NDT SERIES Isolated 3W Wide Input Dual Output DC-DC Converters SELECTION GUIDE 1 Nominal Rated Input Output Voltage Voltage Order Code NDTD2412 NDTD2415 NDTD4812 NDTD4815 (V) 24 24 48 48 Output Current Input Current Min Load3 Full Load Full Load (mA) 31 25 31 25 (mA) 125 100 125 100 (mA) 156 155 77 77 (V) 12 15 12 15 MTTF4 (%) 79 80 81 81 (pF) 30 30 30 30 kHrs 2075 2080 2090 2045 INPUT CHARACTERISTICS 1 FEATURES Parameter Industry Standard Footprint 24V input types Voltage Range 48V input types Reflected Ripple 24V input types with 10F at input Current 48V input types with 10F at input 1kVDC Isolation Dual Isolated Output Short Circuit Protection Low Profile 24 Pin Case Efficiency to 81% Power Density 0.90W/cm 3 2:1 Wide Input Range 24V & 48V Input 12V & 15V Output Footprint 4.73cm2 UL 94V-0 Package Materials Operating Temperature Range -40C to 85C Load and Line Regulation <1% on Both Outputs No Heatsink Required Internal SMD Construction Fully Encapsulated Custom Solutions Available DESCRIPTION The NDT series is a range of low profile DCDC converters offering dual outputs over a 2:1 input voltage range. All parts deliver 3W output power up to 85C without heatsinking. A flyback oscillator design with isolated feedback is used to give regulation over the full operating range of 25% to 100% of full load. It is strongly recommended that external capacitors be used on input and output to guarantee performance over full load and input voltage range (see application notes for guidance). The plastic case is rated to UL 94V-0 and encapsulant to UL 94V-1and the connection pins are formed from a tin plated alloy 42 leadframe. www.dc-dc.com Conditions MIN TYP MAX 18 36 24 48 200 125 36 75 250 150 Units TYP MAX Units 3 W 1 5 % 0.15 0.5 % 0.2 0.5 % 15 30 mV rms 90 150 mV p-p 2.1 3.0 % VDC mA p-p OUTPUT CHARACTERISTICS 1 Parameter Conditions MIN Rated Power Voltage Set Point Accuracy With external input/output capacitors, refer to recommended test circuit Low line to high line, Line Regulation with external input/output capacitors, refer to recommended test circuit 25% load to 100% load, Load Regulation with external input/output capacitors, refer to recommended test circuit BW = 20Hz to 300kHz Ripple With external input/output capacitors, refer to recommended test circuit BW = DC to 20MHz Ripple & Noise With external input/output capacitors, refer to recommended test circuit % voltage change on negative output Cross when positive load varies from 12% to Regulation 50% with negative load fixed at 50% ABSOLUTE MAXIMUM RATINGS Short circuit protection over temperature range and input voltage range Input Voltage, 24V types Input Voltage, 48V types Lead temperature 1.5mm from case for 10 seconds Minimum Load continuous 40V 80V 300C 25% of rated output ISOLATION CHARACTERISTICS1 Parameter Conditions Isolation Test Voltage Resistance Flash tested for 1 second Viso=1KVDC MIN TYP MAX 1000 1 Units VDC G GENERAL CHARACTERISTICS 1 Parameter Conditions MIN TYP MAX Units Switching Frequency 100% load V IN nominal 25% load V IN nominal 100 410 125 500 150 590 kHz MIN TYP MAX Units 85 130 C C C ENVIRONMENTAL1 Parameter Conditions Operation Storage Case Temperature Above Ambient 100% Load - 40 - 50 28 1 Specifications typical at T A =25C, nominal input voltage and rated output current unless otherwise specified. 2 Measured at full load with external input/output capacitors, refer to test circuit. 3 A lower load is entirely safe but higher levels of output ripple will be experienced. 4 Calculated using MIL-HDBK-217F with nominal input voltage at full load. NDT SERIES Isolated 3W Wide Input Dual Output DC-DC Converters TERMINOLOGY PIN CONNECTIONS 24 Pin DIL (top view) LINE REGULATION The percentage change in output voltage between low input voltage and high input voltage, measured with fixed output load ie. A 5V output part with an output voltage of 5.05V @ high input voltage and 5.03V @ low input voltage would have a line regulation of 0.4%. line regulation = -V IN 2 23 +VIN -V IN 3 22 +VIN Common 9 16 Common 11 14 +V OUT VOUT (Low Input V) -V OUT (High Input V) x100% VOUT (Nominal Input V) Where VOUT (Nominal Input V) is 5V. APPLICATION NOTES EXTERNAL CAPACITANCE Although these converters will work without external capacitors, they ar e necessary in order to guarantee the full parametric performance over the full line and load range. All parts have been tested and characterised using the following values and test circuit Value CIN 10F, 200V -VOUT TEST CIRCUIT COUT 47F, 25V +VOUT VIN COUT CIN NDT 0V COUT GND -VOUT PACKAGING DETAILS Order Code Packaging Style QTY NDTDXXXX Tube 15 TUBE OUTLINE DIMENSIONS 0.6570.022 (16.700.55) MECHANICAL DIMENSIONS 0.6570.031 (16.700.80) 1.270(32.26) 0.100(2.54) 0.8150.022 (20.700.55) 0.200 (5.08) 0.2170.001 (5.500.25) 0.2680.022 6.800.55 0.0310.006 (0.800.15) Tube Length: 20.4720.079(520mm2mm) Tube Material: Antistatic coated clear pvc. 0.577(14.66) RECOMMENDED FOOTPRINT DETAILS 0.275(7.00) 0.185(4.70) 0.145(3.70) 0.012(0.30) 0.008(0.20) 0.033(0.84) 0.021(0.54) 0.185 (4.70) Weight: 6.5g 0.600(15.25)Max 0.900(22.86) Unless otherwise stated all dimensions in inches 0.010 (mm 0.25mm). C&D Technologies (NCL) Limited reserve the right to alter or improve the specification, internal design or manufacturing process at any time, without notice. Please check with your supplier or visit our web site to ensure that you have the current and complete specification for your product before use. (c) C&D Technologies (NCL) Limited 2002 NDC NDT.1 No part of this publication may be copied, transmitted or stored in a retrieval system or reproduced in any way including, but not limited to, photography, photocopy, magnetic or other recording means, without prior written permission from C&D Technologies (NCL) Limited. Instructions for use are available from www.dc-dc.com C&D Technologies (NCL) Ltd Tanners Drive, Blakelands North Milton Keynes MK14 5BU, England Tel: +44 (0)1908 615232 Fax:+44 (0)1908 617545 email: info@cdtechno-ncl.com www: http://www.dc-dc.com 0.057(1.45) O 0.051(1.30) 0.100(2.54) 8 Holes All pins on a 0.100(2.54) pitch and within 0.010(0.25) of true position. C&D Technologies Inc. 3400 E Britannia Drive, Tucson, Arizona 85706, USA Tel: +1 (800) 547-2537 Fax: +1 (520) 741-4598 email: sales@cdtechno.com 0.100 (2.54) O0.1