Multiprotocol XFP Optical Transceiver—1310 nm for up to
10 km Reach
JXP Series
Key Features •CompliantwithSONETOC-192SR-1,10GEthernetand10G
FibreChannel10GBASE-LR,andcorrespondingForward
ErrorCorrection(FEC)ratesfrom9.95Gbpsto11.35Gbps
•1310nmopticalsignalsforupto10kmreach
•RoHS6/6compliant
•Industrialoperatingcasetemperaturerangefrom
-40˚Cto85˚C
•Lowpowerconsumption(<2.5Wmax)
•ExcellentEMIperformance
•Digitaldiagnosticmonitoringsupport
•XFIsystemloopbackimplemented
The JDSU 10 Gbps 1310 nm multiprotocol XFP optical transceiver is a fully du-
plexed, integrated fiber optic transceiver that provides a high-speed serial link at
signaling rates from 9.95 to 11.35 Gbps. The module complies with the 10 Gigabit
Small Form Factor Pluggable (XFP) multisource agreement (MSA).
The 1310 nm XFP also complies with Telcordia GR-253-CORE (SONET) OC-192
SR-1 and ITU-T G.691 (SDH) STM-64 I-64.1 for 2 km reach, and IEEE 802.3-2005
Clause 52 (Ethernet) 10GBASE-LR and 10GFC (Fibre Channel) 1200-SM-LL-L
for 10 km reach.
The 10 Gbps multiprotocol XFP optical transceiver integrates the receive and
transmit path on one module. On the transmit side, the 10 Gbps serial data stream
is recovered, retimed, and passed to a laser driver. The laser driver modulates a
1310 nm semicooled external modulated laser (EML), enabling data transmission
over single-mode fiber through an industry standard LC connector. On the re-
ceive side, the 10 Gbps optical data stream is recovered from a PIN photodetector/
transimpedance amplifier, retimed, and passed to an output driver. This module
features a hot-pluggable, XFI-compliant electrical interface.
Applications
•Wideareanetwork(WAN)
•Localareanetwork(LAN)
•Storageareanetwork(SAN)
•SONETOC-192applications
•SDHSTM-64applications
•Ethernetswitchesandapplications
•FibreChannelswitchesandapplications
Compliance
•TelcordiaGR-253-COREstandard
•ITU-TG.691standard
•IEEE802.3-2005Clause52standard
•10GFC1200-SM-LL-Lstandard
•Class1LaserSafety
•TestedinaccordancewithTelcordia
GR-468
NORTH AMERICA: 800 498-JDSU (5378) WORLDWIDE: +800 5378-JDSU WEBSITE: www.jdsu.com
COMMUNICATIONS MODULES & SUBSYSTEMS
2
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
The 10 Gbps 1310 nm multiprotocol XFP optical transceiver is a fully duplexed
serial electric, serial optical device with both transmit and receive functions con-
tained in a single module that provides a high-speed serial link at signaling rates
from 9.95 to 11.35 Gbps. It is designed to be compliant with Telcordia GR-253-
CORE OC-192 SR-1 for 2 km reach (SONET), ITU-T G.691 STM-64 I-64.1 for 2
kmreach(SDH),IEEE802.3-2005Clause5210GBASE-LRand10GBASE-LWfor
10 km reach (Ethernet) and 10GFC 1200-SM-LL-L for 10 km reach (Fibre Chan-
nel). The transceiver is also fully compliant with the 10 Gigabit Small Form Factor
XFP Pluggable Module MSA INF8077i Rev. 4.5. A block diagram of the 10 Gbps
1310 nm multiprotocol XFP optical transceiver is shown in Figure 1.
The 10 Gbps 1310 nm multiprotocol XFP optical transceiver locks to data without
the requirement of reference clock. The reference clock inputs have an inter-
nal 100 Ω differential line-to-line termination. It has several low-speed interface
connections, including a two-wire serial interface. These connections include
module not ready (Mod_NR), module deselect (Mod_DeSel), Interrupt, trans-
mitter disable (TX_DIS), module absent (Mod_ABS), receive loss (RX_LOS), and
power down/reset (P_Down/RST).
