Customer: ALPS EUROPE DISTRIBUTION No. KX-2010-0165 Date: Aug. 11, 2010 Attention: Your ref. No.: Your Part No.: RK09K1130C79 SPECIFICATIONS ALPS' ; MODEL: RKO9K1130C79 (10k B ) Spec. No.: Sample No.. GO660778M RECEIPT STATUS RECEIVED By Date Signature Name Title Lu.Lin YM ALPS. * ALPS ELECTRIC CO., LTD. APP'D AS. Sate ENG. DEPT. Sales Head Office 1-7, Yukigaya-otsuka-machi, Ota-ku, Tokyo, 145-8501 Japan + Phone,+81(3)3726-1211 B6523 Q1003#03A (EA) ~No. KX-2010-0165 SPECIFICATIONS 1. THIS SPECIFICATIONS APPLY TO RKO9K1130C79 POTENTIOMETER. 2. CONTENTS OF THIS SPECIFICATIONS. G0660778M K091C024G 3. MARKING * MARKING ON ALL UNITS DATE CODE, RESIST. VALUE, TAPER * NOTES This unit uses polycarbonate. To be careful for using this unit in such violent gas atmospheric condition as ammonia, amine, alkaline aqueous solution, aromatic hydrocarbon, keton, ester, alkyl hydrocarbon, etc. = CAUTION There is a possibility that might be affected by contact resistance of resistive element and wiper in case of low impedance of output side in voltage regulation circuit. For this reason, we require that you adjust to impedance of output side more than 100 times of total resistance. 1.For the export of products which are controlled items subject to foreign and domestic export laws and regulations, you must obtain approval and/or follow the formalities of such laws and regulations. 2,Products must not be used for military and/or antisocial purposes such as terrorism, and shall not be supplied to any party intending to use the products for such purposes. 3.Unless provided otherwise, the products have been designed and manufactured for application to equipment and devices which are sold to end-users in the market, such as AV (audio visual) equipment, home electric equipment, office and commercial electronic equipment, information and communication equipment or amusement equipment. The products are not intended for use in, and must not be used for, any application of nuclear equipment, driving control equipment for aerospace or any other unauthorized use. With the exception of the above mentioned banned applications, for applications involving high levels of safety and liability such as medical equipment, burglar alarm equipment, disaster prevention equipment and undersea equipment, please contact an Alps sales representative and/or evaluate the total system on the applicability. Also, implement a fail-safe design, protection circuit, redundant circuit, malfunction protection and/or fire protection into the complete system for safety and reliability of the total system. 4.Before using products which were not specifically designed for use in automotive applications, please contact an Alps sales representative. 5.The products shall be stored in the original packaging and kept at room temperature and humidity, out of direct sunlight, and away from any and all corrosive gas. The products shall be completely used as soon as possible, but no later than 6 months from the date of delivery. Once product packaging is opened, the complete quantity of such products shall be promptly used.SPECIFICATIONS ELECTRICAL 1. Total resistance : 10k o 420% 2. Rated power : 0.05 W 3. Rated voltage : The rated voltage shail be the voltage of D.C. or A.C. (commercial frequency .effective value ) corresponding to the rated power (dissipation). and be obtained from the following formula. when the obtained rated voltage exceeds the maximum working voltage given In the following, however. the maximum working voltage of the following shall be the rated voltage. E = /P-R (Vv) where E : Rated voltage (V) P : Rated power(dissipation) (Ww) R : Nominal total resistance (a) Maximum working voltage : 50 V A.C. . 20 V D.C. 4.Residual resistance between terminals between term.1&2, term.2&3 : 3000 max. 5. Sliding noise : Less than 100 mV measured by method of JIS C 6443. 