FLASH MEMORY
1
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
K9XXG08XXB
* Samsung Electronics reserves the right to change products or specification without notice.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE,
TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOLOGY. ALL
INFORMATION IN THIS DOCUMENT IS PROVIDED
ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar
applications where Product failure could result in loss of life or personal or physical harm, or any military or
defense application, or any governmental procurement to which special terms or provisions may apply.
FLASH MEMORY
2
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Document Title
512M x 8 Bit / 1G x 8 Bit NAND Flash Memory
Revision History
The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right
to change the specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions about device. If you have
any questions, please contact the SAMSUNG branch office near your office.
Revision No
0.0
0.1
0.2
Remark
Advance
Advance
Advance
History
1. Initial issue
1. The timing of 2-Plane copy-back program is changed.
1. 1bit/512byte ECC -> 1bit/528byte ECC
Draft Date
Mar. 17th 2008
Apr. 7th 2008
May 30, 2008
FLASH MEMORY
3
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
GENERAL DESCRIPTION
FEATURES
Voltage Supply
- 2.7V Device(K9F4G08B0B) : 2.5V ~ 2.9V
- 3.3V Device(K9F4G08U0B) : 2.7V ~ 3.6V
Organization
- Memory Cell Array : (512M + 16M) x 8bit
- Data Register : (2K + 64) x 8bit
Automatic Program and Erase
- Page Program : (2K + 64)Byte
- Block Erase : (128K + 4K)Byte
Page Read Operation
- Page Size : (2K + 64)Byte
- Random Read : 25µs(Max.)
- Serial Access : 25ns(Min.)
512M x 8 Bit / 1G x 8 Bit NAND Flash Memory
Fast Write Cycle Time
- Page Program time : 200µs(Typ.)
- Block Erase Time : 1.5ms(Typ.)
Command/Address/Data Multiplexed I/O Port
Hardware Data Protection
- Program/Erase Lockout During Power Transitions
Reliable CMOS Floating-Gate Technology
-Endurance : 100K Program/Erase Cycles(with 1bit/528Byte
ECC)
- Data Retention : 10 Years
Command Driven Operation
Unique ID for Copyright Protection
Package :
- K9F4G08B0B-PCB0/PIB0
48 - Pin TSOP I (12 x 20 / 0.5 mm pitch)
- K9F4G08U0B-PCB0/PIB0
48 - Pin TSOP I (12 x 20 / 0.5 mm pitch)
- K9F4G08U0B-ICB0/IIB0
52 - Pin ULGA (12 x 17 / 1.00 mm pitch)
- K9K8G08U1B-ICB0/IIB0
52 - Pin ULGA (12 x 17 / 1.00 mm pitch)
Offered in 512Mx8bit, the K9F4G08X0B is a 4G-bit NAND Flash Memory with spare 128M-bit. The device is offered in 2.7V and 3.3V
Vcc. Its NAND cell provides the most cost-effective solution for the solid state application market. A program operation can be per-
formed in typical 200µs on the (2K+64)Byte page and an erase operation can be performed in typical 1.5ms on a (128K+4K)Byte
block. Data in the data register can be read out at 25ns cycle time per Byte. The I/O pins serve as the ports for address and data
input/output as well as command input. The on-chip write controller automates all program and erase functions including pulse repe-
tition, where required, and internal verification and margining of data. Even the write-intensive systems can take advantage of the
K9F4G08X0Bs extended reliability of 100K program/erase cycles by providing ECC(Error Correcting Code) with real time mapping-
out algorithm. The K9F4G08X0B is an optimum solution for large nonvolatile storage applications such as solid state file storage and
other portable applications requiring non-volatility.
PRODUCT LIST
Part Number Vcc Range Organization PKG Type
K9F4G08B0B-P 2.50 ~ 2.90V
X8
TSOP1
K9F4G08U0B-P
2.70 ~ 3.60V
K9F4G08U0B-I 52ULGA
K9K8G08U1B-I
FLASH MEMORY
4
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
PIN CONFIGURATION (TSOP1)
K9F4G08X0B-PCB0/PIB0
PACKAGE DIMENSIONS
48-PIN LEAD FREE PLASTIC THIN SMALL OUT-LINE PACKAGE TYPE(I)
48 - TSOP1 - 1220F Unit :mm/Inch
0.787±0.008
20.00±0.20
#1
#24
0.20+0.07
-0.03
0.008+0.003
-0.001
0.50
0.0197
#48
#25
0.488
12.40 MAX
12.00
0.472
0.10
0.004 MAX
0.25
0.010
()
0.039±0.002
1.00±0.05
0.002
0.05 MIN
0.047
1.20 MAX
0.45~0.75
0.018~0.030
0.724±0.004
18.40±0.10
0~8°
0.010
0.25 TYP
0.125 +0.075
0.035
0.005+0.003
-0.001
0.50
0.020
()
48-pin TSOP1
Standard Type
12mm x 20mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
N.C
N.C
N.C
N.C
N.C
N.C
R/B
RE
CE
N.C
N.C
Vcc
Vss
N.C
N.C
CLE
ALE
WE
WP
N.C
N.C
N.C
N.C
N.C
N.C
N.C
N.C
N.C
I/O7
I/O6
I/O5
I/O4
N.C
N.C
N.C
Vcc
Vss
N.C
N.C
N.C
I/O3
I/O2
I/O1
I/O0
N.C
N.C
N.C
N.C
FLASH MEMORY
5
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
1.00
1.00
1.00
1.00
2.00
7 6 5 4 3 2 1
1.00
1.00
1.00
12.00±0.10
#A1
17.00±0.10
17.00±0.10
B
A
12.00±0.10
(Datum B)
(Datum A)
12.00
10.00
2.50
2.50
2.00
0.50 1.30
A
B
C
D
E
F
G
H
J
K
L
M
N
12-
1.00
±
0.05
41-
0.70
±
0.05
Side View
0.65
(
Max
.)
0.10 C
17.00
±
0.10
Top View Bottom View
AB CDEFGHJKLMN
7
6
5
4
3
2
1
PIN CONFIGURATION (ULGA)
K9F4G08U0B-ICB0/IIB0
52-ULGA (measured in millimeters)
NC NC NC NC
NC
NC
NC NC NC
NC
NC
NC
NC
NC
NC
NC
Vcc
Vcc
Vss
Vss
Vss
/RE
NC
/CE NC
CLE NC
ALE
NC
/WE
NC
/WP
NC
R/B
NC
Vss
IO0
NC
IO1
NC
IO2
IO3
NC
NC
IO4 NC
IO5
NC
IO6
NC
IO7
NC
ABCM
0.1
ABCM
0.1
PACKAGE DIMENSIONS
FLASH MEMORY
6
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
1.00
1.00
1.00
1.00
2.00
7 6 5 4 3 2 1
1.00
1.00
1.00
12.00±0.10
#A1
17.00±0.10
17.00±0.10
B
A
12.00±0.10
(Datum B)
(Datum A)
12.00
10.00
2.50
2.50
2.00
0.50 1.30
A
B
C
D
E
F
G
H
J
K
L
M
N
12-
1.00
±
0.05
41-
0.70
±
0.05
Side View
0.65
(
Max
.)