The XFP transceiver also supports XFI loopback. In this mode, data input on the
electrical Tx pins of the XFP module is retimed and is redirected to the Rx pins of
the module. This facilitates system-side test and debug operations.
Transmitter
The transmitter path converts serial NRZ electrical data from line rate of 9.95 to 11.35
Gbps to a standard compliant optical signal. The transmitter accepts a 100 Ω differen-
tial 120 mV peak-to-peak to 820 mV peak-to-peak 10 Gbps CML electrical signal on
TD- and TD+ pins.
Inside the module, the differential signals pass through a signal conditioner with
equalization that compensates for losses and deterministic jitter present on the input
data stream. The transmit CDR function generates a clock that is at the same fre-
quency as the incoming data bit rate of the electrical data input. The clock is phase
aligned by a phase locked loop (PLL) that samples the data in the center of the data
eye pattern. The CDR function does not require a reference clock to “lock” to incom-
ing data. The CDR contains a lock detect circuit that indicates successful locking of
the PLL onto the incoming data.
The output of the Tx signal conditioner is input to the laser driver circuit, which
transforms the small swing digital voltage to an output modulation that drives a
semi-cooled, electroabsorption (EA) modulator. The optical signal is engineered to
meet the SONET/SDH, 10 G Ethernet, 10 G Fibre Channel and corresponding for-
ward error correction (FEC) rates specifications. Closed-loop control of the trans-
mitted laser power and modulation swing over temperature and voltage variations
is provided. The laser is coupled to single-mode optical fiber through an industry-
standard LC optical connector.
Section 1 Functional Description
3
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Receiver
The receiver converts incoming DC balanced serial NRZ optical data from line
rate of 9.95 to 11.35 Gbps into serial XFI electrical data. Light is coupled to a PIN
photodetector from single-mode optical fiber through an industry-standard LC
optical connector. The electrical current from the PIN photodetector is converted
to a voltage in a high-gain transimpedance amplifier.
The amplified signal is passed to a signal conditioning IC that provides clock and
data recovery. The receive CDR function generates a clock that is at the same fre-
quency as the incoming data bit rate of the optical data input. The clock is phase
aligned by a PLL that samples the data in the center of the data eye pattern. The
CDR function does not require a reference clock to “lock” to incoming data. The
CDR contains a lock detect circuit that indicates successful locking of the PLL onto
the incoming data. Loss of signal, and signal lock detection is included in the re-
ceive circuitry that is reflected in the Mod_NR status pin. The recovered data is
output on the RD+ and RD- pins as a 100 Ω 340 mV peak-to-peak CML signal.
The output signal meets the XFP MSA requirements.
Figure 1 JDSU 10 Gbps 1310 nm multiprotocol XFP optical transceiver functional block diagram
CDR / Limiting
Amplifier
RD-
RD+TIA
ROSA
CDR / Equalizer
TD-
TD+
TOSA
Laser Control
Circuit
Micro-
Processor
Vcc3Vcc5
Power Supply Sequence /
In Rush Control Circuit
Vcc2Vee5
No Connect
GND
Transceiver Ground
MOD_ABS
GNDREFCLK+
REFCLK-
RX_LOS
MOD_NR
INTERRUPT
SDA
SCL
MOD_DESEL
Vcc3Vcc3
TX_DIS
Vcc3
PDOWN/RST
4
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Low-speed Signaling
Low-speed signaling is based on low voltage TTL (LVTTL) operating at a nominal
voltage of 3.3 V.
SCL/SDA: Two-wire serial interface clock and data line. Hosts should use a pull-up
resistor connected to Vcc 3.3 V on the two-wire interface SCL (clock), SDA (data),
and all low speed outputs.
Mod_NR:Outputpin.Whenassertedhigh,indicatesthatthemodulehasdetecteda
condition that renders Tx and or Rx data invalid.
Mod_DeSel:Inputpin.Whenheldlowbythehostthemodulerespondstotwo-wire
serialcommunicationcommands.Whenhigh,themoduledoesnotrespondto,or
acknowledge any, two-wire interface communication from the host.
