HM-65162/883 TM 2kx8 Asynchronous CMOS Static RAM March 1997 Features Description * This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. The HM-65162/883 is a CMOS 2048 x 8 Static Random Access Memory manufactured using the Intersil Advanced SAJI V process. The device utilizes asynchronous circuit design for fast cycle time and ease of use. The pinout is the JEDEC 24 pin DIP, and 32 pad 8-bit wide standard which allows easy memory board layouts flexible to accommodate a variety of industry standard PROMs, RAMs, ROMs and EPROMs. The HM-65162/883 is ideally suited for use in microprocessor based systems with its 8-bit word length organization. The convenient output enable also simplifies the bus interface by allowing the data outputs to be controlled independent of the chip enable. Gated inputs lower operating current and also eliminate the need for pull-up or pull-down resistors. * Fast Access Time . . . . . . . . . . . . . . . . . . . 70/90ns Max * Low Standby Current. . . . . . . . . . . . . . . . . . . . 50A Max * Low Operating Current . . . . . . . . . . . . . . . . . 70mA Max * Data Retention at 2.0V . . . . . . . . . . . . . . . . . . . 20A Max * TTL Compatible Inputs and Outputs * JEDEC Approved Pinout (2716, 6116 Type) * No Clocks or Strobes Required * Wide Temperature Range . . . . . . . . . . -55oC to +125oC * Equal Cycle and Access Time * Single 5V Supply * Gated Inputs - No Pull-Up or Pull-Down Resistors Required Ordering Information 70ns/20A 90ns/40A HM1-65162B/883 HM1-65162/883 HM4-65162B/883 HM4-65162/883 90ns/300A TEMP. RANGE -55oC to 125oC -55oC to 125oC HM1-65162C/883 - PACKAGE PKG. NO. CERDIP F24.6 CLCC J32.A Pinouts NC NC NC VCC NC NC HM-65162/883 (CLCC) TOP VIEW A7 HM-65162/883 (CERDIP) TOP VIEW 4 3 2 1 32 31 30 PIN A7 1 24 VCC A6 2 23 A8 A6 5 29 A8 A5 3 22 A9 A5 6 A0 - A10 4 21 W 28 A9 A4 A3 5 20 G A4 7 27 NC E A2 6 19 A10 A3 8 26 W 9 25 G DQ0 9 16 DQ6 A0 11 23 E DQ1 10 15 DQ5 NC 12 22 DQ7 DQ2 11 14 DQ4 13 21 DQ6 GND 12 13 DQ3 14 15 16 17 18 19 20 GND DQ0 DQ5 24 A10 DQ4 A1 10 NC 17 DQ7 DQ3 18 E 8 DQ2 7 A0 DQ1 A1 A2 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2002. All Rights Reserved 188 NC DESCRIPTION No Connect Address Input Chip Enable/Power Down VSS/GND Ground DQ0 - DQ7 Data In/Data Out VCC Power (+5V) W Write Enable G Output Enable FN3001.1 HM-65162/883 Functional Diagram A1 A A2 A3 A4 A5 A6 A7 ROW ADDRESS BUFFER 7 A ROW DECODER 128 128 X 128 MEMORY ARRAY 7 1 OF 8 128 E COLUMN DECODER AND DATA INPUT / OUTPUT (X8) 4 G A 4 A COLUMN ADDRESS BUFFER W A0 189 A8 A9 A10 8 DQ0 THRU DQ7 HM-65162/883 Absolute Maximum Ratings Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V Input, Output or I/O Voltage . . . . . . . . . . . GND -0.3V to VCC +0.3V Typical Derating Factor . . . . . . . . . .1.5mA/MHz Increase in ICCOP ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 Thermal Resistance JA JC CERDIP Package . . . . . . . . . . . . . . . . 48oC/W 8oC/W CLCC Package . . . . . . . . . . . . . . . . . . 66oC/W 12oC/W Maximum Storage Temperature Range . . . . . . . . .-65oC to +150oC Maximum Junction Temperature. . . . . . . . . . . . . . . . . . . . . . +175oC Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . +300oC Die Characteristics Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26000 Gates CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC Input Low Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +0.8V Chip Enable High/Low Time . . . . . . . . . . . . . . . . . . . . . . . 