NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS Bulk Typical application: deflection circuits in TV-sets and monitors (S-correction), resonant capacitor in electronic ballast and compact lamp, power factor correction and coupling capacitor in SMPS, timing, oscillator circuits. SERIES CODE: R75 Taped p 10 0.6 Od 0.05 15 p 27.5 0.8 p = 37.5 1.0 Fig. 2 12.70 Fig. 3 19.05 Fig. 1 P2 6.35 All dimensions are in mm. PART NUMBERING SYSTEM 1 2 3 4 GENERAL TECHNICAL DATA 5 6 7 [ ] R7 5 1. 2. 8 3. Series code Capacitance value in pico farads. First 2 digits are significant and 3rd digit indicates number of zeros. Capacitance tolerance 4. 5. D.C. voltage Packaging code 6. Lead spacing (mm) J = 5% B = bulk D = 7.5 N = 22.5 7. K = 10% A = ammo F = 10.0 R = 27.5 M = 20% R = reel Dielectric: Plates: polypropylene film aluminum layer deposited by evaporation under vacuum. Winding: non-inductive type Leads: tinned wire Protection: plastic case, epoxy resin filled. Box material is solvent resistant and flame retardant according to UL94 V0 Marking: manufacturer's logo, series (R75), dielectric code (MKP), capacitance, tolerance, D.C. rated voltage, manufacturing date code Climatic category: 55/100/56 IEC 60068-1 Operating temperature range: -55 to +105C Related documents: IEC 60384-16; CECC 31200 I = 15.0 W = 37.5 Lead length (mm) - (Applies to bulk packaging only. Omit for standard lead length 4-6mm.) L = 24-27 T = 3.5-4.0 V = 2.7-3.3 8. Internal code Note: Ammo-pack is the preferred packaging for taped version. NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS SERIES CODE: R75 single sided metallized polypropylene film 1 section (160Vdc) Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 4.0 9.0 10.5 7.5 100 32 E3 0.027F 0.033F 4.0 9.0 10.5 7.5 100 32 E3 0.039F 4.0 9.0 10.5 7.5 100 32 E3 0.047F 4.0 9.0 10.5 7.5 100 32 E3 0.056F 4.0 9.0 10.5 7.5 100 32 E3 0.068F 4.0 9.0 10.5 7.5 100 32 E3 0.082F 5.0 11.0 10.5 7.5 100 32 E3 5.0 11.0 10.5 7.5 100 32 E3 0.10F 6.0 12.0 10.5 7.5 100 32 E3 0.12F 6.0 12.0 10.5 7.5 100 32 E3 0.15F 25 E3 0.047F 4.0 9.0 13.0 10.0 80 25 E3 0.056F 4.0 9.0 13.0 10.0 80 25 E3 0.068F 4.0 9.0 13.0 10.0 80 25 E3 0.082F 4.0 9.0 13.0 10.0 80 5.0 11.0 13.0 10.0 80 25 E3 0.10F 5.0 11.0 13.0 10.0 80 25 E3 0.12F 5.0 11.0 13.0 10.0 80 25 E3 0.15F 6.0 12.0 13.0 10.0 80 25 E3 0.18F 5.0 11.0 18.0 15.0 100 32 E3 0.18F 5.0 11.0 18.0 15.0 100 32 E3 0.22F 6.0 12.0 18.0 15.0 100 32 E3 0.27F 6.0 12.0 18.0 15.0 100 32 E3 0.33F 7.5 13.5 18.0 15.0 100 32 E3 0.39F 7.5 13.5 18.0 15.0 100 32 E3 0.47F 8.5 14.5 18.0 15.0 100 32 E3 0.56F 8.5 14.5 18.0 15.0 100 32 E3 0.68F Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) 160Vdc/90Vac Part