Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
Advanced AMS1501
Monolithic 1.5A LOW DROPOUT VOLTAGE REGULATORS
Systems
FEATURES APPLICATIONS
Adjustable or Fixed Output High Current Regulators
1.5V, 2.5V, 2.85V, 3.0V, 3.3V, 3.5V and 5.0V Post Regulators for Switching Supplies
Output Current of 1.5A Adjustable Power Supply
Low Dropout, 500mV at 1.5A Output Current Notebook/Personal Computer Supplies
Fast Transient Response
Remote Sense
GENERAL DESCRIPTION
The
The AMS1501 series of adjustable and fixed low dropout voltage regulators are designed to provide 1.5A output current to
power the new generation of microprocessors. The dropout voltage of the device is 100mV at light loads and rising to 500mV
at maximum output current. A second low current input voltage 1V or greater then the output voltage is required to achieve
this dropout. The AMS1501 can also be used as a single supply device.
New features have been added to the AMS1501: a remote Sense pin is brought out virtually eliminating output voltage
variations due to load changes. The typical load regulation, measured at the Sense pin, for a load current step of 100mA to
1.5A is less than 1mV.
The AMS1501 series has fast transient response. The Adjust pin is brought out on fixed devices. To further improve the
transient response the addition of a small capacitor on the Adjust pin is recommended.
The AMS1501 series are ideal for generating power supplies of 2V to 3V where both 5V and 3.3V supplies are available.
The AMS1501 devices are offered in 5 lead TO-220 and TO-263 (plastic DD) packages and in the 7 lead TO-220 package.
ORDERING INFORMATION: PIN CONNECTIONS
PACKAGE TYPE OPERATING JUNCTION
5 LEAD TO-263 5 LEAD TO-220 7 LEAD TO-220 TEMPERATURE RANGE
AMS1501CM AMS1501CT AMS1501CT-1.5 0 to 125° C
AMS1501CM-1.5 AMS1501CT-1.5 AMS1501CT-2.5 0 to 125° C
AMS1501CM-2.5 AMS1501CT-2.5 AMS1501CT-2.85 0 to 125° C
AMS1501CM-2.85 AMS1501CT-2.85 AMS1501CT-3.0 0 to 125° C
AMS1501CM-3.0 AMS1501CT-3.0 AMS1501CT-3.3 0 to 125° C
AMS1501CM-3.3 AMS1501CT-3.3 AMS1501CT-3.5 0 to 125° C
AMS1501CM-3.5 AMS1501CT-3.5 AMS1501CT-5.0 0 to 125° C
AMS1501CM-5.0 AMS1501CT-5.0 0 to 125° C
5
4
3
2
1
VPOWER
VCONTROL
OUTPUT
ADJUST/GND
SENSE
FRONT VIEW
5 LEAD TO-220
7
6
5
4
3
2
1
NC
Vpower
ADJUST
OUTPUT
Vcontrol
GND
SENSE
7 LEAD TO-220
FRONT VIEW
5
4
3
2
1
Vpower
Vcontrol
OUTPUT
ADJUST/GND
SENSE
FRONT VIEW
5 LEAD TO-263
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
ABSOLUTE MAXIMUM RATINGS (Note 1)
VPOWER Input Voltage 7V Soldering information
VCONTROL Input Voltage 13V Lead Temperature (10 sec) 300°C
Operating
Junction Temperature Range
Thermal Resistance
Control Section 0°C to 125°C TO-220 package ϕ
JA
= 50°C/W
Power Transistor 0°C to 150°C TO-263 package ϕ
JA
= 30°C/W*
Storage temperature - 65°C to +150°C* With package soldering to 0.5in
2
copper area over backside ground
plane or internal power plane ϕ JA can vary from 20°C/W to >40°C/W
depending on mounting technique.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at ILOAD = 0 mA, and TJ = +25°C unless otherwise specified.
