdc
0.75 – 5.5Vdc
16 A 92.0% SMT CC109104527
ATA016A0X43-SR 8.3 – 14Vdc
0.75 – 5.5Vdc
16 A 92.0% SMT 108988457
ATA016A0X43-SRZ 8.3 – 14Vdc
0.75 – 5.5Vdc
16 A 92.0% SMT 108996690
-Z refers to RoHS-compliant versions.