Interrupt:Outputpin.Whenlow,indicatespossiblemoduleoperationalfaultora
status critical to the host system.
TX_DIS:Inputpin.Whenassertedhigh,thetransmitteroutputisturnedoff.
Mod_ABS: Output pin. Asserted high when the XFP module is absent, and is pulled
low when the XFP module is inserted.
RX_LOS: Output pin. Asserted high when insufficient optical power for reliable sig-
nal reception is received.
P_Down/RST: Multifunction input pin. The module can be powered down or reset
by pulling the low-speed, P-Down pin high. In power-down mode, no data is trans-
mitted on the optical Tx or the electrical Rx path. The reset pulse is generated on the
falling edge of the P-Down signal. Following reset, the internal PLLs must reacquire
lock and will temporarily indicate a Mod_NR failure until the PLLs reacquire lock.
Recommended MSA connections to the 10 Gbps 1310 nm multiprotocol XFP opti-
cal transceiver are shown in Figure 2.
Power supply filtering is recommended for the JDSU 10 Gbps 1310 nm multipro-
tocol XFP optical transceiver. To limit wide band noise power, the host system and
module shall each meet a maximum of two percent peak-to-peak noise when mea-
sured with a one MHz low-pass filter. In addition, the host system and the module
shall each meet a maximum of three percent peak-to-peak noise when measured
with a filter from 1 – 10 MHz.
Section 2 Application Schematics
5
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Technical specifications related to the 10 Gbps 1310 nm multiprotocol XFP optical
transceiver includes:
•Section3.1 PinFunctionDenitions
•Section3.2 XFP/XFIReferenceModelCompliancePoints
•Section3.3 AbsoluteMaximumRatings
•Section3.4 OperatingConditions
•Section3.5 ElectricalCharacteristics
•Section3.6 JitterSpecications
•Section3.7 TimingRequirementofControlandStatusI/O
•Section3.8 XFPTwo-wireInterfaceProtocolandManagementInterface
•Section3.9 OpticalTransmitterCharacteristics
•Section3.10 OpticalReceiverCharacteristics
•Section3.11 RegulatoryCompliance
•Section3.12 PCBLayout
•Section3.13 ModuleOutline
•Section3.14 Connectors
Section 3 Specifications
Figure 2 Application schematics for the 10 Gbps 1310 nm XFP optical transceiver
TD +/-
RD +/-
2
2
Interrupt
Mod_Abs
Mod_NR
RX_LOS
5 V
+3.3 V
GND
2
SCL/SDA
TX_DIS
POWER INPUT OUTPUT
Mod_DeSel
P_Down/RST
XFP Module
CDR
CDR
System
Loopback
TIA
Laser
Driver
uController
ROSA
TOSA
LC
LC
6
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Power supply filter component values are provided on page 7.