Parameter Device Conditions Min Typ Max Units
Reference Voltage AMS1501 VCONTROL = 2.75V, VPOWER =2V, ILOAD = 10mA
VCONTROL = 2.7V to 12V, VPOWER =3.3V to 5.5V,
ILOAD = 10mA to 1.5A
1.243
1.237 1.250
1.250 1.258
1.263 V
V
Output Voltage AMS1501-1.5 VCONTROL = 4V, VPOWER =2.V, ILOAD = 0mA
VCONTROL = 3V, VPOWER =2.3V, ILOAD = 0mA to 1.5A 1.491
1.485 1.500
1.500 1.509
1.515 V
V
AMS1501-2.5 VCONTROL = 5V, VPOWER =3.3V, ILOAD = 0mA
VCONTROL = 4V, VPOWER =3.3V, ILOAD = 0mA to 1.5A 2.485
2.475 2.500
2.500 2.515
2.525 V
V
AMS1501-2.85 VCONTROL = 5.35V, VPOWER =3.35V, ILOAD = 0mA
VCONTROL = 4.4V, VPOWER =3.7V, ILOAD = 0mA to 1.5A 2.821
2.833 2.850
2.850 2.879
2.867 V
V
AMS1501-3.0 VCONTROL = 5.5V, VPOWER =3.5V, ILOAD = 0mA
VCONTROL = 4.5V, VPOWER =3.8V, ILOAD = 0mA to 1.5A 2.982
2.970 3.000
3.000 3.018
3.030 V
V
AMS1501-3.3 VCONTROL = 5.8V, VPOWER =3.8V, ILOAD = 0mA
VCONTROL = 4.8V, VPOWER =4.1V, ILOAD = 0mA to 1.5A 3.280
3.235 3.300
3.300 3.320
3.333 V
V
AMS1501-3.5 VCONTROL = 6V, VPOWER =4V, ILOAD = 0mA
VCONTROL = 5V, VPOWER =4.3V, ILOAD = 0mA to 1.5A 3.479
3.430 3.500
3.500 3.521
3.535 V
V
AMS1501-5.0 VCONTROL = 7.5V, VPOWER =5.5V, ILOAD = 0mA
VCONTROL = 6.5V, VPOWER =5.8V, ILOAD = 0mA to 1.5A 4.930
4.950 5.000
5.000 5.030
5.050 V
V
Line Regulation AMS1501/-1.5/-2.5/
-2.85/ -3.0/-3.3/-3.5/-5.0
ILOAD = 10 mA , 1.5V (VCONTROL - VOUT) 12V
0.8V (VPOWER - VOUT) 5.5V
1 3 mV
Load Regulation AMS1501/-1.5/-2.5/
-2.85/-3.0/-3.3/-3.5/-5.0
VCONTROL = VOUT + 2.5V, VPOWER =VOUT + 0.8V,
ILOAD = 10mA to 1.5A
1 5 mV
Minimum Load
Current AMS1501 VCONTROL = 5V, VPOWER =3.3V, VADJ = 0V (Note 3) 5 10 mA
Control Pin Current
(Note 4)
AMS1501/-1.5/-2.5/
-2.85/-3.0/-3.3/-3.5/-5.0
VCONTROL = VOUT + 2.5V, VPOWER =VOUT + 0.8V,
ILOAD = 10mA to 1.5A
10 16 mA
Ground Pin Current
(Note 4)
AMS1501-1.5/-2.5/
-2.85/-3.0/-3.3/-3.5/-5.0
VCONTROL = VOUT + 2.5V, VPOWER =VOUT + 0.8V,
ILOAD = 10mA to 1.5A
6 10 mA
Adjust Pin Current AMS1501 VCONTROL = 2.75V, VPOWER = 2.05V, ILOAD = 10mA 50 120 µA
Current Limit AMS1501/-1.5/-2.5/
-2.85/-3.0/-3.3/-3.5/-5.0
(VIN - VOUT) = 5V 1.5 2.0 2.8 A
Ripple Rejection AMS1501/-1.5/-2.5/
-2.85/-3.0/-3.3/-3.5/-5.0
VCONTROL = VPOWER = VOUT + 2.5V, VRIPPLE = 1VP-P
ILOAD = 1A 60 80 dB
Thermal Regulation AMS1501 TA = 25°C, 30ms pulse 0.002 0.020 %W
Thermal Resistance
Junction-to-Case T Package: Control Circuitry/ Power Transistor
M Package: Control Circuitry/ Power Transistor
0.65/2.70
0.65/2.70
°C/W
°C/W
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at IOUT = 0 mA, and TJ = +25°C unless otherwise specified.
