Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 34
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
v02.1109
HMC500LP3 / 500LP3E
General Description
Features
Functional Diagram
The HMC500LP3(E) is a high dynamic range
Vector Modulator RFICs which are targeted for RF
predistortion and feed-forward cancellation circuits,
as well as RF cancellation and beam forming amp-
litude/phase correction circuits. The I & Q ports of
the HMC500LP3(E) can be used to continuously vary
the phase and amplitude of RF signals by up to 360
degrees and 40 dB respectively, while supporting a
3 dB modulation bandwidth of 150 MHz. With an in-
put IP3 of +33 dBm and input noise  oor of -152 dBm/
Hz (at -10 dB maximum gain setting), the input IP3/
noise  oor ratio is 185 dB.
360° of Continuous Phase Control
Continuous Gain Control: 40 dB
-162 dBm/Hz Output Noise Floor
Input IP3: +33 dBm
16 Lead 3x3 mm SMT Package: 9mm
Typical Applications
The HMC500LP3(E) is ideal for:
• Wireless Infrastructure HPA &
MCPA Error Correction
• Pre-Distortion or Feed-Forward Linearization
• PCS, GSM and W-CDMA Systems
• Beam Forming or RF Cancellation Circuits
Electrical Speci cations, TA = +25° C, Vcc = +8V
Parameter Min. Typ. Max. Units
Frequency Range 1.8 - 2.2 GHz
Maximum Gain -14 -10 dB
Gain Variation Over Temperature 0.012 0.02 dB / °C
Gain Flatness Across Any 60 MHz Bandwidth 0.15 dB
Gain Range 40 dB
Input Return Loss 17 dB
Output Return Loss 15 dB
Input Power for 1dB Compression (P1dB) 13 16 dBm
Input Third Order Intercept (IP3) 33 dBm
Output Noise -162 dBm/Hz
Control Port Bandwidth (-3 dB) 150 MHz
Control Port Impedance 1.45k Ohms
Control Port Capacitance 0.22 pF
Control Voltage Range +0.5 to +2.5 Vdc
Group Delay Over 60 MHz Bandwidth 20 ps
Supply Current (Icq) 90 mA
Unless otherwise noted, measurements are made @ max. gain setting and 45˚ phase setting.
See application circuit for details.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 35
Input Return Loss vs. Temperature
Maximum Gain vs. Temperature Maximum Gain vs. Supply Voltage
Gain vs. Phase Settings @ F= 2 GHz
Phase vs. Phase Settings @ F= 2 GHz
vs. Various Gain Settings
Output Return Loss vs. Temperature
-20
-16
-12
-8
-4
0
1.7 1.8 1.9 2 2.1 2.2 2.3
+25C
+85C
-40C
GAIN (dB)
FREQUENCY (GHz)
-20
-16
-12
-8
-4
0
1.7 1.8 1.9 2 2.1 2.2 2.3
Vcc= 7.6V
Vcc= 8.0V
Vcc= 8.4V
GAIN (dB)
FREQUENCY (GHz)
-50
-40
-30
-20
-10
0
0 45 90 135 180 225 270 315 360
Max.
-5 dB
-10 dB
-20 dB
GAIN (dB)
PHASE SETTING (DEGREES)
0
45
90
135
180
225
270
315
360
0 45 90 135 180 225 270 315 360
Max.
-5 dB
-10 dB
-20 dB
PHASE (DEGREES)
PHASE SETTING (DEGREES)
-40
-35
-30
-25
-20
-15
-10
-5
0
1.7 1.8 1.9 2 2.1 2.2 2.3
+25C
+85C
-40C
RETURN LOSS (dB)
FREQUENCY (GHz)
-25
-20
-15
-10
-5
0
1.7 1.8 1.9 2 2.1 2.2 2.3
+25C
+85C
-40C
RETURN LOSS (dB)
FREQUENCY (GHz)
HMC500LP3 / 500LP3E
v02.1109
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 36
Input IP3 vs. Temperature
Output Noise vs. Temperature
Output Noise vs.
