PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) Nominal Input Voltage Max. Output Power 120 to 277 Vac 50 W Efficiency Max. Case Temperature THD Power Factor Dimming Method Dimming Range Startup Time < 20% > 0.9 Forward-Phase, Reverse-Phase & 0 - 10V 1 - 100% (% of Iout) 200 ms typical up to 90% 90C (measured (from 100% to 50% (from 100% to 50% typical at the hot spot) TRIAC/ELV Dimmer + Dim - Dim PSB50 + LEDs Series - LEDs FEATURES 0-10 V Dimmer In fo rm of max rated power of max rated power) Aluminum Case L 98.5 * W 25.4 * H 19.05 mm (L 3.88 * W 1.00 * H 0.75 in.) White: Neutral m ina ry * Non-linear 0-10V dimming profile with dim-to-off (10V to 9.1V=100%, 1.5V to 0.6V=1%, <0.6V=dim-to-off) * UL Class P * Class 2 power supply * Lifetime: 50,000 hours @ Tc = 75C * 90C maximum case hot spot temperature * IP20-rated (IP64 as option) case with silicone-based potting * Surge protection: * IEC61000-4-5: 2 kV line to line/2 kV line to earth * 2.5 kV ring wave: ANSI/IEEE c62.41.1-2002 & c62.41.2-2002 category A * Complies with ENERGY STAR(R), DLC (DesignLight Consortium(R)) and CA Title 24 technical requirements PROGRAMMING eli Grey: - Dim PSB50 Series Red: + LEDs Black: Line Blue: - LEDs Wiring Diagram OTHER MOUNTING OPTIONS Bottom Leads with Studs Add "-X" suffix to part number. * Serial port programming * Current: 100% to 50% in each voltage range * Data log read: SKU, S/N, lot code, hours of operation, FW rev., fault events: power failure, transients (short or surge), thermal OPTIONS * Alternate 0-10V dimming profiles: Linear, Logarithmic, Ballast type Mark7 (IEC60929, ANSI C82.11) * Energy metering (as part of future software upgrade) Purple: + Dim European Terminal Blocks Add "-T" suffix to part number. APPLICATIONS Pr * Commercial & residential lighting * Architectural lighting * Indoor Lighting 5 CA Title 24 (c) ERP Power, LLC 1 PSB50/40/30 Series Data Sheet - Preliminary Information Rev. December 2017 PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) Nominal Input Voltage (Vac) Part Number Max Output Power (W) In fo rm 1 - ORDERING INFORMATION Iout (mA) Vout Vout Vout Min. Nom. Max. (Vdc) (Vdc) (Vdc) Open Loop (No Load) Voltage (Vdc) PSB30W PSB30W-0700-42 120 to 277 PSB30W-1050-27 120 to 277 PSB30W-0800-34 120 to 277 29.4 28.4 27.2 350 to 700 525 to 1050 400 to 800 27 17 20 37.8 24.3 30.6 42 27 34 50 35 44.2 17 24.3 27 35 54 36 27 20 76.5 50.4 37.8 30.6 85 56 42 34 100 60 50 44.2 PSB40W PSB40W-1400-27 120 to 277 37.8 700 to 1400 PSB50W 120 to 277 120 to 277 120 to 277 120 to 277 46.8 47.6 50.4 47.6 275 to 550 425 to 850 600 to 1200 700 to 1400 ina ry PSB50W-0550-85 PSB50W-0850-56 PSB50W-1200-42 PSB50W-1400-34 Pr eli m Notes: * For each model, the default output current setting is the maximum current. * To order the mounting option "Bottom Leads with Studs", add the suffix "-X". Example: PSB50W-1200-42-X * To order the mounting option "Terminal Blocks", add the suffix "-T". Example: PSB50W-1200-42-T * For additional options of output current and output voltage, contact your sales representative or send an email to: SaveEnergy@erp-power.com * Please order the programming cable using the part number "PROG-JACK-USB". SaveEnergy@erp-power.com 2 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 2 - INPUT SPECIFICATION (@25C ambient temperature) Typical Maximum 305 Input Voltage Range (Vin) Vac 90 120, 230, 277 Input Frequency Range Hz 47 50/60 63 0.5 A @ 120 Vac 0.23 A @ 277 Vac A Input Current (Iin) > 0.9 0.9 Power Factor (PF) 0.3 mA @ 120 Vac 0.6 mA @ 230 Vac Measured per IEC60950-1 0.7 mA @ 277 Vac mA Leakage Current At nominal input voltage and with nominal LED voltage From 100% to 50% of rated power At any point on the sine wave and 25C Active limiting inrush current is available as an option. Please contact your ERP representative or send an email to SaveEnergy@erp-power.com. Meets NEMA-410 requirements A Inrush Current Input Harmonics Complies with IEC61000-3-2 for Class C equipment Total Harmonics Distortion (THD) 20% % Efficiency Notes The rated