Number R75273-160-DR75333-160-DR75393-160-DR75473-160-DR75563-160-DR75683-160-DR75823-160-DR75104-160-DR75124-160-DR75154-160-DR75473-160-FR75563-160-FR75683-160-FR75823-160-FR75104-160-FR75124-160-FR75154-160-FR75184-160-FR75184-160-IR75224-160-IR75274-160-IR75334-160-IR75394-160-IR75474-160-IR75564-160-IR75684-160-I- Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 7.0 16.0 26.5 22.5 60 19 E3 0.82F 7.0 16.0 26.5 22.5 60 19 E3 1.0F 8.5 17.0 26.5 22.5 60 19 E3 1.2F 10.0 18.5 26.5 22.5 60 19 E3 1.5F 10.0 18.5 26.5 22.5 60 19 E3 1.8F 10.0 20.0 32.0 27.5 50 16 E3 2.2F 11.0 20.0 32.0 27.5 50 16 E3 2.7F 13.0 22.0 32.0 27.5 50 16 E3 *3.3F 13.0 22.0 32.0 27.5 50 16 E3 *3.9F 15.0 24.5 32.0 27.5 50 16 E3 *4.7F 14.0 28.0 32.0 27.5 50 16 E3 *5.6F 18.0 33.0 32.0 27.5 50 16 E3 *6.8F 18.0 33.0 32.0 27.5 50 16 E3 *8.2F 16 E3 *10.0F 22.0 37.0 32.0 27.5 50 11 E3 12.0F 19.0 32.0 41.5 37.5 35 11 E3 15.0F 20.0 40.0 41.5 37.5 35 11 E3 18.0F 20.0 40.0 41.5 37.5 35 11 E3 22.0F 24.0 44.0 41.5 37.5 35 Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) * 160Vdc/90Vac Part Number R75824-160-NR75105-160-NR75125-160-NR75155-160-NR75185-160-NR75225-160-RR75275-160-RR75335-160-RR75395-160-RR75475-160-RR75565-160-RR75685-160-RR75825-160-RR75106-160-RR75126-160-WR75156-160-WR75186-160-WR75226-160-W- These values are available in pitch 37.5mm upon request. All dimensions are in mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage waveform and in any case it cannot exceed the value given in the above table. The dv/dt test is carried out at 2 times the above values. NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS SERIES CODE: R75 single sided metallized polypropylene film 1 section (250Vdc) Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 4.0 9.0 10.5 7.5 225 115 E3 0.015F 4.0 9.0 10.5 7.5 225 115 E3 0.018F 4.0 9.0 10.5 7.5 225 115 E3 0.022F 5.0 11.0 10.5 7.5 225 115 E3 0.027F 5.0 11.0 10.5 7.5 225 115 E3 0.033F 6.0 12.0 10.5 7.5 225 115 E3 0.039F 6.0 12.0 10.5 7.5 225 115 E3 0.047F 6.0 12.0 10.5 7.5 225 115 E3 0.056F 4.0 9.0 13.0 10.0 125 65 E3 0.022F 4.0 9.0 13.0 10.0 125 65 E3 0.027F 4.0 9.0 13.0 10.0 125 65 E3 0.033F 4.0 9.0 13.0 10.0 125 65 E3 0.039F 5.0 11.0 13.0 10.0 125 65 E3 0.047F 5.0 11.0 13.0 10.0 125 65 E3 0.056F 6.0 12.0 13.0 10.0 125 65 E3 0.068F 6.0 12.0 13.0 10.0 125 65 E3 0.082F 6.0 12.0 13.0 10.0 125 65 E3 0.10F 5.0 11.0 18.0 15.0 200 100 E3 0.12F 5.0 11.0 18.0 15.0 200 100 E3 0.15F 5.0 11.0 18.0 15.0 200 100 E3 0.18F 5.0 11.0 18.0 15.0 200 100 E3 0.22F 6.0 12.0 18.0 15.0 200 100 E3 0.27F 6.0 12.0 18.0 15.0 200 100 E3 0.33F 7.5 13.5 18.0 15.0 200 100 E3 0.39F 7.5 13.5 18.0 15.0 200 100 E3 0.47F 7.5 13.5 18.0 15.0 200 100 