ATC Analog Technology, AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Features General Description 1.4V maximum dropout at full load current * Fast transient response * Output current limiting * Built-in thermal shutdown * Packages: SOT223, TO252, TO220, SOT89 * Good noise rejection * 3-Terminal Adjustable or Fixed 1.5V, 1.8V,2.5V, 3.3V, 5.0V AP1117 is a low dropout positive adjustable or fixed-mode regulator with minimum of 1A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. AP1117 is also well suited for other applications such as VGA cards. AP1117 is guaranteed to have <1.3V dropout at full load current making it ideal to provide well regulated outputs of 1.25 to 5.0 with 6.3 to 12V input supply. * Applications * * PC peripheral Communication Ordering Information AP 1117 X XX X Package Low Dropout Regulator Vout E : SOT223-3L D : TO252-3L T : TO220-3L Y : SOT89-3L Packing Blank : ADJ Blank : Tube 15 : 1.5V A : Taping 18 : 1.8V 25 : 2.5V 33 : 3.3V 50 : 5.0V Typical Circuit 5V 5V C1 100uF C1 100uF Vin Vin Vout GND Vo Vout 3.3V/1A C2 100uF Adj Tab is Vout R1 121 R2 121 2.5V/1A C2 100uF Tab is Vout ( 5V/2.5V ADJ output ) ( 5V/3.3V fixed output ) Note: Vo = VREF (1+ R2 ) R1 This datasheet contains new product information. Analog Technology reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of this product. No rights under any patent accompany the sale of the product. Rev. A4. Apr. 18, 2003 1/7 ATC AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Connection Diagram 3 PIN SOT223 3 PIN TO252 ( Top View ) ( Top View ) 3 Vin 2 Vout Vin 3 Vout 2 1 Adj (GND) 1 Tab is Vout Adj (GND) Tab is Vout 3 PIN SOT89 3 PIN TO220 Vin 3 Vin 2 Vout 2 Vout 1 Adj (GND) 1 Adj (GND) 3 Tab is Vout Tab is Vout Block Diagram 3 2 Vout + + - 1.25V CURRENT LIMIT + Thermal Shutdown + 1 - Vin GND (FIXED) 1 Rev. A4 2/8 Adj APR. 18, 2003 ATC AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Pin Descriptions NAME I/O PIN # FUNCTION Adj (GND) I 1 A resistor divider from this pin to the Vout pin and ground sets the output voltage. (Ground only for Fixed-Mode) Vout O 2 The output of the regulator. A minimum of 10uF capacitor must be connected from this pin to ground to insure stability. 3 The input pin of regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.3V higher than Vout in order for the device to regulate properly. Vin I Absolute Maximum Ratings DC Supply Voltage (Vin) ........................................................ -0.3 to 12 V Power Dissipation ......................................................... Internally Limited Storage Temperature .......................................................... -65 to +150 oC Operating Junction Temperature Range ........................................... 