1
2
notice_e-01
Notice for TAIYO YUDEN products 
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called TAIYO YUDENs official sales channel).
It is only applicable to the products purchased from any of TAIYO YUDEN s ofcial sales channel.
Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
Caution for export
Certain items in this catalog may require specific procedures for export according to Foreign Exchange and For-
eign Trade Control Law of Japan, U.S. Export Administration Regulations, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
112
1
2
leaded_i02_e-01
FEATURES
ORDERING CODE
EXTERNAL DIMENSIONS/STANDARD QUANTITY
APPLICATIONS
OPERATING TEMP.
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
The LHL08~LHL16 series radial inductors are encapsulated in a resin
housing which adds to the stability of the mounted part on a printed
circuit board.
The LHL08/LHL10/LHL13/LHL16 series are for high current applica-
tions.
The LHLP10/LHLP12/LHLP16 series are shielded type for high current ap-
plications.
LHLP10 series is also available in packaging.
LHLC08/LHLC10 series which are encapsulated in a resin housing, are ra-
dial leaded inductor for high current applications.
Ideal for use as a power choke coil in general household appliances
(TVS, PDPTV, LCDTV, DVD, etc) and industrial equipment.
Can also be used as a peaking coil in filtering applications.
For DC/DC converter (LCD TV, PDP TV, CTV, DVD etc.) (LHLC Series)
RADIAL LEADED INDUCTORS
Type Fig. D H2FφdStandard Quantity (pcs)
Box Bulk Taped
LHL08 9.0 max. 9.5 max. 5.0±1.0 5.0±1.0 0.6±0.05 100 1000
0.354 max. 0.374 max. 0.197±0.039 0.197±0.039 0.024±0.002
LHL10 11.0 max. 14.0 max. 5.0±1.0 5.0±1.0 0.6±0.05 50 500
0.433 max. 0.551 max. 0.197±0.039 0.197±0.039 0.024±0.002
LHL13 14.0 max. 17.0 max. 5.0±1.0 7.5±1.0 0.8±0.05 25 500
0.551 max. 0.669 max. 0.197±0.039 0.295±0.039 0.031±0.002
LHL16 17.0 max. 21.0 max. 5.0±1.0 7.5±1.0 0.8±0.05 500 250
0.669 max. 0.827 max. 0.197±0.039 0.295±0.039 0.031±0.002
LHLP10 11.0 max. 11.0 max. 5.0±1.0 5.0±1.0 0.6±0.05 500 200
0.433 max. 0.433 max. 0.197±0.039 0.197±0.039 0.024±0.004
LHLP12 13.0 max. 16.0 max. 5.0±1.0 5.0±1.0 0.6±0.05 300
0.512 max. 0.624 max. 0.197±0.039 0.197±0.039 0.024±0.004
LHLP16 17.0 max. 19.0 max. 5.0±1.0 7.5±1.0 0.8±0.05 200
0.669 max. 0.741 max. 0.197±0.039 0.295±0.039 0.031±0.004
Unitmm inch
Type
LH Radial leaded inductor
Packaging Code
NB Bulk (LHL)
TB
Ammo packaging (LHL)
Nominal Inductance
(μH)
example
1R0 1.0
150 15
102 1000
R=Decimal point
Inductance
Tolerances ()
J±5
K±10
M±20
N±30
Internal code
△△△ Standard product
Blank space
External
dimensions
mm max
08 9.0
10 11.0
12 13.0
13 14.0
16 17.0
Configuration
LStandard type Taping available
LP Shielded type Bulk
LC High current type
Blank space
L H L0 8 T B 1 0 1 K ○○○
❷❸❹ ❺❻❼
WAV E
25105Including self-generated heat
Type Fig. D H2FφdStandard Quantity (pcs)
Bulk Taped
LHLC08 9.0max
0.354max
9.5max
0.374max
5.0±1.0
0.197±0.039
5.0±1.0
0.197±0.039
0.6±0.05
0.024±0.002100 1000
LHLC10 11.0max
0.433max
14.0max
0.551max
5.0±1.0
0.197±0.039
5.0±1.0
0.197±0.039
0.6±0.05
0.024±0.00250 500
Unitmminch
LH type
113
1
2
leaded_i02_e-01
INDUCTORS
LEADED INDUCTORS
AVAILABLE INDUCTANCE RANGE
PART NUMBERS
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Range Type LHL08 LHL10 LHL13 LHL16 LHLP10 LHLP12 LHLP16
0.22μ
1.0μ1.0μ
10μ
3.3μ
10μ10μ10μ
100μ
47μ15μ
1.0m
10m
1.0m 1.0m 1.0m
100m
33m 10m 10m
150m
Inductance H
LHL08
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
min.
Self-resonant
frequency
MHz (min.)
DC Resistance
[Ω] (max.)
Rated current
A (max.)