Parameter Device Conditions Min Typ Max Units
Dropout Voltage Note 2
Control Dropout
(VCONTROL - VOUT)AMS1501/-1.5/-2.5/
-2.85/-3.0/-3.3/-3.5/-5.0
VPOWER =VOUT + 0.8V, ILOAD = 10mA
VPOWER =VOUT + 0.8V, ILOAD = 1.5A
1.00
1.15
1.15
1.30
V
V
Power Dropout
(VPOWER - VOUT)AMS1501/-1.5/-2.5/
-2.85/-3.0/-3.3/-3.5/-5.0
VCONTROL =VOUT + 2.5V, ILOAD = 10mA
VCONTROL =VOUT + 2.5V, ILOAD = 1.5A
.10
.45
0.17
.50
V
V
Parameters identified with boldface type apply over the full operating temperature range.
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the
Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed.
Note 2: Unless otherwise specified VOUT = VSENSE. For the adjustable device VADJ = 0V.
Note 3: The dropout voltage for the AMS1501 is caused by either minimum control voltage or minimum power voltage. The specifications represent the minimum
input/output voltage required to maintain 1% regulation.
Note 4: For the adjustable device the minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor divider
used to set the output voltage is selected to meet the minimum load current requirement.
Note 5: The control pin current is the drive current required for the output transistor. This current will track output current with a ratio of about 1:100. The
minimum value is equal to the quiescent current of the device.
PIN FUNCTIONS
Sense (Pin 1): This pin is the positive side of the
reference voltage for the device. With this pin it is
possible to Kelvin sense the output voltage at the load.
Adjust (Pin 2/5): This pin is the negative side of the
reference voltage for the device. Adding a small bypass
capacitor from the Adjust pin to ground improves the
transient response. For fixed voltage devices the Adjust
pin is also brought out to allow the user to add a bypass
capacitor.
GND (Pin 2, 7-Lead only): For fixed voltage devices this
is the bottom of the resistor divider that sets the output
voltage.
VPOWER (Pin 5/6): This pin is the collector to the power
device of the AMS1501. The output load current is
supplied through this pin. The voltage at this pin must
be between 0.1V and 0.8V greater than the output
voltage for the device to regulate.
V
CONTROL
(Pin 4/3): This pin is the supply pin for the
control circuitry of the device. The current flow into
this pin will be about 1% of the output current. The
voltage at this pin must be 1.3V or greater than the
output voltage for the device to regulate.
Output (Pin 3/4): This is the power output of the
device.
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
APPLICATION HINTS
The AMS1501 is designed to make use of multiple power
supplies, existing in most systems, to reduce the dropout voltage.
One of the advantages of the two supply approach is maximizing
the efficiency.
The second supply is at least 1V greater than output voltage and
is providing the power for the control circuitry and supplies the
drive current to the NPN output transistor. This allows the NPN
to be driven into saturation; thereby reducing the dropout voltage
by a VBE compared to conventional designs. For the control
voltage the current requirement is small equal to about 1% of the
output current or approximately 15mA for a 1.5A load. Most of
this current is drive current for the NPN output transistor. This
drive current becomes part of the output current. The maximum
voltage on the Control pin is 13V. The maximum voltage at the
Power pin is 7V. Ground pin current for fixed voltage devices is
typical 6mA and is constant as a function of load. Adjust pin
current for adjustable devices is 60µA at 25°C and varies
proportional to absolute temperature.
The improved frequency compensation of AMS1501 permits the
use of capacitors with very low ESR. This is critical in addressing
the needs of modern, low voltage high sped microprocessors.
Output voltage tolerances are tighter and include transient
response as part of the specification. Designed to meet the fast
current load step requirements, the AMS1501 also saves total
cost by needing less output capacitance to maintain regulation.
Careful design of the AMS1501 has eliminated any supply
sequencing issues associated with a dual supply system. The
output voltage will not turn on until both supplies are operating.
If the control voltage comes up first, the output current will be
limited to a few milliamperes until the power input voltage comes
up. If power input comes up first the output will not turn on at all
until the control voltage comes up. The output can never come up
unregulated. By tying the control and power inputs together the
AMS1501 can also be operated as a single supply device. In
single supply operation the dropout will be determined by the
minimum control voltage.
The new features of the AMS1501 require additional pins over
the traditional 3-terminal regulator. Both the fixed and adjustable
versions have remote sense pins, permitting very accurate
regulation of output voltage at the load, rather than at the
regulator. As a result, over an output current range of 100mA to
1.5A with a 2.5V output, the typical load regulation is less than
1mV. For the fixed voltages the adjust pin is brought out allowing
the user to improve transient response by bypassing the internal
resistor divider. Optimum transient response is provided using a
capacitor in the range of 0.1µF to 1µF for bypassing the Adjust
pin. The value chosen will depend on the amount of output
capacitance in the system.