40ns (Min) Input High Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . -2.2V to VCC Data Retention Supply Voltage . . . . . . . . . . . . . . . . . . . 2.0V to 4.5V Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . 40ns Max TABLE 1. 65162/883 DC ELECTRICAL PERFORMANCE SPECIFICATIONS Device Guaranteed and 100% Tested PARAMETER (NOTE 1) CONDITIONS SYMBOL LIMITS GROUP A SUBGROUPS TEMPERATURE MIN MAX UNITS 2.4 - V VOH1 VCC = 4.5V, IO = -1.0mA 1, 2, 3 -55oC TA +125oC Low Level Output Voltage VOL VCC = 4.5V, IO = 4.0mA 1, 2, 3 -55oC TA +125oC - 0.4 V High Impedance Output Leakage Current IIOZ VCC = 5.5V, G = 2.2V, or E = 2.2V, VI/O = GND or VCC 1, 2, 3 -55oC TA +125oC -1.0 1.0 A VCC = 5.5V, VI = GND or VCC 1, 2, 3 -55oC TA +125oC -1.0 1.0 A HM-65162B/883, IO = 0mA, VCC = 5.5V, E = VCC -0.3V 1, 2, 3 -55oC TA +125oC - 50 A HM-65162/883, IO = 0mA, VCC = 5.5V, E = VCC - 0.3V 1, 2, 3 -55oC TA +125oC - 100 A HM-65162C/883, IO = 0mA, VCC = 5.5V, E = VCC - 0.3V 1, 2, 3 -55oC TA +125oC - 900 A High Level Output Voltage Input Leakage Current Standby Supply Current II ICCSB1 Standby Supply Current ICCSB VCC = 5.5V, IO = 0mA, E = 2.2V 1, 2, 3 -55oC TA +125oC - 8 mA Operating Supply Current ICCOP VCC = 5.5V, G = 5.5V, (Note 2), f = 1MHz, E = 0.8V 1, 2, 3 -55oC TA +125oC - 70 mA Enable Supply Current ICCEN VCC = 5.5V, IO = 0mA, E = 0.8V 1, 2, 3 -55oC TA +125oC - 70 mA Data Retention Supply Current ICCDR HM-65162B/883, IO = 0mA, VCC = 2.0V, E = VCC - 0.3V 1, 2, 3 -55oC TA +125oC - 20 A HM-65162/883, IO = 0mA, VCC = 2.0V, E = VCC - 0.3V 1, 2, 3 -55oC TA +125oC - 40 A HM-65162C/883, IO = 0mA, VCC = 2.0V, E = VCC - 0.3V 1, 2, 3 -55oC TA +125oC - 300 A 7, 8A, 8B -55oC TA +125oC - - - Functional Test FT VCC = 4.5V (Note 3) NOTES: 1. All voltages referenced to device GND. 2. Input pulse levels: 0.8V to VCC - 2.0V; Input rise and fall times: 5ns (max); Input and output timing reference level: 1.5V; Output load: 1 TTL gate equivalent, CL = 50pF (min) - for CL greater than 50pF, access time by 0.15ns per pF. 3. TAVQV = TELQV + TAVEL. 190 HM-65162/883 TABLE 2. HM-65162/883 AC ELECTRICAL PERFORMANCE SPECIFICATIONS Device Guaranteed and 100% Tested. LIMITS PARAMETER SYMBOL (NOTES 1, 2) CONDITIONS GROUP A SUBGROUPS TEMPERATURE HM-65162B /883 HM-65162 /883 HM-65162C /883 MIN MAX MIN MAX MIN MAX UNITS Read/Write/ Cycle Time (1) TAVAX VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 70 - 90 - 90 - ns Address Access Time (2) TAVQV VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC - 70 - 90 - 90 ns Chip Enable Access Time (3) TELQV VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC - 70 - 90 - 90 ns Output Enable Access Time (5) TGLQV VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC - 50 - 65 - 65 ns Chip Selection to End of Write (11) TELWH VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 45 - 55 - 55 - ns Address Setup Time (12) TAVWL VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 10 - 10 - 10 - ns Write Enable Pulse Write (13) TWLWH VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 40 - 55 - 55 - ns Write Enable Read Setup Time (14) TWHAX VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 10 - 10 - 10 - ns Data Setup Time (17) TDVWH VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 30 - 30 - 30 - ns Data Hold Time (18) TWHDX VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 10 - 15 - 15 - ns Write Enable Pulse Setup Time (20) TWLEH VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 40 - 55 - 55 - ns Chip Enable Data Setup Time (21) TDVEH VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 30 - 30 - 30 - ns Address Valid to End of Write (22) TAVWH VCC = 4.5V and 5.5V 9, 10, 11 -55oC TA +125oC 50 - 65 - 65 - ns NOTES: 1. All voltages referenced to device GND. 2. Input pulse levels: 0.8V to VCC -2.0V; Input rise and fall times: 5ns (max); Input and output timing reference level: 1.5V; Output load: 1 TTL gate equivalent, CL = 50pF (min) - for CL greater than 50pF, access time is derated by 0.15ns per pF. 3. TAVQV = TELQV + TAVEL. 191 HM-65162/883 TABLE 3. HM-65162/883 ELECTRICAL PERFORMANCE SPECIFICATIONS, AC AND DC LIMITS PARAMETER SYMBOL Input Capacitance CIN I/O Capacitance CI/O HM65162B/883 HM65162/883 HM65162C/883 NOTES TEMPERATURE MIN MAX MIN MAX MIN MAX UNITS VCC = Open, F = 1MHz, All Measurements Referenced To Device Ground 1, 2 +25oC - 10 - 10 - 10 pF 1, 3 +25oC - 8 - 8 - 8 pF VCC = Open, F = 1MHz, All Measurements Referenced To Device Ground 1, 2 +25oC - 12 - 12 - 12 pF 1, 3 +25oC - 10 - 10 - 10 pF CONDITIONS Chip Enable to Output ON (4) TELQX VCC = 4.5V and 5.5V 1 -55oC TA +125oC 5 - 0 - 5 - ns Output Enable to Output ON (6) TGLQX VCC = 4.5V and 5.5V 1 -55oC TA +125oC 5 - 5 - 5 - ns Chip Enable High to Output In High Z (7) TEHQZ VCC = 4.5V and 5.5V 1 -55oC TA +125oC - 35 - 50 - 50 ns Output Disable to Output in High Z (8) TGHQZ VCC = 4.5V and 5.5V 1 -55oC TA +125oC - 35 - 40 - 40 ns Output Hold from Address Change (9) TAVQX VCC = 4.5V and 5.5V 1 -55oC TA +125oC 5 - 5 - 5 - ns Write Enable to Output in High Z (16) TWLQZ VCC = 4.5V and 5.5V 1 -55oC TA +125oC - 40 - 50 - 50 ns Write Enable High to Output ON (19) TWHQX VCC = 4.5V and 5.5V 1 -55oC TA +125oC 0 - 0 - 0 - ns VCC = 4.5V, IO = -100A 1 -55oC TA +125oC VCC 0.4V - VCC 0.4V - VCC 0.4V - V Output High Voltage VOH2 NOTES: 1. The parameters listed in Table 3 are controlled via design or process parameters and are not directly tested. These parameters are characterized upon initial design release and upon design changes which would affect these characteristics. 2. Applies to DIP device types only. 3. Applies to LCC device types only. TABLE 4. APPLICABLE SUBGROUPS CONFORMANCE GROUPS METHOD SUBGROUPS Initial Test 100%/5004 - Interim Test 100%/5004 1, 7, 9 PDA 100%/5004 1 Final Test 100%/5004 2, 3, 7, 8A, 8B, 10, 11 Group A Samples/5005 1, 2, 3, 7, 8A, 8B, 9, 10, 11 Groups C & D Samples/5005 1, 7, 9 192 HM-65162/883 Timing Waveforms (1) TAVAX (2) TAVQV ADDRESS (8) TGHQZ G (5) TGLQV E (7) TEHQZ (6) TGLQX (3) TELQV (9) TAVQX Q (4) TELQX NOTE: 1. W is High for a Read Cycle. FIGURE 1. READ CYCLE Addresses must remain stable for the duration of the read cycle. To read, G and E must be VIL and W VIH. The output buffers can be controlled independently by G while E is low. To execute consecutive read cycles, E may be tied low continuously until all desired locations are accessed. When E is low, addresses must be driven by stable logic levels and must not be in the high impedance state. (10) TAVAX ADDRESS (14) TWHAX (11) TELWH E (12) TAVWL (13) TWLWH (20) TWLEH W (16) TWLQZ (19) TWHQX Q (21) TDVEH D (17) TDVWH (18) TWHDX (22) TAVWH NOTE: 1. G