Features
ROHS-6 Compliant
Optional Digital Diagnostic Monitoring available
- AFCT-5710Z family: without DMI
- AFCT-5715Z family: with DMI
Per SFF-8472, diagnostic features on AFCT-5715Z
family enable Diagnostic Monitoring Interface for
optical transceivers with real-time monitoring of:
- Transmitted optical power
- Received optical power
- Laser bias current
- Temperature
- Supply voltage
Compliant to IEEE 802.3Z Gigabit Ethernet (1.25 GBd)
1000BASE-LX & Small Form Factor Pluggable (SFP)
Multi-Source Agreement (MSA)
Manufactured in an ISO 9001 compliant facility
Hot-pluggable
Temperature options
(Extended) -10°C to +85°C
(Industrial) -40°C to +85°C
+3.3 V dc power supply
1310 nm longwave laser
Eye safety certi ed:
- US 21 CFR(J)
- IEC 60825-1 (+All)
LC-Duplex ber connector compatible
Link Lengths at 1.25 GBd:
- 0.5 to 550 m - 50 μm MMF
- 0.5 to 550 m - 62.5 μm MMF
- 0.5 m to 10 km - SMF
Applications
Ethernet Switch
Enterprise Router
Broadband aggregation and wireless infrastructure
Metro Ethernet multi-service access & provisioning
platforms
Description
The AFCT-571xZ family of Small Form Factor Pluggable
(SFP) LC optical transceivers o ers a wide range of
design options, including optional DMI features (further
described later), two temperature ranges (extended or
industrial), and choice of standard or bail delatch. The
AFCT-5715Z family targets applications requiring DMI,
while the AFCT-5710Z family is streamlined for those
applications where DMI is not needed. Throughout this
datasheet, AFCT-571xZ will refer to the entire product
family encompassing this full range of product options.
Part Number Options
The AFCT-571xZ SFP family consists of the following
products:
Part Number DMI Temperature Latch Design
AFCT-5710LZ No Extended Standard
AFCT-5710PZ No Extended Bail
AFCT-5710ALZ No Industrial Standard
AFCT-5710APZ No Industrial Bail
AFCT-5715LZ Yes Extended Standard
AFCT-5715PZ Yes Extended Bail
AFCT-5715ALZ Yes Industrial Standard
AFCT-5715APZ Yes Industrial Bail
* Extended Temperature Range is -10 to 85 degrees C
Industrial Temperature Range is -40 to 85 degrees C
Related Products
AFBR-5705Z SFP family: 1.25GBd Ethernet
(1000BASE-SX) & 1.0625GBd Fiber Channel with DMI
AFBR-5701Z SFP family: 1.25GBd Ethernet
(1000BASE-SX) & 1.0625GBd Fiber Channel without
DMI
AFCT-5715Z SFP family: 1.25GBd Ethernet
(1000BASE-LX) with DMI
AFCT-5710Z SFP family: 1.25GBd Ethernet
(1000BASE-LX) without DMI
AFCT-5710Z and AFCT-5715Z
Families of Single-Mode Small Form Factor Pluggable (SFP)
Optical Transceivers with Optional DMI for Gigabit Ethernet (1.25 GBd)
Data Sheet
2
text
Photo-Detector
Amplification
&
Quantization
Laser
Laser Driver &
Safety Circuit
Electrical Interface
RD+ (Receive Data)
RD- (Receive Data)
Rx Loss Of Signal
MOD-DEF2 (SDA)
TX_DISABLE
TD+ (Transmit Data)
TD- (Transmit Data)
TX_FAULT
MOD-DEF0
MOD-DEF1 (SCL)
Receiver
Transmitter
Optical Interface
Light from Fiber
Light to Fiber
Controller & Memory
Figure 1. Transceiver Functional Diagram
Overview
The AFCT-571xZ family is compliant with both IEEE
802.3Z (1000BASE-LX) and the SFP Multi-Source
Agreement (MSA) speci cation. These transceivers
are intended for premise, public and access network-
ing applications. They are quali ed in accordance with
GR-468-CORE, and transmit data over single-mode
(SM)  ber for a link distance of 10 km, in excess of the
standard.
The AFCT-5715Z family of optical transceivers adds
digital diagnostic monitoring to standard SFP function-
ality, enabling fault isolation, components monitoring
and failure prediction capabilities.
General Features
The AFCT-571xZ is compliant to 1 GbE speci cations.
This includes speci cations for the signal coding, optical
ber and connector types, optical and electrical trans-
mitter characteristics, optical and electrical receiver
characteristics, jitter characteristics, and compliance
testing methodology for the aforementioned.
This transceiver is capable of implementing both Single
Mode (SM) and Multimode (MM) optical  ber applica-
tions in that order of precedence in the event of con-
icting speci cations. In addition, the SM link type
exceeds the 2 m to 5 km 1000BASE-LX speci cation by
achieving compliance over 2 m to 10 km. The MM link
type is expected to meet the 62.5 μm MMF speci cation
when used with an o set launch” ber.
SFP MSA Compliance
The product package is compliant with the SFP MSA with
the LC connector option. The SFP MSA includes speci ca-
tions for mechanical packaging and performance as well
as dc, ac and control signal timing and performance.
The power supply is 3.3 V dc.