0.10 C
17.00
±
0.10
Top View Bottom View
AB CDEFGHJKLMN
7
6
5
4
3
2
1
K9K8G08U1B-ICB0/IIB0
52-ULGA (measured in millimeters)
NC NC NC NC
NC
NC
NC NC NC
NC
NC
NC
NC
NC
NC
NC
Vcc
Vcc
Vss
Vss
Vss
/RE1
/RE2
/CE1 /CE2
CLE1 CLE2
ALE1
ALE2
/WE1
/WE2
/WP1
/WP2
R/B1
R/B2
Vss
IO0-1
IO0-2
IO1-1
IO1-2
IO2-1
IO3-1
IO2-2
IO3-2
IO4-1 IO4-2
IO5-1
IO5-2
IO6-1
IO6-2
IO7-1
IO7-2
ABCM
0.1
ABCM
0.1
PACKAGE DIMENSIONS
FLASH MEMORY
7
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
PIN DESCRIPTION
NOTE : Connect all VCC and VSS pins of each device to common power supply outputs.
Do not leave VCC or VSS disconnected.
Pin Name Pin Function
I/O0 ~ I/O7
DATA INPUTS/OUTPUTS
The I/O pins are used to input command, address and data, and to output data during read operations. The I/
O pins float to high-z when the chip is deselected or when the outputs are disabled.
CLE
COMMAND LATCH ENABLE
The CLE input controls the activating path for commands sent to the command register. When active high,
commands are latched into the command register through the I/O ports on the rising edge of the WE signal.
ALE
ADDRESS LATCH ENABLE
The ALE input controls the activating path for address to the internal address registers. Addresses are
latched on the rising edge of WE with ALE high.
CE
CHIP ENABLE
The CE input is the device selection control. When the device is in the Busy state, CE high is ignored, and
the device does not return to standby mode in program or erase operation.
RE
READ ENABLE
The RE input is the serial data-out control, and when active drives the data onto the I/O bus. Data is valid
tREA after the falling edge of RE which also increments the internal column address counter by one.
WE
WRITE ENABLE
The WE input controls writes to the I/O port. Commands, address and data are latched on the rising edge of
the WE pulse.
WP
WRITE PROTECT
The WP pin provides inadvertent program/erase protection during power transitions. The internal high volt-
age generator is reset when the WP pin is active low.
R/B
READY/BUSY OUTPUT
The R/B output indicates the status of the device operation. When low, it indicates that a program, erase or
random read operation is in process and returns to high state upon completion. It is an open drain output and
does not float to high-z condition when the chip is deselected or when outputs are disabled.
Vcc POWER
VCC is the power supply for device.
Vss GROUND
N.C NO CONNECTION
Lead is not internally connected.
FLASH MEMORY
8
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
2K Bytes 64 Bytes
Figure 1. K9F4G08X0B Functional Block Diagram
Figure 2. K9F4G08X0B Array Organization
NOTE : Column Address : Starting Address of the Register.
* L must be set to "Low".
* The device ignores any additional input of address cycles than required.
I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7
1st Cycle A0A1A2A3A4A5A6A7
2nd Cycle A8A9A10 A11 *L *L *L *L
3rd Cycle A12 A13 A14 A15 A16 A17 A18 A19
4th Cycle A20 A21 A22 A23 A24 A25 A26 A27
5th Cycle A28 A29 *L *L *L *L *L *L
VCC
X-Buffers
Command
I/O Buffers & Latches
Latches
& Decoders
Y-Buffers
Latches
& Decoders
Register
Control Logic
& High Voltage
Generator Global Buffers Output
Driver
VSS
A12 - A29
A0 - A11
Command
CE
RE
WE
CLE WP
I/0 0
I/0 7
VCC
VSS
256K Pages
(=4,096 Blocks)
2K Bytes
8 bit
64 Bytes
1 Block = 64 Pages
(128K + 4K) Byte
I/O 0 ~ I/O 7
1 Page = (2K + 64)Bytes
1 Block = (2K + 64)B x 64 Pages
= (128K + 4K) Bytes
1 Device = (2K+64)B x 64Pages x 4,096 Blocks
= 4,224 Mbits
Row Address
Page Register
ALE
4,096M + 128M Bit
NAND Flash
ARRAY
(2,048 + 64)Byte x 262,144
Y-Gating
Row Address
Column Address
Column Address
Row Address
Data Register & S/A
FLASH MEMORY
9
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Product Introduction
The K9F4G08X0B is a 4,224Mbit(4,429,185,024 bit) memory organized as 262,144 rows(pages) by 2,112x8 columns. Spare 64x8
columns are located from column address of 2,048~2,111. A 2,112-byte data register is connected to memory cell arrays accommo-
dating data transfer between the I/O buffers and memory during page read and page program operations. The memory array is made
up of 32 cells that are serially connected to form a NAND structure. Each of the 32 cells resides in a different page. A block consists
of two NAND structured strings. A NAND structure consists of 32 cells. Total 1,081,344 NAND cells reside in a block. The program
and read operations are executed on a page basis, while the erase operation is executed on a block basis. The memory array con-
sists of 4,096 separately erasable 128K-byte blocks. It indicates that the bit by bit erase operation is prohibited on the K9F4G08X0B.
The K9F4G08X0B has addresses multiplexed into 8 I/Os. This scheme dramatically reduces pin counts and allows system upgrades
to future densities by maintaining consistency in system board design. Command, address and data are all written through I/O's by
bringing WE to low while CE is low. Those are latched on the rising edge of WE. Command Latch Enable(CLE) and Address Latch
Enable(ALE) are used to multiplex command and address respectively, via the I/O pins. Some commands require one bus cycle. For
example, Reset Command, Status Read Command, etc require just one cycle bus. Some other commands, like page read and block
erase and page program, require two cycles: one cycle for setup and the other cycle for execution. The 528M byte physical space
requires 30 addresses, thereby requiring five cycles for addressing : 2 cycles of column address, 3 cycles of row address, in that
order. Page Read and Page Program need the same five address cycles following the required command input. In Block Erase oper-
ation, however, only the three row address cycles are used. Device operations are selected by writing specific commands into the
command register. Table 1 defines the specific commands of the K9F4G08X0B.
In addition to the enhanced architecture and interface, the device incorporates copy-back program feature from one page to another
page without need for transporting the data to and from the external buffer memory. Since the time-consuming serial access and
data-input cycles are removed, system performance for solid-state disk application is significantly increased.
Table 1. Command Sets
NOTE : 1. Random Data Input/Output can be executed in a page.
2. Any command between 11h and 81h is prohibited except 70h/F1h and FFh.
Caution : Any undefined command inputs are prohibited except for above command set of Table 1.
Function 1st Cycle 2nd Cycle Acceptable Command during Busy
Read 00h 30h
Read for Copy Back 00h 35h
Read ID 90h -
Reset FFh - O
Page Program 80h 10h
Two-Plane Page Program(2) 80h---11h 81h---10h
Copy-Back Program 85h 10h
Two-Plane Copy-Back Program(2) 85h---11h 81h---10h
Block Erase 60h D0h
Two-Plane Block Erase 60h---60h D0h
Random Data Input(1) 85h -
Random Data Output(1) 05h E0h
Read Status 70h O
Read Status 2 F1h O
FLASH MEMORY
10
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
ABSOLUTE MAXIMUM RATINGS
NOTE :
1. Minimum DC voltage is -0.6V on input/output pins. During transitions, this level may undershoot to -2.0V for periods <30ns.
Maximum DC voltage on input/output pins is VCC+0.3V which, during transitions, may overshoot to VCC+2.0V for periods <20ns.
2. Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to the conditions
as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Parameter Symbol Rating Unit
Voltage on any pin relative to VSS
VCC -0.6 to +4.6
V
VIN -0.6 to +4.6
VI/O -0.6 to Vcc + 0.3 (< 4.6V)
Temperature Under Bias K9XXG08XXB-XCB0 TBIAS
-10 to +125 °C
K9XXG08XXB-XIB0 -40 to +125
Storage Temperature K9XXG08XXB-XCB0 TSTG -65 to +150 °C
K9XXG08XXB-XIB0
Short Circuit Current IOS 5mA
RECOMMENDED OPERATING CONDITIONS
(Voltage reference to GND, K9XXG08XXB-XCB0 :TA=0 to 70°C, K9XXG08XXB-XIB0:TA=-40 to 85°C)
Parameter Symbol K9F4G08B0B(2.7V) K9F4G08U0B(3.3V) Unit
Min Typ. Max Min Typ. Max
Supply Voltage VCC 2.5 2.7 2.9 2.7 3.3 3.6 V
Supply Voltage VSS 000000 V
DC AND OPERATING CHARACTERISTICS(Recommended operating conditions otherwise noted.)
NOTE :
1. VIL can undershoot to -0.4V and VIH can overshoot to VCC + 0.4V for durations of 20 ns or less.
2. Typical value is measured at Vcc=2.7V/3.3V, TA=25°C. Not 100% tested.
3. The typical value of the K9K8G08U1B’s ISB2 is 20µA and the maximum value is 100µA.
Parameter Symbol Test Conditions
K9F4G08X0B
Unit2.7V 3.3V
Min Typ Max Min Typ Max
Operating
Current
Page Read with
Serial Access ICC1tRC=50ns, CE=VIL
IOUT=0mA - 15 30 - 15 30
mA
Program ICC2 - - 15 30 - 15 30
Erase ICC3 - - 15 30 - 15 30
Stand-by Current(TTL) ISB1CE=VIH, WP=PRE=0V/VCC --1--1
Stand-by Current(CMOS) ISB2CE=VCC-0.2,
WP=PRE=0V/VCC - 10 50 - 10 50
µA
Input Leakage Current ILI VIN=0 to Vcc(max) - - ±10 - - ±10
Output Leakage Current ILO VOUT=0 to Vcc(max) - - ±10 - - ±10
Input High Voltage VIH* -VCC
-0.4 -VCC
+0.3 2.0 - VCC
+0.3
V
Input Low Voltage, All inputs VIL* - -0.3 - 0.5 -0.3 - 0.8
Output High Voltage Level VOH K9G4G08B0B :IOH=-100µA
K9G4G08U0B :IOH=-400µA
VCC
-0.4 --2.4--
Output Low Voltage Level VOL K9G4G08B0B :IOL=100uA
K9G4G08U0B :IOL=2.1mA --0.4--0.4
Output Low Current(R/B)IOL(R/B)K9G4G08B0B :VOL=0.1V
K9G4G08U0B :VOL=0.4V 34- 810-mA
FLASH MEMORY
11
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
VALID BLOCK
NOTE :
1. The device may include initial invalid blocks when first shipped. Additional invalid blocks may develop while being used. The number of valid blocks is
presented with both cases of invalid blocks considered. Invalid blocks are defined as blocks that contain one or more bad bits. Do not erase or pro-
gram factory-marked bad blocks. Refer to the attached technical notes for appropriate management of invalid blocks.
2. The 1st block, which is placed on 00h block address, is guaranteed to be a valid block up to 1K program/erase cycles with 1bit/512Byte ECC.
3. The number of valid block is on the basis of single plane operations, and this may be decreased with two plane operations.
* : Each K9F4G08U0B chip in the K9K8G08U1B has Maximun 80 invalid blocks.
Parameter Symbol Min Typ. Max Unit
K9F4G08X0B NVB 4,016 - 4,096 Blocks
K9K8G08U1B NVB 8,032* - 8,192* Blocks
AC TEST CONDITION
(K9XXG08UXB-XCB0 :TA=0 to 70°C, K9F4G08UXB-XIB0:TA=-40 to 85°C, K9XXG08UXB: Vcc=2.7V~3.6V unless otherwise noted)
Parameter K9XXG08UXB
Input Pulse Levels 0V to Vcc
Input Rise and Fall Times 5ns
Input and Output Timing Levels Vcc/2
Output Load 1 TTL GATE and CL=50pF
MODE SELECTION
NOTE : 1. X can be VIL or VIH.
2. WP should be biased to CMOS high or CMOS low for standby.
CLE ALE CE WE RE WP Mode
HLL HX
Read Mode Command Input
L H L H X Address Input(5clock)
HLL HH
Write Mode Command Input
L H L H H Address Input(5clock)
L L L H H Data Input
L L L H X Data Output
X X X X H X During Read(Busy)
XXXXXH During Program(Busy)
XXXXXH During Erase(Busy)
XX(1) X X X L Write Protect
XXHXX
0V/VCC(2) Stand-by
CAPACITANCE(TA=25°C, VCC=2.7V/3.3V, f=1.0MHz)
NOTE : 1. Capacitance is periodically sampled and not 100% tested.
2. CI/O(W)* and CIN(W)* are tested at wafer level.
Item Symbol Test Condition Min Max Unit
Input/Output Capacitance CI/O VIL=0V - 8 pF
CI/O(W)* VIL=0V - 5 pF
Input Capacitance CIN VIN=0V - 8 pF
CIN(W)* VIN=0V - 5 pF
FLASH MEMORY
12
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
AC Timing Characteristics for Command / Address / Data Input
NOTES : 1. The transition of the corresponding control pins must occur only once while WE is held low
2. tADL is the time from the WE rising edge of final address cycle to the WE rising edge of first data cycle
Parameter Symbol Min Max Unit
CLE Setup Time tCLS(1) 12 - ns
CLE Hold Time tCLH 5-ns
CE Setup Time tCS(1) 20 - ns
CE Hold Time tCH 5-ns
WE Pulse Width tWP 12 - ns
ALE Setup Time tALS(1) 12 - ns
ALE Hold Time tALH 5-
ns
Data Setup Time tDS(1) 12 - ns
Data Hold Time tDH 5-ns
Write Cycle Time tWC 25 - ns
WE High Hold Time tWH 10 - ns
Address to Data Loading Time tADL(2) 70 - ns
Program / Erase Characteristics
NOTE : 1. Typical value is measured at Vcc=3.3V, TA=25°C. Not 100% tested.
2. Typical program time is defined as the time within which more than 50% of the whole pages are programmed at 3.3V Vcc and 25°C temperature.
Parameter Symbol Min Typ Max Unit
Program Time tPROG - 200 700 µs
Dummy Busy Time for Two-Plane Page Program tDBSY -0.51 µs
Number of Partial Program Cycles Nop - - 4 cycles
Block Erase Time tBERS -1.510ms
FLASH MEMORY
13
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
AC Characteristics for Operation
NOTE: 1. If reset command(FFh) is written at Ready state, the device goes into Busy for maximum 5µs.