Phase Settings @ F= 2 GHz
Input P1dB vs. Temperature
Group Delay
-170
-168
-166
-164
-162
-160
1.7 1.8 1.9 2 2.1 2.2 2.3
+25 C
+85 C
-40 C
OUTPUT NOISE (dBm/Hz)
FREQUENCY (GHz)
-180
-175
-170
-165
-160
-155
-150
0 45 90 135 180 225 270 315 360
OUTPUT NOISE (dBm/Hz)
PHASE SETTING (DEGREES)
10
12
14
16
18
20
1.7 1.8 1.9 2 2.1 2.2 2.3
+25 C
+85 C
-40 C
INPUT P1dB (dBm)
FREQUENCY (GHz)
26
28
30
32
34
36
38
1.7 1.8 1.9 2 2.1 2.2 2.3
+25 C
+85 C
-40 C
INPUT IP3 (dBm)
FREQUENCY (GHz)
620
640
660
680
700
720
740
760
1.7 1.8 1.9 2 2.1 2.2 2.3
GROUP DELAY (ps)
FREQUENCY (GHz)
Linear Gain vs. Phase Setting
0
0.2
0.4
0.6
0.8
1
0
30
60
90
120
210
240
270
300
330
MAGNITUDE G/Gmax
HMC500LP3 / 500LP3E
v02.1109
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 37
Absolute Maximum Ratings
RF Input (Vcc = +8V) 27 dBm
Supply Voltage (Vcc) +10V
I & Q Input -0.5V to +5.0V
Channel Temperature (Tc) 135 °C
Continuous Pdiss (T = 85°C)
(Derate 25 mW/°C above 85°C) 1.25 W
Thermal Resistance (Rth)
(junction to ground paddle) 40 °C/W
Storage Temperature -65 to +150 °C
Operating Temperature -40 to +85 °C
Typical Supply Current vs. Vcc
Note:
Modulator will operate over full voltage range shown above.
Vcc (V) Icc (mA)
7.6 8 5
8.0 90
8.4 95
Outline Drawing
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Part Number Package Body Material Lead Finish MSL Rating Package Marking [3]
HMC500LP3 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] 500
XXXX
HMC500LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] 500
XXXX
[1] Max peak re ow temperature of 235 °C
[2] Max peak re ow temperature of 260 °C
[3] 4-Digit lot number XXXX
Package Information
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
HMC500LP3 / 500LP3E
v02.1109
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 38
Pin Description
Pin Number Function Description Interface Schematic
1, 4, 7, 8,
10 - 12, 14 N/C No connection. These pins may be connected to
RF/DC ground. Performance will not be affected
2, 3 IN, IN Differential RF inputs, 50 Ohms. Must be DC blocked.
5, 15 I In-phase control input. Pins 5 and 15 are redundant.
Either input can be used.
6, 16 Q Quadrature control input. Pins 6 and 16 are redundant.
Either input can be used.
9 RFOUT RF Output: Must be DC blocked.
13 Vcc Supply Voltage
GND Ground: Backside of package has exposed metal ground slug
which must be connected to RF/DC ground.
HMC500LP3 / 500LP3E
v02.1109
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 39
Gain and Phase control are applied through the I and Q control ports. For a given linear gain (G) and phase () setting, the
voltages applied to these ports in all measurements are calculated as follows:
Where Vmi and Vmq are the I and Q voltage settings corresponding to maximum isolation at room temperature and F = 2 GHz.
Note that G=10X and Gmax = 10Y where x = and y = . Nominally Vmi = Vmq = 1.5V, Gmax = 0.316.
IG Vmi V G
GCos(,) . max ()
θθ
=+10
QG Vmq V G
GSin(,) . max ()
θθ
=+10
Gain Setting dB ()
20
Max Gain Setting dB ()
20
Application Circuit
* Pins 15 & 16 are redundant I & Q inputs.
HMC500LP3 / 500LP3E
v02.1109
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 40
Evaluation PCB
The circuit board used in the  nal application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be con-
nected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation board should be mounted to an
appropriate heat sink. The evaluation circuit board
shown is available from Hittite upon request.
List of Materials for Evaluation PCB 106395 [1]
Item Description
J1 - J4 PCB Mount SMA Connector
J5 2 mm DC Header
C1 4.7 µF Capacitor, Tantalum
C2 - C5 1 nF Capacitor, 0402 Pkg.
T1 Balun, 1206 Pkg.
L1 330 nH Inductor, 0805 Pkg.
U1 HMC500LP3 / HMC500LP3E
Vector Modulator
PCB [2] 106388 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350, Er = 3.48
HMC500LP3 / 500LP3E
v02.1109
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
MODULATORS - VECTOR - SMT
10
10 - 41
Notes:
HMC500LP3 / 500LP3E
v02.1109
GaAs HBT VECTOR
MODULATOR 1.8 - 2.2 GHz
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Analog Devices Inc.:
HMC500LP3E HMC500LP3ETR 106395-HMC500LP3