The High Speed I/O (HSIO) signal interface is a Low
Voltage Di erential type. It is ac coupled and terminated
internally to the module. The internal termination is a
100 Ohm di erential load.
Installation
The AFCT-571xZ can be installed in or removed from
any MSA-compliant Pluggable Small Form Factor (SFP)
port regardless of whether the host equipment is
operating or not. The module is simply inserted, electri-
cal-interface  rst, under  nger-pressure. Controlled hot-
plugging is ensured by 3-stage pin sequencing at the
electrical interface. This printed circuit board card-edge
connector is depicted in Figure 2.
As the module is inserted,  rst contact is made by
the housing ground shield, discharging any poten-
tially component-damaging static electricity. Ground
pins engage next and are followed by Tx and Rx
power supplies. Finally, signal lines are connected. Pin
functions and sequencing are listed in Table 2.
3
Figure 3. Typical Application Con guration
VEET20
TD–
19
TD+
18
VEET17
VCCT16
VCCR15
VEER14
RD+
13
RD–
12
VEER11
TOP OF BOARD
VEET1
TX FAULT
2
TX DISABLE
3
MOD-DEF(2)4
MOD-DEF(1)
5
MOD-DEF(0)
6
RATE SELECT7
LOS
8
VEER9
VEER10
BOTTOM OF BOARD
(AS VIEWED THROUGH TOP OF BOARD)
ENGAGEMENT
SEQUENCE
3 2 1 3 2 1
Figure 2. Pin description of the SFP electrical interface.
Transmitter Section
The transmitter section includes a 1310 nm Fabry-Perot
laser and a transmitter driver circuit. The driver circuit
maintains a constant optical power level provided that
the data pattern is valid 8B/10B code. Connection to the
transmitter is provided via a LC optical connector.
The transmitter has full IEC 60825 and CDRH Class 1 eye
safety.
TX_DISABLE
The transmitter output can be disabled by asserting pin
3, TX_DISABLE. A high signal asserts this function while
a low signal allows normal laser operation. In addition,
via the 2-wire serial interface the transmitter output can
be disabled (address A2h, byte 110, bit 6) or monitored
(address A2h, byte 110, bit 7). The contents of A2h, byte
110, bit 6 are logic OR’d with hardware Tx_Disable (pin
3) to control transmitter operation. In the event of a
transceiver fault, such as the activation of the eye safety
circuit, toggling of the TX_DISABLE will reset the trans-
mitter, as depicted in Figure 4.
LASER DRIVER
& SAFETY
CIRCUITRY
50 Ω
50 Ω
SO+
SO–
AMPLIFICATION
&
QUANTIZATION
50 Ω
50 Ω
SI+
SI–
VREFR
VREFR
TBC
EWRAP
RBC
Rx_RATE
Rx_LOS
GPIO(X)
GPIO(X)
GP14
REFCLK
Tx_FAULT
TBC
EWRAP
RBC
Rx_RATE
REFCLK
TX[0:9]
RX[0:9]
Tx_FAULT
Tx_DISABLE
TD+
TD–
TX GND
MOD_DEF2
EEPROM
MOD_DEF1
MOD_DEF0
RX GND
4.7 K to 10 KΩ
3.3 V
4.7 K to
10 KΩ
3.3 V
4.7 K to
10 KΩ
4.7 K to
10 KΩ
106.25 MHz
PROTOCOL
IC
SFP MODULE
VCC,T
1 µH
1 µH
10 µF 0.1 µF
3.3 V
4.7 K to 10 KΩ
10 µF 0.1
µF
0.1 µF
4.7 K to 10 KΩ
RD+
RD–
Rx_LOS
0.01 µF
0.01 µF
100 Ω
0.01 µF
0.01 µF
V
CC
,R
100
Ω
50 Ω
V
CC
,R
50 Ω
V
CC
,R
4
Figure 4. MSA required power supply  lter
V
CC
T
0.1 µF
0.1 µF 10 µF
1 µH
1 µH
0.1 µF 10 µF
3.3 V
SFP MODULE
V
CC
R
HOST BOARD
Functional Data I/O
Avagos AFCT-571xZ transceiver is designed to accept
industry standard di erential signals. The transceiver
provides an AC-coupled, internally terminated data
interface. Bias resistors and coupling capacitors have
been included within the module to reduce the number
of components required on the customer’s board.
Figure 2 illustrates the recommended interface circuit.
Digital Diagnostic Interface and Serial Identi cation
The AFCT-571xZ family complies with the SFF-8074i
speci cation, which de nes the modules serial identi -
cation protocol to use the 2-wire serial CMOS EEPROM
protocol of the ATMEL AT24C01A or similar. Standard
SFP EEPROM bytes 0-255 are addressed per SFF-8074i at
memory address 0xA0 (A0h).
As an enhancement to the conventional SFP interface
de ned in SFF-8074i, the AFCT-5715Z is also compliant
to SFF-8472 (the digital diagnostic interface for SFP).
This enhancement adds digital diagnostic monitoring
to standard SFP functionality, enabling failure predic-
tion, fault isolation, and component monitoring capa-
bilities.
Using the 2-wire serial interface, the AFCT-5715Z
provides real time access to transceiver internal supply
voltage and temperature, transmitter output power,
laser bias current and receiver average input power,
allowing a host to predict system compliance issues.
These  ve parameters are internally calibrated, per the
MSA. New digital diagnostic information is accessed
per SFF-8472 using EEPROM bytes 0-255 at memory
address 0xA2 (A2h).
The digital diagnostic interface also adds the ability to
disable the transmitter (TX_DISABLE), monitor for Trans-
mitter Faults (TX_FAULT) and monitor for Receiver Loss
of Signal (RX_LOS).