Parameter Symbol Min Max Unit
Data Transfer from Cell to Register tR-25µs
ALE to RE Delay tAR 10 - ns
CLE to RE Delay tCLR 10 - ns
Ready to RE Low tRR 20 - ns
RE Pulse Width tRP 12 - ns
WE High to Busy tWB - 100 ns
Read Cycle Time tRC 25 - ns
RE Access Time tREA -20ns
CE Access Time tCEA -25ns
RE High to Output Hi-Z tRHZ - 100 ns
CE High to Output Hi-Z tCHZ -30ns
RE High to Output Hold tRHOH 15 - ns
RE Low to Output Hold tRLOH 5-
ns
CE High to Output Hold tCOH 15 - ns
RE High Hold Time tREH 10 - ns
Output Hi-Z to RE Low tIR 0-ns
RE High to WE Low tRHW 100 - ns
WE High to RE Low tWHR 60 - ns
Device Resetting Time(Read/Program/Erase) tRST -5/10/500(1) µs
FLASH MEMORY
14
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
NAND Flash Technical Notes
Identifying Initial Invalid Block(s)
Initial Invalid Block(s)
Initial invalid blocks are defined as blocks that contain one or more initial invalid bits whose reliability is not guaranteed by Samsung.
The information regarding the initial invalid block(s) is called the initial invalid block information. Devices with initial invalid block(s)
have the same quality level as devices with all valid blocks and have the same AC and DC characteristics. An initial invalid block(s)
does not affect the performance of valid block(s) because it is isolated from the bit line and the common source line by a select tran-
sistor. The system design must be able to mask out the initial invalid block(s) via address mapping. The 1st block, which is placed on
00h block address, is guaranteed to be a valid block up to 1K program/erase cycles with 1bit/512Byte ECC.
All device locations are erased(FFh) except locations where the initial invalid block(s) information is written prior to shipping. The ini-
tial invalid block(s) status is defined by the 1st byte in the spare area. Samsung makes sure that either the 1st or 2nd page of every
initial invalid block has non-FFh data at the column address of 2048. Since the initial invalid block information is also erasable in
most cases, it is impossible to recover the information once it has been erased. Therefore, the system must be able to recognize the
initial invalid block(s) based on the original initial invalid block information and create the initial invalid block table via the following
suggested flow chart(Figure 3). Any intentional erasure of the original initial invalid block information is prohibited.
*Check "FFh" at the column address 2048
Figure 3. Flow chart to create initial invalid block table
Start
Set Block Address = 0
Check "FFh"
Increment Block Address
Last Block ?
End
No
Yes
Yes
Create (or update) No
Initial
of the 1st and 2nd page in the block
Invalid Block(s) Table
FLASH MEMORY
15
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
NAND Flash Technical Notes (Continued)
Program Flow Chart
Start
I/O 6 = 1 ?
I/O 0 = 0 ?
No
*
Write 80h
Write Address
Write Data
Write 10h
Read Status Register
Program Completed
or R/B = 1 ?
Program Error
Yes
No
Yes
: If program operation results in an error, map out
the block including the page in error and copy the
target data to another block.
*
Error in write or read operation
Within its life time, additional invalid blocks may develop with NAND Flash memory. Refer to the qualification report for the actual
data.The following possible failure modes should be considered to implement a highly reliable system. In the case of status read fail-
ure after erase or program, block replacement should be done. Because program status fail during a page program does not affect
the data of the other pages in the same block, block replacement can be executed with a page-sized buffer by finding an erased
empty block and reprogramming the current target data and copying the rest of the replaced block. In case of Read, ECC must be
employed. To improve the efficiency of memory space, it is recommended that the read or verification failure due to single bit error be
reclaimed by ECC without any block replacement. The said additional block failure rate does not include those reclaimed blocks.
Failure Mode Detection and Countermeasure sequence
Write Erase Failure Status Read after Erase --> Block Replacement
Program Failure Status Read after Program --> Block Replacement
Read Single Bit Failure Verify ECC -> ECC Correction
ECC : Error Correcting Code --> Hamming Code etc.
Example) 1bit correction & 2bit detection
FLASH MEMORY
16
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Erase Flow Chart
Start
I/O 6 = 1 ?
I/O 0 = 0 ?
No
*
Write 60h
Write Block Address
Write D0h
Read Status Register
or R/B = 1 ?
Erase Error
Yes
No
: If erase operation results in an error, map out
the failing block and replace it with another block.
*
Erase Completed
Yes
Read Flow Chart
Start
Verify ECC
No
Write 00h
Write Address
Read Data
ECC Generation
Reclaim the Error
Page Read Completed
Yes
NAND Flash Technical Notes (Continued)
Write 30h
Block Replacement
* Step1
When an error happens in the nth page of the Block ’A’ during erase or program operation.
* Step2
Copy the data in the 1st ~ (n-1)th page to the same location of another free block. (Block ’B’)
* Step3
Then, copy the nth page data of the Block ’A’ in the buffer memory to the nth page of the Block ’B’.
* Step4
Do not erase or program to Block ’A’ by creating an ’invalid block’ table or other appropriate scheme.
Buffer memory of the controller.
1st
Block A
Block B
(n-1)th
nth
(page)
{
1st
(n-1)th
nth
(page)
{
an error occurs.
1
2
FLASH MEMORY
17
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
NAND Flash Technical Notes (Continued)
Within a block, the pages must be programmed consecutively from the LSB (least significant bit) page of the block to MSB (most sig-
nificant bit) pages of the block. Random page address programming is prohibited. In this case, the definition of LSB page is the LSB
among the pages to be programmed. Therefore, LSB doesn’t need to be page 0.
From the LSB page to MSB page
DATA IN: Data (1) Data (64)
(1)
(2)
(3)
(32)
(64)
Data register
Page 0
Page 1
Page 2
Page 31
Page 63
Ex.) Random page program (Prohibition)
DATA IN: Data (1) Data (64)
(2)
(32)
(3)
(1)
(64)
Data register
Page 0
Page 1
Page 2
Page 31
Page 63
Addressing for program operation
:
:
:
:
FLASH MEMORY
18
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
System Interface Using CE don’t-care.
For an easier system interface, CE may be inactive during the data-loading or serial access as shown below. The internal 2,112byte
data registers are utilized as separate buffers for this operation and the system design gets more flexible. In addition, for voice or
audio applications which use slow cycle time on the order of µ-seconds, de-activating CE during the data-loading and serial access
would provide significant savings in power consumption.
Figure 4. Program Operation with CE don’t-care.
CE
WE
tWP
tCH
tCS
Address(5Cycles)80h Data Input
CE
CLE
ALE
WE
Data Input
CE don’t-care
10h
Address(5Cycle)00h
CE
CLE
ALE
WE
Data Output(serial access)
CE don’t-care
R/B tR
RE
tCEA
out
tREA
CE
RE
I/O0~7
Figure 5. Read Operation with CE don’t-care.
30h
I/Ox
I/Ox
FLASH MEMORY
19
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Command Latch Cycle
CE
WE
CLE
ALE
Command
Address Latch Cycle
tCLS
tCS
tCLH
tCH
tWP
tALS tALH
tDS tDH
NOTE
Device I/O DATA ADDRESS
I/Ox Data In/Out Col. Add1 Col. Add2 Row Add1 Row Add2 Row Add3
K9F4G08U0B I/O 0 ~ I/O 7 2,112byte A0~A7 A8~A11 A12~A19 A20~A27 A28~A29
I/Ox
CE
WE
CLE
ALE
Col. Add1
tCS
tWC
tWP
tALS
tDS tDH
tALH tALS
tWH
tWC
tWP
tDS tDH
tALH tALS
tWH
tWC
tWP
tDS tDH
tALH tALS
tWH
tDS tDH
tWP
I/Ox
Col. Add2 Row Add1 Row Add2
tWC
tWH
tALH tALS
tDS tDH
Row Add3
tALH
tCLS
FLASH MEMORY
20
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Input Data Latch Cycle
CE
CLE
WE
DIN 0 DIN 1 DIN final
ALE
tALS
tCLH
tWC
tCH
tDS tDH tDS tDH tDS tDH
tWP
tWH
tWP tWP
I/Ox
* Serial Access Cycle after Read(CLE=L, WE=H, ALE=L)
RE
CE
R/B
Dout Dout Dout
tRC
tREA
tRR
tRHOH
tREA
tREH
tREA tCOH
tRHZ
I/Ox
tCHZ
tRHZ
NOTES : Transition is measured at ±200mV from steady state voltage with load.