E3 0.56F 8.5 14.5 18.0 15.0 200 100 E3 0.68F 10.0 16.0 18.0 15.0 200 100 E3 0.82F 10.0 16.0 18.0 15.0 200 100 E3 1.0F Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) 250Vdc/160Vac Part Number R75153-250-DR75183-250-DR75223-250-DR75273-250-DR75333-250-DR75393-250-DR75473-250-DR75563-250-DR75223-250-FR75273-250-FR75333-250-FR75393-250-FR75473-250-FR75563-250-FR75683-250-FR75823-250-FR75104-250-FR75124-250-IR75154-250-IR75184-250-IR75224-250-IR75274-250-IR75334-250-IR75394-250-IR75474-250-IR75564-250-IR75684-250-IR75824-250-IR75105-250-I- Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 6.0 15.0 26.5 22.5 125 63 E3 0.39F 6.0 15.0 26.5 22.5 125 63 E3 0.47F 6.0 15.0 26.5 22.5 125 63 E3 0.56F 6.0 15.0 26.5 22.5 125 63 E3 0.68F 7.0 16.0 26.5 22.5 125 63 E3 0.82F 7.0 16.0 26.5 22.5 125 63 E3 1.0F 8.5 17.0 26.5 22.5 125 63 E3 1.2F 10.0 18.5 26.5 22.5 125 63 E3 1.5F 10.0 18.5 26.5 22.5 125 63 E3 1.8F 11.0 20.0 26.5 22.5 125 63 E3 2.2F 9.0 17.0 32.0 27.5 100 50 E3 1.2F 9.0 17.0 32.0 27.5 100 50 E3 1.5F 9.0 17.0 32.0 27.5 100 50 E3 1.8F 10.0 20.0 32.0 27.5 100 50 E3 2.2F 11.0 20.0 32.0 27.5 100 50 E3 2.7F *3.3F 13.0 22.0 32.0 27.5 100 50 E3 *3.9F 13.0 22.0 32.0 27.5 100 50 E3 *4.7F 15.0 24.5 32.0 27.5 100 50 E3 *5.6F 14.0 28.0 32.0 27.5 100 50 E3 *6.8F 18.0 33.0 32.0 27.5 100 50 E3 *8.2F 18.0 33.0 32.0 27.5 100 50 E3 *10.0F 22.0 37.0 32.0 27.5 100 50 E3 *12.0F 22.0 37.0 32.0 27.5 100 50 E3 50 E3 15.0F 20.0 40.0 41.5 37.5 35 50 E3 18.0F 20.0 40.0 41.5 37.5 35 50 E3 22.0F 24.0 44.0 41.5 37.5 35 Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) * 250Vdc/160Vac Part Number R75394-250-NR75474-250-NR75564-250-NR75684-250-NR75824-250-NR75105-250-NR75125-250-NR75155-250-NR75185-250-NR75225-250-NR75125-250-RR75155-250-RR75185-250-RR75225-250-RR75275-250-RR75335-250-RR75395-250-RR75475-250-RR75565-250-RR75685-250-RR75825-250-RR75106-250-RR75126-250-RR75156-250-WR75186-250-WR75226-250-W- These values are available in pitch 37.5mm upon request. All dimensions are in mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage waveform and in any case it cannot exceed the value given in the above table. The dv/dt test is carried out at 2 times the above values. NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS SERIES CODE: R75 single sided metallized polypropylene film 1 section (400Vdc) Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 4.0 9.0 10.5 7.5 250 200 E3 5600F 4.0 9.0 10.5 7.5 250 200 E3 6800F 4.0 9.0 10.5 7.5 250 200 E3 8200F 4.0 9.0 10.5 7.5 250 200 E3 0.010F 4.0 9.0 10.5 7.5 250 200 E3 0.012F 5.0 11.0 10.5 7.5 250 200 E3 0.015F 5.0 11.0 10.5 7.5 250 200 E3 0.018F 6.0 12.0 10.5 7.5 250 200 E3 0.022F 6.0 12.0 10.5 7.5 250 200 