Contents of the MSA-compliant serial ID memory are
shown in Tables 10 through 14. The SFF-8074i and
SFF-8472 speci cations are available from the SFF
Committee at http://www.s committee.org.
The I2C accessible memory page address 0xB0 is used
internally by SFP for the test and diagnostic purposes
and it is reserved.
Predictive Failure Identi cation
The diagnostic information allows the host system
to identify potential link problems. Once identi ed, a
fail-over technique can be used to isolate and replace
suspect devices before system uptime is impacted.
TX_FAULT
A laser fault or a low VCC condition will activate the
transmitter fault signal, TX_FAULT, and disable the laser.
This signal is an open collector output (pull-up required
on the host board); A low signal indicates normal laser
operation and a high signal indicates a fault. The TX_
FAULT will be latched high when a laser fault occurs and
is cleared by toggling the TX_DISABLE input or power
cycling the transceiver. The TX_FAULT is not latched
for Low VCC. The transmitter fault condition can also
be monitored via the two-wire serial interface (address
A2h, byte 110, bit 2).
Eye Safety Circuit
Under normal operating conditions, the laser power
will be maintained below the eye-safety limit. If the
eye safety limit is exceeded at any time, a laser fault will
occur and the TX_FAULT output will be activated.
Receiver Section
The receiver section for the AFCT-571xZ contains an
InGaAs/InP photo detector and a preampli er mounted
in an optical subassembly. This optical subassembly is
coupled to a post ampli er/decision circuit on a circuit
board. The design of the optical subassembly provides
better than 12 dB Optical Return Loss (ORL).
Connection to the receiver is provided via a LC optical
connector.
RX_LOS
The receiver section contains a loss of signal (RX_LOS)
circuit to indicate when the optical input signal power
is insu cient for Gigabit Ethernet compliance. A high
signal indicates loss of modulated signal, indicating link
failure such as a broken  ber or a failed transmitter. RX_
LOS can be also be monitored via the two-wire serial
(address A2h, byte 110, bit 1).
5
Table 1. Regulatory Compliance
Feature Test Method Performance
Electrostatic Discharge (ESD)
to the Electrical Pins
MIL-STD-883C Method 3015.4
JEDEC/EIA JESD22-A114-A
Class 2 (>2000 Volts)
Electrostatic Discharge (ESD)
to the Duplex LC Receptacle
Bellcore GR1089-CORE 25 kV Air Discharge
10 Zaps at 8 kV (contact discharge) on the electri-
cal faceplate on panel.
Electromagnetic Interference
(EMI)
FCC Class B Applications with high SFP port counts are ex-
pected to be compliant; however, margins are de-
pendent on customer board and chassis design.
Immunity Variation of IEC 61000-4-3 No measurable e ect from a 10 V/m  eld swept
from 80 to 1000 MHz applied to the transceiver
without a chassis enclosure.
Eye Safety US FDA CDRH AEL Class 1
EN (IEC) 60825-1, 2,
EN60950 Class 1
CDRH certi cation # 9521220-132
TUV  le R72102126.01
Component Recognition Underwriters Laboratories and
Canadian Standards Association Joint
Component Recognition for Informa-
tion Technology Equipment Including
Electrical Business Equipment
UL  le # E173874
ROHS Compliance Less than 1000ppm of: cadmium, lead, mercury,
hexavalent chromium, polybrominated biphenyls,
and polybrominated biphenyl ethers
Operating Temperature
The AFCT-571xZ family is available in either Extended
(-10 to +85°C) or Industrial (-40 to +85°C) temperature
ranges.
Power Supply Noise
The AFCT-571xZ can withstand an injection of PSN on
the VCC lines of 100 mV ac with a degradation in eye
mask margin of up to 10% on the transmitter and a 1
dB sensitivity penalty on the receiver. This occurs when
the product is used in conjunction with the MSA rec-
ommended power supply  lter shown in Figure 3.
Regulatory Compliance
The transceiver regulatory compliance is provided in
Table 1 as a  gure of merit to assist the designer. The
overall equipment design will determine the certi ca-
tion level.
Compliance Prediction
The real-time diagnostic parameters can be monitored
to alert the system when operating limits are exceeded
and compliance cannot be ensured.
Fault Isolation
The diagnostic information can allow the host to
pinpoint the location of a link problem and accelerate
system servicing and minimize downtime.
Component Monitoring
As part of the host system monitoring, the real time
diagnostic information can be combined with system
level monitoring to ensure system reliability.
Application Support
An Evaluation Kit and Reference Designs are available
to assist in evaluation of the AFCT-571xZ SFPs. Please
contact your local Field Sales representative for avail-
ability and ordering details.
6
Eye Safety
The AFCT-571xZ transceivers provide Class 1 eye
safety by design. Avago Technologies has tested the
transceiver design for regulatory compliance, under
normal operating conditions and under a single fault
condition. See Table 1.
Flammability
The AFCT-571xZ family of SFPs is compliant to UL
94V-0.
Customer Manufacturing Processes
This module is pluggable and is not designed for
aqueous wash, IR re ow, or wave soldering processes.
Caution
The AFCT-571xZ contains no user-serviceable parts.
Tampering with or modifying the performance of the
AFCT-571xZ will result in voided product warranty. It
may also result in improper operation of the transceiver
circuitry, and possible over-stress of the laser source.
Device degradation or product failure may result.