In addition to the enhancements mentioned, the reference
accuracy has been improved by a factor of two with a guaranteed
initial tolerance of ±0.6% at 25°C. This device can hold 1%
accuracy over the full temperature range and load current range,
guaranteed, when combined with ratiometrically accurate internal
divider resistors and operating with an input/output differential of
well under 1V.
Typical applications for the AMS1501 include 3.3V to 2.5V
conversion with a 5V control supply, 5V to 4.2V conversion with
a 12V control supply or 5V to3.6V conversion with a 12V control
supply. Capable of 1.5A of output current with a maximum
dropout of 0.8V the AMS1501 also has a fast transient response
that allows it to handle large current changes. The device is fully
protected against overcurrent and overtemperature conditions.
Grounding and Output Sensing
The AMS1501 allows true Kelvin sensing for both the high and
low side of the load. As a result the voltage regulation at he load
can be easily optimized. Voltage drops due to parasitic
resistances between the regulator and the load can be placed
inside the regulation loop of the AMS1501. The advantages of
remote sensing are illustrated in figures 1 through 3.
Figure 1 shows the device connected as a conventional 3 terminal
regulator with the Sense lead connected directly to the output of
the device. R
P
is the parasitic resistance of the connections
between the device and the load. Typically R
P
is made up of the
PC traces and /or connector resistances (in the case of a modular
regulator) between the regulator and the load. Trace A of figure 3
illustrates the effect of RP. Very small resistances cause
significant load regulation steps.
Figure 2 shows the device connected to take advantage of the
remote sense feature. The Sense pin and the top of the resistor
divider are connected to the top of the load; the bottom of the
resistor divider is connected to the bottom of the load. R
P
is now
connected inside the regulation loop of the AMS1501 and for
reasonable values of R
P
the load regulation at the load will be
negligible. The effect on output regulation can be seen in trace B
of figure 3.
CONTROL
POWER SENSE
AMS1501
OUTPUT
ADJ
LOAD
+
-
VOUT
RP
RP
R1
R2
5V
3.3V
Figure 1. Conventional Load Sensing
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
APPLICATION HINTS
CONTROL
POWER SENSE
AMS1501
OUTPUT
ADJ
LOAD
+
-
VOUT
RP
RP
R1
R2
5V
3.3V
Figure 2. Remote Load Sensing
(IOUT)(RP)
TIME
VOUT
FIGURE 1
VOUT
FIGURE 2
IOUT
Figure 3. Remote Sensing Improves Load Regulation
Voltage drops due to R
P
are not eliminated; they will add to the
dropout voltage of the regulator regardless of whether they are
inside or outside the regulation loop. The AMS1501 can control
the voltage at the load as long as the input-output voltage is
greater than the total of the dropout voltage of the device plus the
voltage drop across RP.
Stability
The circuit design used in the AMS1501 series requires the use of
an output capacitor as part of the device frequency compensation.
The addition of 150µF aluminum electrolytic or a 22µF solid
tantalum on the output will ensure stability for all operating
conditions. For best frequency response use capacitors with an
ESR of less than 1.
In order to meet the transient requirements of the load larger
value capacitors are needed. Tight voltage tolerances are required
in the power supply. To limit the high frequency noise generated
by the load high quality bypass capacitors must be used. In order
to limit parasitic inductance (ESL) and resistance (ESR) in the
capacitors to acceptable limits, multiple small ceramic capacitors
in addition to high quality solid tantalum capacitors are required.
When the adjustment terminal is bypassed to improve the ripple
rejection, the requirement for an output capacitor increases. The
Adjust pin is brought out on the fixed voltage device specifically
to allow this capability. To ensure good transient response with
heavy load current changes capacitor values on the order of
100µF are used in the output of many regulators. To further
improve stability and transient response of these devices larger
values of output capacitor can be used.
The modern systems generate large high frequency current
transients. The load current step contains higher order frequency
components than the output coupling network must handle until
the regulator throttles to the load current level. Because they
contain parasitic resistance and inductance, capacitors are not
ideal elements. These parasitic elements dominate the change in
output voltage at the beginning of a transient load step change.