Receiver (Tx Fault)
Vcc
10 kΩ
CMOS, TTL, or
Open Collector Driver
(Tx Disable)
�
�
�
Open Collector
Bidirectional
SDA
Vcc
Rp***
Vcc
�
�
�
Open Collector
Bidirectional
SCL
Rq ***
Mod_ABS
10 kΩ
Vcc
1 VeeT
2 Tx Fault
3 Tx Disable
4 SDA
5 SCL
6 MOD_ABS
7 RS0
8 LOS
9 RS1
10 VeeR
VeeT 20
TD- 19
TD+ 18
VeeT 17
VccT 16
VccR 15
VeeR 14
RD+ 13
RD- 12
VeeR 11
10 kΩ
Vcc
Receiver (LOS)
R1* 50 Ω
R2* 50 Ω
�
�
L1
�
�
�
L2
�
�
�
Z* = 100 ΩPECL Driver
(TX DATA)
C1
C2
C5C4
C3
CMOS or TTL Driver
(RS0 Rx Rate Select)
CMOS or TTL Driver
(RS1 Tx Rate Select)
�
�
�
�
Vcc
R6 ∗∗
R5 ∗∗
Vcc
�
Vcc +3.3V
Input
R3*
50 Ω
R4*
50 Ω
�
�
PECL Receiver
(RX DATA)
Z* = 100 Ω
Power Supply Filter
C6
�
Ry
Rx
�
�
�
�
�
�
�
�
�
�
�
�
3.1 Pin Function Definitions
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
GND
RD-
RD+
GND
VCC2
P_Down/RST
VCC2
GND
RefCLK+
RefCLK-
GND
GND
TD-
TD+
GND
GND
RX_LOS
Mod_NR
Mod_ASB
SDA
SCL
VCC3
VCC3
GND
VCC5
TX_DIS
Interupt
Mod_DeSel
VEE5
GND
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Toward ASIC
Toward Bezel
TX_DIS
_______
Interrupt
Figure 3 XFP optical transceiver pin-out on host board
7
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Pin Number Type Name Description
1 GND1 Module Ground
2 VEE5 Not used; may be left unconnected (Optional -5.2 V Power Supply)
3 LVTTL-I Mod_Desel ModuleDeselect;Whenheldlowallowsthemoduletorespond
to two-wire serial interface commands
4 LVTTL-O Interrupt2 Interrupt; Indicates presence of an important condition which
can be read over the serial two-wire interface
5 LVTTL-I TX_DIS Transmitter Disable; Transmitter Laser Source Turned Off
6 VCC5 +5 V Power Supply
7 GND1 Module Ground
8 VCC3 +3.3 V Power Supply
9 VCC3 +3.3 V Power Supply
10 LVTTL-I SCL2 Two-wire Interface Clock
11 LVTTL-I/O SDA2 Two-wire Interface Data Line
12 LVTTL-O Mod_Abs2 Indicates Module is not present. Grounded in the Module
13 LVTTL-O Mod_NR2 Module Not Ready; Indicating Module Operational Fault
14 LVTTL-O RX_LOS2 Receiver Loss Of Signal Indicator
15 GND1 Module Ground
16 GND1 Module Ground
17 CML-O RD- Receiver Inverted Data Output
18 CML-O RD+ Receiver Noninverted Data Output
19 GND1 Module Ground
20 VCC2 +1.8 V Power Supply (not used)
21 LVTTL-I P_Down/RST Powerdown;Whenhigh,themodulelimitspowerconsumption
to1.5Worbelow.Serialinterfaceisfunctionalinthelowpowermode.
Reset; The falling edge initiates a complete reset of the module
including the serial interface, equivalent to a power cycle.
22 VCC2 +1.8 V Power Supply (not used)
23 GND1 Module Ground
24 PECL-I RefCLK+ Reference Clock Noninverted Input (not used)
25 PECL-I RefCLK- Reference Clock Inverted Input (not used)
26 GND1 Module Ground
27 GND1 Module Ground
28 CML-I TD- Transmitter Inverted Data Input
29 CML-I TD+ Transmitter Noninverted Data Input
30 GND1 Module Ground
1. Module ground pins (GND) are isolated from the module case and chassis ground within the module
2. Shall be pulled up with 4.7 kΩ – 10 kΩ to a voltage between 3.15 V and 3.45 V on the host board
Table 1 XFP Optical Transceiver Pin Descriptions
8
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
3.2 XFP/XFI Reference Model Compliance Points
Figure 4 XFP optical transceiver model compliance points
ASIC/
SERDES
AB'B
CC'D
RX
TX
Connector
XFP Module
Parameter Symbol Ratings Unit
Storage temperature Tst -40 to +85 ˚C
Operating case temperature TOP -40 to +85 ˚C
Relative humidity RH 5 to 85 (noncondensing) %
Static electrical discharge (Human Body Model) ESD 500 V
Power supply voltages VCC3, max -0.3 to 3.63 V
V
CC5, max -0.5 to 6.0 V
Receive input optical power (damage threshold) Pdth 5 dBm
Note:
Absolute maximum ratings represent the damage threshold of the device. Damage may occur if the device is operated above the limits stated here except for brief excursions.