Measuring
frequency
MHz
LHL081R0N RoHS 1.0 ±30
40
76 0.013 4.7
7.96
LHL081R5M RoHS 1.5
±20
65 0.014 4.4
LHL082R 2M RoHS 2.2 56 0.017 4.1
LHL082R7M RoHS 2.7 48 0.019 3.5
LHL083R3M RoHS 3.3 41 0.021 3.2
LHL083R9M RoHS 3.9 33 0.024 3.1
LHL084R7M RoHS 4.7 30 0.025 3.0
LHL085R6M RoHS 5.6 23 0.028 2.9
LHL086R8M RoHS 6.8 21 0.030 2.8
LHL088R2M RoHS 8.2 19 0.034 2.5
LHL08100K RoHS 10
±10
65 17 0.041 2.4
2.52
LHL08120K RoHS 12 16 0.044 2.3
LHL08150K RoHS 15
50
13 0.053 2.0
LHL08180K RoHS 18 12 0.060 1.9
LHL08220K RoHS 22 11 0.068 1.8
LHL08270K RoHS 27 10 0.091 1.5
LHL08330K RoHS 33
40
8.8 0.10 1.4
LHL08390K RoHS 39 8.4 0.12 1.3
LHL08470K RoHS 47 8.2 0.15 1.2
LHL08560K RoHS 56 7.9 0.17 1.1
LHL08680 K RoHS 68 35 7.0 0.20 1.0
LHL08820K RoHS 82 6.5 0.22 0.90
LHL08101K RoHS 100 25 5.7 0.32 0.79
0.796
LHL08121K RoHS 120 5.2 0.36 0.70
LHL08151K RoHS 150 20 4.7 0.41 0.64
LHL08181K RoHS 180 35 4.2 0.66 0.60
LHL08221K RoHS 220 3.7 0.73 0.53
LHL08271K RoHS 270 25 3.5 0.85 0.51
LHL08331K RoHS 330 3.2 0.97 0.44
LHL08391K RoHS 390 20 2.9 1.1 0.41
LHL08471K RoHS 470
25
2.4 1.3 0.38
LHL08561K RoHS 560 2.2 1.5 0.35
LHL08681K RoHS 680 2.0 1.8 0.32
LHL08821K RoHS 820 30 1.6 2.3 0.30
LHL08102J RoHS 1000
±5
55 1.5 2.7 0.25
0.252
LHL08122J RoHS 1200 45 1.4 3.2 0.22
LHL08152J RoHS 1500
55
1.3 4.1 0.20
LHL08182J RoHS 1800 1.2 4.8 0.19
LHL08222J RoHS 2200 1.1 5.6 0.16
LHL08272J RoHS 2700 1.0 7.5 0.15
LHL08332J RoHS 3300 0.85 8.5 0.14
LHL08392J RoHS 3900 0.78 9.7 0.11
LHL08472J RoHS 4700
65
0.68 14 0.10
LHL08562J RoHS 5600 0.62 16 0.093
LHL08682J RoHS 6800 0.61 18 0.092
LHL08822J RoHS 8200 0.60 20 0.084
LHL08103J RoHS 10000
60
0.48 32 0.070
L:1kHz
Q:0.0796
LHL08123J RoHS 12000 0.44 36 0.064
LHL08153J RoHS 15000 0.35 62 0.051
LHL08183J RoHS 18000 0.30 72 0.048
LHL08223J RoHS 22000 0.28 82 0.044
LHL08273J RoHS 27000 0.25 90 0.042
LHL08333J RoHS 33000 0.23 100 0.040
Please specify the packaging code. (TB: Taping, NB: Bulk)
Range Type LHLC08 LHLC10
0.1μRdc
max[Ω]
Imax[A] Rdc
max[Ω]
Imax[A]
1.0μ0.013 1.0μ5.4
10μ0.041 2.9 0.034
3.3μ
3.6
100μ0.32 1.0 0.18 1.5
1.0m 2.7 0.35 1.8 0.48
10m 32.0 0.11 19.0 0.14
100m
33m
240.0 0.038
150m
Inductance H
114
1
2
leaded_i02_e-01
PART NUMBERS
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
LHL10
Ordering code
EHS
(
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
min.
Self-resonant
frequency
MHz (min.)
DC Resistance
[Ω] (max.)
Rated current
A (max.)
Measuring
frequency
MHz
LHL103R3M RoHS 3.3
±2050
46 0.019 4.2
7.96
LHL103R9M RoHS 3.9 40 0.022 4.1
LHL104R7M RoHS 4.7 38 0.024 4.0
LHL105R6M RoHS 5.6 34 0.025 3.8
LHL106R8M RoHS 6.8 30 0.028 3.4
LHL108R2M RoHS 8.2 24 0.031 3.3
LHL10100K RoHS 10
±10
90
19 0.034 3.2
2.52
LHL10120K RoHS 12 16 0.038 2.8
LHL10150K RoHS 15 12 0.042 2.6
LHL10180K RoHS 18 9.2 0.046 2.4
LHL10220K RoHS 22
60
8.6 0.061 2.1
LHL10270K RoHS 27 7.1 0.069 2.0
LHL10330K RoHS 33 6.8 0.078 1.9
LHL10390K RoHS 39 6.7 0.085 1.8
LHL10470K RoHS 47 50 6.2 0.093 1.7
LHL10560K RoHS 56 5.2 0.10 1.6
LHL10680K RoHS 68 40 4.9 0.12 1.5
LHL10820K RoHS 82 4.7 0.13 1.4
LHL103R3M RoHS 3.3
±2050
46 0.019 4.2
7.96
LHL103R9M RoHS 3.9 40 0.022 4.1
LHL104R7M RoHS 4.7 38 0.024 4.0
LHL105R6M RoHS 5.6 34 0.025 3.8
LHL106R8M RoHS 6.8 30 0.028 3.4
LHL108R2M RoHS 8.2 24 0.031 3.3
LHL10100K RoHS 10
±10
90
19 0.034 3.2
2.52
LHL10120K RoHS 12 16 0.038 2.8
LHL10150K RoHS 15 12 0.042 2.6
LHL10180K RoHS 18 9.2 0.046 2.4
LHL10220K RoHS 22
60
8.6 0.061 2.1
LHL10270K RoHS 27 7.1 0.069 2.0
LHL10330K RoHS 33 6.8 0.078 1.9
LHL10390K RoHS 39 6.7 0.085 1.8
LHL10470K RoHS 47 50 6.2 0.093 1.7
LHL10560K RoHS 56 5.2 0.10 1.6
LHL10680K RoHS 68 40 4.9 0.12 1.5
LHL10820K RoHS 82 4.7 0.13 1.4
LHL10101K RoHS 100
±10
40
3.8 0.18 1.2
0.796
LHL10121K RoHS 120 3.2 0.25 1.0
LHL10151K RoHS 150 2.9 0.29 0.95
LHL10181K RoHS 180 2.6 0.40 0.80
LHL10221K RoHS 220 2.3 0.44 0.75
LHL10271K RoHS 270
30
2.1 0.50 0.70
LHL10331K RoHS 330 2.0 0.56 0.68
LHL10391K RoHS 390 1.8 0.62 0.63
LHL10471K RoHS 470 1.7 0.84 0.57
LHL10561K RoHS 560 1.5 0.93 0.52
LHL10681K RoHS 680 1.4 1.0 0.48
LHL10821K RoHS 820 1.3 1.4 0.42
LHL10102J RoHS 1000
±5
50
1.2 1.8 0.41
0.252
LHL10122J RoHS 1200 0.87 2.3 0.33
LHL10152J RoHS 1500 0.83 2.7 0.30
LHL10182J RoHS 1800 0.75 3.0 0.29
LHL10222J RoHS 2200 0.70 3.9 0.25
LHL10272J RoHS 2700 0.67 4.3 0.24
LHL10332J RoHS 3300 0.56 5.8 0.21
LHL10392J RoHS 3900 0.54 6.4 0.20
LHL10472J RoHS 4700 0.49 7.1 0.19
LHL10562J RoHS 5600 0.41 9.0 0.17
LHL10682J RoHS 6800 0.38 10 0.16
LHL10822J RoHS 8200 0.36 12 0.15
LHL10103J RoHS 10000
60
0.29 19 0.12
L:1kHz
Q:0.0796
LHL10123J RoHS 12000 0.27 21 0.11
LHL10153J RoHS 15000 0.24 34 0.090
LHL10183J RoHS 18000 0.21 38 0.081
LHL10223J RoHS 22000 0.20 43 0.075
LHL10273J RoHS 27000
40
0.15 67 0.060
LHL10333J RoHS 33000 0.14 76 0.056
LHL10393J RoHS 39000 0.13 84 0.053
LHL10473J RoHS 47000 0.12 96 0.050
LHL10563 J RoHS 56000
30
0.10 170 0.036
LHL10683J RoHS 68000 0.095 200 0.035
LHL10823J RoHS 82000 0.088 210 0.033
LHL10104 J RoHS 100000 0.085 240 0.031 L:1kHz
Q:0.0252
LHL10124 J RoHS 120000 0.070 260 0.030
LHL10154J RoHS 150000 0.069 300 0.028
Please specify the packaging code. (TB: Taping, NB: Bulk)
115
1
2
leaded_i02_e-01
INDUCTORS
LEADED INDUCTORS
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
PART NUMBERS
LHL16
LHLP10
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
min.