E3 0.027F 4.0 9.0 13.0 10.0 175 140 E3 0.010F 4.0 9.0 13.0 10.0 175 140 E3 0.012F 4.0 9.0 13.0 10.0 175 140 E3 0.015F 4.0 9.0 13.0 10.0 175 140 E3 0.018F 5.0 11.0 13.0 10.0 175 140 E3 0.022F 5.0 11.0 13.0 10.0 175 140 E3 0.027F 6.0 12.0 13.0 10.0 175 140 E3 0.033F 6.0 12.0 13.0 10.0 175 140 E3 0.039F 6.0 12.0 13.0 10.0 175 140 E3 0.047F 5.0 11.0 18.0 15.0 300 240 E3 0.068F 5.0 11.0 18.0 15.0 300 240 E3 0.082F 5.0 11.0 18.0 15.0 300 240 E3 0.10F 6.0 12.0 18.0 15.0 300 240 E3 0.12F 6.0 12.0 18.0 15.0 300 240 E3 0.15F 7.5 13.5 18.0 15.0 300 240 E3 0.18F 7.5 13.5 18.0 15.0 300 240 E3 0.22F 8.5 14.5 18.0 15.0 300 240 E3 0.27F 10.0 16.0 18.0 15.0 300 240 E3 0.33F 10.0 16.0 18.0 15.0 300 240 E3 0.39F Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) 400Vdc/220Vac** Part Number R75562-400-DR75682-400-DR75822-400-DR75103-400-DR75123-400-DR75153-400-DR75183-400-DR75223-400-DR75273-400-DR75103-400-FR75123-400-FR75153-400-FR75183-400-FR75223-400-FR75273-400-FR75333-400-FR75393-400-FR75473-400-FR75683-400-IR75823-400-IR75104-400-IR75124-400-IR75154-400-IR75184-400-IR75224-400-IR75274-400-IR75334-400-IR75394-400-I- Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 6.0 15.0 26.5 22.5 180 144 E3 0.27F 6.0 15.0 26.5 22.5 180 144 E3 0.33F 7.0 16.0 26.5 22.5 180 144 E3 0.39F 7.0 16.0 26.5 22.5 180 144 E3 0.47F 8.5 17.0 26.5 22.5 180 144 E3 0.56F 0.68F 10.0 18.5 26.5 22.5 180 144 E3 0.82F 10.0 18.5 26.5 22.5 180 144 E3 11.0 20.0 26.5 22.5 180 144 E3 1.0F 9.0 17.0 32.0 27.5 130 104 E3 0.56F 9.0 17.0 32.0 27.5 130 104 E3 0.68F 9.0 17.0 32.0 27.5 130 104 E3 0.82F 10.0 20.0 32.0 27.5 130 104 E3 1.0F *1.2F 11.0 20.0 32.0 27.5 130 104 E3 *1.5F 13.0 22.0 32.0 27.5 130 104 E3 *1.8F 13.0 22.0 32.0 27.5 130 104 E3 *2.2F 15.0 24.5 32.0 27.5 130 104 E3 *2.7F 14.0 28.0 32.0 27.5 130 104 E3 *3.3F 18.0 33.0 32.0 27.5 130 104 E3 *3.9F 18.0 33.0 32.0 27.5 130 104 E3 *4.7F 22.0 37.0 32.0 27.5 130 104 E3 *5.6F 22.0 37.0 32.0 27.5 130 104 E3 19.0 32.0 41.5 37.5 70 56 E3 6.8F 20.0 40.0 41.5 37.5 70 56 E3 8.2F 24.0 44.0 41.5 37.5 70 56 E3 10F Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) * ** 400Vdc/220Vac** Part Number R75274-400-NR75334-400-NR75394-400-NR75474-400-NR75564-400-NR75684-400-NR75824-400-NR75105-400-NR75564-400-RR75684-400-RR75824-400-RR75105-400-RR75125-400-RR75155-400-RR75185-400-RR75225-400-RR75275-400-RR75335-400-RR75395-400-RR75475-400-RR75565-400-RR75685-400-WR75825-400-WR75106-400-W- These values are available in pitch 37.5mm upon request. Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors. All dimensions are in mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage waveform and in any case it cannot exceed the value given in the above table. The dv/dt test is carried out at 2 times the above values. NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS SERIES CODE: R75 single sided metallized polypropylene film 1 section (630Vdc) Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 4.0 9.0 10.5 7.5 300 380 E3 1000F 4.0 9.0 10.5 7.5 300 380 E3 1200F 4.0 9.0 10.5 7.5 300 380 E3 1500F 4.0 9.0 10.5 7.5 300 380 E3 1800F 4.0 9.0 10.5 7.5 300 380 E3 2200F 4.0 9.0 10.5 7.5 300 380 E3 2700F 4.0 9.0 10.5 7.5 300 380 E3 3300F 4.0 9.0 10.5 7.5 300 380 E3 3900F 4.0 9.0 10.5 7.5 300 380 E3 4700F 5.0 11.0 10.5 7.5 300 380 E3 5600F 5.0 11.0 10.5 7.5 300 380 E3 6800F 5.0 11.0 10.5 7.5 300 380 E3 8200F 6.0 12.0 10.5 7.5 300 380 E3 0.010F 6.0 12.0 10.5 7.5 300 380 E3 0.012F 4.0 9.0 13.0 10.0 250 315 E3 1000F 4.0 9.0 13.0 10.0 250 315 E3 1200F 4.0 9.0 13.0 10.0 250 315 E3 1500F 4.0 9.0 13.0 10.0 250 315 E3 1800F 4.0 9.0 13.0 10.0 250 315 E3 2200F 4.0 9.0 13.0 10.0 250 315 E3 2700F 4.0 9.0 13.0 10.0 250 315 E3 3300F 4.0 9.0 13.0 10.0 250 315 E3 3900F 4.0 9.0 13.0 10.0 250 315 E3 4700F 4.0 9.0 13.0 10.0 250 315 E3 5600F 4.0 9.0 13.0 10.0 250 315 E3 6800F 4.0 9.0 13.0 10.0 250 315 E3 8200F 5.0 11.0 13.0 10.0 250 315 E3 0.010F 5.0 11.0 13.0 10.0 250 315 E3 0.012F 6.0 12.0 13.0 10.0 250 315 E3 0.015F 6.0 12.0 13.0 10.0 250 315 E3 0.018F Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) 630Vdc/250Vac** Part Number R75102-630-DR75122-630-DR75152-630-DR75182-630-DR75222-630-DR75272-630-DR75332-630-DR75392-630-DR75472-630-DR75562-630-DR75682-630-DR75822-630-DR75103-630-DR75123-630-DR75102-630-FR75122-630-FR75152-630-FR75182-630-FR75222-630-FR75272-630-FR75332-630-FR75392-630-FR75472-630-FR75562-630-FR75682-630-FR75822-630-FR75103-630-FR75123-630-FR75153-630-FR75183-630-F- All dimensions are in mm. * ** These values are available in pitch 37.5mm upon request. Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors. Note: Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 5.0 11.0 18.0 15.0 400 504 E3 0.022F 0.027F 5.0 11.0 18.0 15.0 400 504 E3 0.033F 5.0 11.0 18.0 15.0 400 504 E3 0.039F 5.0 11.0 18.0 15.0 400 504 E3 0.047F 5.0 11.0 18.0 15.0 400 504 E3 0.056F 5.0 11.0 18.0 15.0 400 504 E3 0.068F 6.0 12.0 18.0 15.0 400 504 E3 0.082F 6.0 12.0 18.0 15.0 400 504 E3 7.5 13.5 18.0 15.0 400 504 E3 0.10F 7.5 13.5 18.0 15.0 400 504 E3 0.12F 8.5 14.5 18.0 15.0 400 504 E3 0.15F 0.18F 10.0 16.0 18.0 15.0 400 504 E3 0.22F 10.0 16.0 18.0 15.0 400 504 E3 6.0 15.0 26.5 22.5 250 315 E3 0.12F 6.0 15.0 26.5 22.5 250 315 E3 0.15F 7.0 16.0 26.5 22.5 250 315 E3 0.18F 7.0 16.0 26.5 22.5 250 315 E3 0.22F 8.5 17.0 26.5 22.5 250 315 E3 0.27F 0.33F 10.0 18.5 26.5 22.5 250 315 E3 0.39F 10.0 18.5 26.5 