is Low throughout Write Cycle. FIGURE 2. WRITE CYCLE I To write, addresses must be stable, E low and W falling low for a period no shorter than TWLWH. Data in is referenced with the rising edge of W, (TDVWH and TWHDX). While addresses are changing, W must be high. When W falls low, the I/O pins are still in the output state for a period of TWLQZ and input data of the opposite phase to the outputs must not be applied, (Bus contention). If E transitions low simultaneously with the W line transitioning low or after the W transition, the output will remain in a high impedance state. G is held continuously low. 193 HM-65162/883 Timing Waveforms (Continued) (10) TAVAX ADDRESS (22) TAVWH G (11) TELWH (14) TWHAX E (12) TAVWL (13) TWLWH W TGHQZ (15) Q (21) TDVEH D (17) TDVWH (18) TWHDX FIGURE 3. WRITE CYCLE II In this write cycle G has control of the output after a period, TGHQZ. G switching the output to a high impedance state allows data in to be applied without bus contention after TGHQZ. When W transitions high, the data in can change after TWHDX to complete the write cycle. Low Voltage Data Retention Intersil CMOS RAMs are designed with battery backup in mind. Data retention voltage and supply current are guaran teed over temperature. The following rules ensure data retention: 1. Chip Enable (E) must be held high during data retention; within VCC -0.3V to VCC +0.3V. 2. On RAMs which have selects or output enables (e.g., S, G), one of the selects or output enables should be held in the deselected state to keep the RAM outputs high impedance, minimizing power dissipation. 3. Inputs which are to be held high (e.g., E) must be kept between VCC +0.3V and 70% of VCC during the power up and down transitions. 4. The RAM can begin operation > 55ns after VCC reaches the minimum operating voltage (4.5V). DATA RETENTION TIMING VCC 4.5V VCC 02.0V 4.5V >55ns E VCC -0.3V TO VCC +0.3V FIGURE 4. DATA RETENTION TIMING 194 HM-65162/883 Test Circuit DUT (NOTE 1) CL + - IOH 1.5V IOL EQUIVALENT CIRCUIT NOTE: 1. Test head capacitance includes stray and jig capacitance. Burn-In Circuits HM-65162/883 CERDIP TOP VIEW HM-65162/883 CLCC TOP VIEW F10 VCC C VCC F2 DQ1 DQ2 5 6 20 19 W G A10 E 7 18 8 17 9 16 10 15 DQ5 11 14 DQ4 12 13 DQ7 DQ6 DQ3 NC NC NC VCC NC A8 6 28 7 8 27 NC 26 W 9 25 10 24 F3 A0 11 23 F2 NC 12 DQ0 13 F7 F6 F5 F4 F2 F2 32 31 30 A5 F8 F2 1 29 F1 F0 2 5 F9 F13 3 4 A6 F12 F0 NC A7 21 F11 A4 A3 A2 A1 22 21 14 15 16 17 18 F2 F2 F2 GND 4 A9 A9 G A10 E DQ7 DQ6 19 20 DQ5 F2 DQ0 22 F2 F2 A0 3 DQ4 F3 A1 A8 F2 F4 A2 23 F2 F5 A3 2 NC DQ3 F6 A4 VCC GND F7 A5 24 F2 F8 A6 1 DQ2 F9 A7 DQ1 F10 C NOTES: NOTES: All resistors 47kW 5%. All resistors 47kW 5%. F0 = 100kHz 10%. F0 = 100kHz 10%. F1 = F0 / 2, F2 = F1 / 2, F3 = F2 / 2 . . . F13 = F12 / 2. F1 = F0 / 2, F2 = F1 / 2, F3 = F2 / 2 . . . F13 = F12 / 2. VCC = 5.5V 0.5V. VCC = 5.5V 0.5V. VIH = 4.5V 10%. VIH = 4.5V 10%. VIL = -0.2V to +0.4V. VIL = -0.2V to +0.4V. C = 0.01F Min. C = 0.01F Min. 195 F11 F12 F1 F0 F13 F0 F2 F2 HM-65162/883 Die Characteristics DIE DIMENSIONS: 180.3 x 194.9 x 19 1mils GLASSIVATION: Type: SiO2 Thickness: 8kA 1kA METALLIZATION: Type: Si - Al Thickness: 11kA 2kA WORST CASE CURRENT DENSITY: 1.7 x 105 A/cm2 Metallization Mask Layout HM-65162/883 A3 A4 A5 A6 A7 VCC A8 A9 W G A10 A2 A1 E A0 DQ7 DQ0 DQ1 DQ2 GND DQ3 DQ4 DQ5 DQ6 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 196