output current for each model is achieved at Vin108 Vac & at Vin198 Vac At nominal load In fo rm Units Minimum - up to 90% - At nominal input voltage and nominal LED voltage From 100% to 50% of rated power Complies with DLC (Design Light Consortium) technical requirements Measured with nominal input voltage, a full sinusoidal wave form and without dimmer attached. Isolation ina ry The AC input to the main DC output is isolated and meets Class II reinforced/double insulation power supply 3 - MAIN OUTPUT SPECIFICATION (@25C ambient temperature) Output Voltage (Vout) Units Minimum Typical Maximum Vdc See ordering information for details See ordering information for details The rated output current for each model is achieved at Vin108 Vac & at Vin198 Vac. Output Current (Iout) mA Output Current Regulation % -5 2.5 5 % - - 10 10% of rated output current for each model eli Ripple Current m Output Current Overshoot % Start-up Time ms Pr Dimming Range (% of Iout) Isolation Notes 1 100 200 500 At nominal AC line voltage Includes load and current set point variations The driver does not operate outside of the regulation requirements for more than 500 ms during power on with nominal LED load and without dimmer. Measured at nominal LED voltage and nominal input voltage without dimming Calculated in accordance with the IES Lighting Handbook, 9th edition The dimming range is dependent on each specific dimmer. It may not be able to achieve 1% dimming with some dimmers. Dimming performance is optimal when the driver is operated at its nominal output voltage matching the LED nominal Vf (forward voltage). Dimming performance may vary when the driver is operated near its minimum output voltage. Without any dimmer attached, and at nominal input voltages and nominal load Measured from application of AC line voltage to 100% light output Complies with ENERGY STAR(R) luminaire specification and CA Title 24 The main DC output is certified and tested per UL8750 Class 2 or LED Class 2 SaveEnergy@erp-power.com 3 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 4 - 0-10 V DIMMING CONTROL (@25C ambient temperature) Units Minimum Typical Maximum Notes The PSB50/40/30 series operate only with 0-10V dimmers that sink current. The method to dim the output current of the driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim signal pins can be used to adjust the output setting via a standard commercial wall dimmer, an external control voltage source (0 to 10 Vdc), or a variable resistor when using the recommended number of LEDs. The dimming input permits 1% to 100% dimming. Dimming Profile (see figure 1) 100% of output current between 10 V and 9.1 V, Linear between 9.1 V and 1.5 V, 1% of output current between 1.5 V and 0.6 V, No output current below 0.6 V. Dimming Range High Level Voltage Low Level Voltage Dim to Off Current Supplied by the +Dim Signal Pin Output Current Tolerance While Being Dimmed 1 100 9.1 1.5 0.6 As a percent of the output current No output current mA 1 % 8 The tolerance of the output current while being dimmed is +/-8% until down to 1.5V. The 0-10 V circuit is isolated from the AC input and meets Class II reinforced/double insulation power supply. ina ry Isolation % V V V In fo rm +Dim Signal, -Dim Signal m Percent of Output Current (Normalized to Rated Current) 100% 1% Pr eli 0% SaveEnergy@erp-power.com 0.6 C 1.5 9.1 10 (V) Dimming Voltage (V) Dimming Voltage Description Value C hysteresis > 700 mV, < 800 mV Figure 1 4 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 5 - ENVIRONMENTAL CONDITIONS C Maximum Case Temperature (Tc) C Storage Temperature Humidity Cooling Acoustic Noise Mechanical Shock Protection Vibration Protection MTBF Lifetime C % Minimum Typical Maximum -20 50 Notes 50C is the non-derated temperature (Refer to section 8 "Output power de-rating at higher temperatures". In fo rm Units Operating Ambient Temperature (Ta) +90 -40 5 Convection cooled +85 95 Case temperature measured at the hot spot tc (see label in page 11) Non-condensing dBA 24 Measured at