22.5 250 315 E3 0.47F 11.0 20.0 26.5 22.5 250 315 E3 0.56F 11.0 20.0 26.5 22.5 250 315 E3 0.39F 11.0 20.0 32.0 27.5 180 227 E3 0.47F 11.0 20.0 32.0 27.5 180 227 E3 0.56F 11.0 20.0 32.0 27.5 180 227 E3 *0.68F 11.0 20.0 32.0 27.5 180 227 E3 *0.82F 13.0 22.0 32.0 27.5 180 227 E3 *1.0F 13.0 22.0 32.0 27.5 180 227 E3 *1.2F 15.0 24.5 32.0 27.5 180 227 E3 *1.5F 14.0 28.0 32.0 27.5 180 227 E3 *1.8F 18.0 33.0 32.0 27.5 180 227 E3 *2.2F 18.0 33.0 32.0 27.5 180 227 E3 *2.7F 22.0 37.0 32.0 27.5 180 227 E3 *3.3F 22.0 37.0 32.0 27.5 180 227 E3 20.0 40.0 41.5 37.5 90 113 E3 3.9F 20.0 40.0 41.5 37.5 90 113 E3 4.7F 24.0 44.0 41.5 37.5 90 113 E3 5.6F Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) 630Vdc/250Vac** Part Number R75223-630-IR75273-630-IR75333-630-IR75393-630-IR75473-630-IR75563-630-IR75683-630-IR75823-630-IR75104-630-IR75124-630-IR75154-630-IR75184-630-IR75224-630-IR75124-630-NR75154-630-NR75184-630-NR75224-630-NR75274-630-NR75334-630-NR75394-630-NR75474-630-NR75564-630-NR75394-630-RR75474-630-RR75564-630-RR75684-630-RR75824-630-RR75105-630-RR75125-630-RR75155-630-RR75185-630-RR75225-630-RR75275-630-RR75335-630-RR75395-630-WR75475-630-WR75565-630-W- If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage waveform and in any case it cannot exceed the value given in the above table. The dv/dt test is carried out at 2 times the above values. NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS SERIES CODE: R75 single sided metallized polypropylene film single sided metallized polypropylene film 1 section (1000Vdc) Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 5.0 11.0 18.0 15.0 450 900 E3 0.012F 0.015F 5.0 11.0 18.0 15.0 450 900 E3 0.018F 5.0 11.0 18.0 15.0 450 900 E3 0.022F 5.0 11.0 18.0 15.0 450 900 E3 0.027F 6.0 12.0 18.0 15.0 450 900 E3 0.033F 6.0 12.0 18.0 15.0 450 900 E3 0.039F 7.5 13.5 18.0 15.0 450 900 E3 0.047F 7.5 13.5 18.0 15.0 450 900 E3 0.056F 8.5 14.5 18.0 15.0 450 900 E3 0.068F 8.5 14.5 18.0 15.0 450 900 E3 0.082F 10.0 16.0 18.0 15.0 450 900 E3 0.068F 6.0 15.0 26.5 22.5 300 600 E3 0.082F 7.0 16.0 26.5 22.5 300 600 E3 7.0 16.0 26.5 22.5 300 600 E3 0.10F 8.5 17.0 26.5 22.5 300 600 E3 0.12F 0.15F 10.0 18.5 26.5 22.5 300 600 E3 0.18F 10.0 18.5 26.5 22.5 300 600 E3 0.22F 11.0 20.0 26.5 22.5 300 600 E3 0.22F 10.0 20.0 32.0 27.5 200 400 E3 *0.27F 11.0 20.0 32.0 27.5 200 400 E3 *0.33F 13.0 22.0 32.0 27.5 200 400 E3 *0.39F 13.0 22.0 32.0 27.5 200 400 E3 *0.47F 15.0 24.5 32.0 27.5 200 400 E3 *0.56F 15.0 24.5 32.0 27.5 200 400 E3 *0.68F 18.0 33.0 32.0 27.5 200 400 E3 *0.82F 18.0 33.0 32.0 27.5 200 400 E3 *1.0F 18.0 33.0 32.0 27.5 200 400 E3 *1.2F 22.0 37.0 32.0 27.5 200 400 E3 19.0 32.0 41.5 37.5 150 300 E3 1.5F 20.0 