Self-resonant
frequency
MHz (min.)
DC Resistance
[Ω] (max.)
Rated current
A (max.)
Measuring
frequency
MHz
LHL16470K RoHS 47
±10
70 4.5 0.046 3.7 2.52
LHL16680K RoHS 68 3.9 0.054 3.3
LHL16101K RoHS 100
60
2.7 0.077 2.9
0.796
LHL16151K RoHS 150 2.3 0.11 2.4
LHL16221K RoHS 220 1.9 0.15 2.0
LHL16331K RoHS 330 40 1.6 0.21 1.5
LHL16471K RoHS 470 30 1.4 0.28 1.3
LHL16681K RoHS 680
20
1.2 0.35 1.1
LHL16102J RoHS 1000
±5
0.84 0.74 0.86
0.252
LHL16152J RoHS 1500 0.69 0.93 0.75
LHL16222J RoHS 2200 0.56 1.4 0.60
LHL16332J RoHS 3300 0.49 2.2 0.50
LHL16472J RoHS 4700 0.41 2.6 0.40
LHL16682J RoHS 6800 0.35 3.9 0.33
LHL16103J RoHS 10000 70 0.26 7.3 0.25 L:1KHz
Q:0.0796MHz
Please specify the packaging code. (TB: Taping, NB: Bulk)
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Nominal Inductance
[μH]
L Measuring
frequency
Inductance
Tolerance
DC Resistance
[Ω] (max.)
Rated current
A (max.)
LHLP10100M RoHS 10
2.52 ±20
0.038 2.5
LHLP10150M RoHS 15 0.049 2.2
LHLP10220M RoHS 22 0.075 1.9
LHLP10330M RoHS 33 0.094 1.7
LHLP10470M RoHS 47 0.15 1.3
LHLP10680 M RoHS 68 0.23 1.0
LHLP10101K RoHS 100
0.796 ±10
0.30 0.90
LHLP10151K RoHS 150 0.47 0.78
LHLP10221K RoHS 220 0.70 0.63
LHLP10331K RoHS 330 0.88 0.58
LHLP10471K RoHS 470 1.3 0.46
LHLP10681K RoHS 680 1.9 0.38
LHLP10102K RoHS 1000 0.252 3.2 0.30
Please specify the packaging code. (TB: Taping, NB: Bulk)
LHLP12NB
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Nominal Inductance
[μH]
L Measuring
frequency
Inductance
Tolerance
DC Resistance
[Ω] (max.)
Rated current
A (max.)
LHLP12NB150M RoHS 15
2.52 ±20
0.035 3.3
LHLP12NB220M RoHS 22 0.050 2.7
LHLP12NB330M RoHS 33 0.070 2.4
LHLP12NB470M RoHS 47 0.081 2.1
LHLP12NB680M RoHS 68 0.12 1.7
LHLP12NB101K RoHS 100
0.796 ±10
0.16 1.6
LHLP12NB151K RoHS 150 0.24 1.3
LHLP12NB221K RoHS 220 0.38 0.95
LHLP12NB331K RoHS 330 0.46 0.89
LHLP12NB471K RoHS 470 0.69 0.74
LHLP12NB681K RoHS 680 1.1 0.58
LHLP12NB102K RoHS 1000 0.252 1.8 0.46
LHL13
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
min.
Self-resonant
frequency
MHz (min.)
DC Resistance
[Ω] (max.)
Rated current
A (max.)
Measuring
frequency
MHz
LHL13100 K RoHS 10
±10
140 19 0.023 4.5
2.52
LHL13150K RoHS 15 12 0.028 4.0
LHL13220K RoHS 22 100 7.6 0.035 3.4
LHL13330K RoHS 33 6.9 0.043 3.2
LHL13470K RoHS 47 70 5.6 0.052 2.8
LHL13680K RoHS 68
50
4.4 0.070 2.4
LHL13101K RoHS 100 3.3 0.12 2.0
0.796
LHL13151K RoHS 150 2.6 0.19 1.5
LHL13221K RoHS 220 40 2.2 0.23 1.3
LHL13331K RoHS 330
30
1.8 0.35 1.1
LHL13471K RoHS 470 1.5 0.43 0.90
LHL13681K RoHS 680 1.2 0.61 0.80
LHL13102J RoHS 1000
±5
1.0 1.2 0.60
0.252
LHL13152J RoHS 1500
40
0.83 1.8 0.45
LHL13222J RoHS 2200 0.70 2.2 0.40
LHL13332J RoHS 3300 0.60 3.4 0.33
LHL13472J RoHS 4700 0.43 4.7 0.28
LHL13682J RoHS 6800 30 0.38 5.6 0.25
LHL13103J RoHS 10000 70 0.30 10 0.19 L:1kHz
Q:0.0796MHz
Please specify the packaging code. (TB: Taping, NB: Bulk)
116
1
2
leaded_i02_e-01
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
PART NUMBERS
LHLC08
Ordering code
EHS
(
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Self-resonant
frequency
MHz (min.)