This parameter is sampled and not 100% tested.
tRLOH is valid when frequency is higher than 33MHz.
tRHOH starts to be valid when frequency is lower than 33MHz.
FLASH MEMORY
21
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Status Read Cycle
CE
WE
CLE
RE
70h/F1h Status Output
tCLR
tCLH
tWP
tCH
tDS tDH tREA
tIR tRHOH
tCOH
tWHR
tCEA
tCLS
I/Ox
tCHZ
tRHZ
tCS
RE
CE
R/B
I/Ox
tRR
tCEA
tREA
tRP tREH
tRC
tRHZ
tCHZ
Serial Access Cycle after Read(EDO Type, CLE=L, WE=H, ALE=L)
tRHOH
tCOH
tRLOH
Dout Dout
tREA
NOTES : Transition is measured at ±200mV from steady state voltage with load.
This parameter is sampled and not 100% tested.
tRLOH is valid when frequency is higher than 33MHz.
tRHOH starts to be valid when frequency is lower than 33MHz.
FLASH MEMORY
22
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Read Operation(Intercepted by CE)
CE
CLE
R/B
WE
ALE
RE
Busy
00h
Dout N Dout N+1 Dout N+2
Row Address
Column Address
tWB
tAR
tCHZ
tR
tRR
tRC
30h
Read Operation
CE
CLE
R/B
WE
ALE
RE
Busy
00h
Col. Add1 Col. Add2 Row Add1
Dout N Dout N+1
Column Address Row Address
tWB
tAR
tRtRC tRHZ
tRR
Dout M
tWC
Row Add2
30h
tCLR
I/Ox
I/Ox
Col. Add1 Col. Add2 Row Add1 Row Add2
Row Add3
Row Add3
tCOH
FLASH MEMORY
23
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Random Data Output In a Page
CE
CLE
R/B
WE
ALE
RE
Busy
00h Dout N Dout N+1
Row Address
Column Address
tWB
tAR
tR
tRR
t
RC
30h 05h
Column Address
Dout M Dout M+1
I/Ox
Col. Add1 Col. Add2 Row Add1 Row Add2 Col Add1 Col Add2
Row Add3
tCLR
E0h
tWHR
tREA
tRHW
FLASH MEMORY
24
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Page Program Operation
CE
CLE
R/B
WE
ALE
RE
80h 70h I/O
0
Din
N
Din 10h
M
SerialData
Input Command Column Address Row Address 1 up to m Byte
Serial Input
Program
Command
Read Status
Command
I/O
0
=0 Successful Program
I/O
0
=1 Error in Program
tPROG
tWB
tWC tWC tWC
I/Ox Co.l Add1 Col. Add2 Row Add1 Row Add2 Row Add3
NOTES : tADL is the time from the WE rising edge of final address cycle to the WE rising edge of first data cycle.
tADL tWHR
FLASH MEMORY
25
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Page Program Operation with Random Data Input
CE
CLE
R/B
WE
ALE
RE
80h 70h I/O
0
Din
N
Din 10h
M
Serial Data
Input Command Column Address Row Address Serial Input Program
Command
Read Status
Command
tPROG
tWB
tWC tWC
85h
Random Data
Input Command Column Address
tWC
Din
J
Din
K
Serial Input
I/Ox
Col. Add1 Col. Add2 Row Add1 Row Add2 Col. Add1 Col. Add2
Row Add3
NOTES : 1. tADL is the time from the WE rising edge of final address cycle to the WE rising edge of first data cycle.
tADL
tADL
tWHR
FLASH MEMORY
26
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
00h I/O
x
85h
Column Address Row Address
Read Status Command
I/O
0
=0 Successful Program
I/O
0
=1 Error in Program
tPROG
tWB
tWC
Busy
tWB
tR
Busy
10h
Copy-Back Data
Input Command
35h
Column Address Row Address
Data 1 Data N
Col Add1 Col Add2 Row Add1 Row Add2 Col Add1 Col Add2 Row Add1 Row Add2 Row Add3
Row Add3
70h
NOTES :
1. tADL is the time from the WE rising edge of final address cycle to the WE rising edge of first data cycle.
tADL
tWHR
Data 1 Data N
tRC
Copy-Back Program Operation with Random Data Input
CE
CLE
R/B
WE
ALE
RE
I/Ox
FLASH MEMORY
27
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Block Erase Operation
CE
CLE
R/B
WE
ALE
RE
60h
Erase Command
Read Status
Command
I/O
0
=1 Error in Erase
D0h 70h I/O 0
Busy
tWB tBERS
I/O
0
=0 Successful Erase
Row Address
tWC
Auto Block Erase
Setup Command
I/Ox
Row Add1 Row Add2 Row Add3
tWHR
FLASH MEMORY
28
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Two-Plane Page Program Operation
80h
I/O0~7
R/B
11h
Ex.) Two-Plane Page Program
tDBSY
Address & Data Input 81h 10h
Address & Data Input 70h/F1h
tPROG
Col Add1,2 & Row Add 1,2,3
2112 Byte Data
CE
CLE
R/B
WE
ALE
RE
80h Din
NDin 11h
M
Serial Data
Input Command
Column Address
Program
tDBSY
tWB
tWC
Command
(Dummy)
Din
N10h
tPROG
tWB
I/O
Program Confirm
Command
(True)
81h
70h/F1h
Page Row Address
I/Ox
1 up to 2112 Byte Data
Serial Input
Din
M
Read Status Command
t
DBSY :
typ. 500ns
max. 1
µs
Col Add1 Col Add2 Row Add1 Row Add2 Row Add3 Col Add1 Col Add2 Row Add1 Row Add2 Row Add3
Col Add1,2 & Row Add 1,2,3
2112 Byte Data
A0 ~ A11 : Valid
A12 ~ A17 : Fixed ’Low’
A18 : Fixed ’Low’
A19 ~ A29 : Fixed ’Low’
A0 ~ A11 : Valid
A12 ~ A17 : Valid
A18 : Fixed ’High’
A19 ~ A29 : Valid
Note: Any command between 11h and 81h is prohibited except 70h and FFh.