40.0 41.5 37.5 150 300 E3 1.8F 20.0 40.0 41.5 37.5 150 300 E3 2.2F 24.0 44.0 41.5 37.5 150 300 E3 2.7F Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) 1000Vdc/250Vac** 2 sections (1250Vdc) Part Number R75123-1000-IR75153-1000-IR75183-1000-IR75223-1000-IR75273-1000-IR75333-1000-IR75393-1000-IR75473-1000-IR75563-1000-IR75683-1000-IR75823-1000-IR75683-1000-NR75823-1000-NR75104-1000-NR75124-1000-NR75154-1000-NR75184-1000-NR75224-1000-NR75224-1000-RR75274-1000-RR75334-1000-RR75394-1000-RR75474-1000-RR75564-1000-RR75684-1000-RR75824-1000-RR75105-1000-RR75125-1000-RR75155-1000-WR75185-1000-WR75225-1000-WR75275-1000-W- All dimensions are in mm. * ** These values are available in pitch 37.5mm upon request. Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors. Note: Rated Cap. Max Max K0 dv/dt B H L P (V/s) (V2/s) 5.0 11.0 18.0 15.0 1300 3400 E3 1500F 5.0 11.0 18.0 15.0 1300 3400 E3 1800F 5.0 11.0 18.0 15.0 1300 3400 E3 2200F 5.0 11.0 18.0 15.0 1300 3400 E3 2700F 5.0 11.0 18.0 15.0 1300 3400 E3 3300F 5.0 11.0 18.0 15.0 1300 3400 E3 3900F 5.0 11.0 18.0 15.0 1300 3400 E3 4700F 5.0 11.0 18.0 15.0 1300 3400 E3 5600F 5.0 11.0 18.0 15.0 1300 3400 E3 6800F 6.0 12.0 18.0 15.0 1300 3400 E3 8200F 0.010F 6.0 12.0 18.0 15.0 1300 3400 E3 0.012F 7.5 13.5 18.0 15.0 1300 3400 E3 0.015F 7.5 13.5 18.0 15.0 1300 3400 E3 0.018F 8.5 14.5 18.0 15.0 1300 3400 E3 0.022F 10.0 16.0 18.0 15.0 1300 3400 E3 0.027F 10.0 16.0 18.0 15.0 1300 3400 E3 0.018F 6.0 15.0 26.5 22.5 700 1800 E3 0.022F 6.0 15.0 26.5 22.5 700 1800 E3 0.027F 7.0 16.0 26.5 22.5 700 1800 E3 0.033F 7.0 16.0 26.5 22.5 700 1800 E3 0.039F 8.5 17.0 26.5 22.5 700 1800 E3 0.047F 10.0 18.5 26.5 22.5 700 1800 E3 0.056F 10.0 18.5 26.5 22.5 700 1800 E3 0.068F 11.0 20.0 26.5 22.5 700 1800 E3 *0.082F 10.0 20.0 32.0 27.5 500 1300 E3 *0.10F 11.0 20.0 32.0 27.5 500 1300 E3 *0.12F 13.0 22.0 32.0 27.5 500 1300 E3 *0.15F 13.0 22.0 32.0 27.5 500 1300 E3 *0.18F 14.0 28.0 32.0 27.5 500 1300 E3 *0.22F 18.0 33.0 32.0 27.5 500 1300 E3 *0.27F 18.0 33.0 32.0 27.5 500 1300 E3 *0.33F 18.0 33.0 32.0 27.5 500 1300 E3 *0.39F 22.0 37.0 32.0 27.5 500 1300 E3 *0.47F 22.0 37.0 32.0 27.5 500 1300 E3 900 E3 0.56F 20.0 40.0 41.5 37.5 360 900 E3 0.68F 20.0 40.0 41.5 37.5 360 900 E3 0.82F 24.0 44.0 41.5 37.5 360 Tolerance: J ( 5%); K (10%); M (20%) Packaging code: B (bulk); A (ammo); R (reel) Lead length (mm): L (24-27); T (3.5-4.0); V (2.7-3.3) Omit for standard (4-6) 1250Vdc/500Vac** Part Number