Connection of the AFCT-571xZ to a non-approved
optical source, operating above the recommended
absolute maximum conditions may be considered an
act of modifying or manufacturing a laser product. The
person(s) performing such an act is required by law to
re-certify and re-identify the laser product under the
provisions of U.S. 21 CF.
Electrostatic Discharge (ESD)
There are two conditions in which immunity to ESD
damage is important:
The  rst condition is static discharge to the transceiver
during handling such as when the transceiver is inserted
into the transceiver port. To protect the transceiver,
it is important to use normal ESD handling precau-
tions including the use of grounded wrist straps, work
benches, and  oor mats in ESD controlled areas. The ESD
sensitivity of the AFCT-571xZ is compatible with typical
industry production environments.
The second condition is static discharge to the exterior
of the host equipment chassis after installation. To the
extent that the duplex LC optical interface is exposed
to the outside of the host equipment chassis, it may be
subject to system-level ESD requirements. The ESD per-
formance of the AFCT-571xZ exceeds typical industry
standards. Table 1 documents ESD immunity to both of
these conditions.
Electromagnetic Interference (EMI)
Most equipment designs using the AFCT-571xZ SFPs
are subject to the requirements of the FCC in the
United States, CENELEC EN55022 (CISPR 22) in Europe
and VCCI in Japan. The metal housing and shielded
design of the transceiver minimize EMI and provide
excellent EMI performance.
EMI Immunity
The AFCT-571xZ transceivers have a shielded design
to provide excellent immunity to radio frequency
electromagnetic  elds which may be present in some
operating environments.
7
Table 2. Pin description
Pin Name Function/Description
Engagement
Order(insertion) Notes
1 VeeT Transmitter Ground 1
2 TX Fault Transmitter Fault Indication 3 1
3 TX Disable Transmitter Disable - Module disables on high or open 3 2
4 MOD-DEF2 Module De nition 2 - Two wire serial ID interface 3 3
5 MOD-DEF1 Module De nition 1 - Two wire serial ID interface 3 3
6 MOD-DEF0 Module De nition 0 - Grounded in module 3 3
7 Rate Selection Not Connected 3
8 LOS Loss of Signal 3 4
9 VeeR Receiver Ground 1
10 VeeR Receiver Ground 1
11 VeeR Receiver Ground 1
12 RD- Inverse Received Data Out 3 5
13 RD+ Received Data Out 3 5
14 VeeR Reciver Ground 1
15 VccR Receiver Power -3.3 V ±5% 2 6
16 VccT Transmitter Power -3.3 V ±5% 2 6
17 VeeT Transmitter Ground 1
18 TD+ Transmitter Data In 3 7
19 TD- Inverse Transmitter Data In 3 7
20 VeeT Transmitter Ground 1
Notes:
1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7KΩ – 10 KΩ resistor on the host board to a supply
<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the
output will be pulled to < 0.8 V.
2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 KΩ resistor.
Low (0 – 0.8 V): Transmitter on
Between (0.8 V and 2.0 V): Unde ned
High (2.0 – 3.465 V): Transmitter Disabled
Open: Transmitter Disabled
3. Mod-Def 0,1,2. These are the module de nition pins. They should be pulled up with a 4.7-10 KΩ resistor on the host board to a supply less
than VccT +0.3 V or VccR+0.3 V.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is clock line of two wire serial interface for optional serial ID
Mod-Def 2 is data line of two wire serial interface for optional serial ID
4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 KΩ – 10 KΩ resistor on the host board
to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as de ned
by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
5. RD-/+: These are the di erential receiver outputs. They are AC coupled 100 Ω di erential lines which should be terminated with 100 Ω
di erential at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on
these lines must be between 370 and 2000 mV di erential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv
di erential.
6. VccR and VccT are the receiver and transmitter power supplies. They are de ned as 3.135 – 3.465 V at the SFP connector pin. The in-rush
current will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.
7. TD-/+: These are the di erential transmitter inputs. They are AC coupled di erential lines with 100 Ω di erential termination inside the
module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept di erential swings of
500 – 2400 mV (250 – 1200 mV single ended). However, the applicable recommended di erential voltage swing is found in Table 5.
8
Table 3. Absolute Maximum Ratings
Absolute maximum ratings are those values beyond which functional performance is not intended, device reliabil-
ity is not implied, and damage to the device may occur.
Parameter Symbol Minimum Maximum Unit Notes
Storage Temperature (non-operating) TS-40 +100 ° C
Relative Humidity RH 5 95 %
Case Temperature TC-40 85 ° C
Supply Voltage VCC -0.5 3.8 V 1
Control Input Voltage VI-0.5 VCC+0.5 V
Table 4. Recommended Operating Conditions
Typical operating conditions are those values for which functional performance and device reliability is implied.