DC Resistance
[Ω]
(max.)
Rated current
A
(max.)
Measuring
frequency
MHz
LH LC081R0N RoHS 1.0 ±30
40
76 0.013 5.4
7.96
LH LC081R5M RoHS 1.5
±20
65 0.014 5.2
LH LC082R2M RoHS 2.2 56 0.017 4.8
LH LC082R7M RoHS 2.7 48 0.019 4.2
LH LC083R3M RoHS 3.3 41 0.021 3.8
LH LC083R9M RoHS 3.9 33 0.024 3.7
LH LC084R7M RoHS 4.7 30 0.025 3.6
LH LC085R6M RoHS 5.6 23 0.028 3.5
LH LC086R8M RoHS 6.8 21 0.030 3.4
LH LC088R2M RoHS 8.2 19 0.034 3.0
LH LC08100K RoHS 10
±10
65 17 0.041 2.9
2.52
LH LC08120K RoHS 12 16 0.044 2.8
LH LC08150K RoHS 15
50
13 0.053 2.6
LH LC08180K RoHS 18 12 0.060 2.4
LH LC08220K RoHS 22 11 0.068 2.3
LH LC08270K RoHS 27
±10
50 10 0.091 2.0
2.52
LH LC08330K RoHS 33
40
8.8 0.10 1.9
LH LC08390 K RoHS 39 8.4 0.12 1.7
LH LC08470K RoHS 47 8.2 0.15 1.5
LH LC08560K RoHS 56 7.9 0.17 1.4
LH LC08680 K RoHS 68 35 7.0 0.20 1.3
LH LC08820K RoHS 82 6.5 0.22 1.2
LH LC08101K RoHS 100 25 5.7 0.32 1.0
0.796
LH LC08121K RoHS 120 5.2 0.36 0.96
LH LC08151K RoHS 150 20 4.7 0.41 0.88
LH LC08181K RoHS 180 35 4.2 0.66 0.71
LH LC08221K RoHS 220 3.7 0.73 0.66
LH LC08271K RoHS 270 25 3.5 0.85 0.63
LH LC08331K RoHS 330 3.2 0.97 0.59
LH LC08391K RoHS 390 20 2.9 1.1 0.55
LH LC08471K RoHS 470
25
2.4 1.3 0.49
LH LC08561K RoHS 560 2.2 1.5 0.47
LH LC08681K RoHS 680 2.0 1.8 0.44
LH LC08821K RoHS 820 30 1.6 2.3 0.38
LH LC08102J RoHS 1000
±5
55 1.5 2.7 0.35
0.252
LH LC08122J RoHS 1200 45 1.4 3.2 0.31
LH LC08152J RoHS 1500
55
1.3 4.1 0.29
LH LC08182J RoHS 1800 1.2 4.8 0.26
LH LC08222J RoHS 2200 1.1 5.6 0.23
LH LC08272J RoHS 2700 1.0 7.5 0.21
LH LC08332J RoHS 3300 0.85 8.5 0.19
LH LC08392J RoHS 3900 0.78 9.7 0.18
LH LC08472J RoHS 4700
65
0.68 14 0.16
LH LC08562J RoHS 5600 0.62 16 0.15
LH LC08682J RoHS 6800 0.61 18 0.14
LH LC08822J RoHS 8200 0.60 20 0.13
LH LC08103J RoHS 10000
60
0.48 32 0.11
L:1kHz
Q:0.0796
LH LC08123J RoHS 12000 0.44 36 0.084
LH LC08153J RoHS 15000 0.35 62 0.068
LH LC08183J RoHS 18000 0.30 72 0.066
LH LC08223J RoHS 22000 0.28 82 0.057
LH LC08273J RoHS 27000 0.25 90 0.054
LH LC08333J RoHS 33000 0.23 100 0.053
Please specify the packaging code. (TB: Taping, NB: Bulk)
LHLP16NB
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Nominal Inductance
[μH]
L Measuring
frequency
Inductance
Tolerance
DC Resistance
[Ω] (max.)
Rated current
A (max.)
LHLP16NB100M RoHS 10
1kHz
±20
0.019 5.2
LHLP16NB150M RoHS 15 0.025 5.1
LHLP16NB220M RoHS 22 0.027 4.6
LHLP16NB330M RoHS 33 0.035 4.0
LHLP16NB470K RoHS 47
±10
0.045 3.4
LHLP16NB680K RoHS 68 0.062 3.1
LHLP16NB101K RoHS 100 0.091 2.3
LHLP16NB151K RoHS 150 0.14 1.9
LHLP16NB221K RoHS 220 0.20 1.5
LHLP16NB331K RoHS 330 0.31 1.3
LHLP16NB471K RoHS 470 0.47 1.0
LHLP16NB681K RoHS 680 0.58 0.98
LHLP16NB102K RoHS 1000 0.94 0.74
117
1
2
leaded_i02_e-01
INDUCTORS
LEADED INDUCTORS
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
PART NUMBERS
LHLC10
Ordering code
EHS
(
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Self-resonant
frequency
MHz (min.)
DC Resistance
[Ω]
(max.)
Rated current
A
(max.)