0 to +150 oC Rev. A4 3/8 APR. 18, 2003 ATC AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Electrical Characteristics (Under Operating Conditions) PARAMETER Reference Voltage CONDITIONS AP1117-ADJ AP1117-1.5 AP1117-1.8 Output Voltage AP1117-2.5 AP1117-3.3 AP1117-5.0 Line Regulation AP1117-XXX AP1117-ADJ AP1117-1.5 AP1117-1.8 Load Regulation AP1117-2.5 AP1117-3.3 AP1117-5.0 Dropout Voltage (VIN-VOUT) o TJ=25 C,(VIN-OUT)=1.5V IO=10mA o IOUT = 10mA, TJ = 25 C, 3VVIN12V o IOUT = 10mA, TJ = 25 C, 3.3VVIN12V o IOUT = 10mA, TJ = 25 C, 4VVIN12V o IOUT = 10mA, TJ = 25 C, 4.8VVIN12V o IOUT = 10mA, TJ = 25 C, 6.5VVIN12V IO=10mA,VOUT+1.5V<VIN<12V, TJ=25oC VIN=3.3V,Vadj=0,0mA<Io<1A, TJ=25oC (Note 1,2) VIN=3V, 0mA<Io<1A, TJ=25oC (Note 1,2) VIN=3.3V, 0mA<Io<1A, TJ=25oC (Note 1,2) VIN=4V, 0mA<Io<1A, TJ=25oC (Note 1,2) VIN = 5V, 0IOUT1A, o TJ=25 C (Note 1,2) VIN = 8V, 0IOUT1A, o TJ=25 C (Note 1,2) AP1117-ADJ/1.5/1.8 2.5/3.3/5.0 AP1117-ADJ/1.5/1.8 2.5/3.3/5.0 (VIN-VOUT) = 5V Minimum Load Current AP1117-XXX 0oCTj125oC Thermal Regulation TA=25, 30ms pulse Ripple Rejection Temperature Stability Current Limit MIN TYP MAX UNIT 1.225 1.250 1.275 V 1.470 1.500 1.530 V 1.764 1.800 1.836 V 2.450 2.500 2.550 V 3.235 3.300 3.365 V 4.900 5.000 5.100 V 0.2 % 1 % 12 15 mV 15 18 mV 20 25 mV 26 33 mV 40 50 mV 1.3 1.4 V IOUT = 1A ,VOUT=0.1%VOUT 1. 1 A 5 10 mA 0.008 0.04 %/W F=120Hz,COUT=25uF Tantalum, IOUT=1A AP1117-XXX VIN=VOUT+3V 60 70 dB IO=10mA 0.5 JA Thermal Resistance SOT89 SOT-223 Junction-to-Ambient(No TO-252 heat sink ;No air flow) TO-220 SOT89 : Control Circuitry/Power Transistor JC Thermal Resistance SOT-223 : Control Circuitry/Power Transistor TO-252 : Control Circuitry/Power Transistor Junction-to-Case TO-220 : Control Circuitry/Power Transistor % 300 117 92 85 100 15 10 0.65/2.7 O C/W O C/W Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18" from the package. Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note3: Quiescent current is defined as the minimum output current required to maintain regulation. At 12V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. Rev. A4 4/8 APR. 18, 2003 ATC AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Typical Performance Characteristics 0.20 2. 0 Output Voltage Deviation (%) 1. 8 1. 6 Dropout Voltage (V) 1. 4 1. 2 0 I load=800mA -0.20 Tj = 25 oC 1. 0 -0.40 0. 8 Tj = 125 oC 0. 6 -0.80 0. 4 0. 2 0 0 200 400 Output Current (mA) 600 -1 800 -25 Dropout Voltage vs Output Current 0 25 50 Temperature (oC) 75 100 125 Load Regulation vs Temperature 2 1 0.8 1 Output Voltage Deviation (%) Output Voltage Change (%) 1.5 0. 