Parameter Symbol Minimum Typical Maximum Unit Notes
Case Operating Temperature
AFCT-5710LZ/PZ & AFCT-5715LZ/PZ
AFCT-5710ALZ/APZ & AFCT-5715ALZ/APZ
TC
TC
-10
-40
+85
+85
° C
° C
Supply Voltage VCC 3.14 3.3 3.47 V
Table 5. Transceiver Electrical Characteristics
Parameter Symbol Minimum Typical Maximum Unit Notes
Module supply current ICC 200 240 mA 2
Power Dissipation PDISS 660 830 mW 2
AC Electrical Characteristics
Power Supply Noise Rejection (peak - peak) PSNR 100 mV 3
Inrush Current 30 mA
DC Electrical Characteristics
Sense Outputs:
Transmit Fault (TX_FAULT)
Loss of Signal (LOS) MOD-DEF2
VOH 2.0 VccT, R+0.3 V 4
VOL 0.8 V
Control Inputs:
Transmitter Disable (TX_DISABLE)
MOD-DEF1, 2
VIH 2.0 Vcc V 4,5
VIL 0.8 V
Data Input:
Transmitter Di erential Input Voltage (TD+/-)
VI500 2400 mV 6
Data Ouput:
Receiver Di erential Output Voltage (RD+/-)
VO370 1600 mV 7
Receiver Data Rise and Fall Times Trf 400 ps
Receiver Contributed Total Jitter TJ 0.33267 UIps 8
Notes:
1 The module supply voltages, VccT and VccR, must not di er by more than 0.5V or damage to the device may occur.
2. Over temperature and Beginning of Life.
3. MSA lter is required on host board 10 Hz to 1 MHz. See Figure 3
4. LVTTL, External 4.7 - 10 KΩ Pull-Up Resistor required
5. LVTTL, Internal 4.7 - 10 KΩ Pull-Up Resistor required for TX_Disable
6. Internally ac coupled and terminated (100 Ohm di erential)
7. Internally ac coupled and load termination located at the user SerDes
8. Per IEEE 802.3
9
Table 6. Transmitter Optical Characteristics
Parameter Symbol Minimum Typical Maximum Unit Notes
Average Optical Output Power POUT -9.5 -3 dBm Note 1
Optical Extinction Ratio ER 9 dB
TX Optical Eye Mask Margin MM 0 30 % Note 3
Center Wavelength λC 1270 1355 nm
Spectral Width - rms σ, rms nm
Optical Rise/Fall Time tr, tf 260 ps 20-80%
Relative Intensity Noise RIN -120 dB/Hz
Contributed Total Jitter (Transmitter)
1.25 Gb/s
TJ 0.284
227
UI
ps
Note 2
POUT TX_DISABLE Asserted POFF -45 dBm
Notes:
1. Class 1 Laser Safety per FDA/CDRH
2. Contributed total jitter is calculated from DJ and RJ measurements using TJ = RJ + DJ. Contributed RJ is calculated for 1x10-12 BER by
multiplying the RMS jitter (measured on a single rise or fall edge) from the oscilloscope by 14. Per FC-PI (Table 9 - SM jitter output, note 1), the
actual contributed RJ is allowed to increase above its limit if the actual contributed DJ decreases below its limits, as long as the component
output DJ and TJ remain within their speci ed FC-PI maximum limits with the worst case speci ed component jitter input.
3. Eye shall be measured with respect to the mask of the eye using  lter de ned in IEEE 802.3 section 38.6.5
Table 7. Receiver Optical Characteristics
Parameter Symbol Minimum Typical Maximum Unit Notes
Input Optical Power PIN -3 dBm
Receiver Sensitivity PMIN -19 dBm 1, 2
Stressed Receiver Sensitivity
(Optical Average Input Power) -14.4 dBm
Receiver Electrical 3 dBUpper
Cuto Frequency 1500 MHz
Operating Center Wavelength ΛC1270 1355 nm
Return Loss (minimum) 12 dB
Loss of Signal - Assert PA-30 dBm 3
Loss of Signal - De-Assert PD-20 dBm 3
Loss of Signal - Hysteresis PD - PA0.5 dB
Notes:
1. BER = 10-12
2. An average power of -20 dBm with an Extinction Ratio of 9 dB is approximately equivalent to an OMA of 15 μW.
3. These average power values are speci ed with an Extinction Ratio of 9 dB. The loss-of-signal circuitry responds to valid 8B/10B-encoded peak
to peak input optical power, not average power.
10
Table 8. Transceiver Timing Characteristics
Parameter Symbol Minimum Maximum Unit Notes
Hardware TX_DISABLE Assert Time t_o 10 μs Note 1
Hardware TX_DISABLE Negate Time t_on 1 ms Note 2
Time to initialize, including reset of TX_FAULT t_init 300 ms Note 3
Hardware TX_FAULT Assert Time t_fault 100 μs Note 4
Hardware TX_DISABLE to Reset t_reset 10 μs Note 5
Hardware RX_LOS Assert Time t_loss_on 100 μs Note 6
Hardware RX_LOS De-Assert Time t_loss_o 100 μs Note 7
Software TX_DISABLE Assert Time t_o _soft 100 ms Note 8
Software TX_DISABLE Negate Time t_on_soft 100 ms Note 9
Software Tx_FAULT Assert Time t_fault_soft 100 ms Note 10
Software Rx_LOS Assert Time t_loss_on_soft 100 ms Note 11
Software Rx_LOS De-Assert Time t_loss_o _soft 100 ms Note 12
Analog parameter data ready t_data 1000 ms Note 13
Serial bus hardware ready t_serial 300 ms Note 14
Write Cycle Time t_write 10 ms Note 15
Serial ID Clock Rate f_serial_clock 400 kHz
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured
from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of
nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.