Performance is not guaranteed and reliability is not implied for operation at any condition outside the recommended operating limits.
3.3 Absolute Maximum Ratings
Part Number SONET/SDH and FEC 10GbE/10GFC Industrial Commercial
(9.95 to 11.35 Gbps) and FEC Temperature Temperature
(9.95 to 11.27 Gbps) (-40˚C to 85˚C) (-5˚C to 70˚C)
JXP-01LMAB1 X X X X
JXP-01LMAC1 X X X
JXP-01LEAB1 X X X
JXP-01LGAB1 X X
Note:
Performance is not guaranteed and reliability is not implied for operation at any condition outside the recommended operating limits.
3.4 Operating Conditions
9
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Parameter Symbol Minimum Typical Maximum Unit Notes
Supplycurrentsandvoltages
Voltage3 VCC3 3.13 3.3 3.47 V WithrespecttoGND
Voltage5 VCC5 4.75 5 5.25 V WithrespecttoGND
Voltage2 VCC2 1.8 V Not used
Supply current3 ICC3 750 mA
Supply current5 ICC5 500 mA
Supply current2 ICC2 0 mA VPS; Not used
Powerdissipation Pwr 2.5 W
Low-speedcontrolandsensesignals(detailedspecicationinXFPMSAINF8077iRev.4.5)
Outputs (Interrupt, VOL 0 0.4 V Rpullup pulled to host _Vcc,
Mod_NR, RX_LOS) measured at host side of connector.
I
OL(max)=3 mA
V
OH host_Vcc-0.5 host_Vcc+ 0.3 V Rpullup pulled to host _Vcc,
measured at host side of connector
Inputs (TX_DIS, VIL -0.3 0.8 V Pulled up in module to Vcc3
P_Down/RST, M_DSEL) VIH 2 Vcc3+ 0.3 V Pulled up in module to Vcc3
SCL and SDA Inputs VIL -0.3 Vcc3*0.3 V Rpullup pulled to host _Vcc,
measured at XFP side of connector
V
IH Vcc3*0.7 Vcc3+0.5 V Rpullup pulled to host _Vcc,
measured at XFP side of connector
Transmitterinput(detailedspecicationinXFPMSAINF8077iRev.4.5)
Data input baud rate nominal 9.95 11.35 Gbps
Data input bit rate tolerance -100 +100 ppm
(10GbE/10GFC)
Data input bit rate tolerance -20 +20 ppm
(SONET/SDH)
Data input compliance B Internally AC coupled signals
Data input differential RI 90 100 110 Ω
impedance
Receiveroutput(detailedspecicationinXFPMSAINF8077iRev.4.5)
Data output baud rate nominal 9.95 11.35 Gbps
Data output compliance C internally AC coupled signals
Data output bit rate stability -100 +100 ppm
(10GbE/10GFC)
Data output bit rate stability -20 +20 ppm
(SONET/SDH)
3.5 Electrical Characteristics
10
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Parameter Symbol Min Max Unit Notes
TransmitterelectricalinputjitterfromhostatB(detailedspecicationinXFPMSAINF8077iRev.4.5)1
Total non-EQJ jitter 0.41 UI(p-p) Total jitter less ISI
Total jitter TJ 0.61 UI(p-p)
Eye mask X1 0.305 UI Mask coordinate X1=0.205 if total non-DDJ
is measured
Eye mask Y1 60 mV
Eye mask Y2 410 mV 50 mV is allocated for multiple reflections
ReceiverelectricaloutputjittertohostatC(detailedspecicationinXFPMSAINF8077iRev.4.5)1
Deterministic jitter DJ 0.18 UI(p-p) Includes jitter transferred from the optical receiver
during any valid operational input condition.
Total jitter TJ 0.34 UI(p-p) Includes jitter transferred from the optical receiver
during any valid operational input condition.