Note
tWHR
FLASH MEMORY
29
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Two-Plane Block Erase Operation
Block Erase Setup Command1 Erase Confirm Command
Read Status Command
60h
Row Add1,2,3
I/O0~7
R/B
60h A9 ~ A25
D0h
tBERS
Ex.) Address Restriction for Two-Plane Block Erase Operation
CE
CLE
R/B
I/OX
WE
ALE
RE
60h Row Add1 D0h 70h/F1h I/O 0
Busy
tWB tBERS
tWC
D0h 70h/F1hAddress Address
Row Add1,2,3
I/O 0 = 0 Successful Erase
I/O 0 = 1 Error in Erase
Row Add2 Row Add3
A12 ~ A17: Fixed ’Low’
A18 : Fixed ’Low’
A19 ~ A29 : Fixed ’Low’
A12 ~ A17 : Fixed ’Low’
A18 : Fixed ’High’
A19 ~ A29 : Valid
60h Row Add1 D0h
Row Add2 Row Add3
Row Address
tWC
Block Erase Setup Command2
Row Address
tWHR
FLASH MEMORY
30
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Read ID Operation
CE
CLE
WE
ALE
RE
90h
Read ID Command Maker Code Device Code
00h ECh
tREA
Address 1cycle
I/Ox
tAR
Device Device Code (2nd Cycle) 3rd Cycle 4th Cycle 5th Cycle
K9F4G08B0B Same as each K9F4G08U0B
K9F4G08U0B DCh 10h 95h 54h
K9K8G08U1B Same as each K9F4G08U0B in it
Device 4th cyc.
Code 3rd cyc. 5th cyc.
FLASH MEMORY
31
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
4th ID Data
Description I/O7 I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 I/O0
Page Size
(w/o redundant area )
1KB
2KB
4KB
8KB
0 0
0 1
1 0
1 1
Block Size
(w/o redundant area )
64KB
128KB
256KB
512KB
0 0
0 1
1 0
1 1
Redundant Area Size
( byte/512byte)
8
16
0
1
Organization x8
x16
0
1
Serial Access Minimum
50ns/30ns
25ns
Reserved
Reserved
0
1
0
1
0
0
1
1
ID Definition Table
90 ID : Access command = 90H
Description
1st Byte
2nd Byte
3rd Byte
4th Byte
5th Byte
Maker Code
Device Code
Internal Chip Number, Cell Type, Number of Simultaneously Programmed Pages, Etc
Page Size, Block Size,Redundant Area Size, Organization, Serial Access Minimum
Plane Number, Plane Size
3rd ID Data
Description I/O7 I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 I/O0
Internal Chip Number
1
2
4
8
0 0
0 1
1 0
1 1
Cell Type
2 Level Cell
4 Level Cell
8 Level Cell
16 Level Cell
0 0
0 1
1 0
1 1
Number of
Simultaneously
Programmed Pages
1
2
4
8
0 0
0 1
1 0
1 1
Interleave Program
Between multiple chips
Not Support
Support
0
1
Cache Program Not Support
Support
0
1
FLASH MEMORY
32
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
5th ID Data
Description I/O7 I/O6 I/O5 I/O4 I/O3 I/O2 I/O1 I/O0
Plane Number
1
2
4
8
0 0
0 1
1 0
1 1
Plane Size
(w/o redundant Area)
64Mb
128Mb
256Mb
512Mb
1Gb
2Gb
4Gb
8Gb
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
Reserved 0 0 0
FLASH MEMORY
33
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Device Operation
PAGE READ
Page read is initiated by writing 00h-30h to the command register along with five address cycles. After initial power up, 00h command
is latched. Therefore only five address cycles and 30h command initiates that operation after initial power up. The 2,112 bytes of data
within the selected page are transferred to the data registers in less than 25µs(tR). The system controller can detect the completion of
this data transfer(tR) by analyzing the output of R/B pin. Once the data in a page is loaded into the data registers, they may be read
out in 25ns cycle time by sequentially pulsing RE. The repetitive high to low transitions of the RE clock make the device output the
data starting from the selected column address up to the last column address.
The device may output random data in a page instead of the consecutive sequential data by writing random data output command.
The column address of next data, which is going to be out, may be changed to the address which follows random data output com-
mand. Random data output can be operated multiple times regardless of how many times it is done in a page.
Figure 6. Read Operation
Address(5Cycle)00h
Col. Add.1,2 & Row Add.1,2,3
Data Output(Serial Access)
Data Field Spare Field
CE
CLE
ALE
R/B
WE
RE
tR
30h
I/Ox
FLASH MEMORY
34
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Figure 7. Random Data Output In a Page
Address
00h Data Output
R/B
RE
tR
30h Address
05h E0h
5Cycles 2Cycles Data Output
Data Field Spare Field Data Field Spare Field
I/Ox
Col. Add.1,2 & Row Add.1,2,3
PAGE PROGRAM
The device is programmed basically on a page basis, but it does allow multiple partial page programming of a word or consecutive
bytes up to 2,112, in a single page program cycle. The number of consecutive partial page programming operation within the same
page without an intervening erase operation must not exceed 4 times for a single page. The addressing should be done in sequential
order in a block. A page program cycle consists of a serial data loading period in which up to 2,112bytes of data may be loaded into
the data register, followed by a non-volatile programming period where the loaded data is programmed into the appropriate cell.
The serial data loading period begins by inputting the Serial Data Input command(80h), followed by the five cycle address inputs and
then serial data loading. The words other than those to be programmed do not need to be loaded. The device supports random data
input in a page. The column address for the next data, which will be entered, may be changed to the address which follows random
data input command(85h). Random data input may be operated multiple times regardless of how many times it is done in a page.
The Page Program confirm command(10h) initiates the programming process. Writing 10h alone without previously entering the
serial data will not initiate the programming process. The internal write state controller automatically executes the algorithms and tim-
ings necessary for program and verify, thereby freeing the system controller for other tasks. Once the program process starts, the
Read Status Register command may be entered to read the status register. The system controller can detect the completion of a pro-
gram cycle by monitoring the R/B output, or the Status bit(I/O 6) of the Status Register. Only the Read Status command and Reset
command are valid while programming is in progress. When the Page Program is complete, the Write Status Bit(I/O 0) may be
checked(Figure 8). The internal write verify detects only errors for "1"s that are not successfully programmed to "0"s. The command
register remains in Read Status command mode until another valid command is written to the command register.
Figure 8. Program & Read Status Operation
80h
R/B
Address & Data Input I/O0 Pass
Data
10h 70h
Fail
tPROG
I/Ox
Col. Add.1,2 & Row Add.1,2,3
"0"
"1"
Col. Add.1,2
FLASH MEMORY
35
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Figure 9. Random Data Input In a Page
80h
R/B
Address & Data Input I/O0 Pass
10h 70h
Fail
tPROG
85h Address & Data Input
I/Ox
Col. Add.1,2 & Row Add1,2,3 Col. Add.1,2
Data Data
COPY-BACK PROGRAM
Copy-Back program with Read for Copy-Back is configured to quickly and efficiently rewrite data stored in one page without data re-
loading when the bit error is not in data stored. Since the time-consuming re-loading cycles are removed, the system performance is
improved. The benefit is especially obvious when a portion of a block is updated and the rest of the block also needs to be copied to
the newly assigned free block. Copy-Back operation is a sequential execution of Read for Copy-Back and of copy-back program with
the destination page address. A read operation with "35h" command and the address of the source page moves the whole 2,112-byte
data into the internal data buffer. A bit error is checked by sequential reading the data output. In the case where there is no bit error,
the data do not need to be reloaded. Therefore Copy-Back program operation is initiated by issuing Page-Copy Data-Input command
(85h) with destination page address. Actual programming operation begins after Program Confirm command (10h) is issued. Once
the program process starts, the Read Status Register command (70h) may be entered to read the status register. The system control-
ler can detect the completion of a program cycle by monitoring the R/B output, or the Status bit(I/O 6) of the Status Register. When
the Copy-Back Program is complete, the Write Status Bit(I/O 0) may be checked(Figure 10 & Figure 11). The command register
remains in Read Status command mode until another valid command is written to the command register.