The ESR of the output capacitors produces an instantaneous step
in output voltage (V=I)(ESR). The ESL of the output
capacitors produces a droop proportional to the rate of change of
the output current (V= L)(I/t). The output capacitance
produces a change in output voltage proportional to the time until
the regulator can respond (V=t) (I/C). Figure 4 illustrates
these transient effects.
CAPACITANCE
EFFECTS
ESR
EFFECTS
ESL
EFFECTS
POINT AT WHICH REGULATOR
TAKES CONTROL
SLOPE, V/t = I/C
Figure 4.
Output Voltage
The AMS1501 series develops a 1.25V reference voltage
between the Sense pin and the Adjust pin (Figure5). Placing a
resistor between these two terminals causes a constant current to
flow through R1 and down through R2 to set the overall output
voltage. In general R1 is chosen so that this current is the
specified minimum load current of 10mA.The current out of the
Adjust pin is small, typically 50µA and it adds to the current
from R1. Because I
ADJ
is very small it needs to be considered
only when very precise output voltage setting is required. For
best regulation the top of the resistor divider should be connected
directly to the Sense pin.
CONTROL
POWER OUTPUT
AMS1501
SENSE
ADJ R1
R2
VOUT
VREF
VPOWER
IADJ
50
µ
A
+
++
VCONTROL
VOUT = VREF (1+ R2/R1)+IADJR2
Figure 5. Setting Output Voltage
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
APPLICATION HINTS
Protection Diodes
Unlike older regulators, the AMS1501 family does not need any
protection diodes between the adjustment pin and the output and
from the output to the input to prevent die over-stress. Internal
resistors are limiting the internal current paths on the AMS1501
adjustment pin, therefore even with bypass capacitors on the
adjust pin no protection diode is needed to ensure device safety
under short-circuit conditions. The Adjust pin can be driven on a
transient basis ±7V with respect to the output without any device
degradation.
Diodes between the Output pin and V
POWER
pin are not usually
needed. Microsecond surge currents of 25A to 50A can be
handled by the internal diode between the Output pin and VPOWER
pin of the device. In normal operations it is difficult to get those
values of surge currents even with the use of large output
capacitances. If high value output capacitors are used, such as
1000µF to 5000µF and the V
POWER
pin is instantaneously shorted
to ground, damage can occur. A diode from output to input is
recommended, when a crowbar circuit at the input of the
AMS1501 is used (Figure 6). Normal power supply cycling or
even plugging and unplugging in the system will not generate
current large enough to do any damage.
CONTROL
POWER OUTPUT
AMS1501
SENSE
ADJ R1
R2
VOUT
VPOWER
+
++
D2*D1*
VCONTROL
Figure 6. Optional Clamp Diodes Protect Against
Input Crowbar Circuits
If the AMS1501 is connected as a single supply device with the
control and power input pins shorted together the internal diode
between the output and the power input pin will protect the
control input pin. As with any IC regulator, none the protection
circuitry will be functional and the internal transistors will break
down if the maximum input to output voltage differential is
exceeded.
Thermal Considerations
The AMS1501 series have internal power and thermal limiting
circuitry designed to protect the device under overload conditions.
However maximum junction temperature ratings should not be
exceeded under continuous normal load conditions. Careful
consideration must be given to all sources of thermal resistance
from junction to ambient, including junction-to-case, case-to-heat
sink interface and heat sink resistance itself.
Thermal resistance specification for both the Control Section and
the Power Transistor are given in the electrical characteristics.
The thermal resistance of the Control section is given as
0.65°C/W and junction temperature of the Control section can
run up to 125°C. The thermal resistance of the Power section is
given as 2.7°C/W and junction temperature of the Power section
can run up to 150°C. Due to the thermal gradients between the
power transistor and the control circuitry there is a significant
difference in thermal resistance between the Control and Power
sections.
Virtually all the power dissipated by the device is dissipated in
the power transistor. The temperature rise in the power transistor
will be greater than the temperature rise in the Control section
making the thermal resistance lower in the Control section. At
power levels below 12W the temperature gradient will be less
than 25°C and the maximum ambient temperature will be
determined by the junction temperature of the Control section.
This is due to the lower maximum junction temperature in the
Control section. At power levels above 12W the temperature
gradient will be greater than 25°C and the maximum ambient
temperature will be determined by the Power section. In both
cases the junction temperature is determined by the total power
dissipated in the device. For most low dropout applications the
power dissipation will be less than 12W.