Measuring
frequency
MHz
LH LC103R3M RoHS 3.3
±2050
46 0.019 5.0
7.96
LH LC103R9M RoHS 3.9 40 0.022 4.8
LH LC104R7M RoHS 4.7 38 0.024 4.7
LH LC105R6M RoHS 5.6 34 0.025 4.5
LH LC106R8M RoHS 6.8 30 0.028 4.1
LH LC108R2M RoHS 8.2 24 0.031 3.9
LH LC10100K RoHS 10
±10
90
19 0.034 3.6
2.52
LH LC10120K RoHS 12 16 0.038 3.4
LH LC10150K RoHS 15 12 0.042 3.2
LH LC10180K RoHS 18 9.2 0.046 3.0
LH LC10220K RoHS 22
60
8.6 0.061 2.8
LH LC10270K RoHS 27 7.1 0.069 2.7
LH LC10330 K RoHS 33 6.8 0.078 2.6
LH LC10390K RoHS 39 6.7 0.085 2.4
LH LC10470K RoHS 47 50 6.2 0.093 2.3
LH LC10560 K RoHS 56 5.2 0.10 2.1
LH LC106 80K RoHS 68
40
4.6 0.12 2.0
LH LC10820K RoHS 82 4.7 0.13 1.8
LH LC10101K RoHS 100 3.8 0.18 1.5
0.796
LH LC10121K RoHS 120 3.2 0.25 1.3
LH LC10151K RoHS 150 2.9 0.29 1.2
LH LC10181K RoHS 180 2.6 0.40 1.0
LH LC10221K RoHS 220 2.3 0.44 0.97
LH LC10271K RoHS 270
±1030
2.1 0.50 0.90
LH LC10331K RoHS 330 2.0 0.56 0.86
LH LC10391K RoHS 390 1.8 0.62 0.75
LH LC10471K RoHS 470 1.7 0.84 0.65
LH LC10561K RoHS 560 1.5 0.93 0.61
LH LC106 81K RoHS 680 1.4 1.0 0.57
LH LC10821K RoHS 820 1.3 1.4 0.50
LH LC10102J RoHS 1000
±5
50
1.2 1.8 0.48
0.252
LH LC10122J RoHS 1200 0.87 2.3 0.40
LH LC10152J RoHS 1500 0.83 2.7 0.37
LH LC10182J RoHS 1800 0.75 3.0 0.36
LH LC10222J RoHS 2200 0.70 3.9 0.32
LH LC10272J RoHS 2700 0.67 4.3 0.30
LH LC10332J RoHS 3300 0.56 5.8 0.26
LH LC10392J RoHS 3900 0.54 6.4 0.25
LH LC10472J RoHS 4700 0.49 7.1 0.24
LH LC10562J RoHS 5600 0.41 9.0 0.21
LH LC106 82J RoHS 6800 0.38 10 0.20
LH LC10822J RoHS 8200 0.36 12 0.18
LH LC10103J RoHS 10000
60
0.29 19 0.14
L:1kHz
Q:0.0796
LH LC10123J RoHS 12000 0.27 21 0.13
LH LC10153J RoHS 15000 0.24 34 0.11
LH LC10183J RoHS 18000 0.21 38 0.10
LH LC10223J RoHS 22000 0.20 43 0.095
LH LC10273J RoHS 27000
40
0.15 67 0.076
LH LC10333J RoHS 33000 0.14 76 0.068
LH LC10393J RoHS 39000 0.13 84 0.065
LH LC10473J RoHS 47000 0.12 96 0.061
LH LC10563J RoHS 56000
30
0.10 170 0.045
LH LC106 83J RoHS 68000 0.095 200 0.043
LH LC10823J RoHS 82000 0.088 210 0.041
LH LC10104J RoHS 100000 0.085 240 0.038 L:1kHz
Q:0.0252
LH LC10124J RoHS 120000 0.070 260 0.037
LH LC10154 J RoHS 150000 0.069 300 0.035
Please specify the packaging code. (TB: Taping, NB: Bulk)
118
1
2
leaded_i02_e-01
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
ELECTRICAL CHARACTERISTICS
DC Bias characteristics
LHL08
LHL10
LHL13
LHL16
LHLP10
LHLP12
LHLP16
119
1
2
leaded_i02_e-01
INDUCTORS
LEADED INDUCTORS
ELECTRICAL CHARACTERISTICS
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Q-vs-Frequency characteristics
Temperature characteristics
LHLC10
1000000
100000
10000
1000
100
10
1
0.01 0.1 1 10
154J
104J
473J
223J
103J
472J
222J
102J
471K
221K
101K
470K
220K
100K
3R3M
LHLC08
100000
10000
1000
100
10
1
0.1
0.01 0.1 1 10
333
223
103
472
222
102
471
221
101
470K
220
100
4R7
2R2
1R0
Measured by HP4284A
DC Bias characteristics
1
2
leaded_i02_pack-P1 leaded_i02_pack_e-01
PACKAGING
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Minimum Quantity
Type (EIA) Standard quantity (pcs)
Box Bulk Taped
LHL 08 100 1000
LHL 10 50 500
LHL 13 25 500
LHL 16 500250
LHLP10 500 200
LHLP12NB 300
LHLP16NB 200
LHLC08 100 1000
LHLC10 50 500
Bulk dimensions
LHL0816
LHLP1016
Type Dimensions
φDmaxH2
maxF φd
LHL08 9.0 9.5 5.0±1.0 5.0±1.0 0.6±0.05
0.354 0.374 0.197±0.0390.197±0.0390.024±0.002
LHL10 11.0 14.0 5.0±1.0 5.0±1.0 0.6±0.05
0.433 0.551 0.197±0.0390.197±0.0390.024±0.002
LHL13 14.0 17.0 7.5±1.0 5.0±1.0 0.8±0.05
0.551 0.669 0.295±0.0390.197±0.0390.031±0.002
LHL16 17.0 21.0 7.5±1.0 5.0±1.0 0.8±0.05
0.669 0.827 0.295±0.0390.197±0.0390.031±0.002
*Measured at the base of the leads. Unitmminch
Type Dimensions
φDmaxH2
maxF φd
LHLP10 11.0 11.0 5.0±1.0 5.0±1.0 0.6±0.05
0.433 0.433 0.197±0.0390.197±0.0390.024±0.004
LHLP12 13.0 16.0 5.0±1.0 5.0±1.0 0.6±0.05
0.512 0.624 0.197±0.0390.197±0.0390.024±0.004
LHLP16 17.0 19.0 7.5±1.0 5.0±1.0 0.8±0.05
0.669 0.741 0.295±0.0390.197±0.0390.031±0.004
*Measured at the base of the leads. Unitmminch
LHL0816
LHLP10TB
LHL08 LHL10 LHL13 LHL16
Dφ9.0 max φ11.0 max φ14.0 max φ17.0 max