Eye mask X1 0.17 UI
Eye mask X2 0.42 UI
Eye mask Y1 170 mV
Eye mask Y2 425 mV
Telecommoduleopticaltransmitterandreceiverjitter(detailedspecicationinXFPMSAINF8077iRev.4.5andGR-253-CORE
Issue4-2005)2
JittertransferbandwidthBW 8 MHz PRBS231-1, OC-192 /
SDH-64 Sinusoidal Jitter Tolerance Mask
Jitter peaking 1 dB Frequency >120 KHz
Transmitter jitter generation 0.3 UIpp 20 KHz to 80 MHz
0.1 UIpp 4 MHz to 80 MHz
Datacommoduleopticaltransmitterandreceiverjitter(detailedspecicationinXFPMSAINF8077iRev.4.5)1
Jittertransferbandwidth BW 8 MHz PRBS231-1, Data or scrambled 64 B/66 B as
detailed in IEEE 802.3-2005 Clause 52
Jitter peaking 1 dB Frequency >50 KHz
1. Specifications are applicable to all Part Numbers listed in Section 3.4.
2. Specifications are applicable to SONET / SDH compliant Part Numbers listed in Section 3.4 only.
3.6 Jitter Specifications
Parameter Symbol Min Max Unit Notes
TX_DIS assert time t_off 10 µsec Rising edge of TX_DIS to fall of output signal below
10% of nominal
TX_DIS negate time t_on 2 msec Falling edge of TX_DIS to rise of output signal above
90% of nominal
Time to initialize t_init 300 msec From power on or from falling edge of P_Down/RST
Interrupt assert delay Interrupt_on 200 msec From occurrence of the condition triggering Interrupt.
Interrupt negate delay Interrupt_off 500 µsec From clear on read Interrupt flags
P_Down/RST assert delay P_Down/RST_on 100 µsec From power down initiation
Mod_NR assert delay Mod_NR_on 1 msec From occurrence of fault to assertion of Mod_NR
Mod_NR negate delay Mod_NR_off 1 msec From clearance of signal to negation of Mod_NR
P-Down reset time 10 µsec Min. length of P-Down assert to initiate reset
RX_LOS assert delay t_loss_on 100 µsec From Occurrence of loss of signal to assertion of RX_LOS
RX_LOS negate delay t_loss_off 100 µsec From Occurrence of return of signal to negation of RX_LOS
Note:
Two-wire serial bus timing is described in Chapter 4 of XFP MSA INF8077i Rev. 4.5.
3.7 Timing Requirement of Control and Status I/O
11
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
3.8 XFP Two-wire Interface Protocol and Management Interface
The 10 Gbps 1310 nm multiprotocol XFP optical transceiver incorporates a XFP
compliant two-wire management interface which is used for serial ID, digital
diagnostics, and certain control functions. It is modeled on the SFF-8472 Rev
9.3 specification modified to accommodate a single two-wire interface address.
In addition to the basic I2C read/write functionality, the modules support packet
error checking that, when enabled, allows the host system to confirm the validity
of any read data. Details of the protocol and interface are explicitly described in the
MSA. Please refer to the MSA for design reference.
Figure 5 XFP two-wire serial digital diagnostic memory map
Two-wire Serial Address
1010000x (A0H)
Digital
Diagnostic
Functions
4 Byte Password Change
4 Byte Password Entry
Page Select Byte Entry
0-
118
119-122
126
127
User
EEPROM
Data
XFP MSA
Serial ID
Data
Vendor Specific
ID Data
Reserved
For Future
Diagnostic
Functions
Vendor
Specific
Functions
Reserved
128-
255
128- 128-128- 128-
255 255255255
223
224-
Table 00HTable 01HTable 02HTable 03H-7FH Table 80H-FFH
12
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Parameter Symbol Minimum Typical Maximum Unit