Table 9. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
Parameter Symbol Min Units Notes
Transceiver Internal Temperature Accuracy TINT ± 3.0 °C Valid from TC = -40 °C to +85 °C
Transceiver Internal Supply Voltage Accuracy VINT ± 0.1 V Valid over VCC = 3.3 V ± 5%
Transmitter Laser DC Bias Current Accuracy IINT ± 10 % Percentage of nominal bias value
Transmitted Average Optical Output Power Accuracy PT± 3.0 dB Valid from 100 μW to 500μW, avg
Received Average Optical Input Power Accuracy PR± 3.0 dB Valid from 10 μW to 500μW avg
11
Tx_FAULT
VCC > 2.97 V
t_init
Tx_DISABLE
TRANSMITTED SIGNAL
t_init
Tx_FAULT
VCC > 2.97 V
Tx_DISABLE
TRANSMITTED SIGNAL
t-init: TX DISABLE NEGATED t-init: TX DISABLE ASSERTED
Tx_FAULT
VCC > 2.97 V
t_init
Tx_DISABLE
TRANSMITTED SIGNAL
t_off
Tx_FAULT
Tx_DISABLE
TRANSMITTED SIGNAL
t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED t-off & t-on: TX DISABLE ASSERTED THEN NEGATED
INSERTION
t_on
Tx_FAULT
OCCURANCE OF FAULT
t_fault
Tx_DISABLE
TRANSMITTED SIGNAL
Tx_FAULT
OCCURANCE OF FAULT
Tx_DISABLE
TRANSMITTED SIGNAL
t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
t_reset t_init*
* CANNOT READ INPUT...
Tx_FAULT
OCCURANCE OF FAULT
t_fault
Tx_DISABLE
TRANSMITTED SIGNAL
OPTICAL SIGNAL
LOS
t-fault: TX DISABLE ASSERTED THEN NEGATED,
TX SIGNAL NOT RECOVERED
t-loss-on & t-loss-off
t_loss_on
t_init*
t_reset
* SFP SHALL CLEAR Tx_FAULT IN
t_init IF THE FAILURE IS TRANSIENT
t_loss_off
OCCURANCE
OF LOSS
Figure 5. Transceiver Timing Diagrams (Module Installed Except Where Noted)
12
Table 10. EEPROM Serial ID Memory Contents - Page A0h
Byte #
Decimal
Data
Hex Notes
Byte #
Decimal
Data
Hex Notes
0 03 SFP physical device 37 00 Hex Byte of Vendor OUI (note 3)
1 04 SFP function de ned by serial ID only 38 17 Hex Byte of Vendor OUI (note 3)
2 07 LC optical connector 39 6A Hex Byte of Vendor OUI (note 3)
3 00 40 41 A” - Vendor Part Number ASCII character
4 00 41 46 “F” - Vendor Part Number ASCII character
5 00 42 43 “C” - Vendor Part Number ASCII character
6 02 1000BASE-LX 43 54 T - Vendor Part Number ASCII character
7 00 44 2D “-” - Vendor Part Number ASCII character
8 00 45 35 “5” - Vendor Part Number ASCII character
9 00 46 37 “7” - Vendor Part Number ASCII character
10 00 47 31 “1” - Vendor Part Number ASCII character
11 01 Compatible with 8B/10B encoded data 48 Note 4
12 0C 1200 MBit/sec nominal bit rate 49 Note 4
13 00 50 Note 4
14 0A 51 Note 4
15 64 52 20 “ - Vendor Part Number ASCII character
16 37 Note 1 53 20 “ - Vendor Part Number ASCII character
17 37 Note 2 54 20 “ - Vendor Part Number ASCII character
18 00 55 20 “ - Vendor Part Number ASCII character
19 00 56 20 “ - Vendor Revision Number ASCII character
20 41 A - Vendor Name ASCII character 57 20 “ - Vendor Revision Number ASCII character
21 56 V - Vendor Name ASCII character 58 20 “ - Vendor Revision Number ASCII character
22 41 A - Vendor Name ASCII character 59 20 “ - Vendor Revision Number ASCII character
23 47 “G” - Vendor Name ASCII character 60 05 Hex Byte of Laser Wavelength (Note 5)
24 4F “O” - Vendor Name ASCII character 61 1E Hex Byte of Laser Wavelength (Note 5)
25 20 “ - Vendor Name ASCII character 62 00
26 20 “ - Vendor Name ASCII character 63 Checksum for Bytes 0-62 (Note 6)
27 20 “ - Vendor Name ASCII character 64 00
28 20 “ - Vendor Name ASCII character 65 1A Hardware SFP TX_DISABLE, TX_FAULT & RX_LOS
29 20 “ - Vendor Name ASCII character 66 00
30 20 “ - Vendor Name ASCII character 67 00
31 20 “ - Vendor Name ASCII character 68-83 Vendor Serial Number ASCII characters (Note7)
32 20 “ - Vendor Name ASCII character 84-91 Vendor Date Code ASCII characters (Note 8)
33 20 “ - Vendor Name ASCII character 92 Note 4
34 20 “ - Vendor Name ASCII character 93 Note 4
35 20 “ - Vendor Name ASCII character 94 Note 4
36 00 95 Checksum for Bytes 64-94 (Note 6)
96 - 255 00
Notes:
1. Link distance with 50/125 μm cable.
2. Link distance with 62.5/125 μm.
3. The IEEE Organizationally Unique Identi er (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes hex).
4. See Table 11 on following page for part number extensions and data- elds.
5. Laser wavelength is represented in 16 unsigned bits. The hex representation of 1310 (nm) is 051E.
6. Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment.