(φ0.354 max (φ0.433 max (φ0.551 max (φ0.669 max
H1
30.5 max 34.0 max 37.0 max 41.0 max
1.20 max 1.34 max 1.46 max 1.61 max
H18.02.0
0.0 18.02.0
0.0 18.02.0
0.0 18.02.0
0.0
0.7090.079
0.000 0.7090.079
0.000 0.7090.079
0.000 0.7090.079
0.000
H2
9.5 max 14.0 max 17.0 max 21.0 max
0.374 max 0.551 max 0.669 max 0.827 max
LHL08 LHL10 LHL13 LHL16
P12.7±1.0 12.7±1.0 15.0±1.0 30.0±1.0
0.500±0.039 0.500±0.039 0.591±0.039 1.18±0.039
P0
12.7±0.3112.7±0.3115.0±0.3115.0±0.31
0.500±0.012 0.500±0.012 0.591±0.012 0.591±0.012
P1
3.85±0.7 3.85±0.7 3.75±0.7 3.75±0.7
0.152±0.028 0.152±0.028 0.148±0.028 0.148±0.028
P2
6.35±1.3 6.35±1.3 7.50±1.3 7.50±1.3
0.250±0.051 0.250±0.051 0.295±0.051 0.295±0.051
F5.00.8
0.2 5.00.8
0.2 7.500.8
0.2 7.50±0.5
0.1970.031
0.008 0.1970.031
0.008 0.2950.031
0.0080.295±0.020
h0.0±2.0 0.0±2.0 0.0±2.0 0.0±2.0
0.0±0.079 0.0±0.079 0.0±0.079 0.0±0.079
W18.01.0
0.5 18.01.0
0.5 18.01.0
0.5 18.01.0
0.5
0.7090.039
0.020 0.7090.039
0.020 0.7090.039
0.020 0.7090.039
0.020
W0
12.5 min 12.5 min 12.5 min 12.5 min
0.492 min 0.492 min 0.492 min 0.492 min
W1
9.0±0.5 9.0±0.5 9.0±0.5 9.0±0.5
0.354±0.020 0.354±0.020 0.354±0.020 0.354±0.020
W2
3.0 max23.0 max23.0 max23.0 max2
0.118 max 0.118 max 0.118 max 0.118 max
D0
φ4.0±0.2 φ4.0±0.2 φ4.0±0.2 φ4.0±0.2
(φ0.158±0.008(φ0.158±0.008(φ0.158±0.008(φ0.158±0.008
φdφ0.6±0.05 φ0.6±0.05 φ0.8±0.05 φ0.8±0.05
(φ0.024±0.002(φ0.024±0.002(φ0.031±0.002(φ0.031±0.002
t0.6±0.3 0.6±0.3 0.6±0.3 0.6±0.3
0.024±0.012 0.024±0.012 0.024±0.012 0.024±0.012
D1
φ1.8 φ1.8 φ1.8
0.071 0.071 0.071
P3
6.35 6.35 7.50
0.25 0.25 0.25
1 Accumulated error for 20 pitches is 1mm.
2 Bonding tape must not protrude from the base tape.
Unitmminch
Type Symbol Dimensions Symbol Dimensions
LHLP10
Dφ11.0 max W18.01.0
0.5
(φ0.433 max0.7090.039
0.020
H1
32.0 max W0
12.5 min
1.26 max 0.492 min
H18.02.0
0.0 W1
9.0±0.5
0.7090.079
0.0000.354±0.020
H2
11.0 max W2
3.0 max2
0.433 max 0.118 max
P12.7±1.0 D0
φ4.0±0.2
0.500±0.039 (φ0.158±0.008
P0
12.7±0.31
φdφ0.6±0.05
0.500±0.012 (φ0.024±0.002
P1
3.85±0.7 t0.6±0.3
0.152±0.028 0.024±0.012
P2
6.35±1.3 D1
φ1.8
0.250±0.051 0.071
F5.00.8
0.2 P3
6.35
0.1970.031
0.0080.25
h0.0±2.0 Unitmminch
0.0±0.079
1 Accumulated error for 20 pitches is 1mm.
2 Bonding tape must not protrude from the base tape.
1
2
leaded_i02_pack-P2 leaded_i02_pack_e-01
PACKAGING
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
LHLC08, LHLC10
LHLC08 LHLC10
Dφ9.0max
(φ0.354maxφ11.0max
(φ0433max
H1
30.5max
1.20max34.0max
1.34max
H18.02.0
0.0
0.709
0.079
0.000
18.02.0
0.0
0.709
0.079
0.000
H2
9.5max
0.374max14.0max
0.551max
P12.7±1.0
0.500±0.03912.7±1.0
0.500±0.039
P0
12.7±0.31
0.500±0.01212.7±0.31
0.500±0.012
P1
3.85±0.7
0.152±0.0283.85±0.7
0.152±0.028
P2
6.35±1.3
0.250±0.0516.35±1.3
0.250±0.051
F5.00.8
0.2
0.197
0.031
0.008
5.00.8
0.2
0.197
0.031
0.008
h0.0±2.0
0.0±0.0790.0±2.0
0.0±0.079
W18.01.0
0.5
0.709
0.039
0.020
18.01.0
0.5
0.709
0.039
0.020
W0
12.5min
0.492min12.5min
0.492min
W1
9.0±0.5
0.354±0.020
9.0±0.5
0.354±0.020
W2
3.0max2
0.118max3.0max2
0.118max
D0
φ4.0±0.2
(φ0.158±0.008φ4.0±0.2
(φ0.158±0.008
φdφ0.6±0.05
(φ0.024±0.002φ0.6±0.05
(φ0.024±0.002
t0.6±0.3
0.024±0.0120.6±0.3
0.024±0.012
D1
φ1.8
0.071φ1.8
0.071
P3
6.35
0.256.35
0.25
1 Accumulated error for 20 pitches is 1mm. Unitmminch
2 Bonding tape must not protrude from the base tape.
Type
Dimensions
φD
(max) H2 (max) F φd
LHLC08
9.0
0.354
9.5
0.374
5.0±1.0
0.197±0.039
5.0±1.0
0.197±0.039
0.6±0.05
0.024±0.002
LHLC10
11.0
0.433
14.0
0.551
5.0±1.0
0.197±0.039
5.0±1.0
0.197±0.039
0.6±0.05
0.024±0.002
*Measured at the base of the leads. Unitmminch
1
2
le0104fi01_reli-RP1 le0104fi01_reli_e-01
RELIABILITY DATA
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Operating temperature Range
LA Type
25~+105CAL45 Type
LHL□□□
FBA/FBR 2585
FL05 Type 25~+105
FL06BT Type
Test Method and Remarks
LACAFL : Including self-generated heat
LHL□□□ : Including self-generated heat
3. Rated current
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : The maximum DC value having inductance within 10% and temperature incease within 40 (LA:20) by the application of DC bias.
LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10within 30%) and temperature increase within the following specified
temperature by the application of DC bias.
Reference temperature : 25 (LHL08, LHL10, LHL13)
: 30 (LHL16, LHLP)
: 40 (LHLC08, LHLC10)
FB : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value.
This is not guaranteed for electrial characteristics during current application.
FL : The maximum DC value having temperature rise within specified value.
5. Inductance
LA Type
Within the specified toleranceCAL45 Type
LHL□□□
FBA/FBR
FL05 Type Within the specified tolerance
FL06BT Type
Test Method and Remarks
LA, CA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ : Measuring equipment : LCR meter (HP4285AHP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
FL05R : Measuring equipment : HP4262A or its equivalent
Measuring frequency : 1kHz
6. Q
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285AHP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
2. Storage temperature Range
LA Type
40~+85
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
4. Impedance
LA Type
CAL45 Type
LHL□□□
FBA/FBR Within the specified tolerance
FL05 Type
FL06BT Type Refer to individual specification
Test Method and Remarks
FB : Measuring equipment : Impedance analyzer (HP4191A) or its equivalent
Measuring frequency : Specified frequency
FL06BT : Measuring equipment : 4291A (HP) or its equivalent
Measuring frequency : Specified frequency
1
2
le0104fi01_reli-RP2
le0104fi01_reli_e-01
RELIABILITY DATA
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
11. Over current
LA Type No emission of smoke no firing.
CAL45 Type
LHL□□□ There shall be no scorch or short of wire.
LHLC08,LHLC10 : There shall be no firing.
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LHL□□□/LACAL45 Type Measuring current : Rated current×2
Duration : 5 min.
Number of measuring : one time
8. Self resonance frequency
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA : Measuring equipment : Network analyzer (Anritsu MS620J or its equivalent)
LHL□□□ (except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent
9. Temperature characteristic
LA Type L/L : Within ±5%
CAL45 Type
LHL□□□ L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA : Change of maximum inductance deviation in step 1 to 5
Step Temperature ()
1 20
225 (Minimum operating temperature)
3 20 (Standard temperature)
485 (Maximum operating temperature)
5 20
LHL□□□ : Change of maximum inductance deviation in step 1 to 5
Temperature at step 1 : 20
Temperature at step 2 : Minimum operating temperature
Temperature at step 3 : 20 (Standard temperature)
Temperature at step 4 : Maximum operating temperature
Temperature at step 5 : 20
10. Tensile strength test
LA Type
No abnormality such as cut lead, or looseness.CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cut lead, or looseness.
FL05 Type No abnormality such as cut lead, or looseness.
FL06BT Type
Test Method and Remarks
LA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
25 5
CA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
10 10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm) force (N) duration (s)
0.3φd0.5 5
30±50.5φd0.8 10
0.8φd1.2 25
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the axial diretion of the component during 10±1 seconds.
FL05R : Fix the body of a component in the direction to draw terminal,and gradually apply the tensile force of 4.9N.
7. DC Resisitance
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent)
LHL□□□FBFL : Measuring equipment : DC ohmmeter
1
2
le0104fi01_reli-RP3 le0104fi01_reli_e-01
RELIABILITY DATA
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
12. Terminal strength : bending
LA Type
No abnormality such as cut lead, or looseness.
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.3φd0.5 2.5 0.25
0.5φd0.8 5 0.50
LHFB : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.3φd0.5 2.5 0.25
0.5φd0.8 5 0.5
0.8φd1.2 10 1.0
13. Insulation resisitance : between the terminals and body
LA Type
CAL45 Type
LHL□□□ 100MΩ min.
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LHL□□□ : Applied voltage : 500 VDC
Duration : 60 sec.
14. Insulation resistance : between terminals and core
LA Type
CAL45 Type
LHL□□□
FBA/FBR 1MΩ min. (Other than materail code MA)
FL05 Type
FL06BT Type
Test Method and Remarks
FBAFBR : Applied voltage : 100 VDC
Duration : 60±5 sec.
15. Withstanding : between the terminals and body
LA Type
CAL45 Type
LHL□□□ No abnormality such as insulation damage
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LHL□□□ : Accoding to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage : 500 VDC
Duration : 60 sec.
16. DC bias characteristic
LA Type L/L : Within 10%
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : Measure inductance with appliation of rated current using LCR meter to compare it with the initial value.
17. Body strength
LA Type No abnormality as damage.
CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cracks on body.
FL05 Type
FL06BT Type
Test Method and Remarks
LA : Applied force : 30N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
CAL45 : Applied force : 50N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
FBA : Applied force : 50±3N
Duration : 30±1 sec.
1
2
le0104fi01_reli-RP4
le0104fi01_reli_e-01
RELIABILITY DATA
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
18. Resisitance to vibration
LA Type L/L : Within ±5% Q : 30min
CAL45 Type L/L : Within ±5%
LHL□□□ Appearance : No abnomality L/L : Within ±5% Q change : Within ±30% (LHLP : only L/L)
FBA/FBR Appearance : No abnomality Impedance change : Within ±20%
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm
Mounting method : Soldering onto printed board.
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□FB Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm (But don't exceed acceleration 196m/s2 (two power))
Mounting method : Soldering onto printed board.
19. Resistance to shock
LA Type No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : Drop test
Impact material : concrete or vinyl tile
Height : 1m
Total number of drops : 10 times
20. Solderability
LA Type At least 75 of terminal electrode is covered by new solder.
CAL45 Type
LHL□□□ At least 75 of terminal electrode is covered by new solder.