R75152-1250-IR75182-1250-IR75222-1250-IR75272-1250-IR75332-1250-IR75392-1250-IR75472-1250-IR75562-1250-IR75682-1250-IR75822-1250-IR75103-1250-IR75123-1250-IR75153-1250-IR75183-1250-IR75223-1250-IR75273-1250-IR75183-1250-NR75223-1250-NR75273-1250-NR75333-1250-NR75393-1250-NR75473-1250-NR75563-1250-NR75683-1250-NR75823-1250-RR75104-1250-RR75124-1250-RR75154-1250-RR75184-1250-RR75224-1250-RR75274-1250-RR75334-1250-RR75394-1250-RR75474-1250-RR75564-1250-WR75684-1250-WR75824-1250-W- If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage waveform and in any case it cannot exceed the value given in the above table. The dv/dt test is carried out at 2 times the above values. NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS SERIES CODE: R75 ELECTRICAL CHARACTERISTICS TEST METHOD AND PERFORMANCE Rated voltage (VR): 160Vdc - 250Vdc - 400Vdc 630Vdc - 1000Vdc for 1 section 1250Vdc for 2 sections Rated temperature (TR): +85C Voltage derating vs. temperature: The following decreasing factor has to be applied on the rated voltage: +85C to +105C: 2.00% per C for VR (d.c.) +85C to +105C: 1.25% per C for VR (a.c.) Capacitance range: 1000F to 22F 1500F to 0.82F Damp heat, steady state: Test conditions Temperature: Relative humidity (RH): Test duration: Performance Capacitance change (C/C): 2% Capacitance values: E 12 series (IEC 60063 Norm) 10x10 at 1kHz Insulation resistance: 50% of initial limit Voltage applied: Performance Capacitance tolerances (measured at 1 kHz): 5% (J); 10% (K); 20% (M) 7.5 8 10 9 15 10 22.5 18 27.5 18 DF change (tg): 37.5 20 Dissipation factor (DF): -4 tgx10 at +25C 5C KHz C0.1F 0.1F<C1F 1 4 5 10 6 8 100 25 Insulation resistance: Test conditions Temperature: Voltage charge time: Voltage charge: Performance 1<C4.7F 6 C>4.7F 10 -4 10x10 at 10kHz for C1F Insulation resistance: 50% of initial limit Resistance to soldering heat: Test conditions Solder bath temperature: +260C 5C Dipping time (with heat screen): 10 s 1 s Performance Capacitance change (C/C): 1% -4 10x10 at 10kHz for C1F 10x10-4 at 1kHz for C>1F +25C 5C 1 min 100Vdc Insulation resistance: 5 1 x 10 M for C 0.33F (5 x 10 M)* 30000 s for C > 0.33F (15000 s)* *Typical value Test voltage between terminations: 1.6xVR applied for 2 s at +25C 5C 1.25xVR 10x10-4 at 1kHz for C>1F DF change (tg): 5 +85C 2C 2000 h Capacitance change (C/C): 3% Total self-inductance (L): (lead length ~2mm) Pitch (mm) L (nH) -4 DF change (tg): Endurance: Test conditions Temperature: Test duration: 1 section 2 sections (1250Vdc) +40C 2C 93% 2% 56 days initial limit Long term stability (after two years): Storage: standard environmental conditions (see general information). Performance Capacitance change (C/C): 0.5% NISSEI-ARCOTRONICS R75 MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR D.C. and PULSE APPLICATIONS SERIES CODE: R75 MAX. VOLTAGE (Vrms) VERSUS FREQUENCY (sinusoidal waveform / Th 40C) Note: p (pitch) in mm