5 0 -0.5 -1 -1.5 -2 -50 -25 0 25 50 Temperature (oC) 75 100 125 150 0.6 0.4 0.2 0 2 4 7.5 Cin=1uF Cout=10uF Tantalum 6.5 5.5 40 20 0 -20 -40 0 20 40 60 80 100 120 140 160 180 200 TIME (us) Line Transient Response 8 10 12 Line Regulation Load Current (A) Output Voltage Deviation (mV) Output Voltage Deviation (mV) Input Voltage (V) Percent Change in Output Voltage vs Temperature 6 Input Voltage (V) 30 C in = 1uF C out = 10 uF Tantalum Preload = 100mA 20 10 0 -10 -20 2 1 0 -1 0 10 20 30 40 50 TIME (us) 60 70 80 90 100 Load Transient Response Rev. A4 5/8 APR. 18, 2003 ATC AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Marking Information (1) SOT223-3L (2) TO252-3L (Top view) (Top view) Logo ATCXXX Output Type: 1117: Adjustable 17-15: 1.5V 17-18: 1.8V 17-25: 2.5V 17-33: 3.3V 17-50: 5.0V ID Code Month: A~L = 01~12 1117 Year: "1" = 2001 "2" = 2002 ~ Output Type: 1117 : ADJ 17-15: 1.5V 17-18: 1.8V 17-25: 2.5V 17-33: 3.3V 17-50: 5.0V ATC 1 7- 33 XXXX X Logo ID Code Xth Week: 01~52 Year: "01" = 2001 "02" = 2002 ~ (3) TO220-3L (4) SOT89-3L ( Top view ) ATC 1117-33 XX XX X XX XX Output Type: 1117: ADJ 1117-15: 1.5V 1117-18: 1.8V 1117-25: 2.5V 1117-33: 3.3V 1117-50: 5.0V Date Code Month: A~L Year: 0~9 Logo ID code Xth week: 01~52 Year: "01" = 2001 "02" = 2002 1 2 Identification Code ( See the table ) 3 ~ Identification code Output version DA AP1117-ADJ DB AP1117-1.5V DC AP1117-1.8V DD AP1117-2.5V DE AP1117-3.3V DF AP1117-5.0V Rev. A4 6/8 APR. 18, 2003 ATC AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator Package Dimension (1) SOT223-3L D B1 A SEATING PLANE c H E K e1 e L SYMBOL S A A1 B B1 c D E A1 B Notes: 1. JEDEC Outline: TO-261AA H L K DIMENSIONS IN INCH MIN NOM MAX 0.059 0.065 0.071 0.0008 0.002 0.003 0.024 0.028 0.031 0.114 -- 0.124(REF) 0.011 0.012 0.013 0.248 0.256 0.264 0.13 0.138 0.146 e 0.09 BSC e1 0.181 BSC 0.264 0.276 0.287 0.036 0.039 0.043 0.059 0.069 0.079 o 10 0 5 o -- -- 13 (2) TO252-3L Variations ( Dimensions show in inch) A L2 SYMBOLS D SEATING PLANE C1 H E b2 L1 SEE NOTE2 b e e1 A1 C Notes: 1. JEDEC Outline: TO-252 AB 2. Mils suggested for positive contact at mounting. A A1 b b2 C C1 D E e e1 H L L1 L2 DIMENSIONS IN INCH MIN MAX 0.086 0.094 0.040 0.050 0.024 TYP. 0.205 0.215 0.018 0.023 0.018 0.023 0.210 0.220 0.250 0.265 0.090 BSC. 0.180 BSC. 0.370 0.410 0.020 -- 0.025 0.040 0.06 0.08 Rev. A4 7/8 APR. 18, 2003 ATC AP1117 1A Low Dropout Positive Adjustable or Fixed-Mode Regulator (3) TO220-3L E A P F DIMENSIONS IN INCH MIN MAX 0.14 0.19 0.045 0.07 0.02 0.045 0.012 0.045 0.56 0.65 0.38 0.42 0.09 0.11 0.19 0.21 0.02 0.055 0.23 0.27 0.08 0.115 0.5 0.58 0.139 0.161 0.1 0.135 A b1 b C D E e e1 F H1 J1 L oP Q L1 D SEATING PLANE Q SYMBOLS L b1 C b J1 e e1 (4) SOT89 D1 HE E SYMBOLS 50(2x) L e1 80(2x) c e A D b b1 b DIMENSIONS IN MILLIMETER DIMENSIONS IN INCHES MIN NOM MAX MIN NOM A 1.40 1.50 1.60 0.055 0.059 0.063 B 0.36 0.42 0.48 0.014 0.016 0.018 b1 0.41 0.47 0.53 0.016 0.043 0.051 C 0.38 0.40 0.43 0.014 0.015 0.017 D 4.40 4.50 4.60 0.173 0.177 0.181 D1 1.40 1.60 1.75 0.055 0.062 0.069 E 2.90 3.00 3.10 0.114 0.118 0.122 e1 1.45 1.50 1.55 0.057 0.059 0.061 E 2.40 2.50 2.60 0.094 0.098 0.102 HE 3.94 ------ 4.25 0.155 ------ 0.167 L 0.80 ------ 1.20 0.031 ------ 0.047 Rev. A4 8/8 MAX APR. 18, 2003