During copy-back program, data modification is possible using random data input command (85h) as shown in Figure11.
Figure 10. Page Copy-Back Program Operation
Figure 11. Page Copy-Back Program Operation with Random Data Input
Note: 1. Copy-Back Program operation is allowed only within the same memory plane.
"0"
"1"
"0"
"1"
00h
R/B
Add.(5Cycles) I/O0 Pass
Fail
tPROG
tR
Source Address
Destination Address
I/Ox
Col. Add.1,2 & Row Add.1,2,3
Col. Add.1,2 & Row Add.1,2,3
35h Data Output 85h Add.(5Cycles) 10h 70h
R/B
Source Address
Destination Address
There is no limitation for the number of repetition.
I/Ox
Col. Add.1,2 & Row Add.1,2,3 Col. Add.1,2 & Row Add.1,2,3 Col. Add.1,2
00h Add.(5Cycles) 35h
tR
Data Output
85h
Add.(5Cycles) Data
85h Add.(2Cycles) Data
10h
tPROG
70h
FLASH MEMORY
36
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Figure 12. Block Erase Operation
BLOCK ERASE
The Erase operation is done on a block basis. Block address loading is accomplished in three cycles initiated by an Erase Setup
command(60h). Only address A18 to A29 is valid while A12 to A17 is ignored. The Erase Confirm command(D0h) following the block
address loading initiates the internal erasing process. This two-step sequence of setup followed by execution command ensures that
memory contents are not accidentally erased due to external noise conditions.
At the rising edge of WE after the erase confirm command input, the internal write controller handles erase and erase-verify. When
the erase operation is completed, the Write Status Bit(I/O 0) may be checked. Figure 12 details the sequence.
60h
Row Add 1,2,3
R/B
Address Input(3Cycle) I/O0 Pass
D0h 70h
Fail
tBERS
I/Ox
"0"
"1"
TWO-PLANE PAGE PROGRAM
Two-Plane Page Program is an extension of Page Program, for a single plane with 2112 byte page registers. Since the device is
equipped with two memory planes, activating the two sets of 2112 byte page registers enables a simultaneous programming of two
pages.
After writing the first set of data up to 2112 byte into the selected page register, Dummy Page Program command (11h) instead of
actual Page Program command (10h) is inputted to finish data-loading of the first plane. Since no programming process is involved,
R/B remains in Busy state for a short period of time(tDBSY). Read Status command (70h/F1h) may be issued to find out when the
device returns to Ready state by polling the Ready/Busy status bit(I/O 6). Then the next set of data for the other plane is inputted
after the 81h command and address sequences. After inputting data for the last plane, actual True Page Program(10h) instead of
dummy Page Program command (11h) must be followed to start the programming process. The operation of R/B and Read Status is
the same as that of Page Program. Althougth two planes are programmed simultaneously, pass/fail is not available for each page
when the program operation completes. Status bit of I/O 0 is set to "1" when any of the pages fails.
Restriction in addressing with Two-Plane Page Program is shown is Figure13.
FLASH MEMORY
37
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Figure 13. Two-Plane Page Program
80h 11h
Data
Input
Plane 0
(2048 Block)
Block 0
Block 2
Block 4094
Block 4092
80h
I/O0 ~ 7
R/B
Address & Data Input 11h 81h 10h
tDBSY tPROG
70h/F1h
Address & Data Input
NOTE :1. It is noticeable that same row address except for A18 is applied to the two blocks
81h 10h
Plane 1
(2048 Block)
Block 1
Block 3
Block 4095
Block 4093
Figure 14. Two-Plane Block Erase Operation
60h
I/OX
R/B
60h D0h I/O0 Pass
Fail
tBERS
Address (3 Cycle) Address (3 Cycle) 70h/F1h "0"
"1"
A12 ~ A17 : Fixed ’Low’
A18 :Fixed ’Low’
A19 ~ A29 : Fixed ’Low’
A12 ~ A17 : Fixed ’Low’
A18 : Fixed ’High’
A19 ~ A29 : valid
TWO-PLANE BLOCK ERASE
Basic concept of Two-Plane Block Erase operation is identical to that of Two-Plane Page Program. Up to two blocks, one from each
plane can be simultaneously erased. Standard Block Erase command sequences (Block Erase Setup command(60h) followed by
three address cycles) may be repeated up to twice for erasing up to two blocks. Only one block should be selected from each plane.
The Erase Confirm command(D0h) initiates the actual erasing process. The completion is detected by monitoring R/B pin or Ready/
Busy status bit (I/O 6).
A0 ~ A11 : Valid
A12 ~ A17 : Fixed ’Low’
A18 : Fixed ’Low’
A19 ~ A29 : Fixed ’Low’
A0 ~ A11 : Valid
A12 ~ A17 : Valid
A18 : Fixed ’High’
A19 ~ A29 : Valid
2. Any command between 11h and 81h is prohibited except 70h/F1h and FFh.
Note*2
FLASH MEMORY
38
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Figure 15. Two-Plane Copy-Back Program Operation
00h
R/B
Add.(5Cycles)
tR
Source Address On Plane0
35h
I/Ox
Col. Add.1,2 & Row Add.1,2,3
TWO-PLANE COPY-BACK PROGRAM
Two-Plane Copy-Back Program is an extension of Copy-Back Program, for a single plane with 2112 byte page registers. Since the
device is equipped with two memory planes, activating the two sets of 2112 byte page registers enables a simultaneous program-
ming of two pages.
1
R/B
85h 70h/F1h
tPROG
Add.(5Cycles)
Destination Address
10h
I/Ox
Col. Add.1,2 & Row Add.1,2,3
81h Add.(5Cycles)
Destination Address
Col. Add.1,2 & Row Add.1,2,3
11h
tDBSY
A0 ~ A11 : Fixed ’Low’
A12 ~ A17 : Valid
A18 : Fixed ’High’
A19 ~ A29 : Valid
1
Note2
A0 ~ A11 : Fixed ’Low’
A12 ~ A17 : Fixed ’Low’
A18 : Fixed ’Low’
A19 ~ A29 : Fixed ’Low’
Data Field Spare Field Data Field Spare Field
(1) (2)(3) (3)
Plane0 Plane1
Source page
Target page
Source page
Target page (1) : Read for Copy Back On Plane0
(2) : Read for Copy Back On Plane1
(3) : Two-Plane Copy-Back Program
Note: 1. Copy-Back Program operation is allowed only within the same memory plane.
2. Any command between 11h and 81h is prohibited except 70h/F1h and FFh.
00h Add.(5Cycles)
Source Address On Plane1
35h
Col. Add.1,2 & Row Add.1,2,3
tR
Data OutputData Output
FLASH MEMORY
39
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Figure 16. Two-Plane Copy-Back Program Operation with Random Data Input
R/B
85h 11h
tDBSY
Add.(5Cycles) Data 85h Data
I/Ox
Col. Add.1,2 & Row Add.1,2,3 Col. Add.1,2
Add.(2Cycles)
00h
R/B
Add.(5Cycles)
tR
Source Address On Plane0
35h
I/Ox
Col. Add.1,2 & Row Add.1,2,3
1
R/B
81h 10h
tPROG
Add.(5Cycles) Data 85h Data
I/Ox
Col. Add.1,2 & Row Add.1,2,3 Col. Add.1,2
Add.(2Cycles)
12
2
Destination Address
A0 ~ A11 : Valid
A12 ~ A17 : Fixed ’Low’
A18 : Fixed ’Low’
A19 ~ A29 : Fixed ’Low’
Destination Address
A0 ~ A11 : Valid
A12 ~ A17 : Valid
A18 : Fixed ’High’
A19 ~ A29 : Valid
Note: 1. Copy-Back Program operation is allowed only within the same memory plane.