a distance of 1 meter, without dimmer per EN60068-2-27 per EN60068-2-6 & EN60068-2-64 > 200,000 hours when operated at nominal input and output conditions, and at Tc 75C 50,000 hours at Tc 75C maximum case hot spot temperature (see hot spot tc on label in page 11) 6 - EMC COMPLIANCE AND SAFETY APPROVALS cUL cUL CE Safety Agency Approvals UL8750 listed Class 2 (except PSB50W-0550-85) CAN/CSA C22.2 No. 250.13-14 LED equipment for lighting applications IEC61347-2-13 electronic control gear for LED Modules & EN55015 (EMC compliance) Pr CB ENEC eli m ina ry EMC Compliance Models with no suffix and with "-X" suffix: Compliant with FCC CFR Title 47 Part 15 Class B at 120 Vac & Class A at 277 Vac Conducted and Models with "-T" suffix: Compliant with FCC CFR Title 47 Part 15 Class B at 120 Vac and Class A at 277 Vac and with Radiated EMI EN55015 (CISPR 15) at 220, 230, and 240 Vac IEC61000-3-2 For Class C equipment Harmonic Current Emissions IEC61000-3-3 Voltage Fluctuations & Flicker ESD (Electrostatic IEC61000-4-2 6 kV contact discharge, 8 kV air discharge, level 3 Discharge) RF Electromagnetic Field IEC61000-4-3 3 V/m, 80 - 1000 MHz, 80% modulated at a distance of 3 meters Susceptibility IEC61000-4-4 2 kV on AC power port for 1 minute, 1 kV on signal/control lines Electrical Fast Transient 2 kV line to line (differential mode) / 2 kV line to common mode ground Immunity (tested to secondary ground) on AC power port, 0.5 kV for outdoor cables IEC61000-4-5 Compliance Higher surge is available. Please contact your ERP representative or send an Surge email to SaveEnergy@erp-power.com. ANSI/IEEE c62.41.1-2002 & c62.41.2-2002 category A, 2.5 kV ring wave Conducted RF IEC61000-4-6 3V, 0.15-80 MHz, 80% modulated Disturbances IEC61000-4-11 >95% dip, 0.5 period; 30% dip, 25 periods; 95% reduction, 250 periods Voltage Dips Hi Pot (High Potential) or Dielectric voltage-withstand SaveEnergy@erp-power.com Units Minimum Vdc 2500 Safety Typical 5 Maximum Notes Insulation between the input (AC line and Neutral) and the output Tested at the RMS voltage equivalent of 1767 Vac www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 7 - PROTECTION FEATURES ina ry In fo rm Short Circuit and Over Current Protection The PSB50/40/30 series is protected against short-circuit such that a short from any output to return shall not result in a fire hazard or shock hazard. The driver shall hiccup as a result of a short circuit or over current fault. Removal of the fault will return the driver to within normal operation. The driver shall recover, with no damage, from a short across the output for an indefinite period of time. Internal Over temperature Protection The PSB50/40/30 series is equipped with internal temperature sensor on the primary power train. Failure to stay within the convection power rating will result in the power supply reducing the available current (fold back) below the programmed amount. The main output current will be restored to the programmed value when the temperature of the built-in temperature sensor cools adequately. Output Open Load Protection When the LED load is removed, the output voltage of the PSB50/40/30 series is typically limited to 1.3 times the maximum output voltage of each model. 8 - OUTPUT POWER DE-RATING AT ELEVATED TEMPERATURES The PSB50/40/30 series can be operated with cooling air temperatures above 50C by linearly derating the total maximum output power (or current) by 2.5%/C from 50C to 70C (see figure 2). 