8700 E. Thomas Road Scottsdale, AZ 85251 Tel: (480) 941-6300 Fax: (480) 947-1503 FLIP-CHIP TVS DIODES CHFP6KE5.0 thru CHFP6KE170CA Patented Flip-Chip Series FEATURES * * * * * * Unidirectional and Bidirectional Fully glass passivated 600 watt (10/1000 s) Eliminates wire bonding NON Inductive Insertion No voltage overshoot MAXIMUM RATINGS * * * * * MECHANICAL * Weight: 0.01 grams (approximate) * Solderable standoff tabs .040X.040X.010 PACKAGING * * * Max Junction Temperature: 1500C (with conformal coating) Storage Temperature: -550C to +1500C Flip-Chip Peak Pulse Power: 600 Watts (10/1000 s) Maximum non-repetitive peak power 600 Watts (10/1000 s) Total continuous power dissipation 2.5 W (with adequate heat sink @ 750C) Turn-on time (theoretical) unidirectional 1X10-12 Turn-on time (theoretical) bidirectional 1X10-9 Waffle package 50 pices or wafer ring 70 pieces BIDIRECTIONAL ALL DIMENSIONS NOMINAL inches (mm) FLIP-CHIP DIMENSIONS PAD SIZE & CIRCUIT UNIDIRECTIONAL ALL DIMENSIONS NOMINAL inches (mm) FLIP-CHIP DIMENSIONS PAD SIZE & CIRCUIT VBR above 30 V MSC1596.PDF ISO 9001 CERTIFIED VBR 30V and below REV B 3/13/2000 CHFP6KE5.0 thru CHFP6KE170CA PEAK PULSE POWER DERATING Peak Pulse Power (PPP) or Current (IPP) In percent of 25 C rating Ppp - PEAK PULSE POWER - kW PEAK PULSE POWER Vs PULSE TIME TP - PULSE TIME - SEC TEMPERATURE C ATTACHMENT AND CONFORMAL COATING INSTRUCTIONS FOR Flip-Chip COMPONENTS The .010" thick tab standoffs minimize shorting during attachment; however, minimal solder/conductive epoxy must be used and carefully controlled to prevent excess attachment material from wicking up the side of the tab and shorting across the junction. Maximum recommended solder temperatures are 212 C for IR reflow and 221 C for vapor-phase reflow. For flip-chip protection, coating material is Stycast TM 2651-40 lowviscosity epoxy manufactured by Emerson & Cuming. Follow instructions carefully for preparation of the epoxy to prevent entrapment of air bubbles. Make sure that Flip-Chips have been baked at 100 C for 15 minutes minimum to out-gas any adsorbed moisture immediately prior to coating. Epoxy-coating material should be dispensed around the edges of the chip with an appropriately sized syringe after which epoxy is de-aired to remove bubbles entrapped beneath the chip. Cure epoxy as instructed by the supplier. MSC1596.PDF ISO 9001 CERTIFIED REV B 3/13/2000 CHFP6KE5.0 thru CHFP6KE170CA 0 ELECTRICAL Characteristics @ 25 C Unless otherwise specified Part Number Rated Stand-off Voltage VWM Minimum Breakdown Voltage V(BR) @I T Maximum Clamping @ IPP VC Max Maximum Reverse Leakage @ VWM ID Rated Maximum Peak Pulse Current I PP Maximum Voltage Temperature Coefficient OF V(BR) VOLTS VOLTS mA VOLTS A AMPS %/C CHFP6KE5.0 5.0 6.4 10 9.6 800 62.5 .057 CHFP6KE5.0A 5.0 6.4 10 9.2 800 62.5 .057 CHFP6KE6.0 6.0 6.67 10 11.4 800 52.6 .059 CHFP6KE6.0A 6.0 6.67 10 10.3 800 58.3 .059 CHFP6KE6.5 6.5 7.22 10 12.3 500 48.7 .061 CHFP6KE6.5A 6.5 7.22 10 11.2 500 53.6 .061 CHFP6KE7.0 7.0 7.78 10 13.3 200 45.1 .065 CHFP6KE7.0A 7.0 7.78 10 12.0 200 50.0 .065 CHFP6KE7.5 7.5 8.33 1 14.3 100 42.0 .067 CHFP6KE7.5A 7.5 8.33 1 12.9 100 46.5 .067 CHFP6KE8.0 8.0 8.89 1 