Center wavelength λ 1290 1330 nm
-20 dB spectral width ∆λ 1 nm
Sidemode suppression ratio SSR 30 dB
Relative intensity noise RIN12OMA -128 dB/Hz
Average optical power (SONET/SDH) (EOL) Pavg -6.0 -1.0 dBm
Extinction ratio1 (SONET/SDH) ER 6 7 dB
Chromatic dispersion penalty PCD 6.6 ps/nm
Optical path penalty DP 1.0 dB
Return loss tolerance 14 dB
Datacommoduleopticaltransmittercharacteristics2
OMA (optical modulation amplitude) OMA -5.2 dBm
Transmitter and dispersion penalty TDP 3.9 dB
Average optical power (10GbE/10GFC) (EOL) Pavg -8.2 0.5 dBm
Extinction ratio1 (10GbE/10GFC) ER 3.5 dB
1. Tested with PRBS 231-1 pattern
2. Applicable to non SONET/SDH compliant Part Numbers listed in Section 3.4 only.
3.9 Optical Transmitter Characteristics
Parameter Symbol Minimum Typical Maximum Unit
Center wavelength λ 1260 1600 nm
Receiver sensitivity1 R
sen -14.4 dBm
Stressed receive sensitivity2 SRS -10.3 dBm
Receive overload3 P
max 1 dBm
Receiver reflectance Rrx -14 dB
LOS assert Plos_on -30 -20 dBm
LOS deassert Plos_off -18.5 dBm
LOS hysteresis 0.5 6 dB
Note: Specifications are applicable to the operating temperature range listed in Section 3.4
1. Guaranteed at 10.709 Gbps. Measured with worst ER; BER<10-12; 231-1 PRBS. Equivalent to -12.6 dBm OMA at ER = 6 dB.
2. Guaranteed at 11.35 Gbps.
3. Guaranteed up to 10.709 Gbps.
3.10 Optical Receiver Characteristics
13
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Feature Test Method Performance
Component safety UL 60950 UL Certificate
UL94-V0 UL Certificate
EN 60950 TUV Report/Certificate (CB Scheme)
RoHS-compliance Directive 2002/95/EC Compliant per the Directive 2002/95/EC of the European
Parliament and of the Council of 27 January 2003 on the
restriction of the use of certain hazardous substances in
electrical and electronic equipment.
Laser eye safety EN 60825 TUV Certificate
U.S. 21CFR (J) 1040.10 CDRH compliant and Class 1 laser safe.
ElectromagneticCompatibility
Electromagnetic emissions EMC Directive 89/336/EEC Noise frequency range: 30 MHz to 40 GHz.
FCC CFR47 Part 15 Good system EMI design practice required
IEC/CISPR 22 to achieve Class B margins.
AS/NZS CISPR22
EN 55022
ICES-003, Issue 4
VCCI-03
Electromagnetic immunity EMC Directive 89/336/EEC
IEC /CISPR/24
EN 55024
ESDimmunity EN61000-4-2 Exceedsrequirements.Withstandsdischargesof;
8 kV contact, 15 kV air
Radiated immunity EN 61000-4-3 Exceeds requirements. Field strength of 10 V/m RMS,
from 10 MHz to 1 GHz. No effect on transmitter/receiver
performance is detectable between these limits.
Table 2 Regulatory Compliance
3.11 Regulatory Compliance
The 10 Gbps 1310 nm multiprotocol XFP optical transceiver is lead-free and RoHS
6/6 compliant per Directive 2002/95/EC of the European Parliament and of the
Council of 27 January 2003 on the restriction of the use of certain hazardous sub-
stances in electrical and electronic equipment.
The JDSU 10 Gbps 1310 nm multiprotocol XFP optical transceiver complies with
international electromagnetic compatibility (EMC) and international safety re-
quirements and standards. EMC performance is dependent on the overall system
design. Information included herein is intended as a figure of merit for designers
to use as a basis for design decisions.
3.12 PCB Layout
Recommended PCB layout is given in XFP MSA INF8077i Rev. 4.5.
14
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
3.13 Module Outline
Figure 6 Belly-to-Belly Mounting Recommendation
3.14 Connectors
Fiber
The XFP module has a duplex LC receptacle connector.
Electrical
The electrical connector is the 30-way, two-row PCB edge connector. Customer
connector is Tyco/AMP Part No. 788862C or equivalent.