110% 100% 80% m Percent of Output Power 90% 70% 60% eli 50% 40% 30% Pr 20% 10% 0% 0 SaveEnergy@erp-power.com 10 20 30 40 50 60 Ambient Temperature (C) 70 80 Figure 2 6 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 9 - PHASE-CUT DIMMING Percent of Output Current (Normalized to Rated Current In fo rm Dimming of the driver is possible with standard TRIAC-based incandescent dimmers that chop the AC voltage as shown in Figure 3, or with ELV dimmers. During the rapid rise time of the AC voltage when the dimmer turns on, the driver does not generate any voltage or current oscillations, and inrush current is controlled. During the ontime of the AC input, the driver regulates the output current based upon the conduction angle. The RMS value of the driver output current is proportional to the on-time of the AC input voltage. When operating with an incandescent dimmer, the RMS output current varies depending upon the conduction angle and RMS value of the applied AC input voltage. Figure 4 shows the typical output current versus conduction angle at nominal input voltage. Forward-phase (TRIAC) and reverse-phase (ELV) dimming work only at 120 Vac. The PSB50/40/30 series offers Tri-Mode DimmingTM compatibility with both phase-cut (reverse-phase and forward-phase) and 0-10V dimmers. Phase-cut dimming always has priority over 0-10 V dimming. AC Wall Power ina ry Chopped AC Input to Driver Output Current versus Conduction Angle Figure 3 Conduction Angle Figure 4 Pr eli m 10 - COMPATIBLE PHASE-CUT DIMMERS & DIMMING RANGE Dimming compatibility charts are available for each model in the PSB50/40/30 series. Please contact your sales representative or send an email to: SaveEnergy@erp-power.com. SaveEnergy@erp-power.com 7 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 11 - 0-10 V DIMMING In fo rm The PSB50/40/30 series operate only with 0-10V dimmers that sink current. They are not designed to operate with 0-10V control systems that source current, as used in theatrical/entertainment systems. Developed in the 1980's, the 0-10V sinking current control method is adopted by the International Electrotechnical Commission (IEC) as part of its IEC Standard 60929 Annex E. The method to dim the output current of the driver is done via the +Dim/-Dim Signal pins. The +Dim/-Dim Signal pins respond to a 0 to 10 V signal, delivering 1% to 100% of the output current based on rated current for each model. A pull-up resistor is included internal to the driver. When the +Dim wire (purple) is short circuited to the -Dim wire (grey) or to the -LED wire (blue), the output current turns off. If the +Dim input is > 10 V or open circuited, the output current is programmed to 100% of the rated current. When not used, the -Dim wire (grey) and to the +Dim wire (purple) can be individually capped or cut off. In this configuration, no dimming is possible and the driver delivers 100% of its rated output current. The maximum source current (flowing from the driver to the 0-10V dimmer) supplied by the +Dim Signal pin is 1 mA. The tolerance of the output current while being dimmed shall be +/-8% typical until down to 1.5 V. ina ry The non-linear 0-10V dimming profile is the default profile across all models of the PSB50/40/30 series. In the nonlinear 0-10V dimming profile, shown in figure 5, 10V to 9.1V=100% of the output current, 1.5V to 0.6V=1%, <0.6V=dim-to-off (no output current). The non-linear curve is recommended when using standard in wall 0-10 V logarithmic dimmers to avoid having insufficient source current available to pull the dimmer up to 10V and to account for the inability of the dimmer to pull below approximately 0.9V. In these type of installations, the modified transfer function will ensure 100% light output and dimming to 1%, regardless of the number of drivers on the 0-10V dimming line. Please contact your sales representative or send an email to: SaveEnergy@erp-power.com for additional information. m eli Percent of Output Current (Normalized to Rated Current) 100% Dimming Voltage Description Value C hysteresis > 700 mV, < 800 mV 1% Pr 0% 0.6 C 1.5 Dimming Voltage (V) 12 - COMPATIBLE 0-10 V DIMMERS * Lutron, Nova series (part number NFTV) * Lutron, Diva series (part number DVTV) * Leviton, IllumaTech series (part number IP710-DL) SaveEnergy@erp-power.com 8 9.1 10 (V) Figure 5 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 13 - PROGRAMMING In fo rm The PSB50/40/30 series can be programmed by inserting the audio jack of the cable shown in figure 6 into the driver and by plugging the USB other end of the cable into a computer. The driver does