6. Insulation resistance : Greater than 100 Mo measured by D.C. 250V. 7. withstand voltage: More than 1 minute with an application of A.C. 250 V. 8. Taper : B MECHANICAL e 1. Overall rotational angle : 280 5 2. Operation torque > 1-mN-m (Rotational speed 60 /sec. ) 3. Shaft end stop strength : No damage with an application of 0. 3N-m. 4. Starting toruque > 1OMN-m MAX. 5. Resistance to soidering heat : After soldering (Less than 350C and qutcker than 3 seconds) there shall be no evidence of poor contact between resistance element and terminals. or any physical damages as a result of the test. 6.Play of shaft : The resistor shall be mounted by soldering the mounting legs on the panel. Then a side thrust of 25mN-m at the end of the shaft shall be applied, then the total ptay of the shaft shall not exceed 0.5x L / 20 mm D-DD. (L:Shaft length) 7. Inclination of shaft : The eccentricity of the root of shaft shail not exceed 0. 35mm against the center of the mounting position. 8. Eccentricity of shaft : The inclination of shaft shall be within 0. 35mm to the center of shaft which Is parallel to the mounting surface. 9. Robustness of shaft against end thrust : The shaft shall withstand against end thrust of SON for 3 seconds. 10. Robustness of shaft against side thrust : The shaft shall withstand against side thrust of 40N for 3 seconds on the end of the shaft at right angles to the axis of the shaft after mounting the resistor by soldering. ENDURANCE 14,.Rotational life : .000 cycles min. NOTE 1. The items except above mentioned, items shall meet or exceed JIS Cc 6443. 2. Operating temperature :-10 C~t+70 C, 3.Storage temperature :-30 C~+70 C. ALPS ELECTRIC CO., LTD. APPD. CHKO. 0560. TITLE 560. 13. 96 | Sep. 13. 96 | Sep, 13. 96 DOCUMENT NO. Syme | DATE |[APPD |CHKO |oS@D 5, Aizawa m, Satoh |b Sa/toh | GQ gG60778M | | | | I | | KXGe ALPS ELECTRIC CO.,LTD 1-7 YUKIGAYA OTSUKA-CHO OTA-KU TOKYO JAPAN (%) 100 a L 90 7 80 : ZL Y : / 60 X100% ?> N 50/7 INPUT VOLTAGE 40 7 30 LL : 20 10 a VY 0 28 56 84 112 140 168 196 224 252 280 TERM. 1 .W. ROTATION ANGLE > TERM. 3 FULL C.C.W. POSITION 1-2 OUTPUT VOLTAGE 1-3 TERM. TERM AT 140 C.W. SHAFT ROTATION FROM FULL C.C.W. POSITION VOLTAGE PERCENT SHALL FALL WITHIN THE LIMITS OF 40*%60 PERCENT. APPD. CHKD. ps@o. NAME dul. 13.93) val. 13.93| Jul. 19 993| RESISTANCE TAPER (B ) DOCUMENT NO. sya | bATE Tappo |cnko losep | 4. Magam/| x. Sasaki. Suzuti G0660778M || | | | | | kxog Format by 5. Satal2520.5 (6.8) 2240.15 4. 5-05.08 $640.1 | p Ul j k 1 is \ a. axes" cua 42 0. 8X45 CHAM 3.220. 4|| 123 T . 0 Y 3.840. 3 BH 77ybh BOG -0.08 MOUNTING SURFACE 96.2 osWI THIN = GE OF THE FRAME . ! eee THIS LENGTH. Isl S Weer 7-HRezt. o| | 2 SHAFT SHOWN IN s| Tho - CENTER POSITION. ms . oo sy 10.6 Se 1. 9's? . at si __ xX xX oe aze CIRCUIT ~ Y 3 2 2. QERBEFALBL A EKESET. SHAFT SHOWN IN Rs l Me REA Tee RAMS RRE) FULL C.C.W. POSITION. t MOUNTING HOLE DETAIL (TOLERANCESO. 1) VIWED FROM MOUNTING SIDE Oa8E:1.8 9 NET WEIGHT HESERRONRSE TOLERANCES SNLESS OTHERWISE SPEC L==10 +0. 3 140 <L<100/0. 5 100 <=t |40. 8 fi 8 +5 AMGULAR OUMENSION SHAFT COLOR >: BLACK(B) PART NO. NANE MATERIAL NAME / CODE FINISH ALPS ELECTRIC Co., LTD. DSGD. 1-a818 SCALE NO. Y.Salitoh 96-09-13/2 :1 GO0660778M CHKO. TITLE Y. gaton s6-o9-13/@Stlow 1 MRBSEAVR APPD. UNIT DOCUMENT NO. Fi8 SYMB | OATE appolcHkolosaon}S. Alzawa 96-09-13} MM |KO9O1COZ4GCLASS No. TITLE <UNR ATO CESS A> Caution for soldering BOKIEP. W. BOLERELAAD ET ORSK SRT CL, Please avoid soldering on upper surface of P.W.B.as shown ohe et Solder Terminal bhe Solder P.W.B. BREBACHSSREUR LER L CRASS, Solder all metal inserted fixing including terminals & metal lugs into a substrate. ALPS ELECTRIC CO., LTD. APPD. CHKD. DSGD. TITLE DSG1 OSGi OSGi Y VOSHIOKA | Y. SATO |Y.OVA DOCUMENT NO. syYMB DATE TAPPD lcnkn losap | 1296/01/11] 1996/01/11] 1996/01/11 GO6B660778M (1/71)