7. Addresses 68-83 specify the ASCII serial number and will vary on a per unit basis.
8. Addresses 84-91 specify the ASCII date code and will vary on a per date code basis.
13
Table 11. Part Number Extensions and Data elds
AFCT-5710ALZ AFCT-5710APZ AFCT-5710LZ AFCT-5710PZ
Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII
48 30 0 48 30 0 48 30 0 48 30 0
49 41 A 49 41 A 49 4C L 49 50 P
50 4C L 50 50 P 50 5A Z 50 5A Z
51 5A Z 51 5A Z 51 20 51 20
92 0 92 0 92 0 92 0
93 0 93 0 93 0 93 0
94 0 94 0 94 0 94 0
AFCT-5715ALZ AFCT-5715APZ AFCT-5715LZ AFCT-5715PZ
Address Hex ASCII Address Hex ASCII Address Hex ASCII Address Hex ASCII
48 35 5 48 35 5 48 35 5 48 35 5
49 41 A 49 41 A 49 4C L 49 50 P
50 4C L 50 50 P 50 5A Z 50 5A Z
51 5A Z 51 5A Z 51 20 51 20
92 68 92 68 92 68 92 68
93 F0 93 F0 93 F0 93 F0
94 1 94 1 94 1 94 1
14
Table 12. EEPROM Serial ID Memory Contents - Address A2h (AFCT-5715Z family only)
Byte #
Decimal Notes
Byte #
Decimal Notes
Byte #
Decimal Notes
0 Temp H Alarm MSB126 Tx Pwr L Alarm MSB4104 Real Time Rx PAV MSB5
1 Temp H Alarm LSB127 Tx Pwr L Alarm LSB4105 Real Time Rx PAV LSB5
2 Temp L Alarm MSB128 Tx Pwr H Warning MSB4106 Reserved
3 Temp L Alarm LSB129 Tx Pwr H Warning LSB4107 Reserved
4 Temp H Warning MSB130 Tx Pwr L Warning MSB4108 Reserved
5 Temp H Warning LSB131 Tx Pwr L Warning LSB4109 Reserved
6 Temp L Warning MSB132 Rx Pwr H Alarm MSB5110 Status/Control - see Table 13
7 Temp L Warning LSB133 Rx Pwr H Alarm LSB5111 Reserved
8V
CC H Alarm MSB234 Rx Pwr L Alarm MSB5112 Flag Bits - see Table 14
9V
CC H Alarm LSB235 Rx Pwr L Alarm LSB5113 Flag Bit - see Table 14
10 VCC L Alarm MSB236 Rx Pwr H Warning MSB5114 Reserved
11 VCC L Alarm LSB237 Rx Pwr H Warning LSB5115 Reserved
12 VCC H Warning MSB238 Rx Pwr L Warning MSB5116 Flag Bits - see Table 14
13 VCC H Warning LSB239 Rx Pwr L Warning LSB5117 Flag Bits - see Table 14
14 VCC L Warning MSB240-55 Reserved 118 Reserved
15 VCC L Warning LSB256-94 External Calibration Constants6119 Reserved
16 Tx Bias H Alarm MSB395 Checksum for Bytes 0-947120-122 Reserved
17 Tx Bias H Alarm LSB396 Real Time Temperature MSB1123
18 Tx Bias L Alarm MSB397 Real Time Temperature LSB1124
19 Tx Bias L Alarm LSB398 Real Time Vcc MSB2125
20 Tx Bias H Warning MSB399 Real Time Vcc LSB2126
21 Tx Bias H Warning LSB3100 Real Time Tx Bias MSB3127 Reserved8
22 Tx Bias L Warning MSB3101 Real Time Tx Bias LSB3128-247 Customer Writable9
23 Tx Bias L Warning LSB3102 Real Time Tx Power MSB4248-255 Vendor Speci c
24 Tx Pwr H Alarm MSB4103 Real Time Tx Power LSB4
25 Tx Pwr H Alarm LSB4
Notes:
1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256 °C.
2. Supply voltage (VCC) is decoded as a 16 bit unsigned integer in increments of 100 μV.
3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 μA.
4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW.
5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 μW.
6. Bytes 55-94 are not intended from use with AFCT-5715xxxx, but have been set to default values per SFF-8472.
7. Bytes 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment.
8. Byte 127 accepts a write but performs no action (reserved legacy byte).
9. Bytes 128-247 are write enabled (customer writable).
15
Table 13. EEPROM Serial ID Memory Contents - Address A2h, Byte 110 (AFCT-5715Z family only)
Bit # Status/Control Name Description
7 Tx Disable State Digital state of SFP Tx Disable Input Pin (1 = Tx_ Disable asserted)
6 Soft Tx Disable Read/write bit for changing digital state of SFP Tx_Disable function1
5 Reserved
4 Rx Rate Select State Digital state of SFP Rate Select Input Pin (1 = full bandwidth of 155 Mbit)2
3 Reserved
2 Tx Fault State Digital state of the SFP Tx Fault Output Pin (1 = Tx Fault asserted)
1 Rx LOS State Digital state of the SFP LOS Output Pin (1 = LOS asserted)
0 Data Ready (Bar) Indicates transceiver is powered and real time sense data is ready (0 = Ready)
Notes:
1. Bit 6 is logic OR’d with the SFP Tx_Disable input pin 3 ... either asserted will disable the SFP transmitter.
2. AFCT-5715Z does not respond to state changes on Rate Select Input Pin. It is internally hardwired to full bandwidth.
Table 14. EEPROM Serial ID Memory Contents - Address A2h, Bytes 112, 113, 116, 117
(AFCT-5715Z family only)
Byte Bit # Flag Bit Name Description
112
7 Temp High Alarm Set when transceiver nternal temperature exceeds high alarm threshold.
6 Temp Low Alarm Set when transceiver internal temperature exceeds alarm threshold.
5V
CC High Alarm Set when transceiver internal supply voltage exceeds high alarm threshold.