not need to be powered on during the programming process. When ordering the PSB50/40/30 series, please make sure you order a programming cable. The part number for the programming cable is "PROG-JACK-USB". Programming is done by using the ERP GUI (Graphical User Interface) which enables to trim or adjust output current from 100% to 50%. Figure 6 Pr eli m ina ry Furthermore, when connecting the driver to a computer using the programming cable, you can access the driver's internal data log and read the following information: SKU, serial number, manufacturing lot code, hours of operation, firmware revision, and fault events: power failure, transients (short or surge), thermal events (i.e. number of times the case temperature has exceed the maximum case temperature of 90C). For more information, please refer to the GUI user's manual. SaveEnergy@erp-power.com 9 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 14 - MECHANICAL DETAILS Aluminum case Flying leads, 18 AWG on power leads, 22 AWG on 0-10V dimming wires and on auxiliary output, 203mm (8 in) long, 105C rated, stranded, stripped by approximately 9.5mm, and tinned. All the wires, on both input and output, have a 600 V insulation rating. Ingress Protection: IP20 rated Mounting Instructions: The PSB50/40/30 driver case must be secured on a flat surface through the two mounting tabs, shown here below in the case outline drawings. 15 - OUTLINE DRAWINGS In fo rm Packaging Options: I/O Connections: Pr eli m ina ry Dimensions: L 98.5 * W 25.4 * H 19.05 mm (L 3.88 * W 1.00 * H 0.75 in.) Volume: 46.9 cm3 (2.87 in3) Weight: SaveEnergy@erp-power.com All dimensions are in mm Figure 7 10 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) 16 - LABELING In fo rm The PSB50-1200-42 is used in figure 8 as an example to illustrate a typical label. m ina ry Figure 8 CHINA Operations Tel: +86-756-6266298 Fax: +86-756-6266299 No. 8 Pingdong Road 2 Zhuhai, Guangdong, China 519060 eli USA Headquarters Tel: +1-805-517-1300 Fax: +1-805-517-1411 893 Patriot Drive, Suite E, Moorpark, CA 93021, USA Pr ERP Power, LLC (ERP) reserves the right to make changes without further notice to any products herein. ERP makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ERP assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in ERP data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ERP does not convey any license under its patent rights nor the rights of others. ERP products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the ERP product could create a situation where personal injury or death may occur. Should Buyer purchase or use ERP products for any such unintended or unauthorized application, Buyer shall indemnify and hold ERP and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ERP was negligent regarding the design or manufacture of the part. ERP is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. SaveEnergy@erp-power.com 11 www.erp-power.com PSB50 PSB40 PSB30 50 W 40 W 30 W at ion PSB50/40/30 Series In fo rm 50, 40 & 30 W Programmable Constant Current LED Driver with Tri-Mode DimmingTM (TRIAC, ELV & 0-10 V) Revision History Revision Date Originator Comments Prelim. 15OCT2017 LJ Created data sheet Prelim. 02NOV2017 LJ * * * * Prelim. 05NOV2017 LJ * Updated list of applications Prelim. 06NOV2017 LJ * Updated acoustic noise specification Prelim. 14NOV2017 LJ * Extended Vout range on all models Prelim. 25NOV2017 LJ * Combined the 2 Surge specs in section 6 Prelim. 04DEC2017 LJ * Corrected the part number of the programming cable to "PROG-JACK-USB" Pr eli m ina ry Updated feature table on front page. Updated Lifetime: 50,000 hours @ Tc = 75C Updated part numbers in section 1 and added nominal values Updated package dimensions and mechanical outline dimensions in section 15 * Added a comment about the programming cable in section 1 * Updated the 0-10V dimming profile in section 4 & 11 * Updated Safety agency approvals in section 6 (c) ERP Power, LLC 12 PSB50/40/30 Series Data Sheet - Preliminary Information Rev. December 2017