The power in the device is made up of two components: the
power in the output transistor and the power in the drive circuit.
The power in the control circuit is negligible.
The power in the drive circuit is equal to:
PDRIVE = (VCONTROL - VOUT)(ICONTROL)
where I
CONTROL
is equal to between I
OUT
/100(typ) and
IOUT/58(max).
The power in the output transistor is equal to:
POUTPUT = (VPOWER -VOUT)(IOUT)
The total power is equal to:
PTOTAL = PDRIVE + POUTPUT
Junction-to-case thermal resistance is specified from the IC
junction to the bottom of the case directly below the die. This is
the lowest resistance path for the heat flow. In order to ensure the
best possible thermal flow from this area of the package to the
heat sink proper mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A thermally
conductive spacer can be used, if the case of the device must be
electrically isolated, but its added contribution to thermal
resistance has to be considered.
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
TYPICAL PERFORMANCE CHARACTERISTICS
00.5 11.5 00.5 11.5 00.5 11.5
0
20
40
60
80
100
120
140
CONTROL PIN CURRENT (mA)
0
2
1
MINMUM CONTROL VOLTAGE
(V
CONTROL
- V
OUT
)(V)
0
0.5
1.0
MINIMUM POWER VOLTAGE
OUTPUT CURRENT (A) OUTPUT CURRENT (A) OUTPUT CURRENT (A)
Control Pin Current vs
Output Current Minimum Control Voltage Dropout Voltage -
Minimum Power Voltage
TYPICAL
DEVICE T
J
= 25° CT
J
= 125° C T
J
= 125° C
T
J
= 25° C
Reference Voltage vs
Temperature
1.242
1.244
1.246
1.248
1.250
1.252
1.254
1.256
1.258
-50 -25 0 25 50 75 100 125 150
REFERENCE VOLTAGE (V)
TEMPERATURE (° C)
Load Current Step Response
50µ/DIV
VOUT
50µV/DIV
1.5A
400mA
LOAD
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted.
5 LEAD TO-220 PLASTIC PACKAGE (T)
5 LEAD TO-263 PLASTIC PACKAGE (M)
0.330-0.370
(8.382-9.398)
0.090-0.110
(2.286-2.794)
0.390-0.415
(9.906-10.541) 0.165-0.180
(4.191-4.572) 0.045-0.055
(1.143-1.397)
0.095-0.115
(2.413-2.921)
0.013-0.023
(0.330-0.584)
T (TO-220 ) AMS DRW# 042194
0.147-0.155
(3.734-3.937)
DIA
0.230-0.270
(5.842-6.858)
0.460-0.500
(11.684-12.700)
0.570-0.620
(14.478-15.748)
0.520-0.570
(13.208-14.478)
0.980-1.070
(24.892-27.178)
0.028-0.038
(0.711-0.965)
0.060
(1.524)
TYP
0.390-0.415
(9.906-10.541)
0.330-0.370
(8.382-9.398)
0.057-0.077
(1.447-1.955)
0.165-0.180
(4.191-4.572) 0.045-0.055
(1.143-1.397)
0.095-0.115
(2.413-2.921)
0.90-0.110
(2.29-2.79)
0.013-0.023
(0.330-0.584)
0.108
(2.74)
TYP
(0.102 )
+0.203
-0.102
0.004 +0.008
-0.004
M (DD5) AMS DRW#042192R1
(5.05-5.54 )
0.199-0.218
0.032
(0.81)
TYP
Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140
AMS1501
PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted (Continued).
7 LEAD TO-220 PLASTIC PACKAGE (T)
0.330-0.370
(8.382-9.398)
0.040-0.060
(1.016-1.524)
0.390-0.415
(9.906-10.541) 0.165-0.180
(4.191-4.572) 0.045-0.055
(1.143-1.397)
0.095-0.115
(2.413-2.921)
0.013-0.023
(0.330-0.584)
T (TO-220 ) AMS DRW# 042291
0.147-0.155
(3.734-3.937)
DIA
0.230-0.270
(5.842-6.858)
0.460-0.500
(11.684-12.700)
0.570-0.620
(14.478-15.748)
0.520-0.620
(13.208-14.224)
0.980-1.070
(24.892-27.178)
0.026-0.036
(0.660-0.914)