00W148A Programmable negative supply IC BD6112FVM Description Dimension (Units : mm) BD6112FVM is a charge-pump negative supply IC with a built-in regulator. The charge-pump block inverts the positive supply voltage in the VBAT pin into a negative voltage, which generates from the NEGOUT pin. The regulator block stabilizes this negative voltage with low-noise that produces from the OUT pin. Output voltage values of this regulator can be controlled by voltage value inputted to the VIN pin and determined by OUT=--1.6 x VIN. 0.290.15 0.60.2 2.90.1 2.80.1 4.00.2 8 7 6 5 0.9Max. 0.750.05 0.080.05 0.475 1 2 3 4 0.145 +0.05 -0.03 0.22 +0.05 -0.04 0.65 0.08 M 0.08 S MSOP8 Features 1) Built-in high efficiency, inverting charge-pump 2) Built-in negative voltage regulator (low noise, output voltage variable) 3) Built-in standby SW (pull down resistance 1M) 4) Ultra small MSOP8 package Applications Small terminal devics such as cellular phones, PHS, and PDA etc. Other equipments driven by battery required for negative voltage. Absolute Maximum Ratings (Ta=25C) Parameter Limits Symbol VBAT -0.3 ~ +6.0 Maximum applied input voltage VIN -0.3 ~ +6.0 Power dissipation Pd Maximum applied supply voltage 350 * Unit V V mW Operating temperature range Topr -30 ~ +85 C Storage temperature range Tstg -55 ~ +125 C *Derating : 3.5mW/C for operation above Ta=25C February, 2001 Recommended Operating Conditions (Ta=25C) Parameter Power supply voltage Symbol Min. Typ. Max. Unit VBAT 2.5 3.6 5.5 V Electrical characteristics (Unless otherwise noted; Ta=25C, VBAT=3.6V, STBY=3.6V) Symbol Min. Typ. Max. Unit Circuit current Parameter IQ1 - 0.5 3 mA No load, VIN=1.25V Conditions Stand-by current IQ2 - - 5 A No load, VIN=0V, STBY=0V VIN=1.25V, IOUT=5mA <Regulator block> Output voltage 1 Vo -2.1 -2.0 -1.9 V Output voltage 2 Output ripple voltage Vo2 VRR Vo x 0.95 - Vo -70 Vo x 1.05 -60 V dBV VIN=0.5~1.8V, Vo=-1.6 x VIN,IOUT=5mA VIN=1.25V, IOUT=5mA IOMAX 10 - - mA VIN=1.25V, VOUTVo+0.1V Load regulation VOL - 2 40 mV VIN=1.25V, Io=0~5mA Line regulation VOI - 10 40 mV VBAT=3.0~6.0V, Io=5mA IIN - 0 2 A VIN=1.25V Oscillation frequency fosc - 120 - kHz Voltage conversion efficiency VCE - 97 - % 0.6 1.0 1.6 M 2.0 - - V -0.3 - 0.3 V Maximum output current VIN pin inflow current <Charge-pump block> Stand-by pin pull down resistance RSTBY Operating VIH Stand-by pin control voltage Non-operating VIL No load, NEGOUT monitor Application Circuit C+ 1 8 + GND + C4 1 CHARGE PUMP C1 VBAT 2 7 STBY 1 1M C- 3 6 OUT 1 1.6M NEGOUT C2 1 + 4 + - + 1M BD6112FVM 5 VIN + C3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document use silicon as a basic material. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.0