2. Any command between 11h and 81h is prohibited except 70h/F1h and FFh.
Note2
00h Add.(5Cycles)
Source Address On Plane1
35h
Col. Add.1,2 & Row Add.1,2,3
tR
Data OutputData Output
FLASH MEMORY
40
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
READ STATUS
The device contains a Status Register which may be read to find out whether program or erase operation is completed, and whether
the program or erase operation is completed successfully. After writing 70h/F1h command to the command register, a read cycle out-
puts the content of the Status Register to the I/O pins on the falling edge of CE or RE, whichever occurs last. This two line control
allows the system to poll the progress of each device in multiple memory connections even when R/B pins are common-wired. RE or
CE does not need to be toggled for updated status. Refer to Table 3 for specific Status Register definitions and Table 4 for specific
F1h Status Register definitions. The command register remains in Status Read mode until further commands are issued to it. There-
fore, if the status register is read during a random read cycle, the read command(00h) should be given before starting read cycles.
Table 3. Status Register Definition for 70h Command
NOTE : 1. I/Os defined ’Not use’ are recommended to be masked out when Read Status is being executed.
I/O Page Program Block Erase Read Definition
I/O 0 Pass/Fail Pass/Fail Not use Pass : "0" Fail : "1"
I/O 1 Not use Not use Not use Don’t -cared
I/O 2 Not use Not use Not use Don’t -cared
I/O 3 Not Use Not Use Not Use Don’t -cared
I/O 4 Not Use Not Use Not Use Don’t -cared
I/O 5 Not Use Not Use Not Use Don’t -cared
I/O 6 Ready/Busy Ready/Busy Ready/Busy Busy : "0" Ready : "1"
I/O 7 Write Protect Write Protect Write Protect Protected : "0" Not Protected : "1"
Table 4. F1h Read Status Register Definition
NOTE : 1. I/Os defined ’Not use’ are recommended to be masked out when Read Status is being executed.
I/O No. Page Program Block Erase Read Definition
I/O 0 Chip Pass/Fail Chip Pass/Fail Not use Pass : "0" Fail : "1"
I/O 1 Plane0 Pass/Fail Plane0 Pass/Fail Not use Pass : "0" Fail : "1"
I/O 2 Plane1 Pass/Fail Plane1 Pass/Fail Not use Pass : "0" Fail : "1"
I/O 3 Not Use Not Use Not Use Don’t -cared
I/O 4 Not Use Not Use Not Use Don’t -cared
I/O 5 Not Use Not Use Not Use Don’t -cared
I/O 6 Ready/Busy Ready/Busy Ready/Busy Busy : "0" Ready : "1"
I/O 7 Write Protect Write Protect Write Protect Protected : "0" Not Protected : "1"
FLASH MEMORY
41
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
Figure 17. Read ID Operation
CE
CLE
I/OX
ALE
RE
WE
90h 00h
Address. 1cycle Maker code Device code
tCEA
tAR
tREA
READ ID
The device contains a product identification mode, initiated by writing 90h to the command register, followed by an address input of
00h. Five read cycles sequentially output the manufacturer code(ECh), and the device code and 3rd, 4th, 5th cycle ID respectively.
The command register remains in Read ID mode until further commands are issued to it. Figure 17 shows the operation sequence.
Figure 18. RESET Operation
RESET
The device offers a reset feature, executed by writing FFh to the command register. When the device is in Busy state during random
read, program or erase mode, the reset operation will abort these operations. The contents of memory cells being altered are no
longer valid, as the data will be partially programmed or erased. The command register is cleared to wait for the next command, and
the Status Register is cleared to value C0h when WP is high. If the device is already in reset state a new reset command will be
accepted by the command register. The R/B pin changes to low for tRST after the Reset command is written. Refer to Figure 18
below.
FFh
I/OX
R/B tRST
tWHR
tCLR
Device Device Code (2nd Cycle) 3rd Cycle 4th Cycle 5th Cycle
K9F4G08B0B Same as each K9F4G08U0B
K9F4G08U0B DCh 10h 95h 54h
K9K8G08U1B Same as each K9F4G08U0B in it
Device 4th Cyc.
Code
ECh 3rd Cyc. 5th Cyc.
Table 5. Device Status
After Power-up After Reset
Operation mode 00h Command is latched Waiting for next command
FLASH MEMORY
42
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
READY/BUSY
The device has a R/B output that provides a hardware method of indicating the completion of a page program, erase and random
read completion. The R/B pin is normally high but transitions to low after program or erase command is written to the command regis-
ter or random read is started after address loading. It returns to high when the internal controller has finished the operation. The pin is
an open-drain driver thereby allowing two or more R/B outputs to be Or-tied. Because pull-up resistor value is related to tr(R/B) and
current drain during busy(ibusy) , an appropriate value can be obtained with the following reference chart(Fig.19). Its value can be
determined by the following guidance.
VCC
R/B
open drain output
Device
GND
Rp
tr,tf [s]
Ibusy [A]
Figure 19. Rp vs tr ,tf & Rp vs ibusy
ibusy
Busy
Ready Vcc
VOH
tf tr
VOL
where IL is the sum of the input currents of all devices tied to the R/B pin.
Rp value guidance
Rp(max) is determined by maximum permissible limit of tr
Rp(min, 3.3V part) = VCC(Max.) - VOL(Max.)
IOL + ΣIL
=
3.2V
8mA + ΣIL
3.3V device - VOL : 0.4V, VOH : 2.4V
CL
Rp(ohm)
Ibusy
tr
@ Vcc = 3.3V, Ta = 25
°
C , C
L
= 50pF
1K 2K 3K 4K
100n
200n 2m
1m
50
tf
100
150
200
3.6 3.6 3.6 3.6
2.4
1.2
0.8
0.6
tr,tf [s]
Ibusy [A]
Rp(min, 2.7V part) = VCC(Max.) - VOL(Max.)
IOL + ΣIL
=
2.5V
3mA + ΣIL
Rp(ohm)
Ibusy
tr
@ Vcc = 2.7V, Ta = 25
°
C , C
L
= 30pF
1K 2K 3K 4K
100n
200n 2m
1m
30
tf
60
90
120
2.3 2.3 2.3 2.3
2.3
1.1
0.75 0.55
FLASH MEMORY
43
K9F4G08U0B
K9K8G08U1B K9F4G08B0B
Advance
Samsung Confidential
DATA PROTECTION & POWER UP SEQUENCE
The device is designed to offer protection from any involuntary program/erase during power-transitions. An internal voltage detector
disables all functions whenever Vcc is below about 1.8V(2.7V device), 2V(3.3V device). WP pin provides hardware protection and is
recommended to be kept at VIL during power-up and power-down. A recovery time of minimum 100µs is required before internal cir-
cuit gets ready for any command sequences as shown in Figure 20. The two step command sequence for program/erase provides
additional software protection.
Figure 20. AC Waveforms for Power Transition
VCC
WP
High
WE
Ready/Busy
5 ms max Operation
Note :During the initialization, the device consumes a maximum current of 30mA (ICC1)
100µs
~ 2.3V ~ 2.3V
Invalid Don’t care
Don’t care