4V
CC Low Alarm Set when transceiver internal supply voltage exceeds low alarm threshold.
3 Tx Bias High Alarm Set when transceiver laser bias current exceeds high alarm threshold.
2 Tx Bias Low Alarm Set when transceiver laser bias current exceeds low alarm threshold.
1 Tx Power High Alarm Set when transmitted average optical power exceeds high alarm threshold.
0 Tx Power Low Alarm Set when transmitted average optical power exceeds low alarm threshold.
113
7 Rx Power High Alarm Set when received P_Avg optical power exceeds high alarm threshold.
6 Rx Power Low Alarm Set when received P_Avg optical power exceeds low alarm threshold.
0-5 Reserved
116
7 Temp High Warning Set when transceiver internal temperature exceeds high warning threshold.
6 Temp Low Warning Set when transceiver internal temperature exceeds low warning threshold.
5V
CC High Warning Set when transceiver internal supply voltage exceeds high warning threshold.
4V
CC Low Warning Set when transceiver internal supply voltage exceeds low warning threshold.
3 Tx Bias High Warning Set when transceiver laser bias current exceeds high warning threshold.
2 Tx Bias Low Warning Set when transceiver laser bias current exceeds low warning threshold.
1 Tx Power High Warning Set when transmitted average optical power exceeds high warning threshold.
0 Tx Power Low Warning Set when transmitted average optical power exceeds low warning threshold.
117
7 Rx Power High Warning Set when received P_Avg optical power exceeds high warning threshold.
9 Rx Power Low Warning Set when received P_Avg optical power exceeds low warning threshold.
0-5 Reserved
16
[0.541±0.004]
13.8±0.1
[0.10]
2.60
[2.17±0.01]
55.2±0.2
[0.528±0.004]
13.4±0.1
AFCT-571xZ
1300 nm LASER PROD
21CFR(J) CLASS 1
COUNTRY OF ORIGIN YYWW
XXXXXX
DEVICE SHOWN WITH
DUST CAP AND BAIL
WIRE DELATCH
[0.246±0.002]
6.25±0.05
TX RX
DIMENSIONS ARE IN MILLIMETERS (INCHES)
[0.335±0.004]
8.5±0.1
FRONT EDGE OF SFP
TRANSCEIVER CAGE
[0.028]
0.7MAX. UNCOMPRESSED
[0.512±0.008]
13.0±0.2
ST ANDARD DELATCH
[0.261]
6.6
[0.53]
13.50
AREA
FOR
PROCESS
PLUG
[0.583]
14.8 MAX. UNCOMPRESSED
[0.48±0.01]
12.1±0.2
Figure 6. Drawing of SFP Transceiver
17
2x 1.7
20x 0.5 ± 0.03
0.9
2 ± 0.005 TYP.
0.06 L A S B S
10.53 11.93
20
10 11
PIN 1
20
10 11
PIN 1
0.8
TYP.
10.93
9.6
2x 1.55 ± 0.05
3.2 5
LEGEND
1. PADS AND VIAS ARE CHASSIS GROUND
2. THROUGH HOLES, PLATING OPTIONAL
3. HATCHED AREA DENO TES COMPONENT
AND TRACE KEEPOUT (EXCEPT
CHASSIS GROUND)
4. AREA DENOTES COMPONENT
KEEPOUT (TRA CES ALLO WED)
DIMENSIONS ARE IN MILLIMETERS
4
32
1
1
26.8 5
11x 2.0
10
3x
41.3
42.3
B
10x
1.05 ± 0.01
16.25
REF. 14.25
11.08
8.58
5.68
2.0
11x
11.93
9.6
4.8
8.48
A
3.68
SEE DET AIL 1
9x 0.95 ± 0.05
2.5
7.17.2
2.5
10
3x
34.5
16.25
MIN. PITCH
YX
DETAIL 1
0.85 ± 0.05
PCB
EDGE
0.06 L A S B S
0.1 L A S B S
0.1 L X A S
0.1 L X A S
0.1 S X Y
Figure 7. SFP host board mechanical layout
18
DIMENSIONS ARE IN MILLIMETERS [INCHES].
[.60±0.004]
15.25±0.1
[.64±0.004]
16.25±0.1MIN PITCH
[.41±0.004]
10.4±0.1
[.39]
TO PCB
10REF
[.02±0.004]
BELOW PCB
0.4±0.1
[.39]
9.8MAX
[.49]
12.4REF
[.05]
BELOW PCB
1.15REF
[1.64±.02]
41.73±0.5
[.14±.01]
3.5±0.3 [.07±.04]
1.7±0.9
[.59]
15MAX
AREA
FOR
PROCESS
PLUG
Tcase REFERENCE POINT
PCB
MSA-SPECIFIED BEZEL
BEZEL
CAGE
ASSEMBLY
Figure 8. Assembly Drawing
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes AV01-0167EN
AV02-2366EN - September 12, 2012
Ordering Information
Please contact your local  eld sales engineer or one of
Avago Technologies franchised distributors for ordering
information. For technical information, please visit
Avago Technologies’ web-page at www.avagotech.com or
contact one of Avago Technologies’ regional Technical
Response Centers.
For information related to SFF Committee documenta-
tion visit www.s committee.org.