15.0 50 40.0 .070 CHFP6KE8.0A 8.0 8.89 1 13.6 50 44.1 .070 CHFP6KE8.5 8.5 9.44 1 15.9 10 CHFP6KE8.5A 8.5 9.44 1 14.4 10 41.7 .073 CHFP6KE9.0 9.0 10.0 1 16.9 5 35.5 .076 CHFP6KE9.0A 9.0 10.0 1 15.4 5 59.0 .076 CHFP6KE10 10 11.1 1 18.8 5 31.9 .078 CHFP6KE10A 10 11.1 1 17.0 5 35.3 .078 CHFP6KE11 11 12.2 1 20.1 5 29.9 .081 CHFP6KE11A 11 12.2 1 18.2 5 33.0 .081 CHFP6KE12 12 13.3 1 22.0 5 27.3 .082 CHFP6KE12A 12 13.3 1 19.9 5 30.2 .082 CHFP6KE13 13 14.4 1 23.8 5 25.2 .084 CHFP6KE13A 13 14.4 1 21.5 5 27.9 .084 CHFP6KE14 14 15.6 1 25.8 5 23.3 .086 CHFP6KE14A 14 15.6 1 23.2 5 25.8 .086 CHFP6KE15 15 16.7 1 26.9 5 22.3 .087 CHFP6KE15A 15 16.7 1 24.4 5 24.0 .087 CHFP6KE16 16 17.8 1 28.8 5 20.8 .088 CHFP6KE16A 16 17.8 1 26.0 5 23.1 .088 CHFP6KE17 17 18.9 1 30.5 5 29.7 .090 CHFP6KE17A 17 18.9 1 27.6 5 21.7 .090 CHFP6KE18 18 20.0 1 32.2 5 18.6 .092 CHFP6KE18A 18 20.0 1 29.2 5 20.5 .092 CHFP6KE20 20 22.2 1 35.8 5 16.7 .093 CHFP6KE20A 20 22.2 1 32.4 5 18.5 .093 CHFP6KE22 22 24.4 1 39.4 5 15.2 .094 CHFP6KE22A 22 24.4 1 35.5 5 16.9 .094 CHFP6KE24 24 26.7 1 43.0 5 14.0 .096 CHFP6KE24A 24 26.7 1 38.9 5 15.4 .096 CHFP6KE26 26 28.9 1 46.6 5 12.4 .097 CHFP6KE26A 26 28.9 1 42.1 5 14.2 .097 CHFP6KE28 28 31.1 1 50.0 5 12.0 .098 CHFP6KE28A 28 31.1 1 45.4 5 13.2 .098 CHFP6KE30 30 33.3 1 53.5 5 11.2 .099 CHFP6KE30A 30 33.3 1 48.4 5 12.4 .099 CHFP6KE33 33 36.7 1 59.0 5 10.2 .100 CHFP6KE33A 33 36.7 1 53.3 5 11.3 .100 CHFP6KE36 36 40.0 1 64.3 5 9.3 .101 CHFP6KE36A 36 40.0 1 58.1 5 10.3 .101 CHFP6KE40 40 44.4 1 71.4 5 8.4 .101 CHFP6KE40A 40 44.4 1 64.5 5 9.3 .101 CHFP6KE43 43 47.8 1 76.7 5 7.8 .102 CHFP6KE43A 43 47.8 1 69.4 5 8.6 .102 CHFP6KE45 45 50.0 1 80.3 5 7.5 .102 CHFP6KE45A 45 50.0 1 72.7 5 8.3 .102 CHFP6KE48 48 53.3 1 85.5 5 7.0 .103 CHFP6KE48A 48 53.3 1 77.4 5 7.7 .103 CHFP6KE51 51 56.7 1 91.1 5 6.6 .103 CHFP6KE51A 51 56.7 1 82.4 5 7.3 .103 CHFP6KE54 54 60.0 1 96.3 5 6.2 .104 CHFP6KE54A 54 60.0 1 87.1 5 6.9 .104 CHFP6KE58 58 64.4 1 103 5 5.8 .104 CHFP6KE58A 58 64.4 1 93.6 5 6.4 .104 CHFP6KE60 60 66.7 1 107 5 5.6 .104 CHFP6KE60A 60 66.7 1 96.8 5 6.2 .104 CHFP6KE64 64 71.1 1 114 5 5.3 .105 CHFP6KE64A 64 71.1 1 103 5 5.8 .105 CHFP6KE70 70 77.8 1 125 5 4.8 .105 CHFP6KE70A 70 77.8 1 113 5 5.3 .105 CHFP6KE75 75 83.3 1 134 5 4.5 .105 CHFP6KE75A 75 83.3 1 121 5 4.9 .105 CHFP6KE78 78 86.7 1 139 5 4.3 .106 CHFP6KE78A 78 86.7 1 126 5 4.7 .106 CHFP6KE85 85 94.4 1 151 5 3.9 .107 CHFP6KE85A 85 94.4 1 137 5 4.4 .107 CHFP6KE90 90 100 1 160 5 3.8 .107 37.7 .073 CHFP6KE90A 90 100 1 146 5 4.1 .107 CHFP6KE100 100 111 1 179 5 3.4 .107 CHFP6KE100A 100 111 1 162 5 3.7 .107 CHFP6KE110 110 122 1 196 5 3.0 .108 CHFP6KE110A 110 122 1 177 5 3.4 .108 CHFP6KE120 120 133 1 214 5 2.8 .108 CHFP6KE120A 120 133 1 193 5 3.1 .108 CHFP6KE130 130 144 1 231 5 2.6 .108 CHFP6KE130A 130 144 1 209 5 2.9 .108 CHFP6KE150 150 167 1 268 5 2.2 .108 CHFP6KE150A 150 167 1 243 5 2.5 .108 CHFP6KE160 160 178 1 287 5 2.1 .108 CHFP6KE160A 160 178 1 259 5 2.3 .108 CHFP6KE170 170 189 1 304 5 2.0 .108 MSC1596.PDF ISO 9001 CERTIFIED Note: For bidirectional devices add a "C" (example CHFP6KE5.0C thru CHFP6KE170CA are bidirectional devices). TOLERANCES A suffix designates 5% Plain suffix designates 10% REV B 3/13/2000