15
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Other information related to the 10 Gbps 1310 nm multiprotocol XFP optical
transceiver includes:
•Section4.1PackingandHandlingInstructions
•Section4.2ESDDischarge(ESD)
•Section4.3EyeSafety
4.1 Package and Handling Instructions
Connector covers
The 10 Gbps 1310 nm multiprotocol XFP optical transceiver is supplied with an
LC duplex receptacle. The connector plug supplied protects the connector dur-
ing standard manufacturing processes and handling by preventing contamination
from dust, aqueous solutions, body oils, or airborne particles.
Note: It is recommended that the connector plug remain on whenever the trans-
ceiver optical fiber connector is not inserted.
Recommended cleaning and degreasing chemicals
JDSU recommends the use of methyl, isopropyl and isobutyl alcohols for cleaning.
Do not use halogenated hydrocarbons (trichloroethane, ketones such as acetone,
chloroform, ethyl acetate, MEK, methylene chloride, methylene dichloride, phenol,
N-methylpyrolldone).
This product is not designed for aqueous wash.
Housing
The 10 Gbps 1310 nm multiprotocol XFP optical transceiver housing is made from
zinc.
4.2 ESD Discharge (ESD)
Handling
Normal ESD precautions are required during the handling of this module. This
transceiver is shipped in ESD protective packaging. It should be removed from
the packaging and otherwise handled in an ESD protected environment utilizing
standard grounded benches, floor mats, and wrist straps.
Test and operation
In most applications, the optical connector will protrude through the system chas-
sis and be subjected to the same ESD environment as the system. Once properly
installed in the system, this transceiver should meet and exceed common ESD test-
ing practices and fulfill system ESD requirements.
Typical of optical transceivers, this module’s receiver contains a highly sensitive
optical detector and amplifier which may become temporarily saturated during
an ESD strike. This could result in a short burst of bit errors. Such an event might
require that the application reacquire synchronization at the higher layers (serial-
izer/deserializer chip).
Section 4 Related Information
4.3 Eye Safety
The JDSU 10 Gbps 1310 nm multiprotocol XFP optical transceiver is an interna-
tional Class 1 laser product per IEC 60825-1 second edition 2007. The product
also complies with U.S.A. regulations for Class 1 products contained in 21 CFR
1040.10 and 1040.11. Laser emissions from Class 1 laser products are not consid-
ered hazardous when operated within the limits of this specification.
Operating this product in a manner inconsistent with intended usage and specifi-
cation may result in hazardous radiation exposure.
Caution
Tampering with this laser based product or operating this product outside the
limits of this specification may be considered an act of “manufacturing,” and will
require, under law, recertification of the modified product with the U.S. Food and
Drug Administration (21 CFR 1040).
NORTH AMERICA: 800 498-JDSU (5378) WORLDWIDE: +800 5378-JDSU WEBSITE: www.jdsu.com
Product specifications and descriptions in this document subject to change without notice. © 2009 JDS Uniphase Corporation 30149346 003 0409 JXP-01LXAX1.DS.CMS.AE April 2009
MULTIPROTOCOL XFP OPTICAL TRANSCEIVER
—1310 NM FOR UP TO 10 KM REACH
Ordering Information
For more information on this or other products and their availability, please contact your local JDSU account manager or
JDSU directly at 1-800-498-JDSU (5378) in North America and +800-5378-JDSU worldwide, or via e-mail at
customer.service@jdsu.com.
Sample: JXP-01LMAB1
Product Code Description
JXP-01LMAB1 Multiprotocol,OC-192SR-1,10GbE/FCLR/LW,1310nm,industrialtemperaturerange10GbpsXFPopticaltransceiver
JXP-01LMAC1 Multiprotocol,OC-192SR-1,10GbE/FCLR/LW,1310nm,commercialtemperaturerange10GbpsXFPopticaltransceiver
JXP-01LEAB1 10GbE/FCLR/LW,1310nm,industrialtemperaturerange10GbpsXFPopticaltransceiver
JXP-01LGAB1 10GbE/FCLR/LW,1310nm,commercialtemperaturerange10GbpsXFPopticaltransceiver
CLASS 1 LASER PRODUCT