FBA/FBR At least 90 of terminal electrode is covered by new solder.
FL05 Type At least 75 of terminal electrode is covered by new solder.
FL06BT Type
Test Method and Remarks
LA, CA : Solder temperature : 230±5
Duration : 2±0.5 sec.
LHL□□□ : Solder temperature : 235±5
Duration : 2±0.5 sec.
Immersion depth : Up to 1.5mm from bottom of case.
FB : Solder temperature : 230±5
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from terminal root.
FL05R : Solder temperature : 230±5
Duration : 2±0.5 sec.
Immersion depth : Up to 2 to 2.5mm from terminal root.
FL06BT : Solder temperature : 230±5
Duration : 3±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from terminal root.
21. Resisitance to soldering heat
LA Type No significant abnormality in appearance
CAL45 Type L/L : Within ±5%
LHL□□□ No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30%(LHLP : only L/L)
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05 Type Refer to individual specification
FL06BT Type No significant abnormality in appearance Impedance change : Within ±20%
Test Method and Remarks
LA, CA : Solder temperature : (CA) 270±5, (LA) 260±5
Duration : 5±0.5 sec. One time
Immersed conditions : Inserted into substrate with t=1.6mm
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□ : Solder bath method : Solder temperature : 260±5
Duration : 10±1 sec.
Up to 1.5mm from the bottom of case.
Manual soldering : Solder temperature : 350±10 (At the tip of soldering iron)
Duration : 5±1 sec.
Up to 1.5mm from the bottom of case.
Caution : No excessive pressing shall be applied to terminals.
Recovery : 4 to 24hrs of recovery under the standard condition after the test.
FB : Solder bath method : Condition 1 : Solder temperature : 260±5
Duration : 10±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Condition 2 : Solder temperature : 350±5
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
FL : Solder condition : 260±5 10±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from the terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
1
2
le0104fi01_reli-RP5 le0104fi01_reli_e-01
RELIABILITY DATA
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
22. Resisitance to solvent
LA Type Please avoid the ultrasonic cleaning of this product.
CAL45 Type
LHL□□□
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05 Type
FL06BT Type
Test Method and Remarks
FB : Solvent temperature : 2025
Duration : 30±5 sec.
Solvent type : Acetone
Recovery : 3hrs of recovery under the standard condition after the test.
23. Thermal shock
LA Type L/L : Within ±10% Q : 30min
CAL45 Type L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLPonly L/L)
FBA/FBR Appearance : No abnormality Impedance change : Within ±20%
FL05 Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
Test Method and Remarks
LA, CA : Conditions for 1cycle
Step Temperature () Duration (min.)
1250
330±3
2 Room temperature Within 3
3852
030±3
4 Room temperature Within 3
Number of cycles : 5 cycles
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
LHL□□FB : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature () Duration (min.)
1 Minimum operating temperature0
330±3
2 Room temperature Within 3
3 Minimum operating temperature2
030±3
4 Room temperature Within 3
Number of cycles : 10 cycles LHL□□〕
: 5 cycles (FBA, FBR)
Recovery : 4 to 24hrs of recovery under the standard condition after the removal from the test chamber. LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR)
FL : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature () Duration (min.)
1250
330±3
2 Room temperature Within 3
3852
030±3
4 Room temperature Within 3
Number of cycles : 10 cycles
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
24. Damp heat
LA Type L/L : Within ±10% Q : 30min
CAL45 Type L/L : Within ±10%
LHL□□□
FBA/FBR AppearanceNo abnormality Impedance changeWithin ±20%
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : Temperature : 40±2
Humidity : 9095%RH
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
FB : Temperature : 60±2
Humidity : 9095%RH
Duration : 1000 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
1
2
le0104fi01_reli-RP6
le0104fi01_reli_e-01
RELIABILITY DATA
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
25. Loading under damp heat
LA Type L/L : Within ±10% Q : 30min
CAL45 Type L/L : Within ±10%
LHL□□□ Appearance : No abnormality Imductance change : Within ±10% Q change : Within ±30% (LHLP : only L/L)
FBA/FBR
FL05 Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
Test Method and Remarks
LA, CA : Temperature : 40±2
Humidity : 9095%RH
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : 40±2
Humidity : 9095%RH
Duration : 1000±24 hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 60±3
Humidity : 9095%RH
Duration : 500 (12, 0) hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
LA Type L/L : Within ±10% Q : 30min
CAL45 Type L/L : Within ±10%
LHL□□□
FBA/FBR
FL05 Type
FL06BT Type
Test Method and Remarks
LA, CA : Temperature : 85±2
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
LA Type L/L : Within ±10% Q : 30min
CAL45 Type L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only L/L)
FBA/FBR
FL05 Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
Test Method and Remarks
LA, CA : Temperature : 25±2
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : 40±3
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 40±3
Duration : 500 (12, 0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
LA Type
CAL45 Type
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only L/L)
FBA/FBR
FL05 Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
Test Method and Remarks
LHL□□□ : Temperature : 105±3
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 85±3
Duration : 500 (12, 0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
1
2
le0104fi01_reli-RP7 le0104fi01_reli_e-01
PRECAUTIONS
This catalog contains the typical specication only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Circuit Design
Precautions
Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(ofce supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions Design
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
Technical
consider-
ations
Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
Precautions
Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
consider-
ations
Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc
sufficiently.
Recommended conditions for using a soldering iron:
Put the soldering iron on the land-pattern.
Soldering iron's temperature - Below 350
Duration - 3 seconds or less
The soldering iron should not directly touch the inductor.
Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical
consider-
ations
Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
5. Cleaning
Precautions
Cleaning conditions
1. CAL type, LH type, LA Type
Please do not do cleaning by a supersonic wave.
Technical
consider-
ations
Cleaning conditions
1. CAL type, LH type, LA Type
If washing by supersonic waves, supersonic waves may deform products.
6. Handling
Precautions
Handling
1. Keep the inductors away from all magnets and magnetic objects.
Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
Technical
consider-
ations
Handling
1. There is a case that a characteristic varies with magnetic influence.
Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
Precautions
Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
Recommended conditions
Ambient temperature 040
Humidity Below 70% RH
The ambient temperature must be kept below 30. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
consider-
ations
Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
CAL Type, LH Type, FB Type, FL Type, LA Type