0201ZD122KAT2A - AVX Corporation - Datasheet.Directory

• General Purpose Dielectric for Ceramic Capacitors

• EIA Class II Dielectric

• Temperature variation of capacitance is within ±15%

from -55°C to +85°C

• Well suited for decoupling and filtering applications

• Available in High Capacitance values (up to 100µF)

X5R Dielectric

General Specifications

PART NUMBER (see page 2 for complete part number explanation)

GENERAL DESCRIPTION

%  Capacitance

-60 -40 -20 0 +20 +40 +60 +80

Temperature °C

Temperature Coefficient

-5

-10

-15

-20

TYPICAL ELECTRICAL CHARACTERISTICS

Insulation Resistance (Ohm-Farads)

1,000

10,000

100

Insulation Resistance vs Temperature

020 120

40 60 80

Temperature °C

100

2220

Size

(L" x W")

Voltage

4 = 4V

6 = 6.3V

Z = 10V

Y = 16V

3 = 25V

D = 35V

Dielectric

D = X5R

107

Capacitance

Code (In pF)

2 Sig. Digits +

Number of

Zeros

Capacitance

Tolerance

K = ±10%

M = ±20%

Failure

Rate

A = N/A

Terminations

T = Plated Ni

and Sn

Packaging

2 = 7" Reel

4 = 13" Reel

7 = Bulk Cass.

9 = Bulk

Special

Code

A = Std.

X5R Dielectric

Specifications and Test Methods

Parameter/Test X5R Specification Limits Measuring Conditions

Operating Temperature Range -55ºC to +85ºC Temperature Cycle Chamber

Capacitance Within specified tolerance

≤2.5% for ≥50V DC rating Freq.: 1.0 kHz ± 10%

Dissipation Factor ≤3.0% for 25V DC rating Voltage: 1.0Vrms ± .2V

≤3.5% for 16V DC rating For Cap > 10 µF, 0.5Vrms @ 120Hz

≤5.0% for ≤10V DC rating

Insulation Resistance 100,000MΩor 500MΩ- µF, Charge device with rated voltage for

whichever is less 60 ± 5 secs @ room temp/humidity

Charge device with 300% of rated voltage for

Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current

limited to 50 mA (max)

Appearance No defects Deflection: 2mm

Capacitance Test Time: 30 seconds

Resistance to Variation ≤±12%

Flexure Dissipation Meets Initial Values (As Above)

Stresses Factor

Insulation ≥Initial Value x 0.3

Resistance

Solderability ≥95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC

with fresh solder for 5.0 ± 0.5 seconds

Appearance No defects, <25% leaching of either end terminal

Capacitance

Variation ≤±7.5%

Dip device in eutectic solder at 260ºC for 60

Dissipation Meets Initial Values (As Above) seconds. Store at room temperature for 24 ± 2

Resistance to Factor hours before measuring electrical properties.

Solder Heat Insulation Meets Initial Values (As Above)

Resistance

Dielectric Meets Initial Values (As Above)

Strength

Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes

Capacitance

Variation ≤±7.5% Step 2: Room Temp ≤3 minutes

Dissipation Meets Initial Values (As Above) Step 3: +85ºC ± 2º 30 ± 3 minutes

Thermal Factor

Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤3 minutes

Resistance

Dielectric Meets Initial Values (As Above) Repeat for 5 cycles and measure after

Strength 24 ± 2 hours at room temperature

Appearance No visual defects

Capacitance

Variation ≤±12.5%

Dissipation ≤Initial Value x 2.0 (See Above)

Load Life Factor

Insulation ≥Initial Value x 0.3 (See Above)

Resistance

Dielectric Meets Initial Values (As Above)

Strength

Appearance No visual defects

Capacitance

Variation ≤±12.5%

Load Dissipation ≤Initial Value x 2.0 (See Above)

Humidity Factor

Insulation ≥Initial Value x 0.3 (See Above)

Resistance

Dielectric Meets Initial Values (As Above)

Strength

Charge device with twice rated voltage in

test chamber set at 85ºC ± 2ºC

for 1000 hours (+48, -0)

Remove from test chamber and stabilize

at room temperature for 24 ± 2 hours

before measuring.

Store in a test chamber set at 85ºC ± 2ºC/

85% ± 5% relative humidity for 1000 hours

(+48, -0) with rated voltage applied.

Remove from chamber and stabilize at

room temperature and humidity for

24 ± 2 hours before measuring.

1mm/sec

90 mm

X5R Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

SIZE 0201 0402 0603 0805 1206 1210 1812 2220

Soldering

Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Reflow Only Reflow Only

Packaging

All Paper All Paper All Paper Paper/Embossed Paper/Embossed Paper/Embossed All Embossed All Embossed

(L) Length MM 0.60 ± 0.03 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20 3.20 ± 0.20 4.50 ± 0.30 5.70 ± 0.40

(in.) (0.024 ± 0.001) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008) (0.126 ± 0.008) (0.177 ± 0.012) (0.225 ± 0.016)

(W) Width MM 0.30 ± 0.03 0.50 ± 0.10 0.81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20 2.50 ± 0.20 3.20 ± 0.20 5.00 ± 0.40

(in.) (0.011 ± 0.001) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008) (0.098 ± 0.008) (0.126 ± 0.008) (0.197 ± 0.016)

(t) Terminal MM 0.15 ± 0.05 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 0.50 ± 0.25 0.61 ± 0.36 0.64 ± 0.39

(in.) (0.006 ± 0.002) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010) (0.020 ± 0.010) (0.024 ± 0.014) (0.025 ± 0.015)

WVDC 10 4 6.3 10 16 4 6.3 10 16 25 6.3 10 16 25 35 6.3 10 16 25 35 4 6.3 10 16 25 35 6.3 10 16 25 6.3

Cap 100

(pF) 150

220

330

470

680

1000

1200 A

1500 A

1800 A

2200 A

2700 A

3300 A

3900 A

4700 A

5600 A

6800 A

8200 A

Cap. 0.010 A

(µF) 0.012

0.015

0.018

0.022

0.027 C C

0.033 C C

0.039 C C

0.047 C C

0.056 C G

0.068 C G

0.082 C G

0.10 C C C G

0.12 C G G

0.15 C G G

0.18 C G G

0.22 C G G G J N

0.27 G G G

0.33 G G G N N

0.47 G G G N N Q

0.56 G G G N M

0.68 G G G N N M

0.82 G G G N M

1.0 C G G G NN N QQ

1.2 G N Q

1.5 G N Q

1.8 G Q

2.2 G N Q X Z

3.3 NQ

4.7 J N N Q Q Q Q Q Z

6.8 N

10 NQQQXXXX Z

22 QZZZZ

47 ZZ

100 ZBBZ

WVDC 10 4 6.3 10 16 4 6.3 10 16 25 6.3 10 16 25 35 6.3 10 16 25 35 4 6.3 10 16 25 35 6.3 10 16 25 6.3

SIZE 0201 0402 0603 0805 1206 1210 1812 2220

Contact Factory for Multiples



Letter A C E G J K M N P Q X Y Z BB CC

Max. 0.33 0.56 0.71 0.86 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79 3.05 3.175

Thickness (0.013) (0.022) (0.028) (0.034) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110) (0.120) (0.125)

PAPER EMBOSSED